A.G.
PATIL POLYTECHNIC INSTITUTE ,SOLAPUR
PR NO.1:- Locate components of CAD classic screen by creating
new drawing .CAD screen layout, drawing area, menu and
toolbars, status bar.
PR NO.2:- Work with toolbar and commands.
NAME : Laxman govind chimade
CLASS : S.Y.E.E. ROLL NO : 242 SIGNATURE :
SHEET NO : 1 DATE : 21.02.2024
A.G. PATIL POLYTECHNIC INSTITUTE ,SOLAPUR
PR NO.3:- Change the drawing limits, creating rectangle etc.
saving drawing for first time.
PR NO.4:- Draw line diagram using absolute coordinate
method.
Use LIMITS, UNITS, LINE, ARC, Commands: Absolute
coordinate method.
NAME : Laxman govind chimade
CLASS : S.Y.E.E. ROLL NO : 242 SIGNATURE :
SHEET NO : 2 DATE : 23.02.2024
A.G. PATIL POLYTECHNIC INSTITUTE ,SOLAPUR
PR NO.5:- Draft set-up: units, angle, area, coordinator
system, limits, grid, object snap.
PR NO.6:- Create two-dimensional drawings using
draw commands- line and circle.
NAME : Laxman govind chimade
CLASS : S.Y.E.E. ROLL NO : 242 SIGNATURE :
SHEET NO : 3 DATE : 23.02.2024
A.G. PATIL POLYTECHNIC INSTITUTE ,SOLAPUR
PR NO.7:- Draw a line diagram using relative coordinator and
relative polar coordinator method. Use LIMITS, UNITS, LINE ,
ARC, Commands : Relative coordinator and relative polar
coordinator method.
PR NO.8:- Draft set-up: units, angle, area, coordinator system,
limits, grid, object snap.
NAME : Laxman govind chimade
CLASS : S.Y.E.E. ROLL NO : 242 SIGNATURE :
SHEET NO : 4 DATE : 28.02.2024
A.G. PATIL POLYTECHNIC INSTITUTE ,SOLAPUR
PR NO.9:- Create two-dimensional drawings using
draw commands- line and circle.
PR NO.10:- Draw a 2D figure using Draw and Modify
commands. Use LINE, CIRCLE, OFFSET, TRIM, FILLET
Commands.
PR NO.11:- Modify two dimensional drawings using modify
commands- offset ,trim, fillet.
NAME : Laxman govind chimade
CLASS : S.Y.E.E. ROLL NO : 242 SIGNATURE :
SHEET NO : 5 DATE : 28.02.2024
A.G. PATIL POLYTECHNIC INSTITUTE ,SOLAPUR
PR NO.12:- Draw isometric drawing of electrical machine. Use
LIMITS, UNITS, ZOOM, GRID, SNAP, LINE, COPY,
ISOPLANE, ELLIPSE, TRIM, ERASE, PROPERTIES, SAVE
commands.
PR NO.13:- Draft Set-up: units, limits, zoom, grid, object snap,
ortho mode.
PR NO.14:- Snap and grid-snap spacing, grid spacing, isometric
snap type.
NAME : Laxman govind chimade
ISOMETRIC PROJECTION CLASS : S.Y.E.E. ROLL NO : 242 SIGNATURE :
SHEET NO : 6 DATE : 01.03.2024
ELECTRICAL CIRCUIT DIAGRAM
A.G. PATIL POLYTECHNIC INSTITUTE ,SOLAPUR
PR NO. 15 :- Create a simple drawing using electrical CAD
software for the given electrical circuit diagram.
PR NO.16:- Create a simple drawing using electrical CAD
software for the given electrical circuit diagram.
PR NO.17:- Draw the layout of the 11 kV/400V distribution
substation using electrical CAD software.
NAME : Laxman govind chimade
CLASS : S.Y.E.E. ROLL NO : 242 SIGNATURE :
SHEET NO : 7 DATE : 01.03.2024
