MongGoa

Semi-automatic Urine Analyzer

For veterinary use only

Operating Manual

Jiangsu Accuracy Biotechnology Co., Ltd.

1 Product Information

1.1 Introduction
Intended use: the semi-auto urine analyzer is used in medical institutions
for semi-quantitative detection of biochemical composition in canine and
feline urine through reading and evaluating the matched test strips
specified by our company. Urinalysis includes the following items:
leucocytes (LEU), nitrite (NIT), urobilinogen (UBG), protein (PRO), potential
of hydrogen (pH), blood (BLD), specific gravity (SG), ketones (KET),
bilirubine (BIL), glucose (GLU), vitamin C (VC), calcium (Ca), creatinine (Cr)
and microalbumin (MA).

Main features:
Small and exquisite with stylish design and easy to carry.
Easy operation, measurement completing by pressing one button.
Built-in rechargeable lithium battery can support you to finish the
detection at anytime.
Bluetooth Transmission is supported.
Compatible with urine test strips of 11 to 14 test items.
Detachable test strips holder, easy to clean and reduce pollution.

1.2 Contraindications
None

1.3 Working Principle

A prepared test strip is placed on the test strip holder, which moves it into
the analyzer and under the reading head. The analyzer reads the gray
reference pad first, and then reads each of the test pads on the strip.
The analyzer contains light-emitting diodes (LEDs) that emit light at various
wavelengths. The LED emits light of a defined wavelength onto the surface
orthe test pad at an optimum angle. The light hitting the test zone is
retlected more or less
intensely depending on the color produced on the
test pad, and is
picked up by the detector, a phototransistor positioned
directly above the test zone. The phototransistor sends an analog electrical
SIgnal to an A/D converter, which changes it to digital form. The
icroprocessor then converts this digital reading to a relative retlectance
value by referring it to a calibration standard.
1
Finally, the analyzer compares the reflectance value with the defined range
limits (reflectance values that are programmed into the analyzer for each
parameter) and outputs the result.

1.4 Components
1.4.1 Front View
Power switch| Direction button| Setup button|
Function of Power switch ( ) :
Display screen
Press and hold this button for 3 seconds to
turn the analyzer on or off.
At any display: press this button to quit the
currentdisplay and return
to the main display.
Function of Direction (<, >) button:
Measure button
At main display: Press or to review the previous results forward
or backward one by one.

Function of Measure ( button: At main display: Press or to

reviewthe previous results fonward
At main display or data inquiry display: Press this button to enter the
or backward quickly.
At setup display: Press < or to change the setting items.
measurement waiting display.
At USB or BLU setup display: Press or to open or close the
At measure waiting display: Press and hold this button to start the
related function.
quick measurement.
At other displays: Press this button to confirm the current operation or
Function of Setup (O) button:
A t main display: Press this button to enter the setup display.
save the settings.
1.4.3 Test Strip Holder

1.4.2 Side View Transmission teeth

ILTITITAIIIIIIIIIIIIIIIIII Positioning
| device

Test strip notch Standard reference pad

MicroUSB connector Test strip holder

NOTE:
Some models of analyzer have this MicroUSB connector.

2 3
 1.4.4 Display
unattended when using AC power supply.
Do not leave the equipment
placed. Keep it from falling, strong
5 67 The anaylzer should be appropriately mechanical
damage.
children or other
vibration, pets, pests,
88/B8/eDBB 0 Do not drop anything or put
it into the m e a s u r e m e n t entry of
the analyzer,

o8888P 8888B except for those items specified

in this manual.
locations where aerosol droplets or oxygen
LEU+8 BLD+8 Do not u s e the equipment in

NIT+8 KET +8 controlled.

urine analyzeroutdoor.
UBG+8 BIL+8 Donot use the
3 PRO+8 GLU +8
pH 8.8 vc +8
CAUTION
SG1.OBe MA +8 with adapter.
Ca+8 Cr +8 Unplug the power cord after charging the analyzer
the analyzer in place
Do not place the analyzer into the liquid, and do not put
4 88:88:88
where may fall into liquids.
Do not place the analyzer in location that is easy to fall, falling and crashing
1. Date (date/month/year) may cause the malfunction of analyzer.
2. System error code area, measurements records Toensure user safety, use only parts and accessories specified by Accuracy or
in this manual.
. Detection items and results area
Do not use the analyzer if it is not working properly or damaged.
4 Time(hour/minute/second) Do not place the analyzer or its data cable on the object surface with higher
5. Bluetooth icon(displays when starting Bluetooth function) temperature.

6. USB icon(displays when starting US8 function) Donot place anything on thetop of theanalyzer.
7. Battery status indicator
Menu, function code area
NOTE
8. The pictures and interfaces in this manual are for reference only.
This manual is based on the maximum configuration and therefore some
contents may not apply to your product. If you have any questions, please
1.5 Safety Information contact us.

WARNING

Before using the analyzer, you need access to professional medical 1.6 Symbols
Some symbols may not appear
knowledge. on your equipment.
equipment; any improper operation
may
the
Follow the instructions to use

measurements. Symbol Explaination SymbolExplaination

lead to inaccurate
operation.
Wear protective glovesto avoid bacterial infection during IVDn vitro diagnostic medical
o r abandoned strips.
Care must be taken
when dealing with urine samples
device Max. Stack Quantity
to lead to infection.
of operations is likely
Any incorrect sequence
o r self-treatment
through
making self-judgment |Keep dry
It is very dangerous for
user

Please follow the

doctor's advice. Self-judgment
may Fragile
measurements.
the Keep away from sunlight
make the disease worse. result in a fire Biological risks
other adapters may
power adapter. Using
Use only the specific Pressure
or electric shock. 11 This End up

5
2 Installation

2.1 Getting Started

Before unpacking, examine the packing case carefully for signs of damage. If
any damage is detected, contact the carrier.
If the packing case is intact, open the packing case in a right way, take out
the analyzer and its accessories from the packing case, and check according
to the Packing List. Check all materials as per the packing list and check for
any mechanical damage. If you have any questions, please contact us.
Fill in the service warranty card carefully, and return it to our company, so
that we can track the quality of products and supply you our service timely.

NOTE:
Please save the packaging materials for future transport or storage use.
Keep the packing material out of children's reach. Dispose of the packaging
material, observing the applicable waste control regulations
The system may be contaminated by microorganism during transport, storage and
use. Verify the packaging, especially the packaging for the single use accessories,
is intact. In case of any damage, contact the carrier or our company immediately.

2.2 Environmental Requirements

The operating environment of the equipment must meet the requirements
specified in this manual.
Do not use the analyzer in places where are wet, containing corrosive gases,
with strong dust, strong electromagnetic interference to ensure the normal
use of it.
When the analyzer is moved from one place to another, condensation may
occur because of temperature or humidity difference. In this case, never
start the analyzer before the condensation disappears.
Environment requirements:
Operating environment Temperature: 5°C35°C;
Relative humidity: s80%RH;
Atmospheric Pressure: 70kPa~106kPa

Storage and Temperature: -20°C 55°C;

transportation Relative humidity: s85%RH;
environment Atmospheric Pressure: 70kPan-106kPa
 stable surface. Do thee
The analyzer should be placed on a clean,
not use
3 Operation
analyzer in direct sunlight or splashing places.
clinical professionals under their
The analyzer is intended for use only by or

2.3 Connect the Power supply guidance. It must only be used by persons who have
received adequate
The analyzer can be powered by AC or built-in rechargeable Li-ion battery. operations of the analyzer by unauthorized or
training in its use. Any
untrained person are prohibited.
Power Requirements:
Main unit: DC 5V, 2A; AC 100V-240V+10%, 50/60Hz 3.1 Power On/Off
1. Before you start to make measurements, check the analyzer for any
NOTE: mechanical damage and make sure that accessories are properly
Use only the power adapter supplied or specified by Accuracy. connected.

Plug the adapter into the AC power source. If you run the analyzer
on
2.
2.4 Powered by Battery battery power, ensure that the battery is sufficiently charged.
The analyzer can be powered by built-in rechargeable Li-ion battery. If the 3. Press the button O for 3 seconds, "Beep" "Beep" will heard and the
AC power supply is suddenly off, the analyzer can be powered by battery. display screen of the analyzer will light on, self-test screen is displayed,
The battery will be charged when the analyzer is connected to AC power the transmission teeth starts moving.
supply. 4. The analyzer displays the main display after finishing the self-test.
5. Press and hold button for 3 seconds to turn off the analyzer after
On-screen battery symbols indicate the battery status as follows: finishing the measurement.
Indicates that the batteries work correctly. The solid portion
represents the current charge level of the batteries in proportion WARNING
to their maximum charge level. When the above indicator is Do not use the analyzer ifit is mechanically damaged or appears abnormal.
flashing, it indicates that the battery is low. Please charge it in Contact our company or our service personnel.
time.
The analyzer will not turn on when battery is lowif battery power used only
Indicates that the battery with full capacity.
3.2 Starting
NOTE: The self-test display is shown as right 22/c9/20 S 0
Do charge the battery separately with other charger.
not figure.
the Note: The figures shown in this manual are for
charge
t is
battery that
with power adapter supplied or specified by Accuracy
reference only. Please refer to the actual display
recommended you charge the battery within 2 months to ensure proper
use of the
analyzer long period no use of it.
if
Ensure that the battery has enough capacity in measurement; lower capaciy
lead to inaccurate results.

00:00:60

9
 1. Preparing test stripP
If self-test error, the error code (ERR 002) 29/09/20 IS 0& urine test strip with the urine sample,
will display on screen, the analyzer issueda Use pipette to flood the
a
moistened. Do not bend the
the test pads are
long "Beep" alarm sound. making sure that all
strip.
Press button t o return to the main
display, and restart the analyzer. Please
contact our service personnel if the error
ERR 002 still exits.

and then the back of the

b) Briefly (about one second) dab the long edge
622:36 paper towel).
test strip on an absorbent surface (e.g, a

The analyzer enters the main display shown 9/09/20 iS 0 a

as right figure after finishing self-test.
NO. 0000 indicates that no record in
LEU BLD
analyzer. If there are results, the analyzer KET
NIT
will display the latest result after turning Place the test strip, with the test pads facing up, into the strip holding
UBG BIL c)
on.
PRO GLU notch of the holder. Slide the strip along the holder until it touches the
pH vC end of the notch.
MA
Ca Cr
S:50 2
NOTE:
has results. For example, 0005 means the fifth
Number indicates that the analyzer
result of measurements.
The analyzer can store up to 1000 results. When the results is up 1000, "FULL",
the screen, the analyzer can used to measure, however the
"1000" will flash on
result will not store in analyzer.

Using Direction buttons ( , >) to view the results forward or backward. NOTE:
Use a clean urine cup and collect the fresh urine than 2 hours) for
(not more
testing.
3.3 Urine Analysis T h e bottom
CAUTION:
of the strip should be in full contact with the end of the notch.
Only remove the excess urine on sides
Please protective gloves to prevent contamination during operation.
T h e urine
of the strip.
wear
too high or too low. sample viscosity ensures that the strip is in close contact with the notch.
Do not use the analyzer if the ambient temperature measurement accuracy will If the
strip and the notch are dry, the test strip may slide and result in inaccurate
the
not the analyzer in direct sunlight place; measurements.
Do use

be affected. when Test strip should be taken with the use.

holder to avoid collisions Do not use the strip
that for a placed period
the front of the test strip
Do not place anything on of time.
the holder is moving8 Vitamin C in urine can cause illusion of
low level content of glucose and occult
blood. Make a new measurement
after asking the animal to stop taking vitamin C.

10 11
 Starting t h e m e a s u r e m e n t
2 press the 22/09/20 Is 0 The measurement displays after 29/09/2o 15 0
a
Place the strip well, and e)
S6 finishing the test as shown on right MOCOCS
Measure button (), the measure

waiting display is appeared (refer

to figure. LEU BLD
the right figure, the analyzer starts NIT KET
Note: At measurements display, UBG BIL
60-second countdown). The analyzer
will start the measurement till the press the Measure button ( ) to PRO GLU+
timer ends. start another test. pH 6.S ve+3
SGI.O3O MA
Ca
b) At measure waiting display, press
00:00:S0 5:50:S4
and hold the Measure button ( )
for 3 seconds to start the fast test.
The analyzer will skip the 60-second 3.4 Normal and Quick Test
countdown and begin a fast test. Normal test: Press Measure button (O) at the main display, the analyzer
Note: At any display, press the button will enter the countdown display. And then the analyzer will test the strip
can quit the current display and return to automaticly after 60 seconds completed.
the main display.
22109/20 15 0
c) "tESt" will appear on the screen 22109/20 S 0
during the urine analysis. Testing EESE
process will last about 10 to 20
seconds. Do not disturb or move the
analyzer.
Note: Do not move or knock the test strip holder
during the measurement. Otherwise, it
may cause the incorrect measurements.
5:1S:1S
0:00:60
Quick test: Press Measure button ( ) at the main display, the analyzer will
If the test strip is placed enter the countdown display. In this measuring waiting display, press and
d incorrectly 29/09/2O IS 0 O
or the strip slides hold the Measure button ( ) for 2 seconds, the analyzer will skip the
during O 8
measurement, the analyzer will countdown and start the test immediately.
report an error. The error code 016
Note:
displays
will
on screen; and the analyzer We do not recommend the user to perform a quick test for fully
give a long "beep" sound. react the sample solution with the test strip. The quick test is limited to
test strips that have been wetted and placed for 1 minute in air.

6:22:36

12 13
3.5 Review Measurements 2. Upload measurements to PC or inteligert terminas va Situeoc
At main display,press the Direction button (<, >) to view the previous (Optional)
results one by one. Press and hold the Direction button ( , >) to view the 1) At main display, press Setup button ()eeærhe seuc seen

results quickly. 2) Using direction button ( <, >) to seiect meru 'SET SU. s s o u n
At review measurements display below.
Press button to return to the main display.
Press Measure button ( ) to start another test.

3.6 Upload Measurements

The analyzer can upload the measurements to the desired device. The
upload function needs software support; please contact our service
personnel for details.
Two ways can be used to upload the measurements, follow the below
description.
1. Upload measurements to PC through the USB cable
3) Press Measure button (O,0 fashes
1) At main display, press Setup button (O) to enter the setup screen.
2) Using Direction button ( <, ) to select menu "SET USB" as shown 4) Press direction button ( <), 0 igs on the sceen. Press esure
below. button ( again to confirm cpen the Situetmcch functio
201 10/20 1s 5) Press buttonto return to main dispia
SEE USb 6) Run the software in PC or inteiligent temira (mth Suetoth asace)
and seardh the matched Biuetocth cesice Select he m a r h
Bluetooth device and connect it ycu can
upicad heequires
measurements to PC or inteiligent terminai anen comeciom s
successful.

NOTE:
U s e only the Us8 catle supeied or specfied by cur coman
09:4 : 9 When set the Us8 connecion, press irection u m ( ? iges a
3) then press Measure button d o e UsS comecteon
Press Measure button (),* flashes.
4) Press When set the Bhuetoath fanction, press directiorn u n ) iges ani
Direction
button ( <), lights on the screen. Press Measure
button () again to confirm the USB connection.
then press Measure buton
( dose
Suetmh camectic
Any questions about Usa and Biuetocth semins piease cavae c s g a
5) Press button to return tomain display. service personne
6) Connect the analyzer to PC with USB cable;run the software in PC, you
can upload the required measurements to PC after finishing the
connection settings.

15
14
3.7 Delete Measurements 3. Press Measure button (), the year numeric flashes.
1 At main display, press Setup button ( ) to enter the setup screen. 4. Using Direction button ( , >) tosetyear numeric, and then press
2 Using Direction button(<, >) to select menu "DEL DAT", as shown Measure button ( ) to confirm, the cursor skip to month numeric,
below the month numeric flashes.
5. Refer to step 4 to set the month, date, hour, minute and second in
dEL
turn.
6. Press Power button () to confirm the setting and return to the main

display.

3.9 Adjust Sensitivity

1. At main display, press Setup button (O) to enter the setup screen.
2. Using Direction button ( <, >) to select menu "SET SEN", as shown
O0:00: 8
below.
22109/20 16 0 a

Press Measure button (O), the screen flashes, and sound "Beep", SEE SEM

"Beep" will be heard.

4 Press Measure button ( ) to confirm the operation, "GOoD" displays
on the screen, it means the measurements are deleted successfully.

NOTE:
f the deletion is failed, the screen displays "FAIL"
If no results in analyzer, the screen displays "null".
Operate deletion with caution because this operation will delete all IS:S0:20
measurements stored in analyzer.
3. Press Measure button ) to choose the detection item, for example
3.8 Date and Time Setting LEU
1 At main display, press Setup button (O) to enter the setup screen. 22109120 16 0 a
2. SEE 000
Using Direction button (K,>) to select menu "SET TIE", as shown
below. LEU
209/20 1s 0.<
SEE

IS:S0:25
4 Using Direction button ( <, >) to adjust sensitivity value, and then
press Power button ( C) to confirm the setting and return to the main
ISS022
17
16
 display. 4 Care and Cleaning
NOTE:
tis
recommended tousethe sensitivity adjustment function when the full
quality control fluid test data is accumulated. Use only the substances approved by us and methods listed in this chapter
Any questions about sensitivity adjustment please contact Kongsung or service to clean or disinfect your equipment. Warranty does not cover damage
personnel caused by unapproved substances or methods.

4.1 Cleaning Analyzer

3.10 Factory Setting 1 Turn the analyzer off.
1. At main display, press Setup button ( ) to enter the setup Clean the display screen and shell using a soft, clean cloth dampened
screen. 2.
2 Using Direction button (<, >) to select menu "FAT SET". with neutral cleaning solution.
3 Wipe off all the cleaning solution with a dry cloth after cleaning if
SEE
necessary
4 Dry the analyzer in a ventilated, cool place.

To avoid damage to the analyzer, follow these rules:

Do not immerse the analyzer into liquid.
Do not pour liquid ontothe analyzer or accessories.
Do not allow liquid to enter the case.
Never use abrasive materials (such as steel wool or silver polish)
19S0-20
3 Press Measure button () to confirm selection. "FAT SET" changes to
"-FES after hearing sound "Beep, Beep". 4.2 Cleaning Test Strip Holder
4. Press Measure button ()again to confirm, the analyzer will turn off Turn the analyzer on and the holder completely slide out.
and reset to factory settings. Grasp the analyzer by left hand and pull out the holder with right
hand.
Press Power button (O) before pressing the Measure button to cancel the
operation.

3.11 Software Upgrade

Connect the analyzer to the PC through the USB cable; you can upgrade the
analyzer's software by upgrading the software code. Contact our service 3. Wipe the holder using a soft, clean cloth dampened with neutra
personnel for upgrading details. cleaning solution. Do not clean the standard reference pad.

Standard reference
pad

18 19
Wipe the holder notch using a cotton swad dampened with akohol 5Warranty and Service
and remave the dirt in noteh.

5.1 Warranty
The analyzer is covered by a comprehensive warranty for 12 months from
the date of production. However, damage occurring under the following
conditions shall not be covered by this warranty
Man-made damage or damage caused by improper use.
5 Install the hoider into analyzer aitercieaning Damage caused by mishandling during shipment.
Damage caused by uncontrollable natural factors such as arthquake,
fire or war.
Environment in which the analyzer is used does not meet the
requirements indicated in this manual.
Damage caused by use of an unspecified power supply or any other
abnormality in the power supply.
T u m the analyrer of Damage caused as a result of maintenance performed by personnel
not authorized by the manufacturer.
NOTE: Malfunction of the analyzer whose serial number is not legible
Keeo the woriing enironment and the analyzer suface dean and do not
damage the sareen
enough
Malfunction not caused by the analyzer itself.
The aicohol gasoline, berzene organic sohet cieaning are forbidden to use,
these tests wmake the anayzer deformation or pait removed and affect the
periormane r aPpearance To protect your rights, please keep the evidence, such as invoices,
Cean the tet strip hoider after usg eey daay receipts and so on well and fill in the warranty card and post it to the
Do nct cortaminate ar damage the coior bioci when cdeaning the strip holder. manufacturers. The manufacturer will repair or replace the analyzer for
Any service of this analyzer can only be performed by an authorized senvie free during its warranty period and any damage caused by non-human
engineer. Do not maintain and disassembly the analyaer. f amy quaity problems
factors
ocaur, piease cal our astoner senie
To keep the srip hoider deaning remove the urine residue in time, the
cress-cortamination wl affect the acnracy of the test resuts 5.2 Service
f any questions in equipment operation, please contact the manufacturer
or local agency.

4.3 Disposal of Waste

Customer Service Department
Discard used samples, strigs and protective gioves in acordance with local
regulations on disposal of bio-hazard waste. Jiangsu Accuracy Biotechnology Co., Ltd.
Address: NO.8, Shengchang West Road, Danyang Development Zone,
The analyzer should be disposed in accordance with local standards for the Jiangsu Province, 212300, P.R.China
Tel: 00S6 25 83681231-606
disposai of electronic waste after the expinry of the analyzer's life.
E-mail: [email protected]
Website: https://www.accuracybio-js.com

20 21
6 Accessory 7 Troubleshooting
NOTE: Some common troubles will occur during the operation of analyzer. Follow
Use the special strips provided by Accuracy in order to ensure the accuracy of the the below description to solve the troubles.
test results.
Use only the data cable and power adapter supplied or specified by Accuracy.
Strip is single use, do not reuse. Symptoms Potential Causes Solution
The analyzer Battery is low and no Check the battery, and charge the
Accessory name/Model Quantity Remarks cannot turn AC power is battery if the battery capacity is

Power adapter Stanadard configuration on. connected. empty. If the analyzer cannot turn
pcs
on, contact our service personnel.
Test strip 1 bottle Single use
Press the Test strip holder is Replace a new strip holder.
USB data cable 1 pcs Stanadard configuration Measure damaged.
Bluetooth thermal printer 1 pcs Optional button after The strip holder is Disassembly the holder and clean
loading strip installed in wrong it, check its transmission teeth
well, the and then reinstall the holder to
place or there is
analyzer object obstruction. analyzer. Restart the analyzer.
cannot start Contact our service personnel if
measure the trouble still exits.
after 60
Analyzer is damaged. Replace a new analyzer.
seconds
Battery is low and no Connect to the AC power supply
AC power is to charge battery and make a new

connected. measurement.

Strip is expired. Replace new strip within the

validity period.
Cannot detect the Reinstall the holder and restart
ERR 001
strip holder. the analyzer.
Calibration reference Clean the reference pad with
ERR 002
pad detection error alcohol.

The strip is placed Take a new strip for testing.

ERR 016 incorrectly or slides
during the testing.
ERR 017 Strip type is wrong. Replace the matched strip.

22 23
S Electromagnetic Compatibility A Product Specifications

1 The equipment complies with the electromagnetic compatibility A.1Analyzer Type

requirements specified in IEC61326-1-2012 and IEC Electric shock protection Class ll equipment and internal
61326-2-6:2012. The equipment complies with the emission and powered equipment
immunity requirements speafied in ISO/EC 15608-2.
The manufacturer shouid provide EMC infomation to the Degree of protection against liquid IPX1
customer or user. The user should ensure that the equipment is in Operation mode Continuous
an electromagnetic compstibility environment and that the
equipment is functioning property Intended service life 5 years
t is recommended to evaluate the electromagnetic environment
before using the equipment. Do not use the equipment near
strong radiation sources. Doing so may affect the equipment's A.2 Configuration and Physical Specifications
normal operation. Model Configuration Dimensions Weight
t may cause damaging electrostatic discharge, and resuiting in 11-tem measurement,
inaccurate test resuts when using the eçuipment in a dry HCUO1with US8, BLU and
environment, espeoally in a dny environnent with artificial indicators 111mm69mmu28mm Main unit:
materials (such as artificial fabrics, carpets, ete).
14-item measurement, (LxWxH) about 172g
The equipment is designed and tested according to dass A
equipment of EN 300328, EN 301489-1-17, EN 62479. The HCUOZ with US8, BLU and
equipment may cause radio interference, protective measures are indicators
required when using in home.
A.3 Environmental Specifications
Operating emvironment Temperature: 5'C- 35°C;
Relative humidity: s30%RH;
Atmospheric Pressure: 70kPa-106kPa

Storage and Temperature: -20°C- 55'C:

transportation Relative humidity: s85*%RH;
emvironment Atmospheric Pressure: 70kPa-106kPa

A.4 Technical Specifications

Detection principle Reflectance spectrometry colorimetricmethod
Stability The coefficient of variation of reflectance test
results (CV,<) S10 within 8 hours of starting up

Storage Can store 1000 results

24 25
 Throughput 240 tests/hour in fast mode, 60 tests/hour in 8.0 8.0 8.0
normal mode 8.5 8.5 8.5

Interfaces Micro USB interface: charge the built-in battery Blood Ocells/ul Ocells/ul
or connect the data cable for data transmission. (BLD) 10cells/uL 10cells/u
25cells/uL 25cells/ul +1
Display LCD display
+2
80cells/u 80cells/ul
Button 5 buttons +3
250cells/uL 250cells/ul
Power supply DC 5Vt10%: Specific gravity 1.000 1.000 1.000
AC 100V-240V+10%. 20VA, 50/60Hz (SG) 1.005 1.005 1.005
1.010 1.010 1.010

Reference Range 1.015 1.015 1.015

Test Items Traditional International Analyzer Display 1.020 1.020 1.020
1.025 1.025 1.025
Leucocytes Ocells/ul Ocells/uL
1.030 1.030
(LEU) 15cells/uL 15cells/uL 1.030

70cells/ul 70cells/ul +1 Ketones Omg/dL Ommol/L

125cells/u 125cells/uL +2 (KET) Smg/dL 0.5mmol/L
500cells/ul 500cells/uL +3 15mg/dl 1.5mmol/L
Nitrite 40mg/dl 4.0mmol/L
8.0mmol/L +3
(NIT) 80mg/dL
+4
Urobilinogen 0.2mg/dL 3.2umol/L
160mg/dL 16.0mmol/L
(UBG) Bilirubine Omg/dL Oumol/L
1mg/dL 16umol/L
(BIL) 1mg/dL 17umol/L
2mg/dL 32umol/L +1
2
4mg/dl 64umol/L +2 3mg/dL 50umol/L
+3
8mg/dL 128umol/L +3 6mg/dL 100umol/L
Protein Omg/dL Og/L
Glucose Omg/dL Ommol/L
(PRO) (GLU) 100mg/dl 5mmol/L
15mg/dL 0.15g/L
250mg/dL 15mmol/L
30mg/dL 0.3g/L +1
2
500mg/dL 30mmol/
100mg/dL 1.0g/L +2
+3
300mg/dL 3.0g/L 1000mg/dL 60mmol/L
+4
>2000mg/dL >20.0g/L +4 >2000mg/dl 110mmol/
Vitamin C Omg/dL Ommol/L
pH value 5.0 5.0 5.0
(VC) 10mg/dl 0.6mmol/L 1
6.0 6.0 6.0 2
6.5 6.5 6.5 25mg/dl 1.4mmol/L
3
5Omg/dL 2.8mmol/L
7.0 7.0 7.0
7.5 7.5 7.5 Calcium Ommol/L Ommol/L

26 27
 2.5mmol/L 2.5mmol/L B Symbols and Abbreviation
5.0mmol/L 5.0mmol/l +2
10.0mmolL 10.0mmol/L +3 B.1 Units
Creatinine 0.9mmol/L 0.9mmol/L Abbreviation English
(C) 4,4mmol/L 4.4mmol/L +1 ul(uL) microliter
17.7mmol/L 17.7mmol/L +2 Lumol micromole
26.5mmol/L 26.5mmol/ A
ampere
Wicroalbumin Omg/L Omg/L C centigrade
(1MA) Cm centimeter
30mg/L 30mg/L
cells
80mg/L 80mg/L +2 cells
150mg/L 150mg/L +3
dl(dL) deciliter
gram
h
hour
Hz |hertz
L liter
milligram
mi
milliliter
mm
millimeteer
mmol millimole
second
V
volt
|W watt
B.2 Symbols
Symbols English
negative
percent
per; divide; or
to

positive
greater than or equal to
copyright

28 29
B.3 Terms
English Abbr. Full name

AC Alternating current

Ca Calcium

Cr Creatinine

DC Direct current

TEMP Temperature

USB Universal serial bus

International Electrotechnical Commission
IEC
Institute of Electrical and Electronic Engineers
IEEE
LEU Leucocytes
Microalbumin
MA
NIT Nitrite

UBG Urobilinogen
PRO Protein

pH Potential of Hydrogen

BLD Blood

SG Specific Gravity
KET Ketones
BIL Bilirubine
GLU Glucose
VC Vitamin C

30