LCD Alphanumeric Codepad (Menu Programming)

Solution 2000/3000

Master Code Default [2][5][8][0] Installer Code Default [1][2][3][4]

1 Show Fault/Trouble
Condition 2 Default the Panel 3 Set the System
Time & Date
• Main screen > press & hold [5] • Remove power (PSU & battery). • Main screen > Master Code
• Use arrows to scroll & [-] to exit • Press & hold DEFAULT button then [6][#]
on PCB for 5 secs while • Enter Date & Time using
reconnecting power number keys
• [#] to save or [*] to exit

6 Program Zone Type 5 Enter Installer Menu &

Change Installer Code 4 Change the
Master Code
• Installer Code then [-] • Installer Code then [-] • Master Code then [-]
• Select Menu [4][1] (Zone • Select Menu [2][1] (Installer • Select Menu [2][2] (User
Config) Code) Code). [#] to select U01 –
• Select zone number > scroll • Enter new Installer Code, [#] User 01 Name
with arrows or enter zone • Press [-] until ‘Confirm to Save • Enter new Master Code, [#]
number, then [#] Parameter Changes’ appears • Press [-] until ‘Confirm to
• Select zone type > scroll with then [#] Save Parameter Changes’
arrows or enter zone type, appears then [#]
then [#]
• Repeat for other zones.
• Press [-] until ‘Confirm to
Save Parameter Changes’ Common Zone Types
appears then [#] 0 – Instant; 1 – Handover; 2 – Delay 1; 3 – Delay 2; 11 – Keyswitch;
12 – 24hr Burglary; 14 – Chime Only; 15 – Not Used

7 Program First
Receiver
8 Program Second
Receiver 9 Program System
Account Code
• Installer Code then [-] • Installer Code then [-] • Installer Code then [-]
• Select Menu [7][1][1] (First • Select Menu [7][1][2] • Select Menu [7][1][4]
Phone Number) (Second Phone Number) (Subscriber ID Number)
• [#] to select Receiver 1 • [#] to select Receiver 1 • [#] to select Receiver 1
• Enter phone number using • Enter phone number using • Enter account code using
number keys, then [#] number keys, then [#] number keys, then [#]
• Press [-] until ‘Confirm to Save • Press [-] until ‘Confirm to • Press [-] until ‘Confirm to
Parameter Changes’ appears Save Parameter Changes’ Save Parameter Changes’
then [#] appears then [#] appears then [#]

Communicator Format Types 10 Program Communicator Format

0 – Not Used 6 - SIA Fast • Installer Code then [-]

1 – Contact ID 7 - SIA Slow • Select Menu [7][1][3] (Transmit Format)
4 – Domestic Dial • [#] to select Receiver 1
8 – CSV-IP • Select format > scroll with arrows or enter format type then [#]
9 – Email • Press [-] until ‘Confirm to Save Parameter Changes’ appears
then [#]
11 Program Open/
Close Report 12 Program Entry
Time 13 Program Exit
Time
• Installer Code then [-] • Installer Code then [-] • Installer Code then [-]
• Select Menu [7][3][4] (Arm/ • Select Menu [3][1][1] (Entry • Select Menu [3][1][3]
Disarm Report Option) Time 1) (Exit Time)
• To enable open/close report, • Enter the time in seconds • Enter the time in seconds
select Receiver 1 using using the number keys then using the number keys
arrows or press [1]; then [#] press [#] then press [#]
• To disable open/close report, • Press [-] until ‘Confirm to • Press [-] until ‘Confirm to
select No Report using arrows Save Parameter Changes’ Save Parameter Changes’
or press [0]; then [#] appears then press [#] appears then press [#]
• Press [-] until ‘Confirm to
Save Parameter Changes’
appears then press [#]

Program User Program Additional

15 Codes 14 Timers

16 Perform Walk Test • Master Code then [-]

• Select Menu [2][2] (User
• Installer Code then [-]
• Select Menu [3][1] (Timer)
• Main screen > enter Installer Code) • Select timer function such as
Code then [7][#] • Use arrow keys to select the [8] Auto Arm Time & [9] Auto
• Zones will tick one by one user or enter user number, Disarm Time
as they are activated. Scroll then press [#] • Enter the time using the
using the arrows • Enter new user code, then [#] number keys (eg 20 Hour, 00
• Press [-] to exit walk test • Press [-] until ‘Confirm to Save Min) then press [#]
mode Parameter Changes’ appears • Press [-] until ‘Confirm to
then press [#] Save Parameter Changes’
appears then press [#]

17 Learn in a
Wireless Device 18 Delete a Wireless

• Main screen > enter Installer

Device
• Main screen > enter Installer
19 Learn in a
Wireless Keyfob
Code then [0][#] Code then [0][#] • Main screen > enter Master
• Enter device/zone number • Enter device/zone number Code then [1][#]
using the number keys then using the number keys then • Enter keyfob/user number
press [#] press [#] using the number keys then
• Enter the device RFID number • Press [*] to delete the device press [#]
as printed on the device then
• Select RF keyfob then [#]
press [#] OR just press [*]
• Enter the device RFID number
to enter auto-learn mode,
Both the RADION Wireless as printed on the device then
tamper the device to learn,
Receiver or WE800EV2 Keyfob press [#] OR just press [*] to
then press [#] to save
receiver must be enabled in enter auto-learn mode, press
• Enter the RF Zone option
programming before learning a button on the keyfob to
0 = not used
keyfobs or wireless devices. learn, then press [#] to save
1 = PIR/reed with magnet
• Press [#] to save the new
2 = external contact reed
keyfob.
• Press [#]

20 Delete a Wireless Keyfob

• Main screen > enter Master Code then [1][#]
• Select RF keyfob then [#]
• Enter keyfob/user number using the number keys then press [#]
• Press [*] to delete the keyfob then [#] to exit from the user and
then [-] to exit

Copyright © 2015 — In the interest of ongoing product improvement we reserve the right to change specifications at any time without notice — E&OE 09/15