-|Transparent Guide|-

TCD210240AD Safety Considerations

• Observe all ‘Safety Considerations’ for safe and proper operation to avoid hazards.
• ᜸ symbol indicates caution due to special circumstances in which hazards may occur.

Simultaneous
᜸ Warning Failure to follow instructions may result in serious injury or death

01. Fail-safe device must be installed when using the unit with machinery that

Heating&Cooling Output PID

may cause serious injury or substantial economic loss.(e.g. nuclear power
control, medical equipment, ships, vehicles, railways, aircraft, combustion
apparatus, safety equipment, crime/disaster prevention devices, etc.)
Failure to follow this instruction may result in personal injury, economic loss or fire.

Temperature Controllers
02. Do not use the unit in the place where flammable/explosive/corrosive gas,
high humidity, direct sunlight, radiant heat, vibration, impact or salinity
may be present.
Failure to follow this instruction may result in explosion or fire.
03. Install on a device panel to use.
Failure to follow this instruction may result in electric shock.
04. Do not connect, repair, or inspect the unit while connected to a power
source.
Failure to follow this instruction may result in fire or electric shock.
05. Check ‘Connections’ before wiring.
Failure to follow this instruction may result in fire.
06. Do not disassemble or modify the unit.
Failure to follow this instruction may result in fire or electric shock.

᜸ Caution Failure to follow instructions may result in injury or product damage

01. When connecting the power input and relay output, use AWG 20 (0.50 mm2)
cable or over, and tighten the terminal screw with a tightening torque of 0.74
to 0.90 N m.
When connecting the sensor input and communication cable without
dedicated cable, use AWG 28 to 16 cable and tighten the terminal screw with
a tightening torque of 0.74 to 0.90 N m.
Failure to follow this instruction may result in fire or malfunction due to contact
failure.
02. Use the unit within the rated specifications.
Failure to follow this instruction may result in fire or product damage
03. Use a dry cloth to clean the unit, and do not use water or organic solvent.
Failure to follow this instruction may result in fire or electric shock.
04. Keep the product away from metal chip, dust, and wire residue which flow
into the unit.
Failure to follow this instruction may result in fire or product damage.

Cautions during Use

TK Series • Follow instructions in ‘Cautions during Use’. Otherwise, it may cause unexpected

PRODUCT MANUAL
accidents.
• Check the polarity of the terminals before wiring the temperature sensor. For RTD
temperature sensor, wire it as 3-wire type, using cables in same thickness and length.
For thermocouple (TC) temperature sensor, use the designated compensation wire for
extending wire.
For your safety, read and follow the considerations written in the instruction • Keep away from high voltage lines or power lines to prevent inductive noise. In case
installing power line and input signal line closely, use line filter or varistor at power line
manual, other manuals and Autonics website. and shielded wire at input signal line. Do not use near the equipment which generates
The specifications, dimensions, etc are subject to change without notice for product strong magnetic force or high frequency noise.
improvement Some models may be discontinued without notice. • Do not apply excessive power when connecting or disconnecting the connectors of
the product.
• Install a power switch or circuit breaker in the easily accessible place for supplying or
disconnecting the power.
• Do not use the unit for other purpose (e.g. voltmeter, ammeter), but temperature
controller.
Features • When changing the input sensor, turn off the power first before changing. After
changing the input sensor, modify the value of the corresponding parameter.
• 50ms high-speed sampling rate and ±0.3% display accuracy
• Simultaneous heating and cooling control function (patent) *
• Switch between current output and SSR drive output
• SSR drive output (SSRP function) control options : ON/OFF control, cycle control,
phase control
• Communication output models available : RS485 (Modbus RTU)
• Parameter configuration via PC (RS485 communication)
- DAQMaster software included (comprehensive device management software)
-C ommunication converter sold separately : SCM-US (USB to serial converter), SCM-
38I (RS-232C to RS485 converter), SCM-US48I (USB to RS485 converter)
• User-friendly parameter features
• Heater disconnect alarm function (CT input)
- Current transformer (CT) sold separately : CSTC-E80LN, CSTC-E200LN, CSTS-E80PP
• SV preset function (up to 4 set values) using digital input terminals
• Available in various DIN sizes : (48×24, 48×48, 72×72, 96×48, 48×96, 96×96 mm)
*Korea Patent Registration 10-1002582, U.S.A. Patent Registration 8645000, Japan Patent Registration 3184816,
China Patent Registration ZL200980111733.X, Vietnam Patent Registration 1-0012131, India Patent Registration
291573, Indonesia Patent Registration IDP0032166

ᜢ᜽ᜧᜫ
-|Transparent Guide|-

• 24 VACᜠ, 24-48 VDCᜡ power supply should be insulated and limited voltage/current or
Class 2, SELV power supply device. Sold Separately
• Do not overlapping communication line and power line. Use twisted pair wire for
communication line and connect ferrite bead at each end of line to reduce the effect of • Current transformer (CT) • 11-pin controller socket: PG-11, PS-11 (N)
external noise. • Terminal protection cover: RSA / RMA / RHA / RLA-Cover
• Make a required space around the unit for radiation of heat. For accurate temperature
measurement, warm up the unit over 20 min after turning on the power. • Communication Converter: SCM-US / SCM-38I / SCM-US48I / SCM-WF48
• Make sure that power supply voltage reaches to the rated voltage within 2 sec after
supplying power.
• Do not wire to terminals which are not used. Specifications
• This unit may be used in the following environments.
- Indoors (in the environment condition rated in ‘Specifications’) Series TK4N TK4SP TK4S TK4M
- Altitude Max. 2,000 m Power AC type 100 - 240 VACᜠ 50/60 Hz
- Pollution degree 2 supply AC/DC type - 24 VACᜠ 50/60 Hz, 24-48 VDCᜡ
- Installation category II Permissible voltage
90 to 110 % of rated voltage
range
Power AC type ≤ 6 VA ≤ 8 VA
Ordering Information consumption AC/DC type - AC: ≤ 8 VA, DC ≤ 5W
≈ 70 g ≈ 85 g ≈ 105 g ≈ 140 g
Unit weight (packaged)
This is only for reference, the actual product does not support all combinations. (≈ 140 g) (≈ 130 g) (≈ 150 g) (≈ 210 g)
For selecting the specified model, follow the Autonics website . Series TK4W TK4H TK4L
Power AC type 100 - 240 VACᜠ 50/60 Hz
T K ❶ ❷ - ❸ ❹ ❺ ❻ supply AC/DC type 24 VACᜠ 50/60 Hz, 24-48 VDCᜡ
Permissible voltage
90 to 110 % of rated voltage
range
❶ Digit ❹ Power supply
Power AC type ≤ 8 VA
4: 4 digit 2: 24 VACᜠ 50/60 Hz, 24-48 VDCᜡ
consumption AC/DC type AC: ≤ 8 VA, DC ≤ 5W
4: 100-240 VACᜠ 50/60 Hz Unit weight (packaged) ≈ 141 g (≈ 211 g) ≈ 141 g (≈ 211 g) ≈ 198 g (≈ 294 g)
❷ Size ❺ OUT1 Control output
Sampling period 50 ms
N: DIN W 48 × H 24 mm R: Relay Input specification Refer to 'Input Type and Using Range'
SP: DIN W 48 × H 48 mm (11 pin plug type) S: SSR drive • 0.0-50.0 A (primary current measurement range)
S: DIN W 48 × H 48 mm C: Selectable current or SSR drive CT input • CT ratio: 1/1,000
Option • Measurement accuracy: ±5% F.S. ±1digit
M: DIN W 72 × H 72 mm output
input • Contact - ON: ≤ 2 kΩ, OFF: ≥ 90 kΩ
W: DIN W 96 × H 48 mm Digital input • Non contact - residual voltage ≤ 1.0 V, leakage current ≤ 0.1 mA
H: DIN W 48 × H 96 mm • Outflow current: ≈ 0.5 mA per input
L: DIN W 96 × H 96 mm Relay 250 VACᜠ 3 A, 30 VDCᜡ 3 A 1a
Control
SSR 11 VDCᜡ±2 V, ≤ 20 mA
❸ Option in/output ❻ OUT2 Control output output
Current DC 4-20 mA or DC 0-20 mA (parameter), Load resistance: ≤ 500 Ω
Size: N N: Normal type Alarm
Relay
AL1, AL2: 250 VACᜠ 3 A 1a
[No OUT2 (Heating or Cooling)] output • TK4N AL2: 250 VACᜠ 0.5 A 1a (≤ 125 VA)
PN OUT2 Function
DC 4 - 20 mA (Load resistance: ≤ 500 Ω, Output accuracy: ±0.3%
Normal type 01) Alarm 1 + CT input R: Heating & Cooling type Option Transmission
1 F.S.)
output
Heating & Cooling Alarm 2 [Relay output] 03) RS485 comm. Modbus RTU
2 Normal type Alarm 1 + Alarm 2 C: Heating & Cooling type Display type 7 segment (red, green, yellow), LED type
Normal type Alarm 1 + Digital input 1/2 [Selectable current or SSR drive Heating, Cooling
D Control
Heating & Cooling Digital input 1/2 output] 04) Heating & ON/OFF, P, PI, PD, PID Control
type
Alarm 1+Transmission Cooling
Normal type • Thermocouple, RTD: 1 to 100 (0.1 to 100.0) ℃/℉
R output Hysteresis
Heating & Cooling Transmission output • Analog: 1 to 100 digit
Proportional band (P) 0.1 to 999.9 ℃/℉ (0.1 to 999.9%)
Alarm output 1 + RS485
Normal type Integral time (I) 0 to 9,999 sec
T communication
Derivative time (D) 0 to 9,999 sec
Heating & Cooling RS485 communication
• Relay output, SSR drive output: 0.1 to 120.0 sec
Control cycle (T)
Size: SP • Selectable current or SSR drive output: 1.0 to 120.0 sec
PN Function Manual reset 0.0 to 100.0%
OUT1/2: ≥ 5,000,000 operations
1 Alarm 1 Relay
Mechanical AL1/2: ≥ 20,000,000 operations (TK4H/W/L: ≥ 5,000,000
life
Size: S, M, W, H, L operations)
cycle
PN Function Electrical ≥ 100,000 operations
Dielectric strength Dependent on the power supply
1 Alarm 1
Between the charging part and the case: 3,000 VAC ~ 50/60 Hz
2 Alarm 1 + Alarm output 2 AC voltage type
for 1 minute
R Alarm 1 + Transmission output Between the charging part and the case: 2,000 VAC ~ 50/60 Hz
AC / DC voltage type
T Alarm 1 + RS485 communication for 1 minute
A Alarm 1 + Alarm 2 + Transmission output 0.75 mm amplitude at frequency of 5 to 55 Hz in each X, Y, Z
Vibration
direction for 2 hours
B Alarm 1 + Alarm 2 + RS485 communication
Insulation resistance ≥ 100 MΩ (500 VDCᜡ megger)
D Alarm 1 + Alarm 2 + Digital input 1/2 02)
±2 kV square shaped noise by noise simulator (pulse width: 1 ㎲)
Noise immunity
01) The CT input model of TK4N can be selected only in the normal type model with alarm output 1. (except R-phase, S-phase
TK4SP) Memory retention ≈ 10 years (non-volatile semiconductor memory type)
02) Only for TK4S-D, OUT2 output terminal is used as DI-2 input terminal. Ambient temperature -10 to 50 ℃, storage: -20 to 60 ℃ (no freezing or condensation)
03) When operating mode is heating or cooling control, OUT2 can be used as alarm output 3 (except TK4N).
Ambient humidity 35 to 85%RH, storage: 35 to 85%RH (no freezing or condensation)
04) When operating mode is heating or cooling control, OUT2 can be used as transmission output 2.
IP65 (Front panel, IEC standards)
Protection structure
• TK4SP: IP50 (Front panel, IEC standards)
Double insulation or reinforced insulation (mark: ▱, dielectric
Product Components Insulation type strength between the measuring input part and the power part: 2
kV)
• Product (+ bracket) • Instruction manual Certification ᜢ᜽ᜧᜫ
• [TK4N] Terminal protection cover × 1

Communication Interface
Manual
■ RS485
For proper use of the product, refer to the manuals and be sure to follow the safety Comm. protocol Modbus RTU
considerations in the manuals. Connection type RS485
Download the manuals from the Autonics website. Application standard EIA RS485 compliance with
Maximum connection 31 units (address: 01 to 99)
Synchronous method Asynchronous
Software Comm. Method Two-wire half duplex
Comm. effective range ≤ 800 m
Comm. speed 2,400 / 4,800 / 9,600 (default) / 19,200 / 38,400 bps (parameter)
Download the installation file and the manuals from the Autonics website.
Response time 5 to 99 ms (default: 20 ms)
■ DAQMaster Start bit 1 bit (fixed)
DAQMaster is comprehensive device management program. It is available for Data bit 8 bit (fixed)
Parity bit None (default), Odd, Even
parameter setting, monitoring.
Stop bit 1 bit, 2 bit (default)
EEPROM life cycle ≈ 1,000,000 operations (Erase / Write)
-|Transparent Guide|-

Input Type and Using Range Dimensions

The setting range of some parameters is limited when using the decimal point display. • Unit: mm, For the detailed drawings, follow the Autonics website.
Decimal • Below is based on TK4S Series.
Input type Display Using range (℃) Using range (℉)
point
1 -200 to 1,350 -328 to 2,462 A C D ■ Panel cut-out
K (CA)
KCaH
0.1 -199.9 to 999.9 -199.9 to 999.9 G
E
KCaL
1 -200 to 800 -328 to 1,472
J (IC)
JIcH
0.1 JIcL -199.9 to 800.0 -199.9 to 999.9
1 -200 to 800 -328 to 1,472

J
E (CR)
ECrH
0.1 ECrL -199.9 to 800.0 -199.9 to 999.9 I

H
1 -200 to 400 -328 to 752
T (CC)

F
TCcH
0.1 TCcL -199.9 to 400.0 -199.9 to 752.0
B (PR) 1 0 to 1,800 32 to 3,272
 hermo
T
B PR
-couple R (PR) 1 R PR 0 to 1,750 32 to 3,182
S (PR) 1 0 to 1,750 32 to 3,182
Body Panel cut-out
S PR
N (NN) 1 N NN -200 to 1,300 -328 to 2,372
C (TT) 01) 1 C TT 0 to 2,300 32 to 4,172 A B C D E F G H I J
G (TT) 02) 1 G TT 0 to 2,300 32 to 4,172 TK4N 48 24 3 91.8 - 21.8 ≥ 55 ≥ 37 45+00.6 22.2+00.3
1 -200 to 900 -328 to 1,652
L (IC) TK4S 48 48 6 64.5 1.7 45 ≥ 65 ≥ 65 45+00.6 45+00.6
LIcH
0.1 -199.9 to 900.0 -199.9 to 999.9
TK4SP 48 48 6 72.2 - 44.8 ≥ 65 ≥ 65 45+00.6 45+00.6
LIcL
1 -200 to 400 -328 to 752
U (CC)
UCcH
0.1 UCcL -199.9 to 400.0 -199.9 to 752.0 TK4M 72 72 6 64.5 1.7 67.5 ≥ 90 ≥ 90 68+00.7 68+00.7
Platinel II 1 PLII 0 to 1,390 32 to 2,534 TK4W 96 48 6 64.5 1.5 44.7 ≥ 115 ≥ 65 92+00.8 45+00.6
Cu50 Ω 0.1 -199.9 to 200.0 -199.9 to 392.0
TK4H 48 96 6 64.5 1.5 91.5 ≥ 65 ≥ 115 45+00.6 92+00.8
CU 5
Cu100 Ω 0.1 CU10 -199.9 to 200.0 -199.9 to 392.0
1 -200 to 650 -328 to 1,202 TK4L 96 96 6 64.5 1.5 91.5 ≥ 115 ≥ 115 92+00.8 92+00.8
JPt100 Ω
JPtH
0.1 -199.9 to 650.0 -199.9 to 999.9
■ Bracket
RTD
JPtL
DPt50 Ω 0.1 DPT5 -199.9 to 600.0 -199.9 to 999.9
1 -200 to 650 -328 to 1,202
DPt100 Ω
DPtH
TK4N TK4S/SP Other series
0.1 DPtL -199.9 to 650.0 -199.9 to 999.9
Nickel120 Ω 1 -80 to 200 -112 to 392 42 □49.5 30.5

3.3
NI12
0 to 10 V - AV1 0 to 10 V
0 to 5 V - AV2 0 to 5 V
1 to 5 V - 1 to 5 V 46

4
Analog
AV3

36.3
0 to 100 mV - 0 to 100 mV
28.8

22
AMV1
0 to 20 mA - 0 to 20 mA

37.5
40.5
AMA1
4 to 20 mA - AMA2 4 to 20 mA 45.2
01) C (TT): Same as existing W5 (TT) type sensor 48.6
32.4 12
02) G (TT): Same as existing W (TT) type sensor 26.4

3.5
23.9
• Permissible line resistance per line: ≤ 5 Ω

11.6
■ Display accuracy
Input type Using temperature Display accuracy
7.9 10 60.3
(PV ±0.3% or ±1 ℃ higher one) ±1-digit
• Thermocouple K, J, T, N, E below -100 ℃ and L, U, PLII, RTD Cu50 Ω, ■ Terminal protection cover
At room temperature DPt50 Ω: (PV ±0.3% or ±2 ℃ higher one) ±1-digit TK4N
(23℃ ±5 ℃) • Thermocouple C, G and R, S below 200 ℃:
Thermo (PV ±0.3% or ±3 ℃ higher one) ±1-digit 44.6 6.2
-couple • Thermocouple B below 400 ℃: There is no accuracy standards
RTD (PV ±0.5% or ±2 ℃ higher one) ±1-digit
21.8

• RTD Cu50 Ω, DPt50 Ω: (PV ±0.5% or ±3 ℃ higher one) ±1-digit

Out of room
• Thermocouple R, S, B, C, G:
temperature range
(PV ±0.5% or ±5 ℃ higher one) ±1-digit
• Other sensors: ≤ ±5 ℃ (≤-100 ℃)
At room temperature
±0.3% F.S. ±1-digit
Installation Method
(23℃ ±5 ℃)
Analog
Out of room
±0.5% F.S. ±1-digit
temperature range
• In case of TK4SP Series, ±1 ℃ will be added to the degree standard.
■ TK4N ■ Other series

Unit Descriptions
1. PV display part (Red)
• Run mode: Displays PV (Present value).
1 • Setting mode: Displays parameter name. Screwdriver
2. SV display part (Green) Flathead screwdriver
• Run mode: Displays SV (Setting value). After mounting the product to panel
4 • Setting mode: Displays parameter setting value.
with bracket, fasten the bolts by Insert the unit into a panel, fasten the bracket by
2 3. Input key
Display Name
using screwdriver. pushing with a flathead screwdriver.
[A/M] Control switching key
[MODE] Mode key
[◀], [▼], [▲] Setting value control key Errors
3
4. Indicator
TK4N Series Display Input Description Output Troubleshooting
Display Name Description
℃, %, ℉ Unit Displays selected unit (parameter) Flashes at 0.5 sec interval when 'Sensor error,
Temperature Check input
AT Auto tuning Flashes during auto tuning every 1 sec input sensor is disconnected or MV' parameter
sensor sensor status.
5 sensor is not connected. setting value
Turns ON when the control output is ON
• SSR output (cycle/phase control) 'Sensor error,
OPEN
Flashes at 0.5 sec interval when Check analog
Control MV over 5% ON Other series Analog MV' parameter
OUT1/2 input is over F.S. ±10%. input status.
output • Current output setting value
M
 anual control: 0% OFF, over ON Flashes at 0.5 sec intervals if the
Auto control: below 2% OFF, over 3% ON Temperature Heating: 0%,
input value is above the input
Alarm sensor Cooling: 100%
AL1/2 Turns ON when the alarm output is ON range.01)
output 5. PC loader port:
Flashes at 0.5 sec intervals if the
HHHH
Manual For connecting
MAN Turns ON during manual control communication Analog input value is over 5 to 10% of high Normal output When input is
control within the rated
converter (SCM series). limit or low limit value.
The SV indicator is ON which is currently input range,
SV1/2/3 Multi SV Flashes at 0.5 sec. intervals if the
displayed. (When using multi SV function) Temperature Heating: 100%, this display
input value is below the input disappears.
• For the details about old model, refer to the user manual. Download the manuals from the Autonics website. sensor Cooling: 0%
range.01)
Flashes at 0.5 sec intervals if the
LLLL

Analog input value is over 5 to 10% of low Normal output

limit or high limit value.
Temperature
Flashes at 0.5 sec intervals if there
sensor Check setting
is error for setting and it returns to -
method.
ERR
Analog the error-before screen.

01) Be careful that when HHHH / LLLL error occurs, the control output may occur by recognizing the
maximum or minimum input depending on the control type.
-|Transparent Guide|-

Connections ■ TK4H / W / L
• Shaded terminals are standard model. 1 13
• Digital input is not electrically insulated from internal circuits, so it should be insulated Digital Input
when connecting other circuits. 2 14 Contact,
Non contact Input
■ TK4N Transfer Output 3 AL1 OUT: 15
DC 4-20 mA 250 VACᜠ 3 A 1a DI-1 DI-1
3 +
S V 4 RESISTIVE LOAD 16 DI-2 DI-2
Communication S 4 -
Output
O R 5 AL2 OUT: 17
11 VDCᜡ±2V
250 VACᜠ 3 A 1a
CT Current Transformer U 20 mA Max.
RS485(A+)
RESISTIVE LOAD
mA 0.0-50.0 A T
3 6 18 + Transfer Out
1 C +
mA RS485(B-)
mA
DC 4-20 mA
V U - 7
OUT2: Relay
19
-
4 250 VACᜠ 3 A 1a
R Communication output
Digital Input 30 VDCᜡ 3 A 1a
TC R 11 VDCᜡ±2V
Contact, 20 mA Max. 8 RESISTIVE LOAD 20 Current
RTD Non contact Input CT Transformer
1 9
+ OUT1: Relay
21 0.0-50.0 A
S V 250 VACᜠ 3 A 1a
S 2 - 30 VDCᜡ 3 A 1a A
R 10 RESISTIVE LOAD 22
OUT2/AL1 OUT: OUT1: AL2 OUT: O 11 VDCᜡ±2V
250 VACᜠ 3 A 1a 250 VACᜠ 3 A 1a 250 VACᜠ 0.5 A 1a U 20 mA Max. B
30 VDCᜡ 3 A 1a 30 VDCᜡ 3 A 1a
RESISTIVE LOAD 11 23 mA
RESISTIVE LOAD RESISTIVE LOAD
T -
1 V
2 C + + B'
SOURCE U -
mA SOURCE 12 24 RTD TC
100-240 VACᜠ 2 100-240 VACᜠ 50/60 Hz 8 VA
50/60 Hz 6 VA R 24 VACᜠ 50/60 Hz 8 VA
R 11 VDCᜡ±2V 24-48 VDCᜡ 5 W
20 mA Max. OUT1 OUT2
SSR Current SSR Current
■ TK4S Digital Input
OUT2: Relay
250 VACᜠ 3 A 1a
Digital Input Contact, 30 VDCᜡ 3 A 1a 9 + 9 + 7 + 7 +
Contact, Non contact Input RESISTIVE LOAD V mA V mA
Non contact Input 10 - 10 - 8 - 8 -
1 13 7 AL1 OUT:
250 VACᜠ 3A 1a 11 VDCᜡ±2V DC 0/4-20 mA 11 VDCᜡ±2V DC 0/4-20 mA
DI-1 DI-1 DI-2 DI-2 20 mA Max. Load 500 Ω Max. 20 mA Max. Load 500 Ω Max.
2 14 8 RESISTIVE LOAD
AL2 OUT:
250 VACᜠ 3A 1a
OUT1:Relay 3 15 9 RESISTIVE LOAD
Crimp Terminal Specifications
RS485(A+)
250 VACᜠ 3 A 1a Transfer mA
30 VDCᜡ 3 A 1a Output A
RESISTIVE LOAD 4 DC 4-20 mA RS485(B-) 16 10
Communication • Unit: mm, Use the crimp terminal of follow shape.
B
5 Output 17 11 mA
- V
Current CT
+ B'
SOURCE 6 Transformer 18 12
100-240 VACᜠ 50/60 Hz 8 VA 0.0-50.0 A RTD TC
24 VACᜠ 50/60 Hz 8 VA ≥3.0 ≥3.0
≤5.8 ≤5.8
24-48 VDCᜡ 5 W
OUT1 OUT2
SSR Current SSR Current Fork crimp terminal Round crimp terminal
3 + 3 + 13 + 13 +
V mA V mA
4 - 4 - 14 - 14 -
Initial Display When Power is ON
11 VDCᜡ±2V DC 0/4-20 mA 11 VDCᜡ±2V DC 0/4-20 mA
20 mA Max. Load 500Ω Max. 20 mA Max. Load 500Ω Max.
When power is supplied, after all display will flash for 1 sec, model name is displayed
■ TK4SP OUT2: Relay sequentially. After input sensor type will flash twice, enter into RUN mode.
250 VACᜠ 3 A 1a
30 VDCᜡ 3 A 1a 3. Input
1. All display 2. Model 4. Run mode
6 RESISTIVE LOAD
specification
OUT1: Relay
250 VACᜠ 3 A 1a
5 7
AL1: PV display part ***8
30 VDCᜡ 3 A 1a
TK4 TK4 OPEN
RESISTIVE LOAD 4 8 Relay
SV display part ***8
250 VACᜠ 3 A 1a 14RN KCaH 0
RESISTIVE LOAD
B'
3 9
Mode Setting
V
B SOURCE
mA 2 10 100-240 VACᜠ 50/60 Hz 8 VA
TC -
A 1 11 +
24 VACᜠ 50/60 Hz 8 VA
24-48 VDCᜡ 5 W
RTD Auto before Password Key input Entering mode
entering to mode Password Pass Auto Selected mode
→
OUT1 OUT2 (when using input [◀], [▲], [▼] Password input
password) Fail
SSR Current SSR Current [MODE] Run mode
5 + 5 + 6 - 6 - Move digits: [◀] Save: [MODE]
V mA V mA [◀], [▲], [▼] → SV setting Change value: or no key input →
4 - 4 - 9 + 9 +
[▲], [▼] over 5 sec
11 VDCᜡ±2V DC 0/4-20 mA 11 VDCᜡ±2V DC 0/4-20 mA Parameter →
20 mA Max. Load 500 Ω Max. 20 mA Max. Load 500 Ω Max. RUN [MODE] over 2 sec → [MODE] over 3 sec
group
■ TK4M [◀] + [▲] + [▼] Parameter
→ Auto → RUN
1 AL1 OUT: 19 10 Digital Input
over 5 sec reset
250 VACᜠ 3 A 1a DI-1 DI-1
RESISTIVE LOAD Contact, Auto/Manual
2 AL2 OUT: 20 11 Non contact Input
[A/M] 01) → control [A/M] →
250 VACᜠ 3 A 1a RS485(A+) switching
3 RESISTIVE LOAD 21 12 +
mA Transfer Output [▲] + [▼] over 3 Digital input
RS485(B-) DC 4-20 mA → Auto →
4 OUT2: Relay 22 13 - sec key
250 VACᜠ 3 A 1a Communication output 01) In case of TK4N / 4S / 4SP model, short press of [MODE] key replaces [A/M] key function.
30 VDCᜡ 3 A 1a
5 RESISTIVE LOAD 23 14 Current
CT Transformer
6 OUT1: Relay 24 15
0.0-50.0 A
250 VACᜠ 3 A 1a
30 VDCᜡ 3 A 1a A
7 RESISTIVE LOAD 25 16 +
SOURCE B
8 100-240 VACᜠ 26 17 +
mA
- 50/60 Hz 8 VA V
+ 24 VACᜠ
9 50/60 Hz 8 VA 27 18 B'
RTD TC
- -
24-48 VDCᜡ 5 W

OUT1 OUT2
SSR Current SSR Current
6 + 6 + 4 + 4 +
V mA V mA
7 - 7 - 5 - 5 -

11 VDCᜡ±2V DC 0/4-20 mA 11 VDCᜡ±2V DC 0/4-20 mA

20 mA Max. Load 500 Ω Max. 20 mA Max. Load 500 Ω Max.
-|Transparent Guide|-

Parameter Setting Function: Alarm

• Some parameters are activated/deactivated depending on the model or setting of Set both alarm operation and alarm option by combining.
other parameters.
88* 8 Each alarm operates individually in two alarm output models.
Alarm Alarm When the current temperature is out of alarm range, alarm clears
• The 'Parameter mask' feature, which hide unnecessary or inactive parameters, and operation option automatically.
the 'User parameter group' feature, which quickly and easily set up certain parameters
that are frequently used, can be set up in DAQMaster. ■ Operation • H: Alarm output hysteresis
• Refer to the user manual for the details. Name Alarm operation Description
■ Parameter 1 group ■ Parameter 4 group - - No alarm output
OFF H ON OFF H ON If deviation between PV and
Parameter Display Default Parameter Display Default
SV as high-limit is higher
Control output Alarm output1 Operation Deviation SV PV PV SV than set value of deviation
RUN/STOP mode high limit 100℃ 110℃ 90℃ 100℃
temperature, the alarm
R-S RUN AL-1 DVCC
Multi SV selection SV-N SV-0 Alarm output1 Option AL!T AL-A High deviation: Set as 10℃ High deviation: Set as -10℃ output will be ON.
Heater current Alarm output1 Hysteresis A!HY
ON H OFF ON H OFF If deviation between PV
001
monitoring Alarm output1 contact
CT-A )0
and SV as low limit is higher
Alarm output1 low limit type
A!N NO Deviation
AL!L 1550 PV SV SV PV than set value of deviation
Alarm output1 high limit Alarm output1 ON delay low limit 90℃ 100℃ 100℃ 110℃
AL!H 1550 temperature, the alarm
Alarm output2 low limit time Low deviation: Set as 10℃ Low deviation: Set as -10℃ output will be ON.
A!ON 0000
AL@L 1550
Alarm output2 high limit Alarm output1 OFF delay
AL@H 1550
ON H OFF H ON If deviation between PV
Alarm output3 low limit time
A!OF 0000
AL#L 1550 Deviation and SV as high/low-limit
Alarm output3 high limit Alarm output2 Operation high, low PV SV PV is higher than set value of
mode
AL#H 1550
90℃ 100℃ 110℃
Multi SV 0
AL-2 ]]DV
limit deviation temperature, the
Alarm output2 Option
SV-0 0000
Multi SV 1 AL@T AL-A High, Low deviation: Set as 10℃ alarm output will be ON.
Alarm output2 Hysteresis A@HY
SV-1 0000
Multi SV 2 001
OFF H ON H OFF If deviation between PV and
Alarm output2 contact
SV-2 0000
Multi SV 3 Deviation SV as high/low-limit is lower
type
SV-3 0000 A@N NO
high, low than set value of deviation
■ Parameter 2 group
PV SV PV
Alarm output2 ON delay limit reverse
90℃ 100℃ 110℃
temperature, the alarm
Parameter Display Default time High, Low deviation: Set as 10℃ output will be OFF.
A@ON 0000

Auto tuning RUN/STOP Alarm output2 OFF delay

OFF H ON OFF H ON
time
AT OFF
Heating proportional Absolute If PV is higher than the
A@OF 0000

band
H-P 01)0 Alarm output3 Operation value high PV SV SV PV absolute value, the output
Cooling proportional mode limit 90℃ 100℃ 100℃ 110℃
will be ON.
AL-3 OFF

band
C-P 01)0 Alarm output3 Option AL#T AL-A Absolute value: Set as 90℃ Absolute value: Set as 110℃
Heating integral time Alarm output3 Hysteresis A#HY ON H OFF ON H OFF
Absolute If PV is lower than the
001
Alarm output3 contact
H-1 0000
Cooling integral time
type value low PV SV SV PV absolute value, the output
C-1 0000
Heating derivative time
A#N NO
90℃ 100℃ 100℃ 110℃
Alarm output3 ON delay limit will be ON.
H-D 0000
Cooling derivative time Absolute value: Set as 90℃ Absolute value: Set as 110℃
time
C-D 0000 A#ON 0000
Dead overlap band It will be ON when it detects
Alarm output3 OFF delay Sensor break -
DB 0000
Manual reset sensor disconnection.
time
REST 05)0 A#OF 0000
Heating hysteresis It will be ON when it detects
LBA time
hHYS 002
Heating OFF offset Heater break -
heater disconnection.
LBaT 0000
hOST 000
Cooling hysteresis LBA band
002
(003) It will be ON when it detects
cHYS 002 LBaB
Cooling OFF offset Loop break -
Analog Transmission loop disconnection.
cOST 000
MV low limit
output1 Mode
L-MV `0)0 AoM1 PV
MV high limit H-MV 10)0
Transmission output1 ■ Option
RAMP up change rate low limit
FsL1 -200
Condition
RAMU 000
RAMP down change rate Transmission output1 Name Description
of re-apply
RAMD 000
RAMP time unit rUNT MIN high limit
FsH1 1350
Standard If it is an alarm condition, alarm output is ON. If it is a clear alarm
■ Parameter 3 group Analog Transmission
alarm condition, alarm output is OFF.
-
output2 Mode
AoM2 PV
Parameter Display Default Transmission output2 If it is an alarm condition, alarm output is ON and maintains ON
Alarm latch -
Input specification IN-T KCaH low limit
FsL2 -200 status.
Temperature unit UNIT ><?C Transmission output2 First alarm condition is ignored and from second alarm
Analog low limit L-RG 0)00 high limit
FsH2 1350 Standby condition, standard alarm operates. When power is supplied
Analog high limit H-RG 1)00 Communication address sequence 1 and it is an alarm condition, this first alarm condition is ignored
and from the second alarm condition, standard alarm operates.
ADRS 01
Scaling decimal point Communication speed Power ON
DOT )0 BPS 96
Low limit scale L-SC 00)0 Comm. parity bit PRTY NONE Alarm If it is an alarm condition, it operates both alarm latch and
High limit scale H-SC 10)0 Comm. stop bit latch and standby sequence. When power is supplied and it is an alarm
standby condition, this first alarm condition is ignored and from the
STP 2
Display unit dUNT >?/O Response time
sequence 1 second 1alarm condition, alarm latch operates.
RSWT 20
Input correction IN-B 0000 Comm. write COMW EnA
Input digital filter First alarm condition is ignored and from second alarm
■ Parameter 5 group Power ON,
MAvF 00)1
SV low limit condition, standard alarm operates. When re-applied standby
L-SV -200 Standby change SV,
SV high limit Parameter Display Default sequence and if it is alarm condition, alarm output does
sequence 2 change
not turn ON. After clearing alarm condition, standard alarm
H-SV 1350
Multi SV number alarm
operates.
HEAT MtSV 1
(Normal
Digital input key temperature
type) Basic operation is same as alarm latch and standby sequence1.
DI-K STOP
Control output mode Digital input1 Terminal Alarm / operation
Function It operates not only by power ON/OFF, but also alarm set value, or change
latch and
O-FT H-C DI-1 OFF
(Heating&
Digital input2 Terminal or alarm option changing. When re-applied standby sequence STOP to RUN
Cooling standby
Function and if it is alarm condition, alarm output does not turn ON. mode
type) sequence 2
DI-2 OFF
After clearing alarm condition, alarm latch operates.
PID Manual control, initial MV ItMV AUTO
(Normal Manual control, preset
type)
MV
PrMV 00)0
Control type
Sensor error MV
C-MD pP
(Heating&
ErMV 00)0
Cooling- Control stop MV StMV 00)0
type) Control stop alarm
Auto tuning mode output
StAL CONT
AtT TUN1
OUT1 control output User level USER STND
selection SV setting lock
OUT1 CURR
LcSV OFF
OUT1 SSR drive output Parameter 1 group lock LcP1 OFF
type Parameter 2 group lock
O!SR STND
LcP2 OFF
OUT1 current output Parameter 3 group lock
range
LcP3 OFF
Parameter 4 group lock
O!MA 4-20
OUT2 control output
LcP4 OFF
Parameter 5 group lock
selection
LcPS OFF
Password setting
OUT2 CURR
OUT2 current output
PWD 0000

range
O@MA 4-20

Heating control cycle 02)0

(Relay)
H-T

Cooling control cycle

00@0
(SSR)
C-T
-|Transparent Guide|- -

Sold Separately: Current Transformer (CT) Sold Separately: 11-pin Controller Socket
• Unit: mm • For detailed information, refer to the ‘PG Series, PS Series’ manual.
• The current for above CTs is 50A same but inner hole sizes are different. Please use this
for your environment. Rated Rated
Appearance Pins Feature Model
• Do not supply primary current in case that CT output is open. High voltage will be Voltage current
generated in CT output.
CSTC-E80LN 7A
11-pin 250 VACᜠ (resistance Controller socket PG-11
Ø23.3 F=50Hz
Ø7
10 load)
3 Ta=25℃
100Ω
K(Black)

OUTPUT IN VOLTS RMS(V)

1 10Ω
7

L(White)
7A
3.8 Controller socket
0.1 11-pin 250 VACᜠ (resistance PS-11(N)
26.5 150 (DIN Rail / Panel)
load)
10.5

0.01
• Max. load current: 80A (50/60Hz)
• Current ratio: 1/1000
• Wire wounded resistance: 31Ω±10%
0.001
0.1 1 10 100 1000
Sold Separately: Terminal Protection Cover
SENSED CURRENT IN AMPS RMS(Io)
• Unit: mm
CSTC-E200LN
RSA-COVER: DIN W48 × H48 RMA-COVER: DIN W72 × H72
Ø37.1 F=50Hz 22
10 4 70 10
Ø13 3 Ta=25℃ 100Ω
3 □48.4 13
10Ω UP
K(Black)
OUTPUT IN VOLTS RMS(V)

1 UP
10

L(White)

68.5
41
45

64
4.5

0.1 DOWN
40.8 150 DOWN

0.01

18
13.5

22

13
• Max. load current: 200A (50/60Hz) 0.001 RHA-COVER: DIN W48 × H96 RLA-COVER: DIN W96 × H96
• Current ratio: 1/1000 0.1 1 10 100 1000
3.8 47.2 9 3.8 94 10
• Wire wounded resistance: 20Ω±10% SENSED CURRENT IN AMPS RMS(Io)

CSTS-E80PP UP UP

21.4 F=50Hz
15.4 2.9 10 Ta=25℃ 100Ω
0.5

91.5
91.5
DOWN

86
86
UP

10Ω
Ø6
OUTPUT IN VOLTS RMS(V)

1
25.47

DOWN DOWN

0.1
2.7
10.5

40.2

13
13

31 0.01
Ø3.4

0.001
Segment Table
10

0.1 1 10 100 1000

• Max. load current: 80A (50/60Hz) SENSED CURRENT IN AMPS RMS(Io) The segments displayed on the product indicate the following meanings. It may
• Current ratio: 1/1000
• Wire wounded resistance 31Ω±10% differ depending on the product.
7 segment 11 segment 12 segment 16 segment
0 0 I I 0 0 I I 0 0 I I 0 0 I I
1 1 J J 1 1 J J 1 1 J J 1 1 J J
2 2 K K 2 2 K K 2 2 K K 2 2 K K
3 3 L L 3 3 L L 3 3 L L 3 3 L L
4 4 M M 4 4 M M 4 4 M M 4 4 M M
5 5 N N 5 5 N N 5 5 N N 5 5 N N
6 6 O O 6 6 O O 6 6 O O 6 6 O O
7 7 P P 7 7 P P 7 7 P P 7 7 P P
8 8 Q Q 8 8 Q Q 8 8 Q Q 8 8 Q Q
9 9 R R 9 9 R R 9 9 R R 9 9 R R
A A S S A A S S A A S S A A S S
B B T T B B T T B B T T B B T T
C C U U C C U U C C U U C C U U
D D V V D D V V D D V V D D V V
E E W W E E W W E E W W E E W W
F F X X F F X X F F X X F F X X
G G Y Y G G Y Y G G Y Y G G Y Y
H H Z Z H H Z Z H H Z Z H H Z Z

18, Bansong-ro 513Beon-gil, Haeundae-gu, Busan, Republic of Korea, 48002

www.autonics.com | +82-2-2048-1577 | [email protected]