™

DEEPCLEAN ESSENTIAL
USER GUIDE

8852 SERIES
 IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING YOUR PORTABLE DEEP CLEANER.
When using an electrical appliance, basic precautions should be observed, including the following:

WARNING » Do not pull or carry by cord, use

cord as a handle, close a door on
cord, or pull cord around sharp
» Do not use appliance in an
enclosed space filled with vapors
given off by oil base paint, paint
TO REDUCE THE RISK OF FIRE, edges or corners. Do not run thinner, some moth proofing
ELECTRIC SHOCK, OR INJURY: appliance over cord. Keep cord substances, flammable dust,
» Connect to a properly grounded away from heated surfaces. or other explosive or toxic vapors.
outlet only. See grounding » Do not unplug by pulling on » Do not use to pick up toxic
instructions. Do not modify the cord. To unplug, grasp the plug, material (chlorine bleach,
3-prong grounded plug. not the cord. ammonia, drain cleaner, etc.).
» Do not leave appliance when it is » Do not handle plug or appliance » Do not pick up anything that
plugged in. Unplug from outlet when with wet hands. is burning or smoking, such as
not in use and before servicing. cigarettes, matches, or hot ashes.
» Do not put any object into open-
» Use indoors only. ings. Do not use with any opening » Use only BISSELL cleaning
» Do not allow to be used as a toy. blocked; keep openings free of products intended for use
Close attention is necessary when dust, lint, hair, and anything that with this appliance to prevent
used by or near children. may reduce air flow. internal component damage.
» Do not use for any purpose other » Keep hair, loose clothing, fingers, See the Cleaning Fluid section
than described in this User’s and all parts of body away from of this guide.
Guide. Use only manufacturer’s openings and moving parts. » Unplug before connecting
recommended attachments. » Turn off all controls before plug- TurboBrush Tool.
» Do not use with damaged cord ging or unplugging appliance. » Do not immerse. Use only on
or plug. If appliance is not » Use extra care when cleaning surfaces moistened by the
working as it should, has been on stairs. cleaning process.
dropped, damaged, left outdoors, » Keep appliance on a level surface.
or dropped into water, have it » Do not use to pick up flammable
repaired at an authorized or combustible materials (lighter » Do not carry the appliance while
service center. fluid, gasoline, kerosine, etc.) in use.
or use in areas where they may » Do not use without lint screen
» Always install float before any wet be present.
pick-up operation. in place.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE
This model is for household use only. Commercial use of this unit voids the manufacturer’s warranty.

WARNING GROUNDING INSTRUCTIONS

Improper connection of the equipment-grounding conductor can
This appliance must be connected to a grounded wiring system. If it
result in a risk of electrical shock. Check with a qualified electrician
should malfunction or break down, grounding provides a safe path
or service person if you aren’t sure if the outlet is properly grounded.
of least resistance for electrical current, reducing the risk of electrical
DO NOT MODIFY THE PLUG. If it will not fit the outlet, have a proper
shock. The cord for this
outlet installed by a qualified electrician. This appliance is designed Grounded
appliance has an equipment-grounding
for use on a nominal 120-volt circuit, and has a grounding attachment Outlets
conductor and a grounding plug. It must
plug that looks like the plug in the illustration. Make certain that the
only be plugged into an outlet that is
appliance is connected to an outlet having the same configuration as
properly installed and grounded in
the plug. No plug adapter should be used with this appliance.
accordance with all local codes and ordinances. Grounding Pin

www.BISSELL.com 800.237.7691
2
Thanks for buying a BISSELL deep cleaner
We’re glad you purchased a BISSELL Safety Instructions . . . . . . . . . . 2
deep cleaner. Everything we know
about floor care went into the design Product View . . . . . . . . . . . . . . . 4
and construction of this complete,
high-tech home cleaning system. Assembly . . . . . . . . . . . . . . . . . . . 5

Your BISSELL deep cleaner is well Operations . . . . . . . . . . . . . . . 6-10

made, and we back it with a limited
two-year warranty. We also stand Maintenance & Care . . . . . . . 11-12
behind it with a knowledgeable,
dedicated Consumer Care Troubleshooting . . . . . . . . . . . . 13
department, so, should you ever
have a problem, you’ll receive fast, Replacement Parts . . . . . . . . . . 14
considerate assistance.
Accessories . . . . . . . . . . . . . . . . . 14
My great-grandfather invented
the floor sweeper in 1876. Today, Warranty . . . . . . . . . . . . . . . . . . . 15
BISSELL is a global leader in the
design, manufacture, and service
Consumer Care . . . . . . . . . . . . . 15
of high quality homecare products
Product Registration . . . . . . . . 16
like your BISSELL deep cleaner.

Thanks again, from all of us

at BISSELL.

Mark J. Bissell
Chairman & CEO

Tips
» Deep cleaning stairs and high-traffic areas on a regular » B efore turning off the machine, suction up clean
basis helps prolong carpet life. water to thoroughly rinse out the interior of the flex
» Check upholstery stuffing before cleaning. Colored hose. Then, lift the cleaning tool and point it upwards
stuffing may bleed through the fabric when it to drain any remaining water into the dirty water/
becomes wet. collection tank.

www.BISSELL.com 800.237.7691
3
Product View
1
2
4

3
1 Ergonomically Designed Handle 5
2 Spray Trigger
3 Cord Clip
4 Tough Stain Tool 6
5 Ready-to-use Hose
6 Extra Long Power Cord
7 Integrated Carry Handle
8 Tank Carry Handle
9 Ready Tools™ Dial
10 Removable Nozzle
11 SurroundSuction®
12 Dirtlifter® PowerBrush
13 Edge Sweep® Brushes
14 Belt Access Door (underside of machine)
15 Handle Release
16 Power Switch 7 8
17 Large, Easy-To-Maneuver Wheels
18 4” Upholstery Tool
19 6” Stair Tool 9
20 TurboBrush® Tool 15 16
21 Hard Floor Attachment
22 Spraying Crevice Tool 10
23 2-in-1 Crevice Tool 17
24 Mesh Tool Bag (bag only)
25 Deep Reach Tool 14
26 Pet Stain Tool
11 12
27 Stain Trapper Tool
13

4 18 19 20 21

22 23 24 25 26 27

www.BISSELL.com 800.237.7691
4
Assembly WARNING
Do not plug in your deep cleaner until
you are familiar with all instructions and
The only tool you will need to assemble your
cleaner is a Phillips head screwdriver. operating procedures.
1. Slide handle assembly onto lower body and
secure with two long screws. 1. 2.
2. Attach upper hose rack to back of handle
assembly by guiding the hook up into slot
location and pressing firmly upward until it
is seated flush with the back of the machine.
Secure 1 short screw through the hole in the
bottom of the upper hose and cord rack. 4.
3. Attach lower hose rack by guiding the hook 3.
up into slot location and pressing firmly upward
until it is seated flush with the back of the
machine. Secure 2 short screws through holes
on either side of the bottom hose and cord rack.
4. Attach Tough Stain tool to end of hose.
5.
5. Wrap flex hose around hose and cord rack
and secure it into notch on holder and wrap cord
around opposite side of hose and cord rack.
6. Place tank in the bottom of the machine.

Cleaning fluid:
Keep plenty of genuine BISSELL 2X formula on
hand so you can clean and protect whenever it
fits your schedule. Always use genuine BISSELL WARNING
deep cleaning formulas. Non-BISSELL To reduce the risk of fire and electric shock
cleaning solutions may harm the machine and due to internal component damage, use
will void the warranty. only BISSELL cleaning fluids intended for use
with the deep cleaner.

Professional Deep Clean

Pet Stain & Odor Allergen Cleansing Spring Breeze Crystal Springs Hard Floor Solutions Stain Pretreat
Deep Cleaning & Protect
78H6-3 99K5-2 62E5-2 89Q5-2 26V2-A 7191-3 56L9 4001
Removes tough pet Deep cleans carpets For use with Pretreat to
Out Cleans Powerful Powerful
stains and contains and protects from Helps remove pet & the Bare penetrate
Best for all other cleaning with a cleaning with
patented odor future stains with pollen allergens Floor Tool and loosen
formulas refreshing scent a refreshing scent
removal technology Scotchgard™ Protector (select models) tough stains
2X Concentrated X X X X X X X
Scotchgard™ Protection® X X X

Tip
*ONLY BISSELL Protects
from future stains with » Deep cleaning carpeting
Scotchgard™ Protector regularly can reduce dust and
allergens in your home.
Scotchgard™ is a trademark of 3M®.

www.BISSELL.com 800.237.7691
5
 Operations
Before you clean
1. Plan activities to give your carpet time to dry.
2. Move furniture to another area if cleaning an
entire room (optional).
3. Vacuum area with a dry vacuum cleaner 9
8
7

before deep cleaning. 5

6

4. Plan your cleaning route to leave an exit path.

4

1
It is best to begin cleaning in the corner farthest 3
2

from your exit.

5. Pretreating (optional)
Pretreating is recommended to improve cleaning

WARNING
effectiveness for heavily soiled carpet in high
traffic areas such as entry ways and hallways.
To pretreat: To reduce the risk of fire and electric shock due to internal
a. Using the BISSELL Stain Pretreat, component damage, use only BISSELL cleaning fluids
generously spray evenly over soiled intended for use with the deep cleaner.
area, do not overwet.
b. Wait 3-5 minutes before deep cleaning.

ATTENTION
c. Clean as normal using your BISSELL
deep cleaner.
Some Berber carpets have a tendency to fuzz with wear.
Repeated strokes in the same area with an ordinary
vacuum or deep cleaner may aggravate this condition.
Please see Stain Removal instructions on page 11.

www.BISSELL.com 800.237.7691
6
Operations
Machine prep
1. Remove the tank from the base of the
machine by lifting the tank carry handle.
2. Carry like a bucket to the sink. Pull upward 1. 2.
on bottom edge of the latch in the back of the
tank to unhook and remove the lid.
3. Pull up on the bladder fill cover that says
“Fill Here”. Fill the bladder with clean hot
tap water. *Do not boil or microwave water
as it can destroy the bladder.
4. Using the provided measuring cup, fill to 3. 5.
the indicated fill line on the measuring cup
and pour in to the bladder.
5. Replace the tank lid by seating the front
edge of the tank before the back, then lock
the latch in place.
NOTE: Remember to secure the lid and test
to make sure it is secure before picking up 6.
the tank.
6. Place tank into machine base, seating
firmly in place.

Carpet cleaning
1. Plug the deep cleaner into a proper outlet. Set
ReadyTools dial to the Floor Cleaning setting.
Turn the power on by pressing the red power
switch on the back of the unit with your foot.
2. With your foot, press the gray handle release
lever located on the back of unit below water
tank to detent handle.
3. While pressing the spray trigger, make one
slow forward wet pass and another back. Let the
BISSELL advanced deep cleaning formula, and Power Switch Handle Release
DirtLifter PowerBrush do the work for you.
Caution: Do not overwet.
4. Release the spray trigger and make one
slow forward and backward pass over the
same area to remove any residual dirty water WARNING
and aid in drying. To reduce the risk of fire and electric shock due to internal
5. Repeat cleaning passes until solution being component damage, use only BISSELL cleaning fluids
suctioned up appears clean. Continue passes intended for use with the deep cleaner. Non-BISSELL
without pressing the trigger until you can’t see cleaning solutions may harm the machine and void
any more water being suctioned up. the warranty.

Tip » Thorough vacuuming before

deep cleaning wll prevent
early clogging of the lint trap.

www.BISSELL.com 800.237.7691
7
 Operations
Empty the 2-in-1 water tank/clean removable nozzle
1. Turn power switch off. Remove the 2-in-1 water
tank from the base using the tank carry handle. 1. 2.
Carry the tank like a bucket to a utility sink
where you will dispose of the collection water.
Pull upward on bottom edge of the latch in the
back of the tank to unhook and remove the lid.
2. Empty collection water from bottom of tank.
3. After each use, remove any debris trapped in
the red lint screen on the base of the machine Lint Screen
while the tank is still out of the machine. 3. 4.
4. If nozzle needs to be cleaned: remove by
grasping handle at the top and pulling forward.
Clean removable nozzle by rinsing under
running water.
5. When finished, replace nozzle by slightly
raising front of machine to line up slots on the
base with the hooks on nozzle. Attach at base
first and then click nozzle into place.
NOTE: If nozzle is not attached properly loss 5.
of suction will occur.
6. To continue carpet cleaning, refer back to
step 3 on page 7.
If cleaning is complete, refer to the “Maintenance
and Care” section on page 12.

Ready Tools™
Your DeepClean Essential deep cleaner comes
equipped with a hose and at least one attach-
ment for cleaning stairs, upholstery, and more.
Important! If using the machine to clean
upholstery, check upholstery tags.
1. Check manufacturer’s tag before cleaning.
“W” or “WS” on the tag means you can use your
DeepClean Essential. If the tag is coded with “X”
or “S” (with a diagonal strike through), or says
“Dry Clean Only,” do not proceed. Do not use on
velvet or silk. If manufacturer’s tag is missing or
not coded, check with your furniture dealer.
2. Check for colorfastness in an inconspicuous
place.
3. If possible, check upholstery stuffing. Colored
stuffing may bleed through fabric when wet.
4. Plan activities to give upholstery time to dry.
Ad bj jh
sd jkn f h
cv hh
b j

fd hn l kl
gcg

d b lg
gh j j h
g kvh
bvh

5. Vacuum thoroughly to pick up loose debris

and pet hair. Use a vacuum with a brush
attachment and a crevice tool to clean in fabric
folds and tufts.
6. To begin cleaning with attachments, follow
the instructions on page 7 for filling the Manufacturer’s tag
2-in-1 water tank.

www.BISSELL.com 800.237.7691
8
Operation
7. Set the ReadyTools dial to the TOOLS
setting. This will allow spray and suction from
the hose. 7.
8. Attach the cleaning tool of your choice to the
end of the hose.
9. Clean by pressing the trigger to spray solu-
tion onto the area to be cleaned. Slowly move
the tool back and forth over the soiled surface.
Release the trigger to suction dirty water.
Continue to clean in the area, working
in small sections, until dirt is removed.
Caution: Do Not Overwet.
10. When finished cleaning, remove and rinse
tool(s) in clean, running water.
11. It is recommended that you suction clean
water from the tap to rinse out the hose. Be
careful not to over-fill your tank. 11. 12.
12. Before wrapping hose onto tool rack, lift
end of hose and stretch out to ensure all water
is cleared from hose.
13. Wrap flex hose around hose and cord rack.
14. Empty 2-in-1 water tank and rinse out,
following instructions on page 12.
15. If the ReadyTools dial becomes difficult to
turn, the diverter assembly that holds the dial
may need to be cleaned. To clean, first remove
nozzle and locate screw that holds the diverter 15. 16.
assembly in place. With a Phillips screwdriver,
remove the screw and set aside.
16. Remove diverter assembly; hold under
running water making sure water flows through
and around the dial. Turn the dial about 10
times clockwise and 10 more times counter
clockwise. This should free up any debris.
17. Wipe diverter assembly with a soft cloth
and replace back on machine. Replace nozzle.
18. Return ReadyTools dial to FLOOR
CLEANING setting.

www.BISSELL.com 800.237.7691
9
 Operations
Hard Floor Cleaning
Your deep cleaner may have included a hard
floor tool and 2X Hard Floor Solutions Formula.
If not, these products are available for purchase
by contacting the BISSELL Consumer Care
WARNING
To reduce the risk of fire and electric shock when
department by phone or at the website. The cleaning a hard floor, the BISSELL hard floor tool
hard floor tool provides effective cleaning for 160-1523 must be used and it must only be used
linoleum, vinyl, and tile floors.
Caution: Do not use on unsealed hardwood with BISSELL 2X Hard Floor Solutions cleaning fluid
floors. intended for use with this appliance.
1. Thoroughly vacuum or sweep floor to pick up
any debris.
NOTE: Prior to filling with formula and water be
sure all carpet cleaning formula is thoroughly
rinsed from tank.
2. Fill the bladder with clean hot tap water and
set aside.
3. Fill BISSELL 2X Hard Floor Solutions Formula
to the indicated fill line in the provided measur-
ing cup and pour into mouth of bladder. Set tank
aside until after hard floor tool is installed.
4.
4. Fully detent handle and let it rest on the floor.
Lift machine base so that underside is easily
accessible, then attach the hard floor tool to
the bottom of the machine by hooking it into
the nozzle and swinging it down until it clicks
into place.
5. Place tank in to machine base, seating firmly
in base. Be sure the ReadyTools dial is set to
FLOOR CLEANING.
6. Plug into an outlet and turn the power on.
7. Plan your cleaning route to leave an exit path.
Be sure to allow adequate time for floors to dry.
8. While pressing the spray trigger, make one
slow forward wet pass and another back.
Caution: Do Not Overwet.
9. Repeat the motion without pressing the
trigger using the hard floor tool to squeegee and
suction up the dirty water.
10. When finished, remove hard floor tool,
rinse and let dry before storing. Refer to the
Maintenance section on page 12 for machine
clean up and storage instructions.

www.BISSELL.com 800.237.7691
10
Maintenance & Care
Machine care
For best results, a few simple steps can assure
your machine is well maintained after cleaning
is complete. WARNING
1. Turn power switch off. Unplug the machine To reduce the risk of electric shock, turn power switch
and wrap the power cord. off and disconnect plug from electrical outlet before
performing maintenance or troubleshooting checks.
2. After emptying the 2-in-1 water tank, rinse it
with running hot tap water, taking care to clean

Tip
underneath and around the heavy duty bladder.
Clean out red lint screen prior to replacing tank.
Removable nozzle may be rinsed if necessary.
3. Replace the 2-in-1 water tank on the machine.
4. Any loose hair or debris can be pulled from » Let all parts
the brush roll and thrown away. See page 12 for dry completely
instructions on removing the brush roll. before storing
5. Clean the ReadyTools dial assembly area by
following instructions in Step 15 on page 9.
6. To clean attachments, remove from hose and
rinse in clean, running water. Dry before stor-
ing. Clean the hose by suctioning clean water
from the tap (taking care not to let the tank
overflow). Before wrapping back on machine, lift
end of hose and stretch out to ensure all water is
cleared from hose. Refer to page 9, illustrations
11 and 12.
7. Wipe the machine’s exterior with a soft cloth.
8. After carpet is dry, you may wish to vacuum
again to remove any leftover hair and fuzz the
deep cleaner may have brought to the carpet
surface.

Machine storage
Put the unit away in a closet or basement for
the next use. Store cleaner in a protected, dry
area. Since this product uses water, it must not
be stored where there is a danger of freezing.
Freezing will damage internal components and
void the warranty.

www.BISSELL.com 800.237.7691
11
 Maintenance & Care
Belt Replacement Instructions
1. Turn off the machine and unplug it from the
outlet. Wrap hose and cord on wraps.
2. Remove the 2-in-1 water tank and set aside.
WARNING
To reduce the risk of electric shock, turn power switch
3. IMPORTANT: Fully recline handle and turn
unit upside down.
off and disconnect plug from electrical outlet before
performing maintenance or troubleshooting checks.
4. Locate red Belt Access Door and remove two
screws.
NOTE: The dark screw is a long machine screw
and will take several turns (approximately 25) 4.
to completely remove. The head of the screw
will lift from the belt access door so that it can
be easily removed.
5. Pull the belt access door away from the brush
and remove the belt access door and end cap
and set aside.
6. Remove brush belt from end of brush and 5.
set aside. Check for wear or damage. Replace if
necessary.
7. Check motor belt for damage. If necessary,
replace the motor belt by pinching the belt at
one end to make a large loop then attaching
the motor belt to the silver motor shaft first and
attaching to the larger red pulley.
NOTE: Spinning the red pulley a few 6.
times will help center the belt and ensure
correct assembly.
8. If necessary, the brush may be removed for
cleaning. Rotate the brush out of the brush hous-
ing and pull the brush off the axle attached to
the remaining end cap. The remaining pivot arm
can be removed by removing the screw (this will
allow for full access to the brush chamber for
cleaning and proper maintenance). Make sure
the “keyed” end of the metal rod is aligned with
the slot in the pivot arm before reassembly. Rinse
the brush under running water and remove any
hair, carpet fibers, or other debris that may have
become wrapped around the brush or stuck in
the bristles. Allow the brush to dry and replace
it on the axle, cogged-side last. You may need
to rotate the brush to allow it to slide all the way
down the axle.
9. Reattach brush belt.
10. Reattach Belt Access Door assembly to end
of brush and rotate back into place. Replace
screws.
NOTE: Do not over tighten screws.
If you have any questions or are having trouble
installing or replacing your belt(s) or brush,
please call BISSELL Consumer Care.

www.BISSELL.com 800.237.7691
12
Troubleshooting WARNING
To reduce the risk of electric shock, turn power switch
off and disconnect plug from electrical outlet before
performing maintenance or troubleshooting checks.

Problem Possible causes Remedies

Bladder may be empty. Turn power switch off; Refill bladder
with clean hot tap water and formula.
2-in-1 tank may not be seated Turn power switch off; remove tank
Reduced properly. and reseat tank.
spray OR
no spray Pump may have lost prime. Turn power switch off; after 1 minute turn
on and depress spray release trigger.
The motor belt may be broken. Follow belt replacement instructions
on page 12.

DirtLifter The brush belt or motor belt is Follow belt replacement instructions
PowerBrush off or broken. on page 12.
does not turn

ReadyTools dial may be on the Set ReadyTools dial to either floor

wrong setting for the cleaning job. cleaning or tools.
Poor tool position. (Hand held Adjust angle; apply more downward
attachments only). pressure.
Removable nozzle may not be Make sure nozzle is on correctly by
properly attached. slightly raising front of machine to line
up slots on the base of the machine
Cleaner with the hooks on nozzle. Attach at
not picking base first and then click nozzle into
up solution place. Refer to image 5 on page 8.
2-in-1 tank lid is not properly installed. Re-install lid; refer to images on page 7.
2-in-1 tank is not properly seated. 2-in-1 tank must be firmly seated to
function; remove and reseat 2-in-1 tank.
2-in-1 tank has picked up maxi- Empty 2-in-1 tank and refill, refer to
mum dirty water. the Operation section.
The lint screen may be clogged. Clean out lint screen. Refer to page 8.

Other maintenance or service not included in the manual should

Please do be performed by an authorized service representative.
not return Thank you for selecting a BISSELL product.
this product For any questions or concerns, BISSELL is happy to
to the store. be of service. Contact us directly at 1-800-237-7691.

www.BISSELL.com 800.237.7691
13
 Replacement Parts
These items are available for your BISSELL DeepClean Essential deep cleaner.
Call 1-800-237-7691 or visit www.BISSELL.com
PART # PART NAME PART # PART NAME
160-1525 Tank Assembly Complete 160-1529 Tank Base

160-1535 Removable Nozzle 160-1543 Replacement Pump Belt (with

instructions)

160-1542 Replacement Brush Belt (with 160-1526 Tank Top (with Handle)
instructions)

160-1519 Upper Hose and Cord Rack 160-1520 Lower Hose and Cord Rack

160-1537 Brush Roll Assembly

with Pivot Arms

*Not all parts are included with every model.

Accessories
These items are available for your BISSELL DeepClean Essential deep cleaner.
Call 1-800-237-7691 or visit www.BISSELL.com

PART # PART NAME PART # PART NAME

160-1523 Hard Floor Tool 203-6651 3" Tough Stain Tool

203-6653 4" Upholstery Tool 203-6654 6" Stair Tool

203-6652 Powered TurboBrush® Tool 203-0116 Spraying, 2-in-1 Crevice Tool

w/ Brush

203-6655 Spraying Crevice Tool 210-3040 Mesh Tool Storage Bag

160-1522 Pet Stain Tool 160-0057 Deep Reach Tool

160-0057 Stain Trapper Tool

Cleaning Formula: Refer to bottom of page 5 of this guide for a full selection of cleaning
formula available for purchase.
*Not all parts are included with every model.
www.BISSELL.com 800.237.7691
14
Warranty Service
This warranty gives you specific legal rights, and you may also If your BISSELL product should
have other rights which may vary from state to state. If you need require service:
additional instruction regarding this warranty or have questions Contact BISSELL Consumer Care to locate a BISSELL Authorized Service
regarding what it may cover, please contact BISSELL Consumer Center in your area.
Care by E-mail, telephone, or regular mail as described below.
If you need information about repairs or replacement parts, or if you
Limited Two-Year Warranty have questions about your warranty, contact BISSELL Consumer Care.
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon
receipt of the product BISSELL will repair or replace (with new or Website or E-mail:
remanufactured components or products), at BISSELL’s option, free www.BISSELL.com
of charge from the date of purchase by the original purchaser, for Or Call:
two years any defective or malfunctioning part. BISSELL Consumer Care
See information below on "If your BISSELL product should 1-800-237-7691
require service". Monday – Friday 8am - 10pm ET
Saturday 9am - 8pm ET
This warranty applies to product used for personal, and not commercial Sunday 10am - 7pm ET
or rental service. This warranty does not apply to fans or routine
maintenance components such as filters, belts, or brushes. Damage or Or Write:
malfunction caused by negligence, abuse, neglect, unauthorized repair, BISSELL Homecare, Inc.
or any other use not in accordance with the User's Guide is not covered. PO Box 3606
Grand Rapids, MI 49501
BISSELL IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ATTN: Consumer Care
OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S
LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT.
Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the
above limitation or exclusion may not apply to you.
*EXCEPTIONS AND EXCLUSIONS FROM
THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER
WARRANTIES EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES
WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE LIMITED TO THE TWO YEAR DURATION FROM THE
DATE OF PURCHASE AS DESCRIBED ABOVE.
Some states do not allow limitations on how long an implied
warranty last so the above limitation may not apply to you.
NOTE: Please keep your original sales
receipt. It provides proof of date of purchase
in the event of a warranty claim.

www.BISSELL.com 800.237.7691
15
 Register your product today!
Registering is quick, easy and offers you benefits over the lifetime of your product.
You’ll receive:

BISSELL Rewards Points Product Support Reminders

Automatically earn points for and Alerts
discounts and free shipping on We’ll contact you with any
future purchases. important product maintenance
reminders and alerts.
Faster Service
Supplying your information now Special Promotions
saves you time should you need to Optional: Register your email
contact us with questions regarding to receive notice of offers,
your product. contests, cleaning tips and more!

Visit www.BISSELL.com/registration now!

BISSELL Consumer Care

For information about repairs or replacement parts, or questions about your warranty:

Call: Write:
BISSELL Consumer Care BISSELL Homecare, Inc.
1-800-237-7691 PO Box 3606
Monday - Friday 8 am - 10 pm ET Grand Rapids MI 49501
Saturday 9 am - 8 pm ET ATTN: Consumer Care
Sunday 10am - 7pm ET

Visit the BISSELL website: www.BISSELL.com

When contacting BISSELL, have model number of cleaner available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It provides proof of purchase
date in the event of a warranty claim. See Warranty on page 15 for details.

We can’t wait to hear from you!

Rate this product and let us (and millions
of your closest friends) know what you think!

www.BISSELL.com
©2013 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in China
Part Number 160-1419 Rev 04/13
Visit our website at: www.BISSELL.com
Scotchgard is a trademark of 3M
16