TCP
Modbus Converter
TCP Modbus Converter
Modbus RTU to Modbus TCP
Modbus TCP to Modbus RTU
Modbus RTU to Modbus TCP
WE-62C
USER MANUAL
Version 1.0
USER MANUAL
Wiman Communication Technologies
No.1, First Floor,
Narasingapuram Main Road, Maduvankarai
Guindy, Chennai - 6000032.
Ph : +91-44 48536045
[email protected]|www.wiman.in12, Jafferbhoy Industrial Estate, Makwana
Rd, Marol Naka, Andheri East, Mumbai,
Maharashtra 400059 | (022) 48964488
TCP Modbus Converter WE-62C
Table of Contents
1 Introduction .......................................................................................................................4
2
2 Hardware Description .......................................................................................................5 3
2.1 Specifications .............................................................................................................5 3
2.2 LED Status ................................................................................................................5 3
3 Getting Started ..................................................................................................................6
4
3.1 Info & Device Setting ................................................................................................8 6
3.3 TCP Slave – Modbus Master (Modbus RTU to Modbus TCP) ...............................11 7
3.4 Configuration File Operations .................................................................................13 9
3.5 Device Packet Status Info ........................................................................................13 9
3.6 Console – Read/Write Commands ...........................................................................13 9
Page : 3
TCP Modbus Converter USER MANUAL
WE-62C // ST-56
1 Introduction
In Industrial Internet of Things (IIoT), protocol conversion has been the key to
connecting legacy and different vendor devices to networks. The most common protocol
conversion is Modbus-RTU-to-Modbus-TCP conversion, and is usually required when metering
devices, mostly using Modbus RTU, need to be integrated with SCADA systems, mostly using
Modbus TCP. Generally, two ways of Conversion will be required
Modbus RTU to Modbus TCP
Modbus TCP to Modbus RTU
PIN Details
Pin No. Pin Name Description
1 +12V DC IN - Input voltage: 12V~24V/1A.
2 GND Ground
3 RXD / D+ / A RS232 Txd / RS485 Data+
4 TXD / D- / B RS232 Rxd / RS485 Data-
5 NC NC
6 NC NC
7 NC NC
8 NC NC
RJ45 LAN 10/100 Mbps
Page : 4
www.faclon.com 2
TCP Modbus Converter USER MANUAL
WE-62C // ST-56
2 Hardware Description
2.1 Specifications
System
CPU ARM Cortex
SRAM 32 Kbytes
Flash Memory 256 Kbytes
WDT(watchdog) Yes
LAN Port
RJ45 Port 10/100 Mbps Auto Negotiable
Serial ports
RS232 Utility port RS-232: TxD, RxD, GND (use for device configuration and debug)
RS485 RS-485: D+, D- (use for communication with other devices)
Baud Rate Supports 2400,4800,9600,19200,38400,57600,115200
Power
Operating Voltage 12VDC to 24VDC
Mechanical
Casing Plastic
Dimensions (W x L x H) 90mm x 100mm x 25mm
Environmental
Operating Temperature -25 Ԩ +55Ԩ
Ambient Relative Humidity 5 ~ 95% RH, non-condensing
2.2 LED Status
LED NAME DESCRIPTION
GREEN POWER Light when Power on the device
LED Status Connection State
Flashing (ON for 100ms and OFF for LAN Network Not Connected
100ms)
RED GSM Flashing (ON for 500ms and OFF for LAN Connected to Device
500ms)
Double Blink Once at every 3sec IP is Connected to Server/Client
GREEN COM TX Blink on data Transmission in RS485/RS232 port
YELLOW COM RX Blink on data Reception in RS485/RS232 port
Page : 5
www.faclon.com 3
TCP Modbus Converter USER MANUAL
WE-62C // ST-56
3 Getting Started
Basic Requirement for Testing
Hardware
1. TCP Modbus Converter ST-56 (With Power Setup)
2. USB to RS-485 Converter
3. LAN Cable
Software
1. Modbus Simulator (Act as Slaves): Modbus Slave or Mod Sim or ModRSsim
2. Modbus Scanner (Act as Polling): Modbus Poll or Mod Scan
Step 1: Set IP in Laptop / Desktop to Access Device Configuration
Device Factory default IP: 192.168.1.100 : 255.255.255.0 : 192.168.1.1
Run -> ncpa.cpl
- Open Ethernet Adaptor (Double Click) and
Set the IP Address
Page : 6
www.faclon.com 4
TCP Modbus Converter USER MANUAL
WE-62C // ST-56
Step 2: Connect LAN Cable to the device and PC
Power Up the Device, wait for 20 Sec
Check CON LED (RED) Status – ON and OFF every 500ms, Else wait for this Status
Step 3: Check IP is Connected to the Network
Run -> Cmd -> ipconfig/all
Step 4: Using WimNet Network Scanner Tool (To find List of Devices in network)
1
3
Scanner Software will List out the devices connected in the Network or Laptop – Directly
Select the Specific IP and Click Web, It Opens the Configuration Web Portal in Web Browser
Step 5: Login with Credentials (User name: wimnet | Password: 1234 )
Page : 7
www.faclon.com 5
TCP Modbus Converter USER MANUAL
WE-62C // ST-56
3.1 Info & Device Setting
1 Device IP Network info
Device Connection and Packet Info
Device H/W, S/W Version Info
Edit for Device Setting
Edit for Device IP Settings
Edit Serial (RS485/232) Com Settings
Edit Modbus ID and Timeout Setting
Page : 8
www.faclon.com 6
TCP Modbus Converter USER MANUAL
WE-62C // ST-56
3.3 TCP Slave – Modbus Master (Modbus RTU to Modbus TCP)
www.faclon.com
Test Connection Setup
Software Used for Testing - Simulator: Modbus Slave and Scanner: Modbus Poll
www.faclon.com
Page : 11
www.faclon.com 7
TCP Modbus Converter USER MANUAL
WE-62C // ST-56
Simulator: Modbus Slave (RS485 Connection) Scanner: Modbus Poll (TCP Connection)
Modbus Slave Starts (Server) ready to give for Poll Modbus Poll Successfully Connected and Read
If Modbus Slave is Not Connected
Page : 12
www.faclon.com 8
TCP Modbus Converter USER MANUAL
WE-62C // ST-56
3.4 Configuration File Operations
Any Settings Updated, Have to Save the Configuration in Device
Update Firmware/Configuration file to the Device - File open
Take Backup/Download the Configuration file from device to PC
Restore the Factory Setting – Set by Manufacture
Reset the Device (Software RESET)
3.5 Device Packet Status Info
3.6 Console – Read/Write Commands
Page : 13
www.faclon.com 9
