ORDER NO.

CRT3563
DEH-P580MP/XN/UC

MULTI-CD CONTROL HIGH POWER CD/MP3/WMA/AAC PLAYER WITH FM/AM TUNER

DEH-P580MP
MULTI-CD CONTROL HIGH POWER CD/MP3/WMA PLAYER WITH FM/AM TUNER
/XN/UC

DEH-P5800MP/XN/UC
This service manual should be used together with the following manual(s):
Model No. Order No. Mech. Module Remarks

CX-3164 CRT3583 S10.5COMP1 CD Mech. Module : Circuit Descriptions, Mech. Descriptions, Disassembly

For details, refer to "Important Check Points for Good Servicing".

PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan

PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2005
K-ZZA.NOV. 2005 Printed in Japan
 1 2 3 4

SAFETY INFORMATION
CAUTION
A
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair
complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so
and refer the repair to a qualified service technician.

WARNING

This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of
B California to cause cancer, birth defects or other reproductive harm.
Health & Safety Code Section 25249.6 - Proposition 65

- CD Section Precaution
1. You should conform to the regulations governing
the product (safety, radio and noise, and other
regulations), and should keep the safety during
servicing by following the safety instructions
described in this manual.
C 2. Before disassembling the unit, be sure to turn off
the power. Unplugging and plugging the connectors
during power-on mode may damage the ICs inside
the unit.
3. To protect the pickup unit from electrostatic discharge
during servicing, take an appropriate treatment
(shorting-solder) by referring to "the DISASSEMBLY".
4. After replacing the pickup unit, be sure to check the
grating.

DEH-P580MP/XN/UC
2
1 2 3 4
 5 6 7 8

[Important Check Points for Good Servicing]

In this manual, procedures that must be performed during repairs are marked with the below symbol.
Please be sure to confirm and follow these procedures.
A
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by
following the safety instructions described in this manual.

1 Use specified parts for repair.

Use genuine parts. Be sure to use important parts for safety.

2 Do not perform modifications without proper instructions.

Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.

3 Make sure the soldering of repaired locations is properly performed. B

When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)

4 Make sure the screws are tightly fastened.

Please be sure that all screws are fastened, and that there are no loose screws.

5 Make sure each connectors are correctly inserted.

Please be sure that all connectors are inserted, and that there are no imperfect insertion.

6 Make sure the wiring cables are set to their original state.

Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc. C
7 Make sure screws and soldering scraps do not remain inside the product.

Please check that neither solder debris nor screws remain inside the product.

8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.

Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.

9 There should be no spark traces or similar marks on the power plug.

When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.

0 Safe environment should be secured during servicing. D

When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.

2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.

3. Lubricants, Glues, and Replacement parts

Use grease and adhesives that are equal to the specified substance.
Make sure the proper amount is applied.
E

4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.

5. Shipping mode and Shipping screws

To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be
installed before shipment. Please be sure to follow this method especially if it is specified in this manual.

DEH-P580MP/XN/UC
5 6 7 8
3
 1 2 3 4

CONTENTS
SAFETY INFORMATION ..................................................................................................................................... 2
1. SPECIFICATIONS ............................................................................................................................................ 5
A
2. EXPLODED VIEWS AND PARTS LIST ............................................................................................................ 7
2.1 PACKING ................................................................................................................................................... 7
2.2 EXTERIOR................................................................................................................................................. 8
2.3 CD MECHANISM MODULE..................................................................................................................... 10
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM .......................................................................................... 12
3.1 BLOCK DIAGRAM ................................................................................................................................... 12
3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE).............................................................................. 14
3.3 KEYBOARD UNIT.................................................................................................................................... 20
3.4 CD MECHANISM MODULE(GUIDE PAGE) ............................................................................................ 22
4. PCB CONNECTION DIAGRAM ..................................................................................................................... 32
4.1 TUNER AMP ASSY ................................................................................................................................. 32
4.2 KEYBOARD UNIT.................................................................................................................................... 36
B 4.3 CD CORE UNIT(S10.5COMP1)............................................................................................................... 38
4.4 PANEL UNIT ............................................................................................................................................ 40
5. ELECTRICAL PARTS LIST ............................................................................................................................ 41
6. ADJUSTMENT ............................................................................................................................................... 47
6.1 CD ADJUSTMENT................................................................................................................................... 47
6.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT .................................................... 49
6.3 ERROR MODE ........................................................................................................................................ 51
6.4 SYSTEM MICROCOMPUTER TEST PROGRAM ................................................................................... 52
6.5 OEL ADJUSTMENT................................................................................................................................. 52
7. GENERAL INFORMATION ............................................................................................................................. 53
7.1 DIAGNOSIS ............................................................................................................................................. 53
7.1.1 DISASSEMBLY ..................................................................................................................................... 53
C 7.1.2 CONNECTOR FUNCTION DESCRIPTION .......................................................................................... 56
7.2 IC ............................................................................................................................................................. 57
7.3 OPERATIONAL FLOW CHART ............................................................................................................... 67
8. OPERATIONS ................................................................................................................................................ 68

DEH-P580MP/XN/UC
4
1 2 3 4
 5 6 7 8

1. SPECIFICATIONS

DEH-P580MP/XN/UC
5 6 7 8
5
 1 2 3 4

DEH-P580MP/XN/UC
6
1 2 3 4
 5 6 7 8

2. EXPLODED VIEWS AND PARTS LIST

NOTES : • Parts marked by " * " are generally unavailable because they are not in our Master Spare Parts List.
• The > mark found on some component parts indicates the importance of the safety factor of the part.
A
Therefore, when replacing, be sure to use parts of identical designation.
• Screw adjacent to mark on the product are used for disassembly.
"
• For the applying amount of lubricants or glue, follow the instructions in this manual.
(In the case of no amount instructions,apply as you think it appropriate.)
2.1 PACKING

4 B

PACKING SECTION PARTS LIST

Mark No. Description Part No. Mark No. Description Part No.
1 Polyethylene Bag CEG1173 * 17 Battery CEX1065
2 Cord Assy XDE7007 18 Carton(P580MP) XHG7108
3 Accessory Assy CEA4993 Carton(P5800MP) XHG7107
4 Case Assy(P580MP) CXB3520 19 Contain Box(P580MP) XHL7108
5 Screw Assy CEA5317 Contain Box(P5800MP) XHL7107

6 Fixing Screw BPZ20P060FTB 20 Protector XHP7016

7 Screw CBA1650 21 Protector XHP7017
* 8 Polyethylene Bag CEG-127 22-1 Owner's Manual(P580MP) XRD7097 E
9 Screw CRZ50P090FTC Owner's Manual(P5800MP) XRD7095
10 Screw TRZ50P080FTC 22-2 Installation Manual(P580MP) XRD7098
Installation Manual(P5800MP) XRD7096
* 11 Polyethylene Bag CEG-158
12 Handle CNC5395 * 22-3 Caution Card XRP7005
13 Holder CND1249 22-4 Caution Card CRP1310
14 Holder CND1250 * 22-5 Warranty Card(P580MP) CRY1070
15 Bush CNV3930 * Warranty Card(P5800MP) CRY1246
* 22-6 Caution Card(P5800MP) CRP1294
16 Remote Control Assy CXC5719

Owner's Manual,Installation Manual

F
Part No. Language

XRD7095,XRD7096,XRD7097,XRD7098 English,French

DEH-P580MP/XN/UC
5 6 7 8
7
 1 2 3 4

2.2 EXTERIOR
69 82
A 73
66
75 84 74 81
A
85 88
14 86 68 80 D
89 79
19 67 65
87 71 72
70
78
76
40 77
49 67

B 40

B 67 83
39
55 40
47 46 56 51
6
50
60
58
41
62 59 5154 57
52 92
48
45
61 53 90
42
63 43 15 91
64 44 C 9
C 20
35 8
3 3 94 23
3 4 21 38 23
96 34
30 33
3 95 93
31
21
95
29 B 27 24 22
26
36
13 25
28
37
D
18 32
A
16
1

11

17

E
C
B 5
5
12
2
7
A 5

10
F 2

DEH-P580MP/XN/UC
8
1 2 3 4
 5 6 7 8
EXTERIOR SECTION PARTS LIST
Mark No. Description Part No. Mark No. Description Part No.
1 Screw ASZ26P050FTC 50 Connector(CN1901) CKS5207
2 Screw BMZ30P040FTB
A
3 Screw BSZ26P060FTC 51 Cushion CNM6633
4 Screw BSZ30P060FTC 52 Spacer CNM7697
5 Screw BSZ30P200FTC 53 Spacer CNM7698
54 Holder CNV6910
6 Case CNB2793 55 OEL Unit MXS8221
7 Holder CNC8659
8 Earth Plate CNC8915 56 Holder XNC7006
9 Cushion CNM8890 57 Cushion XNM7049
10 Chassis Unit CXB9528 58 Sub Grille Assy(P580MP) XXA7397
Sub Grille Assy(P5800MP) XXA7391
11 Remote Control Assy CXC5719 59 Lighting Conductor XNV7024
12 Cover CNS7068 B
13 CD Mechanism Module(S10.5) CXK5752 60 Holder XNV7025
14 Cord Assy XDE7007 61 Grille Unit(P580MP) XXA7386
15 Cord Assy XDE7009 Grille Unit(P5800MP) XXA7370
62 Button Unit(P580MP) XXA7389
16 Cable XDE7016 Button Unit(P5800MP) XXA7387
17 Insulator XNM7100
18 Insulator XNM7106 63 Knob Unit XXA7398
19 Panel(P580MP) XNS7159 64 Spring XBL7004
Panel(P5800MP) XNS7129 65 Button(EJECT) CAC7752
66 Screw(M2 x 4) CBA1649
20 Tuner Amp Assy(P580MP) XWM7130 67 Screw(M2 x 4.5) CBA1925
Tuner Amp Assy(P5800MP) XWM7131 C
21 Screw ASZ26P060FTC 68 Washer CBF1038
22 Screw BPZ26P080FTC 69 Spring CBH2650
23 Screw BSZ26P160FTC 70 Spring CBH2651
71 Spring CBH2652
> 24 Fuse(10 A) CEK1208 72 Spring CBH2653
25 Pin Jack(CN352) CKB1051
26 Plug(CN901) CKM1376 73 Holder CND1254
27 Plug(CN351) CKS1238 74 Gear CNV5997
28 Plug(CN801) CKS3537 75 Arm CNV7400
76 Arm CNV7401
29 Connector(CN651) CKS3834 77 Arm CNV7402
30 Connector(CN161) CKS4124 D
31 Connector(CN101) CKS5271 78 Arm CNV7403
32 Antenna Jack(CN401) CKX1056 79 Panel Unit CWM9835
33 Holder CND1270 80 Connector(CN1951) CKS4806
81 Connector(CN1950) CKS5192
34 Holder CND1352 82 Holder Unit CXB9501
35 Heat Sink CNR1668
36 FM/AM Tuner Unit CWE1952 83 Holder Unit CXB9502
37 Holder CND1054 84 Damper Unit CXB9503
38 Insulator XNM7031 85 Sub Panel Unit XXA7361
86 Cover CNM6854
39 Detachable Assy(P580MP) XXA7396 87 Lighting Conductor CNV6487
E
Detachable Assy(P5800MP) XXA7390
40 Screw BPZ20P100FTB 88 Spring CBL1512
41 Button(EQ) XAC7116 89 Pin CNV6486
42 Button(1-6) XAC7117 90 Screw(P5800MP) BMZ40P140FTC
91 Holder(P5800MP) CNV7619
43 Button(ENT) XAC7118 92 IC(IC1901) GP1UX30RK
44 Button(PAUSE) XAC7119
45 Button(OPEN) XAC7120 93 IC(IC301) PAL007B
46 Button(AUDIO,FUNC,SW)(P580MP) XAC7134 94 Choke Coil(L901) CTH1280
Button(AUDIO,FUNC,SW)(P5800MP) XAC7113 95 Transistor(Q650,Q911) 2SD2396
96 IC(IC901) NJM2388F84
47 Button(BAND,DISP)(P580MP) XAC7136 F
Button(BAND,DISP)(P5800MP) XAC7115
48 Spring XBH7001
49 Cover XNS7128

DEH-P580MP/XN/UC
5 6 7 8
9
 1 2 3 4

2.3 CD MECHANISM MODULE

DEH-P580MP/XN/UC
10
1 2 3 4
 5 6 7 8
CD MECHANISM MODULE SECTION PARTS LIST
Mark No. Description Part No. Mark No. Description Part No.

1 CD Core Unit(S10.5COMP1) CWX3176 50 Rack CNV8342

2 Connector(CN101) CKS4182 A
3 Connector(CN901) CKS5284 51 Roller CNV8343
4 Screw BMZ20P025FTC 52 Holder CNV8344
5 Screw BSZ20P040FTC 53 Arm CNV8345
54 Guide CNV8347
6 Screw(M2 x 3) CBA1511 55 Arm CNV8348
7 Screw(M2 x 4) CBA1835
8 Washer CBF1038 56 Arm CNV8349
9 ••••• 57 Arm CNV8350
10 Spring CBH2609 58 Clamper CNV8365
59 Arm CNV8386
11 Spring CBH2612 60 Guide CNV8396 B
12 Spring CBH2614
13 Spring CBH2616 61 Arm CNV8413
14 Spring CBH2617 62 Collar CNV8938
15 Spring CBH2620 63 Motor Unit(M2) CXC4026
64 Arm Unit CXC4027
16 Spring CBH2855 65 Chassis Unit CXC4028
17 Spring CBH2937
18 Spring CBH2735 66 Gear Unit CXC4029
19 Spring CBH2854 67 Frame Unit CXC4031
20 Spring CBH2642 68 Motor Unit(M1) CXC6742
69 Screw Unit CXC6359 C
21 Spring CBH2856 70 Screw JFZ20P020FTC
22 Spring CBH2857
23 Spring CBH2860 71 Screw JGZ17P022FTC
24 Spring CBH2861 72 Washer YE20FTC
25 Spring CBL1686 73 Pickup Unit(P10.5)(Service) CXX1942
74 Screw IMS26P030FTC
26 Arm CND1909
27 Frame CND2582
28 Bracket CND2583
29 Arm CND2584
D
30 Lever CND2585

31 Arm CND2586
32 Bracket CND2587
33 Arm CND2588
34 Lever CND2589
35 Holder CNV7201

36 Gear CNV7207
37 Gear CNV7208
38 Gear CNV7209 E
39 Gear CNV7210
40 Gear CNV7211

41 Gear CNV7212
42 Rack CNV7214
43 Arm CNV7216
44 Roller CNV7218
45 Gear CNV7219

46 Guide CNV7361
47 Gear CNV7595 F
48 Guide CNV7799
49 Arm CNV7805

DEH-P580MP/XN/UC
5 6 7 8
11
 1 2 3 4

3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM

3.1 BLOCK DIAGRAM
A

A TUNER AMP ASSY

VDD

TUNPDO
TUNPCK

TUNPDI
7 6 13 5 10 9 8 11 14 18 19 20 21
FM/AM TUNER UNIT

CE2

ROM_VDD

SL

DI
CK
CE1

NC

DO

NC

NC

NC

NC
NC
IC 3 EEPROM IC 5
←
5.0V 5V 3.3V
B
OSC LPF

ANTENNA CN401
AM ANT FMRF
1
1 ATT
2 Rch
24
IC 2
IC 1 2.5V
FM ANT
3 3.3V
ATT Lch
23
FMRF MIXER, IF AMP DET, FM MPX
RF adj
ANT adj

T51 CF52

ASLIN

C
AUDIOGND

IC 4
OSCGND

VDD_3.3

←
RFGND

3.3V 3.3V 2.5V 2.5V

DGND

VCC
NC

EL
2 12 15 22 16 4 17
S
20
MU
15
3.3V REGULATOR NO

TUN L 41 IN2
3.3V 3 IC420 1
VCC8.4V L+ 43
NJM2885DL1-33 IN4
L- 44
IN4
CDL 42 IN3

VST,VCK,VDT
CN101
7 L+
11 L-
92
5 IP-BUS DRIVER LVLINL
IP BUS 1 BUS-
PICKUP UNIT 1 S1

C 8 5 28

(P10.5)(SERVICE) D CD CORE UNIT(S10.5COMP1) IC 101

BUS+ 6 HA12241FP 2 R 27
25
TX
RX MUTE
85

D 8
stb
RX2
CN101 V3R3D
CN651
79 IPPW PEE 24 BZ
LASER CN901 BU
DIODE LD- 142
15 15 LD 31 LOUT CDL
IC201 LOUT 16 5
Q101
Q101
MD
5 5
143
PD UPD63763CGJ SYSPW
1
REFO B.UP 13
VREF 8 133
8 REFOUT RF-AMP,CD DECODER, XIN
AC,BD XTAL 34
HOLOGRAM MP3 , WMA, DECODER, X601
80 11
UNIT
F,E
DIGITAL SERVO / DATA PROCESSOR X201 ASENBO XOUT 15.00MHz
16.93MHz
FOM
3 3
FOM /XTAL 35
FOP
Q102 20
FOP LOCK/RFOK
FOCUS ACT. 2 2 OELPW
MONITOR TOP 56
DIODE TRACKING ACT. 1 1 TOP
TD,FD SD,MD
TOM
4 4
TOM XRST,XASTB,ADO,XCK, SYSTEM CONTROLLER DETACH SENSE SW
LD+ XSO,XSI,WAIT,XINT S802
14 14 IC 601(2/2)
12 CD VDD
PEG146A
39
B.U
FOM dsens
11
FOP
DRIVER Q701 Q
14 VDD
TOP SWVDD 11 10 VDD
13 40
TOM FLPILM
63
SPINDLE IC301 42
MOTOR M BA5835FP LOCK /CD3VON
43 EJTIN
16 14 /RESET RESET 4
SOP CLCONT 21 41 RESET 10 11 CDRST
15 CLCONT 39 CDMUTE
SOM CDMUTE 8 13 ILB CONTRO
18 22 40
LCOP LOEJ LOEJ B.UP Q821
LOAD/ CARRIAGE
M 17 9 IC701 BRST,BRXEN,BSRQ BRST,BRXEN,BSRQ,BDATA,BSCK
E MOTOR LCOM CONT 47
CONTPE5505A BDATA,BSCK Q822
CD CONTROLLER Q650 VD1 7.5V REGULATOR
VD VD1
VD 1 20 B.UP
X1 12
32 Q651
12EJ X701 2 19
31 41
8EJ 4.00MHz ILMPW
30 X2 13
DSCSNS 36
ROT0
42 49 VDCONT VDCONT 35
HOME VDCONT 9 12 ROT1
S904 S905 S901 VDD
12EJ 8EJ HOME
CD3VON
46 38
S903 SWVDD
DSCSNS
Q832

1 33
DPDT
V3R3D
4 IC203
NJM2886DL3-33 3
VD

+3.3V REGULATOR
34
KYDT

BL+B
F 91
A:DEH-P580MP/XN/UC CSENS

B:DEH-P5800MP/XN/UC

DEH-P580MP/XN/UC
12
1 2 3 4
 5 6 7 8

A
CN161
KEYAD 2

KEYD 3 WIRED
1 REMOTE
RESET CN351
1 2 MUTE RL
IC602 VDD RL 2 REAR L
S-80835CNUA-B8U Q351

10 Lch Lch
RESET NON-FAD/SW L
89
KEYAD Q353
2
CE2 69 KEYD CN352
TUNPCE2
CE1 70 FL FL
TUNPDI 98
TUNPCE1 4 FRONT L
TUNPDI
TUNPDO 99
TUNPDO
TUNPCK 100
TUNPCK VDD REGULATOR
Q352 B
Q911
SL 95
SL VDD
Q912

SYSTEM CONTROLLER
IC 601(1/2) 67
DALMON
PEG146A

CN901
BACKUP SENSE B.UP
73 B.UP FUSE
BSENS 1 1 BACK UP
10A
Q931
72 ACC
ASENS 3 3 ACC

ACC SENSE Q941

81 ILM
ISENS 5 5 ILM
Q951
VDD SML ILM SENSE
ASLIN 93 TEL
ASLIN 8 8 TEL
8
57 EMUTE TELIN
TEL IN CCT
C

ELECTRONIC VOLUME/
SOURCE SELECTOR 2 2 GND
20 B.UP
MUTE
15
NOISEDET
POWER AMP 6,20
12 VCC 23 FL-
TUN L 41 IN2L FL- 10 10 FL-
IC201 PreOutL 21 FL+
L+ 43 PML009A F OutL 10 14 IC 301 FL+ 12 12 FL+
IN4L+ FLin PAL007B 3 RL-
L- 44 11 12 RL- 9 9 RL-
IN4L- R OutL RLin 5 RL+
CDL 42 IN3L RL+ 11 11 RL+
SELOutL MUTE STBY B.REM
1 B.UP 22 4 25 B.REM
6 6 B. REM

VST,VCK,VDT
MUTE
Q982
IC131
NJM4558MD
92 7 5
L
MUTE
Q301 SYS +B REGULATOR
85 LEVEL INDICATOR 2 IC 901 1
E VCC8.4V B.UP
NJM2388F84
Q981 E-MUTE
4 D
E 24 BZ621
BUZZER B.UP

1 SYSPW
W
13 B.UP Q851
N BL+B/OELB
X601 Q852
11 15.00MHz
T 6,7 1
IC851
NJM2360M
20
W
DC/DC CONVERTER
DETACH SENSE SW CN801
S802
39 FILM+
s B.UP 5 5
Q801 FILM-
6 6
40
M

N
42 EJECT
8 8 D PANEL UNIT B KEYBOARD UNIT
uGND S1970
9 9
ILB CONTROL EJECT Q1904 LED DRIVER
CN1901
B.UP Q821
ILB+
7 7 4 9
IL+B VOLUME (ENCODER) E
Q822 S1901
ROT0 ROT0 ROT0 2 4 KD1
13 13 9 4
ROT1 12 ROT1 ROT1 1 5 KS2 Q1901
12 7 6
W
41 FONT ROM Q1905 LED DRIVER
3
36 5.1V IC 1990
0
35 3.3V REGULATOR PD8155A:A Q1903
PD8156A:B
ROMCE

1
SWVDD SW+5V 5,4 IC 1902 1 23,33
CS2
CS1

VDD 2 2 2 11 AVCC
RD

Q831 S-818A33AUC-BGN
INVERTER Q1902
ADDRESS

38 12 2 43 14
REMOTE CONTROL
DATA

D SENSOR
3 KEY MATRIX
Q832 OPT IN IC 1901 97 14 60 48 47 46 42 32
DPDT GP1UX30RK 1 5 KEY DATA
33 DPDT
AVCC

VDD1

VDD2

CS0

ILMD

11
CS1

REM
RD

11
CS2

T 10 3 ILLUMINATION
13
XIN
27 KEY/OEL CONTROLLER OEL UNIT
DPDT
11
34 KYDT KYDT 28 XOUT IC1970 IC1971
T 14 14 8 5 KYDT IC 1940 X1940
PEG203A 10.000MHz
10 4,16 5 2,8
OEL DATA
BL+B/OELB
BL+B/OELB 10 10 5 8
91 F
S 4 4 3 10 5.1v
16V
CN1951
CN1950 Q1960
+9.1V
REGULATOR Q1961 +9.1V

DEH-P580MP/XN/UC
5 6 7 8
13
 1 2 3 4

3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE)

A
Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or
"ELECTRICAL PARTS LIST".

Large size
SCH diagram
A-a
A-a A-b

A-a A-b Guide page IP-Bus:

2.20dBs
FM, AM:-24.00dBs

A-a A-b Detailed page

FM,AM:-0.
FM/AM TUNER UNIT

CD:10.01d
IP-Bus:9.3

104:P580MP 104:P5800MP
C

D 104
CN901
C

E EJECT
B CN1901

CD:0.36dBs
CL220SRCTS

For resistors and capacitors in the circuit diagrams, their resistance D PANEL UNIT
values or capacitance values are expressed in codes:

Ex. *Resistors
Code Practical value
123 12k ohms
F 103 10k ohms

*Capacitors
Code Practical value
103 0.01uF
101/10 100uF/10V

A D
DEH-P580MP/XN/UC
14
1 2 3 4
 5 6 7 8

A-b
A TUNER AMP ASSY
NOTE :
Symbol indicates a resistor. The > mark found on some component parts indicates
No differentiation is made between chip resistors and the importance of the safety factor of the part.
discrete resistors. Therefore, when replacing, be sure to use parts of
Symbol indicates a capacitor. identical designation.
No differentiation is made between chip capacitors and
discrete capacitors.

B
>
3A
CD:9.65dBs

FM,AM:-0.90dBs
CD:10.01dBs
IP-Bus:9.30dBs
>
3A

600 H

>
FUSE
CEK1208

10A
BACK UP
D

FM,AM:21.1dBs
CD:36.10dBs E
IP-Bus:36.30dBs

A
DEH-P580MP/XN/UC
5 6 7 8
15
 F
E
B
A

D
C

16
A-a A-b

A-a
A-b

1
1

IP-Bus:
2.20dBs
FM, AM:-24.00dBs

2
2

FM,AM:-0.90dBs
CD:10.01dBs
IP-Bus:9.30dBs

DEH-P580MP/XN/UC
1

FM/AM TUNER UNIT

3
3

104

104:P580MP 104:P5800MP

4
4
 5

5
2

6
6

CN901
C
EJECT
3

B CN1901
CD:0.36dBs
CL220SRCTS

DEH-P580MP/XN/UC
7
7

For resistors and capacitors in the circuit diagrams, their resistance D PANEL UNIT
values or capacitance values are expressed in codes:
4

Ex. *Resistors
Code Practical value
123 12k ohms
103 10k ohms

*Capacitors
Code Practical value
103 0.01uF
8

8
101/10 100uF/10V

A-a A-b

A-a D
A-b

17
E
A

D
C

F
B
 F
E
B
A

D
C

18
A-a A-b

TUNER AMP ASSY

A-b
A
NOTE :

1
1

Symbol indicates a resistor. The > mark found on some component parts indicates
No differentiation is made between chip resistors and the importance of the safety factor of the part.
discrete resistors. Therefore, when replacing, be sure to use parts of
Symbol indicates a capacitor. identical designation.
No differentiation is made between chip capacitors and
discrete capacitors.

>
3A
CD:9.65dBs

2
2

,AM:-0.90dBs
:10.01dBs
Bus:9.30dBs
>
3A

DEH-P580MP/XN/UC
1

3
3

4
600µH
4

>
FUSE
CEK1208 BACK UP
 >
FUSE
CEK1208 BACK UP

10A
5

5
2

6
6

FM,AM:21.1dBs
CD:36.10dBs
IP-Bus:36.30dBs

DEH-P580MP/XN/UC
7
7

4
8

8
A-a A-b

A-b
19
E
A

D
C

F
B
 1 2 3 4

3.3 KEYBOARD UNIT

4R7/10
4R7/16
D CN1951

E
153(B)

B
DEH-P580MP/XN/UC
20
1 2 3 4
 5 6 7 8

B KEYBOARD UNIT

4R7/10

KEY/OEL CONTROLLER C

P580MP

P5800MP
E
153(B)
153(B)

F
OEL UNIT

B
DEH-P580MP/XN/UC
5 6 7 8
21
 1 2 3 4

3.4 CD MECHANISM MODULE(GUIDE PAGE)

A
C-a

C
S

F
C
S

F
B PICKUP UNIT(P10.5)(SERVICE)
$

F
F
T
T

T
F
@
T
F !
F

C T

SWITCHES:
CD CORE UNIT(S10.5COMP1)
S901:HOME SWITCH..........ON-OFF
S903:DSCSNS SWITCH......ON-OFF
S904:12EJ SWITCH.............ON-OFF
S905:8EJ SWITCH...............ON-OFF
The underlined indicates the switch position.

NC
NC
NC
NC
NC
M1 CXC6742 CD DRIVER NC
NC
SPINDLE MOTOR
NC
S
NC
S NC
NC
C NC
# NC
C
NC
NC
M2 CXC4026 T S NC
LOADING/CARRIAGE MOTOR
NC
8 6
NC
F C NC

7
9

4
E NC
NC
F
F
3 T
T

2
C
C
S
S

C
DEH-P580MP/XN/UC
22
1 2 3 4
 5 6 7 8

A
C-b

SIGNAL LINE Decimal points for resistor B

F and capacitor fixed values
FOCUS SERVO LINE are expressed as :
T
TRACKING SERVO LINE 2.2 ← 2R2
C
CARRIAGE SERVO LINE 0.022 ← R022
S
SPINDLE SERVO LINE

C CD CORE UNIT(S10.5COMP1)
0

+ 3.3 V REGULATOR
C

D
NC
NC
NC
NC
NC

NC
NC
NC
NC
NC

NC
NC

NC
NC
NC
NC CD3VON(MCKRQ)
NC SRAMLEVEL2
NC
NC ADENA
NC
NC
NC
NC
NC
NC
NC SRAMLEVEL1
SRAMLEVEL0
5

(S904)
CD CONTROLLER (S905)
NC
NC
E
NC

A CN651

C
DEH-P580MP/XN/UC
5 6 7 8
23
 F
E
B
A

D
C

24
C-a
A-a C-b

C-a
C-b

1
1

T
F

S
C
1

T
F

S
C

2
2

PICKUP UNIT(P10.5)(SERVICE)
$

DEH-P580MP/XN/UC
F
F
T
T

3
3

T
F
@
T
F !
F
T

4
4

SWITCHES:
CD CORE UNIT(S10.5COMP1)
S901:HOME SWITCH..........ON-OFF
S903:DSCSNS SWITCH......ON-OFF
S904:12EJ SWITCH.............ON-OFF
S905:8EJ SWITCH...............ON-OFF

The underlined indicates the switch position.

 SWITCHES:
CD CORE UNIT(S10.5COMP1)
S901:HOME SWITCH..........ON-OFF
S903:DSCSNS SWITCH......ON-OFF
S904:12EJ SWITCH.............ON-OFF
S905:8EJ SWITCH...............ON-OFF
The underlined indicates the switch position.
5

5
2
NC
NC
NC
NC

NC
M1 CXC6742 CD DRIVER NC
SPINDLE MOTOR
NC
S
NC
S NC
NC
C NC
# NC

6
6

C
NC
NC
M2 CXC4026 T S NC
LOADING/CARRIAGE MOTOR
NC
8 6
NC
F C NC

7
9

4
NC
NC
F
F
3 T

DEH-P580MP/XN/UC
T

7
7

S
S
C
C

1
3
8

8
C-a
A-a C-b

C-a
C-b

25
E
A

D
C

F
B
 F
E
B
A

D
C

26
C-a C-b

C-b
1
1

2
2

SIGNAL LINE Decimal points for resistor

F and capacitor fixed values
FOCUS SERVO LINE are expressed as :
T
TRACKING SERVO LINE 2.2 ← 2R2
C 0.022 ← R022
CARRIAGE SERVO LINE
S
SPINDLE SERVO LINE

C CD CORE UNIT(S10.5COMP1)

DEH-P580MP/XN/UC
0

3
3

+ 3.3 V REGULATOR

4
4
 5

5
2
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC CD3VON(MCKRQ)
NC SRAMLEVEL2
NC
NC ADENA
NC

6
6

NC
NC
NC
NC
NC
NC SRAMLEVEL1
SRAMLEVEL0
5

(S904)
CD CONTROLLER (S905)
NC
NC

DEH-P580MP/XN/UC
NC

7
7

A CN651

3
8

8
C-a C-b

C-b
27
E
A

D
C

F
B
 1 2 3 4

- Waveforms Note : 1. The encircled numbers denote measuring points in the circuit diagram.
2. Reference voltage REFO1(1.65 V)
A
1 DSCSNS 5 V/div 500 ms/div 1 DSCSNS 5 V/div 500 ms/div 1 DSCSNS 5 V/div 500 ms/div
2 8SNS 5 V/div 4 CLCONT 5 V/div 2 8SNS 5 V/div
3 12SNS 5 V/div 5 VD 10 V/div 3 12SNS 5 V/div

12 cm CD Loading operation 12 cm CD Loading operation 8 cm CD Loading operation

Ref.: Ref.: Ref.:

GND GND GND

Mode: Mode: Mode:

B Normal Normal Normal

6 SIN 1 V/div 1 s/div 6 SIN 1 V/div 1 s/div 6 SIN 1 V/div 1 s/div

7 CIN 500 mV/div 7 CIN 500 mV/div 7 CIN 500 mV/div
8 TIN 500 mV/div 8 TIN 500 mV/div 8 TIN 500 mV/div

12 cm CD-DA setup operation after loading 12 cm CD-ROM(1 session) setup operation 12 cm CD-ROM(3 sessions) setup operation
after loading after loading

C Ref.: Ref.: Ref.:

REFO REFO REFO

Mode: Mode: Mode:

Normal Normal Normal

9 FIN 200 mV/div 500 ms/div ! TE 500 mV/div 200 ms/div @ FE 500 mV/div 20 ms/div
0 RFOK 2 V/div @ FE 500 mV/div 9 FIN 500 mV/div
6 SIN 2 V/div ! TE 500 mV/div
8 TIN 500 mV/div
12 cm CD-DA Source On setup operation Source On setup operation CD-DA Play operation
D

Ref.: Ref.: Ref.:

REFO REFO REFO

Mode: Mode: Mode:

Normal Normal Normal

@ FE 500 mV/div 20 ms/div # MDX 2 V/div 50 ms/div # MDX 2 V/div 5 µs/div

9 FIN 500 mV/div 6 SIN 200 mV/div 6 SIN 500 mV/div
E
! TE 500 mV/div
8 TIN 500 mV/div
CD-ROM play operation(Regular track Jump) Spindle waveform during play operation Spindle waveform during play operation
(Wider)

Ref.: Ref.: Ref.:

REFO REFO REFO

Mode: Mode: Mode:

Normal Normal Normal

DEH-P580MP/XN/UC
28
1 2 3 4
 5 6 7 8

9 FIN 500 mV/div 200 ms/div ! TE 500 mV/div 2 ms/div $ RFAGC 1 V/div 500 µs/div
@ FE 500 mV/div $ RFAGC 500 mV/div ! TE 500 mV/div A
8 TIN 500 mV/div

Focus Search waveform Track Open waveform 1 Track Jump waveform

Ref.: Ref.: Ref.:

REFO REFO REFO

Mode: Mode: Mode:

TEST TEST TEST

$ RFAGC 1 V/div 500 µs/div $ RFAGC 1 V/div 1 ms/div $ RFAGC 1 V/div 2 ms/div
! TE 500 mV/div ! TE 500 mV/div ! TE 500 mV/div
8 TIN 500 mV/div 8 TIN 500 mV/div 8 TIN 500 mV/div

4 Tracks Jump waveform 10 Tracks Jump waveform 32 Tracks Jump waveform

Ref.: Ref.: Ref.:

REFO REFO REFO
C
Mode: Mode: Mode:
TEST TEST TEST

$ RFAGC 1 V/div 200 ms/div % LOUT 1 V/div 200 µs/div 1 DSCSNS 5 V/div 500 ms/div
! TE 1 V/div ^ ROUT 1 V/div 2 8SNS 5 V/div
7 CIN 500 mV/div 3 12SNS 5 V/div
6 SIN 2 V/div
Search operation(Outter to Inner) Analog audio waveform 12 cm CD Eject operation

D
Ref.: Ref.: Ref.:
REFO AGND GND

Mode: Mode: Mode:

Normal Normal Normal

1 DSCSNS 5 V/div 500 ms/div 1 DSCSNS 5 V/div 500 ms/div 6 SIN 1 V/div 500 ms/div
5 CLCONT 5 V/div 2 8SNS 5 V/div 7 CIN 500 mV/div
4 LOEJ 5 V/div 3 12SNS 5 V/div 8 TIN 500 mV/div
E
12 cm CD Eject operation 8 cm CD Eject operation CD-DA → CD-ROM mode change(Band key)

Ref.: Ref.: Ref.:

GND GND REFO

Mode: Mode: Mode:

Normal Normal Normal

DEH-P580MP/XN/UC
5 6 7 8
29
 1 2 3 4

6 SIN 1 V/div 500 ms/div $ RFAGC 1 V/div 500 µs/div

A 7 CIN 500 mV/div 8 TIN 1 V/div
8 TIN 500 mV/div ! TE 1 V/div
9 FIN 1 V/div
CD-ROM → CD-DA mode change(Band key) Black dot(800 µm) during play

Ref.: Ref.:
REFO REFO

Mode: Mode:
Normal Normal

DEH-P580MP/XN/UC
30
1 2 3 4
5 6 7 8

DEH-P580MP/XN/UC
5 6 7 8
31
 1 2 3 4

4. PCB CONNECTION DIAGRAM

4.1 TUNER AMP ASSY
NOTE FOR PCB DIAGRAMS
A
1.The parts mounted on this PCB
include all necessary parts for
A TUNER AMP ASSY
CORD ASSY
several destination.
For further information for
WIRED
respective destinations, be sure
to check with the schematic dia- REMOTE IP-BUS
gram.
2.Viewpoint of PCB diagrams
Connector Capacitor 1

SIDE A 2

3
B SIDE B
P.C.Board Chip Part

C CN901
20
19
C
15

E
10

5
2
1

DSENS
F

A
DEH-P580MP/XN/UC
32
1 2 3 4
 5 6 7 8

SIDE A A
REAR OUT RCA ANTENNA JACK

FM/AM TUNER UNIT

D

20
19
CN651
15

E
10

5
2
1

D CN1950
F

FRONT A
DEH-P580MP/XN/UC
5 6 7 8
33
 1 2 3 4

A
A TUNER AMP ASSY

TESTIN

PCL

A
DEH-P580MP/XN/UC
34
1 2 3 4
 5 6 7 8

SIDE B A

A
DEH-P580MP/XN/UC
5 6 7 8
35
 1 2 3 4

4.2 KEYBOARD UNIT

A
B KEYBOARD UNIT

AUDIO FUNCTION SW

S1901

SOURCE/VOL

C
DISPLAY BAND
EQ

B KEYBOARD UNIT

B
DEH-P580MP/XN/UC
36
1 2 3 4
 5 6 7 8

SIDE A
A

ENT

PAUSE

C
1 2 3 4 5 6 CLOCK

SIDE B

TP1

E
TP3
TP2

F
D CN1951

B
DEH-P580MP/XN/UC
5 6 7 8
37
 1 2 3 4

4.3 CD CORE UNIT(S10.5COMP1)

C CD CORE UNIT(S10.5COMP1) SIDE A

A
PICKUP UNIT(P10.5)(SERVICE)

A
CN651

REFO1

E
20

HOME

CN901
D

M2
LOADING
/CARRIAGE
MOTOR

M1
E
SPINDLE
MOTOR

IC203 IC301

C
DEH-P580MP/XN/UC
38
1 2 3 4
 5 6 7 8

C CD CORE UNIT(S10.5COMP1) SIDE B

A

8EJ
12EJ
B

DSCSNS

C
DEH-P580MP/XN/UC
5 6 7 8
39
 1 2 3 4

4.4 PANEL UNIT

D PANEL UNIT SIDE A

B CN1901
EJECT

D
D PANEL UNIT SIDE B

A CN801

D
DEH-P580MP/XN/UC
40
1 2 3 4
 5 6 7 8

5. ELECTRICAL PARTS LIST

NOTE:
• Parts whose parts numbers are omitted are subject to being not supplied. A

• The part numbers shown below indicate chip components.

Chip Resistor
RS1/_S___J,RS1/__S___J
Chip Capacitor (except for CQS.....)
CKS....., CCS....., CSZS.....
• The > mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
• Meaning of the figures and others in the parentheses in the parts list.
B
Example) IC 301 is on the point (face A, 91 of x-axis, and 111 of y-axis) of the corresponding
PC board.
IC 301 (A, 91, 111) IC NJM2068V
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
Q 801 (A,103,26) Transistor DTC143EU
Unit Number : XWM7130(P580MP) Q 821 (A,66,13) Transistor 2SD1767
Unit Number : XWM7131(P5800MP) Q 822 (B,77,18) Transistor UMD2N

Unit Name : Tuner Amp Assy Q 831 (B,99,30) Transistor 2SA1576

Q 832 (B,92,21) Transistor DTC114EU
Unit Number : Q 851 (A,17,32) Transistor 2SD1760F5 C
Q 852 (B,29,36) Transistor UMD2N
Unit Name : Keyboard Unit Q 911 (A,6,101) Transistor 2SD2396
Unit Number : CWM9835 Q 912 (B,20,77) Transistor UMD2N
Unit Name : Panel Unit Q 931 (B,50,98) Transistor UMX1N
Q 941 (A,121,71) Transistor DTC114EU
Unit Number : CWX3176 Q 951 (A,46,94) Transistor 2SA1576
Q 981 (B,29,91) Transistor 2SC4081
Unit Name : CD Core
Q 982 (A,137,87) Transistor UMD2N
Unit(S10.5COMP1) D 131 (A,63,66) Diode Network DA204U
D 132 (A,47,70) Diode Network DA204U
D 133 (A,57,61) Diode DAN202U D

A
D 301 (A,98,111) Diode S5688G

D 302 (A,95,111) Diode S5688G

Unit Number : XWM7130(P580MP) D 650 (A,12,70) Diode MTZJA8R2(B)
Unit Number : XWM7131(P5800MP) D 801 (B,103,33) Diode Network DA204U
Unit Name : Tuner Amp Assy D 802 (B,109,30) Diode DAN202U
D 803 (B,113,33) Diode DAP202U
MISCELLANEOUS D 804 (B,113,30) Diode DAN202U
D 805 (B,108,33) Diode DAP202U
IC 101 (A,43,87) IC HA12241FP
D 821 (A,78,13) Diode HZS11L(A1)
IC 131 (A,55,72) IC NJM4558MD
D 851 (A,24,30) Diode MTZJA10(B)
IC 201 (A,81,89) IC PML009A E
D 852 (B,44,23) Diode RB411D
IC 301 (A,92,133) IC PAL007B
IC 420 (A,151,27) IC NJM2885DL1-33
D 901 (A,65,117) Diode S5688G
D 902 (A,69,114) Diode S5688G
IC 601 (A,109,54) IC PEG146A
D 911 (A,18,84) Diode S5688G
IC 602 (A,81,66) IC S-80835CNUA-B8U
D 912 (A,15,79) Diode HZS6L(B1)
IC 851 (B,36,18) IC NJM2360M
D 931 (A,55,108) Diode HZS7L(A1)
IC 901 (A,6,120) IC NJM2388F84
Q 101 (B,41,104) Transistor 2SA1576
D 932 (A,58,101) Diode HZS7L(C3)
D 942 (A,123,79) Diode 1SS133
Q 102 (B,37,102) Transistor DTC114EU
D 951 (A,42,94) Diode DAN202U
Q 301 (A,144,85) Transistor DTC124EU
D 981 (A,20,90) Diode HZS9L(A2)
Q 351 (B,131,119) Transistor UMH3N
D 982 (A,95,71) Diode DAN202U
Q 352 (B,136,128) Transistor UMH3N F
Q 353 (B,161,128) Transistor UMH3N
D 984 (A,122,83) Diode 1SS133
L 101 (A,32,80) Inductor LAU2R2K
Q 650 (A,6,67) Transistor 2SD2396
L 201 (A,74,80) Ferri-Inductor LAU4R7K
Q 651 (B,23,57) Transistor UMD2N
DEH-P580MP/XN/UC
5 6 7 8
41
 1 2 3 4

Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
L 401 (A,156,50) Inductor LAU1R0K R 354 (B,139,119) RS1/16S821J
L 402 (A,148,91) Inductor LAU1R0K
R 355 (B,157,120) RS1/16S821J
A L 403 (B,155,96) Inductor LCTAW220J2520 R 356 (B,144,128) RS1/16S821J
L 405 (A,156,62) Ferri-Inductor LAU4R7K R 357 (B,133,112) RS1/16S223J
L 601 (A,81,59) Ferri-Inductor LAU100K R 358 (B,131,121) RS1/16S223J
L 640 (A,64,49) Inductor LAU2R2K R 359 (B,143,128) RS1/16S223J
L 831 (A,102,22) Inductor LAU2R2K
R 360 (B,126,131) RS1/16S223J
L 852 (A,39,16) Inductor CTF1660 R 361 (B,159,133) RS1/16S223J
L 901 (A,31,107) Choke Coil 600µH CTH1280 R 362 (B,158,128) RS1/16S223J
L 951 (A,53,88) Inductor LAU2R2K R 403 (B,159,70) RS1/16S681J
X 601 (A,93,59) Crystal Resonator 15.000MHz CSS1653 R 404 (A,105,74) RS1/16S681J
S 802 (A,22,9) Switch(DSENS) CSN1039
R 406 (B,156,80) RS1/16S681J
>FU351 (B,127,126) Fuse 3A CEK1286 R 408 (B,156,83) RS1/16S681J
B >FU352 (B,121,116) Fuse 3A CEK1286 R 409 (B,156,85) RS1/16S681J
TU401 (A,162,101) FM/AM Tuner Unit CWE1952 R 411 (B,156,87) RS1/16S681J
> Fuse 10A CEK1208 R 413 (B,157,89) RS1/16S681J
BZ621 (A,137,23) Buzzer CPV1062
R 601 (B,112,61) (P580MP) RS1/16S104J
AR401 (A,160,119) Surge Protector DSP-201M-S00B R 602 (B,107,63) (P5800MP) RS1/16S104J
R 603 (B,112,63) RS1/16S104J
RESISTORS R 605 (B,108,61) RS1/16S104J
R 606 (A,89,66) RS1/16S104J
R 101 (B,37,135) RS1/16S101J R 607 (B,63,57) RS1/16S822J
R 102 (B,37,133) RS1/16S620J
R 103 (B,38,127) RS1/16S101J R 608 (B,97,48) RS1/16S102J
R 104 (A,39,83) RS1/16S102J R 609 (A,93,45) RS1/16S102J
C R 610 (A,91,64) RS1/16S0R0J
R 105 (A,47,83) RS1/16S472J
R 611 (A,93,47) RS1/16S473J
R 106 (A,48,87) RS1/16S472J R 621 (B,132,29) RS1/16S102J
R 107 (B,25,128) RS1/16S821J
R 108 (B,23,128) RS1/16S223J R 631 (A,123,63) RS1/16S104J
R 109 (B,34,105) RS1/16S222J R 640 (B,79,48) RS1/16S104J
R 110 (B,31,121) RS1/16S821J R 641 (B,59,39) RS1/16S682J
R 642 (A,68,44) RS1/16S682J
R 111 (B,29,121) RS1/16S223J R 643 (A,70,42) RS1/16S681J
R 112 (B,27,121) RS1/16S102J
R 113 (B,25,133) RS1/16S102J R 645 (B,63,37) RS1/16S221J
R 114 (B,43,107) RS1/16S223J R 646 (B,84,43) RS1/16S102J
R 115 (B,38,107) RS1/16S472J R 647 (A,75,39) RS1/16S102J
D R 648 (B,92,43) RS1/16S104J
R 131 (A,62,63) RS1/16S563J R 649 (B,84,41) RS1/16S104J
R 132 (A,50,71) RS1/16S563J
R 133 (A,60,71) RS1/16S104J R 650 (A,12,64) RD1/4PU0R0J
R 134 (A,50,74) RS1/16S104J R 651 (A,17,61) RD1/4PU561J
R 135 (A,64,62) RS1/16S474J R 652 (A,17,67) RD1/4PU221J
R 653 (A,76,65) RS1/16S221J
R 136 (A,55,65) RS1/16S474J R 654 (A,77,68) RS1/16S104J
R 161 (A,20,134) RS1/16S102J
R 162 (B,15,132) RS1/16S102J R 666 (B,66,42) RS1/16S104J
R 163 (A,20,132) RS1/16S103J R 667 (B,84,27) RS1/16S102J
R 164 (A,20,130) RS1/16S103J R 668 (B,87,34) RS1/16S102J
R 802 (A,15,24) RS1/16S104J
E
R 201 (A,118,68) RAB4C102J R 803 (A,19,24) RS1/16S102J
R 220 (A,73,97) RS1/16S102J
R 221 (B,74,86) RS1/16S102J R 804 (B,122,24) RS1/16S222J
R 223 (B,98,80) RS1/16S101J R 805 (B,125,24) RS1/16S222J
R 224 (B,90,92) RS1/16S101J R 806 (B,120,24) RS1/16S222J
R 807 (B,118,24) RS1/16S222J
R 225 (B,98,76) RS1/16S101J R 808 (B,112,23) RS1/16S222J
R 226 (B,96,78) RS1/16S101J
R 301 (A,143,81) RS1/16S103J R 809 (B,104,24) RS1/16S222J
R 302 (A,140,82) RS1/16S331J R 810 (B,129,23) RS1/16S102J
R 303 (A,140,84) RS1/16S103J R 811 (B,122,30) RS1/16S102J
R 812 (B,119,29) RS1/16S102J
F R 304 (B,119,128) RS1/16S153J R 813 (A,73,17) RS1/16S1R0J
R 351 (B,145,108) RS1/16S821J
R 352 (B,145,119) RS1/16S821J R 814 (B,108,24) RS1/16S222J
R 353 (B,140,122) RS1/16S821J R 815 (A,104,33) RS1/16S473J
R 816 (B,112,25) RS1/16S473J
DEH-P580MP/XN/UC
42
1 2 3 4
 5 6 7 8

Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
R 817 (B,103,28) RS1/16S473J C 208 (A,90,102) CEJQ4R7M35
R 818 (B,129,26) RS1/16S104J C 209 (A,67,96) CEJQ1R0M50

R 820 (A,105,34) RS1/16S0R0J C 210 (A,60,96) CEJQ1R0M50 A

R 821 (A,53,22) RD1/4PU391J C 211 (A,68,91) CEJQ1R0M50
R 824 (A,77,17) RS1/16S472J C 212 (A,60,86) CEJQ1R0M50
R 825 (A,64,20) RD1/4PU821J C 213 (B,82,81) CKSRYB104K16
R 831 (B,95,28) RS1/16S473J C 214 (A,70,85) CEJQ470M16

R 832 (B,96,25) RS1/16S102J C 215 (A,70,94) CKSRYB105K10

R 833 (B,101,18) RS1/16S222J C 216 (B,82,83) CKSRYB104K16
R 850 (A,32,40) RD1/4PU681J C 217 (A,62,91) CEJQ1R0M50
R 853 (B,33,23) RS1/16S1R0J C 218 (A,60,81) CEJQ1R0M50
R 854 (B,33,21) RS1/16S391J C 220 (B,74,95) CKSRYB152K50

R 855 (B,42,29) RS1/16S121J C 221 (B,76,90) CKSRYB152K50

R 856 (A,50,22) RD1/4PU152J C 223 (B,87,84) CCSRCH120J50 B
R 858 (B,28,22) RS1/16S0R0J C 224 (B,88,90) CCSRCH120J50
R 901 (B,18,99) RS1/16S102J C 225 (B,87,81) CCSRCH120J50
R 902 (B,20,101) RS1/16S103J C 226 (A,95,92) CEJQ100M16

R 912 (B,11,81) RS1/16S222J C 228 (B,87,82) CCSRCH120J50

R 913 (B,12,86) RS1/16S223J C 240 (B,54,85) CKSQYB225K10
R 914 (B,48,94) RS1/16S104J C 309 (A,119,109) CEJQ330M10
R 915 (B,47,98) RS1/16S104J C 311 (A,126,133) CKSQYB225K10
R 916 (A,115,74) RS1/16S104J C 312 (A,126,129) CKSQYB225K10

R 918 (B,11,105) RS1/16S391J C 313 (A,125,109) CEJQ100M16

R 931 (A,51,108) RD1/4PU102J C 314 (B,116,106) CKSRYB474K10
R 932 (B,47,104) RS1/16S472J C 315 (B,119,97) CKSRYB474K10 C
R 933 (B,53,102) RS1/16S473J C 316 (B,116,109) CKSRYB474K10
R 934 (B,55,102) RS1/16S103J C 317 (B,119,101) CKSRYB474K10

R 935 (B,49,104) RS1/16S473J C 318 (B,128,97) CKSRYB474K10

R 936 (B,45,99) RS1/16S104J C 319 (B,110,105) CKSRYB474K10
R 941 (A,64,101) RD1/4PU102J C 320 (B,128,101) CKSRYB474K10
R 942 (A,125,74) RS1/16S103J C 321 (B,110,109) CKSRYB474K10
R 951 (A,61,106) RD1/4PU153J C 351 (A,141,106) CEJQ4R7M35

R 952 (A,43,91) RS1/16S472J C 352 (A,142,117) CEJQ4R7M35

R 953 (A,46,91) RS1/16S472J C 353 (A,138,112) CEJQ4R7M35
R 954 (A,48,94) RS1/16S102J C 354 (A,136,118) CEJQ4R7M35
R 981 (B,24,92) RS1/16S683J C 355 (A,145,111) CEJQ4R7M35 D
R 982 (B,24,90) RS1/16S683J C 356 (A,133,106) CEJQ4R7M35

R 983 (B,24,84) RS1/16S223J C 402 (B,158,56) CKSRYB103K50

R 984 (A,131,88) RS1/16S102J C 405 (B,147,94) CKSRYB103K50
C 406 (A,149,97) CEJQ101M16
CAPACITORS C 408 (B,158,59) CKSRYB103K50
C 411 (B,165,45) CCSRCH101J50
C 101 (B,29,135) CKSRYB104K16
C 102 (A,43,81) CKSRYB473K50 C 415 (A,155,55) CEJQ470M6R3
C 131 (A,62,61) CKSRYB104K16 C 420 (A,149,37) CEJQ470M10
C 132 (A,51,67) CKSRYB104K16 C 422 (A,140,35) CEJQ1R0M50
C 133 (A,62,71) CKSRYB104K16 C 430 (A,102,72) CCSRCH101J50
E
C 601 (A,93,49) CKSRYB103K50
C 134 (A,48,73) CKSRYB104K16
C 135 (A,64,64) CKSRYB474K10 C 602 (A,87,54) CEJQ4R7M35
C 136 (A,52,65) CKSRYB474K10 C 603 (B,84,55) CCSRCH101J50
C 137 (A,64,60) CCSRCH101J50 C 604 (A,70,56) CEJQ2R2M50
C 138 (A,53,65) CCSRCH101J50 C 605 (B,91,58) CCSRCH180J50
C 606 (B,90,54) CCSRCH180J50
C 139 (A,55,76) CKSRYB103K50
C 201 (A,73,75) CEJQ4R7M35 C 643 (B,67,32) CKSRYB221K50
C 202 (A,73,100) CEJQ4R7M35 C 644 (A,59,30) CEJQ101M16
C 203 (A,77,75) CEJQ4R7M35 C 645 (B,43,57) CKSRYB683K16
C 204 (A,77,101) CEJQ4R7M35 C 650 (B,18,58) CKSRYB473K50
C 651 (A,14,55) CEJQ101M16 F
C 205 (A,83,75) CEJQ4R7M35
C 206 (A,83,101) CEJQ4R7M35 C 652 (B,87,30) CKSRYB152K50
C 207 (A,89,75) CEJQ4R7M35 C 653 (B,85,30) CKSRYB152K50
C 654 (B,66,35) CCSRCH470J50
DEH-P580MP/XN/UC
5 6 7 8
43
 1 2 3 4

Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
C 658 (B,83,22) CKSRYB104K16
C 756 (B,88,86) CKSRYB104K16 S 1910 (A,18,9) Push Switch CSG1135
S 1911 (A,156,35) Push Switch CSG1135
A C 803 (A,97,11) CKSRYB104K16 S 1912 (A,157,16) Push Switch CSG1135
C 821 (B,76,14) CKSRYB473K50 S 1913 (A,29,10) Push Switch CSG1135
C 822 (A,75,17) CKSRYB473K50 S 1914 (A,88,6) Push Switch CSG1175
C 832 (B,99,33) CKSQYB105K16
C 851 (B,27,32) CKSRYB104K16 S 1915 (A,99,6) Push Switch CSG1175
S 1916 (A,110,6) Push Switch CSG1175
C 852 (A,27,25) CEJQ470M16 S 1917 (A,121,6) Push Switch CSG1175
C 853 (A,28,18) CEJQ101M16 S 1918 (A,132,6) Push Switch CSG1175
C 854 (B,27,20) CKSRYB104K16 S 1919 (A,143,6) Push Switch CSG1175
C 855 (B,43,17) CCSRCH331J50
C 856 (B,39,21) CKSRYB223K50 S 1920 (A,154,6) Push Switch CSG1175
VR1970 (B,114,11) Semi-fixed 15kΩ(B) CCP1230
C 857 (A,50,13) CEJQ470M25 VR1971 (B,119,11) Semi-fixed 15kΩ(B) CCP1230
B C 901 (A,50,122) 3300µF/16V CCH1486
C 902 (B,60,120) CKSRYB104K25 RESISTORS
C 903 (B,105,145) CKSYB225K16
C 911 (A,25,75) 470µF/16V CCH1331 R 1901 (B,152,31) RS1/16S222J
R 1902 (B,141,37) RS1/16S222J
C 912 (B,29,78) CKSRYB472K50 R 1903 (B,132,14) RS1/16S473J
C 913 (B,13,77) CKSRYB103K50 R 1911 (B,123,12) RS1/16S103J
C 914 (A,14,75) CEJQ470M10 R 1913 (B,157,18) RS1/16S101J
C 922 (B,15,115) CKSRYB103K50
C 923 (A,14,118) CEJQ101M16 R 1914 (B,157,29) RS1/16S103J
R 1915 (B,157,20) RS1/16S2R2J
C 924 (B,28,85) CKSRYB103K50 R 1921 (B,20,8) RS1/16S101J
C 925 (A,26,82) CEJQ221M10 R 1922 (B,25,6) RS1/16S101J
C C 931 (B,45,103) CKSRYB104K16 R 1923 (B,31,6) RS1/16S101J
C 941 (A,130,74) CEJQ1R0M50
C 984 (A,132,81) CEJQ220M16 R 1924 (B,31,9) RS1/16S121J
R 1925 (B,38,6) RS1/16S181J

B
Unit Number :
R
R
R
1926
1927
1928
(B,39,10)
(B,43,6)
(B,117,5)
RS1/16S181J
RS1/16S101J
RS1/16S101J
Unit Name : Keyboard Unit
R 1929 (B,152,6) RS1/16S101J
R 1935 (A,139,31) RS1/16S0R0J
MISCELLANEOUS R 1937 (B,66,12) RS1/16S104J
R 1940 (B,55,32) RS1/16S222J
IC 1901 (A,163,23) IC GP1UX30RK R 1941 (B,103,8) RS1/16S101J
D IC 1902 (B,47,38) IC S-818A33AUC-BGN
IC 1940 (B,86,19) IC PEG203A R 1943 (A,94,32) RAB4C101J
IC 1990 (A,108,24) IC(P580MP) PD8155A R 1944 (A,90,17) RAB4C101J
IC 1990 (A,108,24) IC(P5800MP) PD8156A R 1945 (A,92,28) RAB4C101J
Q 1960 (B,64,34) Transistor 2SC4617 R 1946 (B,100,12) RAB4C101J
R 1947 (A,94,23) RAB4C101J
Q 1961 (B,63,29) Transistor 2SC2411K
D 1913 (A,36,22) LED CL-195SR-CD R 1948 (A,94,19) RAB4C101J
D 1914 (A,47,33) LED CL-195SR-CD R 1949 (B,104,18) RAB4C101J
D 1915 (A,57,22) LED CL-195SR-CD R 1950 (B,101,22) RAB4C101J
D 1916 (A,47,12) LED CL-195SR-CD R 1952 (B,94,31) RS1/16S101J
R 1953 (B,91,31) RS1/16S473J
D 1917 (A,75,6) LED CL-195SR-CD
E D 1918 (A,159,40) LED CL-195SR-CD R 1954 (B,87,30) RAB4C473J
D 1940 (B,67,17) Diode 1SS355 R 1955 (B,82,30) RS1/16S473J
L 1901 (A,138,19) Inductor CTF1617 R 1956 (A,57,36) RS1/16S103J
L 1940 (A,61,37) Inductor CTF1617 R 1957 (B,67,23) RAB4C101J
R 1958 (B,69,19) RS1/16S473J
TH1960 (B,68,35) Thermistor CCX1037
X 1940 (B,74,18) Radiator 10.0MHz CSS1577 R 1959 (B,65,18) RS1/16S154J
S 1901 (A,46,22) Encoder(SOUCE/VOL) XSD7004 R 1960 (B,62,32) RS1/16S333J
S 1902 (A,8,37) Push Switch CSG1135 R 1961 (B,68,33) RS1/16S683J
S 1903 (A,18,37) Push Switch CSG1135 R 1962 (B,73,26) RS1/16S392J
S 1904 (A,28,37) Push Switch CSG1135 R 1963 (B,68,31) RS1/16S393J

S 1905 (A,7,22) Push Switch CSG1185 R 1980 (B,78,8) RS1/16S473J

F
S 1906 (A,14,30) Push Switch CSG1134 R 1991 (B,107,22) RS1/16S101J
S 1907 (A,22,22) Push Switch CSG1185 R 1992 (B,108,24) RS1/16S101J
S 1908 (A,14,15) Push Switch CSG1133 R 1993 (B,94,29) RS1/16S101J
S 1909 (A,68,6) Push Switch CSG1135
DEH-P580MP/XN/UC
44
1 2 3 4
 5 6 7 8

Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
R 1994 (B,94,32) RS1/16S101J Q 701 (B,24,41) Transistor UN2111
X 201 (B,28,57) Ceramic Resonator 16.934MHz CSS1603
R 1995 (B,63,9) RS1/16S473J X 701 (A,24,37) Ceramic Resonator 4.000MHz CSS1652
R 1996 (B,117,16) RS1/16S222J S 901 (A,57,57) Switch(HOME) CSN1067 A
R 1997 (B,113,16) RS1/16S222J S 903 (B,23,78) Switch(DSCSNS) CSN1067
R 1998 (A,80,18) RS1/16S102J
R 1999 (A,78,17) RS1/16S102J S 904 (B,42,87) Switch(12EJ) CSN1068
S 905 (B,28,88) Switch(8EJ) CSN1068
R 2002 (B,75,26) RS1/16S102J
R 2003 (B,78,33) RS1/16S102J RESISTORS
R 2004 (B,79,35) RS1/16S102J
R 2005 (B,84,30) RS1/16S102J R 101 (B,61,92) RS1/10SR2R4J
R 2100 (B,98,7) RS1/16S101J R 102 (B,63,92) RS1/10SR2R4J
R 103 (B,63,89) RS1/10SR2R7J
R 2101 (B,96,9) RS1/16S101J R 104 (A,52,73) RS1/16SS102J
R 2102 (B,105,11) RS1/16S101J R 201 (B,44,57) RS1/16SS102J
R 2103 (A,59,27) RS1/16S101J B
R 202 (A,38,62) RS1/16SS473J
CAPACITORS R 203 (A,37,62) RS1/16SS473J
R 214 (A,46,79) RS1/16SS472J
C 1908 (B,156,24) CKSYF106Z10 R 216 (A,46,81) RS1/16SS472J
C 1909 (B,63,38) CSZSR4R7M16 R 221 (A,44,81) RS1/16SS103J
C 1910 (B,55,36) CSZSR4R7M10
C 1940 (B,55,30) CKSRYB103K50 R 222 (A,45,81) RS1/16SS103J
C 1941 (B,62,18) CKSRYB104K16 R 225 (B,52,78) RS1/16SS103J
R 226 (B,52,77) RS1/16SS393J
C 1942 (B,63,18) CKSRYB105K10 R 227 (A,44,75) RS1/16SS562J
C 1943 (B,97,17) CKSRYB103K50 R 228 (A,46,72) RS1/16SS122J
C 1944 (B,58,28) CSZSR4R7M10
C
C 1972 (B,55,39) CKSRYB104K16 R 229 (A,44,72) RS1/16SS472J
C 1973 (A,125,18) CKSRYB104K25 R 232 (A,46,75) RS1/16SS122J
R 241 (B,26,63) RS1/16SS333J
C 1974 (A,89,34) CKSRYB104K25 R 243 (B,26,62) RS1/16SS333J
C 1975 (A,127,18) CKSRYB104K25 R 245 (B,26,69) RS1/16SS333J
C 1976 (A,80,33) CKSRYB104K25
C 1990 (A,113,16) CKSRYB103K50 R 248 (B,55,74) RS1/16SS105J
C 1991 (A,87,32) CKSRYB104K25 R 307 (A,19,20) RS1/16SS183J
R 308 (A,17,20) RS1/16SS183J
C 1992 (A,83,31) CKSRYB104K16 R 309 (A,18,18) RS1/16SS183J
R 310 (A,17,16) RS1/16SS183J

D
Unit Number : CWM9835
R
R
601
602
(B,30,47)
(B,28,50)
RS1/16S101J
RS1/16S101J
D
R 606 (B,20,54) RS1/16S0R0J
Unit Name : Panel Unit R 701 (B,26,44) RS1/16SS221J
R 707 (B,32,45) RS1/16SS473J
MISCELLANEOUS
R 709 (A,36,35) RS1/16SS222J
D 1970 LED CL220SRCTS R 710 (B,41,46) RS1/16SS102J
S 1970 Push Switch(EJECT) CSG1135 R 712 (A,45,57) RS1/16SS222J
R 1970 RS1/16S101J R 713 (B,40,57) RS1/16SS222J
R 1971 RS1/16S101J R 716 (B,29,37) RS1/16SS472J
R 1972 RS1/16S0R0J
R 724 (B,31,36) RS1/16S473J
C 1970 CKSRYB104K16 R 726 (B,23,47) RS1/16SS103J E
R 727 (B,31,42) RS1/16SS473J

C
Unit Number : CWX3176
R
R
729
730
(B,20,48)
(B,20,46)
RS1/16SS223J
RS1/16SS473J

R 740 (A,38,59) RS1/16SS222J

Unit Name : CD Core R 746 (A,13,38) RS1/16SS104J
Unit(S10.5COMP1) R 750 (A,40,66) RS1/16SS473J
R 902 (A,20,36) RS1/16SS221J
R 905 (A,21,36) RS1/16SS221J
MISCELLANEOUS
R 906 (B,20,36) RS1/16SS221J
IC 201 (B,39,70) IC UPD63763CGJ
R 907 (B,16,62) RS1/16SS0R0J
IC 203 (A,12,16) IC NJM2886DL3-33
R 908 (B,16,64) RS1/16SS0R0J F
IC 301 (A,28,18) IC BA5835FP
R 911 (B,20,32) RS1/16SS0R0J
IC 701 (A,32,48) IC PE5505A
Q 101 (B,60,89) Transistor 2SA1577
CAPACITORS

DEH-P580MP/XN/UC
5 6 7 8
45
 1 2 3 4

Circuit Symbol and No. Part No.

C 103 (B,57,83) CEVW101M16

C 108 (A,47,66) CKSSYB104K10
A C 201 (B,46,56) CKSSYB102K50
C 202 (B,47,58) CKSSYB104K10
C 204 (B,35,48) CEVW220M6R3

C 205 (A,34,63) CKSSYB104K10

C 208 (B,34,54) CKSSYB104K10
C 209 (B,31,57) CKSSYB104K10
C 210 (A,31,66) CKSRYB105K10
C 216 (B,53,77) CKSSYB332K50

C 217 (B,52,79) CKSSYB104K10

C 218 (B,52,76) CKSSYB473K10
C 219 (B,52,74) CKSSYB104K10
B C 220 (A,46,77) CKSSYB182K50
C 221 (B,51,74) CKSSYB104K10

C 222 (A,46,73) CCSSCH560J50

C 223 (A,44,74) CCSSCH4R0C50
C 224 (B,52,68) CKSSYB104K10
C 225 (A,47,67) CKSSYB103K16
C 226 (A,49,67) CCSSCH680J50

C 227 (A,48,65) CCSSCH470J50

C 228 (A,46,62) CKSSYB103K16
C 232 (A,12,31) CKSRYB105K10
C 237 (A,31,67) CKSSYB104K10
C C 239 (A,46,74) CCSSCH220J50

C 246 (A,42,80) CKSSYB104K10

C 250 (A,42,81) CKSRYB102K50
C 251 (A,41,83) CKSRYB102K50
C 303 (A,18,20) CKSSYB472K25
C 304 (A,17,17) CKSSYB103K16

C 307 (A,34,15) CKSSYB104K10

C 308 (A,17,30) CKSRYB105K10
C 601 (B,25,50) CCSRCH102J50
C 602 (B,26,51) CCSRCH102J50
C 701 (B,25,47) CKSSYB104K10
D
C 703 (B,28,42) CKSSYB103K16
C 706 (B,34,43) CKSSYB104K10
C 707 (A,36,57) CKSSYB104K10
C 714 (A,24,41) CKSSYB104K10
C 722 (B,29,45) CKSQYB475K6R3

C 903 (B,14,54) CKSSYB471K50

C 907 (B,14,62) CKSSYB103K16

Miscellaneous Parts List

E Pickup Unit(P10.5)(Service) CXX1942
M 1 Motor Unit(SPINDLE) CXC6742
M 2 Motor Unit(LOADING/CARRIAGE) CXC4026

DEH-P580MP/XN/UC
46
1 2 3 4
 5 6 7 8

6. ADJUSTMENT
6.1 CD ADJUSTMENT
A

1) Cautions on adjustments 2) Test mode

• In this product the single voltage (3.3V) is used for the This mode is used to adjust the CD mechanism module.
regulator. The reference voltage is the REFO1 (1.65V) • To enter the test mode.
instead of the GND. While pressing the 4 and 6 keys at the same time, reset.
If you should mistakenly short the REFO1 with the GND • To exit from the test mode.
during adjustment, accurate voltage will not be obtained, Turn off the ACC and back up.
and the servo’s misoperation will apply excessive shock
to the pickup. To avoid such problems: Notes:
a. Do not mix up the REFO1 with the GND when a. During ejection, do not press any other keys than the
connecting the (-) probe of measuring instruments. EJECT key until the loaded disc is ejected.
Especially on an oscilloscope, avoid connecting the (-) b. If you have pressed the (→) key or (←) key during focus B
probe for CH1 to the GND. search, turn off the power immediately to protect the
b. In many cases, measuring instruments have the same actuator from damage caused by the lens stuck.
potential as that for the (-) probe. Be sure to set the c. For the TR jump modes except 100TR, the track jump
measuring instruments to the floating state. operation will continue even if the key is released.
c. If you have mistakenly connected the REFO1 to the GND, d. For the CRG move and 100TR jump modes, the tracking
turn off the regulator or the power immediately. loop will be closed at the same time when the key is
released.
• Before mounting and removing filters or leads for e. When the power is turned off and on, the jump mode
adjustment, be sure to turn off the regulator. is reset to the single TR (91), the RF amp gain is set to 0dB,
and the auto-adjustment values are reset to the default
• For stable circuit operation, keep the mechanism settings.
operating for about one minute or more after the C
regulator is turned on.

• In the test mode, any software protections will not

work. Avoid applying any mechanical or electrical
shock to the mechanism during adjustment.

• The RFI and RFO signals with a wide frequency range

are easy to oscillate. When observing the signals,
insert a resistor of 1k ohms in series.

• The load and eject operation is not guarantied with the

D
mechanism upside down. If the mechanism is blocked
due to mistaken eject operation, reset the product or
turn off and on the ACC to restore it.

DEH-P580MP/XN/UC
5 6 7 8
47
 1 2 3 4

- Flow Chart
[Key] [4] + [6] + Reset or
[4] + [6] + BU + ACC
Contents Test Mode In

A Display

[CD] or [SOURCE]
Source On

TRK MIN SEC

[BAND] [3] [2] [4]

Power On Power On RF AMP *1 SPINDLE *9
(T.Offset is adjusted) (T.Offset is not adjusted) Gain switching Speed switching
TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC
00 00 00 99 99 99 GG GG GG SP SP SP

[BAND] [3] [6] [1] [>] [<] [2]

[5]
Power Off Focus Close Focus Mode switching Tracking Servo CRG + CRG - Self-adjusting
B S curve check *2 Close *8 *8 switching *3 Gop Mode *10
Gop Mode switching
TRK MIN SEC TRK MIN SEC TRK MIN SEC 00 00 00 00 00 00 00 00 00 TRK MIN SEC
TRK MIN SEC
91 91 91 0X 0X 0X or 99 99 99 or 99 99 99 or 99 99 99 ?? ?? ??
OL OL OL

[BAND] [1] [6] [3] [>] [<] [2]

Power Off T.Close & AGC T.Close RF AGC / CRG + CRG - T.Balance adjustment /
Applicable servomechanism Applicable servomechanism RF AGC coefficient display T.BAL coefficient display
TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC 8X 8X 8X 8X 8X 8X TRK MIN SEC
?tr ?min ?sec ?tr ?min ?sec ?? ?? ?? or 9X 9X 9X or 9X 9X 9X ?? ?? ??

[BAND] [1] [3] [6] *5 [>] [<] [2]

Power Off F,T,RF AGC*7 F,T AGC / F.Bias CRG/TR jump CRG/TR Jump + CRG/TR Jump - Tracking Open
F.Bias display switching RF AGC value switching *4 *4
TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC 8X 8X 8X
?? ?? ?? ?tr ?min ?sec ?tr ?min ?sec ?tr ?min ?sec ?tr ?min ?sec or 9X 9X 9X

C *6

[BAND] [2]
Power Off Tracking Open

TRK MIN SEC 8X 8X 8X

or 9X 9X 9X

*1) TYP → + 6 dB → + 12 dB Operation

TRK MIN SEC TRK
06MIN06SEC06 TRK
12MIN12SEC12 [Key] Test Mode
[BAND] Power On/Off
[>] CRG + / TR Jump +
*2) Focus Close → S Curve check setting → F EQ measurement setting (Direction of the external surface)
TRK
00MIN00SEC00 TRK
01MIN01SEC01 TRK
02MIN02SEC02 [<] CRG - / TR Jump -
(TRK99MIN99SEC99) (Direction of the internal surface)
D
[1] T. CLS & AGC & Applicable servomechanism /
AGC,AGC display setting
*3) F.Offset Display → RF.Offset → T.Offset Display → Switch to the [2] RF Gain switching / Offset adjustment display /
order of the original display
T.Balance adjustment / T. Open
[3] F. Close,S Curve / Rough Servo and RF AGC /
*4) 1TR/4TR/10TR/32TR/100TR F,T,RF AGC
*5) Single → 4TR → 10TR → 32TR → 100TR → CRG Move [4] SPDL 1X/2X switching
9x(8x):91(81) 92(82) 93(83) 94(84) 95(85) 96(86) As for the double speed(2x), audio output cannot be
supported.
*6) Only at the time of CRG move, 100TR jump [5] Error Rate measurement
ON : ERR 30Counts Start
BER display data[%]
*7) TRK/MIN/SEC → F.AGC → T.AGC Gain → F.Bias → RF AGC
E [6] F. Mode switching / Tracking Close / CRG•TR
Jump Switching
*8) CRG motor voltage = 2 [V]

*9) TYP (1X) → 2X → 1X *10) OFF(TYP) → FORCUS → TRACKING

TRK MIN SEC TRK
22MIN22SEC22 TRK
11MIN11SEC11 TRK MIN SEC TRK
70MIN70SEC70 TRK
71MIN71SEC71

• As for the double speed (2x), audio output cannot be supported

*) • After the [Eject] key is pressed keys other than the [Eject] key should not be pressed, until disc ejection is complete.
• When the key [2] or [3] is pressed during the Focus Search, the power supply should be immediately turned off (otherwise the lens
sticks to Wall, causing the actuator to be damaged).
F • In the case of TR jump other than to 100TR, the function shall continue to be processed even if the TR jump key is released. As for
the CRG Move and 100TR Jump, the mechanism shall be set to the Tracking Close mode when the key is released.
• When the power is turned on/off the jump mode is reset to the Single TR (91) while the gain of the RFAMP is reset to 0 dB. At the
same time all the self-adjusting values shall return to the default setting.

DEH-P580MP/XN/UC
48
1 2 3 4
 5 6 7 8

6.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT

• Note :
The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mechanism
module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted PU
unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if the
PU unit must be changed, the grating should be checked using the procedure below.

• Purpose :
To check that the grating is within an acceptable range when the PU unit is changed.

• Symptoms of Mal-adjustment : B
If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform
track search operations, or taking a long time for track searching.

• Method :
• Measuring Equipment • Oscilloscope, Two L.P.F.
• Measuring Points • E, F, REFO1
• Disc • TCD-782
• Mode • TEST MODE

CD CORE UNIT(S10.5COMP1)
C

L.P.F.
REFO1
E Xch Ych
E 100kΩ
F
Oscilloscope
VREF 390pF

F 100kΩ

VREF 390pF

L.P.F. D

• Checking Procedure
1. In test mode, load the disc and switch the 3V regulator on.
2. Using the → and ← buttons, move the PU unit to the innermost track.
3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance
adjustment the display should now read "81". Press key 3. The display will change, returning to "81" on the
fourth press.
4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase
E
difference is within 75° . Refer to the photographs supplied to determine the phase angle.
5. If the phase difference is determined to be greater than 75° try changing the PU unit to see if there is any
improvement. If, after trying this a number of times, the grating angle does not become less than 75° then the
mechanism should be judged to be at fault.
• Note
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be
seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the
average angle.
• Hint
Reloading the disc changes the clamp position and may decrease the "wobble".

DEH-P580MP/XN/UC
5 6 7 8
49
 1 2 3 4

Grating waveform Ech → Xch 20mV/div, AC

Fch → Ych 20mV/div, AC
A
0° 30°

45° 60°

75° 90°

DEH-P580MP/XN/UC
50
1 2 3 4
 5 6 7 8

6.3 ERROR MODE

- Error Messages
If a CD is not operative or stopped during operation due to an error, the error mode is turned on and cause(s) of A
the error is indicated with a corresponding number. This arrangement is intended at reducing nonsense calls from
the users and also for facilitating trouble analysis and repair work in servicing.

(1) Basic Indication Method

1) When SERRORM is selected for the CSMOD (CD mode area for the system), error codes are written to DMIN
(minutes display area) and DSEC (seconds display area). The same data is written to DMIN and DSEC. DTNO
remains in blank as before.

2) Head unit display examples

B
Depending on display capability of LCD used, display will vary as shown below. xx contains the error number.

8-digit display 6-digit display 4-digit display

ERROR–xx ERR–xx E–xx

(2) Error Code List

Code Class Displayed error code Description of the code and potential cause(s)
10 Electricity Carriage Home NG CRG can't be moved to inner diameter.
SERVO LSI Com- CRG can't be moved from inner diameter.
munication Error → Failure on home switch or CRG move mechanism. C
Communication error between microcomputer and SERVO LSI.
11 Electricity Focus Servo NG Focusing not available.
→ Stains on rear side of disc or excessive vibrations on REWRITABLE.
12 Electricity Spindle Lock NG Spindle not locked. Sub-code is strange (not readable).
Subcode NG → Failure on spindle, stains or damages on disc, or excessive vibrations.
A disc not containing CD-R data is found.
Turned over disc are found, though rarely.
CD signal error.
17 Electricity Setup NG AGC protection doesn't work. Focus can be easily lost.
→ Damages or stains on disc, or excessive vibrations on REWRITABLE. D

30 Electricity Search Time Out Failed to reach target address.

→ CRG tracking error or damages on disc.
44 Electricity ALL Skip Skip setting for all track.
(CD-R/RW)
50 Mechanism CD On Mech Error Mechanical error during CD ON.
→ Defective loading motor, mechanical lock and mechanical sensor.
A0 System Power Supply NG Power (VD) is ground faulted.
→ Failure on SW transistor or power supply (failure on connector).
Remarks: Mechanical errors are not displayed (because a CD is turned off in these errors). E
Unreadable TOC does not constitute an error. An intended operation continues in this case.
Upper digits of an error code are subdivided as shown below:
1x: Setup relevant errors, 3x: Search relevant errors, Ax: Other errors.

DEH-P580MP/XN/UC
5 6 7 8
51
 1 2 3 4

6.4 SYSTEM MICROCOMPUTER TEST PROGRAM

A
- PCL output
In the normal operation mode (with the detachable panel installed, the ACC switched ON, the standby mode
cancelled), shift the TESTIN IC601 (Pin 86) terminal to H.
The clock signal is output from the PCL terminal IC601 (Pin 37).
The frequency of the clock signal is 468.75 kHz that is one 32th of the fundamental frequency.
The clock signal should be 468.75 kHz ± 19 Hz.
If the clock signal is out of the range, the X'tal (X601) should be replaced with new one.

6.5 OEL ADJUSTMENT

Adjustment point
KEYBOARD UNIT(SIDE B)

TP1

TP3
TP2

Digital Multi-Meter

<When the OEL Unit has been replaced>

1. Use VR1970 to adjust the resistance between TP1 and TP3 to 6.2 kΩ.
2. Use VR1971 to adjust the resistance between TP2 and TP3 to 6.2 kΩ.
E

DEH-P580MP/XN/UC
52
1 2 3 4
 5 6 7 8

7. GENERAL INFORMATION
7.1 DIAGNOSIS
7.1.1 DISASSEMBLY
A

- Removing the Case (not shown)

1. Remove the Case.

- Removing the CD Mechanism Module (Fig.1) CD Mechanism Module

1 Remove the four screws.

B
Disconnect the connector and then remove the 1
CD Mechanism Module.
1

- Removing the Grille Assy (Fig.1)

2 Remove the two screws and then remove

the Grille Assy.
1
2 C
1 2

Grille Assy Fig.1

- Removing the Tuner Amp Assy (Fig.2)

1 Remove the screw.

2
2 D
2
2 Remove the three screws.

3 Straighten the tabs at three locations

indicated.

4 Remove the screw and then remove

4
the Tuner Amp Assy.
1

3 3 3

Tuner Amp Assy Fig.2

F

DEH-P580MP/XN/UC
5 6 7 8
53
 1 2 3 4

- How to hold the Mechanism Unit

1. Hold the Upper and Lower Frames.
2. Do not hold the front portion of the Upper
A Frame, because it is not very solid.

Do not squeeze this area.

- Removing the Upper and Lower Frames

1. With a disc inserted and clamped in the a
B
mechanism, remove the two Springs (A), Upper Frame
the six Springs (B), and the four Screws. B
2. Turn the Upper Frame using the part "a" as
C
a pivot, and remove the Upper Frame.
3. While lifting the Carriage Mechanism,
B
remove it from the three Dampers.
Caution: When assembling, be sure to apply
some alcohol to the Dampers and assemble B
the mechanism in a clamped state.

B
B

A
Damper
D Damper
A
Carriage Mechanism Lower Frame

DEH-P580MP/XN/UC
54
1 2 3 4
 5 6 7 8

- How to remove the CD Core Unit

1. Apply Shorting Solder to the flexible cable of Shorting Solder
the Pickup, and disconnect it from the
connector. A
2. Unsolder the four leads, and loosen the
Screw.
3. Remove the CD Core Unit.
Caution: When assembling the CD Core Unit,
assemble it with the SW in a clamped state
so as not to damage it.

Screw

B
CD Core Unit

Solder

- How to remove the Pickup Unit

1. Make the system in the carriage mechanism mode, and have it clamped.
2. Remove the CD Core Unit and remove the leads from the Inner Holder.
3. Remove the Poly Washer, Change Arm, and Pickup Lock Arm.
4. While releasing from the hook of the Inner Holder, lift the end of the Feed Screw. C
Caution: When assembling, move the Planet Gear to the load/eject position before setting the Feed Screw in the Inner
Holder.
Assemble the sub unit side of the Pickup, taking the plate (Chassis) in-between. When treating the leads of the Load
Carriage Motor Assy, do not make them loose over the Feed Screw.

Poly Washer Change Arm

Pickup Lock Arm

Inner Holder
Feed Screw

Planet Gear
Pickup Rack

Chassis

Pickup

DEH-P580MP/XN/UC
5 6 7 8
55
 F
E
B
A

D
C

56
REAR OUTPUT

1
1

SW F

1 0 A

2
2

ANTENNA JACK WIRED REMOTE

CONTROL

SUBWOOFER OUTPUT
NON FADING OUTPUT

FRONT OUTPUT
7.1.2 CONNECTOR FUNCTION DESCRIPTION

DEH-P580MP/XN/UC
3
3

1. BUS+
2. GND
3. GND
16 14 12 10 8 6 4 2 4. NC
5. BUS- 8 9 10 11
15 13 11 9 7 5 3 1 5 6 7
6. GND
7. BUS L+ 1 2 3 4
8. ASENB
1 B.UP 9 RL- 9. BUS R+
2 GND 10 FL- 10. BUS R-
3 ACC 11 RL+ 11. BUS L-
4 NC 12 FL+
5 ILM 13 RR-

4
4

6 B.REM 14 FR-
7 NC 15 RR+
8 TEL 16 FR+
 5 6 7 8

7.2 IC
- Pin Functions (UPD63763CGJ)
Pin No. Pin Name I/O Function and Operation A
1 D.VDD Power supply for digital circuits
2 D1.GND Ground for 1.6 V digital circuits
3 reset I Input of reset
4-8 AB12-8 I Address bus 12-8 from the microcomputer
9-16 AD7-0 I/O Address/data bus 7-0 to the microcomputer
17 cs I Chip selection
18 ASTB I Address strobe
19 read I Control signals(read)
20 write I Control signals(write)
21 wait O Control signals(wait)
22 INTQ O Interruption signals to the external microcomputer
23,24 IFMODE0,1 I Switching the microcomputer I/F 0, 1 B
25 D1.VDD Power supply for 1.6 V digital circuits
26 DA.VDD Power supply for DAC
27 ROUT O Output of audio for the right channel
28 DA.GND Ground for DAC
29 REGC Connected to the capacitor for band gap
30 DA.GND Ground for DAC
31 LOUT O Output of audio for the left channel
32 DA.VDD Power supply for DAC
33 X.VDD Power supply for the crystal oscillator
34 XTAL I Connected to the crystal oscillator(16.9344 MHz)
35 xtal O Connected to the crystal oscillator(16.9344 MHz)
36 X.GND Ground for the crystal oscillator C
37 VDDREG15 Control of 1.6 V regulator
38 PWMSW0 I Setup 0 for PWM output(SD, MD)
39-41 TEST3-1 I Connected to Ground
42 PWMSW1 I Setup 1 for PWM output(FD, TD)
43 TESTEN I Connected to Ground
44 D1.GND Ground for 1.6 V digital circuits
45 DIN I Input of audio data
46 DOUT O Output of audio data
47 SCKIN I Clock input for audio data
48 SCKO O Clock output for audio data
49 LRCKIN I Input of LRCK for audio data
D
50 LRCK O Output LRCK for audio data
51 xtalen I Permission to oscillate 16.9344 MHz
52 D1.VDD Power supply for 1.6 V digital circuits
53 RFCK/HOLD O Output of RFCK/HOLD signal
54 WFCK/MIRR O Output of WFCK/MIRR signal
55 PLCK/RFOK O Output of PLCK/Output of RFOK
56 LOCK/RFOK O Output of LRCK/Output of RFOK
57 C1D1/C8M/(RA13) O Information on error correction/C8M : 8 MHz
58 C1D2/C16M/(RA12) O Information on error correction/C16M : 16 MHz
59 C2D1/RMUTE O Information on error correction/Mute for Rch
60 C2D2/LMUTE O Information on error correction/Mute for Lch
61 C2D3/SHOCK O Information on error correction/Detection of vibration E
62 D1.GND Ground for 1.6 V digital circuits
63 C33M O Output of 33.8688 MHz(CLK for SDRAM)
64 (rcs) O DRAM cs
65 RA11 O Output of DRAM address 11
66 (CKE) O Output of DRAM CKE
67 ras O Output of DRAM ras
68 cas)(LDQM) O Output of DRAM lower cas(LDQM)
69 cas!(UDQM) O Output of DRAM upper cas(UDQM)

DEH-P580MP/XN/UC
5 6 7 8
57
 1 2 3 4

Pin No. Pin Name I/O Function and Operation

70 we O Output of DRAM we
71 oe(cas) O Output of DRAM oe(cas)
A 72 D.GND Ground for digital circuits
73-88 RDB0-15 I/O Input/output of DRAM data0-15
89-99 RA0-10 O Output of DRAM address0-10
100 D.VDD Power supply for digital circuits
101 FD+ O Output of focus drive PWM +
102 FD- O Output of focus drive PWM -
103 TD+ O Output of tracking drive PWM +
104 TD- O Output of tracking drive PWM -
105 SD+ O Output of thread drive PWM +
106 SD- O Output of thread drive PWM -
107 MD+ O Output of spindle drive PWM +
108 MD- O Output of spindle drive PWM -
B
109 REFOUTSV O REFOUT for servo
110 AD.VDD Power supply for ADC
111 EFM O Output of EFM signals
112 ASY I Input of asymmetry
113 ATEST O Analog tests
114 RFI I Input of RF
115 AD.GND Ground for the analog system
116 AGCO O Output of RF
117 C3T O Connection to the capacitor for detecting 3T
118 AGCI I Input of AGC
119 RFO O Output of RF(AGC)
C 120,121 EQ2,1 I Equalizer 2, 1
122 RF2- I Reversal input of RF2
123 RF- I Reversal input of RF
124 A.GND Ground for the analog system
125 A I Input of A
126 C I Input of C
127 B I Input of B
128 D I Input of D
129 F I Input of F
130 E I Input of E
131 VREFIN I Input of reference voltage
132 A.VDD Power supply for the analog system
D 133 REFOUT O Output of reference voltage
134 REFC I Connected to the capacitor for output of REFOUT
135 FE- I Reversal input of FE
136 FEO O Output of FE
137 ADIN I Input of FE, TE A/D converter
138 TE- I Reversal input of TE
139 TEO O Output of TE
140 TE2 O TE2
141 TEC I TEC
142 LD O Output of LD
143 PD I Input of PD
144 D.GND Ground for digital circuits
E

* UPD63763CGJ
IC's marked by * are MOS type.
109
144

Be careful in handling them because they are very

1 108 liable to be damaged by electrostatic induction.

36 73
F
37

72

DEH-P580MP/XN/UC
58
1 2 3 4
 5 6 7 8

- Pin Functions (PE5505A)

Pin No. Pin Name I/O Format Function and Operation
1 AVREF A power supply / Positive power supply(5V)
2 AVSS A power supply GND A
3 testin I Chip check test program starting input
4 CLAMP Not used
5 EVDD E power supply / Positive power supply
6 FMODE For flash rewriting / L : flash rewriting mode
7 FLRQ For flash rewriting / Reset voltage control
8 IC/FLMD0 IC : VSS direct connection/FLMOD0 : Pull-down
9 VDD Positive power supply(5V)
10 REGC Connected to the capacity stabilizing output of the regulator
11 VSS GND
12 X1 I Oscillator connection for mainclock
13 X2 Oscillator connection for mainclock
B
14 reset I System reset input
15 XT1 I Connected to the oscillator for subclock(connected to VSS via the resistor)
16 XT2 Connected to the oscillator for subclock(Open)
17 PULLDOWN I Connected to EVDD or EVSS via the resistor
18 ejsw Not used
19 xint I C CD LSI interruption signal input
20 NC Not used
21 brst I Bus reset input
22 BSI I Bus serial data input
23 BSO O C Bus serial data output
24 bsck I/O /C Bus serial clock input/output
25 FTxD O C For flash rewriting(transmitted signal) C
26 FRxD I For flash rewriting(received signal)
27 BRXEN I/O /C Bus RX enable input/output
28 bsrq I/O /C Bus serial clock input/output
29 dspok Not used
30 DSCSNS I C Disc state sense input
31 8EJ(S905) I C input of detection of 8 cm disc ejection
32 12EJ(S904) I C input of detection of 12 cm disc ejection
33 EVSS E power supply GND
34 EVDD E power supply / Positive power supply
35,36 SRAMLEVEL0,1 O SRAM level meter output
37 EMPH O C Emphasis information output
38 emph Not used D
39 CDMUTE Not used
40 LOEJ Not used
41 CLCONT O Driver input switching output
42 HOME I Home SW sense input
43 adena O C A/D reference voltage supply control output
44 LRCKOK O C (DOUT mute output)
45 SRAMLEVEL2 O C SRAM level meter output
46 CD3VON(MCKRQ) O C CD + 3.3 V power supply control output(Digital output : MCKRQ)
47 CONT O C Servo driver power supply control output
48 xrst O C CD LSI reset control output
49 VDCONT O C VD power supply control output
E
50 xsi I CD LSI serial data input
51 xso O C CD LSI serial data output
52 xck O C CD LSI serial clock output
53 xwait I C CD LSI wait control signal input
54 XASTB O C CD LSI address strobe output
55 AD0 O C Address/data Bus 0
56 INT Not used

DEH-P580MP/XN/UC
5 6 7 8
59
 1 2 3 4

Pin No. Pin Name I/O Format Function and Operation

57 ROMDATA I/O E2PROM data input/output
58 ROMCK O E2PROM clock output
A 59 ROMCS O C E2PROM chip selection output
60,61 NC Not used
62 CLKOUT Not used
63 LOCK I Spindle lock input
64-68 NC Not used
69 BVSS B power supply GND
70 BVDD B power supply / Positive power supply
71-75 NC Not used
76 FLMD1 I/O /C Address/Data Bus 5
77-90 NC Not used
91-93 A/D Not used
94 csens Not used
B
95 TYPE_A/D Not used
96,97 NC Not used
98 TEMP Not used
99 VDSENS I VD power supply short sense input
100 DSCSNS Not used

* PE5505A
Format meaning
100

76

C C MOS
1 75

C
NJM2886DL3-33

25 51
Thermal
Protection
26

50

Bandgap
Reference
-+
D

1 2 3 4 5

CONTROL VIN GND VO NC

E GP1UX30RK
- Block Diagram - Pin Layout

RL

Amp Limiter B.P.F Demodulato Integrator Comparator

1 2 3
2 3 1 vout GND VCC
F GND VCC vout

DEH-P580MP/XN/UC
60
1 2 3 4
 5 6 7 8

- Pin Functions (PEG203A)

Pin No. Pin Name I/O Format Function and Operation
1 NC Not used
2 ROMDT I/O Not used
A
3 ROMCK O Not used
4 romcs O Not used
5 REM I Remote control reception
6 BYTE I External data bus width change input
7 CNVSS I Processor mode change input
8,9 NC Not used
10 reset I Reset
11 XOUT O Radiator(10 MHz)
12 VSS1 GND
13 XIN I Radiator(10 MHz)
14 VDD1 Power supply
15 nmi I NMI input B
16-19 kd!-$ I C Key data input 1-4
20 CKC O C Cathode driver pulse
21 NC Not used
22 CKA O C Anode driver pulse
23 NC Not used
24 LS O C Line synchronous signal
25 NC Not used
26 CKD O C Data transfer and driver clock
27 DPDT I N Display data communication
28 KYDT O N Display data communication
29 DA2 O C Display data MSB
30 NC Not used C
31 CLK1 I C UART1 clock input
32 ILMD O C Dual illumination
33 DA1 O C Display data LSB
34 NCB Not used
35 CLK0 I C UART0 clock input
36 NC Not used
37 rdy I C Ready
38 NC Not used
39 hold I C Hold input
40 NC Not used
41 cs#r Not used
42 rd O C Read strobe D
43-44 NC Not used
45 cs# Not used
46,47 cs@,! O C Bank address
48 cs) O C External ROM chip select
49 A19 O C Address bus 19 bit
50 NC Not used
51-59 A17-9 O C Address bus 17-9 bit
60 VDD2 Power supply
61 A8 O C Address bus 8 bit
62 VSS2 GND
63-69 A7-1 O C Address bus 7-1 bit E
70 NC Not used
71-86 D15-0 I/O C Data bus 15-0 bit
87 NC Not used
88-92 ks@-^ O C key strobe 2-6
93 NC Not used
94 AVSS A/D converter GND input
95 NC Not used
96 VREF I A/D converter reference voltage
97 AVCC A/D converter power supply input
98 flbusy Not used
99 NC Not used
100 FWRST I Restart signal for IC rewriting F

DEH-P580MP/XN/UC
5 6 7 8
61
 F
E
B
A

D
C

62
25
26 1 100

1
1

* PD8155A
* PEG203A

HA12241FP
NC 1 44 NC
A18 2 43 A19
50 76
A17 3 42 A8
A7 4 41 A9

1
8
51
75

S1
BIAS
stb
A6 5D15/A-1 : Data output/Address input 40 A10
A5 6A0 to A19 : Address input 39 A11
D0 to D14 : Data output
A4 7 38 A12
ce : Chip enable

2
2

A3 8 oe : Output enable 37 A13

A2 9 byte : Mode switch 36 A14

2
7
VCC : Power supply voltage

VCC

R out
A1 10 35 A15
VSS : GND

-
+
A0 11 NC : Non connection 34 A16

OUTPUT
ce 12 33 byte

RECEIVER
VSS 13 32 VSS

3
6
oe 14 31 D15/A-1

S2
+BUS

DEH-P580MP/XN/UC
D0 15 30 D7

COM
-
+
(current)
DRIVER
OUTPUT
D8 16 29 D14
D1 17 28 D6

3
3

D9 18 27 D13

4
5
D2 19 26 D5

GND
-BUS
D10 20 25 D12
N
C

D3 21 24 D4
Format

D11 22 23 VCC
C MOS
meaning

4
4

Nch open drain

 8 7 6 5
63
DEH-P580MP/XN/UC
F
E
sw_vcc

Protector;
Over voltage
1

TAB Reference
amp_vcc
Stand-by
2

P-GND2 Circuit
3
+-

OUT2-
Offset Protector;
4

STBY Detection Thermal

5
-+

D OUT2+
6
VCC
7
+-

OUT1-
Offset

8
P-GND1 Detection

9
-+

OUT1+
SVR

10
IN1

11
IN2
Protector;
C
S-GND

12 13
Short circuit
amp_vcc

IN4

14
IN3

15
AC-GND

16
+-
OUT3+

17
Offset
P-GND3 Detection

18
-+
OUT3-

19
B VCC

+-
OUT4+

20 21
Offset
MUTE Detection

22
-+
OUT4-

23
P-GND4
SWITCH

24 25
Protector;
Over current limit

stby
sw_vcc
Mute circuit
A
PAL007B
8 7 6 5
 1 2 3 4

- Pin Functions (PEG146A)

Pin No. Pin Name I/O Function and Operation
1 SYSPW O System power control output
A 2 KEYD I Wired remote control : Key data input
3 NC Not used
4 rst@ O Reset output for CD mechanism
5 NC Not used
6 BYTE I External data bus width change input
7 CNVSS I Processor mode change input
8 TELIN I TEL : Cellular mute input
9 NC Not used
10 reset I Reset input
11 XOUT O Clock output
12 VSS I GND
13 XIN I Clock input
B
14 VCC I Power supply input
15 NMI I Not used
16 rck Not used
17 ldet Not used
18,19 NC Not used
20 OELPW O OEL power supply output
21 NC Not used
22 brxen I/O P-BUS : RX enable input/output
23 brst O P-BUS : Reset output
24 PEE O PEE sound output
25 RX2 I IP-BUS : Input 2
C 26 bsrq I P-BUS : Slave service request input
27 RX I IP-BUS : Data input
28 TX O IP-BUS : Data output
29 BSO O P-BUS : Serial output data
30 BSI I P-BUS : Serial input data
31 BSCK O P-BUS : Serial clock output
32 NC Not used
33 DPDT O GRILLE : Data output
34 KYDT I GRILLE : Data input
35,36 ROT1,0 I Rotary encoder pulse input1,0
37 PCL O Output for clock adjustment
38 SWVDD O GRILLE : Chip enable output
D 39 dsens I VD power supply short sense input
40 FLPILM O Flap illumination output
41 ILMPW O Illumination output
42 ejtin I Eject key input
43 CDMUTE I CD mute
44 rds%&k I Not used
45 rdslk I Not used
46 RDT I Not used
47-56 NC Not used
57 EMUTE O EVol mute
58,59 NC Not used
60 VCC I Power supply input
E Not used
61 NC
62 VSS I GND
63-66 NC Not used
67 DALMON O Output for dark current reduction circuit
68 NC Not used
69 tunpce@ O TUNER : Chip enable output(EEPROM)
70 TUNPCE1 O TUNER : Chip enable output(PLL)

DEH-P580MP/XN/UC
64
1 2 3 4
 5 6 7 8

Pin No. Pin Name I/O Function and Operation

71 ROMCS O ROM correction : Chip select output
72 asens I ACC sense input
73 bsens I Back up sense input A
74 ROMCK O ROM correction : Clock output
75 ROMDATA I/O ROM correction : Data input/output
76 VST O EVOL : Strobe output
77 VDT O EVOL : Data output
78 VCK O EVOL : Clock output
79 IPPW O IP-BUS : Driver power supply control output
80 ASENBO O IP-BUS : Slave ACC sense output
81 isens I Illumination sense input
82,83 MODEL1,0 I Model select input 1,0
84 NC Not used
85 MUTE O System mute output
B
86 TESTIN I Test program input
87,88 NC Not used
89 KEYAD I Wired remote control : A/D input
90 LVLINR I Level indicator Rch input
91 CSENS I Flap opening-and-closing sense input
92 LVLINL I Level indicator Lch input
93 NC I Not used
94 AVSS I A/D converter GND input
95 SL I TUNER : Signal level input
96 VREF I A/D converter reference voltage
97 AVCC I A/D converter power supply input
98 TUNPDI I TUNER : Data input(PLL) C
99 TUNPDO O TUNER : Data output(PLL)
100 TUNPCK O TUNER : Clock output(PLL)

* PEG146A
75

51

76 50

D
100 26
1

25

DEH-P580MP/XN/UC
5 6 7 8
65
 1 2 3 4

- FM/AM Tuner Unit

7 6 13 5 10 9 8 11 14 18 19 20 21

CE2

ROM_VDD

SL

DI
CK
CE1

DO
NC

NC

NC

NC

NC
NC
A

IC 3 EEPROM IC 5
←
5.0V 5V 3.3V

OSC LPF

AM ANT FMRF
1 ATT
Rch
24
IC 2
IC 1 2.5V
FM ANT
3 3.3V
ATT Lch
23
FMRF MIXER, IF AMP DET, FM MPX
B
RF adj
ANT adj

T51 CF52
AUDIOGND

IC 4
OSCGND

VDD_3.3

←
RFGND

3.3V 3.3V 2.5V 2.5V

DGND

VCC
NC

2 12 15 22 16 4 17

No. Symbol I/O Explain

C 1 AMANT I AM antenna input AM antenna input high impedance AMANT pin is connected with
an all antenna by way of 4.7µH. (LAU type inductor) A series circuit
including an inductor and a resistor is connected with RF ground for
the countermeasure against the hum of power transmission line.
2 RFGND RF ground Ground of antenna block
3 FMANT IFM antenna input Input of FM antenna 75Ω Surge absorber(DSP-201M-S00B) is necessary.
4 VCC power supply The power supply for analog block. D.C 8.4V ± 0.3V
5 SL O signal level Output of FM/AM signals level
6 CE2 I chip enable-2 Chip enable for EEPROM ”Low” active
7 NC non connection Not used
8 CE1 I chip enable-1 Chip enable for AF•RF ”High” active
D 9 CK I clock Clock
10 DI I data in Data input
11 NC non connection Not used
12 OSCGND osc ground Ground of oscillator block
13 ROM_VDD power supply Power supply for EEPROM pin 13 is connected with a power supply of
micro computer.
14 DO O data out Data output
15 DGND digital ground Ground of digital block
16 NC non connection Not used
17 VDD_3.3 power supply The power supply for digital block. 3.3V ± 0.2V
18 NC non connection Not used
19 NC non connection Not used
E 20 NC non connection Not used
21 NC non connection Not used
22 AUDIOGND audio ground Ground of audio block
23 L ch O L channel output FM stereo “L-ch” signal output or AM audio output
24 R ch O R channel output FM stereo “R-ch” signal output or AM audio output

DEH-P580MP/XN/UC
66
1 2 3 4
 5 6 7 8

7.3 OPERATIONAL FLOW CHART

Power ON
A

VCC = 5 V
Pin 14

bsens
Pin 73

bsens = L
B

asens
Pin 72

asens = L

dsens
Pin 39

dsens = L

ASENBO←H C
Pin 80

CSENS
- 2 V < CSENS < 3 V
Pin 91
Last source returns.
2 V < CSENS < 3 V CD loading functions are available.
Keys except for EJECT key are not available.
Starts
communication
with Grille
microcomputer. 300 ms D

SWVDD←H
Pin 38 300 ms
In case of the above signal, the communication
Source keys with Grille microcomputer may fail.
operative If the time interval is not 300 msec, the oscillator
may be defective.

E
Source ON

SYSPW←H
Pin 1

Completes power-on operation.

(After that, proceed to each source operation)
F

DEH-P580MP/XN/UC
5 6 7 8
67
 1 2 3 4

8. OPERATIONS

DEH-P580MP/XN/UC
68
1 2 3 4
5 6 7 8

DEH-P580MP/XN/UC
5 6 7 8
69
 1 2 3 4

Fixing the Front Panel

If you do not operate the removing and attaching the front panel function, use the supplied fixing screws and
holders to fix the front panel to this unit.
A
1. Attach the holders to both sides of the front panel.
Holder(CND1250)

Holder(CND1249)

2. Replace the front panel to the unit.

B

3. Flip the holders into upright positions.

C

4. Fix the front panel to the unit using fixing screws.

Fixing screw(BPZ20P060FTB)
D

Fixing screw(BPZ20P060FTB)

DEH-P580MP/XN/UC
70
1 2 3 4
5 6 7 8

DEH-P580MP/XN/UC
5 6 7 8
71
 1 2 3 4

- Jigs List
Name Jig No. Remarks
A Test Disc TCD-782 Checking
g the g
grating
g
L.P.F. Checking
g the g
grating
g ((Two pieces))

- Grease List
Name Grease No. Remarks
Grease GEM1024 CD Mechanism Module
B Grease GEM1045 CD Mechanism Module

Before shipping out the product, be sure to clean the

following portions by using the prescribed cleaning
tools:
C
Portions to be cleaned Cleaning
g tools
CD pickup lenses Cleaning liquid : GEM1004
Cleaning
g paper
p p : GED-008

DEH-P580MP/XN/UC
72
1 2 3 4