N:\SolidWorks\Issue\cp2589-120.

slddrw
Last Saved: darrowsmith on 11 December 2007 09:14:16
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

IF IN IF THIS DOCUMENT IS PRINTED IN HARDCOPY, THIS DRAWING IS CONFIDENTIAL AND IS SUPPLIED ON THE EXPRESS
MANUFACTURING DRAWING AP Racing
M
A1 PART NUMBER(S) / DRAWING NUMBER

CP2589-120
DRAWN TO B.S. 8888
THREADS TO B.S.3643 PT2
DO NOT
SCALE
DOUBT
ASK
FIRST ANGLE
PROJECTION
IT IS FOR INFORMATION ONLY AND THEREFORE
IS NOT SUBJECT TO UPDATING CONTROLS.
ALWAYS REFER TO VIEWER FOR LATEST ISSUE.
CONDITION THAT IT SHALL NOT BE LOANED OR COPIED OR DISCLOSED
TO ANY OTHER PERSON OR USED FOR ANY OTHER PURPOSE WITHOUT
THE WRITTEN CONSENT OF AP RACING LTD.
Wheler Road
Coventry
CV3 4LB
M

THIS DISC HAS BEEN SPECIFICALLY DESIGNED TO BE Tel: +44 (0) 24 7663 9595
Fax: +44 (0) 24 7663 9559
STEP OUT
0.20 TWIN TURNED, AND MUST NOT BE MANUFACTURED © AP Racing Ltd. 2006
http://www.apracing.com

254.00 0.00 BY ANY OTHER METHOD.

INITIALS
ZONE
ISSUE HISTORY
L L
No. DATE &
PCO No. PARTICULARS
4 10/02/2004 RE-DRAWN ON SW. # GM
B2154 CASTING COURCE CP2589-106C
WAS CP2589-101C
R0.80 48.60 5 12/11/07 DISC CONVERTED TO TWIN DRA
48.50 B4460:ID82 TURNING, NOTE ADDED. L11
45. MIS0380 NOTE ADDED. J13
00 ° 0.20/0.00 STEP & R0.80 ADDED. L8
Ø168.20 ADDED. G9
K 20.75 PART MARKING NOTE ADDED. D8 K
GENERAL NOTES ADDED.
20.65 CASTING WAS -106C
74.00 74.00
6 04/12/2007 DIM 141.50 TO INTERSECTION # GM
RAC21624 REMOVED
DETAIL D = =
SCALE 10 : 1 7 06/12/07 139.00 REF TO INT'N ADDED F8 GM
RAC21624 6.00 REMOVED: INT'N TO CASTG11
8.20 FACE
254.00 WAS 254.00/253.85 L5

J
8 11/12/07 DATUM A ADDED. MAX MATL. H13 DRA
J
RAC21629 CONDITION ADDED TO HOLE C6
POSN TOLERANCE
B
MACHINE MIN. OFF
CASTING TO CLEAN UP FOR FLATNESS, PARALLELISM
ONLY. & SURFACE FINISH LIMITS
REFER TO MIS0380

D
H H
A

3.00
R1.50
C C

°
139.00 REF TO INTERSECTION
G G

168.20

121.38
121.30

170.00
62.00
F
F

3.00° CAST

E E
R3.00

'V' GROOVES PER FACE 5.00x45

EQUISPACED AS SHOWN. DISC PART NUMBER TO BE ETCHED
GROOVES TO START AT R88.0 ON O/D AFTER M/C BALANCING R3.00
AND RUN-OUT AT R124.0 ACCORDING TO MIS0086 IN
DO NOT END MILL. LETTERS 2.5mm HIGH.
D D

UNLESS OTHERWISE STATED: MASS (grams)

DIMENSIONS IN MILLIMETRES.
REMOVE ALL BURRS. 4149.82
DIMENSION ARE BEFORE TREATMENT. VOLUME (mm³)

B 14.70 CHMF 0.5x45 DIMENSIONAL TOLERANCE

ANGULAR TOLERANCE
= 0.25 592831.64
4 HOLES THRU = 0 30' SCALE
14.60 B-B MAX SURFACE FINISH:

EQUI-SPACED ON A 100.00 PCD BY ANY METHOD =

ON MACHINED SURFACES = 3.2
µm (Ra)
µm (Ra)
1:1
CHF. 0.5 x 45 BOTH SIDES GENERAL MATERIAL DESCRIPTION
C
0.05 M A CAST IRON C
MATERIAL SPECIFICATION(S)
APRM0001
ALT MATERIAL SPECIFICATION(S) or ADDITIONAL MATERIAL NOTES
1.60
1.40

SURFACE TREATMENT / HEAT TREATMENT

NOTE:- 3.00 REFER TO MIS0075

TO BE MADE FROM CP2789-105C. R1.50
MADE FROM

B CP2589-105C B
UNLESS OTHERWISE STATED REMOVE ALL SHARP CORNERS 0.3 X 45 . DRAWN Gael Mace APPROVED

DERIVED FROM SHEETS

CASTING TO BE CLEAN, CLOSE GRAINED AND FREE FROM BLOW HOLES 1 OF 1
DRAWING TITLE
AND HARD SPOTS. SURFACE OF DISC TO BE FREE FROM POROSITY,
FLANGE M/C'ING TO BE SMOOTH WITH NO RIDGES OR GROOVES. SUFFIX DETAILS Ø254 x 20.7 TOP HAT
C-C VENTILATED DISC
P PLAIN, NO GROOVES PART NUMBER(S) / DRAWING NUMBER
DIP IN DE-WATERING OIL AFTER FINAL OP.
A
G (VALUE 'V')
GROOVES ONLY, VALUE 'V' PER FACE CP2589-120 A

DISC TO BE BALANCED AS SPECIFIED ON MIS0559

e.g. G8 GROOVES 8 PER FACE DRAWING FILE NAME
cp2589-120
DRAWING ISSUE
8
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16