SLOVENSKI STANDARD

SIST EN 10216-1:2014
01-junij-2014

1DGRPHãþD
SIST EN 10216-1:2003
SIST EN 10216-1:2003/A1:2004

1HYDUMHQHMHNOHQHFHYL]DWODþQHSRVRGH7HKQLþQLGREDYQLSRJRMLGHO
1HOHJLUDQHMHNOHQHFHYLVVSHFLILFLUDQLPLODVWQRVWPL]DGHORSULVREQLWHPSHUDWXUL

Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 1: Non
-alloy steel tubes with specified room temperature properties
iTeh STANDARD PREVIEW
Nahtlose Stahlrohre für Druckbeanspruchungen - Technische Lieferbedingungen - Teil 1:
(standards.iteh.ai)
Rohre aus unlegierten Stählen mit festgelegten Eigenschaften bei Raumtemperature
SIST EN 10216-1:2014
https://standards.iteh.ai/catalog/standards/sist/46e0f653-135c-42c1-aa21-
Tubes sans soudure en acier pour service sous pression - Conditions techniques de
5a605638df5c/sist-en-10216-1-2014
livraison - Partie 1 : Tubes en acier non allié avec caractéristiques spécifiées à
température ambiante

Ta slovenski standard je istoveten z: EN 10216-1:2013

ICS:
23.020.30 7ODþQHSRVRGHSOLQVNH Pressure vessels, gas
MHNOHQNH cylinders
77.140.75 Jeklene cevi in cevni profili Steel pipes and tubes for
za posebne namene specific use

SIST EN 10216-1:2014 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
 SIST EN 10216-1:2014

iTeh STANDARD PREVIEW

(standards.iteh.ai)
SIST EN 10216-1:2014
https://standards.iteh.ai/catalog/standards/sist/46e0f653-135c-42c1-aa21-
5a605638df5c/sist-en-10216-1-2014
 SIST EN 10216-1:2014

EUROPEAN STANDARD EN 10216-1

NORME EUROPÉENNE
EUROPÄISCHE NORM December 2013

ICS 23.040.10; 77.140.75 Supersedes EN 10216-1:2002

English Version

Seamless steel tubes for pressure purposes - Technical delivery

conditions - Part 1: Non-alloy steel tubes with specified room
temperature properties

Tubes sans soudure en acier pour service sous pression - Nahtlose Stahlrohre für Druckbeanspruchungen -
Conditions techniques de livraison - Partie 1 : Tubes en Technische Lieferbedingungen - Teil 1: Rohre aus
acier non allié avec caractéristiques spécifiées à unlegierten Stählen mit festgelegten Eigenschaften bei
température ambiante Raumtemperatur

This European Standard was approved by CEN on 17 August 2013.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
iTeh STANDARD PREVIEW
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
(standards.iteh.ai)
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies ofSISTAustria,

ENBelgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
10216-1:2014
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
https://standards.iteh.ai/catalog/standards/sist/46e0f653-135c-42c1-aa21-
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom. 5a605638df5c/sist-en-10216-1-2014

EUROPEAN COMMITTEE FOR STANDARDIZATION

COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels

© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 10216-1:2013 E
worldwide for CEN national Members.
 SIST EN 10216-1:2014

EN 10216-1:2013 (E)

Contents Page

Foreword ...................................................................................................................................................................... 4
1 Scope .............................................................................................................................................................. 5
2 Normative references .................................................................................................................................... 5
3 Terms and definitions ................................................................................................................................... 6
4 Symbols .......................................................................................................................................................... 6
5 Classification and designation ..................................................................................................................... 6
5.1 Classification.................................................................................................................................................. 6
5.2 Designation .................................................................................................................................................... 6
6 Information to be supplied by the purchaser ............................................................................................. 7
6.1 Mandatory information .................................................................................................................................. 7
6.2 Options ........................................................................................................................................................... 7
6.3 Example of an order ...................................................................................................................................... 8
7 Manufacturing process ................................................................................................................................. 8
7.1 Steelmaking process ..................................................................................................................................... 8
7.2 Tube manufacture and delivery conditions ................................................................................................ 8
8
8.1
iTeh STANDARD PREVIEW
Requirements ................................................................................................................................................. 9
General ............................................................................................................................................................ 9
8.2
8.2.1
(standards.iteh.ai)
Chemical composition .................................................................................................................................. 9
Cast analysis .................................................................................................................................................. 9
8.2.2 Product analysis ..........................................................................................................................................
SIST EN 10216-1:2014 11
8.3 Mechanical properties .................................................................................................................................
https://standards.iteh.ai/catalog/standards/sist/46e0f653-135c-42c1-aa21- 12
8.3.1 Mechanical properties for quality TR2....................................................................................................... 12
5a605638df5c/sist-en-10216-1-2014
8.3.2 Mechanical properties for quality TR1....................................................................................................... 12
8.4 Appearance and internal soundness ......................................................................................................... 13
8.4.1 Appearance .................................................................................................................................................. 13
8.4.2 Internal soundness ...................................................................................................................................... 13
8.5 Straightness ................................................................................................................................................. 14
8.6 Preparation of ends ..................................................................................................................................... 14
8.7 Dimensions, masses and tolerances ......................................................................................................... 14
8.7.1 Diameter and wall thickness ....................................................................................................................... 14
8.7.2 Mass .............................................................................................................................................................. 14
8.7.3 Lengths ......................................................................................................................................................... 14
8.7.4 Tolerances .................................................................................................................................................... 17
9 Inspection ..................................................................................................................................................... 17
9.1 Types of inspection ..................................................................................................................................... 17
9.2 Inspection documents ................................................................................................................................. 18
9.2.1 Types of inspection documents ................................................................................................................. 18
9.2.2 Content of inspection documents .............................................................................................................. 18
9.3 Summary of inspection and verification testing ...................................................................................... 19
10 Sampling ....................................................................................................................................................... 20
10.1 Frequency of tests ....................................................................................................................................... 20
10.1.1 Test unit ........................................................................................................................................................ 20
10.1.2 Number of sample tubes per test unit ....................................................................................................... 20
10.2 Preparation of samples and test pieces .................................................................................................... 20
10.2.1 Selection and preparation of samples for product analysis .................................................................. 20
10.2.2 Location, orientation and preparation of samples and test pieces for mechanical tests .................... 20
11 Verification test methods ............................................................................................................................ 21

2
 SIST EN 10216-1:2014

EN 10216-1:2013 (E)

11.1 Chemical analysis ............................................................................................................................... 21

11.2 Tensile test ........................................................................................................................................... 22
11.3 Impact test ............................................................................................................................................ 22
11.4 Leak tightness test .............................................................................................................................. 23
11.4.1 Hydrostatic test ................................................................................................................................... 23
11.4.2 Electromagnetic test ........................................................................................................................... 23
11.5 Dimensional inspection ...................................................................................................................... 23
11.6 Visual examination .............................................................................................................................. 23
11.7 Non-Destructive Testing ..................................................................................................................... 23
11.8 Retest, sorting and reprocessing ...................................................................................................... 24
12 Marking ................................................................................................................................................. 24
12.1 Marking to be applied.......................................................................................................................... 24
12.2 Additional marking .............................................................................................................................. 24
13 Protection ............................................................................................................................................. 24
Annex A (informative) Technical changes from the previous edition ......................................................... 25
A.1 Introduction .......................................................................................................................................... 25
A.2 Technical changes .............................................................................................................................. 25
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 97/23/EC ............................................................................................ 26
Bibliography ...................................................................................................................................................... 27

iTeh STANDARD PREVIEW

(standards.iteh.ai)
SIST EN 10216-1:2014
https://standards.iteh.ai/catalog/standards/sist/46e0f653-135c-42c1-aa21-
5a605638df5c/sist-en-10216-1-2014

3
 SIST EN 10216-1:2014

EN 10216-1:2013 (E)

Foreword
This document (EN 10216-1:2013) has been prepared by Technical Committee ECISS/TC 110 “Steel tubes
and fittings for steel tubes”, the secretariat of which is held by UNI.

This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2014, and conflicting national standards shall be withdrawn at
the latest by June 2014.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.

This document supersedes EN 10216-1:2002.

For the list of the most significant technical changes that have been made in this new edition, see Annex A.

This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).

For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
iTeh STANDARD PREVIEW
This European Standard consists of the following parts, under the general title "Seamless steel tubes for
pressure purposes  Technical delivery conditions":
(standards.iteh.ai)
 Part 1: Non-alloy steel tubes with specified room temperature properties;
SIST EN 10216-1:2014
https://standards.iteh.ai/catalog/standards/sist/46e0f653-135c-42c1-aa21-
 Part 2: Non-alloy and alloy steels tubes with specified elevated temperature properties;
5a605638df5c/sist-en-10216-1-2014
 Part 3: Alloy fine grain steel tubes;

 Part 4: Non-alloy and alloy steel tubes with specified low temperature properties;

 Part 5: Stainless steel tubes.

Another European Standard series covering tubes for pressure purposes is:

 EN 10217, Welded steel tubes for pressure purposes  Technical delivery conditions.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

4
 SIST EN 10216-1:2014

EN 10216-1:2013 (E)

1 Scope
This European Standard specifies the technical delivery conditions for two qualities TR1 and TR2 of seamless
tubes of circular cross section with specified room temperature properties made of non-alloy quality steel.

NOTE Once this standard is published in the Official Journal of the European Union (OJEU) under
Directive 97/23/EC, presumption of conformity to the Essential Safety Requirements (ESR) of Directive 97/23/EC is limited
to technical data of materials in this standard and does not presume adequacy of the material to a specific item of
equipment. Consequently, the assessment of the technical data stated in this material standard against the design
requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied,
needs to be done by the designer or manufacturer of the pressure equipment, taking also into account the subsequent
manufacturing processes which may affect properties of the base materials.

2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.

EN 10020, Definition and classification of grades of steel

EN 10021, General technical delivery conditions for steel products

iTeh STANDARD PREVIEW

EN 10027-1, Designation systems for steels  Part 1: Steel names

EN 10027-2, Designation systems(standards.iteh.ai)

for steels  Part 2: Numerical system

EN 10052, Vocabulary of heat treatment terms for10216-1:2014

SIST EN ferrous products
https://standards.iteh.ai/catalog/standards/sist/46e0f653-135c-42c1-aa21-
EN 10168, Steel products  Inspection documents  List of information and description
5a605638df5c/sist-en-10216-1-2014
EN 10204, Metallic products  Types of inspection documents

EN 10220, Seamless and welded steel tubes  Dimensions and masses per unit length

CEN/TR 10261, Iron and steel  European standards for the determination of chemical composition

EN 10266, Steel tubes, fittings and structural hollow sections  Symbols and definitions of terms for use in
product standards

EN ISO 148-1, Metallic materials  Charpy pendulum impact test  Part 1: Test method (ISO 148-1)

EN ISO 377, Steel and steel products  Location and preparation of samples and test pieces for mechanical
testing (ISO 377)

EN ISO 2566-1, Steel  Conversion of elongation values  Part 1: Carbon and low alloy steels
(ISO 2566-1)

EN ISO 6892-1, Metallic materials  Tensile testing  Part 1: Method of test at room temperature
(ISO 6892-1)

EN ISO 10893-1, Non-destructive testing of steel tubes  Part 1: Automated electromagnetic testing of
seamless and welded (except submerged arc-welded) steel tubes for the verification of hydraulic leaktightness
(ISO 10893-1)

5
 SIST EN 10216-1:2014

EN 10216-1:2013 (E)

EN ISO 10893-2, Non-destructive testing of steel tubes  Part 2: Automated eddy current testing of seamless
and welded (except submerged arc-welded) steel tubes for the detection of imperfections (ISO 10893-2)

EN ISO 10893-3, Non-destructive testing of steel tubes  Part 3: Automated full peripheral flux leakage
testing of seamless and welded (except submerged arc-welded) ferromagnetic steel tubes for the detection of
longitudinal and/or transverse imperfections (ISO 10893-3)

EN ISO 10893-10, Non-destructive testing of steel tubes  Part 10: Automated full peripheral ultrasonic
testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of longitudinal
and/or transverse imperfections (ISO 10893-10)

EN ISO 14284, Steel and iron  Sampling and preparation of samples for the determination of chemical
composition (ISO 14284)

ISO 11484, Steel products  Employer's qualification system for non-destructive testing (NDT) personnel

3 Terms and definitions

For the purposes of this document, the terms and definitions given in EN 10020, EN 10021, EN 10052,
EN 10266 and the following apply.

3.1
employer
organization for which a person works on a regular basis
iTeh STANDARD PREVIEW
Note 1 to entry: The employer may be either the tube manufacturer or a third party organization providing non-
destructive testing (NDT) services. (standards.iteh.ai)
SIST EN 10216-1:2014
4 Symbols https://standards.iteh.ai/catalog/standards/sist/46e0f653-135c-42c1-aa21-
5a605638df5c/sist-en-10216-1-2014
For the purpose of this Part of EN 10216, the symbols given in EN 10266 apply.

5 Classification and designation

5.1 Classification

According to the classification system in EN 10020, the steels are classified as non-alloy quality steels.

5.2 Designation

5.2.1 For the tubes covered by this Part of EN 10216 the steel designation consists of:

 the number of this Part of EN 10216;

plus either:

 the steel name in accordance with EN 10027-1;

or:

 the steel number allocated in accordance with EN 10027-2.

6
 SIST EN 10216-1:2014

EN 10216-1:2013 (E)

5.2.2 The steel name is designated by:

 the capital letter P for pressure purposes;

 the indication of the specified minimum yield strength for thickness ≤ 16 mm, expressed in MPa
(see Table 5 and Table 6);

plus either:

 the alphanumeric TR1 for qualities without specified aluminium content, impact properties and specific
inspection and testing requirements (see 9.1);

or:

 the alphanumeric TR2 for qualities with specified aluminium content, impact properties and specific
inspection and testing requirements.

6 Information to be supplied by the purchaser

6.1 Mandatory information

The following information shall be supplied by the purchaser at the time of enquiry and order:

 iTeh STANDARD PREVIEW

the quantity (mass or total length or number);

 the term “tube”; (standards.iteh.ai)

 the dimensions (outside diameter D and
SISTwall thickness T) (see Table 7);
EN 10216-1:2014
https://standards.iteh.ai/catalog/standards/sist/46e0f653-135c-42c1-aa21-
 the designation of the steel grade in accordance with this Part of EN 10216 (see 5.2).
5a605638df5c/sist-en-10216-1-2014

6.2 Options

A number of options are specified in this Part of EN 10216 and these are listed below. In the event that the
purchaser does not indicate a wish to implement any of these options at the time of enquiry and order, the
tubes shall be supplied in accordance with the basic specification (see 6.1).

1) Delivery condition normalized or normalizing-formed for TR1 (see 7.2.2);

2) restriction on copper and tin contents (see Table 2 and Table 3);

3) product analysis (see 8.2.2);

4) verification of longitudinal impact testing at −10 °C for quality TR2 (see Table 5 and Table 6);

5) selection of method for verification of leak-tightness (see 8.4.2.1);

6) Non-Destructive Testing for quality TR2 (see 8.4.2.2); the test method shall be specified by the
purchaser;

7) special end preparation (see 8.6);

8) exact lengths (see 8.7.3);

9) inspection document 3.2 other than the standard document (see 9.2.1);

7
 SIST EN 10216-1:2014

EN 10216-1:2013 (E)

10) test unit restriction for tubes with D ≤ 76,1 mm of quality TR2 (see 10.1.1);

11) wall thickness measurement away from the ends (see 11.5);

12) additional marking (see 12.2);

13) protection (see 13).

6.3 Example of an order

100 t of seamless tube with an outside diameter of 168.3 mm, a wall thickness of 4,5 mm, in accordance with
EN 10216-1, made of steel grade P235TR2 with a 3.2 inspection certificate in accordance with EN 10204.

EXAMPLE 100 t - Tube – 168,3 × 4,5 - EN 10216-1 - P235TR2 - 3.2.

7 Manufacturing process

7.1 Steelmaking process

The steelmaking process is at the discretion of the manufacturer with the exception that the open hearth
(Siemens-Martin) process shall not be employed unless in combination with a secondary steelmaking or ladle
refining process.

Steels shall be fully killed.

iTeh STANDARD PREVIEW
NOTE This excludes the use of rimming, balanced or semi-killed steel.
(standards.iteh.ai)
7.2 Tube manufacture and delivery conditions
SIST EN 10216-1:2014
https://standards.iteh.ai/catalog/standards/sist/46e0f653-135c-42c1-aa21-
7.2.1 All NDT activities shall be carried out by qualified and competent level 1,2 and/or 3 personnel
authorized to operate by the employer. 5a605638df5c/sist-en-10216-1-2014

The qualification shall be in accordance with ISO 11484 or, at least, an equivalent to it.

It is recommended that the level 3 personnel be certified in accordance with EN ISO 9712 or, at least, an
equivalent to it.

The operating authorization issued by the employer shall be in accordance with a written procedure.

NDT operations shall be authorized by level 3 NDT individual approved by the employer.

NOTE The definition of level 1, 2 and 3 can be found in appropriate standards, e.g. EN ISO 9712 and ISO 11484.

7.2.2 The tubes shall be manufactured by a seamless process. The forming operations and delivery
conditions are shown in Table 1.

Table 1 — Forming operations and delivery conditions

Forming operation Quality Delivery condition

As formed or normalized or
TR1 a
normalizing-formed
Hot formed
TR2 Normalized or normalizing-formed

Hot formed + cold finished TR1 and TR2 Normalized

a
At the discretion of the manufacturer unless option 1 is specified.

8
 SIST EN 10216-1:2014

EN 10216-1:2013 (E)

Option 1 : The tube shall be supplied in normalized or normalizing-formed delivery condition.

8 Requirements

8.1 General

When supplied in a delivery condition indicated in 7.2 and inspected in accordance with Clauses 9, 10 and 11,
the tubes shall conform to the requirements of this Part of EN 10216.

In addition, the general technical delivery requirements specified in EN 10021 shall apply.

8.2 Chemical composition

8.2.1 Cast analysis

The cast analysis reported by the steel producer shall apply and conform to the requirements of Table 2 for
quality TR2 and in Table 3 for quality TR1.

When welding tubes are produced in accordance with this Part of EN 10216, account should be taken of the
fact that the behaviour of the steel during and after welding is dependent not only on the steel, but also on the
applied heat treatment and the conditions of preparing for and carrying out the welding.

a
Table 2 — Chemical composition (cast analysis) in % by mass for quality TR2
iTeh STANDARD PREVIEW
Steel grade
C Si Mn (standards.iteh.ai)
P S Cr
b
Mo
b
Ni
b
Al tot Cu
bc
Nb
b
Ti
b
V
b
Cr+Cu+Mo+Ni
b

Steel Steel max. max. max. max. max. max. ENmax. max. min. max. max. max. max. max.
name number SIST 10216-1:2014
https://standards.iteh.ai/catalog/standards/sist/46e0f653-135c-42c1-aa21-
d
P195TR2 1.0108 0,13 0,35 0,70 0,025 0,015 5a605638df5c/sist-en-10216-1-2014
0,30 0,08 0,30 0,02 0,30 0,010 0,04 0,02 0,70

d
P235TR2 1.0255 0,16 0,35 1,20 0,025 0,015 0,30 0,08 0,30 0,02 0,30 0,010 0,04 0,02 0,70

d
P265TR2 1.0259 0,20 0,40 1,40 0,025 0,015 0,30 0,08 0,30 0,02 0,30 0,010 0,04 0,02 0,70

a
Elements not included in this table shall not be intentionally added to the steel without the agreement of the purchaser, except for elements which
may be added for finishing the cast. All appropriate measures shall be taken to prevent the addition of undesirable elements from scrap or other
materials used in the steelmaking process.
b
The content of these elements need not be reported unless intentionally added to the cast.
c
Option 2:In order to facilitate subsequent forming operation, an agreed maximum copper content lower than indicated and an agreed specified
maximum tin content shall apply.
d
This requirement is not applicable provided the steel contains a sufficient amount of other nitrogen binding elements which shall be reported.