BASIC TECHNOLOGY EXAM QUESTIONS

FOR JSS2 THIRD TERM

 6 minutes read

JSS2 THIRD TERM BASIC TECHNOLOGY

EXAMINATION QUESTIONS –
EDUDELIGHT.COM

Examination malpractices may lead to a repeat of the subject or suspensions

don’t be involved.

CLASS: J.S.S 2

SUBJECT: BASIC TECH

1. Engineers should be good at ____________ a. Literature b. sport

c.mathematics d. accounting

2. __________produce conceptual models of building which are translated

to a set of architectural drawings a.lawyerb.athletesc.artisted.architect

3. The process of splitting the log into marketable sizes is known as a.

seasoning b.fellingc.preservativesd.conversion

4. A/an______ is any feature that reduce the quality value of timber

a.defectb.effect c.veneer d.board

5. A steel is a mixture of iron and_________ a.carbon b. copper c.zincd.tin

6. Metals can be obtained from rocks these rocks are known as_________
a.moltenb.drill c. ore d. base

7. Ceramics are product made from _________ and dried to

hardness.a.glass b.clay c.metals d. wood
8. A cube has _______ faces a.8 b.12 c.6 d.10

9. A form of pictoral drawing which is inclined at 300 to the horizontal

plane is called a.obliqueb.isometricc.perpendicular d. orthographic

10. The process of heating and melting ore Is called a.smeltingb.casting

c. alloy d. stage

11. There are ______ main methods of orthographic projection.

A.threeb.fourc.two d. six

12. _______ refers to glue or resin used for joints fitting a. fitting
b.adhesives c. nail d.sander

13. one of these is not a joint a.dovetailb.plain lap c. mortic and tenon d.
wood lathe

14. Angle on a straight line is ________ a.180 b. 360 b.45 c.90

15. Which of these polygons has four sides a. Triangle

b.quadrilateralc.pentagon d. octatgon

16. A polygon with 10 sides is known as (a) Decagon (b) Hexagon (c)
Octagon (d) Pentagon

17. A quadrilateral with opposite sides equal and opposite is known as (a)
Polygon (b) Parallelogram (c) Decagon (d) Hexagon

18. ____________ is an example of(a) Thin continuous (b) Thin long chain (c)
Thin wavy (d) Thin short

19. A line that divides a circle into two halves is known as(a) Chord (b)
Tangent (c) Radius (d) Diameter

20. __________ is a straight line drawn from the center of the circumference.
(a)Tangent (b) Radius (c) Chord (d) Tangle

21. Hardware examples includes the following except ____________

 (A)Monitor (B) mouse (C) operating system (D) keyboard

22 F.M Means_________________________________________________3 One

of these is 23. an example of analogue signal/device

(A) Computer system (B) human voice (C) dvd player (D) plasma tv

24 The demerits of the internet includes these except

____________________

Read Also

Primary Two Third INFORMATION

Term Examination TECHNOLOGY

Questions EXAM QUESTIONS

2019/2020 Session FOR JSS3 SECOND

– All Subject TERM

(A) Access to library (B) pornography (C) cybercrime (D) fraud

25 Ferrous metal are metal which contains _____________________

(A) Cupper (B) iron (C) carbon (D) silicon

26 The basic material for the production of ceramics is _________________

(A) Clay (B) humidity (C) resuscitation (D) temperature

27 A.M Means ______________________

28 Tyres is made from ______________________________________

(A) Ceramic (B) rubbers (C) metals (D) wood

29 G.S.M Stands for ___________________________________________________

___________________________________________

30 ____________is the degree of hotness or coldness of a body or place

(A) Pressure (B) humidity (C) resuscitation (D) temperature

31 The following are software except ___________________

(A)Cedar (B) pine (C) iroko (D) spruce

32 The letter “S” in S.I.M Stand for _____________________

(A) Server (B) subscriber (C) system (D) source

33 Bronze is an alloy of ______________ and copper

(A) Tin (B) zine (C) sliver (D) aluminum

34 Ceramics have been used for ages in ________________

(A) Law (B) medicine (C) sculpture (D) politics

35 Gentian violet is _________________ in colour

(A) Red (B) yellow (C) white (D) purple

THEORY

Attempt all questions

1a Define the term

(i) Analog signal (ii) digital signal

1b in tabular form, state five differences between analog and digital

signal

1c Draw the analog and d digital signal

2a Define the terms

(i) First aid (ii) first aid box

2b List ten items that can be found in the first aid box

2c who is a first aider

3a what is an alloy?

3b Give five examples of alloy

3c Distinguish between nature and synthetic rubbers.

c. What are search engines used for?

2. Who is a computer professional?

b. Name four categories of computer professional

c. State four qualities of a good computer professional

3a. Define the term ‘Digital divide’

B. State the effects of digital divide

BASIC TECHNOLOGY EXAM QUESTIONS FOR JSS2 THIRD TERM

Subject: BASIC TECHNOLOGY

Duration: 2HRS

Class: JSS 2

OBJECTIVE
 1. ___________ are basically four sided plane figure (a) Quadrilaterals (b)
Polygons (c) Board practice (d) Drawing boards

2. __________ all sides and angles are equal (a) Square (b) Rectangle (c)
Trapezium (d) Kite

3. __________ are plane figures bounded by more than four straight lines . (a)
Trapezium (b) Square (c) Polygons (d) Kite

4. Pentagon has _______ Sides (a) 6 (b) 5 (c) 8 (d) 10

5. Polygon with 8 sides is Called ________ (a) Heptagon (b) pentagon (c)
Octagon (d) Decagon

6. Polygon with Six Sides is Called _______ (a)Octagon (b) Hexagon (c)
Decagon (d) Heptagon

7. __________ is a Straight line which touches the circumference at a Point

(a) Tangent (b) Arcs (c) Rectangle (d) Square

8. ________ is a Plane figure bounded by three straight lines (a) Rectangle

(b) Triangle (c) Square (d) Trapezium

9. _________ is a triangle that has three equal sides and three angles (a)
Equilateral Triangle (b) Isosceles Triangle (c) Scalene Triangle (d) Right
angle Triangle

10. __________ Can be defined as an operation organized to free from danger

(a) First aid operation (b) Rescue operation (c) Responsive operation (d)
Caring operation

11. Which of the following cannot be regarded as a rescue operation (a)

Vehicle-extrication rescue operation (b) Surface water rescue operation
(c) Air – Sea rescue operation (d) First aiding

12. Workshop accident includes the following except (a) Fracture (b)
Bleeding (c) voltaging (d) Wound

13. ________ is a table on which wood workers perform his operation (a)
Workbench (b) Imperial board (c) Dove Tail table (d) Tenon Table

14. Mixture of Sand, gravel, cement with water is Called (a) Plastering (b)
rendering (c) Concrete (d) Plastics

15. ________ is the name of buildings that contains many rooms on two floors
(a) Duplex (b) Bungalow (c) hut (d) High – Rise

16. Angles can be measured using ____ (a) French Curve (b) Compass (c)
Protractor
17. The instrument used for drawing irregular curve is called (a) divider (b)
Compass (c) Scale Rule (d) French Curve

18. The following methods can prevent accident while working in the
workshop, except (a) always use the right tools for each job (b) Always
keeps to instructor (c) Avoid using worn out tools (d) Always do more
than two jobs at the same time

19. ________ are equipment used in order to achieve safety? (a) Safely
devices (b) Fire extinguishers (c) Fire alarm (d) Fire buckets

20. Metals can be classified into _______ (a) Six (b) Five (c) Four (d) two

21. Papers are manufactured from _______ ceramics (b) Ferrous (c) alloy (d)
wood

22. The major purpose of maintenance in engineering is to ________ (a) Keep

it in good working condition (b) Prevent from making loud noise (c) Stop
it from working too long (d)Enable it to last forever

23. Workshop accident includes the following except (a) Fracture (b)
Bleeding (c) Plastering (d) Wound

24. One of the following is not among the rescue safely measures (a) Face
cap (b) Safely boot (c) hand gloves (d) helmets

25. First – aid can be used to care for the following except (a) Accident (b)
Injury (c) Headache (d) Blood Donation

26. __________ is used for transferring measurement (a) Divider (b) punches
(c) Micrometer (d) Try square

27. _________ is drawn at the bottom right hand corner of the drawing paper
(a) Boarder lines (b) Title block (c) Lettering (d) Figures

28. _______ are poor conductors of heat and electricity (a) Plastics (b) Metal
(c) Copper wire (d) Conductors

29. ___________ Plastic can be softened into liquid form and remoulded (a)
Thermosetting (b) Electric Plastic (c) Ceramic (d) Synthetic rubber

30. Any material that allows free flow of electrons and electricity is Called
_________ (a) Insulator (b) Conductors (c) Ceramics (d) Synthetic

31. The brown material between electric poles and the electric wire is Called
(a) Insulators (ceramic) (b) Thermoplastic (c) Synthetic (d) Vulcanization

32. Glass belong to _________ family (a) Plastics (b) Synthetic rubber (c)
Thermo set Plastics (d) Ceramics.
 33. Which of the following can be used for drawing vertical and inclined lines
? (a) Protectors (b) Scale rule (c) Compass (d) Set square

34. Scale rules are used to produce (a) Reduced or enlarged sizes (b) Equal
and normal size of drawing (c) Enlarged sizes of drawing (d) A good
Linear drawing

35. Which of the procedures comes first in Constructing a building (a)

Excavation (b) concreting (c) Level (d) Site preparation

36. Which of the following is not a Quadilateral (a) Prism (b) Rhomboid (c)
Rhombus (d) Parallelogram

37. __________ are used to reduce wear and tear (a) Lubricant (b)
Vulcanization (c) Synthetic (d) Abrasives

38. Oil and Grease are used as_______ (a) Vulcanization (b) Lubricants (c)
Synthetics (d) abrasives

39. Polygon with (10) Ten sides is Called (a) Pentagon (b) Heptagon (c)
Nonagon (d) Decagon

40. We have types of technology (a) 5 (b) 4 (c) 3 (d) 2

JSS2 THIRD TERM BASIC TECHNOLOGY EXAMINATION QUESTIONS –

EDUDELIGHT.COM

THEORY: Answer only three Question

1a Define Polygon b Construct the following polygon

i Pentagon AB 50mm ii Hexagon AB 70mm iii Octagon AB

70mm

2a Define Friction b State two advantages and two disadvantages of

friction

c Differentiate between Lubrication and Lubricants

d Mention two Lubricant used in reducing friction

3a Explain five care and maintenance that must be given to wood work
machines
b Explain two function of lathe machine

4 Sketch five workshop hard tools and Explain their uses

5a Explain the uses of the following technical drawing instrument

i Tee Square

ii Protractor

iii Set Square

iv Compass

v Divider

b Sketch tee square and label the parts

JSS2 THIRD TERM BASIC TECHNOLOGY EXAMINATION QUESTIONS –

EDUDELIGHT.COM