ARMOUR HIGH HEATRESIST540 – ALUMINIUM SILVER
AIR DRYING FINISH COAT
SINGLE PACK - LOW BUILD - SOLVENT BORNE
REVISED DATE: 23/08/2023
PRODUCT CODE: 49-201
TECHNICAL DATA SHEET: 1/140419
DESCRIPTION Ready to Use, Low Build, Slow Drying, Single Pack based
on High Temperature Resistance Silicone Resin
PRINCIPAL High Temperature Resistance Finish for use in new & maintenance of Steel Surfaces
PROPERTIES on Industrial Mufflers, Chimneys, Furnaces/Ovens, Pipes, Boilers, Exhausts, Stills, etc
• For continuous Dry Heat Resistance up to 400C
• Full Properties develop only after baking & reaching operating temperatures
• Bake minimum 45 minutes at 250C to develop full properties
• Will provide temporary corrosion protection after air drying
• Good Weather Resistance & Handling without intermediate baking.
• High Opacity
FINISH Reflective Sheen to Satin
COLOUR ALUMINIUM SILVER
BASIC DATA
Specific Gravity @ 23°C ± 0.9
Solids by Volume ±9%
Viscosity @ 23°C ± 13.5 F4C / (10 Sec F4C)
Recommended Film Thickness 15 to 25µm DFT)
Theoretical Spread Rate 4.5 m² / litre @ 20µm DFT
Practical Spread Rate 50 to 70% less than theoretical depending on substrate & application conditions
Touch Dry @ 23C ± 8 Hours depending on Ambient Temperature
Temporary Handling & Transport ± 24 Hours depending on Ambient Temperature
Over Coating Interval ± 36 Hours depending on Ambient Temperature
Shelf Life (Cool, Dry & Shaded) Minimum 9 months, in Original Sealed Packing
Flash Point below 22°C
LIMITATION • Do not expose to Rain, Water or Dew after application
• Contamination can result in Poor Cure or Gel
• Excessive Film Thickness can cause Gassing
• Keep Sealed when not in Use
RECOMMENDED UNDERCOAT Not Recommended
SUBSTRATE CONDITIONS • Substrates should be Dry and Free of any Dirt, Dust or Oily Residues
• Substrate Temperature should be at least 3ºC above Dew Point
• Clean sufficiently by Sandblasting or with Sandpaper
INSTRUCTIONS FOR USE • Stir well before Use
• Ambient Temperature should preferably be above 6°C
• Adequate Ventilation to be maintained during application and curing
• Apply One or Two Coats according to required DFT
Page 1 of 2
ARMOUR HIGH HEATRESIST540 – ALUMINIUM SILVER
AIR DRYING FINISH COAT
SINGLE PACK - LOW BUILD - SOLVENT BORNE
REVISED DATE: 23/08/2023
PRODUCT CODE: 49-201
TECHNICAL DATA SHEET: 1/140419
AIRLESS SPRAY Suitable
Thinner Volume • Not Recommended
Nozzle Orifice • 0.007 to 0.013“
Nozzle Pressure • 80 to 100 bar (1,160 – 1,450 psi)
AIR SPRAY Preferred
Thinner Volume • Not Recommended
Nozzle Orifice • 0.8 to 1.0mm
Nozzle Pressure • 2 to 3 bar (29 – 43.5 psi)
BRUSH / ROLLER Suitable
Thinner Volume • Not Recommended
DIPPING Not Recommended
RECOMMENDED THINNERS • FDE Thinner for Cleaning
SAFETY PRECAUTIONS • Contains Flammable Materials
• Keep Away from Sparks and Open Flames
• Avoid Skin Contact by using Gloves, Face Mask & Cream
• Refer to the Material Safety Data Sheet (MSDS)
Consult Technical Department for any further Enquiry or Assistance
MARINDEC PAINTS (PTY) LIMITED
P.O. Box 634
ALBERTON 1450
South Africa
11 Fuchs Street, ALRODE 1451 / 21 Fuchs Street, Alrode 1451
Tel: +27 (11) 908 1056
Fax: +27 (11) 908 4828
E-mail:
[email protected] [email protected]Limitation of Liability
• Information provided on this technical data sheet is supplied in good faith and is based on tests and information we believe to be
accurate and is intended for guidance only.
• All recommendations or suggestions provided on use of Marindec Paints manufactured products, whether in technical
documentations, or in response to a specific enquiry, or otherwise is purely based on data and information which is according to our
best knowledge and experience.
• Product information provided is intended for users having requisite application knowledge and industrial skills.
• It is ultimately the user’s responsibility to determine suitability of product for its intended use.
• Marindec Paints have no control over the substrate quality or it’s condition and many other factors that can affect use and
application of products manufactured by Marindec Paints..
• Marindec Paints therefore, do not accept any direct or indirect liability arising from any loss, injury or damage resulting from use of
Marindec Paints manufactured products or use of any contents of this technical data sheet unless there is a written agreement
stating otherwise.
• Data and Information provided in this technical data sheet is subject to change without notice, which can arise out of Marindec
Paint’s on going regular and continuous product development programme.
• This technical data sheet replaces all previous issued.
• Any person using or referring to such technical data sheet must ensure that it is current.
Page 2 of 2
