DESIGN CALCULATION AND CHECKING

FOR EDOTCO MALAYSIA SDN. BHD.

SITE NAME : JINJANG UTARA

SITE ID : e.coMY002817WW
LATITUDE & LONGITUDE : 3.21639 & 101.6588

PROPOSED INSTALLATION OF 6M FLOOR MOUNTED BIPOD

BOOM FOR EDOTCO TELECOMMUNICATION FACILITIES FOR
EDOTCO MALAYSIA SDN. BHD.

CONTRACTOR CLIENT
 TABLE OF CONTENTS

DESIGN BRIEF 1
1.0 INTRODUCTION 2
2.0 STANDARD AND CODES OF PRACTICE 2
3.0 SITE INFORMATION 2
4.0 DESIGN CRITERIA 3
5.0 WIND LOADING 5
6.0 BOOM DEFLECTION CHECK 5
7.0 CONCLUSION 5
SECTOR 1 9
SECTOR 2 AND 3 23
ANALYSIS OF STRUCTURE 37
DRAWING 42
DESIGN BRIEF

Page 1
1.0 INTRODUCTION

This is the design and analysis calculation report for the proposed of 6m floor
mounted bipod boom.

2.0 STANDARD AND CODES OF PRACTICE

The following standard and codes of practices are adopted for the structural
analysis and design:

• BS6399, Part 2: 1997 (Loading for Building)

• BS5950, Part 1: 1990 (Structural Use of Steelwork in Building)

All steel members are galvanized to BS 729:1971 (Hot Dip Galvanized Casting
on Iron and Steel Articles).

3.0 SITE INFORMATION

Site Name Jinjang Utara

Site ID e.coMY002817WW
Region Central
Site Address 6242, Jalan Jinjang Aman 16, Jinjang Utara, 52000
Kuala Lumpur, Wilayah Persekutuan Kuala Lumpur
Height of Structure 6m
Latitude and 3.21639 & 101.6588
Longitude

Page 2
4.0 DESIGN CRITERIA

The following list of design criteria are adopted in the design.

i. Material Strength:
• The pipes are grade API 5L Grade B minimum with minimum yield
strength of 241 N/mm² or welded pipe comply to BS1387 with
minimum yield strength of 195 N/mm².
• All plates and steel angles are Grade S275 comply to BS EN
10025:1993 with minimum yield strength of 275 N/mm².
• Structural bolts and anchor bolts using HSL-3 (grade 8.8) of HILTI.
• Concrete strength using standard 25Mpa comply to BS1881-
116;1983.

ii. Factor of Safety:

Combination Safety Factor

Combination 1 (Service Load) 1.0DL +1.0LL+1.0WL

Combination 2 (Max Load) 1.2DL+ 1.6LL

Combination 3 (Wind Load) 1.2DL +1.2LL+1.2WL

iii. Design Parameters

a) Design Wind Speed
The basic wind speed used in the design is 22.0 m/s which is mean
hourly wind speed specified in BS8100.

iv. Loadings

The 6.0m floor mounted bipod boom is analyzed to a specific loading

configuration below:

Page 3
 Antenna
Loading for
Boom Type 1: Size Quantity Height Weight Total
Sector 1 (mm) Mounted (m) (kg) Weight
Equipment (kN)
Antenna 1 0.445 x 1 6 36.2 0.355
0.13
Antenna 2 0.408 x 1 6 30.0 0.2964
0.199
RRU 0.342 x 1 6 26.3 0.25791
0.189

Antenna
Loading for
Boom Type 2: Size Quantity Height Weight Total
Sector 2 & 3 (mm) Mounted (m) (kg) Weight
Equipment (kN)
Antenna 1 0.445 x 1 6 36.2 0.355
0.13
Antenna 2 0.408 x 1 6 30.0 0.2964
0.199
RRU 0.342 x 1 6 26.3 0.25791
0.189

Page 4
5.0 WIND LOADING

STRUCTURE TOTAL WIND CAPACITY (KN)

Boom Type 1 (Sector 1) 0.12
Boom Type 2 (Sector 2 and 3) 0.12

6.0 BOOM DEFLECTION CHECK

• Type 1 (Sector 1): 6m floor mounted bipod boom

Result from STAAD PRO V8i, the deflection at top of the boom is 21.545mm,
thus;

δ = tan-1(21.545/6000)

= 0.2° ˂ allowable deflection of 0.5°

• Type 2 (Sector 2 & 3): 6m floor mounted bipod boom

Result from STAAD PRO V8i, the deflection at top of the boom is 21.365mm,
thus;

δ = tan-1(21.365/6000)

= 0.2° ˂ allowable deflection of 0.5°

7.0 CONCLUSION

From design generated by STAAD PRO V8i, we can conclude that the boom is
safe and adequate to carry the intended loading.

Page 5
WIND CALCULATION

Page 6
8.0 WIND LOAD CALCULATIONS
WIND CALCULATIONS

1.0 Wind Speed

a. Basic Wind Speed, Vb

Basic wind speed Vb = 22.22 m/s

b. Site Wind Speed, Vs

Site wind speed Vs = VbxSaxSdxSsxSp

Altitude Factor Sa = 1
Direction Factor Sd = 1
Seasonal Factor Ss = 1
Probably Factor Sp = 1
Site references wind speed Vs = 22.22 m/s

c. Effective Wind Speed, Ve

Effective Wind speed Ve = VsxSb

Building Height Hr = 12 m
Effective Height He = 4.8 m
Height Sb = 1.341 m
Effective Wind speed Ve = 29.79702 m/s

d. Dynamic Pressure, qs

Dynamic Pressure qs = 0.5442597 kn/m2

net pressure p = 0.5442597

e. Surface Load, P

Net load of element P = pA

Page 7
 Projected Wind Force Downforce
Element b(m) w(m) Weight (kg)
Area (m2) (kn) (kn)
Antenna 1 0.445 0.13 0.05785 0.0314854 36.2 0.3550007
Antenna 2 0.408 0.199 0.08119 0.0441900 30.0 0.2941995
RRU 0.342 0.189 0.064638 0.0351799 26.3 0.2579149

Page 8
SECTOR 1

Page 9
 Tuesday, August 24, 2021, 11:27 AM
PAGE NO. 1

****************************************************
* *
* STAAD.Pro V8i SELECTseries6 *
* Version 20.07.11.33 *
* Proprietary Program of *
* Bentley Systems, Inc. *
* Date= AUG 24, 2021 *
* Time= 11:25:52 *
* *
* USER ID: FKAAB-UTHM *
****************************************************

1. STAAD SPACE 5G JINJANG UTARA

INPUT FILE: C:\Users\fatin\OneDrive\Desktop\Sector 1\SECTOR 1.STD
2. START JOB INFORMATION
3. ENGINEER DATE 23-AUG-21
4. JOB NAME NEW STRUCTURE
5. JOB CLIENT EDOTCO MALAYSIA SDN BHD
6. JOB NO 03
7. JOB REV 0
8. JOB PART 0
9. JOB REF 5G LOAD
10. ENGINEER NAME QIS
11. CHECKER NAME ANWAR
12. END JOB INFORMATION
13. INPUT WIDTH 79
14. UNIT METER KN
15. JOINT COORDINATES
16. 1 5 4 0; 2 5 10 0; 3 5 9.55 0; 4 5.5 9.55 0; 5 4.5 9.55 0; 6 5 8.45 0
17. 7 5.5 8.45 0; 8 4.5 8.45 0; 9 4.5 10 0; 10 4.5 8 0; 11 5.5 10 0; 12 5.5 8 0
18. 13 5 7 0; 15 5 6.5 0; 17 5 4 1.5; 18 3.3 4 0
19. MEMBER INCIDENCES
20. 2 3 2; 3 6 3; 4 3 5; 5 5 9; 6 5 8; 7 8 10; 8 8 6; 9 6 7; 10 3 4; 11 4 11
21. 12 4 7; 13 7 12; 14 13 6; 16 13 15; 17 15 1; 19 5 6; 20 4 6; 22 15 17
22. 23 13 18
23. DEFINE MATERIAL START
24. ISOTROPIC STEEL
25. E 2.05E+008
26. POISSON 0.3
27. DENSITY 76.8195
28. ALPHA 1.2E-005
29. DAMP 0.03
30. TYPE STEEL
31. STRENGTH FY 253200 FU 407800 RY 1.5 RT 1.2
32. END DEFINE MATERIAL
33. MEMBER PROPERTY BRITISH
34. 22 23 TABLE ST PIP422.6
35. 2 3 14 16 17 TABLE ST PIP1143.6
36. 5 TO 7 11 TO 13 TABLE ST PIP604.0
37. 4 8 TO 10 19 20 TABLE ST UA45X45X5
38. CONSTANTS

C:\Users\fatin\OneDrive\Desktop\Sector 1\SECTOR 1.anl Page 1 of 5

 Tuesday, August 24, 2021, 11:27 AM
5G JINJANG UTARA -- PAGE NO. 2

39. MATERIAL STEEL ALL

40. SUPPORTS
41. 1 FIXED
42. 17 18 PINNED
43. LOAD 1 LOADTYPE DEAD TITLE DEAD LOAD
44. MEMBER LOAD
45. 6 CON GY -0.2942
46. 12 CON GY -0.355
47. 7 13 CON GY -0.257915
48. SELFWEIGHT Y -1
49. LOAD 2 LOADTYPE LIVE REDUCIBLE TITLE LIVE LOAD
50. MEMBER LOAD
51. 2 CON GY -1.
52. LOAD 3 LOADTYPE WIND TITLE X-DIRECTION
53. MEMBER LOAD
54. 6 CON GX 0.04419
55. 12 CON GX 0.031485
56. 7 13 CON GX 0.03518
57. 5 TO 7 11 TO 13 UNI GX 0.03266
58. 22 23 UNI GX 0.02177
59. 2 3 14 16 17 UNI GX 0.05987
60. 4 8 TO 10 19 20 UNI GX 0.02449
61. LOAD 4 LOADTYPE WIND TITLE Z-DIRECTION
62. MEMBER LOAD
63. 6 CON GZ 0.04419
64. 12 CON GZ 0.031485
65. 7 13 CON GZ 0.03518
66. 5 TO 7 11 TO 13 UNI GZ 0.03266
67. 22 23 UNI GZ 0.02177
68. 2 3 14 16 17 UNI GZ 0.05987
69. 4 8 TO 10 19 20 UNI GZ 0.02449
70. LOAD 5 LOADTYPE WIND TITLE -X DIRECTION
71. MEMBER LOAD
72. 6 CON GX -0.04419
73. 12 CON GX -0.031485
74. 7 13 CON GX -0.03518
75. 5 TO 7 11 TO 13 UNI GX -0.03266
76. 22 23 UNI GX -0.02177
77. 2 3 14 16 17 UNI GX -0.05987
78. 4 8 TO 10 19 20 UNI GX -0.02449
79. LOAD 6 LOADTYPE WIND TITLE -Z DIRECTION
80. MEMBER LOAD
81. 6 CON GZ -0.04419
82. 12 CON GZ -0.031485
83. 7 13 CON GZ -0.03518
84. 5 TO 7 11 TO 13 UNI GZ -0.03266
85. 22 23 UNI GZ -0.02177
86. 2 3 14 16 17 UNI GZ -0.05987
87. 4 8 TO 10 19 20 UNI GZ -0.02449
88. LOAD COMB 7 SERVICE LOAD
89. 1 1.0 2 1.0 3 1.0
90. LOAD COMB 8 MAX LOAD
91. 1 1.4 2 1.6
92. LOAD COMB 9 CASE 1 (X-DIR)
93. 1 1.2 2 1.2 3 1.2
94. LOAD COMB 10 CASE 2 (Z-DIR)

C:\Users\fatin\OneDrive\Desktop\Sector 1\SECTOR 1.anl Page 2 of 5

 Tuesday, August 24, 2021, 11:27 AM
5G JINJANG UTARA -- PAGE NO. 3

95. 1 1.2 2 1.2 4 1.2

96. LOAD COMB 11 CASE 3 (X-DIR) (-VE)
97. 1 1.2 2 1.2 5 1.2
98. LOAD COMB 12 CASE 4 (Z-DIR) (-VE)
99. 1 1.2 2 1.2 6 1.2
100. PERFORM ANALYSIS

P R O B L E M S T A T I S T I C S
-----------------------------------

NUMBER OF JOINTS 16 NUMBER OF MEMBERS 19

NUMBER OF PLATES 0 NUMBER OF SOLIDS 0
NUMBER OF SURFACES 0 NUMBER OF SUPPORTS 3

SOLVER USED IS THE IN-CORE ADVANCED MATH SOLVER

TOTAL PRIMARY LOAD CASES = 6, TOTAL DEGREES OF FREEDOM = 84

TOTAL LOAD COMBINATION CASES = 6 SO FAR.

101. PARAMETER 1
102. CODE BS5950
103. PY 275000 ALL
104. CHECK CODE ALL

STAAD.Pro CODE CHECKING - (BSI )

***********************

PROGRAM CODE REVISION V2.13_5950-1_2000

C:\Users\fatin\OneDrive\Desktop\Sector 1\SECTOR 1.anl Page 3 of 5

 Tuesday, August 24, 2021, 11:27 AM
5G JINJANG UTARA -- PAGE NO. 4

ALL UNITS ARE - KN METE (UNLESS OTHERWISE Noted)

MEMBER TABLE RESULT/ CRITICAL COND/ RATIO/ LOADING/

FX MY MZ LOCATION
=======================================================================

2 ST PIP1143.6 PASS BS-4.7 (C) 0.005 8

1.66 C 0.00 0.00 0.00
3 ST PIP1143.6 PASS BS-4.8.3.3.3 0.030 10
1.28 C 0.00 0.27 -
4 ST UA45X45X5 PASS BS-4.9 0.062 10
0.00 T 0.04 0.00 0.00
5 ST PIP604.0 PASS BS-4.8.3.3.1 0.002 9
0.03 C 0.00 0.00 -
6 ST PIP604.0 PASS BS-4.8.2.2 0.008 11
0.74 T 0.00 0.01 0.55
7 ST PIP604.0 PASS BS-4.8.2.2 0.006 9
0.34 T 0.00 0.01 0.00
8 ST UA45X45X5 PASS BS-4.8.3.3.1 0.097 10
0.00 0.06 0.00 -
9 ST UA45X45X5 PASS BS-4.8.3.3.1 0.090 10
0.00 C 0.05 0.00 -
10 ST UA45X45X5 PASS BS-4.9 0.057 10
0.00 T 0.03 0.00 0.00
11 ST PIP604.0 PASS BS-4.8.3.3.1 0.002 9
0.03 C 0.00 0.00 -
12 ST PIP604.0 PASS BS-4.8.2.2 0.007 9
0.80 T 0.00 0.01 0.55
13 ST PIP604.0 PASS BS-4.8.2.2 0.006 9
0.34 T 0.00 0.01 0.00
14 ST PIP1143.6 PASS ANNEX I.1 0.101 9
3.36 C 0.00 1.22 -
16 ST PIP1143.6 PASS ANNEX I.1 0.125 12
3.49 C 1.50 0.01 -
17 ST PIP1143.6 PASS ANNEX I.1 0.122 10
0.91 C 1.46 0.01 -
19 ST UA45X45X5 PASS BS-4.8.3.3.1 0.083 10
0.88 C 0.03 0.00 -
20 ST UA45X45X5 PASS BS-4.8.3.3.1 0.082 10
0.95 C 0.03 0.00 -
22 ST PIP422.6 PASS BS-4.8.3.3.1 0.280 10
3.34 C 0.00 0.04 -
23 ST PIP422.6 PASS BS-4.8.3.3.1 0.309 11
2.72 C 0.00 0.04 -

C:\Users\fatin\OneDrive\Desktop\Sector 1\SECTOR 1.anl Page 4 of 5

 Tuesday, August 24, 2021, 11:27 AM
5G JINJANG UTARA -- PAGE NO. 5

************** END OF TABULATED RESULT OF DESIGN **************

105. PERFORM ANALYSIS

106. FINISH

*********** END OF THE STAAD.Pro RUN ***********

**** DATE= AUG 24,2021 TIME= 11:25:52 ****

************************************************************
* For technical assistance on STAAD.Pro, please visit *
* http://selectservices.bentley.com/en-US/ *
* *
* Details about additional assistance from *
* Bentley and Partners can be found at program menu *
* Help->Technical Support *
* *
* Copyright (c) 1997-2015 Bentley Systems, Inc.
* http://www.bentley.com *
************************************************************

C:\Users\fatin\OneDrive\Desktop\Sector 1\SECTOR 1.anl Page 5 of 5

 Job No Sheet No Rev
03 1 0

Part 0
Software licensed to FKAAB-UTHM
Job Title NEW STRUCTURE Ref 5G LOAD
By QIS Date23-Aug-21 Chd ANWAR
Client EDOTCO MALAYSIA SDN BHD File SECTOR 1.std Date/Time 24-Aug-2021 11:21

Job Information
Engineer Checked Approved

Name: QIS ANWAR

Date: 23-Aug-21

Structure Type SPACE FRAME

Number of Nodes 16 Highest Node 18

Number of Elements 19 Highest Beam 23

Number of Basic Load Cases 6

Number of Combination Load Cases 6

Included in this printout are data for:

All The Whole Structure

Included in this printout are results for load cases:

Type L/C Name

Primary 1 DEAD LOAD

Primary 2 LIVE LOAD
Primary 3 X-DIRECTION
Primary 4 Z-DIRECTION
Primary 5 -X DIRECTION
Primary 6 -Z DIRECTION
Combination 7 SERVICE LOAD
Combination 8 MAX LOAD
Combination 9 CASE 1 (X-DIR)
Combination 10 CASE 2 (Z-DIR)
Combination 11 CASE 3 (X-DIR) (-VE)
Combination 12 CASE 4 (Z-DIR) (-VE)

Primary Load Cases

Number Name Type

1 DEAD LOAD Dead

2 LIVE LOAD Live
3 X-DIRECTION Wind
4 Z-DIRECTION Wind
5 -X DIRECTION Wind
6 -Z DIRECTION Wind

Print Time/Date: 24/08/2021 11:38 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 1 of 8
 Job No Sheet No Rev
03 2 0

Part 0
Software licensed to FKAAB-UTHM
Job Title NEW STRUCTURE Ref 5G LOAD
By QIS Date23-Aug-21 Chd ANWAR
Client EDOTCO MALAYSIA SDN BHD File SECTOR 1.std Date/Time 24-Aug-2021 11:21

Combination Load Cases

Comb. Combination L/C Name Primary Primary L/C Name Factor

7 SERVICE LOAD 1 DEAD LOAD 1.00

2 LIVE LOAD 1.00
3 X-DIRECTION 1.00
8 MAX LOAD 1 DEAD LOAD 1.40
2 LIVE LOAD 1.60
9 CASE 1 (X-DIR) 1 DEAD LOAD 1.20
2 LIVE LOAD 1.20
3 X-DIRECTION 1.20
10 CASE 2 (Z-DIR) 1 DEAD LOAD 1.20
2 LIVE LOAD 1.20
4 Z-DIRECTION 1.20
11 CASE 3 (X-DIR) (-VE) 1 DEAD LOAD 1.20
2 LIVE LOAD 1.20
5 -X DIRECTION 1.20
12 CASE 4 (Z-DIR) (-VE) 1 DEAD LOAD 1.20
2 LIVE LOAD 1.20
6 -Z DIRECTION 1.20

Node Displacement Summary

Node L/C X Y Z Resultant rX rY rZ
(mm) (mm) (mm) (mm) (rad) (rad) (rad)
Max X 2 9:CASE 1 (X-DIR) 14.273 -0.097 -0.203 14.274 -0.000 0.000 -0.005
Min X 2 11:CASE 3 (X-DIR) -13.010
(-VE) -0.039 0.024 13.010 0.000 -0.000 0.005
Max Y 5 9:CASE 1 (X-DIR) 11.858 2.518 -0.107 12.123 -0.000 0.000 -0.005
Min Y 12 9:CASE 1 (X-DIR) 3.721 -2.736 -0.225 4.624 -0.000 0.000 -0.005
Max Z 9 10:CASE 2 (Z-DIR) 0.509 0.055 21.355 21.361 0.007 0.001 -0.000
Min Z 9 12:CASE 4 (Z-DIR) (-VE)
0.741 0.021 -21.532 21.545 -0.007 -0.001 -0.000
Max rX 2 10:CASE 2 (Z-DIR) 0.515 -0.040 21.064 21.070 0.007 0.000 -0.000
Min rX 2 12:CASE 4 (Z-DIR) (-VE)
0.747 -0.096 -21.243 21.256 -0.007 -0.000 -0.000
Max rY 18 10:CASE 2 (Z-DIR) 0.000 0.000 0.000 0.000 0.002 0.002 -0.001
Min rY 18 12:CASE 4 (Z-DIR) (-VE)
0.000 0.000 0.000 0.000 -0.002 -0.002 -0.001
Max rZ 2 11:CASE 3 (X-DIR) -13.010
(-VE) -0.039 0.024 13.010 0.000 -0.000 0.005
Min rZ 2 9:CASE 1 (X-DIR) 14.273 -0.097 -0.203 14.274 -0.000 0.000 -0.005
Max Rst 9 12:CASE 4 (Z-DIR) (-VE)
0.741 0.021 -21.532 21.545 -0.007 -0.001 -0.000

Print Time/Date: 24/08/2021 11:38 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 2 of 8
 Job No Sheet No Rev
03 3 0

Part 0
Software licensed to FKAAB-UTHM
Job Title NEW STRUCTURE Ref 5G LOAD
By QIS Date23-Aug-21 Chd ANWAR
Client EDOTCO MALAYSIA SDN BHD File SECTOR 1.std Date/Time 24-Aug-2021 11:21

Beam Force Detail Summary

Sign convention as diagrams:- positive above line, negative below line except Fx where positive is compression. Distance d is given from
beam end A.
Axial Shear Torsion Bending
Beam L/C d Fx Fy Fz Mx My Mz
(m) (kN) (kN) (kN) (kNm) (kNm) (kNm)
Max Fx 17 12:CASE 4 (Z-DIR) (-VE)
2.500 6.715 -0.000 0.712 0.041 0.576 -0.011
Min Fx 22 12:CASE 4 (Z-DIR) (-VE)
0.000 -3.380 0.080 0.001 -0.000 -0.003 0.072
Max Fy 14 9:CASE 1 (X-DIR) 0.000 3.363 0.677 0.000 -0.000 -0.000 1.218
Min Fy 14 11:CASE 3 (X-DIR) (-VE)
0.000 3.363 -0.677 -0.000 0.000 0.000 -1.145
Max Fz 17 12:CASE 4 (Z-DIR) (-VE)
0.000 6.427 -0.000 0.892 0.041 -1.428 -0.011
Min Fz 17 10:CASE 2 (Z-DIR) 0.000 0.619 -0.007 -0.920 -0.042 1.460 -0.013
Max Mx 16 12:CASE 4 (Z-DIR) (-VE)
0.000 3.430 -0.001 -0.743 0.043 -1.120 -0.014
Min Mx 16 10:CASE 2 (Z-DIR) 0.000 3.439 -0.006 0.743 -0.043 1.120 -0.014
Max My 16 10:CASE 2 (Z-DIR) 0.500 3.497 -0.006 0.779 -0.043 1.500 -0.011
Min My 16 12:CASE 4 (Z-DIR) (-VE)
0.500 3.488 -0.001 -0.779 0.043 -1.500 -0.013
Max Mz 14 9:CASE 1 (X-DIR) 0.000 3.363 0.677 0.000 -0.000 -0.000 1.218
Min Mz 14 11:CASE 3 (X-DIR) (-VE)
0.000 3.363 -0.677 -0.000 0.000 0.000 -1.145

Reaction Summary
Horizontal Vertical Horizontal Moment
Node L/C FX FY FZ MX MY MZ
(kN) (kN) (kN) (kNm) (kNm) (kNm)
Max FX 18 11:CASE 3 (X-DIR) (-VE)
1.413 2.486 0.000 0.000 0.000 0.000
Min FX 18 9:CASE 1 (X-DIR) -1.420 -2.421 -0.000 0.000 0.000 0.000
Max FY 1 12:CASE 4 (Z-DIR) (-VE)
0.000 6.715 -0.712 -0.576 0.041 0.011
Min FY 17 12:CASE 4 (Z-DIR) (-VE)
0.001 -2.852 1.747 0.000 0.000 0.000
Max FZ 17 12:CASE 4 (Z-DIR) (-VE)
0.001 -2.852 1.747 0.000 0.000 0.000
Min FZ 17 10:CASE 2 (Z-DIR) -0.001 2.964 -1.775 0.000 0.000 0.000
Max MX 1 10:CASE 2 (Z-DIR) 0.007 0.907 0.740 0.614 -0.042 -0.004
Min MX 1 12:CASE 4 (Z-DIR) (-VE)
0.000 6.715 -0.712 -0.576 0.041 0.011
Max MY 1 12:CASE 4 (Z-DIR) (-VE)
0.000 6.715 -0.712 -0.576 0.041 0.011
Min MY 1 10:CASE 2 (Z-DIR) 0.007 0.907 0.740 0.614 -0.042 -0.004
Max MZ 1 11:CASE 3 (X-DIR) (-VE)
-0.378 1.363 0.011 0.011 0.020 0.407
Min MZ 1 9:CASE 1 (X-DIR) 0.385 6.259 0.017 0.027 -0.020 -0.401

Failed Members
There is no data of this type.

Print Time/Date: 24/08/2021 11:38 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 3 of 8
 Job No Sheet No Rev
03 4 0

Part 0
Software licensed to FKAAB-UTHM
Job Title NEW STRUCTURE Ref 5G LOAD
By QIS Date23-Aug-21 Chd ANWAR
Client EDOTCO MALAYSIA SDN BHD File SECTOR 1.std Date/Time 24-Aug-2021 11:21

6.000m

Y
X
Z Load 1

Whole Structure

6.000m

Y
X
Z Load 1

Whole Structure

Print Time/Date: 24/08/2021 11:38 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 4 of 8
 Job No Sheet No Rev
03 5 0

Part 0
Software licensed to FKAAB-UTHM
Job Title NEW STRUCTURE Ref 5G LOAD
By QIS Date23-Aug-21 Chd ANWAR
Client EDOTCO MALAYSIA SDN BHD File SECTOR 1.std Date/Time 24-Aug-2021 11:21

6.000m

Y
X
Z Load 1

Whole Structure

6.000m

Y
X
Z Load 2

Whole Structure

Print Time/Date: 24/08/2021 11:38 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 5 of 8
 Job No Sheet No Rev
03 6 0

Part 0
Software licensed to FKAAB-UTHM
Job Title NEW STRUCTURE Ref 5G LOAD
By QIS Date23-Aug-21 Chd ANWAR
Client EDOTCO MALAYSIA SDN BHD File SECTOR 1.std Date/Time 24-Aug-2021 11:21

6.000m

Y
X
Z Load 3

Whole Structure

6.000m

Y
X
Z Load 4

Whole Structure

Print Time/Date: 24/08/2021 11:38 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 6 of 8
 Job No Sheet No Rev
03 7 0

Part 0
Software licensed to FKAAB-UTHM
Job Title NEW STRUCTURE Ref 5G LOAD
By QIS Date23-Aug-21 Chd ANWAR
Client EDOTCO MALAYSIA SDN BHD File SECTOR 1.std Date/Time 24-Aug-2021 11:21

6.000m

Y
X
Z Load 5

Whole Structure

6.000m

Y
X
Z Load 6

Whole Structure

Print Time/Date: 24/08/2021 11:38 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 7 of 8
 Job No Sheet No Rev
03 8 0

Part 0
Software licensed to FKAAB-UTHM
Job Title NEW STRUCTURE Ref 5G LOAD
By QIS Date23-Aug-21 Chd ANWAR
Client EDOTCO MALAYSIA SDN BHD File SECTOR 1.std Date/Time 24-Aug-2021 11:21

0.0017
0.00483
0.0017 0.0565
0.0619
0.00738
0.0825
0.0299
0.0831
0.00791
0.09
0.0967 0.0056
0.0056
0.101

6.000m
0.125

0.309 0.122
0.28

Y
X
Z Load 6

Whole Structure

Print Time/Date: 24/08/2021 11:38 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 8 of 8
SECTOR 2 AND 3

Page 23
 Monday, August 23, 2021, 03:22 PM
PAGE NO. 1

****************************************************
* *
* STAAD.Pro V8i SELECTseries6 *
* Version 20.07.11.33 *
* Proprietary Program of *
* Bentley Systems, Inc. *
* Date= AUG 23, 2021 *
* Time= 15:16: 2 *
* *
* USER ID: *
****************************************************

1. STAAD SPACE 5G JINJANG UTARA

INPUT FILE: C:\Users\ACER\Desktop\Foursons\August\WEEK8\23.8.21\STAADPRO\PROPOSE NEW STRUCTURE 5G JINJ.. .STD
2. START JOB INFORMATION
3. ENGINEER DATE 20-AUG-21
4. JOB NAME NEW STRUCTURE
5. JOB CLIENT EDOTCO MALAYSIA SDN BHD
6. JOB NO 03
7. JOB REV 0
8. JOB PART 0
9. JOB REF 5G LOAD
10. ENGINEER NAME ZKW
11. CHECKER NAME MAD
12. END JOB INFORMATION
13. INPUT WIDTH 79
14. UNIT METER KN
15. JOINT COORDINATES
16. 1 5 4 0; 2 5 10 0; 3 5 9.55 0; 4 5.5 9.55 0; 5 4.5 9.55 0; 6 5 8.45 0
17. 7 5.5 8.45 0; 8 4.5 8.45 0; 9 4.5 10 0; 10 4.5 8 0; 11 5.5 10 0; 12 5.5 8 0
18. 13 5 7 0; 14 6.5 4 0; 15 5 6.5 0; 17 5 4 1.5
19. MEMBER INCIDENCES
20. 2 3 2; 3 6 3; 4 3 5; 5 5 9; 6 5 8; 7 8 10; 8 8 6; 9 6 7; 10 3 4; 11 4 11
21. 12 4 7; 13 7 12; 14 13 6; 15 13 14; 16 13 15; 17 15 1; 19 5 6; 20 4 6
22. 22 15 17
23. DEFINE MATERIAL START
24. ISOTROPIC STEEL
25. E 2.05E+008
26. POISSON 0.3
27. DENSITY 76.8195
28. ALPHA 1.2E-005
29. DAMP 0.03
30. TYPE STEEL
31. STRENGTH FY 253200 FU 407800 RY 1.5 RT 1.2
32. END DEFINE MATERIAL
33. MEMBER PROPERTY BRITISH
34. 15 22 TABLE ST PIP422.6
35. 2 3 14 16 17 TABLE ST PIP1143.6
36. 5 TO 7 11 TO 13 TABLE ST PIP604.0
37. 4 8 TO 10 19 20 TABLE ST UA45X45X5
38. CONSTANTS

C:\Users\ACER\Desktop\Foursons\August\WEEK8\23.8.21\STAADPRO\PROPOSE NEW STRUCTURE 5G JINJANG UTARA REV0.1.anl

Page 1 of 5
 Monday, August 23, 2021, 03:22 PM
5G JINJANG UTARA -- PAGE NO. 2

39. MATERIAL STEEL ALL

40. SUPPORTS
41. 1 FIXED
42. 14 17 PINNED
43. LOAD 1 LOADTYPE DEAD TITLE DEAD LOAD
44. MEMBER LOAD
45. 6 CON GY -0.2942
46. 12 CON GY -0.355
47. 7 13 CON GY -0.257915
48. SELFWEIGHT Y -1
49. LOAD 2 LOADTYPE LIVE REDUCIBLE TITLE LIVE LOAD
50. MEMBER LOAD
51. 2 CON GY -1.
52. LOAD 3 LOADTYPE WIND TITLE X-DIRECTION
53. MEMBER LOAD
54. 6 CON GX 0.04419
55. 12 CON GX 0.031485
56. 7 13 CON GX 0.03518
57. 5 TO 7 11 TO 13 UNI GX 0.03266
58. 15 22 UNI GX 0.02177
59. 2 3 14 16 17 UNI GX 0.05987
60. 4 8 TO 10 19 20 UNI GX 0.02449
61. LOAD 4 LOADTYPE WIND TITLE Z-DIRECTION
62. MEMBER LOAD
63. 6 CON GZ 0.04419
64. 12 CON GZ 0.031485
65. 7 13 CON GZ 0.03518
66. 5 TO 7 11 TO 13 UNI GZ 0.03266
67. 15 22 UNI GZ 0.02177
68. 2 3 14 16 17 UNI GZ 0.05987
69. 4 8 TO 10 19 20 UNI GZ 0.02449
70. LOAD 5 LOADTYPE WIND TITLE -X DIRECTION
71. MEMBER LOAD
72. 6 CON GX -0.04419
73. 12 CON GX -0.031485
74. 7 13 CON GX -0.03518
75. 5 TO 7 11 TO 13 UNI GX -0.03266
76. 15 22 UNI GX -0.02177
77. 2 3 14 16 17 UNI GX -0.05987
78. 4 8 TO 10 19 20 UNI GX -0.02449
79. LOAD 6 LOADTYPE WIND TITLE -Z DIRECTION
80. MEMBER LOAD
81. 6 CON GZ -0.04419
82. 12 CON GZ -0.031485
83. 7 13 CON GZ -0.03518
84. 5 TO 7 11 TO 13 UNI GZ -0.03266
85. 15 22 UNI GZ -0.02177
86. 2 3 14 16 17 UNI GZ -0.05987
87. 4 8 TO 10 19 20 UNI GZ -0.02449
88. LOAD COMB 7 SERVICE LOAD
89. 1 0.0 2 0.0 3 0.0
90. LOAD COMB 8 MAX LOAD
91. 1 1.4 2 1.6
92. LOAD COMB 9 CASE 1 X DIRECTION
93. 1 1.2 2 1.2 3 1.2
94. LOAD COMB 10 CASE 2 Z DIRECTION

C:\Users\ACER\Desktop\Foursons\August\WEEK8\23.8.21\STAADPRO\PROPOSE NEW STRUCTURE 5G JINJANG UTARA REV0.1.anl

Page 2 of 5
 Monday, August 23, 2021, 03:22 PM
5G JINJANG UTARA -- PAGE NO. 3

95. 1 1.2 2 1.2 4 1.2

96. LOAD COMB 11 CASE 3 -X DIRECTION
97. 1 1.2 2 1.2 5 1.2
98. LOAD COMB 12 CASE 4 -X Z DIRECTION
99. 1 1.2 2 1.2 6 1.2
100. PERFORM ANALYSIS

P R O B L E M S T A T I S T I C S
-----------------------------------

NUMBER OF JOINTS 16 NUMBER OF MEMBERS 19

NUMBER OF PLATES 0 NUMBER OF SOLIDS 0
NUMBER OF SURFACES 0 NUMBER OF SUPPORTS 3

SOLVER USED IS THE OUT-OF-CORE BASIC SOLVER

ORIGINAL/FINAL BAND-WIDTH= 14/ 5/ 36 DOF

TOTAL PRIMARY LOAD CASES = 6, TOTAL DEGREES OF FREEDOM = 84
TOTAL LOAD COMBINATION CASES = 6 SO FAR.
SIZE OF STIFFNESS MATRIX = 4 DOUBLE KILO-WORDS
REQRD/AVAIL. DISK SPACE = 12.1/ 245652.1 MB

101. PARAMETER 1
102. CODE BS5950
103. PY 275000 ALL
104. CHECK CODE ALL

STAAD.Pro CODE CHECKING - (BSI )

***********************

PROGRAM CODE REVISION V2.13_5950-1_2000

C:\Users\ACER\Desktop\Foursons\August\WEEK8\23.8.21\STAADPRO\PROPOSE NEW STRUCTURE 5G JINJANG UTARA REV0.1.anl

Page 3 of 5
 Monday, August 23, 2021, 03:22 PM
5G JINJANG UTARA -- PAGE NO. 4

ALL UNITS ARE - KN METE (UNLESS OTHERWISE Noted)

MEMBER TABLE RESULT/ CRITICAL COND/ RATIO/ LOADING/

FX MY MZ LOCATION
=======================================================================

2 ST PIP1143.6 PASS BS-4.7 (C) 0.005 8

1.66 C 0.00 0.00 0.00
3 ST PIP1143.6 PASS BS-4.8.3.3.3 0.030 10
1.28 C 0.00 0.27 -
4 ST UA45X45X5 PASS BS-4.9 0.062 10
0.00 T 0.04 0.00 0.00
5 ST PIP604.0 PASS BS-4.8.3.3.1 0.002 9
0.03 C 0.00 0.00 -
6 ST PIP604.0 PASS BS-4.8.2.2 0.008 11
0.74 T 0.00 0.01 0.55
7 ST PIP604.0 PASS BS-4.8.2.2 0.006 9
0.34 T 0.00 0.01 0.00
8 ST UA45X45X5 PASS BS-4.8.3.3.1 0.097 10
0.00 0.06 0.00 -
9 ST UA45X45X5 PASS BS-4.8.3.3.1 0.090 10
0.00 C 0.05 0.00 -
10 ST UA45X45X5 PASS BS-4.9 0.057 10
0.00 T 0.03 0.00 0.00
11 ST PIP604.0 PASS BS-4.8.3.3.1 0.002 9
0.03 C 0.00 0.00 -
12 ST PIP604.0 PASS BS-4.8.2.2 0.007 9
0.80 T 0.00 0.01 0.55
13 ST PIP604.0 PASS BS-4.8.2.2 0.006 9
0.34 T 0.00 0.01 0.00
14 ST PIP1143.6 PASS ANNEX I.1 0.101 9
3.36 C 0.00 1.22 -
15 ST PIP422.6 PASS BS-4.8.3.3.1 0.331 9
3.08 C 0.00 0.04 -
16 ST PIP1143.6 PASS ANNEX I.1 0.128 12
3.42 C 1.50 0.05 -
17 ST PIP1143.6 PASS ANNEX I.1 0.124 12
6.64 C 1.43 0.04 -
19 ST UA45X45X5 PASS BS-4.8.3.3.1 0.083 10
0.88 C 0.03 0.00 -
20 ST UA45X45X5 PASS BS-4.8.3.3.1 0.082 10
0.95 C 0.03 0.00 -
22 ST PIP422.6 PASS BS-4.8.3.3.1 0.279 10
3.34 C 0.00 0.04 -

C:\Users\ACER\Desktop\Foursons\August\WEEK8\23.8.21\STAADPRO\PROPOSE NEW STRUCTURE 5G JINJANG UTARA REV0.1.anl

Page 4 of 5
 Monday, August 23, 2021, 03:22 PM
5G JINJANG UTARA -- PAGE NO. 5

************** END OF TABULATED RESULT OF DESIGN **************

105. FINISH

*********** END OF THE STAAD.Pro RUN ***********

**** DATE= AUG 23,2021 TIME= 15:16: 4 ****

************************************************************
* For technical assistance on STAAD.Pro, please visit *
* http://selectservices.bentley.com/en-US/ *
* *
* Details about additional assistance from *
* Bentley and Partners can be found at program menu *
* Help->Technical Support *
* *
* Copyright (c) 1997-2015 Bentley Systems, Inc.
* http://www.bentley.com *
************************************************************

C:\Users\ACER\Desktop\Foursons\August\WEEK8\23.8.21\STAADPRO\PROPOSE NEW STRUCTURE 5G JINJANG UTARA REV0.1.anl

Page 5 of 5
 Job No Sheet No Rev
03 1 0

Part 0
Software licensed to
Job Title NEW STRUCTURE Ref 5G LOAD
By ZKW Date20-Aug-21 Chd MAD
Client EDOTCO MALAYSIA SDN BHD File PROPOSE NEW Date/Time
STRUCTURE 5G23-Aug-2021
JINJANG UTARA
15:15REV0.1.std

Job Information
Engineer Checked Approved

Name: ZKW MAD

Date: 20-Aug-21

Structure Type SPACE FRAME

Number of Nodes 16 Highest Node 17

Number of Elements 19 Highest Beam 22

Number of Basic Load Cases 6

Number of Combination Load Cases 6

Included in this printout are data for:

All The Whole Structure

Included in this printout are results for load cases:

Type L/C Name

Primary 1 DEAD LOAD

Primary 2 LIVE LOAD
Primary 3 X-DIRECTION
Primary 4 Z-DIRECTION
Primary 5 -X DIRECTION
Primary 6 -Z DIRECTION
Combination 7 SERVICE LOAD
Combination 8 MAX LOAD
Combination 9 CASE 1 X DIRECTION
Combination 10 CASE 2 Z DIRECTION
Combination 11 CASE 3 -X DIRECTION
Combination 12 CASE 4 -X Z DIRECTION

Primary Load Cases

Number Name Type

1 DEAD LOAD Dead

2 LIVE LOAD Live
3 X-DIRECTION Wind
4 Z-DIRECTION Wind
5 -X DIRECTION Wind
6 -Z DIRECTION Wind

Print Time/Date: 23/08/2021 15:21 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 1 of 8
 Job No Sheet No Rev
03 2 0

Part 0
Software licensed to
Job Title NEW STRUCTURE Ref 5G LOAD
By ZKW Date20-Aug-21 Chd MAD
Client EDOTCO MALAYSIA SDN BHD File PROPOSE NEW Date/Time
STRUCTURE 5G23-Aug-2021
JINJANG UTARA
15:15REV0.1.std

Combination Load Cases

Comb. Combination L/C Name Primary Primary L/C Name Factor

7 SERVICE LOAD 1 DEAD LOAD 0.00

2 LIVE LOAD 0.00
3 X-DIRECTION 0.00
8 MAX LOAD 1 DEAD LOAD 1.40
2 LIVE LOAD 1.60
9 CASE 1 X DIRECTION 1 DEAD LOAD 1.20
2 LIVE LOAD 1.20
3 X-DIRECTION 1.20
10 CASE 2 Z DIRECTION 1 DEAD LOAD 1.20
2 LIVE LOAD 1.20
4 Z-DIRECTION 1.20
11 CASE 3 -X DIRECTION 1 DEAD LOAD 1.20
2 LIVE LOAD 1.20
5 -X DIRECTION 1.20
12 CASE 4 -X Z DIRECTION 1 DEAD LOAD 1.20
2 LIVE LOAD 1.20
6 -Z DIRECTION 1.20

Node Displacement Summary

Node L/C X Y Z Resultant rX rY rZ
(mm) (mm) (mm) (mm) (rad) (rad) (rad)
Max X 2 9:CASE 1 X DIRECTION
14.287 -0.035 0.043 14.287 0.000 0.000 -0.005
Min X 2 11:CASE 3 -X DIRECTION
-13.332 -0.100 -0.216 13.334 -0.000 -0.000 0.005
Max Y 5 9:CASE 1 X DIRECTION
11.857 2.597 0.119 12.139 0.000 0.000 -0.005
Min Y 12 9:CASE 1 X DIRECTION3.668 -2.691 -0.071 4.549 0.000 0.000 -0.005
Max Z 11 10:CASE 2 Z DIRECTION
0.606 -0.177 21.187 21.197 0.007 -0.001 -0.000
Min Z 11 12:CASE 4 -X Z DIRECTION
0.336 -0.208 -21.362 21.365 -0.007 0.001 -0.000
Max rX 2 10:CASE 2 Z DIRECTION
0.612 -0.039 21.040 21.049 0.007 -0.000 -0.000
Min rX 2 12:CASE 4 -X Z DIRECTION
0.343 -0.095 -21.212 21.215 -0.007 0.000 -0.000
Max rY 14 12:CASE 4 -X Z DIRECTION
0.000 0.000 0.000 0.000 -0.002 0.002 0.001
Min rY 14 10:CASE 2 Z DIRECTION
0.000 0.000 0.000 0.000 0.001 -0.002 0.001
Max rZ 2 11:CASE 3 -X DIRECTION
-13.332 -0.100 -0.216 13.334 -0.000 -0.000 0.005
Min rZ 2 9:CASE 1 X DIRECTION
14.287 -0.035 0.043 14.287 0.000 0.000 -0.005
Max Rst 11 12:CASE 4 -X Z DIRECTION
0.336 -0.208 -21.362 21.365 -0.007 0.001 -0.000

Print Time/Date: 23/08/2021 15:21 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 2 of 8
 Job No Sheet No Rev
03 3 0

Part 0
Software licensed to
Job Title NEW STRUCTURE Ref 5G LOAD
By ZKW Date20-Aug-21 Chd MAD
Client EDOTCO MALAYSIA SDN BHD File PROPOSE NEW Date/Time
STRUCTURE 5G23-Aug-2021
JINJANG UTARA
15:15REV0.1.std

Beam Force Detail Summary

Sign convention as diagrams:- positive above line, negative below line except Fx where positive is compression. Distance d is given from
beam end A.
Axial Shear Torsion Bending
Beam L/C d Fx Fy Fz Mx My Mz
(m) (kN) (kN) (kN) (kNm) (kNm) (kNm)
Max Fx 17 12:CASE 4 -X Z DIRECTION
2.500 6.641 -0.033 0.710 -0.024 0.575 0.045
Min Fx 22 12:CASE 4 -X Z DIRECTION
0.000 -3.376 0.080 -0.000 0.000 0.001 0.072
Max Fy 14 9:CASE 1 X DIRECTION
0.000 3.363 0.677 -0.000 -0.000 0.000 1.218
Min Fy 14 11:CASE 3 -X DIRECTION
0.000 3.363 -0.677 0.000 -0.000 -0.000 -1.145
Max Fz 17 12:CASE 4 -X Z DIRECTION
0.000 6.353 -0.033 0.890 -0.024 -1.426 -0.039
Min Fz 17 10:CASE 2 Z DIRECTION
0.000 0.554 -0.027 -0.918 0.024 1.458 -0.039
Max Mx 16 10:CASE 2 Z DIRECTION
0.000 3.370 -0.028 0.743 0.025 1.117 -0.054
Min Mx 16 12:CASE 4 -X Z DIRECTION
0.000 3.359 -0.033 -0.743 -0.024 -1.117 -0.054
Max My 16 10:CASE 2 Z DIRECTION
0.500 3.428 -0.028 0.779 0.025 1.497 -0.040
Min My 16 12:CASE 4 -X Z DIRECTION
0.500 3.417 -0.033 -0.778 -0.024 -1.497 -0.038
Max Mz 14 9:CASE 1 X DIRECTION
0.000 3.363 0.677 -0.000 -0.000 0.000 1.218
Min Mz 16 9:CASE 1 X DIRECTION
0.000 0.592 -0.676 0.000 0.000 -0.001 -1.178

Reaction Summary
Horizontal Vertical Horizontal Moment
Node L/C FX FY FZ MX MY MZ
(kN) (kN) (kN) (kNm) (kNm) (kNm)
Max FX 14 11:CASE 3 -X DIRECTION
1.380 -2.673 -0.000 0.000 0.000 0.000
Min FX 14 9:CASE 1 X DIRECTION
-1.441 2.871 0.000 0.000 0.000 0.000
Max FY 1 12:CASE 4 -X Z DIRECTION
0.033 6.641 -0.710 -0.575 -0.024 -0.045
Min FY 17 12:CASE 4 -X Z DIRECTION
-0.000 -2.849 1.745 0.000 0.000 0.000
Max FZ 17 12:CASE 4 -X Z DIRECTION
-0.000 -2.849 1.745 0.000 0.000 0.000
Min FZ 17 10:CASE 2 Z DIRECTION
0.001 2.961 -1.773 0.000 0.000 0.000
Max MX 1 10:CASE 2 Z DIRECTION
0.027 0.842 0.738 0.613 0.024 -0.029
Min MX 1 12:CASE 4 -X Z DIRECTION
0.033 6.641 -0.710 -0.575 -0.024 -0.045
Max MY 1 10:CASE 2 Z DIRECTION
0.027 0.842 0.738 0.613 0.024 -0.029
Min MY 1 12:CASE 4 -X Z DIRECTION
0.033 6.641 -0.710 -0.575 -0.024 -0.045
Max MZ 1 11:CASE 3 -X DIRECTION
-0.348 6.508 0.018 0.027 0.020 0.358
Min MZ 1 9:CASE 1 X DIRECTION
0.409 0.975 0.010 0.010 -0.020 -0.432

Failed Members
There is no data of this type.

Print Time/Date: 23/08/2021 15:21 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 3 of 8
 Job No Sheet No Rev
03 4 0

Part 0
Software licensed to
Job Title NEW STRUCTURE Ref 5G LOAD
By ZKW Date20-Aug-21 Chd MAD
Client EDOTCO MALAYSIA SDN BHD File PROPOSE NEW Date/Time
STRUCTURE 5G23-Aug-2021
JINJANG UTARA
15:15REV0.1.std

6.000m

Y
X
Z Load 1

Whole Structure

6.000m

Y
X
Z Load 1

Whole Structure

Print Time/Date: 23/08/2021 15:21 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 4 of 8
 Job No Sheet No Rev
03 5 0

Part 0
Software licensed to
Job Title NEW STRUCTURE Ref 5G LOAD
By ZKW Date20-Aug-21 Chd MAD
Client EDOTCO MALAYSIA SDN BHD File PROPOSE NEW Date/Time
STRUCTURE 5G23-Aug-2021
JINJANG UTARA
15:15REV0.1.std

6.000m

Y
X
Z Load 1

Whole Structure

6.000m

Y
X
Z Load 2

Whole Structure

Print Time/Date: 23/08/2021 15:21 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 5 of 8
 Job No Sheet No Rev
03 6 0

Part 0
Software licensed to
Job Title NEW STRUCTURE Ref 5G LOAD
By ZKW Date20-Aug-21 Chd MAD
Client EDOTCO MALAYSIA SDN BHD File PROPOSE NEW Date/Time
STRUCTURE 5G23-Aug-2021
JINJANG UTARA
15:15REV0.1.std

6.000m

Y
X
Z Load 3

Whole Structure

6.000m

Y
X
Z Load 4

Whole Structure

Print Time/Date: 23/08/2021 15:21 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 6 of 8
 Job No Sheet No Rev
03 7 0

Part 0
Software licensed to
Job Title NEW STRUCTURE Ref 5G LOAD
By ZKW Date20-Aug-21 Chd MAD
Client EDOTCO MALAYSIA SDN BHD File PROPOSE NEW Date/Time
STRUCTURE 5G23-Aug-2021
JINJANG UTARA
15:15REV0.1.std

6.000m

Y
X
Z Load 5

Whole Structure

6.000m

Y
X
Z Load 6

Whole Structure

Print Time/Date: 23/08/2021 15:21 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 7 of 8
 Job No Sheet No Rev
03 8 0

Part 0
Software licensed to
Job Title NEW STRUCTURE Ref 5G LOAD
By ZKW Date20-Aug-21 Chd MAD
Client EDOTCO MALAYSIA SDN BHD File PROPOSE NEW Date/Time
STRUCTURE 5G23-Aug-2021
JINJANG UTARA
15:15REV0.1.std

0.0017
0.00483
0.0017 0.0565
0.0619
0.00738
0.0825
0.0299
0.0831
0.00791
0.09
0.0967 0.0056
0.0056
0.101

6.000m
0.128

0.331

0.124

0.279

Y
X
Z Load 6

Whole Structure

Print Time/Date: 23/08/2021 15:21 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 8 of 8
ANALYSIS OF STRUCTURE

Page 37
 Project Job Ref.
JINJANGUTARA3
Section Sheet no./rev.
BOLT POLE 1
Calc. by Date Chk'd by Date App'd by Date
FATIN 13-Sep-21 ANWAR

BOLT GROUP ANALYSIS

Tedds calculation version 1.0.04

Geometry of bolt group

Number of rows; R=2
Number of columns; C=2
Pitch distance; Sx = 210 mm
Gauge distance; Sy = 210 mm
Edge distance in vertical direction; dy = 45 mm
Edge distance in horizontal direction; dx = 45 mm
Load data
Vertical load applied on bolt group; Py = 7.000 kN
Horizontal load applied on bolt group; Px = 1.000 kN
X coordinate of vertical force; X = 100 mm
Y coordinate of horizontal force; Y = 100 mm
Center of gravity of bolt group
X distance of center of bolt group; Xc = ((C – 1)  Sx) / 2 + dx = 150 mm
Y distance of center of bolt group; Yc = ((R – 1)  Sy) / 2 + dy = 150 mm

Load eccentricity from center of gravity of bolt group

Eccentricity of vertical load from C.G.; ex = abs(X – Xc) = 50 mm
Eccentricity of horizontal load from C.G. ; ey = abs(Y – Yc) = 50 mm
Moment about center of gravity ; M = Px  (Y – Yc) - Py  (X – Xc) = 0.300 kNm
 Project Job Ref.
JINJANGUTARA3
Section Sheet no./rev.
BOLT POLE 2
Calc. by Date Chk'd by Date App'd by Date
FATIN 13-Sep-21 ANWAR

Bolt Bolt distance from centre Direct shear Torsional shear Total force
number of gravity
Xi (mm) Yi (mm) Pdx (kN) Pdy (kN) Ptx (kN) Pty (kN) (kN);
1 -105 -105 -0.2 -1.7 0.4 -0.4 2.1
2 105 -105 -0.2 -1.7 0.4 0.4 1.4
3 -105 105 -0.2 -1.7 -0.4 -0.4 2.2
4 105 105 -0.2 -1.7 -0.4 0.4 1.5

BOLT GROUP ANALYSIS

Tedds calculation version 1.0.04

Geometry of bolt group

Number of rows; R=2
Number of columns; C=2
Pitch distance; Sx = 120 mm
Gauge distance; Sy = 120 mm
Edge distance in vertical direction; dy = 40 mm
Edge distance in horizontal direction; dx = 40 mm
Load data
Vertical load applied on bolt group; Py = 3.000 kN
Horizontal load applied on bolt group; Px = 2.000 kN
X coordinate of vertical force; X = 100 mm
Y coordinate of horizontal force; Y = 100 mm
Center of gravity of bolt group
X distance of center of bolt group; Xc = ((C – 1)  Sx) / 2 + dx = 100 mm
 Project Job Ref.
JINJANGUTARA3
Section Sheet no./rev.
BOLT POLE 3
Calc. by Date Chk'd by Date App'd by Date
FATIN 13-Sep-21 ANWAR

Y distance of center of bolt group; Yc = ((R – 1)  Sy) / 2 + dy = 100 mm

Load eccentricity from center of gravity of bolt group

Eccentricity of vertical load from C.G.; ex = abs(X – Xc) = 0 mm
Eccentricity of horizontal load from C.G. ; ey = abs(Y – Yc) = 0 mm
Moment about center of gravity ; M = Px  (Y – Yc) - Py  (X – Xc) = 0.000 kNm

Bolt Bolt distance from centre Direct shear Torsional shear Total force
number of gravity
Xi (mm) Yi (mm) Pdx (kN) Pdy (kN) Ptx (kN) Pty (kN) (kN);
1 -60 -60 -0.5 -0.7 0.0 0.0 0.9
2 60 -60 -0.5 -0.7 0.0 0.0 0.9
3 -60 60 -0.5 -0.7 0.0 0.0 0.9
4 60 60 -0.5 -0.7 0.0 0.0 0.9

COLUMN BASE PLATE DESIGN (BS5950-1:2000)

TEDDS calculation version 1.0.09;

Base plate reference; Tension + moment;

Design forces and moments
Axial force; Fc = ;7.0; kN (Compression)
Bending moment; M = 0.6 kNm; (about major axis)
Shear force; Fv = 0.7 kN
Column details
Column section; SHS 60x60x3.0 (Grade S275)
 Project Job Ref.
JINJANGUTARA3
Section Sheet no./rev.
BOLT POLE 4
Calc. by Date Chk'd by Date App'd by Date
FATIN 13-Sep-21 ANWAR

Depth; D = 60.0 mm
Breadth; B = 60.0 mm
Flange thickness; T = 3.0 mm
Web thickness; t = 3.0 mm
Design strength; pyc = 275 N/mm2
Column flange to base plate weld; 3 mm FW;
Column web to base plate weld; 3 mm FW;
Baseplate details
Steel grade; S275
Depth; Dp = 300 mm
Breadth; Bp = 300 mm
Thickness; tp = 12 mm
Design strength; pyp = 275 N/mm2
Stiffener details
Steel grade; S275
Thickness; ts = 4 mm
Design strength; pys = 275 N/mm2
Depth at edge of baseplate; ds1 = 0 mm
Depth at column flange; ds2 = 125 mm
Stiffener to base plate weld; 4 mm FW
Stiffener to column weld; 4 mm FW (2 no. vertical welds per stiffener)
Holding down bolt and anchor plate details
Total number of bolts; 4 No. M16 Grade 8.8
Bolt spacing; sbolt1 = ;210; mm
Edge distance; e1 = 45 mm
Anchor plate steel grade; S275
Anchor plate dimension (square); bap = 135 mm
Anchor plate thickness; tap = 30 mm
Design strength; pyap = 275 N/mm2
Embeddment to top of anchor plate; E = 450 mm
Characteristic strength of concrete; fcu = 25 N/mm2
Concrete compression force and bolt tension force
To determine approximate effective width of baseplate, assume base plate between stiffeners acts as a fixed ended beam:-
Moment at stiffener; Ms = wls2/12 where ls is span between stiffeners
Moment due to cantilever outside stiffeners; Mc = wlc2/2 where lc is cantilever span beyond stiffeners
Equating the two moments; lc = ls/6
Distance between stiffener centrelines; ls = B + ts = ;64.0; mm
Cantilever span; lc = ls/(6) = 26.1 mm
Effective width of plate; Bpc = min(Bp, ls + 2lc) = 116.3 mm
Distance from bolts to compression edge; h = Dp - e1 = 255 mm
Assuming a rectangular compression block of width bpc, length x and intensity 0.6f cu then:-
From static equilibrium; M = 0.6fcuBpcx(h-x/2) - Fc(h-Dp/2)
Rearranging the quadratic equation; 0.3fcuBpcx2 - 0.6fcuBpchx + Fc(h-Dp/2) + M = 0
Factor a; a = 0.3  fcu  Bpc = 871.9 N/mm
 Project Job Ref.
JINJANGUTARA3
Section Sheet no./rev.
BOLT POLE 5
Calc. by Date Chk'd by Date App'd by Date
FATIN 13-Sep-21 ANWAR

Factor b; b = -0.6  fcu  Bpc  h = -444678.4 N

Constant c; c = Fc  (h-Dp/2) + M = 1349000.0 Nmm
Depth of compression block; x = [-1.0b - (b2 - 4ac)]/(2a) = 3.1 mm
Compression force in concrete; Cf = 0.6  fcu  Bpc  x = 5.3 kN
Tension force in bolts; Tf = Cf - Fc = -1.7 kN
Therefore the bolts are not in tension - Recalculate depth of compression block
Actual compression force in concrete; Cf = Fc = 7 kN
Actual force in bolts; Tf = 0 kN
Eccentricity of compression force; e = M/Fc = 87.7 mm
Depth of compression block; x = 2  (Dp/2 - e) = 124.6 mm
Stress in concrete; fc = Fc / (Bpc  x) = 0.5 N/mm2

Compression side bending with stiffener

Cantilever moment in plate; mcc = fc  ((Bpc - ls)/2 - ts/2 - 0.8swsp)2/2 = ;106 Nmm/mm
Span moment in plate; mcs = abs(mcc - [0.6  fc  (ls - ts - 20.8swsp)2/8 = ;68 Nmm/mm
Design moment; mc = max(mcc, mcs) = 106 Nmm/mm
Plate thickness required; tpc = (4  mc/pyp) = 1.2 mm

Plate thickness
Plate thickness required; tp_req = tpc = ;1.2 mm;
Plate thickness provided; tp = 12 mm
PASS - Plate thickness provided is adequate (0.103)
Stiffener section classification for bending
Parameter ;  = (275 N/mm2 / pys)0.5 = 1.000
Ratio for section classification; R = ds2/ts = 31.3
Section classification (Table 11); Slender; (Using stem of T-section)
;
The stiffeners are slender and are therefore beyond the scope of the calculation

Shear transfer to concrete

Assumed coefficient of friction;  = 0.30
Available shear resistance; Pv = Cf   = ;2; kN
PASS - Frictional shear capacity is adequate (0.339)

Tension+moment with stiffeners example PULL-OUT CAPACITY OF HOLDING DOWN BOLTS

TEDDS calculation version 1.0.01
These calculations assume that there is no coexistent shear in the holding-down bolts.
Tension capacity of bolts
; Maximum tension force per bolt; Ft = 7.0 kN
; Try M16 (Grade 8.8); bolts; Pt = 70.7 kN ; dnut = 13 mm
Check Ft  Pt ; Pass - Bolt tension capacity;
 Project Job Ref.
JINJANGUTARA3
Section Sheet no./rev.
BOLT POLE 6
Calc. by Date Chk'd by Date App'd by Date
FATIN 13-Sep-21 ANWAR

Pull-out resistance of concrete

;; Overall length of bolts; Lbolt = 150 mm
; Clear projection of bolt above nut; Lproj = 8 mm
;;; Thickness of washer, baseplate & grout; twas = 22 mm ; tp = 6 mm ; tgr = 25 mm
Depth of embedment; de = Lbolt - Lproj - dnut - twas - tp - tgr = 76 mm
From BCSA HDBolts document, effective conical surface area; for two bolts; Aec = 515.4 cm2
Depth of embedment selected; de = 76 mm
Design spacing of bolts (c/c); Xccs = 210 mm
; Shear strength of concrete; vc = 0.34 N/mm2
Design pull-out resistance, per bolt; Ptc = Aec  vc / 2 = 8.8 kN
Check Ft  Ptc ; Pass - Concrete pull-out resistance
Bolts require adequate anchorage by suitably sized washer plates or equivalent under the bolt heads.
BS 5950: Part 1: 2000: Sections 4.13 & 6.6
'Holding down systems for steel stanchions' BCSA / Constrado 1980
;
DRAWING

Page 42
 COORDINATE
LATITUDE 3° 21' 63.9" N

LONGITUDE 101° 65' 88" E

FOURSONS
KUALA LUMPUR
23, JALAN BUKIT PERMAI UTAMA TIGA,
TAMAN BUKIT PERMAI,
PE DRAWING CENTRAL
56100 KUALA LUMPUR.
TEL NO: 03-42856433, FAX: 03-42856733
 S3

MAXIS CABIN

S2 S1

ROOF PLAN
SCALE NA

BUILDING FRONT VIEW

SCALE NA

BUILDING SIDE VIEW

SCALE NA

FOURSONS
KUALA LUMPUR
23, JALAN BUKIT PERMAI UTAMA TIGA,
TAMAN BUKIT PERMAI,
PE DRAWING CENTRAL
56100 KUALA LUMPUR.
TEL NO: 03-42856433, FAX: 03-42856733
 FOURSONS
KUALA LUMPUR
23, JALAN BUKIT PERMAI UTAMA TIGA,
TAMAN BUKIT PERMAI,
PE DRAWING CENTRAL
56100 KUALA LUMPUR.
TEL NO: 03-42856433, FAX: 03-42856733
 FOURSONS
KUALA LUMPUR
23, JALAN BUKIT PERMAI UTAMA TIGA,
TAMAN BUKIT PERMAI,
PE DRAWING CENTRAL
56100 KUALA LUMPUR.
TEL NO: 03-42856433, FAX: 03-42856733
 FOURSONS
KUALA LUMPUR
23, JALAN BUKIT PERMAI UTAMA TIGA,
TAMAN BUKIT PERMAI,
PE DRAWING CENTRAL
56100 KUALA LUMPUR.
TEL NO: 03-42856433, FAX: 03-42856733