OWNER´S MANUAL

1200.4
1
 TABLE OF CONTENTS

Introduction ................................................................................................................... 3

Package contents ...................................................................................................... 3

Safety instructions ...................................................................................................... 4

Technologies

DTR............................................................................................................. 5

Ultra Compact PCB.......................................................................... 5

Vibration Absorption Device......................................................... 6

Low Battery consumption............................................................. 6

Assembling and Disassembling the plastic cover................................... 7

Panels description

Audio inputs and controls............................................................ 8

Power inputs and audio outputs.............................................. 9

Electrical Dimensioning........................................................................................... 10

Audio inputs

RCA inputs............................................................................................ 10

High inputs............................................................................................ 10

Installation sequence................................................................................................. 11

Wiring diagram

Four channels wiring diagram................................................... 12

Three channels wiring diagram................................................ 12

Two channels wiring diagram.................................................... 13

Procedure for setting the gain.............................................................................. 13

Crossovers set up....................................................................................................... 14

Technical specs

Parameters......................................................................................... 15

Dimensional data............................................................................ 15

2
 INTRODUCTION

DEAR CUSTOMER,

CONGRATULATIONS ON ACQUIRING A PRODUCT WITH THE HIGHEST

QUALITY AND TECHNOLOGY!

You have just purchased a SounDigital product of the highest technology and
quality, so we thank you for your confidence.

SounDigital products are made with raw materials of the highest quality
standards, and the most modern processes, equipment and technology are used
in their production.

On this manual you will learn about the product, its features and characteristics, in
order to obtain the best result and to be able to enjoy your music with SounDigital
quality and power.

To better understand and take advantage of all the functions of the product and use
it safely, read this manual carefully and if you have any questions, consult our
support by email [email protected].

PACKAGE CONTENTS

- 1 EVOX Amplifier

- 1 Installation quick guide with warranty card

- 1 Allen wrench 2.0mm

- 1 Allen wrench 2.5mm

- 1 Allen wrench 3.0mm

- 2 Cables for high level input

- 1 Promotional sticker

3
 SAFETY INSTRUCTIONS

To prevent injuries to the user or damage to the amplifier, read all safety instructions
written on this manual;

If you are insecure about the installation of this equipment, get in touch with our
tech support or with a professional specialized in car audio installation;

Before proceeding with the installation of any electric equipment on your vehicle,
unplug the negative (-) terminal of the battery to avoid fires, injuries or damages;

Use your sound system safely. The continuous exposure to sound pressures over
85dB may cause irreversible hearing damage;

This equipment is for use in automotive DC voltage batteries between 12.6 and
14.4 volts. Before installing the equipment, check voltage of the batteries;

Do not install the amplifier in places exposed to water, dirt or humidity;

Choose a ventilated place to install the amplifier and avoid blocking the side
ventilation windows;

Mount the amplifier in a secure way. Avoid mounting it on metallic parts of the
vehicle, because it may cause ground looping (noise);

Make sure that the location chosen for the amplifier installation does not effect the
operation of the vehicle;

When passing cables through metallic walls, use rubber O-rings to avoid cable
cutting and short-circuits.

Clean the amplifier periodically with brush or dry cloth to assure the thermal
efficiency of the heatsink.

This product may reach temperatures over 60°C/140°F. Make sure it is cold before
touching it;

Be careful when making holes in the vehicle. Make sure you are not making holes
in the fuel tank, brake lines or electrical cables of the vehicle

Make sure the cables are properly secured throughout the installation;

Wear gloves, safety glasses and and all necessary PPE during the installation of
SounDigital amplifiers.

THIS "WARNING" SIGN ALERTS THE USER OF IMPORTANT INFO. NOT FOLLOWING
THIS INSTRUCTIONS MAY CAUSE INJURIES TO THE USER OR DAMAGE TO THE
EQUIPMENT.
Warning!

4
 TECHNOLOGIES

DYNAMIC THERMAL RECOVERY - DTR

ALUMINIUM
HEATSINK
CONDUCTIVE
COOPER LAYER

ELECTRONIC
COMPONENT

The DTR* is a dynamic thermal recovery system which always maintains a high
efficiency of the amplifier by accelerating the thermal exchange of electronic
components with the heatsink

* Patent. Required

ULTRA COMPACT PCB

An intelligent layout, with great use of the

PCB area and the use of modern
components with reduced structure
guarantee SounDigital products a
compact design, at the same time robust
and with excellent thermal efficiency.

5
 TECHNOLOGIES

VIBRATION ABSORPTION DEVICE

SounDigital added a new device to the EVO X products which act like shock
absorbers reducing the impact of vibration on the eletronic circuit board, thereby
increasing the life and reliability of the amplifiers.

I - POWER SUPPLY

SounDigital amplifiers are known for their low

consumption of battery, and this feature was
improved on the EVOX Line. The new I-
POWER SUPPLY is even more modern, which
replaces the old toroidal transformers by a new
generation of "E-E" core transformers delivers
efficiency above 90% *,ensuring more hours of
sound without battery recharge.

*Efficiency measured at power supply only

6
 ASSEMBLING AND DISASSEMBLING THE PLASTIC COVER

The plastic covers have the function of finishing and hiding the amplifier fixing
screws. To disassembling and assembling them, follow the instructions below.

DISASSEMBLING OF THE PLASTIC COVER

1 2

1. Carefully pull out the top of plastic cover to release the upside latches, as shown in the picture 1.
2. Slide up the plastic cover in a continuous movement to remove it.

ASSEMBLING THE PLASTIC COVER

1 2

EN
1. To fit the plastic cover back, carefully insert the point A of the plastic cover into point B of the
amplifier, slowly sliding it down.
2. Gently press the sides of the top of the plastic cover towards the bottom of the amplifier until
you hear a clicking noise.

7
 PANELS DESCRIPTION

9 5 8 10

1 2
13

3 4

11 6 7 12

1 CH1/CH2
Variable crossover control - 45Hz to 850Hz
2 CH3/CH4

3 CH1/CH2 High Level audio input

(To connect to the speaker output of the headunit)
4 CH3/CH4
5 CH1

6 CH2
Audio input - RCA connector
7 CH4

8 CH3

9 CH1/CH2 Crossover Switch

Low Pass - Full - High Pass
10 CH3/CH4

11 CH1/CH2
Variable Gain Control
12 CH3/CH4

13 - "Power ON" LED indicator (Blue)

8
 PANELS DESCRIPTION

18 20 22 24

17 19 21 23 16 15 14

14 - Negative power supply connector (GND)

15 - Remote power supply connector (REM)

16 - Positive power supply connector (+12VDC)

17 Positive speaker connector

CH1
18 Negative speaker connector

19 Negative speaker connector

CH2
20 Positive speaker connector

21 Negative speaker connector

CH3
22 Positive speaker connector

23 Positive speaker connector

CH4
24 Negative speaker connector

9
 ELECTRICAL DIMENSIONING AND AUDIO INPUTS

ELECTRICAL DIMENSIONING
For proper operation of your SounDigital amplifier, you need the proper
dimensioning of the electrical system and the cables used.

The table below shows the minimum section of GND cables, +12VDC cables and
speaker output cables according to the power generated by the amplifier.

POWER CABLE
1200 16mm² - 5 AWG
GROUND CABLE
WRMS
SPEAKER CABLE

We recommend the use of ONLY OFC (Oxygen Free Copper) Cables on the
installation of our products.

AUDIO INPUTS
RCA Inputs

All RCA Inputs must be connected for

the 4 channels to work.

High signal inputs

X All High signal Inputs must be connected for

the 4 channels to work.

High input must be used when the main unit does not have RCA outputs.

When hi inputs is used, no remote connection is required, the amplifier recognizes

the audio signal and switches on.

If your source unit is not able to turn on the amplifier through the high level input, the
remote input should be connected normally.

RCA AND HIGH INPUTS SHOULD NOT BE USED SIMULTANEOUSLY OR YOU MAY
DAMAGE THE AMPLIFIER.
Warning!

10
 INSTALLATION SEQUENCE

Warning!

Ø Mount the amplifier in such a way you have access to the connectors;

Ø Install the power cables in the vehicle properly, starting from the battery to the fuse
holder or circuit breaker, use the cable with the appropriate size. Make all connections,
install fuse holders or circuit breakers, but without placing the fuses or with the circuit
breakers in the "Off" position.

Warning!

Ø Connect the power cables in to the amplifier, observing the polarity. Connect all the
positive cables from the fuse holder or circuit breaker to the positive conector of the
amplifier and all the negative power cables from the batteries to the negative connector
of the amplifier;

Ø The ground cable must be as short as possible and must be connected to the vehicle
chassis and the battery negative;

Remove the paint between

the terminal and chassis

Ø Install the signal input cables in a proper way, distant from the power cables;

Ø Connect the RCA or the high signal input cables to the head unit and amplifiers;

Ø Install the audio output cables with the appropriate section , distant from the power and
audio input cables;

Ø Connect the audio output cables to the amplifier and speakers respecting the positive
(+) and negative (-) polarities;

Ø Install the remote cable with the power cables, using 1.5mm² (15 AWG) cable or thicker;

Ø Connect the remote power cable to the amplifier's "REM" terminal at the main unit's
remote power output (when not using the high level signal inputs);

Ø Before powering the system, verify all the connections and make sure there are no
mistakes or short-circuits on the power and ground cables;

Ø Reconnect the ground of the batteries;

Ø Check if the headunit is turned off and then place the fuses in the fuse holders or switch
the circuit breakers on;

Ø Turn on the main unit and the amplifier will turn on the "On" LED indicating that it is in
operation.

11
 WIRING DIAGRAM

4 CHANNEL WIRING DIAGRAM

See "Audio Inputs"

on page 10

GND

3 CHANNEL WIRING DIAGRAM

See "Audio Inputs"

on page 10

GND

12
 WIRING DIAGRAM / GAIN SETING

2 CHANNEL WIRING DIAGRAM

See "Audio Inputs"

on page 10

GND

GAIN SETING Ø Set the source unit's fader control to

center position;
Necessary equipament:
Ø Set the crossover selector switch in "F"
Ø Digital AC voltmeter;
Ø Use a 60 Hz sine wave
Ø Media with sine wave test tone 60Hz
recorded at 0db; Ø Connect the AC voltmeter to the
speaker output connectors of the
Ø Screwdriver 1/8" ( for gain set) amplifier. Make sure you test the
voltage at the correct connectors (+
Set up procedure and –);
Ø This procedure is the same for both
Ø Increase the gain control until the target
gain controls;
voltage is observed with the voltmeter
(see the chart below);
Ø Turn the gain control all the way down.
Ø Once you have adjusted the amplifier
Ø Disconnect the output cables from the to its correct voltage output, turn off the
amplifier outputs; source unit and reconnect the
speaker(s)
Ø Turn off all processing (bass, treble,
loudness, EQ, etc.); Download the tracks for set up in
https://soundigitalusa.com/tracks-for-
Ø Set the source unit volume to 3/4 of full set-up/
volume.

MODEL STEREO / POWER BRIDGE / POWER STEREO OUTPUT VOLTAGE BRIDGE OUTPUT VOLTAGE

1200.4 2Ω 1Ω/ 300W 2Ω/ 600W 17.3 V 34.6 V

1200.4 4Ω 2Ω/ 300W 4Ω/ 600W 24.5 V 49.0 V

13
 CROSSOVER SET UP

"F" All the frequencies are reproduced;

"LP " Set in the variable control on Low Pass Function;
"HP " Set in the variable control on High Pass Function.

Ø Switch Key to "F" position (Full Range): All the frequencies are reproduced.

dB

0dB

-12dB

Hz

Ø Switch key to "HP" - Set in the variable control between 45Hz and 850Hz ("A")
where you want to perform the high pass cut filter;

dB A

0dB
-3dB
-15dB

ƒc/2 ƒc
High High Hz
Pass Pass

Ø Switch key to "LP" - Set in the variable control between 45Hz and 850Hz ("B")
where you want to perform the low pass cut filter;

dB B

0dB
-3dB

-15dB

ƒc ƒc*2
Low Low Hz
Pass Pass

14
 TECHNICAL SPECS

PARAMETERS 1200.4 2Ω 1200.4 4Ω

Power RMS Bridge @ 4Ω* 2 X 396W 2 X 600W
Power RMS Bridge @ 2Ω* 2 X 600W N/A
Power RMS @ 2Ω* 4 X 198W 4 X 300W
Power RMS @ 1Ω* 4 X 300W N/A
Frequency Response (-3dB) 5Hz ~ 22kHz 5Hz ~ 22kHz
Low Pass filter (12dB/oct) 45Hz ~ 850Hz 45Hz ~ 850Hz
High Pass filter (12dB/oct) 45Hz ~ 850Hz 45Hz ~ 850Hz
Operating Voltage 8V ~ 16V 8V ~ 16V

SNR 91dB 91dB

Input Sensitivity 0.2 ~ 4V 0.2 ~ 4V
Current Draw (Music) 57A 58A
Current Draw (Max) 113A 116A
Total Efficiency 84% 82%
Damping Factor (@100Hz nominal impedance) 200 200
Stereo Minimum Impedance 1Ω 2Ω
Bridge Minimum Impedance 2Ω 4Ω
Fuse (music) 60A 60A
Recommended batery 70Ah 70Ah

*Power at 12.6V @ 60Hz with a maximum THD of 1%.

DIMENSIONAL DATA

7.1"(181mm)
2.2"(55mm)
5.4"(136")

Net Weight: 2.60 lb (1.18 kg)

Gross Weight: 2.95 lb (1.34 kg)

6.4"(162mm)
4.8"(121mm)

15
16