General Purpose Relays
Power Relays Potter & Brumfield
T90 Series, 30A PCB Relay
n 30A, 1 Form A (NO); 20A, 1 Form C (CO)
n Available as open frame or sealed construction
n Meets UL 508 and 873 Spacing - 3.18 through air, 6.36 over surface
n UL class F insulation system standard
Typical applications
HVAC, Appliances, Industrial Controls
Approvals Coil Data
UL E22575; CSA LR15734 Coil voltage range 5 to 110VDC
Technical data of approved types on request Max. coil power 1.0W
Max. coil temperature 155°C
Contact Data Coil insulation system according UL Class F
Contact arrangement 1 form A (NO), 1 form B (NC), 1 form C (CO)
Rated voltage 277VAC Coil versions, DC coil
Max. switching voltage 277VAC Coil Rated Operate Release Coil Rated coil
Rated current 30A code voltage voltage voltage resistance power
Limiting continuous current 30A VDC VDC VDC Ω±10% wW
Limiting making current 30A 5 5 3.75 0.5 27 900
Limiting breaking current 30A 6 6 4.5 0.6 40 900
Contact material AgCdO 9 9 6.75 0.9 97 900
Min. recommended contact load 1A, 5VDC or 12VAC 12 12 9 1.2 155 900
Initial contact resistance 75 mΩ at 1A at 5VDC or 12VAC 18 18 13.5 1.8 380 900
Frequency of operation, with load 360hr 24 24 18 2.4 660 900
Operate/release time max., including bounce 15/15ms 48 48 36 4.8 2560 900
110 110 82.5 11 13450 900
Contact ratings All figures are given for coil without preenergization, at ambient temperature +23°C.
Type Load Cycles
Typical Ambient temperature vs. coil voltage – 1W coil
130
AgCdO, open style relay
Coil Temp. Rise Above Ambient (°C)
Open Style Relay, No Dust Cover
120
NO 30A, 240VAC, general purpose 100x103
110
NO 20A, 240VAC, resistive heater 100x103 100
CO 20A/10A, 240VAC, general purpose 100x103 90
CO 20A/10A, 28VDC, resistive 100x103 80
UL 508/873 70
AgCdO 60 30A Load
NO 30A, 240VAC, general purpose 100x103 50 25A Load
NC 15A, 240VAC, general purpose 100x103 40 20A Load
15A Load
CO 20A/10A, 240VAC, general purpose 100x103 30 10A Load
0A Load
NO 20A, 240VAC, resistive 100x103 20
50 75 100 125 150 175 200 225
NC 15A, 240VAC, resistive 100x103 Applied Continuous Coil Voltage (% of Rated Voltage)
CO 20A/10A, 240VAC, resistive 100x103 150
140 Wash Tight Relay, Vented
NO 80LRA/30FLA, 240VAC 30x103
Coil Temp. Rise Above Ambient (°C)
130
NC 30LRA/10FLA, 240VAC 30x103
120
CO 53.6LRA/20FLA / 20LRA/6.7FLA, 240VAC 100x103 110
NO 98LRA/22FLA, 120VAC 100x103 100
NO 2HP, 240VAC 1x103 90
NC 1/2HP, 240VAC 1x103 80
NO 1HP, 120VAC 1x103 70 30A Load
NC 1/4HP, 120VAC 1x103 60
25A Load
50
NO 6A, 277VAC, ballast 100x103 20A Load
40
NC 3A, 277VAC, ballast 6x103 30
15A Load
10A Load
NO TV5, 240VAC, tungsten 6x103 20
0A Load
50 75 100 125 150 175 200 225
NC TV3, 240VAC, tungsten 6x103 Applied Continuous Coil Voltage (% of Rated Voltage)
NO 20A, 28VDC, resistive 100x103 Data graphed above are average values and should be verified in application. Tests were
NC 10A, 28VDC, resistive 100x103 conducted within a 2’ (.6m) cube (still air); at nominal coil power @ 25°C; with normally
All ratings at 25°C (unless otherwise noted) with relay properly vented. Remove vent nib open contact loaded; and with 4’ (1.22m) long, #10AWG load wires. P.C. board relays were
from enclosed relays after soldering and cleaning for optimum life. mounted to a 30A, single side P.C. board. Coil rise test conducted with a 30A PC board
to maintain 20°C max. rise at 30°C. The relay connections and wiring must be designed
with an adequate cross section to ensure proper current flow and heat dissipation. After
Mechanical endurance 10x106 ops. cleaning process knock-off nib should be removed for optimum life of wash-tight relays.
1
08-2011, Rev. 0811 Datasheets and product specification Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec-
www.te.com according to IEC 61810-1 and to be used terms of the disclaimer and all chapters of tion, application notes and all specifications
© 2011 Tyco Electronics Corporation, only together with the ‘Definitions’ section. the ‘Definitions’ section, available at are subject to change.
a TE Connectivity Ltd. company http://relays.te.com/definitions
General Purpose Relays
Power Relays Potter & Brumfield
T90 Series, 30A PCB Relay (Continued)
Insulation Data Other Data (continued)
Initial dielectric strength Vibration resistance (functional) 1.65mm max excursions, 10-55 Hz
between open contacts 1500Vrms Shock resistance (functional) 10g for 11msec
between contact and coil 1500Vrms Shock resistance (destructive) 100g
Initial insulation resistance Terminal type pcb-tht
between insulated elements 1x109Ω Weight 20g open relay
Clearance/creepage 26g wash-tight relay
between contact and coil 3.17mm Resistance to soldering heat THT
IEC 60068-2-20 250°C
Packaging/unit tray/50 pcs., box/500 pcs.
Other Data 1) Operating ambient temperature must consider “Must Operate Voltage Change Over
Material compliance: EU RoHS/ELV, China RoHS, REACH, Halogen content Temperature,” Contact Temperature Rise, Coil Temperature Rise (If coil is not allowed to
cool) and Maximum Coil Temperature. Specification ambient considers 20A load with
refer to the Product Compliance Support Center at coil cooled to ambient.
www.te.com/customersupport/rohssupportcenter
Ambient temperature
DC coil -55ºC to 85ºC 1)
Category of environmental protection
IEC 61810 RT0 - open, RTII - flux proof
Dimensions
T90N T90S
.031 x .062 .130 + .016
.680 MAX. (.79 x 1.58) .805 MAX. – .010 .212 MAX.
.950 MAX.
(24.13)
(17.27) TERMINALS (20.4) ( 3.30 + .41
–.25 ) (5.38)
.032 x .062
.130 .020
(3.3 .51) (.8 x 1.6)
TERMINALS
.50 .10 MAX.
1.20 MAX. .69 (12.8) (2.54)
(30.5) (17.6)
1.27 MAX.
(32.26)
.025 x .025
2x (.64 x .64)
.025 x .025 TERMINALS
(.64 x .64) .045 x .045
(1.14 x 1.14) 1.08 MAX. .016
TERMINALS (.43)
TERMINALS (27.43) .045 x .045
2x (1.14 x 1.14)
TERMINALS
Terminal assignment PCB layout
Bottom view on pins Bottom view on pins
.081 ± .005 DIA.
1 Form A 1 Form B 1 Form C (2.06 ± .13)
.078 ± .003 DIA.
.100 (1.98 ± .08)
.300 Only necessary terminals are
(7.62) (2.54)
present on single throw models
and terminal code 4 models.
Consequently, some holes will be
.600 .600 unnecessary for those models.
(15.24) (15.24)
.043 ± .003 DIA.
(1.09 ± .08)
.150 .350
Note: This terminal is not present on relays with terminal code 4. (3.81) (8.89)
.550
(13.97)
.700
(17.78)
Accessory
35C620A
Optional plastic dust cover is a snap-on unit, open on the PC board side of
the relay. The cover, when ordered with the relay, is shipped separately. It is
.719 1.067 MAX.
designed to be snapped into place by the customer after the relay has been (18.26) (27.1)
assembled to the PC board.
.50
.69 (12.7)
Product Code Description Part Number (17.5)
35C620A Black dust cover, for use on T90N relay 4-1393209-2
1.256 MAX.
(31.9)
.090
(2.29) .87
(22.1)
2
08-2011, Rev. 0811 Datasheets and product specification Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec-
www.te.com according to IEC 61810-1 and to be used terms of the disclaimer and all chapters of tion, application notes and all specifications
© 2011 Tyco Electronics Corporation, only together with the ‘Definitions’ section. the ‘Definitions’ section, available at are subject to change.
a TE Connectivity Ltd. company http://relays.te.com/definitions
General Purpose Relays
Power Relays Potter & Brumfield
T90 Series, 30A PCB Relay (Continued)
Product code structure Typical product code T90 S 5 D 1 2 -24
Type
T90 Power PCB relay T90
Enclosure
N Open, no enclosure (snap-on dust cover available as an option)
S Wash-tight, sealed plastic case with knock off nib for ventilation
Contact arrangement
1 1 form A (1 NO) 2 1 form B (1 NC) 5 1 form C (1 CO)
Coil Input
D DC voltage
Mounting and termination
1 PCB terminals
4 PCB terminals, no common terminal between coil terminals (see pcb layout/terminal assignment drawing)
Note: Terminal code 4 recommended for UL 873 applications. Consult factory for use of terminal code 1 for UL 873 applications.
Contact material
2 AgCdO
Coil voltage
Coil code: please refer to coil versions table
Product Code Enclosure Contacts Terminals Contact Material Coil Part Number
T90N1D12-5 open, no cover 1 form A, 1 NO pcb AgCdO 5 VDC 7-1393208-4
T90N1D12-9 9 VDC 7-1393208-5
T90N1D12-12 12 VDC 6-1393208-5
T90N1D12-18 18 VDC 6-1393208-8
T90N1D12-24 24 VDC 7-1393208-0
T90N1D12-48 48 VDC 7-1393208-3
T90N1D12-110 110 VDC 6-1393208-4
T90N1D42-12 pcb, no extra COM 12 VDC 7-1393208-7
T90N1D42-24 24 VDC 7-1393208-9
T90N5D12-5 1 form C, 1 CO pcb 5 VDC 9-1393208-5
T90N5D12-12 12 VDC 8-1393208-6
T90N5D12-18 18 VDC 9-1393208-0
T90N5D12-24 24 VDC 9-1393208-3
T90N5D12-48 48 VDC 9-1393208-4
T90N5D12-110 110 VDC 8-1393208-5
T90N5D42-12 pcb, no extra COM 12VDC 9-1393208-9
T90N5D42-24 24 VDC 1393209-2
T90S1D12-5 wash tight 1 form A, 1 NO pcb 5 VDC 1-1393209-8
T90S1D12-6 6 VDC 1-1393209-9
T90S1D12-9 9 VDC 2-1393209-0
T90S1D12-12 12 VDC 1-1393209-2
T90S1D12-18 18 VDC 1-1393209-3
T90S1D12-24 24 VDC 1-1393209-6
T90S1D42-12 pcb, no extra COM 12 VDC 2-1393209-2
T90S1D42-24 24 VDC 2-1393209-5
T90S1D42-48 48 VDC 2-1393209-6
T90S5D12-5 1 form C, 1 CO pcb 5 VDC 3-1393209-4
T90S5D12-12 12 VDC 2-1393209-8
T90S5D12-18 18 VDC 3-1393209-0
T90S5D12-24 24 VDC 3-1393209-1
T90S5D12-48 48 VDC 3-1393209-3
T90S5D42-12 pcb, no extra COM 12 VDC 1423094-1
T90S5D42-18 18 VDC 3-1393209-8
T90S5D42-24 24 VDC 4-1393209-0
3
08-2011, Rev. 0811 Datasheets and product specification Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec-
www.te.com according to IEC 61810-1 and to be used terms of the disclaimer and all chapters of tion, application notes and all specifications
© 2011 Tyco Electronics Corporation, only together with the ‘Definitions’ section. the ‘Definitions’ section, available at are subject to change.
a TE Connectivity Ltd. company http://relays.te.com/definitions
