Corporate Office: 3281 E.
Guasti Road, Suite 260, Ontario, CA, 91761 USA
Sales Office: 11201 Jersey Blvd, Rancho Cucamonga, CA, 91730 USA
T: (909) 987-0550 • (800) 538-3091 • F: (909) 605-6111
www.pacertechnology.com
Pacer Technology’s RX Series Range Extended cyanoacrylate adhesives are a family of non-surface sensitive
adhesives for porous, acidic, contaminated, or hard-to-bond substrates, such as certain plastics and plated
surfaces. Viscosities range from water-thin to a non-running gel to fit a variety of application requirements.
PROPERTIES:
Liquid State RX-5 RX-50 RX-100 RX-500 RX-700 RX-GEL
Base Chemical Ethyl Hybrid Cyanoacrylate
Color Translucent Liquid
Viscosity, cP 2-10 30-70 80-120 350-550 600-800 20,000 -50,000
Flashpoint, F (C) 185 (85) 185 (85) 185 (85) 185 (85) 185 (85) 185 (85)
Vapor Pressure
8 8 8 8 8 8
(mmHg @ 70C)
Specific Gravity (@25F) 1.04 1.06 1.07 1.08 1.08 1.12
Soluble in: Acetone, MEK
Cured State RX-5 RX-50 RX-100 RX-500 RX-700 RX-GEL
Temperature Range -65F to +180 F (-54C to 82C)
Hardness, Rockwell (M) 75 74 74 74 74 74
Outgassing
0 0 0 0 0 0
(@ 10-6 mmHg, 72F)
Typical Gap, inches 0.002 0.004 0.005 0.008 0.010 0.020
311 306 306 306 306 303
Softening Point, F (C)
(155) (152) (152) (152) (152) (151)
365 365 365 365 365 365
Melting Point, F (C)
(185) (185) (185) (185) (185) (187)
347 347 347 347 347 347
Glass Transition, F (C)
(175) (175) (175) (175) (175) (175)
Soluble in: X-9 Debonder, Acetone, Nitropropane
Shear Strength, psi ASTM D-1002
2300 2300 2300 2300 2300 2400
Steel
(±10%) (±10%) (±10%) (±10%) (±10%) (±10%)
1600 1600 1600 1600 1600 1600
Aluminum
(±10%) (±10%) (±10%) (±10%) (±10%) (±10%)
1400 1400 1400 1400 1400 1400
Copper
(±10%) (±10%) (±10%) (±10%) (±10%) (±10%)
ABS SF* SF* SF* SF* SF* SF*
Rigid PVC SF* SF* SF* SF* SF* SF*
Page 1 of 3
Nylon SF* SF* SF* SF* SF* SF*
Polycarbonate SF* SF* SF* SF* SF* SF*
SBR SF* SF* SF* SF* SF* SF*
EPDM SF* SF* SF* SF* SF* SF*
Tensile Strength, psi
4000 4000 4000 4000 4000 4000
Steel (ASTM D-2095)
(±10%) (±10%) (±10%) (±10%) (±10%) (±10%)
Dielectric Constant
3.98 3.98 3.98 3.98 3.98 3.98
(1MC)
Volume Resistivity
8.4x1012 8.4x1012 8.4x1012 8.4x1012 8.4x1012 8.4x1012
(ohm-cm)
*Substrate failure
APPLICATION AND CURE CHARACTERISTICS:
For best results, parts should be clean, free from oil and grease or other contaminants. Apply adhesive to
one surface to be bonded and mate the other surface to it carefully without delay. For best results, use a
minimal amount of adhesive. In general, one free-falling drop covers one square inch of bond area. Avoid
over-application, as excess adhesive is difficult to remove from unwanted areas.
Fixture time occurs in 1-5 minutes with 80% of full strength developing in 15-30 minutes. Fixture time and
full cure rates are dependent upon temperature, relative humidity, bondline thickness, and substrates being
bonded.
To speed full cure through larger gaps, Pacer accelerators for instant adhesives are compatible and can be
used. Post application of accelerators to exposed adhesive may cause a white frosting (chlorosis) of the
exposed adhesive onto parts, which can usually be removed using Pacer X-9 Debonder and a cotton swab.
Overall cure strength can be decreased as a result of using accelerators. Testing on actual parts is
recommended.
STORAGE AND SHELF LIFE:
Refrigerate unopened cyanoacrylate for optimal results. Once opened, store in a cool, dry location away
from heat sources. Stored under these conditions, a one-year shelf life can be expected.
APPROVALS:
Pacer Technology will certify compliance for the following:
Specification Compliance RX-5 RX-50 RX-100 RX-500 RX-700 RX-GEL
MIL-A-46050C (Type/Class) II/1 II/1 II/2 II/3 II/3 -
A-A-3097 (Commercial Spec) II/1 II/1 II/2 II/3 II/3 II/5
Page 2 of 3
SAFETY AND HANDLING PRECAUTIONS:
Cyanoacrylate adhesives bond skin in seconds. In case of skin contact, flush with water. If skin becomes
bonded, peel (do not pull) apart after immersion in warm, soapy water. In case of eye or mouth contact,
flush with water and get immediate medical attention.
Use with adequate ventilation. Vapors can irritate eyes and mucous membranes. Symptoms disappear after
removal of individual from vapors. Avoid contact with clothing as it can cause burns. For more information,
refer to the Safety Data Sheet available upon request or from our website at: http://www.supergluecorp.com
In case of emergency, call CHEMTREC at (800) 424-9300 or call Pacer Technology (800) 637-9803
(outside CA only) or (909) 987-0550.
Part Numbers:
REV 7 - KSR 2017
The information in this Product Data Sheet (PDS) is of a general nature based on our knowledge and
experience with this product and should be used for information and consideration purposes only. The
product can have a variety of different applications, as well as differing application and working conditions
in your environment that are beyond our control. Therefore, this data does not constitute a warranty,
expressed or implied, statutory or otherwise, nor is it representation for which Pacer Technology assumes
legal responsibility.
Pacer Technology strongly recommends that users of the product independently determine the suitability of
the product for their use. Pacer Technology specifically disclaims any liability for consequential or
incidental damages of any kind, including profit. Any use of this product must be determined by the user to
be in accordance with applicable federal, state, provincial, and local laws and regulations.
Page 3 of 3
