3/25/24, 3:54 PM SIS 2.

Fuel Transfer Pump - Assemble (SENR1126-36)

SMCS - 1256 i02044203

Assembly Procedure
PSP
202 -000A
Table 1

07: 4/03/2 4FC7

Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group
5
SEN 4:19+ 5
1

Note: Check the O-ring seals, gaskets, and the seals for wear or for damage. Replace the
components, if necessary.
© 2 R112 08:00
024 6
NOTICE
Cat
erp
Keep all parts clean from contaminants.

illa
Contaminants may cause rapid wear and shortened component
life.
r In
c.

Illustration 1 g01049857

1. Inspect bearings (19) in bracket (16). If the bearings are damaged, the bracket must be
replaced. The bearings are nonserviceable.

https://sis2.cat.com/#/print-preview/service/3664e67f-4dfc-4b12-9dbd-e0140343739b 1/5
3/25/24, 3:54 PM SIS 2.0

Illustration 2 g01049858
2. Coat the lip seals for bracket (16) with clean engine oil. Use Tooling (A) to install inner lip seal
(18) and outer lip seal (17) in the bracket. Make sure that the lips of the seals are oriented
properly.

Illustration 3 g01049863

3. Install sleeves (15) in bracket (16). Install O-ring seal (20) in casing (14). Place the casing over
the sleeves on the bracket.

Illustration 4 g00918557

https://sis2.cat.com/#/print-preview/service/3664e67f-4dfc-4b12-9dbd-e0140343739b 2/5
3/25/24, 3:54 PM SIS 2.0

4. Install idler gear (12) and drive shaft (13) into casing (14) and the bracket.

Illustration 5 g01049868

5. Inspect bearings (21) in plate (9). If the bearings are damaged, the plate must be replaced. The
bearings are nonserviceable.

Illustration 6 g01049930

6. Install O-ring seal (22) in plate (9). Place the plate into position on the casing.

https://sis2.cat.com/#/print-preview/service/3664e67f-4dfc-4b12-9dbd-e0140343739b 3/5
3/25/24, 3:54 PM SIS 2.0
Illustration 7 g01049933
7. Before you install the check valve in head (8), make sure that the spring on the check valve is
oriented toward the inside. Use Tooling (A) to install the check valve in the head. Install the
check valve so that the valve contacts the shoulder in the bore.

Illustration 8 g01049937

8. Before you install head (8), be sure that the weep hole is clear. Place gasket (11) and head (8)
in position on the plate. Install the bolts that hold the fuel transfer pump together.

Illustration 9 g00918545

Improper assembly of parts that are spring loaded can cause

bodily injury.

To prevent possible injury, follow the established assembly

procedure and wear protective equipment.

https://sis2.cat.com/#/print-preview/service/3664e67f-4dfc-4b12-9dbd-e0140343739b 4/5
3/25/24, 3:54 PM SIS 2.0

9. Install the following parts into the bracket: valve poppet (3), valve spring (4), washer (5) and
cap (6).

Illustration 10 g00918544

10. Coat O-ring seal (1) with clean engine oil. Install the O-ring seal. Install drive coupling (2) onto
the drive shaft.

End By:

a. Install the fuel transfer pump. Refer to Disassembly and Assembly, "Fuel Transfer Pump -
Install".

PSP-000A4FC7
2024/03/25
07:54:13+08:00
i01794560
© 2024 Caterpillar Inc.

https://sis2.cat.com/#/print-preview/service/3664e67f-4dfc-4b12-9dbd-e0140343739b 5/5