H310M M.2 2.

User's Manual
Rev. 1201

GIGABYTE will reduce paper use in order to fulfill the responsibilities of a global citizen.
Also, to reduce the impacts on global warming, the packaging materials of this product
are recyclable and reusable. GIGABYTE works with you to protect the environment.
For more product details, please visit GIGABYTE's website.
Copyright
© 2023 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer
Information in this manual is protected by copyright laws and is the property of GIGABYTE.
Changes to the specifications and features in this manual may be made by GIGABYTE without
prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or
published in any form or by any means without GIGABYTE's prior written permission.
„„ For detailed product information, carefully read the User's Manual.
„„ For quick set-up of the product, refer to the Quick Installation Guide on GIGABYTE's
website.
https://download.gigabyte.com/FileList/Manual/mb_manual_installation-guide_103.pdf?m=sw

For product-related information, check on our website at: https://www.gigabyte.com

Identifying Your Motherboard Revision

The revision number on your motherboard looks like this: "REV: X.X." For example, "REV: 1.0"
means the revision of the motherboard is 1.0. Check your motherboard revision before updating
motherboard BIOS, drivers, or when looking for technical information.

Example:
 Table of Contents
Chapter 1 Product Introduction........................................................................................4
1-1 Motherboard Layout.......................................................................................... 4

Chapter 2 Hardware Installation......................................................................................5

2-1 Installation Precautions..................................................................................... 5
2-2 Product Specifications....................................................................................... 6
2-3 Installing the CPU............................................................................................. 9
2-4 Installing the Memory...................................................................................... 10
2-5 Installing an Expansion Card.......................................................................... 10
2-6 Back Panel Connectors................................................................................... 11
2-7 Internal Connectors......................................................................................... 13

Chapter 3 BIOS Setup...................................................................................................20

3-1 Startup Screen................................................................................................ 20
3-2 The Main Menu............................................................................................... 21
3-3 M.I.T................................................................................................................ 22
3-4 System............................................................................................................ 28
3-5 BIOS................................................................................................................ 29
3-6 Peripherals...................................................................................................... 32
3-7 Chipset............................................................................................................ 35
3-8 Power.............................................................................................................. 36
3-9 Save & Exit...................................................................................................... 38

Chapter 4 Drivers Installation.........................................................................................39

Regulatory Notices..................................................................................................... 40
Contact Us................................................................................................................. 41

-3-
Chapter 1 Product Introduction
1-1 Motherboard Layout

CPU_FAN
KB_MS_USB

ATX_12V

ATX
SYS_FAN
VGA

LGA1151

HDMI

R_USB30

SATA3
3 2
1 0
USB_LAN
H310M M.2 2.0
80 60 42
F_USB30

AUDIO
M2A

DDR4_1

DDR4_2

Realtek® PCIEX16
GbE LAN

PCIEX1_1
BAT
iTE®
Super I/O
Intel® H310
PCIEX1_2
CODEC
M_BIOS

F_AUDIO TPM F_USB F_PANEL

CLR_CMOS

-4-
Chapter 2 Hardware Installation
2-1 Installation Precautions
The motherboard contains numerous delicate electronic circuits and components which can become
damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user's
manual and follow these procedures:
•• Prior to installation, make sure the chassis is suitable for the motherboard.
•• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or
warranty sticker provided by your dealer. These stickers are required for warranty validation.
•• Always remove the AC power by unplugging the power cord from the power outlet before
installing or removing the motherboard or other hardware components.
•• When connecting hardware components to the internal connectors on the motherboard, make
sure they are connected tightly and securely.
•• When handling the motherboard, avoid touching any metal leads or connectors.
•• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic
components such as a motherboard, CPU or memory. If you do not have an ESD wrist strap,
keep your hands dry and first touch a metal object to eliminate static electricity.
•• Prior to installing the motherboard, please have it on top of an antistatic pad or within an
electrostatic shielding container.
•• Before connecting or unplugging the power supply cable from the motherboard, make sure
the power supply has been turned off.
•• Before turning on the power, make sure the power supply voltage has been set according to
the local voltage standard.
•• Before using the product, please verify that all cables and power connectors of your hardware
components are connected.
•• To prevent damage to the motherboard, do not allow screws to come in contact with the
motherboard circuit or its components.
•• Make sure there are no leftover screws or metal components placed on the motherboard or
within the computer casing.
•• Do not place the computer system on an uneven surface.
•• Do not place the computer system in a high-temperature or wet environment.
•• Turning on the computer power during the installation process can lead to damage to system
components as well as physical harm to the user.
•• If you are uncertain about any installation steps or have a problem related to the use of the
product, please consult a certified computer technician.
•• If you use an adapter, extension power cable, or power strip, ensure to consult with its installation
and/or grounding instructions.

-5-
2-2 Product Specifications
CPU ŠŠ Support for 9th and 8th Generation
Intel® Core™ i9 processors/Intel® Core™ i7 processors/Intel® Core™ i5 processors/
Intel® Core™ i3 processors/Intel® Pentium® processors/
Intel® Celeron® processors in the LGA1151 package
(Go to GIGABYTE's website for the latest CPU support list.)
ŠŠ L3 cache varies with CPU
Chipset ŠŠ Intel® H310 Express Chipset
MEMORY ŠŠ 2 x DDR4 DIMM sockets supporting up to 32 GB of system memory
ŠŠ Dual channel memory architecture
ŠŠ Support for DDR4 2666/2400/2133 MHz memory modules
ŠŠ Support for ECC Un-buffered DIMM 1Rx8/2Rx8 memory modules (operate in
non-ECC mode)
ŠŠ Support for non-ECC Un-buffered DIMM 1Rx8/2Rx8/1Rx16 memory modules
ŠŠ Support for Extreme Memory Profile (XMP) memory modules
* To support 2666 MHz or XMP memory, you must install a 9th or 8th Generation Intel®
Core™ i9/i7/i5 processor.
(Go to GIGABYTE's website for the latest supported memory speeds and memory
modules.)
Onboard ŠŠ Integrated Graphics Processor-Intel® HD Graphics support:
Graphics - 1 x D-Sub port, supporting a maximum resolution of 1920x1200@60 Hz
- 1 x HDMI port, supporting a maximum resolution of 4096x2160@30 Hz
* Support for HDMI 1.4 version and HDCP 2.2.
ŠŠ Maximum shared memory of 1 GB
Audio ŠŠ Realtek® Audio CODEC
ŠŠ High Definition Audio
ŠŠ 2/4/5.1/7.1-channel
* You can change the functionality of an audio jack using the audio software. To
configure 7.1-channel audio, access the audio software for audio settings.

LAN ŠŠ Realtek® GbE LAN chip (1 Gbps/100 Mbps/10 Mbps)

Expansion Slots ŠŠ 1 x PCI Express x16 slot, running at x16
(The PCIEX16 slot conforms to PCI Express 3.0 standard.)
ŠŠ 2 x PCI Express x1 slots
(The PCI Express x1 slots conform to PCI Express 2.0 standard.)
Storage Interface ŠŠ Chipset:
- 1 x M.2 connector (Socket 3, M key, type 2242/2260/2280 SATA and PCIe
x2 SSD support)
- 4 x SATA 6Gb/s connectors
USB ŠŠ Chipset:
- 4 x USB 3.1 Gen 1 ports (2 ports on the back panel, 2 ports available through
the internal USB header)
- 6 x USB 2.0/1.1 ports (4 ports on the back panel, 2 ports available through
the internal USB header)

-6-
Internal ŠŠ 1 x 24-pin ATX main power connector
Connectors ŠŠ 1 x 4-pin ATX 12V power connector
ŠŠ 1 x M.2 Socket 3 connector
ŠŠ 4 x SATA 6Gb/s connectors
ŠŠ 1 x CPU fan header
ŠŠ 1 x system fan header
ŠŠ 1 x front panel header
ŠŠ 1 x front panel audio header
ŠŠ 1 x USB 3.1 Gen 1 header
ŠŠ 1 x USB 2.0/1.1 header
ŠŠ 1 x Trusted Platform Module (TPM) header (2x6 pin, for the GC-TPM2.0_S
module only)
ŠŠ 1 x Clear CMOS jumper
Back Panel ŠŠ 1 x PS/2 keyboard/mouse port
Connectors ŠŠ 1 x D-Sub port
ŠŠ 1 x HDMI port
ŠŠ 2 x USB 3.1 Gen 1 ports
ŠŠ 4 x USB 2.0/1.1 ports
ŠŠ 1 x RJ-45 port
ŠŠ 3 x audio jacks
I/O Controller ŠŠ iTE® I/O Controller Chip
Hardware ŠŠ Voltage detection
Monitor ŠŠ Temperature detection
ŠŠ Fan speed detection
ŠŠ Overheating warning
ŠŠ Fan fail warning
ŠŠ Fan speed control
* Whether the fan speed control function is supported will depend on the fan you install.
BIOS ŠŠ 1 x 128 Mbit flash
ŠŠ Use of licensed AMI UEFI BIOS
ŠŠ PnP 1.0a, DMI 2.7, WfM 2.0, SM BIOS 2.7, ACPI 5.0
Unique Features ŠŠ Support for APP Center
* Available applications in APP Center may vary by motherboard model. Supported
functions of each application may also vary depending on motherboard specifications.
- @BIOS
- EasyTune
- Smart Backup
- System Information Viewer
ŠŠ Support for Q-Flash
ŠŠ Support for Xpress Install

-7-
 Bundled ŠŠ Norton® Internet Security (OEM version)
Software ŠŠ LAN bandwidth management software
Operating ŠŠ Support for Windows 11 64-bit
System ŠŠ Support for Windows 10 64-bit
Form Factor ŠŠ Micro ATX Form Factor; 22.6cm x 17.4cm

* GIGABYTE reserves the right to make any changes to the product specifications and product-related information without
prior notice.

&& Please visit the SERVICE/SUPPORT\Utility page on GIGABYTE's website to download the latest version
of apps.
https://www.gigabyte.com/Support/Utility/Motherboard?m=ut

-8-
 2-3 Installing the CPU
Read the following guidelines before you begin to install the CPU:
•• Make sure that the motherboard supports the CPU.
(Go to GIGABYTE's website for the latest CPU support list.)
•• Always turn off the computer and unplug the power cord from the power outlet before installing the
CPU to prevent hardware damage.
•• Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may
locate the notches on both sides of the CPU and alignment keys on the CPU socket.)
•• Apply an even and thin layer of thermal grease on the surface of the CPU.
•• Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and damage
of the CPU may occur.
•• Set the CPU host frequency in accordance with the CPU specifications. It is not recommended
that the system bus frequency be set beyond hardware specifications since it does not meet the
standard requirements for the peripherals. If you wish to set the frequency beyond the standard
specifications, please do so according to your hardware specifications including the CPU, graphics
card, memory, hard drive, etc.

Installing the CPU

Locate the alignment keys on the motherboard CPU socket and the notches on the CPU.

LGA1151 CPU Socket LGA1151 CPU

Notch Notch
Alignment Key Alignment Key

Pin One Corner of the CPU Socket Triangle Pin One Marking on the CPU

Do not remove the CPU socket cover before inserting the CPU. It may pop off from the load
plate automatically during the process of re-engaging the lever after you insert the CPU.

&& Please visit GIGABYTE's website for details on hardware installation.

https://www.gigabyte.com/WebPage/210/quick-guide.html?m=sw

-9-
2-4 Installing the Memory
Read the following guidelines before you begin to install the memory:
•• Make sure that the motherboard supports the memory. It is recommended that memory of the same
capacity, brand, speed, and chips be used.
(Go to GIGABYTE's website for the latest supported memory speeds and memory modules.)
•• Always turn off the computer and unplug the power cord from the power outlet before installing the
memory to prevent hardware damage.
•• Memory modules have a foolproof design. A memory module can be installed in only one direction.
If you are unable to insert the memory, switch the direction.
Dual Channel Memory Configuration
This motherboard provides two memory sockets and supports Dual Channel Technology. After the memory
is installed, the BIOS will automatically detect the specifications and capacity of the memory. Enabling Dual
Channel memory mode will double the original memory bandwidth.
The two DDR4 memory sockets are divided into two channels and each channel has one memory socket as
following:

Channel A: DDR4_1

Channel B: DDR4_2
Due to CPU limitations, read the following guidelines before installing the memory in Dual Channel mode.
1. Dual Channel mode cannot be enabled if only one memory module is installed.
2. When enabling Dual Channel mode with two memory modules, it is recommended that memory of
the same capacity, brand, speed, and chips be used.

2-5 Installing an Expansion Card

Read the following guidelines before you begin to install an expansion card:
•• Make sure the motherboard supports the expansion card. Carefully read the manual that came
with your expansion card.
•• Always turn off the computer and unplug the power cord from the power outlet before installing an
expansion card to prevent hardware damage.

- 10 -
2-6 Back Panel Connectors

USB 2.0/1.1 Port

The USB port supports the USB 2.0/1.1 specification. Use this port for USB devices.
PS/2 Keyboard/Mouse Port
Use this port to connect a PS/2 mouse or keyboard.
D-Sub Port
The D-Sub port supports a 15-pin D-Sub connector and supports a maximum resolution of 1920x1200@60 Hz
(the actual resolutions supported depend on the monitor being used). Connect a monitor that supports
D-Sub connection to this port.
HDMI Port
The HDMI port supports HDCP 2.2 and Dolby TrueHD and DTS HD Master
Audio formats. It also supports up to 192KHz/16bit 8-channel LPCM audio
output. You can use this port to connect your HDMI-supported monitor. The maximum supported
resolution is 4096x2160@30 Hz, but the actual resolutions supported are dependent on the monitor
being used.
After installing the HDMI device, make sure to set the default sound playback device to HDMI. (The
item name may differ depending on your operating system.)

USB 3.1 Gen 1 Port

The USB 3.1 Gen 1 port supports the USB 3.2 Gen 1 specification and is compatible to the USB 2.0
specification. Use this port for USB devices.
RJ-45 LAN Port
The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following
describes the states of the LAN port LEDs.
Speed LED Activity LED Speed LED: Activity LED:
State Description State Description
Orange 1 Gbps data rate FLASH Data transmission or receiving is occurring
Green 100 Mbps data rate Off No data transmission or receiving is occurring
Off 10 Mbps data rate
LAN Port

•• When removing the cable connected to a back panel connector, first remove the cable from your
device and then remove it from the motherboard.
•• When removing the cable, pull it straight out from the connector. Do not rock it side to side to
prevent an electrical short inside the cable connector.
- 11 -
Line In/Rear Speaker Out (Blue)
The line in jack.
Line Out/Front Speaker Out (Green)
The line out jack. Use this audio jack for a headphone or 2-channel speaker.
Mic In/Center/Subwoofer Speaker Out (Pink)
The Mic in jack.
Audio Jack Configurations:
Headphone/
Jack 4-channel 5.1-channel 7.1-channel
2-channel
Line In/Rear Speaker Out a a a
Line Out/Front Speaker Out a a a a
Mic In/Center/Subwoofer Speaker Out a a
Front Panel Line Out/Side Speaker Out a

You can change the functionality of an audio jack using the audio software. To configure
7.1-channel audio, access the audio software for audio settings.
&& Please visit GIGABYTE's website for details on configuring the audio software.
https://www.gigabyte.com/WebPage/697/realtek897-audio.html

- 12 -
2-7 Internal Connectors
4 1 3

13
8

12

11

7 10 9 6

1) ATX_12V 8) F_USB30
2) ATX 9) F_USB
3) CPU_FAN 10) TPM
4) SYS_FAN 11) CLR_CMOS
5) SATA3 0/1/2/3 12) BAT
6) F_PANEL 13) M2A
7) F_AUDIO

Read the following guidelines before connecting external devices:

•• First make sure your devices are compliant with the connectors you wish to connect.
•• Before installing the devices, be sure to turn off the devices and your computer. Unplug the power
cord from the power outlet to prevent damage to the devices.
•• After installing the device and before turning on the computer, make sure the device cable has
been securely attached to the connector on the motherboard.
- 13 -
1/2) ATX_12V/ATX (2x2 12V Power Connector and 2x12 Main Power Connector)
With the use of the power connector, the power supply can supply enough stable power to all the components
on the motherboard. Before connecting the power connector, first make sure the power supply is turned
off and all devices are properly installed. The power connector possesses a foolproof design. Connect the
power supply cable to the power connector in the correct orientation.
The 12V power connector mainly supplies power to the CPU. If the 12V power connector is not connected,
the computer will not start.
To meet expansion requirements, it is recommended that a power supply that can withstand high
power consumption be used (500W or greater). If a power supply is used that does not provide the
required power, the result can lead to an unstable or unbootable system.

ATX_12V:
Pin No. Definition
3 4
1 GND
1 2 2 GND
3 +12V
ATX_12V
4 +12V

ATX:

12 24 Pin No. Definition Pin No. Definition

1 3.3V 13 3.3V
2 3.3V 14 -12V
3 GND 15 GND
4 +5V 16 PS_ON (soft On/Off)
5 GND 17 GND
6 +5V 18 GND
7 GND 19 GND
8 Power Good 20 NC
9 5VSB (stand by +5V) 21 +5V
10 +12V 22 +5V
11 +12V (Only for 2x12-pin 23 +5V (Only for 2x12-pin ATX)
1 13 ATX)
12 3.3V (Only for 2x12-pin 24 GND (Only for 2x12-pin ATX)
ATX)
ATX

- 14 -
3/4) CPU_FAN/SYS_FAN (Fan Headers)
All fan headers on this motherboard are 4-pin. Most fan headers possess a foolproof insertion design.
When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is
the ground wire). The speed control function requires the use of a fan with fan speed control design. For
optimum heat dissipation, it is recommended that a system fan be installed inside the chassis.

Pin No. Definition

1 GND
1
2 Voltage Speed Control
CPU_FAN 1 3 Sense
SYS_FAN 4 PWM Speed Control

•• Be sure to connect fan cables to the fan headers to prevent your CPU and system from
overheating. Overheating may result in damage to the CPU or the system may hang.
•• These fan headers are not configuration jumper blocks. Do not place a jumper cap on the headers.

5) SATA3 0/1/2/3 (SATA 6Gb/s Connectors)

The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA
1.5Gb/s standard. Each SATA connector supports a single SATA device.

7 7
Pin No. Definition
1 GND
2 TXP
SATA3
3 TXN
3 2
4 GND
1 0
5 RXN
6 RXP
7 GND
1 1

To enable hot-plugging for the SATA ports, refer to Chapter 2, "BIOS Setup," "Peripherals\SATA
And RST Configuration," for more information.

- 15 -
6) F_PANEL (Front Panel Header)
Connect the power switch, reset switch, speaker, chassis intrusion switch/sensor and system status indicator
on the chassis to this header according to the pin assignments below. Note the positive and negative pins
before connecting the cables.

Power LED Power Switch Speaker •• PLED/PWR_LED (Power LED):

System Status LED Connects to the power status indicator
S0 On on the chassis front panel. The LED is on
PLED+

PW+

when the system is operating. The LED is

SPEAK+

SPEAK- S3/S4/S5 Off

PLED-

G.QBOFM
PW-

off when the system is in S3/S4 sleep state

NC
NC

2 20 or powered off (S5).

1 19 •• PW (Power Switch):
Connects to the power switch on the chassis front panel. You may
PWR_LED+
HD-

CI+
RES+

PWR_LED-
PWR_LED-

configure the way to turn off your system using the power switch (refer
-IC
HD+

RES-

to Chapter 2, "BIOS Setup," "Power," for more information).

•• SPEAK (Speaker):
Hard Drive Reset Power LED
Activity LED Switch
Connects to the speaker on the chassis front panel. The system reports
Chassis system startup status by issuing a beep code. One single short beep
Intrusion Header
will be heard if no problem is detected at system startup.
•• HD (Hard Drive Activity LED):
Connects to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive
is reading or writing data.
•• RES (Reset Switch):
Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer
if the computer freezes and fails to perform a normal restart.
•• CI (Chassis Intrusion Header):
Connects to the chassis intrusion switch/sensor on the chassis that can detect if the chassis cover has
been removed. This function requires a chassis with a chassis intrusion switch/sensor.
•• NC: No Connection.

The front panel design may differ by chassis. A front panel module mainly consists of power switch,
reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis
front panel module to this header, make sure the wire assignments and the pin assignments are
matched correctly.

7) F_AUDIO (Front Panel Audio Header)

The front panel audio header supports High Definition audio (HD). You may connect your chassis front
panel audio module to this header. Make sure the wire assignments of the module connector match the
pin assignments of the motherboard header. Incorrect connection between the module connector and the
motherboard header will make the device unable to work or even damage it.
Pin No. Definition Pin No. Definition
9 1 1 MIC L 6 MIC Detection
10 2 2 7
GND SENSE_SEND
3 MIC R 8 No Pin
4 NC 9 Head Phone L
5 Head Phone R 10 Head Phone Detection

Some chassis provide a front panel audio module that has separated connectors on each wire
instead of a single plug. For information about connecting the front panel audio module that has
different wire assignments, please contact the chassis manufacturer.

- 16 -
SB30 8) F_USB30 (USB 3.1 F_
GenU 1 Header) F_
The header conforms to USB 3.1 Gen 1 and USB 2.0 specification and can provide two USB ports. For
purchasing the optional 3.5" front panel that provides two USB 3.1 Gen 1 ports, please contact the local
dealer.

Pin No. Definition Pin No. Definition

1 VBUS 11 D2+
20 1
2 SSRX1- 12 D2-
3 SSRX1+ 13 GND
4 GND 14 SSTX2+
B SS
B_ 5 SSTX1- 15 SSTX2-
6 SSTX1+ 16 GND

1
1

11 10 7 GND 17 SSRX2+
1
_S
8 D1- 18 SSRX2-

1
9 D1+ 19 VBUS
10 NC 20 No Pin

S
1 2 3

1 2 3

1 2 3 1 2 3

9) F_USB (USB 2.0/1.1 Header)

The header conforms to USB 2.0/1.1 specification. Each USB header can provide two USB ports via an
optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer.

Pin No. Definition Pin No. Definition

S 3 1 B SPower
S (5V)
S 6 USB DY+ U
_ _ 3
9 1 2 Power (5V) 7 GND
10 2 3 USB DX- 8 GND
4 USB DY- 9 No Pin
5 USB DX+ 10 NC
S _
S F
_
Prior to installing the USB bracket, be sure to turn off your computer and unplug the power cord
from the power outlet to prevent damage to the USB bracket.
_ _B

B_ _
S _S

S _
- 17 -
 _0

10) TPM (Trusted Platform Module Header)

_ _B You may
_ connect a TPM
S _ (Trusted Platform Module) to this header.

_ F
Pin No. Definition Pin No. Definition
11 1 1 LAD0 7 LAD3
12 2 2 VCC3 8 GND
3 LAD1 9 LFRAME
4 No Pin 10 NC
5 LAD2 11 SERIRQ _ 0 F

6 LCLK 12 LRESET

11) CLR_CMOS (Clear CMOS Jumper)

Use this jumper to clear the BIOS configuration and reset the CMOS values to factory defaults. To clear
S F_ the CMOS values, use a metal object like a screwdriver to touch the two pins for a few seconds.

Open: Normal
B B_
Short: Clear CMOS Values

•• Always turn off your computer and unplug the power cord from the power outlet before clearing
the CMOS values. _3 U
•• After system restart, go to BIOS Setup to load factory defaults (select Load Optimized Defaults) or
manually configure the BIOS settings (refer to Chapter 2, "BIOS Setup," for BIOS configurations).

12) BAT (Battery)

The battery provides power to keep the values (such as BIOS configurations, date, and time information)
SB3 F_USB30 3 CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a low
in the
level, or the CMOS values may not be accurate or may be lost.
You may clear the CMOS values by removing the battery:
1. Turn off your computer and unplug the power cord.
2. Gently remove the battery from the battery holder and wait for one minute. (Or use a
metal object like a screwdriver to touch the positive and negative terminals of the battery
holder, making them short for 5 seconds.)
3. Replace the battery.
4. Plug in the power cord and restart your computer.
•• Always turn off your computer and unplug the power cord before replacing the battery.
•• Replace the battery with an equivalent one. Damage to your devices may occur if the battery is
replaced with an incorrect model.
•• Contact the place of purchase or local dealer if you are not able to replace the battery by yourself
or uncertain about the battery model.
•• When installing the battery, note the orientation of the positive side (+) and the negative side (-)
of the battery (the positive side should face up).
•• Used batteries must be handled in accordance with local environmental regulations.

- 18 -
 B S_
B

13) M2A (M.2 Socket 3 Connector)

The M.2 connector supports M.2 SATA SSDs and M.2 PCIe SSDs.

S
S

80 60 42

Follow the steps below to correctly install an M.2 SSD in the M.2 connector.
Step 1:
Locate the proper mounting hole for the M.2 SSD to be installed and then install the mounting clip first.
Step 2:
F
Pull the clip's tab up and out of the mounting hole. Slide the M.2 SSD into the connector at an angle.
Step 3:
Press the M.2 SSD down and then secure it by pressing the clip's tab into the mounting hole.

Installation Notices for _the

0 M.2 and SATA Connectors:
The availability of the SATA connectors may be affected by the type of device installed in the M.2 sockets.
The M2A connector shares bandwidth with the SATA3 3 connector. Refer to the following table for details.
Connector
Type of SATA3 0 SATA3 1 SATA3 2 SATA3 3
M.2 SSD

M.2 SATA SSD a_ F a a r

M.2 PCIe SSD a a a a

No M.2 SSD Installed a a a a

a: Available, r: Not available

_0 F

_3 U

- 19 -
Chapter 3 BIOS Setup
BIOS (Basic Input and Output System) records hardware parameters of the system in the CMOS on the
motherboard. Its major functions include conducting the Power-On Self-Test (POST) during system startup,
saving system parameters and loading operating system, etc. BIOS includes a BIOS Setup program that allows
the user to modify basic system configuration settings or to activate certain system features.
When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS to
keep the configuration values in the CMOS.
To access the BIOS Setup program, press the <Delete> key during the POST when the power is turned on.
To upgrade the BIOS, use either the GIGABYTE Q-Flash or @BIOS utility.
•• Q-Flash allows the user to quickly and easily upgrade or back up BIOS without entering the operating system.
•• @BIOS is a Windows-based utility that searches and downloads the latest version of BIOS from the Internet
and updates the BIOS.

•• Because BIOS flashing is potentially risky, if you do not encounter problems using the current
version of BIOS, it is recommended that you not flash the BIOS. To flash the BIOS, do it with
caution. Inadequate BIOS flashing may result in system malfunction.
•• It is recommended that you not alter the default settings (unless you need to) to prevent system
instability or other unexpected results. Inadequately altering the settings may result in system's
failure to boot. If this occurs, try to clear the CMOS values and reset the board to default values.
(Refer to the "Load Optimized Defaults" section in this chapter or introductions of the battery/clear
CMOS jumper in Chapter 1 for how to clear the CMOS values.)

3-1 Startup Screen

The following startup Logo screen will appear when the computer boots.

Function Keys

There are two different BIOS modes as follows and you can use the <F2> key to switch between the two modes.
The Classic Setup mode provides detailed BIOS settings. You can press the arrow keys on your keyboard to move
among the items and press <Enter> to accept or enter a sub-menu. Or you can use your mouse to select the
item you want. Easy Mode allows users to quickly view their current system information or to make adjustments
for optimum performance. In Easy Mode, you can use your mouse to move through configuration items.

•• When the system is not stable as usual, select the Load Optimized Defaults item to set your system to its defaults.
•• The BIOS Setup menus described in this chapter are for reference only and may differ by BIOS version.

- 20 -
 3-2 The Main Menu

System Time
Setup Menus

Hardware
Information

Configuration Items Current Settings Quick Access Bar allows you to enter Easy Mode, select BIOS
default language, configure fan settings, or enter Q-Flash.

Classic Setup Function Keys

<f><g> Move the selection bar to select a setup menu
<h><i> Move the selection bar to select an configuration item on a menu
<Enter>/Double Click Execute command or enter a menu
<+>/<Page Up> Increase the numeric value or make changes
<->/<Page Down> Decrease the numeric value or make changes
<F1> Show descriptions of the function keys
<F2> Switch to Easy Mode
<F3> Save the current BIOS settings to a profile
<F4> Load the BIOS settings from a profile created before
<F5> Restore the previous BIOS settings for the current submenus
<F7> Load the Optimized BIOS default settings for the current submenus
<F8> Access the Q-Flash utility
<F9> Display system information
<F10> Save all the changes and exit the BIOS Setup program
<F12> Capture the current screen as an image and save it to your USB drive
Main Menu: Exit the BIOS Setup program
<Esc>/<Right Click>
Submenus: Exit current submenu

- 21 -
3-3 M.I.T.

Whether the system will work stably with the overclock/overvoltage settings you made is dependent on your overall
system configurations. Incorrectly doing overclock/overvoltage may result in damage to CPU, chipset, or memory
and reduce the useful life of these components. This page is for advanced users only and we recommend you not to
alter the default settings to prevent system instability or other unexpected results. (Inadequately altering the settings
may result in system's failure to boot. If this occurs, clear the CMOS values and reset the board to default values.)
`` Advanced Frequency Settings
&& Host Clock Value
Displays the current operating Host Clock frequency.
&& Graphics Slice Ratio (Note)
Allows you to set the Graphics Slice Ratio.
&& Graphics UnSlice Ratio (Note)
Allows you to set the Graphics UnSlice Ratio.

&& CPU Upgrade (Note)

Allows you to set the CPU frequency. Options may vary depending on the CPU being used. (Default: Auto)
&& CPU Clock Ratio
Allows you to alter the clock ratio for the installed CPU.
&& CPU Frequency
Displays the current operating CPU frequency.
&& FCLK Frequency for Early Power On
Allows you to set the FCLK frequency. Options are: Normal(800Mhz), 1GHz, 400MHz. (Default: 1GHz)

`` Advanced CPU Core Settings

&& CPU Clock Ratio, CPU Frequency, FCLK Frequency for Early Power On
The settings above are synchronous to those under the same items on the Advanced Frequency Settings
menu.
(Note) This item is present only when you install a CPU that supports this feature. For more information about
Intel® CPUs' unique features, please visit Intel's website.

- 22 -
&& Uncore Ratio
Allows you to set the CPU Uncore ratio. The adjustable range is dependent on the CPU being used.
&& Uncore Frequency
Displays the current CPU Uncore frequency.
&& CPU Flex Ratio Override
Enables or disables the CPU Flex Ratio. The maximum CPU clock ratio will be based on the CPU Flex
Ratio Settings value if CPU Clock Ratio is set to Auto. (Default: Disabled)
&& CPU Flex Ratio Settings
Allows you to set the CPU Flex Ratio. The adjustable range may vary by CPU.
&& Intel(R) Turbo Boost Technology (Note)
Allows you to determine whether to enable the Intel® CPU Turbo Boost technology. Auto lets the BIOS
automatically configure this setting. (Default: Auto)
&& Turbo Ratio (Note)
Allows you to set the CPU Turbo ratios for different number of active cores. Auto sets the CPU Turbo ratios
according to the CPU specifications. (Default: Auto)
&& No. of CPU Cores Enabled (Note)
Allows you to select the number of CPU cores to enable in an Intel® multi-core CPU (the number of CPU
cores may vary by CPU). Auto lets the BIOS automatically configure this setting. (Default: Auto)
&& Hyper-Threading Technology (Note)
Allows you to determine whether to enable multi-threading technology when using an Intel® CPU that
supports this function. This feature only works for operating systems that support multi-processor mode.
Auto lets the BIOS automatically configure this setting. (Default: Auto)
&& Intel(R) Speed Shift Technology (Intel® Speed Shift Technology) (Note)
Enables or disables Intel® Speed Shift Technology. Enabling this feature allows the processor to ramp up
its operating frequency more quickly and then improves the system responsiveness. (Default: Auto)
&& CPU Enhanced Halt (C1E) (Note)
Enables or disables Intel® CPU Enhanced Halt (C1E) function, a CPU power-saving function in system
halt state. When enabled, the CPU core frequency and voltage will be reduced during system halt state to
decrease power consumption. Auto lets the BIOS automatically configure this setting. (Default: Auto)
&& C3 State Support (Note)
Allows you to determine whether to let the CPU enter C3 mode in system halt state. When enabled, the
CPU core frequency and voltage will be reduced during system halt state to decrease power consumption.
The C3 state is a more enhanced power-saving state than C1. Auto lets the BIOS automatically configure
this setting. (Default: Auto)
&& C6/C7 State Support (Note)
Allows you to determine whether to let the CPU enter C6/C7 mode in system halt state. When enabled, the
CPU core frequency and voltage will be reduced during system halt state to decrease power consumption.
The C6/C7 state is a more enhanced power-saving state than C3. Auto lets the BIOS automatically configure
this setting. (Default: Auto)
&& C8 State Support (Note)
Allows you to determine whether to let the CPU enter C8 mode in system halt state. When enabled, the CPU
core frequency and voltage will be reduced during system halt state to decrease power consumption. The
C8 state is a more enhanced power-saving state than C6/C7. Auto lets the BIOS automatically configure
this setting. (Default: Auto)

(Note) This item is present only when you install a CPU that supports this feature. For more information about
Intel® CPUs' unique features, please visit Intel's website.

- 23 -
&& C10 State Support (Note 1)
Allows you to determine whether to let the CPU enter C10 mode in system halt state. When enabled, the
CPU core frequency and voltage will be reduced during system halt state to decrease power consumption.
The C10 state is a more enhanced power-saving state than C8. Auto lets the BIOS automatically configure
this setting. (Default: Auto)
&& Package C State Limit (Note 1)
Allows you to specify the C-state limit for the processor. Auto lets the BIOS automatically configure this setting.
(Default: Auto)
&& CPU Thermal Monitor (Note 1)
Enables or disables Intel® Thermal Monitor function, a CPU overheating protection function. When enabled,
the CPU core frequency and voltage will be reduced when the CPU is overheated. Auto lets the BIOS
automatically configure this setting. (Default: Auto)
&& Ring to Core offset (Down Bin)
Allows you to determine whether to disable the CPU Ring ratio auto-down function. Auto lets the BIOS
automatically configure this setting. (Default: Auto)
&& CPU EIST Function (Note 1)
Enables or disables Enhanced Intel® Speed Step Technology (EIST). Depending on CPU loading, Intel®
EIST technology can dynamically and effectively lower the CPU voltage and core frequency to decrease
average power consumption and heat production. Auto lets the BIOS automatically configure this setting.
(Default: Auto)
&& Race To Halt (RTH) (Note 1)/Energy Efficient Turbo (Note 1)
Enables or disables the CPU power saving related settings.
&& Voltage Optimization
Allows you to determine whether to enable voltage optimization to reduce power consumption. (Default:
Auto)
&& Hardware Prefetcher
Allows you to determine whether to enable hardware prefetcher to prefetch data and instructions from the
memory into the cache. (Default: Auto)
&& Adjacent Cache Line Prefetch
Allows you to determine whether to enable the adjacent cache line prefetch mechanism that lets the
processor retrieve the requested cache line as well as the subsequent cache line. (Default: Auto)

&& Extreme Memory Profile (X.M.P.) (Note 2)

Allows the BIOS to read the SPD data on XMP memory module(s) to enhance memory performance when
enabled.

Disabled Disables this function. (Default)

Profile1 Uses Profile 1 settings.

Profile2 (Note 2)
Uses Profile 2 settings.
&& System Memory Multiplier
Allows you to set the system memory multiplier. Auto sets memory multiplier according to memory SPD
data. (Default: Auto)
&& Memory Ref Clock
Allows you to manually adjust the memory reference clock. (Default: Auto)

(Note 1) This item is present only when you install a CPU that supports this feature. For more information about
Intel® CPUs' unique features, please visit Intel's website.
(Note 2) This item is present only when you install a CPU and a memory module that support this feature.
- 24 -
&& Memory Odd Ratio (100/133 or 200/266)
Allows you to manually adjust the memory reference clock. (Default: Auto)
&& Memory Frequency (MHz)
The first memory frequency value is the normal operating frequency of the memory being used; the second
is the memory frequency that is automatically adjusted according to the System Memory Multiplier settings.

`` Advanced Memory Settings

&& Extreme Memory Profile (X.M.P.) (Note), System Memory Multiplier, Memory Ref Clock,
Memory Odd Ratio (100/133 or 200/266), Memory Frequency(MHz)
The settings above are synchronous to those under the same items on the Advanced Frequency Settings
menu.
&& Memory Boot Mode (Note)
Provides memory detection and training methods.

Auto Lets the BIOS automatically configure this setting. (Default)

Normal  The BIOS automatically performs memory training. Please note that if the system
becomes unstable or unbootable, try to clear the CMOS values and reset the board
to default values. (Refer to the introductions of the battery/clear CMOS jumper in
Chapter 1 for how to clear the CMOS values.)

Enable Fast Boot Skip memory detection and training in some specific criteria for faster memory
boot.

Disable Fast Boot Detect and train memory at every single boot.
&& Realtime Memory Timing
Allows you to fine-tune memory timings after the BIOS stage. (Default: Auto)

&& Memory Enhancement Settings

Provides several memory performance enhancement settings: Normal (basic performance), Relax OC,
Enhanced Stability, and Enhanced Performance. (Default: Normal)
&& Memory Timing Mode
Manual and Advanced Manual allows the Memory Multiplier Tweaker, Channel Interleaving, Rank
Interleaving, and memory timing settings below to be configurable. Options are: Auto (default), Manual,
Advanced Manual.
&& Profile DDR Voltage
When using a non-XMP memory module or Extreme Memory Profile (X.M.P.) is set to Disabled, the value
is displayed according to your memory specification. When Extreme Memory Profile (X.M.P.) is set to
Profile1 or Profile2, the value is displayed according to the SPD data on the XMP memory.
&& Memory Multiplier Tweaker
Provides different levels of memory auto-tuning. (Default: Auto)
&& Channel Interleaving
Enables or disables memory channel interleaving. Enabled allows the system to simultaneously access
different channels of the memory to increase memory performance and stability. Auto lets the BIOS
automatically configure this setting. (Default: Auto)
&& Rank Interleaving
Enables or disables memory rank interleaving. Enabled allows the system to simultaneously access different ranks
of the memory to increase memory performance and stability. Auto lets the BIOS automatically configure this setting.
(Default: Auto)

(Note) This item is present only when you install a CPU and a memory module that support this feature.
- 25 -
`` Channel A/B Memory Sub Timings
This sub-menu provides memory timing settings for each channel of memory. The respective timing setting
screens are configurable only when Memory Timing Mode is set to Manual or Advanced Manual. Note: Your
system may become unstable or fail to boot after you make changes on the memory timings. If this occurs,
please reset the board to default values by loading optimized defaults or clearing the CMOS values.

`` Advanced Voltage Settings

`` Advanced Power Settings
&& CPU Vcore Loadline Calibration
Allows you to configure Load-Line Calibration for the CPU Vcore voltage. Selecting a higher level keeps
the CPU Vcore voltage more consistent with what is set in BIOS under heavy load. Auto lets the BIOS
automatically configure this setting and sets the voltage following Intel's specifications. (Default: Auto)

`` CPU Core Voltage Control

This section provides CPU voltage control options.

`` DRAM Voltage Control

This section provides memory voltage control options.

`` Internal VR Control
This section provides VR voltage control options.

`` PC Health Status
&& Reset Case Open Status

Disabled Keeps or clears the record of previous chassis intrusion status. (Default)

Enabled  Clears the record of previous chassis intrusion status and the Case Open field will
show "No" at next boot.
&& Case Open
Displays the detection status of the chassis intrusion detection device attached to the motherboard CI
header. If the system chassis cover is removed, this field will show "Yes", otherwise it will show "No". To
clear the chassis intrusion status record, set Reset Case Open Status to Enabled, save the settings to
the CMOS, and then restart your system.
&& CPU Vcore/CPU VCCSA/DRAM Channel A/B Voltage/+3.3V/+5V/+12V/CPU VAXG
Displays the current system voltages.

`` Miscellaneous Settings
&& Max Link Speed
Allows you to set the operation mode of the PCI Express slots to Gen 1, Gen 2, or Gen 3. Actual operation
mode is subject to the hardware specification of each slot. Auto lets the BIOS automatically configure this
setting. (Default: Auto)
&& 3DMark01 Enhancement
Allows you to determine whether to enhance some legacy benchmark performance. (Default: Disabled)

- 26 -
`` Smart Fan 5 Settings
&& Monitor
Allows you to select a target to monitor and to make further adjustment. (Default: CPU FAN)
&& Fan Speed Control
Allows you to determine whether to enable the fan speed control function and adjust the fan speed.

Normal  Allows the fan to run at different speeds according to the temperature. You can adjust
the fan speed with System Information Viewer based on your system requirements.
(Default)

Silent Allows the fan to run at slow speeds.

Manual Allows you to control the fan speed in the curve graph.
 Speed
Full Allows the fan to run at full speeds.
&& Fan Control Use Temperature Input
Allows you to select the reference temperature for fan speed control.
&& Temperature Interval
Allows you to select the temperature interval for fan speed change.
&& Fan Control Mode

Auto  Lets the BIOS automatically detect the type of fan installed and sets the optimal control
mode. (Default)

Voltage Voltage mode is recommended for a 3-pin fan.

PWM PWM mode is recommended for a 4-pin fan.
&& Fan Stop
Enables or disables the fan stop function. You can set the temperature limit using the temperature curve.
The fan stops operation when the temperature is lower than the limit. (Default: Disabled)
&& Temperature
Displays the current temperature of the selected target area.
&& Fan Speed
Displays current fan speeds.
&& Temperature Warning Control
Sets the warning threshold for temperature. When temperature exceeds the threshold, BIOS will emit
warning sound. Options are: Disabled (default), 60oC/140oF, 70oC/158oF, 80oC/176oF, 90oC/194oF.
&& Fan Fail Warning
Allows the system to emit warning sound if the fan is not connected or fails. Check the fan condition or fan
connection when this occurs. (Default: Disabled)

- 27 -
3-4 System

This section provides information on your motherboard model and BIOS version. You can also select the default
language used by the BIOS and manually set the system time.

&& Access Level

Displays the current access level depending on the type of password protection used. (If no password is
set, the default will display as Administrator.) The Administrator level allows you to make changes to all
BIOS settings; the User level only allows you to make changes to certain BIOS settings but not all.
&& System Language
Selects the default language used by the BIOS.
&& System Date
Sets the system date. The date format is week (read-only), month, date and year. Use <Enter> to switch
between the Month, Date, and Year fields and use the <Page Up> or <Page Down> key to set the desired
value.
&& System Time
Sets the system time. The time format is hour, minute, and second. For example, 1 p.m. is 13:00:00. Use
<Enter> to switch between the Hour, Minute, and Second fields and use the <Page Up> or <Page Down>
key to set the desired value.

- 28 -
3-5 BIOS

&& Bootup NumLock State

Enables or disables Numlock feature on the numeric keypad of the keyboard after the POST. (Default: On)
&& Security Option
Specifies whether a password is required every time the system boots, or only when you enter BIOS Setup.
After configuring this item, set the password(s) under the Administrator Password/User Password item.

Setup  A password is only required for entering the BIOS Setup program.

System  A password is required for booting the system and for entering the BIOS Setup
program. (Default)
&& Full Screen LOGO Show
Allows you to determine whether to display the GIGABYTE Logo at system startup. Disabled skips the
GIGABYTE Logo when the system starts up. (Default: Enabled)
&& Boot Option Priorities
Specifies the overall boot order from the available devices. Removable storage devices that support GPT
format will be prefixed with "UEFI:" string on the boot device list. To boot from an operating system that
supports GPT partitioning, select the device prefixed with "UEFI:" string.
Or if you want to install an operating system that supports GPT partitioning such as Windows 10 64-bit,
select the optical drive that contains the Windows 10 64-bit installation disk and is prefixed with "UEFI:"
string.
&& Hard Drive/CD/DVD ROM Drive/Floppy Drive/Network Device BBS Priorities
Specifies the boot order for a specific device type, such as hard drives, optical drives, floppy disk drives,
and devices that support Boot from LAN function, etc. Press <Enter> on this item to enter the submenu that
presents the devices of the same type that are connected. This item is present only if at least one device
for this type is installed.

&& Fast Boot

Enables or disables Fast Boot to shorten the OS boot process. Ultra Fast provides the fastest bootup
speed. (Default: Disabled)

- 29 -
&& SATA Support

Last Boot HDD Only Except for the previous boot drive, all SATA devices are disabled before the OS
boot process completes.
 Sata Devices All SATA devices are functional in the operating system and during the POST.
All
(Default)
This item is configurable only when Fast Boot is set to Enabled or Ultra Fast.
&& VGA Support
Allows you to select which type of operating system to boot.

Auto Enables legacy option ROM only.
 Driver
EFI Enables EFI option ROM. (Default)
This item is configurable only when Fast Boot is set to Enabled or Ultra Fast.
&& USB Support

Disabled All USB devices are disabled before the OS boot process completes.
 Initial
Full All USB devices are functional in the operating system and during the POST.

Partial Initial Part of the USB devices are disabled before the OS boot process completes.
(Default)
This item is configurable only when Fast Boot is set to Enabled or Ultra Fast. This function is disabled
when Fast Boot is set to Ultra Fast.
&& PS2 Devices Support

Disabled All PS/2 devices are disabled before the OS boot process completes.

Enabled  All PS/2 devices are functional in the operating system and during the POST.
(Default)
This item is configurable only when Fast Boot is set to Enabled or Ultra Fast. This function is disabled
when Fast Boot is set to Ultra Fast.
&& NetWork Stack Driver Support

Disabled Disables booting from the network. (Default)

Enabled Enables booting from the network.
This item is configurable only when Fast Boot is set to Enabled or Ultra Fast.
&& Next Boot After AC Power Loss

Normal Boot Enables normal bootup upon the return of the AC power. (Default)

Fast Boot Keeps the Fast Boot settings upon the return of the AC power.
This item is configurable only when Fast Boot is set to Enabled or Ultra Fast.

&& Mouse Speed

Allows you to set the mouse cursor movement speed. (Default: 1 X)

&& Windows 8/10 Features

Allows you to select the operating system to be installed. (Default: Other OS)
&& CSM Support
Enables or disables UEFI CSM (Compatibility Support Module) to support a legacy PC boot process.

Disabled Disables UEFI CSM and supports UEFI BIOS boot process only.

Enabled Enables UEFI CSM. (Default)
&& LAN PXE Boot Option ROM
Allows you to select whether to enable the legacy option ROM for the LAN controller. (Default: Disabled)
This item is configurable only when CSM Support is set to Enabled.

- 30 -
&& Storage Boot Option Control
Allows you to select whether to enable the UEFI or legacy option ROM for the storage device controller.
Do not launch Disables option ROM.

Legacy Enables legacy option ROM only.

UEFI Enables UEFI option ROM only. (Default)
This item is configurable only when CSM Support is set to Enabled.
&& Other PCI devices
Allows you to select whether to enable the UEFI or Legacy option ROM for the PCI device controller other
than the LAN, storage device, and graphics controllers.
Do not launch Disables option ROM.

Legacy Enables legacy option ROM only.

UEFI Enables UEFI option ROM only. (Default)
This item is configurable only when CSM Support is set to Enabled.

&& Administrator Password

Allows you to configure an administrator password. Press <Enter> on this item, type the password, and
then press <Enter>. You will be requested to confirm the password. Type the password again and press
<Enter>. You must enter the administrator password (or user password) at system startup and when entering
BIOS Setup. Differing from the user password, the administrator password allows you to make changes to
all BIOS settings.
&& User Password
Allows you to configure a user password. Press <Enter> on this item, type the password, and then press
<Enter>. You will be requested to confirm the password. Type the password again and press <Enter>.
You must enter the administrator password (or user password) at system startup and when entering BIOS
Setup. However, the user password only allows you to make changes to certain BIOS settings but not all.

To cancel the password, press <Enter> on the password item and when requested for the password, enter
the correct one first. When prompted for a new password, press <Enter> without entering any password.
Press <Enter> again when prompted to confirm.
NOTE: Before setting the User Password, be sure to set the Administrator Password first.

&& Secure Boot

Allows you to enable or disable Secure Boot and configure related settings. This item is configurable only
when CSM Support is set to Disabled.

- 31 -
3-6 Peripherals

&& Initial Display Output

Specifies the first initiation of the monitor display from the installed PCI Express graphics card or the onboard
graphics.

IGFX Sets the onboard graphics as the first display.

PCIe 1 Slot Sets the graphics card on the PCIEX16 slot as the first display. (Default)
&& OnBoard LAN Controller
Enables or disables the onboard LAN function. (Default: Enabled)
If you wish to install a 3rd party add-in network card instead of using the onboard LAN, set this item to
Disabled.
&& Above 4G Decoding
Enables or disables 64-bit capable devices to be decoded in above 4 GB address space (only if your system
supports 64-bit PCI decoding). Set to Enabled if more than one advanced graphics card are installed and
their drivers are not able to be launched when entering the operating system (because of the limited 4 GB
memory address space). (Default: Disabled)
&& Intel Platform Trust Technology (PTT)
Enables or disables Intel® PTT Technology. (Default: Disabled)
&& SW Guard Extensions (SGX)
Enables or disables the Intel® Software Guard Extensions technology. This feature allows legal software
to operate in a safe environment and protects the software against attacks from malicious software. The
Software Controlled option allows you to enable or disable this feature with an Intel-provided application.
(Default: Software Controlled)

`` Realtek PCIe GBE Family Controller

This sub-menu provides information on LAN configuration and related configuration options.

- 32 -
`` OffBoard SATA Controller Configuration
Displays information on your M.2 PCIe SSD if installed.

`` Trusted Computing
Enables or disables Trusted Platform Module (TPM).

`` USB Configuration
&& Legacy USB Support
Allows USB keyboard/mouse to be used in MS-DOS. (Default: Enabled)
&& XHCI Hand-off
Determines whether to enable XHCI Hand-off feature for an operating system without XHCI Hand-off
support. (Default: Disabled)
&& USB Mass Storage Driver Support
Enables or disables support for USB storage devices. (Default: Enabled)
&& Port 60/64 Emulation
Enables or disables emulation of I/O ports 64h and 60h. This should be enabled for full legacy support
for USB keyboards/mice in MS-DOS or in operating system that does not natively support USB devices.
(Default: Enabled)
&& Mass Storage Devices
Displays a list of connected USB mass storage devices. This item appears only when a USB storage device
is installed.

`` Network Stack Configuration

&& Network Stack
Disables or enables booting from the network to install a GPT format OS, such as installing the OS from
the Windows Deployment Services server. (Default: Disabled)
&& Ipv4 PXE Support
Enables or disables IPv4 PXE Support. This item is configurable only when Network Stack is enabled.
&& Ipv4 HTTP Support
Enables or disables HTTP boot support for IPv4. This item is configurable only when Network Stack is
enabled.
&& Ipv6 PXE Support
Enables or disables IPv6 PXE Support. This item is configurable only when Network Stack is enabled.
&& Ipv6 HTTP Support
Enables or disables HTTP boot support for IPv6. This item is configurable only when Network Stack is
enabled.
&& IPSEC Certificate
Enables or disables the Internet Protocol Security. This item is configurable only when Network Stack is
enabled.
&& PXE boot wait time
Allows you to configure how long to wait before you can press <Esc> to abort the PXE boot. This item is
configurable only when Network Stack is enabled. (Default: 0)
&& Media detect count
Allows you to set the number of times to check the presence of media. This item is configurable only when
Network Stack is enabled. (Default: 1)

- 33 -
`` NVMe Configuration
Displays information on your PCIe SSD if installed.

`` SATA And RST Configuration

&& SATA Controller(s)
Enables or disables the integrated SATA controllers. (Default: Enabled)
&& SATA Mode Selection
Specifies the operating mode of the integrated SATA controllers.

AHCI  Configures the SATA controllers to AHCI mode. Advanced Host Controller Interface
(AHCI) is an interface specification that allows the storage driver to enable advanced
Serial ATA features such as Native Command Queuing and hot plug. (Default)
&& Aggressive LPM Support
Enables or disables the power saving feature, ALPM (Aggressive Link Power Management), for the Chipset
SATA controllers. (Default: Enabled)
&& Port 0/1/2/3
Enables or disables each SATA port. (Default: Enabled)
&& Hot plug
Enables or disable the hot plug capability for each SATA port. (Default: Disabled)
&& Configured as eSATA
Enables or disables support for external SATA devices.
&& Mechanical Presence Switch
Allows you to determine whether to turn on the Mechanical Presence switch for the SATA device. This item
is configurable only when Hot plug is enabled. (Default: Enabled)

- 34 -
3-7 Chipset

&& VT-d (Note)

Enables or disablesIntel® Virtualization Technology for Directed I/O. (Default: Enabled)
&& Internal Graphics
Enables or disables the onboard graphics function. (Default: Auto)
&& DVMT Pre-Allocated
Allows you to set the onboard graphics memory size. Options are: 32M~1024M. (Default: 64M)
&& DVMT Total Gfx Mem
Allows you to allocate the DVMT memory size of the onboard graphics. Options are: 128M, 256M, MAX.
(Default: 256M)
&& Audio Controller
Enables or disables the onboard audio function. (Default: Enabled)
If you wish to install a 3rd party add-in audio card instead of using the onboard audio, set this item to
Disabled.

&& IOAPIC 24-119 Entries

Enables or disables this function. (Default: Enabled)

(Note) This item is present only when you install a CPU that supports this feature. For more information about
Intel® CPUs' unique features, please visit Intel's website.

- 35 -
3-8 Power

&& Platform Power Management

Enables or disables the Active State Power Management function (ASPM). (Default: Disabled)
&& PEG ASPM
Allows you to configure the ASPM mode for the device connected to the CPU PEG bus. This item is
configurable only when Platform Power Management is set to Enabled. (Default: Enabled)
&& PCH ASPM
Allows you to configure the ASPM mode for the device connected to Chipset's PCI Express bus. This item
is configurable only when Platform Power Management is set to Enabled. (Default: Enabled)
&& DMI ASPM
Allows you to configure the ASPM mode for both CPU side and Chipset side of the DMI link. This item is
configurable only when Platform Power Management is set to Enabled. (Default: Enabled)

&& AC BACK
Determines the state of the system after the return of power from an AC power loss.

Memory The system returns to its last known awake state upon the return of the AC power.

Always On The system is turned on upon the return of the AC power.

Always Off The system stays off upon the return of the AC power. (Default)
&& Power On By Keyboard
Allows the system to be turned on by a PS/2 keyboard wake-up event.
Note: To use this function, you need an ATX power supply providing at least 1A on the +5VSB lead.

Disabled Disables this function. (Default)

Password Set a password with 1~5 characters to turn on the system.

Keyboard 98 Press POWER button on the Windows 98 keyboard to turn on the system.
 Key
Any Press any key to turn on the system.

- 36 -
&& Power On Password
Set the password when Power On By Keyboard is set to Password.
Press <Enter> on this item and set a password with up to 5 characters and then press <Enter> to accept.
To turn on the system, enter the password and press <Enter>.
Note: To cancel the password, press <Enter> on this item. When prompted for the password, press <Enter>
again without entering the password to clear the password settings.
&& Power On By Mouse
Allows the system to be turned on by a PS/2 mouse wake-up event.
Note: To use this function, you need an ATX power supply providing at least 1A on the +5VSB lead.

Disabled Disables this function. (Default)

Move Move the mouse to turn on the system.

Double Click Double click on left button on the mouse to turn on the system.
&& ErP
Determines whether to let the system consume least power in S5 (shutdown) state. (Default: Disabled)
Note: When this item is set to Enabled, the following functions will become unavailable: Resume by Alarm,
power on by mouse, and power on by keyboard.
&& Soft-Off by PWR-BTTN
Configures the way to turn off the computer in MS-DOS mode using the power button.

Instant-Off Press the power button and then the system will be turned off instantly. (Default)

Delay 4 Sec Press and hold the power button for 4 seconds to turn off the system. If the power button
is pressed for less than 4 seconds, the system will enter suspend mode.
&& Resume by Alarm
Determines whether to power on the system at a desired time. (Default: Disabled)
If enabled, set the date and time as following:

Wake up day: Turn on the system at a specific time on each day or on a specific day in a month.

Wake up hour/minute/second: Set the time at which the system will be powered on automatically.
Note: When using this function, avoid inadequate shutdown from the operating system or removal of the
AC power, or the settings may not be effective.
&& Power Loading
Enables or disables dummy load. When the power supply is at low load, a self-protection will activate causing
it to shutdown or fail. If this occurs, please set to Enabled. Auto lets the BIOS automatically configure this
setting. (Default: Auto)
&& CEC 2019 Ready
Allows you to select whether to allow the system to adjust power consumption when it is in shutdown, idle,
or standby state in order to comply with the CEC (California Energy Commission) 2019 Standards. (Default:
Disabled)
&& RC6(Render Standby)
Allows you to determine whether to let the onboard graphics enter standby mode to decrease power
consumption. (Default: Enabled)

- 37 -
3-9 Save & Exit

&& Save & Exit Setup

Press <Enter> on this item and select Yes. This saves the changes to the CMOS and exits the BIOS Setup
program. Select No or press <Esc> to return to the BIOS Setup Main Menu.
&& Exit Without Saving
Press <Enter> on this item and select Yes. This exits the BIOS Setup without saving the changes made
in BIOS Setup to the CMOS. Select No or press <Esc> to return to the BIOS Setup Main Menu.
&& Load Optimized Defaults
Press <Enter> on this item and select Yes to load the BIOS factory default settings. The BIOS defaults
settings help the system to operate in optimum state. Always load the Optimized defaults after updating
the BIOS or after clearing the CMOS values.
&& Boot Override
Allows you to select a device to boot immediately. Press <Enter> on the device you select and select Yes
to confirm. Your system will restart automatically and boot from that device.
&& Save Profiles
This function allows you to save the current BIOS settings to a profile. You can create up to 8 profiles and
save as Setup Profile 1~ Setup Profile 8. Press <Enter> to complete. Or you can select Select File in
HDD/FDD/USB to save the profile to your storage device.
&& Load Profiles
If your system becomes unstable and you have loaded the BIOS default settings, you can use this function
to load the BIOS settings from a profile created before, without the hassles of reconfiguring the BIOS
settings. First select the profile you wish to load and then press <Enter> to complete. You can select Select
File in HDD/FDD/USB to input the profile previously created from your storage device or load the profile
automatically created by the BIOS, such as reverting the BIOS settings to the last settings that worked
properly (last known good record).

- 38 -
 Chapter 4 Drivers Installation
With the correct BIOS settings, you are ready to install the operating system. After you install the operating
system, a dialog box will appear on the bottom-right corner of the desktop asking if you want to download and
install the drivers and GIGABYTE applications via APP Center. Click Install to proceed with the installation. (In
BIOS Setup, make sure Peripherals\APP Center Download & Install Configuration\APP Center Download
& Install is set to Enabled.)

When the End User License Agreement dialog box appears, press <Accept> to install APP Center. On the APP
Center screen, select the drivers and applications you want to install and click Install.

Before the installation, make sure the system is connected to the Internet.

&& Please visit GIGABYTE's website for more software information.

https://www.gigabyte.com/WebPage/359/b360-app.html

&& Please visit GIGABYTE's website for more troubleshooting information.

https://www.gigabyte.com/WebPage/351/faq.html
- 39 -
Regulatory Notices
United States of America, Federal Communications Commission Statement

Supplier's Declaration of Conformity

47 CFR § 2.1077 Compliance Information

Product Name: Motherboard

Trade Name: GIGABYTE
Model Number: H310M M.2 2.0

Responsible Party – U.S. Contact Information: G.B.T. Inc.

Address: 17358 Railroad street, City Of Industry, CA91748
Tel.: 1-626-854-9338
Internet contact information: https://www.gigabyte.com

FCC Compliance Statement:

This device complies with Part 15 of the FCC Rules, Subpart B, Unintentional Radiators.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Battery Information
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits European Union—Disposal and recycling information
are designed to provide reasonable protection against harmful interference GIGABYTE Recycling Program (available in some regions)
in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance
with manufacturer's instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by This symbol indicates that this product and/or battery should not be disposed
turning the equipment off and on, the user is encouraged to try to correct the of with household waste. You must use the public collection system to return,
interference by one or more of the following measures: recycle, or treat them in compliance with the local regulations.
•• Reorient or relocate the receiving antenna. End of Life Directives-Recycling
•• Increase the separation between the equipment and receiver. The symbol shown below is on the product or on its packaging,
•• Connect the equipment to an outlet on a circuit different from that to which which indicates that this product must not be disposed of with
the receiver is connected. other waste. Instead, the device should be taken to the waste
•• Consult the dealer or an experienced radio/TV technician for help. collection centers for activation of the treatment, collection,
Canadian Department of Communications Statement recycling and disposal procedure.
This digital apparatus does not exceed the Class B limits for radio noise Déclaration de Conformité aux Directives de l'Union européenne (UE)
emissions from digital apparatus set out in the Radio Interference Regulations Cet appareil portant la marque CE est conforme aux directives de l'UE
of the Canadian Department of Communications. This class B digital apparatus suivantes: directive Compatibilité Electromagnétique 2014/30/UE, directive
complies with Canadian ICES-003. Basse Tension 2014/35/UE et directive RoHS II 2011/65/UE. La conformité à
Avis de conformité à la réglementation d'Industrie Canada ces directives est évaluée sur la base des normes européennes harmonisées
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du applicables.
Canada. European Union (EU) CE-Konformitätserklärung
European Union (EU) CE Declaration of Conformity Dieses Produkte mit CE-Kennzeichnung erfüllen folgenden EU-Richtlinien:
This device complies with the following directives: Electromagnetic EMV-Richtlinie 2014/30/EU, Niederspannungsrichtlinie 2014/30/EU und RoHS-
Compatibility Directive 2014/30/EU, Low-voltage Directive 2014/35/EU, Richtlinie 2011/65/EU erfüllt. Die Konformität mit diesen Richtlinien wird unter
RoHS directive (recast) 2011/65/EU & the 2015/863 Statement. This product Verwendung der entsprechenden Standards zurEuropäischen Normierung
has been tested and found to comply with all essential requirements of the beurteilt.
Directives. CE declaração de conformidade
European Union (EU) RoHS (recast) Directive 2011/65/EU & the European Este produto com a marcação CE estão em conformidade com das seguintes
Commission Delegated Directive (EU) 2015/863 Statement Diretivas UE: Diretiva Baixa Tensão 2014/35/EU; Diretiva CEM 2014/30/EU;
GIGABYTE products have not intended to add and safe from hazardous Diretiva RSP 2011/65/UE. A conformidade com estas diretivas é verificada
substances (Cd, Pb, Hg, Cr+6, PBDE, PBB, DEHP, BBP, DBP and DIBP). utilizando as normas europeias harmonizadas.
The parts and components have been carefully selected to meet RoHS CE Declaración de conformidad
requirement. Moreover, we at GIGABYTE are continuing our efforts to develop Este producto que llevan la marca CE cumplen con las siguientes Directivas
products that do not use internationally banned toxic chemicals. de la Unión Europea: Directiva EMC (2014/30/EU), Directiva de bajo voltaje
European Union (EU) Community Waste Electrical & Electronic (2014/35/EU), Directiva RoHS (recast) (2011/65/EU). El cumplimiento de estas
Equipment (WEEE) Directive Statement directivas se evalúa mediante las normas europeas armonizadas.
GIGABYTE will fulfill the national laws as interpreted from the 2012/19/EU Dichiarazione di conformità CE
WEEE (Waste Electrical and Electronic Equipment) (recast) directive. The Questo prodotto è conforme alle seguenti direttive: Direttiva sulla compatibilità
WEEE Directive specifies the treatment, collection, recycling and disposal of elettromagnetica 2014/30/UE, Direttiva sulla bassa tensione 2014/35/UE,
electric and electronic devices and their components. Under the Directive, used Direttiva RoHS (rifusione) 2011/65/UE. Questo prodotto è stato testato e
equipment must be marked, collected separately, and disposed of properly. trovato conforme a tutti i requisiti essenziali delle Direttive.
WEEE Symbol Statement
The symbol shown below is on the product or on its packaging,
which indicates that this product must not be disposed of with
other waste. Instead, the device should be taken to the waste D33006
collection centers for activation of the treatment, collection, RoHS
recycling and disposal procedure.

For more information about where you can drop off your waste equipment
for recycling, please contact your local government office, your household
waste disposal service or where you purchased the product for details of
environmentally safe recycling.

- 40 -
 Contact Us

GIGA-BYTE TECHNOLOGY CO., LTD.

Address: No.6, Baoqiang Rd., Xindian Dist., New Taipei City 231
TEL: +886-2-8912-4000, FAX: +886-2-8912-4005
Tech. and Non-Tech. Support (Sales/Marketing) : https://esupport.gigabyte.com
WEB address (English): https://www.gigabyte.com
WEB address (Chinese): https://www.gigabyte.com/tw

•• GIGABYTE eSupport
To submit a technical or non-technical (Sales/Marketing) question, please link to:
https://esupport.gigabyte.com

- 41 -