19-1749; Rev 0; 7/00

Dual-Supply, 180MHz, 16-Bit Accurate,

Ultra-Low Distortion Op Amps
General Description ____________________________Features

MAX4430–MAX4433
The MAX4430/MAX4431 single and MAX4432/MAX4433 ♦ 16-Bit Accurate Settling in 37ns
dual operational amplifiers feature wide bandwidth, 16- (MAX4430/MAX4432)
bit settling times in 37ns, and low-noise/low-distortion
operation. The MAX4430/MAX4432 are compensated for ♦ 100dB SFDR at 1MHz, 4Vp-p Output
unity gain stability and have a small signal -3dB band- ♦ 2.8nV/√Hz Input Voltage Noise Density
width of 180MHz. The MAX4431/MAX4433 are compen-
♦ 110dB (min) Open-Loop Gain
sated for closed-loop gains of +2 or greater and have a
small-signal -3dB bandwidth of 215MHz. ♦ 145V/µs Slew Rate (MAX4431/MAX4433)
The MAX4430–MAX4433 op amps require only 11mA of ♦ 60mA High Output Drive
supply current per amplifier while achieving 125dB open-
♦ Wide Voltage Swing Capable of Driving ADC
loop gain. Voltage noise density is a low 2.8nV/√Hz,
and provides 100dB spurious-free dynamic range Inputs with ≥4Vp-p Input Dynamic Range
(SFDR) at 1MHz. These characteristics make these op ♦ Available in Space-Saving Packages
amps ideal for driving modern high-speed 14- and 16- 5-pin SOT23 (MAX4430/MAX4431)
bit analog-to-digital converters (ADCs). 8-pin µMAX (MAX4432/MAX4433)
These high-speed op amps feature wide output voltage
swings capable of driving ADCs with ≥4V input dynamic Ordering Information
range and a high current output drive up to 60mA. Using PART TEMP. RANGE PIN-PACKAGE
a voltage feedback architecture, the MAX4430–
MAX4433 meet the requirements of many applications MAX4430EUK-T -40oC to +85oC 5 SOT23-5
that previously depended on current feedback ampli- MAX4430ESA -40oC to +85oC 8 SO
fiers. Ordering Information continued at end of data sheet.
The MAX4430/MAX4431 are available in a space-sav-
ing 5-pin SOT23 package, and the MAX4432/MAX4433 Selector Guide
are available in an 8-pin µMAX package.
SETTLING
MIN GAIN
BW TIME TO
PART AMPS STABLE
(MHz) 0.0015%
________________________Applications (V/V)
(ns)
High-Speed 14- and 16-Bit ADC Preamplifiers
MAX4430 1 +1 180 37
Low-Noise Preamplifiers MAX4431 1 +2 215 63
IF/RF Amplifiers MAX4432 2 +1 180 37
Low-Distortion Active Filters MAX4433 2 +2 215 63
High-Performance Receivers
Precision Instrumentation Typical Operating Circuit
VCC
Pin Configurations
C1
TOP VIEW
MAX4430 HIGH-SPEED
MAX4431 14-/16-BIT ADC
OUT 1 5 VCC
1 5
VEE 2
2
IN+ 3 4 IN-
IN 3 4
MAX4430
MAX4431
SOT23-5
C2
VEE
Pin Configurations continued at end of data sheet.

________________________________________________________________ Maxim Integrated Products 1

For free samples and the latest literature, visit www.maxim-ic.com or phone 1-800-998-8800.
For small orders, phone 1-800-835-8769.
 Dual-Supply, 180MHz, 16-Bit Accurate,
Ultra-Low Distortion Op Amps
ABSOLUTE MAXIMUM RATINGS
MAX4430–MAX4433

Supply Voltage (VCC to VEE)................................................+12V Operating Temperature Range ...........................-40°C to +85°C

Differential Input Voltage .......................................................+2V Junction Temperature ......................................................+150°C
Input Voltage Range ........................(VCC + 0.3V) to (VEE - 0.3V) Storage Temperature Range .............................-65°C to +150°C
Output Short-Circuit Duration to VCC or VEE ...................(Note 1) Lead Temperature (soldering, 10s) .................................+300°C
Current Into Any Input Pin ................................................±25mA
Continuous Power Dissipation (TA = +70°C)
5-Pin SOT23 (derate 7.1mW/°C above +70°C)............571mW
8-Pin µMAX (derate 4.5mW/°C above +70°C) .............330mW
8-Pin SO (derate 5.88mW/°C above +70°C)................471mW
Note 1: The MAX4430–MAX4433 are not protected for output short-circuit conditions.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.

DC ELECTRICAL CHARACTERISTICS
(VCC = +5V, VEE = -5V, RL = ∞, VCM = 0, and TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.) (Note 2)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Input Common-Mode Voltage VEE + VCC -
VCM Guaranteed by CMRR test V
Range 2.5 0.9
Input Offset Voltage VOS ±1.25 ±5 mV
Input Offset Voltage
TCVOS 7 µV / ° C
Temperature Coefficient
Input Offset Voltage Matching MAX4432/MAX4433 ±0.25 mV
Input Bias Current IB 11 30 µA
Input Offset Current IOS 0.35 5 µA
Differential (-10mV ≤ VIN ≤ +10mV) 12k
Input Resistance RIN Ω
Common mode (VEE + 2.5V ≤ VCM ≤ VCC - 0.9V) 1M
Common-Mode Rejection Ratio CMRR VEE + 2.5V ≤ VCM ≤ VCC - 0.9V 100 120 dB
VEE + 2.5 ≤ VOUT ≤ VCC - 0.9V;
115 125
RL = 10kΩ to ground
Open-Loop Gain AVOL dB
VEE + 2.5 ≤ VOUT ≤ VCC - 0.9V;
110 125
RL = 500Ω to ground

VEE + VCC -
RL = 10kΩ to ground
2.5 0.25
Output Voltage Swing VOUT V
VEE + VCC -
RL = 500Ω to ground
2.6 0.6
Output Current IOUT RL = 20Ω to ground ±30 ±60 mA
Output Short-Circuit Current ISC Sinking or sourcing ±100 mA
PSRR- VEE = -5.5V to -4.5V
Power-Supply Rejection Ratio 75 95 dB
PSRR+ VCC = +4.5V to +5.5V
Operating Supply Voltage Range VS Guaranteed by PSRR test ±4.5 ±5.5 V
Quiescent Supply Current
IS 11 13.5 mA
(per amplifier)

2 _______________________________________________________________________________________
 Dual-Supply, 180MHz, 16-Bit Accurate,
Ultra-Low Distortion Op Amps
AC ELECTRICAL CHARACTERISTICS

MAX4430–MAX4433
(VCC = +5V, VEE = -5V, RL = 500Ω, VCM = 0, AVCL = +1, TA = +25°C, unless otherwise noted.)

PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS

VOUT = 100mVp-p,
180
MAX4430/MAX4432
Small-Signal -3dB Bandwidth BWSS MHz
VOUT = 100mVp-p,
215
MAX4431/MAX4433 (AVCL = +2)
VOUT = 1Vp-p,
45
MAX4430/MAX4432
VOUT = 2Vp-p,
32
MAX4430/MAX4432
Large-Signal -3dB Bandwidth BWLS MHz
VOUT = 2Vp-p,
40
MAX4431/MAX4433 (AVCL = +2)
VOUT = 4Vp-p,
20
MAX4431/MAX4433 (AVCL = +2)
VOUT = 100mVp-p,
12
MAX4430/MAX4432
Bandwidth for 0.1dB Flatness BW0.1dB MHz
VOUT = 100mVp-p,
80
MAX4431/MAX4433 (AVCL = +2)
VOUT = 2V step,
100
MAX4430/MAX4432
Slew Rate SR V/µs
VOUT = 2V step,
145
MAX4431/MAX4433 (AVCL = +2)
VOUT = 2V step 20
Rise/Fall Time tR, tF ns
VOUT = 4V step 40
VOUT = 0 to 2V step,
37
MAX4430/MAX4432
VOUT = 0 to 2V step,
63
Settling Time to 16 Bit MAX4431/MAX4433 (AVCL = +2)
tS ns
(0.0015%) VOUT = 0 to 4V step,
56
MAX4430/MAX4432
VOUT = 0 to 4V step,
140
MAX4431/MAX4433 (AVCL = +2)

_______________________________________________________________________________________ 3
 Dual-Supply, 180MHz, 16-Bit Accurate,
Ultra-Low Distortion Op Amps
AC ELECTRICAL CHARACTERISTICS (continued)
MAX4430–MAX4433

(VCC = +5V, VEE = -5V, RL = 500Ω, VCM = 0, AVCL = +1, TA = +25°C, unless otherwise noted.)

PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS

Output “Glitch” Settling to
5pF load; CL charged from 0 to 4V 24 ns
16-Bit (0.0015%)
Output Overload Recovery Time 50% overdrive, settling to 10% accuracy 95 ns
AC Common-Mode Rejection
f = 100kHz -84 dB
Ratio
AC Power-Supply Rejection Ratio f = 100kHz -77 dB
VOUT = 2Vp-p centered at 0V,
-110
fC = 100kHz
VOUT = 2Vp-p centered at 0V,
-105
fC = 1MHz
VOUT = 4Vp-p centered at 0V,
-105
fC = 100kHz
VOUT = 4Vp-p centered at 0V,
-103
fC = 1MHz
VOUT = 2Vp-p centered at 1V,
-112
Spurious-Free fC = 100kHz
SFDR dBc
Dynamic Range VOUT = 2Vp-p centered at 1V,
-107
fC = 1MHz
VOUT = 4Vp-p centered at 2V,
-106
fC = 100kHz
VOUT = 4Vp-p centered at 2V,
-100
fC = 1MHz
VOUT = 4Vp-p centered at 2V,
-99
fC = 1MHz (RL = 1kΩ)
VOUT = 4Vp-p centered at 2V,
-100
fC = 1MHz (RL = 10kΩ)
Input Noise Voltage Density en f = 100kHz 2.8 nV/√Hz
Input Noise Current Density in f = 100kHz 1.8 pA/√Hz
Input Capacitance CIN 2.5 pF
Maximum Capacitive Load
47 pF
Without Sustained Oscillations
Output Impedance ZOUT f = 1MHz 0.2 Ω
Crosstalk MAX4432/MAX4433 fC = 1MHz -125 dB

Note 2: All devices are 100% production tested at TA = +25°C. All temperature limits are guaranteed by design.

4 _______________________________________________________________________________________
 Dual-Supply, 180MHz, 16-Bit Accurate,
Ultra-Low Distortion Op Amps
Typical Operating Characteristics

MAX4430–MAX4433
(VCC = +5V, VEE = -5V, RL = 500Ω, CL = 0pF, TA = +25°C, unless otherwise noted.)

MAX4430/MAX4432 MAX4431/MAX4433 MAX4430/MAX4432

SMALL-SIGNAL GAIN vs. FREQUENCY SMALL-SIGNAL GAIN vs. FREQUENCY GAIN FLATNESS vs. FREQUENCY
(AVCL = +1V/V) (AVCL = +2V/V) (AVCL = +1V/V)
4 4 1.0

MAX4430 toc03
MAX4430 toc02
MAX4430 toc01
100mVp-p 100mVp-p 100mVp-p
3 3 0.8
2 2 0.6
1 1 0.4
0 0 0.2

GAIN (dB)
GAIN (dB)
GAIN (dB)

-1 -1 0
-2 -2 -0.2
-3 -3 -0.4
-4 -4 -0.6
-5 -5 -0.8
-6 -6 -1.0
1M 10M 100M 1G 1M 10M 100M 1G 1M 10M 100M 1G
FREQUENCY (Hz) FREQUENCY (Hz) FREQUENCY (Hz)
MAX4431/MAX4433 MAX4430/MAX4432 MAX4431/MAX4433
GAIN FLATNESS vs. FREQUENCY LARGE-SIGNAL GAIN vs. FREQUENCY LARGE-SIGNAL GAIN vs. FREQUENCY
(AVCL = +2V/V) (AVCL = +1V/V) (AVCL = +2V/V)
0.5 4 4
MAX4430 toc05

MAX4430 toc06
MAX4430 toc04

100mVp-p 1Vp-p 1Vp-p

0.4 3 3
0.3 2 2
0.2 1 1
0.1 0 0
GAIN (dB)
GAIN (dB)
GAIN (dB)

0 -1 -1
-0.1 -2 -2
-0.2 -3 -3
-0.3 -4 -4
-0.4 -5 -5

-0.5 -6 -6
1M 10M 100M 1G 1M 10M 100M 1G 1M 10M 100M 1G
FREQUENCY (Hz) FREQUENCY (Hz) FREQUENCY (Hz)

MAX4430/MAX4432 MAX4431/MAX4433 MAX4430/MAX4432

SMALL-SIGNAL PULSE RESPONSE SMALL-SIGNAL PULSE RESPONSE LARGE-SIGNAL PULSE RESPONSE
MAX4430 toc09
MAX4430 toc07

MAX4430 toc08

AVCL = +1V/V AVCL = +2V/V AVCL = +1V/V

INPUT INPUT INPUT

50mV/div 25mV/div 500mV/V

OUTPUT OUTPUT OUTPUT

50mV/div 50mV/div 500mV/div

10ns/div 10ns/div 10ns/div

_______________________________________________________________________________________ 5
 Dual-Supply, 180MHz, 16-Bit Accurate,
Ultra-Low Distortion Op Amps
MAX4430–MAX4433

Typical Operating Characteristics (continued)

(VCC = +5V, VEE = -5V, RL = 500Ω, CL = 0pF, TA = +25°C, unless otherwise noted.)

MAX4431/MAX4433 MAX4430/MAX4432 MAX4431/MAX4433

LARGE-SIGNAL PULSE RESPONSE SMALL-SIGNAL PULSE RESPONSE SMALL-SIGNAL PULSE RESPONSE

MAX4430toc12
MAX4430 toc10

MAX4430 toc11
AVCL = +2V/V AVCL = +1V/V AVCL = +1V/V
CL = 10pF CL = 15pF
INPUT INPUT INPUT
250mV/div 50mV/V 25mV/div

OUTPUT OUTPUT OUTPUT

500mV/div 50mV/div 50mV/div

10ns/div 10ns/div 10ns/div

MAX4430/MAX4432 MAX4431/MAX4433 POWER-SUPPLY REJECTION RATIO

LARGE-SIGNAL PULSE RESPONSE LARGE-SIGNAL PULSE RESPONSE vs. FREQUENCY
0
MAX4430 toc14
MAX4430 toc13

MAX4430 toc15
AVCL = +1V/V AVCL = +1V/V
CL = 20pF CL = 30pF POWER-SUPPLY REJECTION (dB) -10
INPUT INPUT -20
500mV/div 250mV/div
-30
-40
-50
-60
OUTPUT OUTPUT -70
500mV/div 500mV/div
-80
-90
-100
10ns/div 10ns/div 0.1 1 10 100
FREQUENCY (MHz)

COMMON-MODE REJECTION RATIO OUTPUT ISOLATION RESISTANCE CLOSED-LOOP OUTPUT IMPEDANCE

vs. FREQUENCY vs. CAPACITIVE LOAD vs. FREQUENCY
0 12 100
MAX4430 toc17
MAX4430 toc16

MAX4430 toc18

-10
OUTPUT ISOLATION RESISTANCE (Ω)
COMMON-MODE REJECTION (dB)

-20 10
MAX4430 10
OUTPUT IMPEDANCE (Ω)

-30
8
-40
-50 6 1
MAX4431
-60
4
-70
0.1
-80
2
-90
-100 0 0.01
0.1 1 10 100 0 25 50 75 100 125 150 175 200 0.1 1 10 100 1000
FREQUENCY (MHz) CAPACITIVE LOAD (pF) FREQUENCY (MHz)

6 _______________________________________________________________________________________
 Dual-Supply, 180MHz, 16-Bit Accurate,
Ultra-Low Distortion Op Amps
Typical Operating Characteristics (continued)

MAX4430–MAX4433
(VCC = +5V, VEE = -5V, RL = 500Ω, CL = 0pF, TA = +25°C, unless otherwise noted.)

MAX4430 HARMONIC DISTORTION HARMONIC DISTORTION

GAIN AND PHASE vs. FREQUENCY vs. FREQUENCY vs. OUTPUT SWING
MAX4430 toc19
120 135 0 0

MAX4430 toc20

MAX4430 toc21
AV = 1000 -10 VOUT = 2Vp-p f = 1MHz
-10
80 90 -20 -20
-30 -30
HARMONIC DISTORTION (dB)

HARMONIC DISTORTION (dB)

40 GAIN 45 -40 -40
-50 -50
0 0 -60 -60
GAIN (dB)

PHASE (°)

-45 -70 -70

-40
PHASE -80 2ND HARMONIC -80
-80 -90 -90 -90 2ND HARMONIC
-100 -100
-120 -135
-110 -110
-120 3RD HARMONIC -120 3RD HARMONIC
-160 -180
-130 -130
-200 -225 -140 -140
0.1 1 10 100 1000 0.1 1 10 100 0 1 2 3 4 5 6
FREQUENCY (MHz) FREQUENCY (MHz) OUTPUT SWING (Vp-p)

HARMONIC DISTORTION INPUT VOLTAGE NOISE QUIESCENT CURRENT PER AMPLIFIER

vs. RESISTIVE LOAD vs. FREQUENCY vs. TEMPERATURE
0 1000 MAX4430 toc23
12.0

MAX4430 toc24
MAX4430 toc22

-10 f = 1MHz
-20
-30 11.5
HARMONIC DISTORTION (dB)

QUIESCENT CURRENT (mA)

VOLTAGE NOISE (nV/√Hz)

-40
-50 100 11.0
-60
-70
10.5
-80
-90 10
2ND HARMONIC 10.0
-100
-110
-120 3RD HARMONIC 9.5
-130
-140 1 9.0
0 200 400 600 800 1000 1 10 100 1k 10k 100k 1M 10M -50 -25 0 25 50 75 100
RESISTIVE LOAD (Ω) FREQUENCY (Hz) TEMPERATURE (°C)

INPUT BIAS CURRENT OFFSET VOLTAGE VOLTAGE SWING

vs. TEMPERATURE vs. TEMPERATURE vs. TEMPERATURE
12.0 3.0 3.0
MAX4430 toc26

MAX4430 toc27
MAX4430 toc25

2.5
11.5 2.0 2.5
QUIESCENT CURRENT (µA)

1.5 VOS+
OFFSET VOLTAGE (mV)

VOLTAGE SWING (V)

11.0 1.0 2.0

FROM NEGATIVE RAIL
0.5
10.5 0 1.5
-0.5
10.0 -1.0 1.0
-1.5 VOS-

9.5 -2.0 0.5 FROM POSITIVE RAIL

-2.5
9.0 -3.0 0
-50 -25 0 25 50 75 100 -50 -25 0 25 50 75 100 -50 -25 0 25 50 75 100
TEMPERATURE (°C) TEMPERATURE (°C) TEMPERATURE (°C)

_______________________________________________________________________________________ 7
 Dual-Supply, 180MHz, 16-Bit Accurate,
Ultra-Low Distortion Op Amps
MAX4430–MAX4433

Typical Operating Characteristics (continued)

(VCC = +5V, VEE = -5V, RL = 500Ω, CL = 0pF, TA = +25°C, unless otherwise noted.)
VOLTAGE SWING MAX4432/MAX4433
vs. TEMPERATURE CROSSTALK vs. FREQUENCY
3.0 0

MAX4430 toc29
MAX4430 toc28
RL = 10kΩ
-20
2.5

-40
VOLTAGE SWING (V)

2.0
FROM NEGATIVE RAIL

GAIN (dB)
-60
1.5
-80
1.0
-100

0.5 -120
FROM POSITIVE RAIL
0 -140
-50 -25 0 25 50 75 100 0.1 1 10 100 1000
TEMPERATURE (°C) FREQUENCY (MHz)

Pin Description
PIN

MAX4430/MAX4431 NAME FUNCTION

5 SOT23 8 SO
1 6 OUT Output

2 4 VEE Negative Power Supply

3 3 IN+ Noninverting Input

4 2 IN- Inverting Input

5 7 VCC Positive Power Supply

— 1, 5, 8 N.C. No Connection. Not internally connected.

PIN

MAX4432/MAX4433 NAME FUNCTION

8 SO/8 µMAX

1 OUTA Amplifier A Output

2 INA- Amplifier A Inverting Input

3 INA+ Amplifier A Noninverting Input

4 VEE Negative Power Supply

5 INB+ Amplifier B Noninverting Input

6 INB- Amplifier B Inverting Input

7 OUTB Amplifier B Output

8 VCC Positive Power Supply

8 _______________________________________________________________________________________
 Dual-Supply, 180MHz, 16-Bit Accurate,
Ultra-Low Distortion Op Amps
Detailed Description and 2 for the MAX4431/MAX4433. Use care in selecting

MAX4430–MAX4433
the value for the resistor marked RS in both circuits.
The MAX4430–MAX4433 are wide-bandwidth, ultra-low-
From dynamic stability considerations (based on the
distortion, voltage-feedback amplifiers. The MAX4430/
part’s frequency response and the input capacitance of
MAX4432 are internally compensated for unity gain.
the MAX4430–MAX4433), the maximum recommended
The MAX4431/MAX4433 are internally compensated for
value for RS is 500Ω. In general, lower RS values will
gains of +2V/V or greater.
yield a higher bandwidth and better dynamic stability,
These amplifiers have ultra-fast 37ns (MAX4430/ at the cost of higher power consumption, higher power
MAX4432) 16-bit settling times, 100dB SFDR at 1MHz, dissipation in the IC, and reduced output drive avail-
and 4Vp-p output swing with minimum 110dB open- ability. For a minimum RS value, take into consideration
loop gain. that the current indicated as IF is supplied by the output
stage and must be discounted from the maximum out-
High-Speed ADC Input Driver Application put current to calculate the maximum current available
The MAX4430–MAX4433 op amps are ideal for driving to the load. IF can be found using the following equa-
high-speed 14- to 16-bit ADCs. In most cases, these tion:
ADCs operate with a charge balance scheme, with
capacitive loads internally switched on and off from the IF = VIN(MAX) / RS
input. The driver used must withstand these changing If DC thermal stability is an important design concern,
capacitive loads while holding the signal amplitude sta- the Thevenin resistance seen by both inputs at DC
bility consistent with the ADC’s resolution and, at the must be balanced. This includes the resistance of the
same time, have a frequency response compatible with signal source and termination resistors if the amplifier
the sampling speed of the ADC (Figure 1). signal input is fed from a transmission line. The capaci-
tance associated with the feedback resistors must also
Inverting and Noninverting Configurations be considered as a possible limitation to the available
The circuits typically used for the inverting and non- bandwidth or to the dynamic stability. Only resistors
inverting configurations of the MAX4430–MAX4433 are with small parallel capacitance specifications should
shown in Figures 2a and 2b. The minimum uncondition- be considered.
ally stable gain values are 1 for the MAX4430/MAX4432
Applications Information
Layout and Power-Supply Bypassing
The MAX4430–MAX4433 have wide bandwidth and
+VCC consequently require careful board layout. To realize
the full AC performance of these high-speed amplifiers,
HIGH-SPEED pay careful attention to power-supply bypassing and
14/16-BIT ADC
board layout. The PC board should have a large low-
-VEE impedance ground plane that is as free of voids as
possible. Do not use commercial breadboards. Keep
signal lines as short and straight as possible. Observe
high-frequency bypassing techniques to maintain the
Figure 1. Typical Application Circuit

RF
VIN
RS
VOUT VIN IF

IF R V
A = 1 + F = OUT VOUT
RS VIN
- RF V
A= = OUT
RS VIN
RS RF
RB

Figure 2a. Noninverting Configuration Figure 2b. Inverting Configuration

_______________________________________________________________________________________ 9
 Dual-Supply, 180MHz, 16-Bit Accurate,
Ultra-Low Distortion Op Amps
MAX4430–MAX4433

Ordering Information (continued)

PART TEMP. RANGE PIN-PACKAGE
o o
MAX4431EUK-T -40 C to +85 C 5 SOT23-5
MAX4431ESA -40oC to +85oC 8 SO
RISO MAX4432EUA -40oC to +85oC 8 µMAX
VOUT o o
MAX4432ESA -40 C to +85 C 8 SO
VIN CL RL MAX4433EUA -40oC to +85oC 8 µMAX
MAX4433ESA -40oC to +85oC 8 SO

Pin Configurations (continued)

MAX4430
TOP VIEW
MAX4430
MAX4431
N.C. 1 8 N.C.
Figure 3. Capacitive-Load Driving Circuit IN- 2 7 VCC

IN+ 3 6 OUT
amplifier’s accuracy and stability. In general, use sur-
VEE 4 5 N.C.
face-mount components since they have shorter bodies
and lower parasitic reactance. This will result in
SO
improved performance over through-hole components.
The bypass capacitors should include 1nF and/or MAX4432
0.1µF surface-mount ceramic capacitors between each MAX4433
OUTA 1 8 VCC
supply pin and the ground plane, located as close to
the package as possible. Place a 10µF tantalum INA- 2 7 OUTB
capacitor at the power supply’s point of entry to the PC INA+ 3 6 INB-
board to ensure the integrity of the incoming supplies.
Input termination resistors and output back-termination VEE 4 5 INB+
resistors, if used, should be surface-mount types and
should be placed as close to the IC pins as possible. µMAX/SO

Driving Capacitive Loads

MAX4430–MAX4433 can drive capacitive loads. Chip Information
However, excessive capacitive loads may cause ring-
ing or instability at the output as phase margin is TRANSISTOR COUNT: MAX4430/MAX4431: 103
reduced. Adding a small isolation resistor in series with MAX4432/MAX4433: 248
the output capacitive load helps reduce the ringing but
slightly increases gain error (see Typical Operating
Characteristics and Figure 3).

10 ______________________________________________________________________________________
 Dual-Supply, 180MHz, 16-Bit Accurate,
Ultra-Low Distortion Op Amps
Package Information

MAX4430–MAX4433
SOT5L.EPS
8LUMAXD.EPS

______________________________________________________________________________________ 11
 Dual-Supply, 180MHz, 16-Bit Accurate,
Ultra-Low Distortion Op Amps
Package Information (continued)
MAX4430–MAX4433

SOICN.EPS

Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.

12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600

© 2000 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.