MAX5X02 Evaluation Kit Evaluates: MAX5700/MAX5701/MAX5702A /B/

MAX5800/MAX5801/MAX5802A/B

General Description Features

The MAX5X02 evaluation kit (EV kit) demonstrates the ● 2.7V to 5.5V Wide Input Supply Range
MAX5702 and MAX5802 12-bit, 2-channel, low-power ● Demonstrates 4.5µs Settling Time of Buffered Output
DACs with internal reference and buffered voltage out-
puts. The EV kit provides controls to change the DAC ● High Precision with ±1 LSB INL
outputs, power operations, and references. ● 1kΩ, 100kΩ, or High-Z Selectable Output Termination
The DAC ICs are controlled by an on-board MAXQ® ● 2.048V, 2.500V, and 4.096V Precision 10ppm (max)
microcontroller that provides two different selectable inter- Selectable Internal References
face options: I2C and SPI. The EV kit features Windows ● Demonstrates User-Supplied External Reference
XP®-, Windows Vista®-, and Windows® 7-compatible
● Supports Entire Family of I2C and
software that provides a simple graphical-user interface
SPI 12-/10-/8-Bit DACs
(GUI) for exercising the features of the ICs.
● Windows XP-, Windows Vista-, and Windows
The EV kit comes with the MAX5702AAUB+ (SPI) and
7-Compatible Software
the MAX5802AAUB+ (I2C) installed. Contact the factory
for samples of the pin-compatible MAX5700AUB+ (SPI, ● USB-Powered (Cable Included)
8-bit), MAX5701AUB+ (SPI, 10-bit), MAX5702BAUB+ ● Fully Assembled and Tested with Proven PCB Layout
(SPI, 12-bit), MAX5800AUB+ (I2C, 8-bit), MAX5801AUB+
(I2C, 10-bit), MAX5802BAUB+ (I2C, 12-bit) versions.
Ordering Information appears at end of data sheet.

Component List
DESIGNATION QTY DESCRIPTION DESIGNATION QTY DESCRIPTION

ADDR, CSB, C2, C5,

0.1µF ±10%, 16V X7R ceramic
DIN, SDA, SCL, C12–C14, C18,
10 capacitors (0603)
SCLK, C23, C25,
Murata GRM188R71C104K
U1_REF, C27, C29
U1_CLR, C3, C11, C17, Not installed, ceramic capacitors
U1_OUTA, 0
16 Red test points C30, C31 (0603)
U1_OUTB,
U2_OUTA, 100pF ±5%, 50V C0G ceramic
U2_OUTB, C4, C10 2 capacitors (0603)
U2_REF, Murata GQM1885C1H101J
U2_CLR, VDD, 18pF ±5%, 50V C0G ceramic
VDDIO C15, C16 2 capacitors (0603)
Murata GRM1885C1H180J
AGND (x6),
8 Black test points
DGND (x2) H1 0 Not installed, 4-pin header
C1, C6–C9, 1µF ±10%, 16V X7R ceramic H2 0 Not installed, 10-pin (2 x 5) header
C19–C22, C24, 12 capacitors (0603) JU1, JU2,
C28, C32 Murata GRM188R71C105K 7 2-pin headers
JU7–JU11
JU3–JU6 4 3-pin headers
MAXQ is a registered trademark of Maxim Integrated Products,
Inc. JU_ID0–
0 Not installed, 2-pin headers
Windows, Windows XP, and Windows Vista are registered JU_ID3
trademarks and registered service marks of Microsoft Corporation.

19-6710; Rev 0; 5/13

MAX5X02 Evaluation Kit Evaluates: MAX5700/MAX5701/MAX5702A /B/
MAX5800/MAX5801/MAX5802A /B

Component List (continued)

DESIGNATION QTY DESCRIPTION DESIGNATION QTY DESCRIPTION
Ferrite bead (0603) Level translators (10 µMAX)
L1 1 U4, U6 2
TDK MMZ1608R301A Maxim MAX1840EUB+
R1, R2 2 4.7kΩ ±5% resistors (0603) ESD protector
U5 0
R3, R15, R16 3 1MΩ ±5% resistors (0603) Not Installed (6 SOT23)

R4–R6 3 1.5kΩ ±5% resistors (0603) 3.3V LDO (5 SC70)

U7 1
Maxim MAX8511EXK33+
R8 1 100Ω ±5% resistor (0603)
Microcontroller (64 LQFP)
R9 1 10kΩ ±5% resistor (0603) U8 1
Maxim MAXQ622G-0000+
12-bit 2-channel DAC (10 µMAX®)
U1 1 Mini-USA type-B right-angle
Maxim MAX5802AAUB+ USB1 1
PC-mount receptacle
12-bit 2-channel DAC (10 µMAX)
U2 1 Y1 1 12MHz crystal (HCM49)
Maxim MAX5702AAUB+
— 1 USB high-speed A-to-B cables, 6ft
2.5 voltage reference (8 SO)
U3 1 — 11 Shunts
Maxim MAX6071BAUT25+
— 1 PCB: MAX5X02 EVKIT

Component Suppliers
SUPPLIER PHONE WEBSITE
Murata Americas 800-241-6574 www.murataamericas.com
TDK Corp. 847-803-6100 www.component.tdk.com
Note: Indicate that you are using the MAX5X02 when contacting these suppliers.

MAX5X02 EV Kit Files

FILES DESCRIPTION
INSTALL.EXE Installs the EV kit files on your computer
MAX5X02Vxx.EXE Application program
USBConverterDLL.DLL Application library
UNINSTALL.EXE Uninstalls the EV kit software

µMAX is a registered trademark of Maxim Integrated Products,

Inc.

www.maximintegrated.com Maxim Integrated │ 2

MAX5X02 Evaluation Kit Evaluates: MAX5700/MAX5701/MAX5702A /B/
MAX5800/MAX5801/MAX5802A /B

Quick Start MAX5X02GUISetupVxx.ZIP. Save the EV kit soft-

ware to a temporary folder and uncompress the ZIP
Required Equipment file.
● MAX5X02 EV kit (USB cable included)
5) Install the EV kit software on your computer by run-
● Windows XP, Windows Vista, or Windows 7 PC with ning the INSTALL.EXE program inside the temporary
a spare USB port folder. The program files are copied to your PC and
● Two digital voltmeters (DVMs) icons are created in the Windows Start | Programs
menu.
Note: In the following sections, software-related items are
identified by bolding. Text in bold refers to items directly 6) Connect the USB cable from the PC to the EV kit
from the EV kit software. Text in bold and underlined board; the USB driver is installed automatically.
refers to items from the Windows operating system. 7) Start the EV kit software by opening its icon in the
Start | Programs menu. The EV kit software main
Procedure
window appears, as shown in Figure 1.
The EV kit is fully assembled and tested. Follow the steps
below to verify board operation: 8) Within the DACs tab in the Data edit box, enter
0xFFF and select the command Write CODE and
1) Verify that jumpers JU1–JU11 are in their default LOAD reg A within the same row. Press the Execute
position, as shown in Table 1. button on the right.
2) Connect the positive terminal of DVM #1 to 9) Verify that DVM #1 measures 2.500V.
U2_OUTA and connect the negative terminal to near-
est the AGND test point. 10) Select the I2C radio button in the Interface group
box and the GUI automatically detects the I2C
3) Connect the positive terminal of DVM #2 to address. See Figure 2.
U1_OUTA and connect the negative terminal to the
nearest AGND test point. 11) Move jumper JU4 to the 1-2 position.

4) Visit www.maximintegrated.com/evkitsoftware to 12) Press the Execute button on the same row again.
download the latest version of the EV kit software, 13) Verify that DVM #2 measures 2.500V.

www.maximintegrated.com Maxim Integrated │ 3

MAX5X02 Evaluation Kit Evaluates: MAX5700/MAX5701/MAX5702A /B/
MAX5800/MAX5801/MAX5802A /B

Figure 1. MAX5X02 EV Kit Software Main Window (SPI)

www.maximintegrated.com Maxim Integrated │ 4

MAX5X02 Evaluation Kit Evaluates: MAX5700/MAX5701/MAX5702A /B/
MAX5800/MAX5801/MAX5802A /B

Figure 2. MAX5X02 EV Kit Software Main Window (I2C)

www.maximintegrated.com Maxim Integrated │ 5

MAX5X02 Evaluation Kit Evaluates: MAX5700/MAX5701/MAX5702A /B/
MAX5800/MAX5801/MAX5802A /B

Detailed Description of Software a list of possible commands. If a sequence of com-

The MAX5X02 EV kit software can evaluate all I2C mands need to be performed, adjust all Data edit boxes
and SPI interface family of devices. In addition to the and Commands drop-down lists accordingly, and press
interfaces, the software allows 12-/10-/8-bit DAC part the Execute All button. To reset the Script Status to
selection. The main software window has two tabs, Incomplete, press the Reset Script button.
DACs and Controls. Within the DACs tab, the user can Data Logging
send a sequence of write commands to the two DACs,
Using the Save To File button, the sequence of the
assert CLR, and load and save the write sequence. The
commands can be saved into a text file. To recall the
Controls tab (Figure 3) allows the user to change the
sequence, press the Load From File button and select
power, configuration, and reference.
the appropriate text file.
Part Selection DAC Outputs (I2C Only)
On the upper left corner is a Part Selection group box.
Press the Read Back button and the CODE and voltages
The user must select the appropriate radio button that
of the DACs are displayed within the DAC Outputs group
corresponds to the installed Maxim IC DAC resolution
box.
(number of bits).
Asynchronous CLR
Interface
A checked CLR checkbox drives the CLR pin of the
The Interface group box allows the user to toggle
MAX5702 or MAX5802 low, which allows the changes
between I2C and SPI DAC parts. By default, the software
to the CODE register to change the DAC outputs.
is configured to communicate using the SPI interface first.
Unchecking the CLR Asserted checkbox drives the CLR
Once the I2C radio button selection is made, the software
pin of the MAX5702 or MAX5802 high. To change the
automatically detects the correct I2C address from the
DAC outputs, the user must write to the CODE registers,
drop-down list and the user is allowed to communicate
and then write to the DAC registers.
using the I2C interface. See Table 2 for a list of the I2C
addresses. Power
DAC Commands The power command is selectable for individual DACs.
When a DAC is selected, the channel is active. Other
Enter the desired Data on the left and choose the appro-
options include powering down with 1kΩ termination
priate Command from the drop-down list. Pressing the
to GND, 100kΩ termination to GND, and high imped-
Execute button writes to the CODE and/or DAC regis-
ance. Once the appropriate selection is made, press the
ters and the Script Status changes from Incomplete to
Execute button. A Read Back button is available for the
Complete. Refer to the MAX5700/MAX5701/MAX5702
I2C interface.
and MAX5800/MAX5801/MAX5802 IC data sheets for

www.maximintegrated.com Maxim Integrated │ 6

MAX5X02 Evaluation Kit Evaluates: MAX5700/MAX5701/MAX5702A /B/
MAX5800/MAX5801/MAX5802A /B

Figure 3. MAX5X02 EV Kit Software Main Window (SPI Controls Tab)

www.maximintegrated.com Maxim Integrated │ 7

MAX5X02 Evaluation Kit Evaluates: MAX5700/MAX5701/MAX5702A /B/
MAX5800/MAX5801/MAX5802A /B

Figure 4. MAX5X02 EV Kit Software Main Window (I2C Controls Tab)

www.maximintegrated.com Maxim Integrated │ 8

MAX5X02 Evaluation Kit Evaluates: MAX5700/MAX5701/MAX5702A /B/
MAX5800/MAX5801/MAX5802A /B

Configuration LDAC SW Clear

The LDAC Enabled checkbox is selectable for individual Press the SW Clear button to return all CODE and DAC
DACs. When the DAC is selected, the channel allows the registers to their default values, and the registers are
user to change the DAC’s output by writing to the CODE cleared.
register. Once the appropriate selection is made, press
the Execute button. Multiple EV Kits
The software can communicate to multiple MAX5X02 EV
Reference kits connected to the USB ports of the PC. The status
The reference default configuration is set to 2.5V bar at the bottom of the GUI shows the number of boards
using the on-board voltage-reference IC (U3). A new that are connected. If all boards connected to the PC are
reference voltage can be entered into the REF edit box, not connected to the GUI, click the Options | Connect
but the user must apply the same voltage at the board for menu item and the status bar should be updated. Use the
proper operation. Other reference options include 2.048V, Board Index drop-down list to select the appropriate EV
2.500V, and 4.096V through software commands. Make kit for communications.
sure the VDD supply is greater or equal to the voltage
reference selected for proper operation. Once the Detailed Description of Hardware
appropriate selection is made, press the Execute button. The MAX5X02 EV kit provides a proven layout for the
A Read Back button is available for the I2C interface. MAX5702 and the MAX5802. An on-board MAXQ622
microcontroller and jumpers to disconnect the on-board
SW Reset
microcontroller are included on the EV kit.
Press the SW Reset button to reset all CODE, DAC, and
configuration registers to their default settings.

Table 1. EV Kit Jumper Settings

JUMPER SHUNT POSITION DESCRIPTION
Installed* Connects the SDA signal of the on-board microcontroller to the SDA pin of IC U1.
JU1
Not installed Disconnects the SDA signal of the on-board microcontroller to the SDA pin of IC U1.
Installed* Connects SCL signal of in-board microcontroller to the SCL pin of IC U1.
JU2
Not installed Disconnects the SCL signal of the on-board microcontroller to the SCL pin of IC U1.
1-2* Connects the ADDR pin of IC U1 to VDDIO to determine the I2C address (see Table 2).
JU3 2-3 Connects the ADDR pin of IC U1 to DGND to determine the I2C address (see Table 2).
Not installed ADDR pin of IC U1 is not connected to determine the I2C address (see Table 2).
1-2 Connects on-board voltage reference IC (U3) to the REF pin of IC U1.
2-3* Connects on-board voltage reference IC (U3) to the REF pin of IC U2.
JU4
User-supplied REF. The user must apply a voltage reference at the U1_REF and/or U2_REF
Not installed
test point(s).
1-2* Connects the VDDIO pins of IC U1 and U2 to the on-board 3.3V supply.
JU5 2-3 Connects the VDDIO pins of IC U1 and U2 to the on-board 5V USB supply.
Not installed User-supplied VDDIO. The user must apply a voltage between 1.8V to 5.5V at the VDDIO test point.
1-2* Connects the VDD pins of IC U1 and U2 to the on-board 3.3V supply
JU6 2-3 Connects the VDD pins of IC U1 and U2 to the on-board 5V USB supply.
Not installed User-supplied VDD. The user must apply a voltage between 2.7V to 5.5V at the VDD test point.
Installed* Connects the DIN signal of the on-board microcontroller to the DIN pin of IC U2.
JU7
Not installed Disconnects the DIN signal of the on-board microcontroller to the DIN pin of IC U2.

www.maximintegrated.com Maxim Integrated │ 9

MAX5X02 Evaluation Kit Evaluates: MAX5700/MAX5701/MAX5702A /B/
MAX5800/MAX5801/MAX5802A /B

Table 1. EV Kit Jumper Settings (continued)

JUMPER SHUNT POSITION DESCRIPTION
Installed* Connects the SCLK signal of the on-board microcontroller to the SCLK pin of IC U2.
JU8
Not installed Disconnects the SCLK signal of the on-board microcontroller to the SCLK pin of IC U2.
Installed* Connects the CSB signal of the on-board microcontroller to the CSB pin of IC U2.
JU9
Not installed Disconnects the CSB signal of the on-board microcontroller to the CSB pin of IC U2.
Installed Connects the CLR signal of the on-board microcontroller to the CLR pin of IC U1.
JU10
Not installed* Disconnects the CLR signal of the on-board microcontroller to the CLR pin of IC U1.
Installed* Connects the CLR signal of the on-board microcontroller to the CLR pin of IC U2.
JU11
Not installed Disconnects the CLR signal of the on-board microcontroller to the CLR pin of IC U2.
*Default position.

I2C Address Table 2. I2C Address Setting (JU3)

The I2C address of the MAX5802 is determined by the
SHUNT POSITION MAX5802 ADDRESS (hex)
shunt setting of jumper JU3. See Table 2 for all possible
hexadecimal addresses. (ADDR) WRITE READ
1-2* 0x18 0x19
User-Supplied Power Supply
2-3 0x1C 0x1D
The EV kit is powered completely from the USB port by
default. To power the MAX5702 and MAX5802 with a Not installed 0x1E 0x1F
user-supplied power supply, remove the shunt on jumper *Default position.
JU6 and apply a 2.7V to 5.5V power supply at the VDD
test point and the nearest AGND test point on the EV kit. User-Supplied I2C
A user-supplied VDDIO power supply can also be used by To evaluate the EV kit with a user-supplied I2C bus,
removing the shunt on jumper JU5 and applying 1.8V to remove shunts from jumpers JU1–JU3. Apply the user-
5.5V to the VDDIO test point and the nearest AGND test supplied I2C signals to the SCL and SDA test points and
point on the EV kit. use the nearest DGND test point for the return ground
on the EV kit. If pullup resistors are on the user-supplied
User-Supplied Reference interface, resistors R1 and R2 should be removed. Apply
The user can apply a user-supplied voltage reference by appropriate signal to the ADDR test point to determine the
removing the shunt on jumper JU4 and applying 1.24V to I2C address.
VDD at the U1_REF and/or U2_REF test points on the
EV kit. User-Supplied CLR
A user-supplied CLR signal can be used by removing the
User-Supplied SPI shunts from jumper JU10 and/or JU11. Apply the user-
To evaluate the EV kit with a user-supplied SPI bus, supplied CLR signal to U1_CLR for the MAX5802 and/or
remove shunts from jumpers JU7–JU9. Apply the user- U2_CLR for the MAX5702, and use the nearest DGND
supplied SPI signals to the DIN, SCLK, and CSB test test point for the return ground on the EV kit.
points and use the nearest DGND test point for the return
ground on the EV kit.

www.maximintegrated.com Maxim Integrated │ 10

MAX5X02 Evaluation Kit Evaluates: MAX5700/MAX5701/MAX5702A /B/
MAX5800/MAX5801/MAX5802A /B

Figure 5a. MAX5X02 EV Kit Schematic (Sheet 1 of 2)

www.maximintegrated.com Maxim Integrated │ 11

MAX5X02 Evaluation Kit Evaluates: MAX5700/MAX5701/MAX5702A /B/
MAX5800/MAX5801/MAX5802A /B

Figure 5b. MAX5X02 EV Kit Schematic (Sheet 2 of 2)

www.maximintegrated.com Maxim Integrated │ 12

MAX5X02 Evaluation Kit Evaluates: MAX5700/MAX5701/MAX5702A /B/
MAX5800/MAX5801/MAX5802A /B

1.0”

Figure 6. MAX5X02 EV Kit Component Placement Guide—Component Side

1.0”

Figure 7. MAX5X02 EV Kit PCB Layout—Component Side

www.maximintegrated.com Maxim Integrated │ 13

MAX5X02 Evaluation Kit Evaluates: MAX5700/MAX5701/MAX5702A /B/
MAX5800/MAX5801/MAX5802A /B

1.0”

Figure 8. MAX5X02 EV Kit PCB Layout—Solder Side

www.maximintegrated.com Maxim Integrated │ 14

MAX5X02 Evaluation Kit Evaluates: MAX5700/MAX5701/MAX5702A /B/
MAX5800/MAX5801/MAX5802A /B

Ordering Information
PART TYPE
MAX5X02EVKIT# EV Kit
#Denotes RoHS compliant.

www.maximintegrated.com Maxim Integrated │ 15

MAX5X02 Evaluation Kit Evaluates: MAX5700/MAX5701/MAX5702A /B/
MAX5800/MAX5801/MAX5802A /B

Revision History
REVISION REVISION PAGES
DESCRIPTION
NUMBER DATE CHANGED
0 5/13 Initial release —

For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com.

Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses
are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time.

Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc. © 2013 Maxim Integrated Products, Inc. │ 16