ORDER NO.

CPD0711216CE

Notebook Computer

Model No. CF-30FTSAZAM

This is the Service Manual for

the following areas.
M …for U.S.A. and Canada

© 2007 Matsushita Electric Industrial Co., Ltd. All rights reserved.

Unauthorized copying and distribution is a violation of law.
 WARNING
For U.K.
This apparatus must be earthed for your safety.
To ensure safe operation the three-pin plug must be inserted only into a standard three-pin power point
which is effectively earthed through the normal household wiring.
Extension cords used with the equipment must be three-core and be correctly wired to provide connec-
tion to earth. Wrongly wired extension cords are a major cause of fatalities.
The fact that the equipment operates satisfactorily does not imply that the power point is earthed and
that the installation is completely safe.
For your safety, if you have any doubt about the effective earthing of the power point, consult a quali-
fied electrician.
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY
This appliance is supplied with a moulded three pin mains plug for your safety and convenience.
A 3 amp fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 3 amps and
that it is approved by ASTA or BSI to BS 1362.

Check for the ASTA mark or the BSI mark on the body of the fuse.
If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced.
If you lose the fuse cover the plug must not be used until a replacement cover is obtained.
A replacement fuse cover can be purchased from your local Panasonic Dealer.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR
HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED
OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED
INTO ANY 13 AMP SOCKET.
If a new plug is to be fitted please observe the wiring code as shown below.
If in any doubt please consult a qualified electrician.
Warning: THIS APPLIANCE MUST BE EARTHED.
Important
The wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow: Earth
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured
markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured GREEN-and-YELLOW must be connected to the terminal in the plug
which is marked by the letter E or by the safety earth symbol coloured GREEN or GREEN-and-
YELLOW.
The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or
coloured BLACK.
The wire which is coloured Brown must be connected to the terminal which is marked with the letter L
or coloured RED.

The mains plug on this equipment must be used to disconnect the mains power.
Please ensure that a socket outlet is available near the equipment and shall be easily accessible.
How to replace the fuse
Open the fuse compartment with a screw-
driver and replace the fuse.

Warnings
This equipment is not designed for connection to an IT power system.
(An IT system is a system having no direct connections between live parts and Earth; the exposed-conducive-
parts of the electrical installation are earthed.
An IT system is not permitted where the computer is directly connected to public supply systems in the U.K.)
Disconnect the mains plug from the supply socket when the computer is not in use.

This equipment is produced to BS800/1983.

 SAFETY PRECAUTIONS
1. Before servicing, unplug the power cord to prevent an electric shock.
2. When replacing parts, use only manufacture's recommended components
for safety.
3. Check the condition of the power cord. Replace if wear or damage is evident.
4. After servicing, be sure to restore the lead dress, insulation barriers,
insulation papers, shields, etc.

Important Safety Instructions

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk
of fire, electric shock and injury to persons, including the following:
1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a
wet basement or near a swimming pool.
2. Avoid using a telephone (other than a cordless type) during an electrical storm.
There may be a remote risk of electric shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire.
They may explode. Check with local codes for possible special disposal instructions.
SAVE THESE INSTRUCTIONS

LITHIUM BATTERY
This computer contains a lithium battery to enable the date, time, and other
data to be stored. The battery should only be exchanged by authorized
service personel.
Warning! A risk of explosion from incorrect installation or misapplication may
possibly occur.

LITHIUM BATTERY
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the equipment manufacturer.
Dispose of used batteries according to the manufacturer's instructions.

LITHIUMBATTERIES
Vorsicht!
Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz nur durch denselben order einen vom
Hersteller empfohlenen ähnlichen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers.

PILE AU LITHIUM
ATTENTION: IL Y A DANGER D'EXPLOSION S' IL Y A REMPLACEMENT INCORRECT DE LA PILE.
REMPLACER UNIQUEMENT AVEC UNE PILE DU MÈME TYPE OU D'UN TYPE RECOMMANDÉ PAR LE
CONSTRUCTEUR. METTRE AU RÉBUT LES PILES USAGÉES CONFORMÉMENT AUX INSTRUCTIONS DU
FABRICANT.
Precautions (Battery Pack)

Do Not Use with Any Other Product Do not touch the terminals on the battery pack. The
The battery pack is rechargeable and was intended for battery pack may no longer function properly if the
the specified product. If it is used with a product other contacts are dirty or damaged.
than the one for which it was designed, electrolyte leak- Do not expose the battery pack to water, or allow it to
age, generation of heat, ignition or rupture may result. become wet.
If the battery pack will not be used for a long period of
Do Not Charge the Battery Using Methods Other Than time (a month or more), charge or discharge (use) the
Those Specified battery pack until the remaining battery level becomes
If the battery is not charged using one of the specified 30% to 40% and store it in a cool, dry place.
methods, electrolyte leakage, generation of heat, ignition This computer prevents overcharging of the battery by
or rupture may result. recharging only when the remaining power is less than

Getting Started
approx. 95% (when Economy Mode (ECO) is enabled:
Do Not Throw the Battery Pack into a Fire or Expose It 75%) of capacity.
to Excessive Heat The battery pack is not charged when the computer is
Generation of heat, ignition or rupture may result. first purchased. Be sure to charge it before using it for
the first time. When the AC adaptor is connected to
Avoid Extreme Heat (Near the Fire, in Direct Sunlight, the computer, charging begins automatically.
for Example) Should the battery leak and the fluid get into your
Electrolyte leakage, generation of heat, ignition or rupture eyes, do not rub your eyes. Immediately flush your
may result. eyes with clear water and see a doctor for medical

Useful Information
treatment as soon as possible.
Do Not Insert Sharp Objects into the Battery Pack, NOTE
Expose It to Bumps or Shocks, Disassemble, or Mod- The battery pack may become warm during
ify It recharging or normal use. This is completely nor-
Electrolyte leakage, generation of heat, ignition or rupture mal.
may result. Recharging will not commence if internal tempera-
ture of the battery pack is outside of the allowable
Do Not Short the Positive (+) and Negative (-) Con- temperature range (0 °C to 55 °C {32 °F to 131
tacts
Generation of heat, ignition or rupture may result. Do not °F}). ( Reference Manual “Battery Power”)
place the battery pack together with articles such as neck- Once the allowable range requirement is satisfied,

Troubleshooting
laces or hairpins when carrying or storing. charging begins automatically. Note that the
recharging time varies based on the usage condi-
Do Not Use This Product with a Battery Pack Other tions. (Recharging takes longer than usual when
Than the One Specified the temperature is 10 °C {50 °F} or below.)
Use only the specified battery pack with your product. If the temperature is low, the operating time is
Use of battery packs other than those manufactured and shortened. Only use the computer within the
supplied by Panasonic may present a safety hazard allowable temperature range.
(generation of heat, ignition or rupture). The battery pack is a consumable item. If the
amount of time the computer can be run by using a
particular battery pack becomes dramatically
shorter and repeated recharging does not restore
its performance, the battery pack should be
Appendix
A lithium ion battery that is recyclable
replaced with a new one.
powers the product you have pur-
When transporting a spare battery inside a pack-
chased.
age, briefcase, etc., it is recommended that it be
Please call 1-800-8-BATTERY for
placed in a plastic bag so that its contacts are pro-
information on how to recycle this
tected.
battery.
Always power off the computer when it is not in
use. Leaving the computer on when the AC adap-
L’appareil que vous vous êtes
tor is not connected will exhaust the remaining bat-
procuré est alimenté par une batterie
tery capacity.
au lithium-ion.
Pour des renseignements sur le recy-
clage de la batterie, veuillez com-
poser le 1-800-8-BATTERY.
 CONTENTS
1. Specifications 1-1
2. Names and Functions of Parts 2-1
3. Block Diagram 3-1
4. Diagnosis Procedure 4-1
5. Power-On Self Test (Boot Check) 5-1
6. List of Error Codes <Only when the port replicator is connected> 6-1
7. Self Diagnosis Test 7-1
8. Wiring Connection Diagram 8-1
9. Disassembly/Reassembly 9-1
10. Exploded View 10-1
11. Replacement Parts List 11-1
1. Specifications
This page provides the specifications for the basic model CF-30FTSAZAM/CF-30F3SAZAM.
The model number is different according to the unit configuration.

To check the model number:

Check the bottom of the computer or the box the computer came in at the time of purchase.
To check CPU speed, memory size and the hard disk drive (HDD) size:
Run the Setup Utility ( Reference Manual “Setup Utility”) and select [Information] menu.
[CPU Speed]: CPU speed, [System Memory]: Memory size, [Hard Disk]: Hard disk drive size

Main Specifications
Model No. CF-30FTSAZAM CF-30F3SAZAM
CPU Intel® Core™ 2 Duo Processor L7500 (1.6 GHz, 4 MB*1 L2 cache, 800 MHz FSB)
Chipset Intel® GM965
Memory*2*4 1 GB (4 GB Max.)
Video Memory*1*3 UMA (384 MB Max.)
*4
Hard Disk Drive 80 GB
Display Method 13.3 XGA type (TFT) with Touchscreen 13.3 XGA type (TFT)
Internal LCD*5 65,536/16,777,216 colors (800 × 600 dots/1024 × 768 dots)
External Display*6 65,536/16,777,216 colors (800 × 600 dots/1024 × 768 dots/1280 × 768 dots/1280 × 1024 dots/
1440 × 900 dots)
Wireless LAN*7 Next page
*8
Bluetooth™ Next page
LAN IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX, IEEE 802.3ab 1000BASE-T
Modem Data: 56 kbps (V.92) FAX: 14.4 kbps
Sound WAVE and MIDI playback, Intel® High Definition Audio subsystem support, Monaural speaker
Security Chip TPM (TCG V1.2 compliant)*9
Card Slot PC Card Type I or Type II x 1 (3.3 V: 400 mA, 5 V: 400 mA)
ExpressCard ExpressCard/34*10 or ExpressCard/54 x 1
*11
SD Memory Card x 1, Data transfer rate = 8 MB per second*12
Smart Card*13 ISO7816 x 1
RAM Module Slot 200-pin, 1.8 V, SO-DIMM, DDR2 SDRAM, PC2-4200 Compliant
Interface USB port (4-pin, USB 2.0) x 3, Serial port (Dsub 9-pin male), Modem port (RJ-11), LAN port
(RJ-45), External display port (Mini Dsub 15-pin female), Expansion Bus Connector (Dedicated
80-pin female), External Antenna Connector (Dedicated 50 Ω coaxial connector), IEEE 1394a
Interface Connector (4-pin x 1), Microphone Jack (Miniature jack, 3.5 DIA, Stereo), Headphone
Jack (Miniature jack, 3.5 DIA, Impedance 32 Ω, Output Power 4 mW × 2)
Keyboard / Pointing Device 87 keys / Touch Pad / Touchscreen (Anti- 87 keys / Touch Pad
Reflection, Stylus (included) touch capable)
Power Supply AC adaptor or Battery pack
AC Adaptor*14 Input: 100 V to 240 V AC, 50 Hz/60 Hz, Output: 15.6 V DC, 5.0 A
Battery Pack Li-ion 10.65 V, 8.55 Ah
*15
Operating Time Main Battery: Approx. 7 hours*16
Main Battery + Second Battery: Approx. 10.5 hours*16
Charging Power on Main Battery: Approx. 8.5 hours
Time*15 Main Battery + Second Battery: Approx. 12.5 hours
Power off Main Battery: Approx. 5 hours
Main Battery + Second Battery: Approx. 8 hours
Clock Battery Coin type lithium battery 3.0 V
Power Consumption*17 Approx. 50 W*18 / Approx. 70 W (Maximum when recharging in the ON state)
Physical Dimensions (W × H × D) 302 mm × 67.5 - 69.5 mm × 292 mm {11.9" × 2.7 - 2.8" × 11.5"}
Weight Approx. 3.8 kg {Approx. 8.4 lb.}, excluding the dummy pack and dummy cards (approx. 50 g
{approx. 1.8 oz.})
Operation Environment Temperature: 5 °C to 35 °C {41 °F to 95 °F}
Humidity: 30% to 80% RH (No condensation)
Storage Environment Temperature: -20 °C to 60 °C {-4 °F to 140 °F}
Humidity: 30% to 90% RH (No condensation)

1-1
 Main Specifications
Operating System Microsoft® Windows® XP Professional Service Pack 2 with Advanced Security Technologies
(NTFS File System)
Utility Programs DMI Viewer, Microsoft® Windows® Media Player 10, Adobe Reader, PC Information Viewer,
SD Utility, Icon Enlarger, Loupe Utility, Intel® Matrix Storage Manager, Intel® PROSet/Wireless
Software*7, Bluetooth™ Stack for Windows® by TOSHIBA*8 , Wireless Switch Utility, Hotkey Set-
tings, Battery Recalibration Utility, Panasonic Hand Writing, Infineon TPM Professional Pack-
age*19, Recover Pro™ 6*19 or Recover Pro™ VX*19, Power Saving Utility, Wireless Connection
Disable Utility
Setup Utility, Hard Disk Data Erase Utility*20, PC-Diagnostic Utility

Wireless LAN <Only for model with wireless LAN>

Intel Wireless WiFi Link 4965AG (802.11 a + b + g)*21
Data Transfer Rates*22 IEEE802.11a: 54/48/36/24/18/12/9/6 Mbps (automatically switched)
IEEE802.11b: 11/5.5/2/1 Mbps (automatically switched)
IEEE802.11g: 54/48/36/24/18/12/9/6 Mbps (automatically switched)
Standards Supported IEEE802.11a/IEEE802.11b/IEEE802.11g
Transmission method OFDM system, DSSS system
Wireless Channels Used IEEE802.11a: Channels 36/40/44/48/52/56/60/64/149/153/157/161/165
IEEE802.11b/IEEE802.11g: Channels 1 to 11
RF Frequency Band IEEE802.11a: 5.18-5.32 GHz, 5.745-5.825 GHz
IEEE802.11b/IEEE802.11g: 2.412-2.462 GHz

BluetoothTM <Only for model with Bluetooth>

Bluetooth Version 2.0 + EDR
Transmission method FHSS system
Wireless Channels Used Channels 1 to 79
RF Frequency Band 2.402-2.48 GHz

*1
1MB = 1,048,576 bytes
*2
You can physically expand the memory upto 4 GB, but the total amount of usable memory available will be less depending on
the actual system configuration.
*3
A segment of the main memory is allotted automatically depending on the computer’s operating status. The size of the Video
Memory cannot be set by the user.
*4
1GB = 1,000,000,000 bytes. Your operating system or some application software will report as fewer GB.
*5
A 16,777,216 color display is achieved by using the dithering function.
*6
Maximum resolution depends on the specifications of the external display.
*7
Only for model with wireless LAN
*8
Only for model with Bluetooth
*9
For information on TPM, click [start] - [Run] and input “c:\util\drivers\tpm\README.pdf”, and refer to the Installation Manual of
“Trusted Platform Module (TPM)”.
*10
When using ExpressCard/34, the card slot cover cannot be closed.
*11
SD Memory Cards that support high-speed transfer rates can be used. Windows Ready Boost function is also supported. Op-
eration has been tested and confirmed using Panasonic SD Memory Cards and SDHC Memory Cards with a capacity of up to
8 GB. Operation on other SD equipment is not guaranteed.
This computer is not compatible with MultiMediaCards. Do not insert this kind of cards.
*12
Theoretical value and not the actual speed. The transfer rate does not become higher even if you use a card that supports the
higher transfer rate.
*13
Only for model with Smart Card slot
*14
<Only for North America>
The AC adaptor is compatible with power sources up to 240 V AC adaptor. The computer is supplied with a 125 V AC compat-
ible AC cord. 20-M-2-1
*15
Varies depending on the usage conditions.
*16
Measured using MobileMark™ 2005 (LCD brightness: 60 cd/m2)
*17
Approx. 0.9 W when the battery pack is fully charged (or not being changed) and the computer is OFF.
*18
Rated power consumption 23-E-1
*19
You need to install to use the feature.
*20
The Product Recovery DVD-ROM is required.
*21
It does not correspond to IEEE802.11.n.
*22
These are speeds specified in IEEE802.11a+b+g standards. Actual speeds may differ.

1-2
2. Names and Functions of Parts
F

G
H
I
J
K
K
A
L
EX
PC K
D M
N
E
O

A: Bluetooth Antenna : Battery status

<Only for model with Bluetooth> Reference Manual “Battery Power”
Reference Manual “Bluetooth” : Power status
B: ExpressCard Slot (Off: Power off/Hibernation, Green: Power on,
Blinking green: Standby)
Reference Manual “PC Card / ExpressCard”
: Wireless ready*1
C: PC Card Slot
This indicator lights when Wireless LAN, Blue-
Reference Manual “PC Card / ExpressCard” tooth, and/or Wireless WAN are connected and
D: Multimedia Pocket ready. It does not necessarily indicate the On/Off
Reference Manual “Multimedia Pocket” condition of the wireless connection.
E: Battery Pack Reference Manual “Wireless LAN” “Blue-
F: Wireless LAN Antenna tooth” “Disabling / Enabling Wireless Commu-
<Only for model with wireless LAN> nication”
Reference Manual “Wireless LAN” : Wireless WAN status
G: LCD <Only for model with wireless WAN>
<Only for model with touchscreen> Refer to the instruction manual of the wireless
device
Reference Manual “Touchscreen”
L: Power Switch
H: Function Key
M: Wireless Switch*1
Reference Manual “Key Combinations” Reference Manual “Disabling / Enabling Wire-
I: Keyboard less Communication”
J: Touch Pad
N: Carrying Handle
K: LED Indicator
O: Stylus Holder
: Caps lock
: Numeric key (NumLk) *1
<Only for model without both wireless LAN and Bluetooth>
: Scroll lock (ScrLk) Both Wireless Switch and Wireless ready indicator are
: Multimedia pocket device status or the second equipped with models without Wireless device as well.
battery status Wireless ready indicator lights up when Wireless Switch
Reference Manual “Multimedia Pocket” is turned on, or [Wireless Switch] is set to [Disable] ([En-
“Battery Power” able] in the default setting) on Setup Utility [Advanced]
: Hard disk drive status menu, but Wireless function does not work. (Do not
: Power status of the multimedia pocket change [Wireless Switch] setting.)

A lithium ion battery that is recyclable powers the product you have purchased.
Please call 1-800-8-BATTERY for information on how to recycle this battery.

L’appareil que vous vous êtes procuré est alimenté par une batterie au lithium-ion.
Pour des renseignements sur le recyclage de la batterie, veuillez composer le
1-800-8-BATTERY.

2-1
Right side

A B C DE F G H I
1394

Rear side Bottom

Q

J H K L M N O P
R

A: Hard Disk Drive M: External Display Port

Reference Manual “Hard Disk Drive” Reference Manual “External Display”
B: SD Memory Card Slot N: Headphone Jack
Reference Manual “SD Memory Card” You can connect headphones or amplified speakers.
C: SD Memory Card Indicator When they are connected, audio from the internal
(Blinking: During access) speakers is not heard.
O: Microphone Jack
Reference Manual “SD Memory Card” A condenser microphone can be used. If other types
D: IEEE 1394 Interface Connector of microphones are used, audio input may not be pos-
Reference Manual “IEEE 1394 Devices” sible, or malfunctions may occur as a result.
When recording in stereo using a stereo micro-
E: Smart Card Slot phone:
<Only for model with Smart Card slot> Click [start] - [All Programs] - [SoundMAX] - [Con-
Reference Manual “Smart Card” trol Panel] and select [Microphone], and then add
F: Modem Port a check mark for [No Filtering] in [Microphone En-
Reference Manual “Modem” hancements].
• When using a monaural microphone with a 2-termi-
G: LAN Port
nal plug:
Reference Manual “LAN” Click [start] - [All Programs] - [SoundMAX] - [Con-
H: USB Port trol Panel] and select [Microphone], and then add
Reference Manual “USB Devices” a check mark for [Voice Recording] in [Microphone
I: DC-IN Jack Enhancements].
J: Security Lock Otherwise, only audio on the left track will be record-
A Kensington cable can be connected. ed.
For further information, read the manual that comes P: Serial Port
with the cable. Q: RAM Module Slot
K: Ext Antenna Connector Reference Manual “RAM Module”
L: Expansion Bus Connector R: Speaker
Reference Manual “Port Replicator” Reference Manual “Key Combinations”

2-2
 Merom DC
Intel Core
CoreTM2
4MB L2 Cache
Duo processor
pro essor
1.6GHz, FSB 800MHz

Fr
onts
ideBu
s 800MHz 1.05V

5.3Gbytes/sec

AMP Speaker
LCD SO-DIMM Memor
Internal DRAM 64bit BUS 1.8V 533MHz
13.3”
13.3 XGA DDR2 SDRA RJ11
Graphics Interface 4.2Gbytes/sec
1000nit 2GB
3 Block Diagram

Sound Headphone
GM965 Data Modem HDA
CRT DMI SO-DIMM Memory
INTEL 64bit BUS 1.8V 533MHz MDC1.5 AD1884 Ext. MIC
Interface DDR2 SDRAM
4.2Gbytes/sec
2GB

AC Link
BIOS 3.3V
SPI 133Mbytes/sec 32b
itPCI
Bus33MHz
8M

1Gbytes/sec x2
Wireless LAN
4965ABG antenna PCMCIA SD Card
SATA
802.11 A/B/G R5C847
SATA HDD (1.5Gb/s) HDD HDD PCI IEEE1394
80GB 2.5” Interface Interface Bridge
PATA

3-1
MP Buffer PATA I
CH8-
M Et
her
netGb
E
IDE AC-link
1.5V Marvell Yucon Ultra RJ45 TYPE II
Interface Interface
INTEL 88E8055-B0-NNC1
USB2.0
USB 2.0 LPC PCI Express C000
3p
ort
Interface Bridge Bridge

ExpressCARD
USB2.0 HUB
1.1/2.0
r
(PotRe
p.) 3.3V
Touch 17Mbytes/sec
Screen
LPCBu
s

TPM 1.2 EC/KBC Flat Pad

Blue-tooth Wireless cinfig CN Super I/O
infineon (M306KA)
Internal USB1.1 Internal USB1.1 SIO10N268 Thermister (Novato)
SMSC

Finger Print GPS PS/2 Int. KB

Buffer Li-Ion
USB1 1 (KB& Mouse)
LED Battery
KBD BKLT Pack Battery Charger
Parallel Smart Card Mouse
Serial Serial (PortRep.) 2nd-Li-Ion
HDD
(PortRep) Battery
Heater
Pack
4 Diagnosis Procedure
4.1. Basic Procedures

4-1
4.2. Troubleshooting
Please take note of the following two points with regard to troubleshooting:
1. Know-how of diagnosis upon occurrence of heavy troubles, e.g. Set cannot be turned ON , Set fails to start , No display on
screen , etc.
2. Explanation of each trouble, mainly symptom of trouble in operation.

Flow Chart Pay attention to the following points when in pursuit of the cause of a troubleshooting.
1. Peripheral apparatus connected with the set should all be removed before operation check.
START
START 2. Make sure that cables, boards, etc. are not coming off, and recheck the contact condition.

Set cannot be supplied with current. AC NG

Adaptor/Battery Replace AC Adaptor/Battery
Power lamp fails to light up. Output voltage
OK
NO Check contact condition of power input terminal. Replace if
Power lamp
check defective.
YES Check Power SW. Replace if defective.

Dark display on screen. NG Replace inverter board.

Inverter board
Screen fails to display. Check inverter cable continuity. Replace if defective
OK

LCD back NO Replace LCD back light.

light lighting

YES
LCD unit
NG
Replace LCD unit.
check
OK

BIOS operation NO Replace main board (Check fuse at power source).

Failure in starting
check
YES

Result of NG Refer to POST Replace main board.

POST error code table.
OK

Set-up utility NG Replace main board. Heavy trouble e.g.,

starting Set cannot be turned
ON , Set fails to start ,
OK No display on
Return set-up utility setpoint to the state of delivery from factory . screen , etc.

Check HDD cable connection and continuity.

NO
HDD access Replace if defective.
Replace HDD & Reinstall.
YES Replace main board.

Main board
NG
Not displayed properly on screen. Replace main board
check
OK
Some or all keys cannot be input. Make sure of contact of K/B connector in use. Each kind of
Replace keyboard or main board. trouble in
operation.
Trouble NO Check if there are any flaws on CD media. Since
CD CALL not practicable. symptoms on some flaws may appear on specific media, CD media
of CD
can be defective.
YES
Replace main board.

Starts but operates unstably. Reinstall HDD.

Replace main board.

START
END

4-2
5 Power-On Self Test (Boot Check)
Outline of POST

The set has a boot check function called POST (Power-On Self Test) in it.
The condition of the main body is diagnosed by checking beep sound or error code.
Start .............Test begins automatically when power switch is set to ON.
Normal finish .....After memory checking, a beep sound is issued once and the set is placed into automatic stop.
Note: If no error occurs, nothing is displayed. (No display of OK, etc.)

Error Diagnosis by Checking Beep Signal Sound

The beep sound is as follows:

(1 (long sound) -2-3-4)

(Length of bar shows length of sound.)

= long sound (about 0.4 sec.), = short sound (about 0.2 sec.), Length between sounds is about 0.1 sec.

Table of errors classified by beep sounds

Diagnosis Beep signal sound Error message

Main board 1(long sound)-2 BIOS ROM error
1-2-2-3 BIOS ROM error
1-3-1-1 RAM error
1-3-1-3 Keyboard controller error
1-3-4-1 RAM error
1-3-4-3 RAM error
1-4-1-1 RAM error
2-1-2-3 BIOS ROM error
2-2-3-1 Occurrence of unexpected offering
(Note) A beep sound is also issued in case of other I/O trouble.

5-1
6 List of Error Codes <Only when the port replicator is connected>

The following is a list of the messages that BIOS can display. Most of them occur during
POST. Some of them display information about a hardware device, e.g., the amount of memory
installed. Others may indicate a problem with a device, such as the way it has been configured.
Following the list are explanations of the messages and remedies for reported problems.
If your system displays one of except the messages marked below with an asterisk (*), write
down the message and contact Panasonic Technical Support. If your system fails after you
make changes in the Setup menus, reset the computer, enter Setup and install Setup defaults
or correct the error.

0200 Failure Fixed Disk

Fixed disk in not working or not configured properly. Check to see if fixed disk is attached
properly. Run Setup. Find out if the fixed-disk type is correctly identified.
0210 Stuck key
Stuck key on keyboard.
0211 Keyboard error
Keyboard not working.
0212 Keyboard Controller Failed
Keyboard controller failed test. May require replacing keyboard controller.
0213 Keyboard locked - Unlock key switch
Unlock the system to proceed.
0230 System RAM Failed at offset : nnnn
System RAM failed at offset nnnn of in the 64k block at which the error was detected.
0231 Shadow RAM Failed at offset : nnnn
Shadow RAM failed at offset nnnn of the 64k block at which the error was detected.
0232 Extended RAM Failed at offset : nnnn
Extended memory not working or not configured properly at offset nnnn.
0250 System battery is dead - Replace and run SETUP
The CMOS clock battery indicator shows the battery is dead. Replace the battery and run Setup
to reconfigure the system.
*0251 System CMOS checksum bad - Default configuration used
System CMOS has been corrupted or modified incorrectly, perhaps by an application program
that changes data stored in CMOS. The BIOS installed Default SETUP Values. If you do not
want these values, enter Setup and enter your own values. If the error persists, check the system
battery or contact Panasonic Technical Support.
0260 System timer error
The timer test failed. Requires repair of system board.
0270 Real time clock error
Real-time clock fails BIOS test. May require board repair.
*0280 Previous boot incomplete - Default configuration used
Previous POST did not complete successfully. POST loads default values and offers to run
Setup. If the failure was caused by incorrect values and they are not corrected, the next boot
will likely fail. On systems with control of wait states, improper Setup settings can also termi-
nate POST and cause this error on the next boot. Run Setup and verify that the wait-state
configuration is correct. This error is cleared the next time the system is booted.
0281 Memory Size found by POST differed from EISA CMOS
Memory size found by POST differed from EISA CMOS.

6-1
02D0 System cache error - Cache disabled
Contact Panasonic Technical Support.
02F0: CPU ID:
CPU socket number for Multi-Processor error.
02F4: EISA CMOS not writable
ServerBIOS2 test error: Cannot write to EISA CMOS.
02F5: DMA Test Failed
ServerBIOS2 test error: Cannot write to extended DMA (Direct Memory Access) registers.
02F6: Software NMI Failed
ServerBIOS2 test error: Cannot generate software NMI (Non-Maskable Interrupt).
02F7: Fail - Safe Timer NMI Failed
ServerBIOS2 test error: Fail-Safe Timer takes too long.
device address Conflict
Address conflict for specified device.
Allocation Error for: device
Run ISA or EISA Configuration Utility to resolve resource conflict for the specified device.
Failing Bits : nnnn
The hex number nnnn is a map of the bits at the RAM address which failed the memory test.
Each 1 (one) in the map indicates a failed bit. See error 230,231 or 232 for offset address of the
failure in System, Extended or Shadow memory.
Invalid System Configuration Data
Problem with NVRAM (CMOS) data.
I/O device IRQ conflict
I/O device IRQ conflict error.
Operating System not found
Operating system cannot be located on either drive A: or drive C:. Enter Setup and see if fixed
disk and drive A: are properly identified.
Parity Check 1 nnnn

Troubleshooting
Parity error found in the system bus. BIOS attempts to locate the address and display it on the
screen. If it cannot locate the address, it displays ????. Parity is a method for checking errors
in binary data. A parity error indicates that some data has been corrupted.
Parity Check 2 nnnn
Parity error found in the I/O bus. BIOS attempts to locate the address and display it on the
screen. If it cannot locate the address, it displays ????.
Press <F1> to resume, <F2> to Setup
Displayed after any recoverable error message. Press <F1> to start the boot process or <F2> to
enter a Setup and change the settings. Write down and follow the information shown on the
screen.

6-2
7 Self Diagnosis Test
As for the self-diagnosis test(PC-Diagnostic utility) to use this model, a standard test and the
enhancing test by the module of the main body building in are possible.
●Notes To skip BIOS password
Use <Ctrl>+<F10> key to skip BIOS password or authentication of fingerprint.
This key is only for entering DIAG mode. Not available to boot the computer.
If customer set "HDD Lock", the DIAG program cannot perform HDD test.
*This key is for service purpose only. Do not disclose this information to unrelated others.

1. Beginning of self-diagnosis test

1-1. Setting of content of setup

1. The power supply of the computer is turned on.

2. " F2 " is pushed on the screen of "Panasonic" while " press <F2 to enter Setup> " is displayed.
3. The setup utility starts and then takes notes of the content of the BIOS setup of present set.
4. " F9 " is pushed, " Yes" is selected on the screen of " Is the default value loaded? ", and " Enter"
is pushed.
5. " F10 " is pushed.
6. " Yes" is selected on the screen of the setup confirmation, and " Enter" is pushed.
7. The computer starts automatically.
Attention
・If the device which can be set is set to "Invalidity" by "Advanced" or "Security" menu, becomes an
error by "PC-Diagnostic utility".
(It is judged that the device which can be set to "Invalidity" by "Main" menu such as "Flat pad" is
normal if the controller operates normally though sets to "Invalidity" by the setup. )
・In the model with built-in DVD of the USB connection, even if DVD is normal, becomes an error if
legacy USB is set to "Invalidity"

1-2. When you execute an automatic test

1. "Ctrl" + "F7" is pushed while the "Panasonic" start screen is displayed after the computer is started.
2. The test of all devices begins automatically by "PC-Diagnostic utility" 's starting.
Attention
・It is a test which the customer who bought PC can execute. (As for HDD, the enhancing test is also
possible.)
・A flat pad does not work for a while after starting "PC-Diagnostic utility".
・The movement of a flat pad might become abnormal If after RAM begins from the CPU/System
test, a flat pad will be operated in about 30 seconds. In that case,restarts pushing"Alt" + "Ctrl" +
"Del" key. Or, please start "PC-Diagnostic utility" again after doing the power supply switch in the
slide, and turning off the power supply.

1-3. When you execute the enhancing test

1. Please let me discontinue diagnosing clicking to end an automatic test.

2. Please click on the character of "D" "PC-Diagnostic utility" on the screen while pushing both of right
"Shift" and left "Shift" keys.

3. All devices which can select the enhancing test make the setting of the enhancing test possible.
4. The district device is made"FULL" display (enhancing test).
5. The test begins clicking .

*Please refer to item 4 for the error result of each test and the division of the breakdown part.

7-1
2. Operation of PC-Diagnostic Utility
-Only the device which can be inspected on the entire screen is displayed.
-The item does not appear when the device of wireless LAN etc. is not physically connected.
-The movement of the item must use an arrow key or a flat pad.

-As for the device under the diagnosis, blue and yellow are alternately displayed at the left of the icon.
- The diagnosis result of the device greens at the left of the icon when it is normal, and becomes red when
abnormal.

-When the test of all devices ends, the test result is displayed under the right of the screen.

-Please click while diagnosing when being stop on the way by the time the test of all devices ends.
-Please click when you restart "PC-Diagnostic utility".
*Each device is tested from the beginning, and it is not possible to restart on the way.
-When the test of all devices ends, the test result is displayed under the right of the screen.

7-2
2-1. Selection of tested device

-To test only a specific device, "Test" and "Do not test" of each device can be selected.
-The device which can select the enhancing test changes in order of "The standard is tested" and "Do not
test" whenever the device icon is clicked.

Start the standard test Do not test

Please begin testing clicking if the selection of the tested device ends.

2-2. "PC-Diagnostic utility" End method

When of "Close" on the right of the screen is clicked, the computer reactivates automatically. Or, the
power supply switch is done in the slide and the power supply is turned off.

2-3. The content of the setup is returned to the setting of the user
1. Turned on the computer.
2. "F2" is pushed on the screen while "Press<F2>to enter Setup" is displayed of "Panasonic".
3. Push "F10", and on the screen of "Is the change in the setting preserved and do end?"and then "Yes"
is selected, and "Enter" is pushed.
4. The computer reactivates automatically.
5. The end option is chosen by the start menu, and the power supply of the computer is turned off.

Standard at test time

All devices other than RAM and HDD ---------- about 1 minute
RAM standard test ----------------------------------- 1 - 2 minutes
HDD standard test ----------------------------------- 2 - 3 minutes
HDD enhancing test (60GB) ---------------------- about 40 minutes

Ex.The standard when the standard <all device> is tested becomes 1+2+3=6 minutes.

■ There is greatly a difference from RAM test when the memory is increased according to the performance
of the memory occasionally.
■ Moreover, when the main body of PC under the test is a high temperature, it occasionally takes time.
■ There is greatly a difference from HDD according to the performance of the drive occasionally.

7-3
3. Test Item and Division of trouble

Test item Stanard Enhan- Content of standard test Content of enhancing test Place with possibili-
cing ty of breakdown

CPU is shifted to protected mode, and

"Violation of the paging", "Operation of CPU /
CPU / the violation of a privileged instruction",
SYSTEM Main board
and DMA, INT, TIMER, and the
RTC operation are confirmed.

All memory space is tested in a special Memory /

RAM memory access pattern based on
Mainboard
"R.S.T . technology".

The record area frequently accessed HDD /

with Microsoft Windows XP to test in Mainboard /
HDD about two minutes regardless of All record area is tested.
Cable /
points of HDD is emphatically tested. Connector

It is confirmed not to find abnormality MODEM/

MODEM in the AC97 modem controller. Mainboard

Wireless LAN
Wireless It is confirmed not to find abnormality board /
LAN in the Wireless LAN modem controller. Connector /
Mainboard
Sound *5

It is confirmed not to find ab-

normalityin the wiring between
It is confirmed not to find abnormality the USB controller and the Mainboard /
*1
USB in the USB controller. connector by confirming Connector
the connection of the USB
equipment connected with the
USB connector.

It is confirmed not to find ab-

normalityin the wiring between
*2 It is confirmed not to find abnormality Mainboard /
LAN the controller and the
in the LAN controller.
connector by connecting to
Connector
HUB with LAN cable.

It is confirmed not to find abnormality

PC Card Mainboard
in the CardBus controller.

It is confirmed not to find abnormality Mainboard

SD
in the SD controller.

It is confirmed not to find abnormality The key is actually input, and Mainboard /
*3
Keyboard in keyboard controller's keyboard inte- the operation is displayed on
Keyboard
rface. the screen.

Whether keyboard controller's mouse The operation is actually dis- Mainboard /

*4
Touch Pad interface operates normally is confir- played on the screen by ope- Touch Pad
med. rating the touch pad.
Mainboard /
*6 The drive is normally reset, and it is It is confirmed to be able to DVD Drive /
DVD-ROM
accessible is confirmed. read media normally. DVD Cable /
DVD Connector

7-4
 The place with possibility of
Test Item Standard Enhanced Content of Standard Test Content of Extend Test
breakdown
It is confirmed not to find
Perform Touch Screen
abnormality in the USB
functionality practically. Main board/
Touch Screen connection of Touch Screen.
Operator has to judge Touch Screen
This test cannot find
PASS/FAIL with test result.
abnormality of Touch Screen.
It is confirmed not to find
abnormality in the connection
Bluetooth Bluetooth cable
of Main board and Bluetooth
module.
It is confirmed not to find
abnormality in the connection
Wireless WAN WWAN cable
of Main board and Wireless
WAN module.
It is confirmed not to find
abnormality in the legacy FD FD Drive/
drive. Main board (Super I/O)/
Floppy
This test cannot find FDD cable
abnormality of mechanical FDD connector
breakdown. (e.g.. Head, Motor)
It is confirmed not to find
abnormality in access to Main board
VRAM with VESA. (Chipset, Graphic
Video
The PC which uses main Controller)/
memory as VRAM may fail with Memory
main memory failure.
It is confirmed not to find
GPS abnormality in the connection GPS cable
of Main board and GPS
It is confirmed not to find
Main board
IEEE1394 abnormality in the IEEE1394
(IEEE#394 Controller)
controller.
It is confirmed not to find
abnormality in the wiring Main board (Chipset)/
Express Card
between Chipset and Express Express Card Connector
Card.
It is confirmed not to find
Main board
Smart Card abnormality in the Smart Card
(Smart Card Controller)
controller.
It is confirmed not to find
It is confirmed not to find
abnormality in the wiring
abnormality of Super I/O
between Super I/O and Serial
UART function. Main board (Super I/O)/
Serial Port *7 Connector.
This test cannot find lack of Serial Connector
This test cannot find failure of
wiring between Super I/O and
cable characteristic and device
Serial Connector.
problems.
It is confirmed not to find
It is confirmed not to find
abnormality in the wiring
abnormality of Super I/O
between Super I/O and
parallel function. Main board (Super I/O)/
Parallel Port *8 Parallel Connector.
This test cannot find lack of Parallel Connector
This test cannot find failure of
wiring between Super I/O and
cable characteristic and device
Parallel Connector.
problems.
*1 Please connect the USB device with the port (USB connector) which wants to test before the tests.
*2 Please connect LAN port with LAN HUB with LAN cable before the tests.
*3 The operator actually inputs the key, and the operator judges PASS/FAIL of the test.
*4 The operator actually operates the mouse, and the operator judges PASS/FAIL of the test.
*5 It is not abnormal though the sound is emitted from the speaker while testing.
When the test result is PASS, trouble is thought by not hearing of the sound under the test from
the speaker and the headphone by the wiring of the audio output system.
*6 Please set DVD/CD media in the drive before the tests.
*7 Please set a Special Loop Back Connector Tool at serial connector for Enhanced Test.
(This Connector Tool is same as the one used before.)
*8 Please set a Special Loop Back Connector Tool at parallel connector for Enhanced Test.
(This Connector Tools is same as the one used before.)

7-5
Wiring Connection Diagram

EXTERNAL
USB USB EXPANSION DISPLAY HEAD MICRO SERIAL
PORT PORT BUS PORT PHONE PHONE PORT

CN100 CN705 CN703

CN102 CN101 CN702
CN701 CN700 JK701 JK700
I/O PCB
USB PCB
USB CN103
BACK LIGHT
PORT
ANTENNA
TOUCH SCREEN PCB
INVERTER PCB

LCD
CN201

CN1
TS PCB
CN2
CN200 CN1

EXT ANT.
PCB

DC-IN JK1
CN37
CN2 W-LAN
CN27 MODULE
CN3
CN1
LAN PORT CN21 CN17
CN11
CN20
CN22 MAIN PCB
MP PCB EXPRESS
CARD
DIMM MEMORY CARD CN12
CN400

CN402 CN13
CN401 CN15 CN19 RTC SPEAKER
BATTERY
CN6
CN10
CN5 CN26
COMBO CN28
DRIVE CN25
CN14 PCMCIA
CN4 CN29
CN24 CN18 CARD
CN8 CN7 CN9

IEEE1394
INTERFACE CN31 CN30
CONNECTOR
BT PCB
PW LED SW LED KEYBOARD
PAD PCB
PCB PCB
CN802 J1 J2
CN301 CN801
HDD FPC CN800 MDC JK1
CN300
BATTERY MODEM

CN1
LED PCB
SD MAIN MODEM GPS PCB
HDD TOUCH CN901
CARD BATTERY PAD PORT

6-1
7 Disassembly/Reassembly
Note:
Power off the computer. Do not shut down to the Suspend or hibernation mode.
Do not add peripherals while the computer is in the Suspend or hibernation mode; abnormal operation may result.

7.1. Disassembly Instructions 7.1.2. Removing the Battery Pack and HDD
Pack
7.1.1. Preparation
Before disassembling, be sure to make the following prepara-
tions.
• Shut down Windows and turn off the power.
• Disconnect the AC adaptor.
• Remove the optional DIMM memory card and PCMCIA card if
they are connected.
• Remove other devices if they are connected.

Attention:
• Please execute writing BIOS ID when you exchange the Main Battery
Board. Cover
• Parts (Sheet and rubber) etc. related various the Conductive
Cloth and Heat Spreader cannot be recycled. Use new parts.

HDD Cover

Battery Pack

HDD Pack

1. Open the Battery Cover.

2. Remove the Battery Pack.
3. Open the HDD Cover.
4. Remove the HDD Pack.

7-1
7.1.3. Removing the HDD 7.1.4. Removing the KB Cover, Hinge
Cover L, Hinge Cover R and Key-
HDD U Case Ass'y
board
<K1-17> <K1-17>
HDD FPC <N6> <N6>
Bluetooth PCB
<N6>
HDD <N6> <N6>
SATA Guard <N2>
<K1-16> Hinge Cover L
<N6>
<N6>
<N6>
Sheet KB Cover
Heater Ins Sheet
<N2>

HDD
Damper Hinge
Ass'y Cover R

Heater

HDD L
Case Ass'y

1. Remove the Screw. <K1-16> Keyboard

2. Remove the 4 Screws. <K1-17>
And remove the SATA Guard. 1. Remove the 4 Screws <N6>, and remove the KB Cover.
3. Release the 2 Tabs, and remove the HDD U Case Ass'y 2. Remove the 2 Screws <N2> and the 3 Screws <N6>, and
and the HDD L Case Ass'y. remove the Hinge Cover L,R.
4. Remove the HDD Dumper Ass'y. 3. Remove the Keyboard.
5. Remove the Sheet.
6. Remove the Heater and the Heater Ins Sheet. Screws <N2>: DRHM5054XA
7. Remove the HDD FPC. Screws <N6>: DRQT26+E4FKL

Screws <K1-16>: DFHE5025XA

Screws <K1-17>: DRQT2+E8FKL

7-2
7.1.5. Removing the KB Cable Cover and 7.1.6. Removing the GPS PCB and Blue-
LCD Cable Cover tooth PCB
<N29> <N12>
<N29>
<N29> <N12> <N12> GPS BT Angle
<N29>
<N29>
<N29> <N12>

KB Cable Cover
GPS PCB
<N29> <N29>
LCD Bluetooth
Cable Cover PCB
<N11>
to Connector <N29>
(CN13) to Connector <N11>
(CN14) <N29>

Connector(CN25)

to Connector
(CN25)
Keyboard
LCD
Cable Plate

1. Disconnect the Cable from the Connector. (CN25)

2. Remove the 4 Screws. <N12>
Connector
3. Remove the 2 Screws. <N11>
(CN14) 4. Remove the Bluetooth PCB, GPS BT Angle and GPS PCB.
Connector
(CN13) Screws <N11>: DFHE5025XA
Screws <N12>: DXQT2+F3FNL
1. Remove the 3 Screws <N29>.
2. Remove the LCD Cable Cover.
3. Remove the LCD Cable Plate.
4. Remove the 7 Screws <N29>.
5. Remove the KB Cable Cover.
6. Disconnect the 2 Cable from the 2 Connectors (CN13,
CN14).
7. Remove the Keyboard.

Screws <N29>: DRQT26+E3FNL

7-3
7.1.7. Removing the DIMM Cover and Bot- 7.1.8. Removing the USB PCB and Antenna
tom Cover PCB
<N1> <N1> <N1> Tape
<N1> Connector
(CN100)
DIMM Cover <N6>
USB PCB
<N1>

<N6>
<N6> Antenna PCB

Antenna Cable Connector Cover

DIMM Stopper Base (White) <N3>
<N3>
DIMM Heat Plate
Antenna Cable
(White)
DIMM Memory Card

<N17>
<N8> <N8> <N6>
<N17>
<N8> <N6>
<N6>
<N6> <N8>
<N8>
<N6>

<N6>

<N6> <N6>
<N6>
<N6>
Bottom Cover <N8>

1. Remove the Screw. <N6>

2. Disconnect the Cable from the Connector. (CN100)
3. Remove the Tape.
4. Remove the USB PCB.
5. Open the Connector Cover.
6. Remove the 2 Screws. <N3>
7. Remove the 2 white Cables and remove the Antenna PCB.

Screws <N3>: DRQT2+G6FKL

Screws <N6>: DRQT26+E4FKL

1. Remove the 5 Screws. <N1>

2. Remove the DIMM Cover.
3. Remove the 2 Screws. <N6>
4. Remove the DIMM Stopper Base.
5. Remove the DIMM Heat Plate.
6. Remove the DIMM memory card.
7. Remove the 6 Screws. <N8>
8. Remove the 11 Screws. <N6>
9. Remove the 2 Screws. <N17>
10. Remove the Bottom Cover.

Screws <N1>: DRHM0002ZA

Screws <N6>: DRQT26+E4FKL
Screws <N8>: DRSB3+8FKL
Screws <N17>: DRQT26+E6FKL

7-4
7.1.9. Removing the FPC HDD BAT 7.1.10. Removing the PAD PCB
to Connector (CN8)
to Connector (CN7) TP PCB Screw Sheet
<N16>
FPC HDD BAT
<N29> to Connector (CN9)

Tape <N29>
<N29> <N29> to Connector (CN800)
<N29> Antenna Cable Sheet
<N29>

Connector
(CN801)

Tape to Connector (CN26)

Pad PCB
HDD Cable Cover Connector(CN10)
Pad Protect
Sheet Connector(CN26)
Connector
Connector (CN802)
(CN8)

Tape

Connector
(CN7) Connector(CN9)

Connector (CN800)
1. Remove the Tape and disconnect the Cable from the Con-
Pad PCB nector. (CN801)
2. Disconnect the Cable from the Connector. (CN802)
3. Remove the TP PCB Screw Sheet.
1. Remove the 4 Screws. <N29>
4. Remove the 2 Screws. <N29>
2. Remove the HDD Cable Cover.
5. Remove the PAD PCB.
3. Remove the Antenna Cable Sheet.
4. Remove the 2 Tapes.
Screws <N29>: DRQT26+E3FNL
5. Disconnect the 2 Cables from the 2 Connectors.
(CN10,CN26) 7.1.11. Removing the Main PCB
6. Remove the Tape.
7. Disconnect the Cable from the Connector. (CN9)
8. Remove the Pad Protect Sheet. TOP Screw Sheet
9. Disconnect the Cable from the Connector. (CN800)
<N7>
10. Disconnect the 2 Cables from the 2 Connectors. (CN7,CN8)
11. Remove the Screw. <N16> Connector
(CN17)
12. Remove the FPC HDD BATT. Connector
(CN27)
Screws <N16>: DRQT26+E5FKL
Screws <N29>: DRQT26+E3FNL

1. Remove the TOP Screw Sheet.

2. Remove the Screw. <N7>
3. Disconnect the 2 Cables from the 2 Connectors.
(CN17,CN27)

7-5
 (CN400,CN401)
<N18>
11. Remove the 2 Screws. <N6>
<N16>
<N16> 12. Remove the 2 Screws. <N21>
to Connector(CN700)
<N16> 13. Remove the MP Guide.
to Connector(CN701)
<N16> <N16> <N16> 14. Remove the MP PCB.
15. Remove the Coin Battery Cushion.
16. Disconnect the Cable from the Connector. (CN19)
17. Remove the Coin Battery.
18. Remove the Tape.
19. Disconnect the 2 Cables from the 2 Connectors.
Connector(CN700) Main Chasis (CN4,CN11)
Connector
(CN31) <N17>
Connector(CN701)
Pet Tape <N17> ICH Plate
Modem
<N17> Cable Sheet <N6>
<N6>
<N11>
<N6>
Tape <N6>
<N6>
<N6>
<N11> <N11> Modem
LAN Case

<N6>
MDC Connector Modem
(J2) Cable

4. Remove the 6 Screws. <N16> <N6>

5. Remove the Screw. <N18>
6. Disconnect the 2 Cables from the 2 Connectors. <N6>
(CN700,CN701)
<N6>
7. Remove the Pet Tape and disconnect the Cable from the
<N11>
Connector. (CN31)
1394 Sheet
8. Remove the Main chasis.
20. Remove the 3 Screws <N17> and the Screw. <N11>
Tape <N21>
<N21> 21. Remove the ICH Plate.
Coin Battery Connector
Cushion Connector
MP Guide 22. Remove the 2 Modem Cable Sheets.
(CN401)
(CN400) 23. Remove the 2 Screws. <N6>
Coin Battery 24. Remove the Modem LAN Case.
MP PCB <N6>
25. Remove the 1394 Sheet.
Connector 26. Remove the 2 Screws. <N11>
<N6>
(CN4) 27. Remove the Tape.
28. Disconnect the Cable from the Connector (J2) and remove
the MDC.
29. Remove the Modem Cable.
30. Remove the 8 Screws. <N6>
31. Remove the Screw. <N11>
32. Remove the Main PCB.

Screws <N6>: DRQT26+E4FKL

Screws <N7>: DRSB26+10HKL
Connector Screws <N11>: DFHE5025XA
(CN11)
Screws <N16>: DRQT26+E5FKL
Connector
(CN19) Screws <N17>: DRQT26+E6FKL
Screws <N18>: DRSB26+8FKL
Screws <N21>: DXQT2+E12FNL

9. Remove the Tape.

10. Disconnect the 2 Cables from the 2 Connectors.

7-6
7.1.12. Removing the SD PCB, Express Card 7.1.13. Removing the I/O PCB
and PCMCIA Card
Connector I/O PCB
<N22>
<N22> (CN701)
<N22>
Connector
<N22> (CN700)
<N22> <N22> <N15>
<N22> Connector Cover
Express Card <N14>
<N30>
<N22> <N14>

<N6>
PCMCIA Card
<N6> SD PCB

Lib Cover

1. Open the Connector Cover and Lid Cover.

2. Remove the 3 Screws <N14> and the 2 Screws <N30>.
3. Remove the 4 Screws. <N15>
1. Remove the 2 Screws. <N6> 4. Remove the I/O PCB.
2. Remove the SD PCB.
3. Remove the 4 Screws. <N22> Screws <N14>: DFHE5058ZB
4. Remove the Express Card. Screws <N15>: DRHM5104ZA
5. Remove the 4 Screws. <N22> Screws <N30>: DXHM0057ZA
6. Remove the PCMCIA Card.

Screws <N6>: DRQT26+E4FKL

Screws <N22>: DXQT2+G4FNL

7-7
7.1.14. Removing the Palm Top Cover Sheet, 7.1.15. Removing the Handle and Power SW
Palm Top Cover, Touch Pad Adhe-
<K2-41>
sion Seat, Touch Pad, Touch Pad SW Handle Base L
Knob, LED PCB and SW LED PCB Handle Base R

<K2-41>
Palm Top Cover Sheet

Handle

<N29>
<N29>
<N29> <N29>

Palm Top Cover

WM SW

Touch Pad Adhesion Seat

PW LED Sheet
<K2-42>
Touch Pad

<K2-42>
PW LED Power
PCB SW
LED PCB
Touch Pad SW Knob SW LED 1. Remove the 2 Screws <K2-41>, and remove the Handle
PCB Base L and R.
2. Remove the Handle.
Touch Pad
SW Knob In 3. Remove the 2 Screws. <K2-42>
4. Remove the WM SW and Power SW.

Screws <K2-41>: DRSN4+6FKLT

Screws <K2-42>: DXQT26+D4NLT

Hole 1
Hole 2

1. Remove the Palm Top Cover sheet.

2. Remove the 5 Screws <N29>, and remove the Palm Top
Cover.
3. Remove the Touch Pad Adhesion seat.
4. Remove the Touch Pad.
5. Remove the Touch Pad SW knob and Touch Pad SW Knob
in.
6. Remove the LED PCB.
7. Remove the PW LED Sheet.
8. Remove the Screw <K2-42>, and remove the SW LCD
PCB.

Screws <N29>: DRQT26+E3FNL

Screws <K2-42>: DXQT26+D4NLT

7-8
7.1.16. Removing the Display Unit 7.1.17. Removing the LCD Rear Cabinet,
Hinge L and R
Display Unit
<N13>
left LCD Cover <N7>
Side Cover
<N7>
<N9> <N7> LCD Rear Cabinet
<N7>
<N7> <N7>
<N9>
<N9>
<N7>
<N13>
<N9> <N7>
<N7>
<N7>
Wireless Antenna
Corner Cover <N7>
<N10>

LCD Latch <N7>

<K9-1-4>
right LCD Cover
Hinge L Side Cover
Wireless Antenna
Corner Cover
<K9-1-4>
<N10>
Hinge R

1. Remove the 2 Screws <N10> and the 4 Screws <N9>.

2. Remove the Display Unit. LCD Front Cabinet

1. Remove the 4 Screws. <N7>

Screws <N9>: DRYN4+J10FKL
2. Remove the 2 Wireless Antenna Corner Covers.
Screws <N10>: DXSB4+15FNLB
3. Remove the 4 Screws <N7> and 2 Screws. <N13>
4. Remove the left and right LCD Cover Side Covers.
5. Remove the 4 Screws. <N7>
6. Remove the LCD Rear Cabinet.
7. Remove the LCD Latch.
8. Remove the 2 Screws. <K9-1-4>
9. Remove the Hinge L and R.

Screws <N2>: DRHM5054XA

Screws <N7>: DRSB26+10HKL
Screws <N13>: DRSB4+10FKL
Screws <K9-1-4>: DRYN4+J10KLT

7-9
7.1.18. Removing the Inverter PCB, TS PCB 7.1.19. Removing the Antenna PCB L and R
and LCD Unit
LCD Rear Cabinet Ass'y
C W-LAN ANT Cover L
LCD Drop Holder Antenna PCB L

Connector
(CN201) Connector
(CN200)
TS PCB
LCD Drop
A Holder <N2>
B

<N2>
<N2>
<N2>
<N2>
<N2>
Antenna PCB R
Inverter PCB
LCD Unit <N6>
C W-LAN ANT Cover R
B <N6>
1. Remove the 4 Screws <N2>.
2. Remove the W-LAN ANT Cover L and R.
3. Remove the 2 Screws. <N2>
A 4. Remove the Antenna PCB L and R.

Screws <N2>: DRHM5054XA

to Connector
(CN200)
LCD Front Cabinet

1. Remove the 2 Screws. <N6>

2. Disconnect the 3 Cables from the 3 Connectors.
3. Remove the Inverter.
4. Disconnect the 2 Cables from the 2 Connectors.
(CN200,CN201)
5. Remove the TS PCB.
6. Remove the 2 Drop Holders.
7. Remove the LCD Unit.

Screws <N6>: DRQT26+E4FKL

7-10
7.2. Reassembly Instructions
7.2.1. Attention when CF-30 series is repaired
• Please execute writing BIOS ID when you exchange the Main Board.
• Parts (Sheet and rubber) etc. related various the Conductive Cloth and Heat Spreader cannot be recycled. Use new parts.

7.2.2. Setting the Antenna PCB L and R

1. Set the Antenna PCB L and R using the 2 Screws. <N2>
2. Fix the W-LAN ANT Cover L and R using the 4 Screws. LCD Rear Cabinet Ass'y
<N2> W-LAN ANT Cover L
Antenna PCB L
Screws <N2>: DRHM5054XA

<N2>

<N2>
<N2>
<N2>
<N2>
<N2>
Antenna PCB R

W-LAN ANT Cover R

7-11
■ Arranging the Antenna L and R Cables

Safety Working

S1:Insulation S2:Pinching Cables S3:Sharp Edge

CAUTION S4:Part No. Check S5:Others

Insert the cable between the pins. Insert the cable between the pins.

LCD REAR ASS'Y

REAR CABLE SHEET L

Put it along the inside of boss on X part
S2

Do not pinch the cable

out of the cabinet REAR CABLE SHEET R

Coming off the tape Do not pinch the cable

is arrowed S2
out of the cabinet
Attach it fitting
to the corner Cable color: gray

REAR SCREW SHEET

Cable color: black
Match it to the concave
side and attach it between
the bosses.

TAPE S2

Match it to the protrusion side and attach Do not pinch the cable
it betweenthe bosses. out of the cabinet

Tighten the screw Place the anntena main Place the anntena sub Tighten the screw

7-12
7.2.3. Setting the Inverter PCB, TS PCB and LCD Unit
1. Set the LCD Unit to the LCD Front Cabinet in order.
2. Attach the 2 drop holders. C
3. Connect the Cable to the Connector. (CN200,CN201) LCD Drop Holder
4. Connect the 3 Cables to the 3 Connectors. Connector
5. Fix the Inverter PCB using the 2 Screws. <N6> (CN201) Connector
(CN200)
TS PCB
Screws <N6>: DRQT26+E4FKL LCD Drop
A Holder
B

Inverter PCB
LCD Unit <N6>
C
B <N6>

to Connector
(CN200)
LCD Front Cabinet

7-13
■ Preparation of Inverter
* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2
2. When handling Inverter-PCB, do not bend or add impact.

Check the Part No.

N0GF1J000009(without T.S.) N0GF1J000009

Inverter Shield Case

S2
Prepare Inverter and the Inverter
shield case outside for assysite.
Inverter Shield Case Outside

N0GF2J000002

Check the Part No.

Wrap Inverter Shield Tape around Inverter
HBL-0361
Shield Case and attach.
Ensure that Inverter Shield Tape does not
run over the edge of Inverter Shield Case.

Inverter Shield Case is set <Inverter Shield Tapes Attachment Guide>

Inverter is set, Attach the Inverter Shield Tape Protorusion by wrinkles, etc. = 0.2 or less
attach Air Bubble = 1 cm 2 or less / 1 bubble size
Board attachment

Attach it putting the protrusion mark next to the caution label.

Match the board edge and the case edge.

Difference: 0.5mm or less

■ Assembly of LCD Unit

* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2

Confirm that the LCD

Cushion is not wrapped. LCD Drop Holder Insertion

Attach the Inverter MIL Shierd

LCD Front Ass'y

Match to the LCD
edge and attach it.

Clearance : 2 mm or less

LCD Drop Holder Insertion

0 0.5mm

7-14
7.2.4. Setting the LCD Rear Cabinet, Hinge L and R
1. Fix the Hinge L and R using the 2 Screws. <K9-1-4>
2. Set the LCD Latch. <N13>
left LCD Cover <N7>
3. Fix the LCD Rear Cabinet using the 4 Screws. <N7> No1 to Side Cover No.1
<N7>
No4 <N7> LCD Rear Cabinet
<N7>
4. Fix the left and right LCD Cover Side Cover using the 4 No.4
<N7> <N7>
Screws <N7> and 2 Screws. <N13>
5. Fix the 2 Wireless Antenna Corner Cover using the 4 No.3
<N7>
Screws. <N7> No.2 <N13>
<N7>
<N7>
Note: <N7>
Wireless Antenna
Tighten the Screws in the numbered order (No1 to No4). Corner Cover <N7>

Screws <N2>: DRHM5054XA LCD Latch <N7>

Screws <N7>: DRSB26+10HKL <K9-1-4> right LCD Cover
Screws <N13>: DRSB4+10FKL Hinge L Side Cover
Screws <K9-1-4>: DRYN4+J10KLT Wireless Antenna
Corner Cover
<K9-1-4>
Hinge R

LCD Front Cabinet

7-15
7.2.5. Setting the Display Unit
1. Fix the Display Unit using the 4 Screws. <N9> No1 to No4
2. Fix the Display Unit using the 2 Screws. <N10> No1, No2 Display Unit

Note:
Tighten the Screws in the numbered order (No1 to No2). No.1
<N9>
Tighten the Screws in the numbered order (No1 to No4).
No.4
<N9> No.3
Screws <N9>: DRYN4+J10FKL
<N9>
Screws <N10>: DXSB4+15FNLB
No.2
<N9>

No.1
<N10>

<N10>
No.2

7.2.6. Setting the Handle and Power SW

1. Set the WM SW using the 2 Screws. <K2-42>
2. Set the Power SW. <K2-41>
3. Set the Handle. Handle Base L
4. Fix the Handle Base L and R using the 2 Screws. <K2-41> Handle Base R
5.
<K2-41>

Screws <K2-41>: DRSN4+6FKLT

Screws <K2-42>: DXQT26+D4NLT
Handle

WM SW

<K2-42>

Power
SW

7-16
7.2.7. Setting the Palm Top Cover Sheet, Palm Top Cover, Touch Pad Adhesion Seat, Touch
Pad SW Knob, LED PCB And SW LED PCB
1. Set the SW LED PCB.
2. Attach the Power LED Packing Sheet to the LED Spacer
Sheet. Palm Top Cover Sheet
3. Attach the LEDX6 Spacer Sheet on the SW LED PCB.
4. Fix the SW LED PCB using the Screw. <K2-42>
5. Attach the PW LED Sheet. No.2
<N29>
6. Pass the Cable of LED PCB through the hole 1 on the Top
No.5
Cabinet, then set the LED PCB. No.4 <N29>No.1
<N29> <N29> No.3
7. Attach the LES Spacer Sheet on the LED PCB. <N29>
8. Set the touch Pad SW Knob In and Touch Pad SW Knob Palm Top Cover
9. Attach the TP Bottom Tape to the Touch Pad.
10. Pass the Cables of the Touch Pad through the hole 2 on the
Top Cabinet, set the touch Pad. Touch Pad Adhesion Seat
11. Attach the Touch Pad Adhesion Seat.
PW LED Sheet
12. Fix the Palm Top Cover using the 5 Screws. <N29> No1 to
No5 Touch Pad
13. Attach the Palm Top Cover Sheet.
<K2-42>
PW LED
Note: PCB
Tighten the Screws in the numbered order (No1 to No5). LED PCB
Touch Pad SW Knob SW LED
PCB
Screws <K2-42>: DRQT26+D4NLT
Screws <N29>: DRQT26+E3FNL
Touch Pad
SW Knob In

Hole 1
Hole 2

■ Preparation of SW LED FPC

* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2
0.5

Attach the Tape

0.5

Use a pinset. Attach it not to overlap the SW leg.

1 1
Flex Notch Standard 0 1
White Full Line : Mountain Fold

White Dotted Line : Valley Fold

Attach the Sheet

SW-LED FPC Ass'y

7-17
■ Assembly of Power SW
Top
Attach the Battery Cushion Connection Direction
Bottom

Battery Pack Insertion Slot

Cable Power
* Notes:
Connection
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2
CAB Wall
12 2

Connection Direction
25 2
3 5

Tighten of Screw

Attach the Battery Slide Sheet (on Battery Cushion)

FPC Power SW is set
Power SW LED
Panel is set Avoid air leaking into it. Avoid coming off 4 corners. S3
Safety Working
Fit to the line.
Attach the TP
FPC Tape
10 1

Match the Cabinet slit

and the tape slit.
Do not run the Cabinet
edge out of the tape slit.

Attach the DC Gasket

Ensure the upper and lower Flex holes match.

S1:Insulation S2:Pinching Cables S3:Sharp Edge

CAUTION S4:Part No. Check S5:Others

7-18
■ Assembly of Palm Top Cover

Using the pressure jig, Ensure the

loads are applied equally. Order of fixing
A
Make sure the adhesive materials
Screw Screw Screw
are attached closely on the whole
side. Screw Screw
Process the speaker lead wire not to B
put inside when applying the load.
Ensure that the PAD and the button neck Tighten of
are attached with adhesive firmly. Note: Separation Screw Tighten of
Tighten of
Screw
Screw

Touch Pad SW Knob Tighten of

Avoid running over the protrusion attached Insert FPC into the hole Touch Pad SW Knob In is set Screw Tighten of
to the protrusion side of the upper Cabinet. of upper cabinet. Rubber is set Screw
Notes for Separation

Attach the Pad

Attach the TP Palm Top Cover
Bottom Tape is set
Do not come over
the Pad edge. Do not attach the
oil on both sides.
Avoid running over!
Put to the arrow direction
and attach it.
Attach the Attach the Washer
Protrusion PWB 6LED Attach the Pad WP Sheet (See below)
Attach within the range of the
upper Cabinet concave.
Put to the left and set.

LEDX6 Spacer Insert FFC into the hole

Notes:
Sheet is set of upper cabinet.
After attaching, trace around TP,
SW and circumference with finger.
FFC 6LED is set

1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2

Attach the Washer

Attach it not to cover the hole
Palm Top of LEDX6 Spacer Sheet.
Cover
Palmtop Preparation

7-19
7.2.8. Setting the I/O PCB 7.2.9. Setting the SD PCB, Express Card
1. Open the Connector Cover and Lid Cover. and PCMCIA Card
2. Fix the I/O PCB using the 3 Screws. <N15> No1 to No3 1. Fix the PCMCIA Card using the 4 Screws. <N22>
3. Fix the I/O PCB using the 4 Screws. <N14> No1 to No4 2. Fix the Express Card using the 4 Screws. <N22>
4. Fix the I/O PCB using the 2 Screws. <N30> No1, No2 3. Fix the SD PCB using the 2 Screws. <N5>

No.1
Connector I/O PCB <N22> No.3 No.2
(CN701) No.2 <N22> No.4 <N22>
No.1 <N22> <N22>
Connector No.2
(CN700) <N15> No.2 <N30> No.1 No.4
No.1 <N22> <N22>
No.3<N15> <N14>
Connector Cover No.2 Express Card
<N15> No.4 <N30> No.3
<N14> <N22>
No.3
<N14>
No.2
<N6>
No.1
<N14> PCMCIA Card
No.1
<N6> SD PCB
LID
Cover

Note:
Tighten the Screws in the numbered order (No1 to No4).

Screws <N14>: DFHE5058ZB Screws <N6>: DRQT26+E4FKL

Screws <N15>; DRHM5104ZA Screws <N22>: DXQT2+G4FNL
Screws <N30>; DXHM0057ZA

7-20
7.2.10. Setting the Main PCB 17. Attach the Tape.
1. Fix the Main PCB using the 8 Screws <N6> and Screw. <N21>
Tape
<N11> No1 to No8. <N21>
Coin Battery Connector
2. Set the Modem Cable. Cushion MP Guide
(CN401) Connector
3. Connect the Cable to the Connector (J2) and fix the MDC. (CN400)
Coin Battery
4. Attach the Tape.
MP PCB <N6>
5. Attach the 1394 Sheet.
6. Fix the MDC using the 2 Screws. <N11> Connector <N6>
7. Fix the Modem LAN Case using the 2 Screws. <N6> (CN4)
8. Attach the 2 Modem Cable Sheets.
9. Fix the ICH Plate using the 3 Screws <N17> and Screw
<N11>.

<N17>

<N17> ICH Plate

No.2 Modem
<N17> Cable Sheet <N6>
<N6>
<N11>
No.5
<N6>
Tape <N6>
No.4
<N6> Connector
<N6> (CN11)
<N11> <N11> Connector
Modem
LAN Case (CN19)

MDC Connector Modem

(J2) Cable
18. Set the Main Chasis on the Computer.
No.8 19. Connect the Cable to the Connector (CN31) and Attach the
No.3 <N6>
<N6> Pet Tape.
20. Connect the Cable to the Connector. (CN700,CN701)
<N6> 21. Fix the Main Chasis using the 6 Screws <N16> No1 to No6
No.6
<N6> 22. Fix the Main Chasis using the Screw. <N18>
No.7 No.1
<N11>
<N18>
1394 Sheet
<N16>
<N16>
10. Connect the Cable to the Connector (CN4,CN11) to Connector(CN700)
<N16>
11. Attach the Tape. to Connector(CN701)
<N16> <N16> <N16>
12. Attach the Coin Battery.
13. Connect the Cable to the Connector. (CN19)
14. Attach the Coin Battery Cushion.
15. Fix the MP PCB and MP Guide using the 2 Screws <N6>
and 2 Screws. <N21>
16. Connect the Cable to the Connector. (CN400,CN401)
Connector(CN700) Main Chasis
Connector
(CN31)
Connector(CN701)
Pet Tape

23. Connect the 2 Cables to the 2 Connectors. (CN17,CN27)

7-21
 24. Fix the Screw. <N7>
25. Attach the TOP Screws.

TOP Screw Sheet

<N7>

Connector
(CN17)
Connector
(CN27)

Note:
Tighten the Screws in the numbered order (No1 to No8).
Tighten the Screws in the numbered order (No1 to No6).

Screws <N6>: DRQT26+E4FKL

Screws <N7>: DRSB26+10HKL
Screws <N11>: DFHE5025XA
Screws <N16>: DRQT26+E5FKL
Screws <N17>: DRQT26+E6FKL
Screws <N18>: DRSB26+8FKL
Screws <N21>: DXQT2+E12FNL

7-22
■ Assembly of LAN, Modem and MDC
* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2
S1:Insulation S2:Pinching Cables S3:Sharp Edge
CAUTION S4:Part No. Check S5:Others

Order of fixing
Tighten of
Screw Screw Screw
Tighten of Modem LAN Case
Screw is installed.

5 1
Pass the Cable to the back
from the hole of the A side.
15 1

LAN Cable
is installed.

Attach space

Separate from the coil.

Modem Cable Attach the DMD Cable Sheet S2 Process the cable and cover
is installed. Tighten of
(Remove 2 places)
Screw MDC Tighten of with MDM Cable Sheet
Screw
Match to the edge of the Connector. 1 Cable Coil
Safety Working

■ Assembly of Main PCB

* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2
S1:Insulation S2:Pinching Cables S3:Sharp Edge
CAUTION S4:Part No. Check S5:Others
Safety Working
Insert the connector wrapped with the
Attach the PET Sheet S3
Bend the cable avoiding the connector.
sheet into the connector on the board.
S3

Cable SATA Signal Insertion

1 2 Safety Working
Sheet wrap

0 1
0 1

Connect the LAN cable.

Put the cable ina a U-shape into the

intermediate chassis aperture next to the connector.

Do not pinch the cable out of the USB PCB.

Safety Working S2

7-23
7.2.11. Setting the PAD PCB
1. Fix the PAD PCB using the 2 Screws. <N29>
2. Attach the TP PCB Screw Sheet. TP PCB Screw Sheet
3. Connect the Cable to the Connector. (CN802)
4. Connect the Cable to the Connector (CN801) and attach
the Tape.
Tape <N29>

Screws <N29>: DRQT26+E3FNL

<N29>

Connector
(CN801)

Pad PCB

Connector
(CN802)

■ Assembly of PAD PCB

Order of fixing
* Notes: Screw Screw
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2

Insert the boss at an angle to put here close to the Cabinet side.

S1:Insulation S2:Pinching Cables S3:Sharp Edge

CAUTION S4:Part No. Check S5:Others Process the SP cable between the bosses.

FFC Insertion
PCB Pad is set
Safety Working
Attach the Touch Pad
Cable Hold Sheet PCB Screw Sheet S1
is installed

Safety Working
S2 Do not insert the Connector at an angle.
Safety Working S1 0 2

Attach the Touch Pad INS Sheet FFC Insertion

Avoid running over the boss and the rib. Attach the Touch
Tighten of
Pad FFC Fix Tape
Attach the Tape Screw 0 2
Fit to the Cabinet line. Tighten of
Screw
7 11
Safety Working S2

Safety Working S2 0 2
0 2 Attach the
Cable Sheet
Attach the Tape
Fit to the Cabinet line. 7 11

Process the surplus PCB Pad

of FFC to the back. LED PCB

Process the wire targeting the boss.

CN Connection After connecting, add the kapton tape.

7-24
7.2.12. Setting the FPC HDD BAT
1. Fix the FPC HDD BAT using the Screw. <N16>
to Connector (CN8)
2. Connect the 2 Cables to the 2 Connectors. (CN7,CN8) to Connector (CN7)
3. Connect the Cable to the Connector. (CN800) <N16>
4. Attach the PAD Protect Sheet. FPC HDD BAT

5. Connect the Cable to the Connector. (CN9) No.1

<N29>
6. Attach the Tape. No.4
No.2 to Connector (CN800)
7. Connect the 2 Cables to the 2 Connectors. (CN10,CN26) <N29> <N29>
No.3 Antenna Cable Sheet
8. Attach the Tape. <N29>
9. Attach the Antenna Cable Sheet on the Main PCB.
10. Fix the HDD FPC BAT using the 4 Screws. <N29> No1 to
No4 Tape to Connector (CN26)
HDD Cable Cover Connector(CN10)
Pad Protect
Sheet Connector(CN26)
Note:
Tighten the Screws in the numbered order (No1 to No4). Connector
(CN8)

Screw <N16>: DRQT26+E5FKL

Screw <N29>: DRQT26+E3FNL Tape

Connector
(CN7) Connector(CN9)

Connector (CN800)
Pad PCB

■ Preparation of HDD FPC ASSY

Order of fixing
Screw Screw Tighten of Tighten of
Screw Screw

Fold mountain based

on the white line.

Not to forget folding

Battery Guide
is set Battery Connector
PIN is set

Not to forget folding

Battery Connector PIN

Cushion is set

7-25
 1. Set HDD Guide and fix with Screw.
Tighten of Screw
2. Fix with Screw.
3. Apply tetra coating to each connector pin. Direction A
View

FPC HDD Battery is set

Do not Fold.
A (R1 4)

Direction B
View

Battery HDD Connector

Angle is set This Connector does not need tetra coating.
HDD Guide is set

Direction C
View

Tighten of Tighten of
Screw Screw

7-26
 Insert the Plug
into the Socket

The terminal of the antenna A

Relay Circuit Board Ass'y
cable must not come in
contact with this terminal.
Cable
(Put it on the metal fittings
side. )

Insert FPC into Relay Circuit Board Ass'ys socket

Figure seen from direction of arrow of A

Lock after FPC insertion

Mountain Fold (Straight Line)
Valley Fold (Dotted Line)

FPC

FIG

FPC

OK
The attention of folding : Breakage countermeasure.
1,The bending inside is R0.5 1
(R0.5 1) 2,Don't mistake a bending direction.
FPC Don't use a mistaken thing.

NG

7.2.13. Setting the USB PCB and Antenna PCB

1. Open the Connector Cover.
Tape
2. Fix the Antenna PCB using the 2 Screws. <N3> Connector
3. Connect the 2 white Cables. (CN100)

4. Fix the USB PCB using the Screws. <N6> <N6>

USB PCB
5. Connect the Cable to the Connector. (CN100)
6. Attach the Tape.
Antenna PCB
Screws <N3>: DRQT2+G6FKL
Antenna Cable Connector Cover
Screws <N6>: DRQT26+E4FKL (White) <N3>
<N3>

Antenna Cable
(White)

7-27
■ Assembly of USB PCB

* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2 S2 Safety Working S2 Safety Working
Attach the Tape Attach the Antenna Cable Sheet
Fit to the groove.
Set on the top. Difference : 1 or less Antenna Cable
Order of fixing
Screw Screw Process the cable from LCD. Tighten of Screw Plate is set

W-LAN Cable
Connection

EXT Antenna PCB

is set

Connect the coaxial cable from LCD.

Tighten of
Screw

Along the groove

Tighten of
Screw

Pull W-LAN Cable out to the surface from the hole.

S1:Insulation S2:Pinching Cables S3:Sharp Edge

CAUTION S4:Part No. Check S5:Others

* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2

Match to the board edge.

Difference: less than 1

Match to the CN edge.

Difference: less than 1

S1

Attach the kapton tape into CD Edge Sheet. Safety Working

PCB USB Sub is set

Tighten of Screw

Cable USB is set

7-28
7.2.14. Setting the DIMM Cover and Bottom Cover
1. Set the Bottom Cover.
No.5 No.2
2. Fix the Bottom Cover using the 6 Screws. <N8> No1 to No6 No.4 <N1> <N1> No.3
<N1> <N1>
3. Fix the Bottom Cover using the 11 Screws. <N6> No1 to
No11 DIMM Cover
4. Fix the Bottom Cover using the 2 Screws. <N17> No1, No2 No.1
<N1>
5. Set the DIMM memory card.
6. Attach the DIMM Heat Plate. <N6>
<N6>
7. Fix the DIMM Stopper Base using the 2 Screws. <N2>
DIMM Stopper Base
8. Fix the DIMM Cover using the 5 Screws. <N1>
DIMM Heat Plate
Screws <N1>: DRHM0002ZA
Screws <N5>: DRQT26+D4FKL DIMM Memory Card
Screws <N6>: DRQT26+E4FKL No.6
Screws <N8>: DRSB3+8FKL No.2 No.6 <N8>
No.7 <N8><N17> No.5
Screws <N17>: DRQT26+E6FKL <N17> No.5 <N6>
No.6 <N8> No.4
<N6> <N6>
No.7 No.4
Note: No.8 <N6>
<N6> <N8>
Tighten the Screws in the numbered order (No1 to No6). No.3
<N8> No.3
Tighten the Screws in the numbered order (No1 to No11). <N6>
Tighten the Screws in the numbered order (No1, No2). No.10
Tighten the Screws in the numbered order (No1 to No5). <N6>
No.9 No.2
<N6> No.11 <N6>
<N6> No.1
<N6>
Bottom Cover No.1
<N8>

7-29
■ Preparation of DIMM Cover
* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2

DIMM Cover is set

0 0.5mm

Attach the DIMM Cover Cushion

0 0.5mm

Attach the DIMM Cover Spacer

0 0.5mm

0 0.5mm

S1:Insulation S2:Pinching Cables S3:Sharp Edge S3

CAUTION S4:Part No. Check S5:Others

Safety Working
* Notes:
Keyboard Cable Cover is installed Attach the CD Edge Sheet
1. Apply the load when attaching the attaching parts. 20N to 30N (2 to 3Kgf)/cm2 0 1mm

4 6mm
LCD Cable Cover is set

4 6mm
1.5 2.5mm

Attach the CD Edge Sheet

S3

Attach the LCD Cable Cover Cushion Safety Working

Attach the Keyboard Cable Cover Cushion

7-30
7.2.15. Setting the GPS PCB and Bluetooth PCB
1. Fix the GPS BT Angle and GPS PCB using the 2 Screws.
<N12>
<N11>
2. Connect the Cable to the Connector on GPS PCB. <N12> <N12> GPS BT Angle
3. Fix the GPS Ass’y using the 4 Screws. <N12>
<N12>
4. Connect the Cable to the Connector. (CN25)
GPS PCB
Screws <N11>: DFHE5025XA
Screws <N12>: DXQT2+F3FNL Bluetooth
PCB
<N11>

<N11>

Connector(CN25)

to Connector
(CN25)

■ Cautions for Setting GPS ASSY and BT PCB ASSY

* Notes:
* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2
1. Do not gouge when inserting and removing the plug.
2. Do not damage the coating when handling the cable.
S2

Safety Working Attach the Tape Fit to the plate squeeze line. 1
Process the wire of whip ANT cable from
LCD to the back from the aperture.

Whip Antenna Cable

8 1
Put the Cable along
the Cabinet side and
tape it firmly. Main Antenna

Process the wire to the Sub Antenna

10 2 back from the aperture.
Match to the boss center. Insert the
Bluetooth Cable cable plug.

Pass the Cable behind

Cabinet Level Standard the Cabinet protrusion.
Tolerance 0 to 1
Process the wire into the groove.
GPS Antenna

S2 Safety Working Connect into the coaxial Connector.

Attach the Cable Sheet into

Attach the Cable Sheet into
Main Cable and Whip Cable. 0 2
Sub Cable and GPS Cable.
Safety Working S2

Ensure that the wrapping Avoid coming over the groove.

direction is right.
Bluetooth Cable
0 2 Ensure that the wrapping
direction is right.

Whip Antenna Cable Sub Antenna Cable

S1:Insulation S2:Pinching Cables S3:Sharp Edge
GPS Antenna Cable CAUTION S4:Part No. Check S5:Others
Main Antenna Cable

7-31
7.2.16. Setting the KB Cable Cover, Keyboard and LCD Cable Cover
1. Set the Keyboard onto the Computer.
2. Connect the 2 Cables to the 2 Cables. (CN13,CN14) No.3 No.5
<N29> <N29>
3. Fix the KB Cable Cover using the 7 Screws. <N29> No1 to No.1 No.7
No.4 <N29> <N29>
No7 to Connector <N29>
(CN14) No.2
4. Set the LCD Cable Plate. <N29>
5. Fix the LCD Cable Cover using the 3 Screws. <N29> No1 to KB Cable Cover
No.6
No3 <N29> No.2
<N29>
LCD
to Connector Cable Cover
Note: (CN13)
No.3
Tighten the Screws in the numbered order (No1 to No7). <N29>
Tighten the Screws in the numbered order (No1 to No3). No.1
<N29>

Screws <N29>: DRQT26+E3FNL

Keyboard
LCD
Cable Plate

Connector
(CN14)
Connector
(CN13)

■ Arranging the Keyboard

* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2

1. Attach the Keyboard US and Keyboard Spacer. (KB Preparation)

2. Attach the Keyboard Back Plate and Keyboard Spacer Sheet. (Plate Preparation)
Keyboard US is installed (Ensure Keyboard Spacer Sheet does not run over the level of Keyboard Back Plate.)
3. Attach the prepared KB to the prepared plate.
(Insert the KB protrusions into the plate holes and determine the position.)

Plate hole

Attach the Keyboard

Spacer Tape

Attach the Keyboard

Back Plate

Attach the Keyboard

Spacer Sheet

Attach the Keyboard Fook Spacer Lower

: Fit to the edge of plate (KBD back plate).

Both sides should not come over the plate.

7-32
7.2.17. Setting the KB Cover, Hinge Cover L, Hinge Cover R and Keyboard
1. Insert the front hooks of the Keyboard to the Top Cabinet in
order, and set the Keyboard. No.3 <N6>
<N6>
2. Fix the Hinge Cover L and R using the 3 Screws <N6> No1 Bluetooth PCB
No.1
to No3 <N6>
3. Fix the Hinge Cover L and R using the 2 Screws. <N2> No.2 No.1 No.2
<N6> <N6> <N2>
No1, No2 No.4 Hinge Cover L
4. Fix the Bluetooth PCB using the Screw. <N6> <N6>
No.2 No.3
5. Fix the KB Cover using the 4 Screws. <N6> No1 to No4 <N6> <N6>
KB Cover No.1
Note: <N2>
Tighten the Screws in the numbered order (No1 to No4).
Tighten the Screws in the numbered order (No1 to No3).
Tighten the Screws in the numbered order (No1, No2).
Hinge Cover R
Screws <N2>: DRHM5054XA
Screws <N6>: DRQT26+E4FKL

Keyboard

7.2.18. Setting the HDD

1. Set the HDD FPC to HDD.
2. Attach the Heater Ins Sheet and Sheet to HDD. HDD U Case Ass'y
3. Attach the Heater to HDD. <K1-17> <K1-17>
4. Attach the 6 HDD Forming MFYPC and the two HDD HDD FPC
Terminal Plate Upper to the HDD Damper Ass'y.
5. Attach the six HDD Forming MFYPC and the two HDD
Terminal Plate Upper to the HDD Damper Ass'y. HDD
SATA Guard
6. Set the HDD Damper Ass'y to HDD.
7. Attach the Side Cushion to the HDD L Case Ass'y. <K1-16>
8. Set the HDD U Case Ass'y and the HDD L Case Ass'y, and
set the two Tabs of the HDD L Case Ass'y. Heater Ins Sheet Sheet
9. Fix the HDD U Case Ass'y and the HDD L Case Ass'y using
the 4 Screws <K1-17> and Screw <K1-16>.
HDD
Screws <K1-16>: DFHE5025XA Damper
Screws <K1-17>: DRQT2+E8FKL Ass'y

Heater

HDD L
Case Ass'y

7-33
■ Preparation oh HDD ASSY
* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2

HDD TAPE S
Fit to the corner.
HDD INS SHEET

Turn it to the board side (back side).

1. Do not gouge when inserting and removing the socket.

2. Do not drop HDD or add any impacts on it.
3. Insert CN into the end firmly.
4. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2

Safety Working
S1:Insulation S2:Pinching Cables S3:Sharp Edge
S4
Attach it pushing the shaded CAUTION S4:Part No. Check S5:Others
HEATER part not to push the fuse.

Valley Fold
Mountain Fold
Do not bend the bending
part of Heater
PET TAPE
HEATER FIXED
TAPE Center
Connect the Connector

Insert the HDD FPC Ass'y

7-34
 * Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2

Do not place the damper Do not place the damper

over the plate of FPC. over the plate of heater.

HDD Damper Ass'y

Make sure the product with black

sheet on the yellow sponge.

Fold the FPC from the board edge.

Push and bend

HDD Ass'y
HDD Set Insert after removing the Release Paper of the two-sided tape.
Remove the Release Paper on
the back, close and attach it.

Attach it to HDD closely not to loosen.

* Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2
When attaching HDD Cushion (Yellow) and HDD Cushion (Black),
set the bending part of the metal plate up.
1

HDD Thermal Plate 1 3

0

1 3
Do not bend it at a sharp
angle to put natural R.
3
3

1
1

HDD Cushion (Black)

2
1

Metal Plate

Longer Direction
To the level of attaching
closely in this range

Attach the HDD Cushion (Yelllow)

Attach the HDD Cushion (Yelllow)

Attach the HDD Cushion

(Black)
Attach the HDD
Thermal Plate
Sheet

Prepare the metal plate bend.

7-35
 When attaching HDD Cushion Plate and HDD Cushion (Black),
* Notes:
set the bending part of the metal plate up.
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2

1
1 3 1 3

0
HDD Thermal Plate

1 3
0
1 3
Do not bend it at a sharp HDD Cushion
angle to put natural R.
(Black)
Metal Plate
Longer Direction

To the level of attaching

closely in this range
Attach the HDD Cushion (Yellow)

Attach the HDD Cushion (Yellow)

Attach the HDD Cushion (Black)

Attach the HDD thermal Plate

*Ensure the direction is right. (lateral) Put the edge on the same line.
Difference: 1

7-36
 * Notes:
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2

Make the black damper get int

both sides of the green dampe

Right and left position: Match to the center

Top and bottom position: Match the edge of the base material transparent
A sheet to the bottom side

(20)

HDD Side Damper is installed (0)

Paste the cushion with pressing

in the direction of arrow.

A HDD Side Damper Lower Case

(2)

B B

0 0.5

(Entire Circumference)

B-B SEC A-A SEC

HDD Bottom Case Ass'y

7-37
 Set the CN side first, and then set the
TAB side pushing to the A direction.

SATA Guide Set

HDD Ass'y insertion

SATA Guard is installed

Insert to make the Cushion on the HDD

inside of the Cushion on the lower case.

Avoid getting HDD under the side

NG damper when inserting HDD

* Notes:
Order of fixing
1. Apply the load when attaching the parts. 20N to 30N (2 to 3Kgf)/cm2 Screw Screw Screw Screw

Tighten of Screw

Tighten of
Screw

Tighten of
Screw Tighten of
Screw

Tighten of
Screw

Confirm that the CN board moves up/down

and right/left after assembling.

7-38
7.2.19. Setting the Battery Pack and HDD Pack
1. Set the HDD Pack.
2. Set the Battery Pack.

Battery
Cover

HDD Cover

Battery Pack

HDD Pack

7-39
10 Exploded View
K82 K77 B N6
K76 K78
B N2
E2 B N6
B B N2
E1001 N6

K32 B N6
A K35
A
N29 K33
N29 A K1210
N29 B
B N29
N29

K2
K74
K116
K2-48 K70
K29
K93 K16
K75
R K2-42
K2-49
E24 K2-46
K35
E4
K84
K2-45 K59 K71
K90

K59
K92 B
E21 E13 E23
N29
B B B
K53 N29 N29
B N29 K30
B N29
K109 N7 G
K19 N10 B
N29
B
K1122 K1201 K35
V N29
V
G
N10 K17 K1

K1-17
K1-3
K1-17
K2 K1-1
K1-16
K1214 K1-20 K1-4
K129 E17 K1-4 K1-19
K1-9 K1-19

K1-8 K1-5
K25
Screw tightening torque K1-5
K26
A 0.19 +
_ 0.02 N.m K1-11
K25 K1-18
+ 0.2 kgf.cm)
(2.0 _
K25 K1-14
B 0.45 +
_ 0.05 N.m K1202
(4.5 +
_ 0.5 kgf.cm) K1-20
F 0.49 +
_ 0.05 N.m K1-6
K1-15 K1-4
(5.0 +
_ 0.5 kgf.cm)
K1-4
G 1.47 +
_ 0.20 N.m
(15 +
_ 2.0 kgf.cm) K1-13 K1-6

I 0.18 +
_ 0.22 N.m
K1-2
(2.0 +
_ 0.2 kgf.cm)
L 0.2 +
_ 0.02 N.m + 0.05 N.m
R 0.3 _
(2.0 +
_ 0.2 kgf.cm) + 0.5 kgf.cm)
(3 _

CF-30FTSAZAM
 R K2-16 R
K2-3 K2-16
K2-6
K2-5
K2-5-3 K2-10
R K2-6-2
K2-5-1
K2-6-5 K2-6-1 B
K2-3-2 K2-3-3 K2-10-8
K2-5-2
K2-3-1 K2-10-1
K2-6-4 K2-10-3
L K2-3-4
K2-5-4
K2-6-1
L K2-39
B
R
K2-6-3 K2-10-5 K2-10-8
R K2-39 K2-10-2
K2-6-3
K2-10-1
U N17
K112
K104
K101
B K81 R
K100 K2-10-4
K2-8 K2-8-10 K2-39
K2-10-6
K2-8-2 R K2-4
K2-8-1 B K2-10-7
R K122 K2-10-8 K2-16
K2-8-5 K2-8-4 K2-39
K2-8-6 K2-8-3 B N29
B
K2-8-7
K2-8-10 K2-36 K2-14 K2-23
K2-8-9 K2-4-3
K2-8-1 K2-43 K2-30
T
R K2-17 K2-4-1
K2-8-8 R K2-16 K2-47
K2-39 K2-4-2
K2-8-3 K2-13 K2-4-4
L
L K2-8-11 K2-22

T K2-38 K2-17 K2-14

K2-18
R K2-16
K2-22
K2-25
K108
K2-50 K2-21 K102 K103 K163
K107 K2-15
K2-50 K2-18 K114
K2-50 K2-36
T K2-38
T
K2-24 K2-20 K105 K121
K36 K2-43
K2 G
K2-25 K106
K2-26 K2-31 K113
K2-41 K2-44
K2-1 R K2-42
Screw tightening torque B N29
A 0.19 ± 0.02 N.m K2-1-3
(2.0 ± 0.2 kgf.cm) K2-1-2
K2-1-1 K2-37 L K2-2-7
K2-2
B 0.45 ± 0.05 N.m K2-41
(4.5 ± 0.5 kgf.cm) G K2-2-3
K2-27 R
K2-2-6
G 1.47 ± 0.20 N.m K2-2-2
(15.0 ± 2.0 kgf.cm) L K2-9-5 K2-9-8
K2-42 K2-7
K2-2-5
L 0.2 ± 0.02 N.m K2-9-9 L K2-2-1
(2.0 ± 0.2kgf.cm) K2-9-9 K2-2-4
R K2-7-1
Q 0.22 ± 0.02 N.m K2-42 K2-7-2
(2.2 ± 0.2 kgf.cm) L K2-9-2 K2-9-7 K2-7-3
K2-9-9
R 0.30 ± 0.05 N.m K2-9-1 K2-9-4 K2-9 K2-7-1
K2-9-6
(3.0 ± 0.5 kgf.cm)
K2-9-1
T 0.90 ± 0.05 N.m B
(9.0 ± 0.5 kgf.cm) K2-39 K2-7-4
K2-39 R R
U 0.33 ± 0.03 N.m
R K2-9-3 K2-9-10
(3.3 ± 0.3 kgf.cm)

CF-30FTSAZAM
 F
N14
A
N30 F A N15
N14
A N15
A N15
A N3

K83
V
W
K157 K1211
B N11

E1
K2-11 K132
K2-29 E19

E8
K117
E38
K97 W
K97 E22 K1123
K2-12 K91
K2-19
K2-28 K130
R K2-40 B N29
V
E10 K38 B N29
K135
N11 B N29 A
N11 B N11
E20 B N17 K36
K148 N17
K1208
B
K149 K1206
K123 N17
B N29
K118 K21 B B N6 K1208
Screw tightening torque A N6 K144
K99 K96
A 0.19 +
_ 0.02 N.m N22 K153 B N6 K1207
K1214
(2.0 _
+ 0.2 kgf.cm) K97
A A K1214
B 0.45 +
_ 0.05 N.m A N22 N22 K1205 K137
A
(4.5 +
_ 0.5 kgf.cm) N22 A
N22 B
N22 B K35
C 0.216 + _ 0.0196 N.m N6 B
N6 N6
(2.2 +_ 0.2 kgf.cm) E33 E32 B N6
K1203 A
E 0.314 + _ 0.0196 N.m A N22 K1214 E29 E3 N11
(3.2 +_ 0.2 kgf.cm) K145
K143
F 0.49 +_ 0.05 N.m K133 K1209
B
(5.0 +_ 0.5 kgf.cm) K134 K139 N16
K141
G 0.441 + _ 0.049 N.m E34 K149
K146 E26
(4.5 +_ 0.5 kgf.cm) K153 B E31
H 1.47 +_ 0.20 N.m K138 B
N6 E28
(15 +_ 2.0 kgf.cm) N16
B
B B
I 1.30 +_ 0.17N.m A N19 N16 E11 K1155
N16 N18
(13 +_ 2.0 kgf.cm) A
K111 K110 B N16 N11 K94
L 0.18 +_ 0.02 N.m K119 K34 B K140 E18
(2.0 +_ 0.2 kgf.cm) K86 N29 B K131
K161 K142 E25 K36
M 0.2 +_ 0.02 N.m N16 K1204
K86 K1212
A
(2.0 +_ 0.2 kgf.cm) B K27 A
N16 N21 E9
N 0.45 +_ 0.03 N.m K119 E5 Q N6 N21 B K35
(4.5 +_ 0.3 kgf.cm) K124 B N6
A N20 Q N6 N6 E12
E27
P 0.8 +_ 0.1 N.m A N20
K22 K148 K35 E30
(8.0 +_ 1.0 kgf.cm) E27 K148 B N6
K35
Q 0.22 _+ 0.2 N.m
(2.2 _
+ 2.0 kgf.cm)

CF-30FTSAZAM
 S N12 S N12
E2

K41

K42
E39 K40

K118 E14

A N11

K3
K28
R R K3-8
K3-8
K2-33 K3-3 R K18
K3-4 K3-8
K2-32 R K3-8 R K3-2 K3-7
K3-3 K3-6 K3-9

K3-5 X
R K2-39 R K3-4 K31
K2-34 K2-39 B N1
K3-1
K85
B N1
P N8
B
B B
N6 B N1
N6 N6 B N1
B B N1
N6
B N6
X

P N8
K85
K85 P N8
B
B
N6 B
B N17
B
N17
N6 B
B N6 Screw tightening torque
N6 P
K4 N6
N8 K85 B 0.45 +_ 0.05 N.m
P N8
(4.5 _
+ 0.5 kgf.cm)
P 0.8 +
_ 0.1N.m
K5
(8.0 +
_ 1.0 kgf.cm)
R 0.3 +
_ 0.05 N.m
(3.0 +
_ 0.5 kgf.cm)
K80 S 0.19 +_ 0.05 N.m
(2.0 +
_ 0.5 kgf.cm)
K1213

CF-30FTSAZAM
 K36

K50 K36

K9

K61

K9-2-1-1
K9-2

K9-2-2 K50

K9-2-3

K60
G N9
K63

K10 K62
K9-1-3

K10-1 K65

K10-2 K12
B N6
K11 K49
K9-1-2 G E16
K9-1-4
K9- K9-4
K9- 1-3
K9-3
1-3
K9-1-3 K1151

G N9
Screw tightening torque
A 0.19 _+ 0.02 N.m
K9-1 (2.0 +
_ 0.2 kgf.cm)
B 0.45 _+ 0.50 N.m
K9-1-1 (4.5 +
_ 0.5 kgf.cm)
K9-1-3 F 0.441 +_ 0.049 N.m
G (4.5 +
_ 0.5 kgf.cm)
K9-1-4
G 1.47 _+ 0.20 N.m
(15 +
_ 2.0 kgf.cm)
K9-1-3
H 1.30 _+ 0.17N.m
(13.0 +_ 2.0 kgf.cm)

CF-30FTSAZAM
 K54

E35

E35-2
E35-5
A
E35-10
E35-8

E4
E15 K56

E35-1
K1214
E35-3

E35-4 K1214

E35-6

E35-4
E35-7
K1214
E35-3

A E35-10

E35-9

K1214

Screw tightening torque

A 0.19 +
_ 0.02 N.m
+ 0.2 kgf.cm)
(2.0 _
B 0.45 +
_ 0.05 N.m
(4.5 _
+ 0.5 kgf.cm)
C 0.216 +_ 0.0196 N.m
(2.2 +
_ 0.2 kgf.cm)
D 0.314 +_ 0.0196 N.m
(3.2 +
_ 0.2 kgf.cm)
E 0.49 +
_ 0.05 N.m
(5.0 +
_ 0.5 kgf.cm)

CF-30FTSAZAM
 B
B N7 N2 B
N2
K44 B
N7 K57 B
N2 B
B N2
N2
B K58
N7
B
K1031 E36 N2 B
B N7 K79
N7 E37 B
N7
B
G N7
N13
K13 K13-2
B N7

K46 K45
K97
K52 B N7

B N7
K47
K1032 G N13

K13-1

B N7 B
N7
Screw tightening torque
A 0.19 +_ 0.02 N.m
(2.0 +
_ 0.2 kgf.cm)
B 0.45 +_ 0.05 N.m
(4.5 +
_ 0.5 kgf.cm)
C 0.216 +_ 0.0196 N.m
(2.2 +
_ 0.2 kgf.cm)
D 0.314 +_ 0.0196 N.m
(3.2 +
_ 0.2 kgf.cm)
G 1.47 +_ 0.20 N.m
(15 +
_ 2.0 kgf.cm)
O 0.49 +_ 0.05 N.m
(5.0 +
_ 0.5 kgf.cm)

CF-30FTSAZAM
Replacement Parts List
Note : Important Safety Notice
Components identified by mark have special characteristics important for safety.
When replacing any of these components, use only manufacturer's specified parts.

CF-30FTSAZAM
REF. NO and AREA PART NO. DESCRIPTION Q'TY
Main Block Unit
E1 DL3UP1336BAA PCB, EXT ANT RTL 1
E2 DL3UP1354CAA PCB, BT ANT UNIT RTL 1
E3 DL3UP1630AAA PCB, MAIN UNIT FOR MK2 RTL 1
E4 DFWP0150ZA SW-LED FPC UNIT 1
E5 DL3UP1543AAA HDD BATTERY FPC UNIT 1
E7 DL3UP1580AAA PCB, TOUCH PANEL CONTROLLER RTL 1
E8 DL3U11540BAA PCB, IO RTL 1
E9 DL3U21540BAA PCB, MP RTL 1
E10 DL3U31540BAA PCB, PAD RTL 1
E11 DL3U41540BAA PCB, SD RTL 1
E12 DL3U61540BAA PCB, USB RTL 1
E13 DL3U71540BAA PCB, LED RTL 1
E14 DFJK10U050BB FFC 1
E15 DFJS1031XA LCD CABLE 1
E16 S N0GF2J000002 INVERTER 1
E17 S N3CAYYY00030 HDD, 80GB 5400RPM SATA 1
E18 N5ZZ00000129 SO-DIMM, DDR2-667 1GB 1
E19 DFJS1049ZA W-LAN CABLE 1
E20 S N5HZC0000031 WIRELESS LAN MODULE 1
E21 DFJK10T017BB FFC 1
E22 DFJK40T030BB FFC IO40 1
E23 DFJS1037ZB POWER CABLE 1
E24 N2EABEC00006 TOUCHPAD 1
E25 BR-2330A/SF LITHIUM COIN BATTERY 1
E26 DFJK12U050BB FFC SD 1
E27 DFJK40U056BB FFC MP OUTER 2
E28 DFJS1032YA MODEM CABLE 1
E29 DFJS1035YA SATA CABLE 1
E30 DFJS1036ZA CABLE USB 1
E31 DFJS1046YA LAN CABLE 1
E32 K1NA26Z00001 CONNECTOR 1
E33 K1NA68Z00009 PCMCIA CONNECTOR 1
E34 S N5HAZ0000014 MODEM 1
E35 DFWV08A0090 LCD UNIT ASS'Y 1
E35-1 DL3DE0183AAA LCD PREPARATION UNIT 1
E35-2 DFHG1926YA LCD SIDE DAMPER(U) 1
E35-3 DFHG1927ZA TS SPACER(L) 2
E35-4 DFHG1928ZA TS SPACER(S) 2
E35-5 DFHG1882YA LCD DMP L 1
E35-6 DFHG1883YB LCD SIDE DMP R 1
E35-7 DFMD3130ZA LCD HOLD PLATE L 1
E35-8 DFMD3131ZA LCD HOLD PLATE R 1
E35-9 S L9DZYY000006 HEATER(LCD) 1
E35-10 DXYN2+C3FNL SCREW 2
E36 N1ZYYY000005 WLAN MAIN ANTENNA 1
E37 N1ZYYY000006 WLAN SUB ANTENNA 1
E38 DFUP1565ZA FPC 1
E39 DL3UP1635BAA BT PWB UNIT FOR 30MK2 RTL 1
E1001 N2ABZY000035 KEYBOARD VISTA, U.S. 1
Accessories
A1 S NCR-B/901A LITHIUM ION BATTERY PACK 1
A2 S CF-AA1653ASA AC ADAPTOR 1
A3 DFHR6207ZA PEN 1
A4 DFHS9017ZA TOUCHPANEL CLOTH 1
A5 DFME0148YA PEN TETHER 1
A6 S DFQW5098ZA MANUAL(CF30MK2M XP) 1
A7 S K2CG3DR00003 AC CORD 1
A8 DFJS954ZA MODEM CABLE 1
A21 DFHR6339ZA-0 DUMMY EXPRESS CARD 1
A22 DFHR6340ZA-0 DUMMY PC CARD 1
A23 S DFKE0911ZC-0 MP DUMMY CASE 1
A91 DFQM8357MA RECOVERY DVD, VISTA 1
Packing Material
P1 DFPH0064ZA PACKING PAPER 1
P2 DFPP0143ZA PROTECTION BAG 1
P3 DFPE0852ZA MANUAL HOLDER 1
P4 DFPN0845ZA DB CUSHION 1
P5 DFPK1202WA PACKING CASE(OVERSEAS) 1
Mechanical Parts
K1 DFWV99A0125 HDD MOUNTING KIT 1
K1-1 DL3UP1557AAA HDD PACK FPC UNIT 1
K1-2 DFMD8041YA HDD LOWER CASE ASS'Y 1
K1-3 DFMD8042YA HDD UPPER CASE ASS'Y 1
K1-4 DFHG1750YB HDD CUSHION(YELLOW) 4
K1-5 DFHG1933ZA FIX CORE CUSHION 2
K1-6 DFHG1934ZA HDD FORMING M2 2
K1-8 DFHP7101ZA DOUBLE SIDE TAPE(7X30) 1
K1-9 DFHR6264ZA SATA GUARD 1
K1-11 DFMX0634ZA CD EDGE SHEET 1
K1-13 S L9DZYY000008 HEATER(HDD) 1
K1-14 DFHR8522XA HDD DAMPER ASS'Y 1
K1-15 DFHR8523WA HDD SIDE DAMPER ASS'Y 1
K1-16 DFHE5025XA SCREW 1
K1-17 DRQT2+E8FKL SCREW 4
K1-18 DFMX1265ZB HEATER INS SHEET 1
K1-19 DFHR3H11ZA HDD CUSHION TOP SHEET 2
K1-20 DFMY3263ZA HDD THERMAL PLATE LOWER 2
K2 S DFKM8183TA-0 TOP CASE ASS'Y 1
K2-1 DFBD9010ZA-0 POWER SW ASS'Y 1
K2-1-1 DFHR6251ZA-0 POWER SW FLAME 1
K2-1-2 DFHR6252ZA-0 POWER SW KNOB 1
K2-1-3 DFUQ0114ZA POWER SW KNOB SPRING 1
K2-2 DFBD9011XA-0 WIRELESS OFF SW ASS'Y 1
K2-2-1 DFHG1885YA WM SW CUSHION 1
K2-2-2 DFHP7140ZAT TAPE 1
K2-2-3 DFHR3D54ZA-0 WM SW SHEET 1
K2-2-4 DFHR6257ZB WIRELESS SW CASE 1
K2-2-5 DFHR6258ZA-0 WIRELESS SW KNOB 1
K2-2-6 DFMD7B10YA WM OFF SW PLATE 1
K2-2-7 XTB2+4GFN SCREW 1
K2-3 S DFKE8185ZA-0 MP LATCH ASS'Y 1
K2-3-1 DFBD0190ZA-0 MP LATCH LEVER 1
K2-3-2 S DFKE0861ZA-0 MP LATCH CASE 1
K2-3-3 DFUQ0113ZA SD LATCH SPRING 1
K2-3-4 DRHM0110ZAT SCREW 2
K2-4 S DFKE8186ZA-0 SD LATCH ASS'Y 1
K2-4-1 DFBD0192ZA-0 SD LATCH LEVER 1
K2-4-2 S DFKE0867ZA-0 SD LATCH CASE 1
 K2-4-3 DFUQ0113ZA SD LATCH SPRING 1
K2-5-4 DRHM0110ZAT SCREW 2
K2-5 S DFKE8187YA-0 CN LATCH ASS'Y 1
K2-5-1 DFBD0193ZA-0 CN LATCH LEVER 1
K2-5-2 S DFKE0869YA-0 CN LATCH CASE 1
K2-5-3 DFUQ0116ZA CN LATCH SPRING 1
K2-5-4 DRHM0110ZAT SCREW 3
K2-6 S DFKE8188ZA-0 MP COVER ASS'Y 1
K2-6-1 DFBH3051ZA LID HINGE 3
K2-6-2 DFGE0139ZA-0 MP COVER SHEET 1
K2-6-3 DFHR3E55ZA MP COVER CUSHON 2
K2-6-4 S DFKE0860ZA-0 MP COVER 1
K2-6-5 DRQT26+D3KLT SCREW 3
K2-7 S DFKE8189YA-0 SD COVER ASS'Y SDHC 1
K2-7-1 DFBH3051ZA LID HINGE 2
K2-7-2 DFGE0140YA-0 SD COVER SHEET 1
K2-7-3 S DFKE0866ZA-0 SD COVER 1
K2-7-4 DRQT26+D3KLT SCREW 2
K2-8 S DFKE8190XB-0 BATT COVER ASS'Y 1
K2-8-1 DFBH3051ZA LID HINGE 2
K2-8-2 DFGE0141ZA-0 BATT COVER SHEET 1
K2-8-3 DFHR3E56ZA BATT COVER CUSHION 2
K2-8-4 DFHR3E59ZA BATT LID KNOB SHEET 1
K2-8-5 S DFKE0799ZA-0 LID KNOB 1
K2-8-6 S DFKE0862XA-0 BATT COVER 1
K2-8-7 DFMD7B12ZA BATT LATCH ANGLE 1
K2-8-8 DFUN0084XA BATT LATCH SPRING 1
K2-8-9 DFUS0323ZA LID KNOB SPRING PLATE 1
K2-8-10 DRQT26+D3KLT SCREW 2
K2-8-11 DXQT2+F3FNLT SCREW 1
K2-9 S DFKE8191YA-0 HDD COVER ASS'Y 1
K2-9-1 DFBH3051ZA LID HINGE 2
K2-9-2 DFBD0191ZA-0 HDD COVER LOCK KNOB 1
K2-9-3 DFGE0149ZA-0 HDD COVER SHEET L 1
K2-9-4 DFGE0150ZA-0 HDD COVER SHEET R 1
K2-9-5 DFHR3E57ZA HDD COVER CUSHION 1
K2-9-6 S DFKE0864YA-0 HDD COVER 1
K2-9-7 S DFKE0865ZA-0 HDD COVER LID KNOB 1
K2-9-8 DFUS0311ZA HDD COVER SPRING PLATE 1
K2-9-9 DRQT2+D25KMT SCREW 4
K2-9-10 DRQT26+D3KLT SCREW 2
K2-10 S DFKE8192ZA-0 CN COVER ASS'Y 1
K2-10-1 DFBH3051ZA LID HINGE 2
K2-10-2 DFGE0143ZA-0 CN COVER SHEET L 1
K2-10-3 DFGE0144ZA-0 CN COVER SHEET R 1
K2-10-4 DFHR3E58ZA CN PACKIN-SLIDE 1
K2-10-5 S DFKE0868ZA-0 CN COVER 1
K2-10-6 S DFKE0875ZA-0 CN SLIDE COVER 1
K2-10-7 DFMD7B11ZA CN WATER PROOF PLATE 1
K2-10-8 DRQT26+D3KLT SCREW 3
K2-11 DFJS1030ZA SP CABLE 1
K2-12 L0AA04C00012 SPEAKER 1
K2-13 DFGE0111YA-0 TOP LOOK SHEET 1
K2-14 DFGE0145ZA-0 REAR BELT COVER SHEET 2
K2-15 DFGL0153ZB-0 SD LED SHEET (NO SC) 1
K2-16 DFHE5121YA SCREW 8
K2-17 DFHG1699ZA LCD LOCK SHEET 2
K2-18 DFHG1891ZA HANDLE ARM CUSHION 2
K2-19 DFHG1892YA SPEAKER CASE CUSHION 1
 K2-20 DFHG1931ZA WM SW CASE CUSHION 1
K2-21 DFHG1973ZAT SD SHEET SPACER TW 1
K2-22 DFHM0419YA LCD FOOT CAP 2
K2-23 DFHR3D56ZA-0 CN COVER SHEET 1
K2-24 DFHR3E66ZA POWER SW CUSHION 1
K2-25 DFHR6291YB-0 FRONT BELT COVER 2
K2-26 S DFKE0851ZB-0 HANDLE BASE L 1
K2-27 S DFKE0852ZB-0 HANDLE BASE R 1
K2-28 S DFKE0856ZB-0 SPEAKER CASE A 1
K2-29 S DFKE0876ZB SPEAKER CASE B 1
K2-30 S DFKM0516WA-0 TOP CASE 1
K2-31 DFMD2170ZA KENSINGTON PLATE 1
K2-32 DFMD2172ZA HEAT PIPE ANGLE A 1
K2-33 DFMY0414ZA CPU HEAR PIPE RUBBER 1
K2-34 DFMY5037ZA HEAT PIPE UNIT A(TOP) 1
K2-36 DFUQ0102ZA POTRE SPRING 2
K2-37 DFWP0145YA FPC 1
K2-38 DRHM0118ZAT SCREW 2
K2-39 DRQT26+D3KLT SCREW 15
K2-40 DRQT26+D5KLT SCREW 4
K2-41 DRSN4+6FKLT SCREW 2
K2-42 DXQT26+D4NLT TW SCREW 4
K2-43 DXQT3+F4FNLT SCREW 2
K2-44 DFKH8009YA-0 HANDLE ASS'Y 1
K2-45 DFHP7140ZAT DOUBLE SIDE TAPE 1
K2-46 DFHR3G74ZAT PW SW CUSHION 1
K2-47 DFHR3K43ZAT LCD HINGE SPACER 1
K2-48 DFHR3E97ZA P LED SHEET 1
K2-49 DFHR6356ZA POWER SW LED PANEL TW 1
K2-50 DFHR6089YA-0 HANDLE ARM BUSH 4
K3 S DFKF8170YA-0 BOTTOM CASE ASS'Y 1
K3-1 S DFKF0271YA-0 BOTTOM CASE 1
K3-2 DFMD2172ZA HEAT PIPE ANGLE A 1
K3-3 DFMD2173ZA HEAT PIPE ANGLE B 2
K3-4 DFMY0414ZA CPU HEAR PIPE RUBBER 2
K3-5 DFMY0437ZA HEAT PIPE RUBBER B 1
K3-6 DFMY5038YA HEAT SINK UNIT C 1
K3-7 DFUS0324ZA MP ESD SPRING 1
K3-8 DRQT26+D3KLT SCREW 6
K3-9 DXQT26+D4NLT TW SCREW 2
K4 DFGE0087ZA-0 BOTTOM COVER SHEET D 1
K5 DFGE0138ZA BOTTOM CASE SHEET 1
K9 DFWV80A0403 LCD FRONT CABINET/TS PANEL ASS'Y 1
K9-1 S DFKF8171VA-0 LCD FRONT ASS'Y 1
K9-1-1 DFBH1180ZB HINGE ASS'Y R 1
K9-1-2 DFBH1181ZB HINGE ASS'Y L 1
K9-1-3 DFHR3E61YA TS DUMPER PC 8
K9-1-4 DRYN4+J10KLT SCREW 2
K9-2 DFWV84A0310 TOUCH SCREEN PANEL KIT 1
K9-2-1-1 DFHR9068ZA PROTECTIVE FILM 1
K9-2-2 DFHP7246ZA TS FIXED TAPE 1
K9-2-3 DFHR3695ZA TS FPC SPACER 1
K9-3 DFHE0843ZA LCD MAGNET 1
K9-4 DFHG1929ZA MAGNET CUSHION 1
K10 DFBS8003ZA-0 LCD LATCH ASS'Y 1
K10-1 DFBS0073ZA-0 LCD LATCH 1
K10-2 DFHR6313ZA LCD LATCH SLIDER 1
K11 DFDF5024ZA LCD LATCH SHAFT 1
K12 DFUN0083ZA LCD LATCH SPRING 1
 K13 DFWV80C0513 LCD REAR CABINET ASS'Y 1
K13-1 S DFKM8184ZA-0 LCD REAR ASS'Y 1
K13-1-1 S DFKM0517ZA-0 LCD REAR CAB 1
K13-2 DFGB0131YA-0 PANASONIC BADGE 1
K16 DFHG1886ZA LCD CABLE COVER CUSHION 1
K17 DFHG1887ZA KBD CABLE COVER CUSHION 1
K18 DFHG1888ZA DIMM COVER CUSHION 1
K19 DFHG1890ZA ANT CABLE CUSHION 1
K21 DFHR3E98ZA KB WP SHEET 1
K22 DFHR3E99ZA ANT CABLE SHEET 1
K25 DFHR3G26ZA BOTTOM TOP SPACER SHEET A 3
K26 DFHR3G27ZA BOTTOM TOP SPACER SHEET B 1
K27 DFHR6270YA DIMM STOPPER BASE 1
K28 DFHR6296ZA DIMM COVER SPACER 1
K29 S DFKE0857ZA-0 LCD CABLE COVER 1
K30 S DFKE0858YC-0 KB CABLE COVER 1
K31 S DFKE0859ZB-0 DIMM COVER 1
K32 S DFKE0873ZB-0 HINGE COVER L 1
K33 S DFKE0874ZB-0 HINGE COVER R 1
K34 DFMD2177ZA ANTENNA CABLE PLATE 1
K35 DFMX0634ZA CD EDGE SHEET 7
K36 DFMX0999ZA RJ11 CABLE FIX SHEET 6
K38 DFMY0438ZA W-LAN HEAT RUBBER 1
K40 DFHR3E83YA CABLE TAPE 2
K41 DFMD7B13ZA GPS BT ANGLE 1
K42 DFMX1260YA GPS INS SHEET A 1
K44 DFGX0457ZB-0 LCD CONER COVER L 1
K45 DFGX0458ZB-0 LCD CONER COVER R 1
K46 DFGX0459ZB-0 LCD CONER SIDE COVER L 1
K47 DFGX0460ZB-0 LCD CONER SIDE COVER R 1
K49 DFHG1881ZA LCD CABLE BUSH 1
K50 DFHG1884ZA LCD DROP HOLDER 2
K52 DFHG1942ZA REAR SCREW SHEET 1
K53 DFHR3159ZA TOP CASE SHEET 1
K54 DFHR3F07XA LCD CABLE WP SHEET 1
K56 DFHR7968ZA CDD SHEET 1
K57 S DFKE0871ZA-0 W-LAN ANT COVER L 1
K58 S DFKE0872ZA-0 W-LAN ANT COVER R 1
K59 DFMC0685ZA LCD CONDUCTIVE TAPE 2
K60 DFMC0863ZA INV SHIELD CASE 1
K61 DFMC0873ZA INV MIL SHIELD 1
K62 DFMC0874YA INV SHEILD TAPE 1
K63 DFMC0876ZA INV SHIELD CASE OUTSIDE 1
K65 DFMX1241ZB INV CASE 1
K70 DFHP7261XA KB SPACER TAPE 1
K71 DFHR3E65VA KB SPACER SHEET 1
K74 DFHR6260ZB-0 KB COVER 1
K75 DFMD7B38ZB-0 KB BACK PLATE 1
K76 DFQT0045ZA ENERGY STAR LABEL 1
K77 DFQT9A29ZA WINDOWS VISTA 1
K78 DFQT0048ZA CENTRINO CORE2DUO LABEL 1
K79 DFGB0165YA-0 TOUGH BADGE NEW 1
K80 S DFGT1260ZA RATING SHEET MK2 US 1
K81 DFGE0151ZA-0 WM COVER 30 1
K82 DFGP0201ZA-0 PALM TOP SHEET 1
K83 DFHE1037ZA DC GASKET 1
K84 DFHG1901ZA-0 TOUCH PAD SW RUBBER 1
K85 DFHG370ZA FOOT RUBBER 4
K86 DFHM0396ZA BATT CN PIN 2
 K90 DFHR3619ZA LEDX6 SPACER SHEET 1
K91 DFHR3636ZA CABLE HOLD SHEET 1
K92 DFHR3643ZA TP BOTTOM TAPE 1
K93 DFHR3E67ZA PAD WP SHEET 1
K94 DFHR3E93VA 1394 SHEET 1
K96 DFHR3F46ZA ICH SHEET 1
K97 DFHR3F49ZA CABLE TAPE 5X18 5
K99 DFHR3F87YA PAD PROTCT SHEET 1
K100 DFHR3G02ZA SERIAL COVER SPACER 1
K101 DFHR3G03ZA SERIAL WP SHEET 1
K102 DFHR3G04ZA USB COVER SPACER 1
K103 DFHR3G05ZA USB WP SHEET 1
K104 DFHR3G09ZA SERIAL INSIDE SPACER 1
K105 DFHR3G10ZA USB INSIDE SPACER 1
K106 DFHR3G25ZA TP FPC SHEET 1
K107 DFHR3G32ZA BATTRY SLIDE SHEET 1
K108 DFHR3G41ZA BATT CUSHION 1
K109 DFHR6355ZA TP SW KNOB IN 1
K110 DFHR6246ZA HDD GUIDE 1
K111 DFHR6247ZB BATT GUIDE 1
K112 DFHR6253YA-0 SERIAL COVER 1
K113 DFHR6254YA-0 USB COVER 1
K114 DFHR6255YA-0 DC-IN COVER 1
K116 DFHR6259YC-0 PALM TOP COVER 1
K117 DFHR6295ZA HDD CABLE COVER 1
K118 DFHR7953ZA LAN SHEET 2
K119 DFHR8521ZA BATT CN PIN CUSHION 2
K121 DFMD4066ZB-0 DC USB COVER PLATE 1
K122 DFMD4067ZB-0 SERIAL COVER PLATE 1
K123 DFMD4069ZA ICH PLATE 1
K124 DFMD7B00ZA BATT HDD CN ANGLE 1
K129 DFMX1006ZA CABLE SHEET 1
K130 DFMX1256ZA TP INS SHEET 1
K131 DFHG1403YA-0 COIN BATTERY CUSHION 1
K132 DFHG1467ZA LEAD SW CUSHION 1
K133 DFHP7275ZA CN TAPE L 1
K134 DFHP7276ZA CN TAPE S 1
K135 DFHR3E94ZA DMD CABLE SHEET 1
K137 DFHR3F59ZA MAIN PCB SPACER 1
K138 DFHR3G11ZA CN SHEET 1
K139 DFHR3G47ZA USB SCREW COVER 1
K140 DFHR3G48ZA USB SCREW COVER B 1
K141 DFHR6261ZA MODEM LAN CASE 1
K142 DFHR6272ZA MP GUIDE 1
K143 S DFKE0895YA MAIN CHASSIS 1
K144 DFMC0875ZA MAIN CHASSIS SHIELD 2
K146 DFMD7B22ZA CN PLATE 1
K148 DFMX0635ZB FFC CN STOPPER 3
K149 DFMX0702ZA FFC CN STOPPER PAD 2
K153 DFMX1280ZA EXP FPC SHEET 2
K157 DFHR3F53ZA IO PWB SHEET 1
K161 DFHP7118ZA TAPE 1
K163 DFHR3G93ZA DC-IN WP SHEET 1
K1031 DFHR3H16ZA REAR CABLE SHEET L 1
K1032 DFHR3H17ZA REAR CABLE SHEET R 1
K1122 DFNW2701ZA TOP WP WASHER 1
K1123 DFHR3741ZA FFC CN STOPPER 1
K1151 DFMC0891ZA LCD CABLE SHIELD TAPE 1
K1155 DFMY3257YA 2G DIMM HEAT PLATE 1
K1201 DFHR3K09ZA LCD CABLE GUIDE 1
K1202 DFHR3H39YA LCD CABLE CLAMP 1
K1203 D4CZY103A003 THERMISTOR 1
K1204 DFHE0915ZA EMI SHEET 10X20 1
K1205 DFHG830ZA CON SPACER 1
K1206 DFHR3F89ZA MCH SHEET 1
K1207 DFHR3K18ZA ANT CABLE WP SHEET 1
K1208 DFMY0486ZA ICH MCH HEAT RUBBER 2
K1209 DFMY0487ZA CPU HEAT RUBBER 1
K1210 DFHE1106ZA KBD GASKET 1
K1211 DFHR6354ZA-0 MIC JACK HOLDER 1
K1212 DFHG2077ZA COIN BATT CUSHION 1
K1213 DFQT0055YA COA SERIAL LAMINATE 1
K1214 DFMX0383TA INSULATION PARTS 10
N1 DRHM0002ZA SCREW 5
N2 DRHM5054XA SCREW 8
N3 DRQT2+G6FKL SCREW 2
N6 DRQT26+E4FKL SCREW 37
N7 DRSB26+10HKL SCREW 13
N8 DRSB3+8FKL SCREW 6
N9 DRYN4+J10FKL SCREW 4
N10 DXSB4+15FNMB SCREW 2
N11 DFHE5025XA SCREW 10
N12 DXQT2+F3FNL SCREW 4
N13 DRSB4+10FKL SCREW 2
N14 DFHE5058ZB SCREW 4
N15 DRHM5104ZA SCREW 3
N16 DRQT26+E5FKL SCREW 7
N17 DRQT26+E6FKL SCREW 7
N18 DRSB26+8HKL SCREW 1
N19 DRSN2+10FNL SCREW 2
N20 DXQT2+D4FNL SCREW 4
N21 DXQT2+E12FNL SCREW 2
N22 DXQT2+G4FNL SCREW 8
N29 DRQT26+E3FNL SCREW 27
N30 DXHM0057ZA SCREW 2
Replacement Parts List
Note: Important Safety Notice
Components identified by mark have special characteristics important for safety.
When replacing any of these components use only manufacturer's specified parts.

CF-30FTSAZAM
REF. NO and AREA PART NO. DESCRIPTION Q'TY

MAIN PCB
C 1, 2, 3, 5, 6, 7, 10, 11, F1J0J106A013 CAPACITOR, 6.3V, 10µF 88
12, 14, 15, 16, 18, 19,
20, 22, 23, 24, 27, 28,
29, 30, 31, 32, 33, 34,
35, 36, 37, 38, 39, 40,
44, 56, 74, 75, 78, 79,
84, 98, 100, 102, 104,
108, 115, 122, 123, 130,
132, 134, 136, 144, 146,
148, 150, 174, 177, 182,
184, 195, 199, 214, 217,
218, 219, 238, 239, 246,
269, 274, 275, 288, 350,
373, 374, 378, 394, 404,
417 442 528 610 611
C 4, 58, 86, 88, 114, 183, EEFCX0D221R CAPACITOR, 2V, 220µF 7
191
C 8, 9, 13, 17, 21, 25, 46, F1G1C104A042 CAPACITOR, 16V, 0.1µF 175
47, 48, 49, 50, 54, 57,
62, 66, 69, 70, 71, 76,
85, 87, 95, 106, 107,
112, 116, 117, 118, 125,
126, 127, 128, 131, 133,
135, 137, 139, 140, 141,
142, 145, 147, 149, 151,
170, 171, 173, 175, 176,
179, 185, 186, 187, 188,
189, 190, 192, 193, 194,
196, 197, 207, 223, 226,
232, 234, 236, 237, 240,
241, 242, 243, 245, 247,
248, 249, 250, 251, 252,
253, 254, 255, 256, 257,
258, 259, 260, 261, 262,
263, 264, 265, 267, 268,
276, 277, 278, 279, 281,
282, 289, 291, 295, 298,
302, 306, 317, 318, 319,
320, 326, 327, 328, 329,
330, 331, 332, 333, 334,
335, 336, 338, 344, 345,
346, 347, 348, 349, 392,
403, 407, 409, 410, 411,
413, 414, 415, 416, 418,
419, 420, 433, 436, 437,
438, 439, 440, 441, 445,
448, 449, 451, 452, 461,
466, 474, 478, 479, 480,
481, 482, 485, 489, 490,
496, 531, 533, 580, 581,
C 45, 504, 537, 619, 638 F1G1H222A496 CAPACITOR, 50V, 2200pF 5
C 51, 52, 53, 61, 67, 89, F1G0J474A001 CAPACITOR, 6.3V, 0.47µF 7
C 55, 72, 91, 152, 153, F1G1E103A062 CAPACITOR, 25V, 0.01µF 37
154, 155, 200, 201, 202,
203, 211, 215, 229, 280,
299, 309, 313, 340, 397,
399, 400, 405, 406, 412,
422, 423, 435, 443, 468,
519, 525, 557, 569, 574,
575, 579
C 59, 60, 103, 105, 110, F1G0J224A001 CAPACITOR, 6.3V, 0.22µF 11
113, 119, 120, 375, 383,
384
C 63, 65, 73, 77, 80, 81, F1G0J105A001 CAPACITOR, 6.3V, 1µF 16
99, 101, 172, 178, 180,
181, 212, 216, 358, 637
C 68, 82, 83, 90, 92, 94, F1J0J226A051 CAPACITOR, 6.3V, 22µF 10
111, 121, 198, 213
C 93, 205, 209, 230, 233, F1H1A1050015 CAPACITOR, 10V, 1µF 29
235, 244, 270, 271, 272,
273, 284, 301, 305, 307,
343, 352, 387, 389, 390,
393, 408, 477, 527, 603,
617, 618, 642, 644
C 156, 157, 293, 294 F1G1H150A542 CAPACITOR, 50V, 15pF 4
C 162, 163, 164, 165, 166, F1G1A104A014 CAPACITOR, 10V, 0.1µF 23
167, 168, 169, 224, 225,
353, 354, 355, 357, 359,
360, 363, 364, 371, 372,
376, 377, 395
C 204 F1G1H4R0A543 CAPACITOR, 50V, 4pF 1
C 206 F1G1H3R0A543 CAPACITOR, 50V, 3pF 1
C 208, 385, 632, 633, 634 F1H1A225A039 CAPACITOR, 10V, 2.2µF 5
C 227, 228 F1G1H2R0A543 CAPACITOR, 50V, 2pF 2
C 231, 573 F1G1C473A004 CAPACITOR, 16V, 0.047µF 2
C 266 F1L3D102A003 CAPACITOR, 2000V, 1000pF 1
C 285, 339, 341, 342, 453, F1G1H102A496 CAPACITOR, 50V, 1000pF 36
454, 455, 456, 457, 458,
459, 460, 462, 471, 473,
475, 493, 497, 498, 500,
521, 540, 542, 544, 547,
561, 564, 568, 584, 625,
626, 627, 628, 630, 635,
640
C 297, 507 F1J1E334A081 CAPACITOR, 25V, 0.33µF 2
C 300, 311, 312 F1G1H271A495 CAPACITOR, 50V, 270pF 3
C 321, 322, 323, 324, 325, F1J1E105A080 CAPACITOR, 25V, 1µF 7
587, 588
C 337, 361, 426, 427, 518, F1G1H1010005 CAPACITOR, 50V, 100pF 8
543, 559, 620
C 351, 396, 476, 483, 484, F1J0J475A009 CAPACITOR, 6.3V, 4.7µF 12
486, 505, 506, 524, 545,
566, 643
C 365, 367, 370 F1G0J334A001 CAPACITOR, 6.3V, 0.33µF 3
C 379, 381, 672 F1L0J107A016 CAPACITOR, 6.3V, 100µF 3
C 380, 421, 516, 534, 551, F1K1E1060001 CAPACITOR, 25V, 10µF 8
556, 597, 698
C 382, 530, 532 EEFCD0D101ER CAPACITOR, 2V, 100µF 3
C 386, 502, 523, 538, 548, F1G1H221A495 CAPACITOR, 50V, 220pF 6
639
C 388, 391 F1H1A474A028 CAPACITOR, 10V, 0.47µF 2
C 450, 499, 520, 529, 536, F1H1H104A748 CAPACITOR, 50V, 0.1µF 14
539, 560, 567, 595, 598,
600, 602, 604, 605
C 467, 469 F1G1A683A014 CAPACITOR, 10V, 0.068µF 2
C 487, 488 F1G1H100A544 CAPACITOR, 50V, 10pF 2
C 491, 562, 621 F1G1H470A542 CAPACITOR, 50V, 47pF 3
C 492, 629 F1G1H151A495 CAPACITOR, 50V, 150pF 2
C 494, 624 F1H1H1830001 CAPACITOR, 50V, 0.018µF 2
C 495, 631 F1G1H561A496 CAPACITOR, 50V, 560pF 2
C 501, 570, 623 F1G1H331A496 CAPACITOR, 50V, 330pF 3
C 508, 509, 510, 526, 571, F1L1E106A017 CAPACITOR, 25V, 10µF 9
596, 606, 614, 615
C 512, 513, 514, 612 EEFSX0D471XE SPCAP 4
C 515, 552 EEFCD0D151ER CAPACITOR, 2V, 150µF 2
C 517, 546, 558, 616 F1H1C224A074 CAPACITOR, 16V, 0.22µF 4
C 522, 541, 565, 641 F1G1H220A542 CAPACITOR, 50V, 22pF 4
C 549 F1G1H472A496 CAPACITOR, 50V, 4700pF 1
C 553, 554 EEFCX0J101R CAPACITOR, 6.3V, 100µF 2
C 563 F1G1H471A496 CAPACITOR, 50V, 470pF 1
C 572 EEFCD0G101ER CAPACITOR, 4V, 100µF 1
C 577 EEFCX0G151R CAPACITOR, 2V, 150µF 1
C 601 F1G1H152A496 CAPACITOR, 50V, 1500pF 1
C 607, 608, 609 DCUI1C106HDB CAPACITOR, 16V, 10µF 3
C 645, 646, 647, 648 F1J2A103A018 CAPACITOR, 100V, 0.01µF 4
C 651, 653, 654, 655, 656, F1H0J1050022 CAPACITOR, 6.3V, 1µF 23
657, 658, 659, 660, 661,
662, 663, 664, 666, 668,
669, 670, 671, 675, 676,
677, 679, 680
C 652, 674, 682, 683, 684, F1J0J4750019 CAPACITOR, 6.3V, 4.7µF 8
685, 686, 687
CF 1, 4 D4CC1103A038 THERMISTOR 2
CN 1 K1MN50AA0018 CONNECTOR 1
CN 2, 5, 6 K1MY40A00001 CONNECTOR 3
CN 3 K1KA14AA0266 CONNECTOR 1
CN 4, 29 K1MN12BA0134 CONNECTOR 2
CN 7, 8, 11, 30 K1MY40BA0220 CONNECTOR 4
CN 9 K1KY10BA0084 CONNECTOR 1
CN 10 K1MN80BA0246 CONNECTOR 1
CN 12 K1MY30AA0158 FPC CONNECTOR 1
CN 13 K1MY13BA0102 CONNECTOR 1
CN 14 K1MY16BA0097 CONNECTOR 1
CN 15 K1MY07BA0096 CONNECTOR 1
CN 16 K1KB30AA0049 CONNECTOR 1
CN 17 K1KA30BA0060 CONNECTOR 1
CN 18 K1MN08BA0134 CONNECTOR 1
CN 19 K1KA02AA0262 CONNECTOR 1
CN 20 K1KA08AA0266 CONNECTOR 1
CN 21 K1MYL0B00003 CONNECTOR 1
CN 22 K1MYL0B00004 CONNECTOR 1
CN 24 K1KY12A00004 CONNECTOR 1
CN 25 K1MN10BA0134 CONNECTOR 1
CN 26, 45 K1KA02BA0014 CONNECTOR 2
CN 28 K1FY104B0009 CONNECTOR 1
CN 31 K1KA12BA0014 CONNECTOR 1
CN 37 K1MY52BA0190 CONNECTOR 1
CN 46 K1KA02AA0299 CONNECTOR 1
CN 47 K1MY24BA0311 FPC CONNECTOR 1
D 6, 7, 19, 58, 59 MA2J72900L DIODE 5
D 8, 9, 10, 11, 12, 13, 14, B0ADCJ000041 DIODE 13
15, 16, 17, 20, 21, 22
D 24, 46, 47, 48, 49 B0JCPD000023 DIODE 5
D 25, 29, 30, 53, 60 B0JCMD000010 DIODE 5
D 26, 28, 31 B0ADCJ000025 DIODE 3
 D 33, 34, 35, 36, 37, 38, MAZ80620ML DIODE 8
62, 63
D 39, 55 MA3S132E0L DIODE 2
D 40 B2ABAM000002 DIODE 1
D 42 MA2S111-TX DIODE 1
D 43, 45, 50, 57, 64 B0JDBE000002 DIODE 5
D 44 B0JDRE000007 DIODE 1
D 51 MAZ81200ML DIODE 1
D 52 MAZ81800ML DIODE 1
D 54 B0KB00000044 DIODE 1
F 1, 4, 7 S K5H502Z00003 FUSE, 5A, 32V 3
F 2, 5, 6, 8, 12 S K5H202Z00005 FUSE, 2A, 32V 5
F3 S K5H402Z00003 FUSE, 4A, 32V 1
F 10 S K5H802300002 FUSE, 8A, 72V 1
F 11 S K5H123Y00001 FUSE, 12A, 65V 1
IC 1 C2GBD0000038 CPU 1
IC 2 C1CB00002802 CHIPSET 1
IC 3 C0JBBZ000319 PLL 1
IC 4 C1CB00002741 CHIPSET ICH8M 1
IC 5 C1CB00002732 LAN CONTROLLER 1
IC 7, 114 C0JBAZ002192 IC 2
IC 11, 12, 13 C0DBALH00003 IC 3
IC 15 C1CB00002540 IC, TEMPERATURE CENSOR IC 1
IC 20 C3EBFY000005 EEPROM 1
IC 21 C0DBEFE00003 IC 1
IC 23 C0DBZYY00265 POWER MANAGEMENT SWTICH 1
IC 24 C0DBZYY00016 IC 1
IC 25 C0ZBZ0000978 IC 1
IC 27 C3FBLY000048 FLASH MEMORY 1
IC 28 C2CBJA000003 IC, MICON 1
IC 29 C0CBCBC00181 IC 1
IC 30 C1CB00002733 AUDIO CODEC 1
IC 31, 86, 93 C0JBAS000215 IC, GATE LOGIC 3
IC 32, 58, 59, 61, 62, 68, C0JBAA000362 IC, LOGIC 13
69, 87, 103, 104, 105,
108, 109
IC 33 C0ABZA000047 IC, AMP 1
IC 34, 35, 36 C0EBE0000459 IC 3
IC 37, 78 C0EBH0000457 IC 2
IC 38, 39 C0DBZYY00026 IC, USB POWER SW 2
IC 40 C0DBAYY00194 IC, DC/DC 1
IC 41 C0DBEFH00002 IC, REGULATOR 1
IC 42 C0EBE0000333 IC 1
IC 43, 44 C0EBH0000336 IC 2
IC 45 C0DBDJH00009 IC, LINER 1
IC 47, 113 C0JBAA000381 IC, LOGIC 2
IC 50 C1CB00002723 CARDBUS CONTOLLER 1
IC 51 C1DB00001159 IC, PERIPHERAL LSI 1
IC 52 C0CBCBC00137 IC, REGULATOR 1
IC 54, 63, 64, 66 C0JBAA000345 IC, LOGIC 4
IC 55, 110 C0JBAB000624 IC 2
IC 56 C0JBAE000321 IC, LOGIC 1
IC 65, 72, 96, 101, 107 C0JBAB000621 IC, LOGIC 5
IC 67 C1CB00002790 IC, SECURITY CHIP 1
IC 70 C0ABBA000093 IC, OP AMP 1
IC 71 C0JBAD000236 IC, LOGIC 1
IC 76 C3EBDY000005 IC, EEPROM 1
IC 77 C1CB00002279 IC 1
IC 79, 80, 88 C0JBAZ002836 IC, LOGIC 3
IC 81 C0DBGYY00423 LINEAR REGULATOR 1
IC 83, 84 C0JBAZ002837 IC, LOGIC 2
IC 85 C0JBAC000367 IC, LOGIC 1
IC 89 C0DBZYY00017 IC 1
IC 92 C1CB00002497 IC, USB HUB 1
IC 94, 95 C0JBAZ002372 IC, LOGIC 2
IC 99 AN12945A-VB IC, AUDIO AMP 1
IC 100 C0JBAC000363 GATE LOGIC 1
IC 102 C0CBCAC00161 IC 1
IC 106 C0JBAZ002387 IC, LOGIC 1
IC 126 C0DBAYY00282 DC/DC CONTROLLER FOR GMCH 1
IC 127 C0JBAR000515 IC, Q-SWITCH 1
IC 128 C0DBGYY00422 LINEAR REGULATOR 1
JK 1 S K2EEYB000001 JACK 1
L 1 G1CR82M00006 COIL 1
L 5, 12, 27, 32, 34, 48, 51, J0JJC0000015 INDUCTOR 15
54, 60, 64, 68, 69, 70,
71, 77
L 8, 9 J0ZZB0000080 IDUCTOR, COMMON MODE FILTER 2
L 10, 11, 15, 16 J0JCC0000186 INDUCTOR 4
L 17 G1CR56ZA0140 INDUCTOR 1
L 18, 19, 21, 74 G1C4R7MA0240 CHOK COIL 4
L 20 G1C2R8MA0240 COIL 1
L 22 G1C100M00030 COIL 1
L 23, 53 J0JKC0000007 INDUCTOR 2
L 24 G1A160HA0032 COIL 1
L 25 G1BYYYY00009 INDUCTOR 1
L 26 J0MAB0000200 INDUCTOR 1
L 30, 47 G1C1R0Z00002 INDUCTOR 2
L 49, 50 G1C1R0MA0076 INDUCTOR 2
L 52 DDAZR100KTD INDUCTOR 1
L 59 G1C91NM00001 INDUCTOR 1
PA 6 S D4FB1R100015 PROTECTOR, 1.1A 1
Q 1, 36, 52, 53, 59, 66, 96, B1CFGD000023 TRANSISTOR 15
123, 130, 131, 133, 135,
142, 144, 153
Q 7, 10, 18, 34, 39, 94, XP0421300L TRANSISTOR 7
Q 9, 12, 20, 47, 49, 127, B1DHDC000028 TRANSISTOR 7
Q 13 2SB0766ARL TRANSISTOR 1
Q 14, 25, 75, 76, 90, 99, UNR9113J0L TRANSISTOR 11
111, 112, 134, 145, 158
Q 16, 30, 31, 32, 33, 35, UNR9213J0L TRANSISTOR 33
37, 58, 69, 81, 82, 83,
85, 86, 87, 88, 89, 101,
102, 103, 104, 107, 108,
115, 119, 121, 126, 132,
138, 139, 141, 156, 157
Q 22, 23, 24, 48, 50, 64, UNR9214J0L TRANSISTOR 18
74, 77, 78, 91, 98, 109,
110, 117, 118, 120, 146,
Q 26, 28, 38, 51 B1DDED000004 TRANSISTOR, FET 4
Q 27, 80 B1MBFDG00001 FET 2
Q 40, 41, 42, 43, 44, 45, XP0411500L TRANSISTOR 8
137, 140
Q 54, 56, 60, 61, 67, 68, B1CFRD000014 FET 11
71, 72, 84, 151, 152
Q 55, 57 B1CFRD000020 FET 2
Q 65, 73, 154 B1MBEDG00001 FET 3
Q 70, 93, 129 B1CFGD000003 TRANSISTOR 3
Q 79, 105, 106, 113, 114, B1CHRD000001 TRANSISTOR 8
122, 124, 136
Q 92, 97 B1DHDD000031 TRANSISTOR, FET 2
Q 116 XP0421400L TRANSISTOR 1
Q 125 B1MBEDA00008 TRANSISTOR 1
R 1, 2, 27, 39, 41, 43, 118, ERJ2GEJ102X RESISTOR, 1/16W, 1KΩ 13
190, 191, 262, 263, 378,
415
R3 D1H85104A024 RESISTOR ARRAY 1
R 7, 31, 66, 68, 70, 480, ERJ2RKF1001X RESISTOR, 1/16W, 1KΩ 11
481, 518, 650, 657, 673
R 8, 32 ERJ2RKF2001X RESISTOR, 1/16W, 2KΩ 2
R 9, 10, 30 ERJ2RKF1000X RESISTOR, 1/16W, 100Ω 3
R 13, 15 ERJ2RKF27R4X RESISTOR, 1/16W, 27.4Ω 2
R 14, 16, 35, 36 ERJ2RKF54R9X RESISTOR, 1/16W, 54.9Ω 4
R 18 ERJ2RKF68R0X RESISTOR, 1/16W, 68Ω 1
R 19, 23, 92, 97 ERJ2GEJ560X RESISTOR, 1/16W, 56Ω 4
R 20 ERJ2RKF2000X RESISTOR, 1/16W, 200Ω 1
R 21, 22, 33, 45, 56, 109, ERJ2GE0R00X RESISTOR, 1/16W, 0Ω 46
146, 159, 161, 163, 164,
176, 182, 203, 204, 210,
241, 280, 282, 293, 296,
297, 330, 352, 366, 369,
430, 443, 444, 455, 461,
464, 474, 478, 484, 485,
486, 504, 595, 597, 647,
668, 680, 682, 684, 690
R 24 ERJ2RKF56R0X RESISTOR, 1/16W, 56Ω 1
R 25 ERJ2GEJ240X RESISTOR, 1/16W, 24Ω 1
R 26, 48, 49, 90, 91, 103, ERJ2GEJ103X RESISTOR, 1/16W, 10KΩ 75
107, 124, 144, 181, 183,
209, 224, 251, 252, 256,
258, 269, 270, 271, 272,
273, 274, 275, 278, 279,
281, 283, 291, 292, 294,
299, 302, 303, 344, 350,
373, 379, 380, 381, 384,
389, 391, 393, 411, 419,
420, 421, 424, 428, 431,
440, 441, 442, 445, 446,
448, 453, 470, 501, 506,
513, 522, 523, 524, 543,
549, 575, 576, 577, 608,
609 649 653 672
R 28, 605, 606, 607, 615 ERJ2GEJ562X RESISTOR, 1/16W, 5.6KΩ 5
R 29 ERJ2RKF2210X RESISTOR, 1/16W, 221Ω 1
R 34, 81, 137, 177 ERJ2RKF24R9X RESISTOR, 1/16W, 24.9Ω 4
R 55, 171, 338, 339 ERJ2GEJ203X RESISTOR, 1/16W, 20KΩ 4
R 64, 65 ERJ2RKF20R0X RESISTOR, 1/16W, 20Ω 2
R 67 ERJ2RKF3920X RESISTOR, 1/16W, 392Ω 1
R 69, 626, 627 ERJ2RHD302X RESISTOR, 1/16W, 3KΩ 3
R 71, 72, 127, 242, 244, ERJ2GEJ330X RESISTOR, 1/16W, 33Ω 16
276, 286, 321, 331, 332,
351, 414, 694, 695, 696,
697
R 73, 104, 112, 113, 259, D1H81034A024 RESISTOR ARRAY 11
385, 390, 392, 417, 418,
432
R 74, 550 ERJ2RKF1301X RESISTOR, 1/16W, 1.3KΩ 2
R 75 ERJ2RKF2371X RESISTOR, 1/16W, 2370Ω 1
R 76, 77, 78 ERJ2RKF1500X RESISTOR, 1/16W, 150Ω 3
R 79, 80, 422, 423 ERJ2GEJ222X RESISTOR, 1/16W, 2.2KΩ 4
R 84, 86, 89, 156, 157, ERJ2GEJ1R0X RESISTOR, 1/16W, 1Ω 6
R 85, 88, 245, 491, 492, ERJ3GEY0R00V RESISTOR, 1/16W, 0Ω 8
624, 632, 634
R 93, 94, 96, 98, 99, 101 D1HY5608A007 RESISTOR ARRAY 6
R 95, 100, 248 D1H85604A024 RESISTOR ARRAY 3
R 105, 106, 188, 189 D1H83304A024 RESISTOR ARRAY 4
R 111, 253, 334, 498, 499, ERJ2GEJ100X RESISTOR, 1/16W, 10Ω 15
515, 516, 527, 528, 540,
541, 553, 554, 674, 675
R 126, 148 D1H84724A024 RESISTOR ARRAY 2
R 128 D1H81504A024 RESISTOR ARRAY 1
R 129, 130, 185, 186, 187, D1HY1038A007 RESISTOR ARRAY 15
257, 264, 265, 266, 267,
268, 306, 307, 308, 437
R 131 D1H81044A024 RESISTOR, 1/16W, 100KΩ 1
R 138 ERJ2RKF22R6X RESISTOR, 1/16W, 22.6Ω 1
R 149, 395, 397, 477, 660 ERJ2GEJ471X RESISTOR, 1/16W, 470Ω 5
R 151, 153 ERJ2RKF3241X RESISTOR, 1/16W, 3240Ω 2
R 152, 154 ERJ2RKF4530X RESISTOR, 1/16W, 453Ω 2
R 155, 178 ERJ2GEJ121X RESISTOR, 1/16W, 120Ω 2
R 160 ERJ6GEYJ101V RESISTOR, 1/10W, 100Ω 1
R 166, 169 ERJ2RKF3323X RESISTOR, 1/16W, 332KΩ 2
R 172 ERJ2GEJ106X RESISTOR, 1/16W, 10MΩ 1
R 173, 218, 454, 559, 560, ERJ2GEJ105X RESISTOR, 1/16W, 1MΩ 8
561, 562, 563
R 179 ERJ2GEJ331X RESISTOR, 1/16W, 330Ω 1
R 184, 206, 214, 215, 231, ERJ2GEJ472X RESISTOR, 1/16W, 4.7KΩ 13
260, 426, 427, 435, 449,
579, 580, 625
R 192, 198, 217, 246, 304, ERJ2GEJ104X RESISTOR, 1/16W, 100KΩ 39
309, 310, 315, 342, 347,
353, 357, 359, 360, 382,
404, 405, 406, 407, 408,
433, 434, 451, 456, 457,
458, 459, 497, 514, 558,
602, 610, 611, 639, 671,
685, 686, 688, 699
R 193, 200, 219, 354, 361, ERJ2GEJ474X RESISTOR, 1/16W, 470KΩ 15
362, 363, 383, 410, 425,
539, 557, 600, 601, 613
R 216, 240, 298, 300, 301, ERJ2GEJ101X RESISTOR, 1/16W, 100Ω 20
374, 375, 402, 429, 482,
564, 565, 566, 567, 568,
569, 631, 636, 676, 677
R 220 ERJ2RKF4871X RESISTOR, 1/16W, 4.87KΩ 1
R 221, 222, 254, 290, 295, ERJ2RHD103X RESISTOR, 1/16W, 10KΩ 11
327, 328, 345, 376, 377,
552
R 223, 503, 551 ERJ2RHD303X RESISTOR, 1/16W, 30KΩ 3
R 227, 228, 229, 230, 232, ERJ2RKF49R9X RESISTOR, 1/16W, 49.9Ω 8
233, 234, 235
R 236 D1H87504A024 RESISTOR ARRAY 1
R 249, 473 ERJ2RKF5101X RESISTOR, 1/16W, 5.1KΩ 2
R 284 ERJ2GEJ150X RESISTOR, 1/16W, 15Ω 1
R 287 ERJ2RKF5602X RESISTOR, 1/16W, 56KΩ 1
R 288, 289, 305 ERJ2RKF3901X RESISTOR, 1/16W, 3.9KΩ 3
R 311 ERJ2RHD3922X RESISTOR, 1/16W, 39.2KΩ 1
R 312, 387 D1H84734A024 RESISTOR ARRAY 2
R 313, 547, 670 ERJ2RHD203X RESISTOR, 1/16W, 20KΩ 3
R 317 ERJ2GEJ273X RESISTOR, 1/16W, 27KΩ 1
R 320, 346 ERJ6GEY0R00V RESISTOR, 1/10W, 0Ω 2
R 322, 335 ERJ2RKF2671X RESISTOR, 1/16W, 2.67KΩ 2
R 324, 325, 475, 533, 534 ERJ2RKF5601X RESISTOR, 1/16W, 5.6KΩ 5
R 336, 337 ERJ2GEJ333X RESISTOR, 1/16W, 33KΩ 2
R 340, 341, 367, 371, 472, ERJ2RHD104X RESISTOR, 1/16W, 100KΩ 8
545, 582, 583
R 348 ERJ2RKF1602X RESISTOR, 1/16W, 16KΩ 1
R 349 ERJ2RKF9091X CHIP RESISTOR 1
R 365 ERJ2RKD684X RESISTOR, 1/16W, 680KΩ 1
R 368, 370, 655 ERJ2RKD154X RESISTOR, 1/16W, 150KΩ 3
R 372 D1ZZ00000046 RESISTOR, 1W, 5mΩ 1
R 386, 450, 538, 588, 592, ERJ2GEJ473X RESISTOR, 1/16W, 47KΩ 8
593, 598, 599
R 388 D1H81014A024 RESISTOR ARRAY 1
R 394, 398, 438 ERJ2GEJ181X RESISTOR, 1/16W, 180Ω 3
R 396, 399, 510 ERJ2GEJ221X RESISTOR, 1/16W, 220Ω 3
R 400, 401 D1H82214A024 RESISTOR, 1/16W, 220Ω 2
R 416 D1H81004A024 RESISTOR ARRAY 1
R 452 ERJ2RKF1202X RESISTOR, 1/16W, 12KΩ 1
R 466 ERJ2RKF5103X RESISTOR, 1/16W, 510KΩ 1
R 467, 587 ERJ2RKF4702X RESISTOR, 1/16W, 47KΩ 2
R 468, 654 ERJ2RKF6801X RESISTOR, 1/16W, 6.80KΩ 2
R 469 ERJ2GEJ393X RESISTOR, 1/16W, 39KΩ 1
R 471 ERJ2RKF1800X RESISTOR, 1/16W, 180Ω 1
R 476, 488, 489, 490 ERJ3GEYJ1R0V RESISTOR, 1/16W, 1Ω 4
R 479 ERJ2RHD222X RESISTOR, 1/16W, 2.2KΩ 1
R 487, 645 ERJ3GEYJ101V RESISTOR, 1/16W, 100Ω 2
R 493, 630 D1ZZ00000093 RESISTOR, 1W, 1mΩ 2
R 494, 495, 508, 512, 531, D1BDR033A099 RESISTOR, 1/3W, 0.033Ω 7
536, 556
R 496, 509, 511, 529, 530, D1BDR022A099 RESISTOR, 1/3W, 0.022Ω 8
532, 537, 555
R 500, 521, 542 ERJ2GEJ153X RESISTOR, 1/16W, 15KΩ 3
R 502, 517, 544, 633, 640 ERJ3GEYJ100V RESISTOR, 1/16W, 10Ω 5
R 505, 507 ERJ2RHD243X RESISTOR, 1/16W, 24KΩ 2
R 519 ERJ2RHD752X RESISTOR, 1/16W, 7.5KΩ 1
R 520, 526, 586 ERJ2RHD153X RESISTOR, 1/16W, 15KΩ 3
R 525 ERJ2RHD472X RESISTOR, 1/16W, 4.7KΩ 1
R 535 ERJ2RKF1302X RESISTOR, 1/16W, 13KΩ 1
R 546 ERJ2RHD622X RESISTOR, 1/16W, 6.2KΩ 1
R 548, 570, 637, 641, 642, ERJ2GEJ223X RESISTOR, 1/16W, 22KΩ 6
643
R 571, 572 ERJ6GEYJ122V RESISTOR, 1/10W, 1.2KΩ 2
R 573, 574 ERJ6GEYJ222V RESISTOR, 1/10W, 2.2KΩ 2
R 578, 581, 594, 596 ERJ2GEJ564X RESISTOR, 1/16W, 560KΩ 4
R 584, 585 ERJ2RKF3302X RESISTOR, 1/16W, 33KΩ 2
R 589, 590 ERJ2GEJ3R3X RESISTOR, 1/16W, 3.3Ω 2
R 603 ERJ3GEYJ562V RESISTOR, 1/16W, 5.6KΩ 1
R 604 D1BDR4700001 RESISTOR, 1/8W, 0.47Ω 1
R 612 ERJ2RKD114X RESISTOR, 1/16W, 110KΩ 1
R 614 ERJ2RHD3652X RESISTOR, 1/16W, 36.5KΩ 1
R 616 ERJ2GEJ154X RESISTOR, 1/16W, 150KΩ 1
R 617, 618, 619 D1BDR1000002 RESISTOR, 1/8W, 0.1Ω 3
R 620 RL1220SR15F RESISTOR, 1/8W, 0.15Ω 1
R 622 ERA3EKB1623V RESISTOR, 1/16W, 162KΩ 1
R 623 ERA3EEB1692V RESISTOR, 1/16W, 16.9KΩ 1
R 628, 629 D1BDR068A100 RESISTOR, 0.068Ω 2
R 635 ERJ3GEYJ2R2V RESISTOR, 1/16W, 2.2Ω 1
R 638 ERJ2GEJ303X RESISTOR, 1/16W, 30KΩ 1
R 644 D1H8R0040009 JUMPER 1
R 648 ERJ2RKF4022X RESISTOR, 1/16W, 40.2KΩ 1
 R 651, 656 ERJ2RKF6981X RESISTOR, 1/16W, 6.98KΩ 2
R 658 ERJ2RKF1691X RESISTOR, 1/16W, 1.69KΩ 1
R 659 ERJ2RKF1433X RESISTOR, 1/16W, 143KΩ 1
R 661, 662 ERJ2GEJ392X RESISTOR, 1/16W, 3,9KΩ 2
R 663, 664 ERJ2GEJ4R7X RESISTOR, 1/16W, 4.7Ω 2
T 1, 2 G5BYC0000015 TRANCE 2
X1 H0J143500058 OSCILLATOR, 14.318MHz 1
X2 H0J327200115 OSCILLATOR, 32.768KHz 1
X3 H0J250500076 XTAL 1
X5 H2D800400015 OSCILLATOR, 8MHz 1
X6 H0J245500083 XTAL 1
X7 H0J240500033 XTAL 1
ZA 1, 2, 7 K1YGZZ000060 SPACER 3
ZA 3, 4 K1YGZZ000065 SPACER 2
IO PCB
C 700, 702, 718, 738, F1G1C104A042 CAPACITOR, 16V, 0.1µF 6
739, 747
C 701 F1H1H104A748 CAPACITOR, 50V, 0.1µF 1
C 703, 704, 705, 706, F1G1H1010005 CAPACITOR, 50V, 100pF 10
707, 708, 709, 710, 741,
C 712, 715 F1G1H330A542 CAPACITOR, 50V, 33pF 2
C 736, 737 F1G1H102A496 CAPACITOR, 50V, 1000pF 2
C 740 F1H1A1050015 CAPACITOR, 10V, 1µF 1
CN 700 K1MY50BA0220 CONNECTOR 1
CN 701 K1MN40B00048 CONNECTOR 1
CN 702 K1FA209BA004 CONNECTOR 1
CN 703 K1FB115BA014 CONNECTOR 1
CN 705 K1FY180BA001 CONNECTOR 1
F 701 S K5H802300002 FUSE, 8A, 72V 1
FL 703, 704, 705 J0HAAC000059 FILTER 3
JK 700, 701 K2HC103B0197 JACK 2
L 700, 701, 702, 703, DDB5Z021G-Y INDUCTOR 8
704, 705, 706, 707
L 711, 712 J0JCC0000186 INDUCTOR 2
L 713, 714, 721, 722, 723 J0JCC0000078 INDUCTOR 5
L 715, 716, 717, 718, 719 DDB5Z021C-Y INDUCTOR 5
L 720 J0JHC0000032 INDUCTOR 1
PA 700 S D4FB1R100015 PROTECTOR, 1.1A 1
R 700, 701, 702 ERJ2RKF1500X RESISTOR, 1/16W, 150Ω 3
R 703 F1G1A104A014 CAPACITOR, 10V, 0.1µF 1
R 704 EZJP0V080KA VARISTOR 1
R 706, 719 ERJ2GEJ472X RESISTOR, 1/16W, 4.7KΩ 2
R 711, 712, 713, 714, ERJ2GE0R00X RESISTOR, 1/16W, 0Ω 6
722, 723
R 716 ERJ2GEJ101X RESISTOR, 1/16W, 100Ω 1
R 717, 718 ERJ2GEJ221X RESISTOR, 1/16W, 220Ω 2
R 720, 721 ERJ3GEY0R00V RESISTOR, 1/16W, 0Ω 2
MP PCB
CN 400, 401 K1MN40B00048 CONNECTOR 2
CN 402 K1KA62B00003 CONNECTOR 1
F 401 S K5H103300003 FUSE, 10A, 72V 1
PAD PCB
C 800, 804 F1H1A1050015 CAPACITOR, 10V, 1µF 2
C 801, 802 F1G1H681A496 CAPACITOR, 50V, 680pF 2
C 803 F1G1C104A042 CAPACITOR, 16V, 0.1µF 1
CN 800 K1MN14BA0059 CONNECTOR 1
CN 801 K1MY04BA0104 CONNECTOR 1
CN 802 K1MN10BA0059 CONNECTOR 1
 D 800 DED1SS355T17 DIODE 1
IC 800 C1DB00001417 IC, FLAT PAD CONTROLLER 1
Q 800, 801 B1GKCFJN0004 TRANSISTOR 2
R 800 ERJ2GEJ224X RESISTOR, 1/16W, 220KΩ 1
R 801, 803 ERJ2GEJ822X RESISTOR, 1/16W, 8.2KΩ 2
R 802 ERJ2GEJ273X RESISTOR, 1/16W, 27KΩ 1
R 804 ERJ2GEJ105X RESISTOR, 1/16W, 1MΩ 1
R 805, 806 ERJ2GEJ222X RESISTOR, 1/16W, 2.2KΩ 2
R 808 D1H81034A024 RESISTOR ARRAY 1
SW 800, 801 EVQPLDA15 SWITCH 2
X 800 H2D400400012 OSCILLATOR, 4MHz 1
SD PCB
C 300 F1G1A104A014 CAPACITOR, 10V, 0.1µF 1
CN 300 K1MN12BA0134 CONNECTOR 1
CN 301 K1NA09E00076 CONNECTOR 1
D 300 B3ACB0000207 LED 1
R 300 ERJ2GEJ101X RESISTOR, 1/16W, 100Ω 1
USB PCB
C 100 EEFCX0J121R CAPACITOR 1
C 101, 102 EEFCX0J121R CAPACITOR 2
CN 100 K1KA14BA0014 CONNECTOR 1
CN 101, 102, 103 K1FY104BA024 CONNECTOR, USB 3
D 100 B0KB00000044 DIODE 1
D 101, 102 B0KB00000044 DIODE 2
L 100 J0MAB0000116 INDUCTOR 1
L 101, 102 J0MAB0000116 INDUCTOR 2
L 103, 104, 105, 106, DDB5Z031J-L INDUCTOR 6
107, 108
LED PCB
LED
PC
CN 901 K1MN10AA0058 CONNECTOR 1
D 901, 902, 905, 906, 907 B3ABB0000210 DIODE 5
D 903 B3ADB0000065 DIODE 1
D 904 B3AGB0000040 DIODE 1
EXT. ANTENNA PCB
CN 1, 2 K1QZA1AE0001 CONNECTOR 2
CN 3 K1QZB1AA0023 COAXIAL CONNECTOR 1
HDD BATTERY FPC
CN 4 K1KY42B00001 CONNECTOR 1
CN 5 K1KY10B00009 CONNECTOR 1
CN 7 K1KY10BA0084 CONNECTOR 1
TOUCH PANEL CONTROLLER PCB
C 200, 201, 202, 203 F1G1E472A062 CAPACITOR, 25V, 4700pF 4
C 204, 205, 206, 207 F1G1H681A496 CAPACITOR, 50V, 680pF 4
C 208, 211, 212 F1G1C104A042 CAPACITOR, 16V, 0.1µF 3
C 209 F1G1E223A062 CAPACITOR, 25V, 0.022µF 1
C 210 F1G1H102A496 CAPACITOR, 50V, 1000pF 1
C 213 F1J0J475A009 CAPACITOR, 6.3V, 4.7µF 1
C 214 F1G0J224A001 CAPACITOR, 6.3V, 0.22µF 1
C 216 F1J0J106A013 CAPACITOR, 6.3V, 10µF 1
CN 200 K1MN04BA0071 CONNECTER 1
CN 201 K1KA06BA0014 CONNECTOR 1
IC 200 C0EBE0000460 IC 1
IC 202 C1CB00002515 IC, TOUCHPANEL CONTROLLER 1
Q 200, 201 XP0431400L TRANSISTOR 2
Q 202 UNR9113J0L TRANSISTOR 1
Q 203 UNR9213J0L TRANSISTOR 1
 R 200, 206 ERJ2GEJ473X RESISTOR, 1/16W, 47KΩ 2
R 203, 205, 207, 209, 210, ERJ2GEJ102X RESISTOR, 1/16W, 1KΩ 12
211, 212, 217, 220, 221,
222, 223
R 208 ERJ2GEJ273X RESISTOR, 1/16W, 27KΩ 1
R 213, 214, 215, 216 ERJ2GEJ822X RESISTOR, 1/16W, 8.2KΩ 4
R 218 ERJ2GEJ512X RESISTOR, 1/16W, 5.1KΩ 1
R 226 DEARA8AJ473M RESISTOR ARRAY 1
R 227, 228 ERJ2GEJ270X RESISTOR, 1/16W, 27Ω 2
R 229 ERJ2GEJ152X RESISTOR, 1/16W, 1.5KΩ 1
X 200 H2D600400005 OSCILLATOR, 6MHz 1
BT PCB
C1 F1J0J106A016 CAPACITOR, 6.3V, 10µF 1
C 2, 4, 7, 11 F1G1C104A042 CAPACITOR, 16V, 0.1µF 4
C 3, 5 F1G1H102A496 CAPACITOR, 50V, 1000pF 2
C 6, 9 F1G1E103A062 CAPACITOR, 25V, 0.01µF 2
C8 F1G1H270A542 CAPACITOR, 50V, 27pF 1
C 10 F1G1HR50A543 CAPACITOR, 50V, 0.5pF 1
CN 1 K1MN10BA0070 CONNECTOR 1
IC 1 C0JBAZ002422 IC, FET SWITCH 1
IC 2 N5HZZ0000056 BLUETOOTH MODULE 1
IC 3 C0EBE0000460 IC 1
IC 5 C0JBAC000382 IC, LOGIC 1
JK 1 K1QZA1AE0001 CONNECTOR 1
L 1, 2 J0JJC0000015 INDUCTOR 2
L4 G1C5N6ZA0029 INCUCTOR 1
L5 J0MAB0000200 INDUCTOR 1
Q1 B1GBCFNN0042 TRANSISTOR 1
Q2 B1DHDC000028 TRANSISTOR 1
R 1, 2, 3 ERJ2GEJ103X RESISTOR, 1/16W, 10KΩ 3