MATERIAL LIST FOR ONE SHORT COLUMN MK'D B-8453-R018

P906 TOTAL QTY REQUIRED : 1 No(s)

P415 P415 76 80 76
FLT10*200 FLT10*200 MARK DESCRIPTION QTY MATERIAL LENGTH WGT T. WT. (KG)

12
P905

12
P313 UB203*133*25 2 ASTM A992 2014 50.0 100.0
92
142 P408 L100*6 4 ASTM A992 290 2.7 10.8
2 ASTM A992 1103 27.0 54.1

12
707 21 147 20 P409 UB203*133*25
P414 2 ASTM A36/*** 195 0.9 1.8
SHS 50*5 P907 P410 FLT10*60
P414 100 232 8 P411 FLT10*60 2 ASTM A36/*** 195 0.9 1.8
212 P905

129
SHS 50*5 ASTM A36/***
4 ø 18 P412 FLT10*60 2 230 1.1 2.2

200
P907
98

40
P413 FLT10*60 2 ASTM A36/*** 230 1.1 2.2
P906

8 64
145 145

147
P414 SHS 50*5 1 ASTM A992 1189 8.3 8.3
844

88 72
ASTM A36/***

64
P409 1 200 2.9 2.9

200

200
P415 FLT10*200
UB203*133*25 8 180 P904 FLT10*60 4 ASTM A36/*** 187 0.9 3.5
200
P408 312 P408 P905 FLT12*200 4 ASTM A36/*** 147 2.8 11.0
L100*6 188
L100*6 P408 4 ASTM A36/*** 188 3.3 13.0
SINGLE PART DRAWING P906 PL12*188
73 L100*6 P410 76 80 76
° P408 FLT10*60 P907 FLT12*200 2 ASTM A36/*** 232 4.3 8.6
P411
° L100*6 SINGLE PART DRAWING ASTM A36/***
2 232 4.3 8.6
P408
FLT10*60 P905
FLT12*200 BS
P408
L100*6
73 P905 SINGLE PART DRAWING P910 FLT12*200
FLT12*200 BS ASTM A36/***

33°
L100*6 P916 FLT15*200 2 250 5.9 11.8
P905 P410
FLT12*200 FLT10*60 TOTAL WEIGHT FOR ONE ASSEMBLY 240.6
P410
FLT10*60 P907 BOLT LIST ONE ASSEMBLY B-8453-R018
FLT12*200 76 80 76 P411
P905 SITE/SHOP BOLT DESCRIPTION QTY/ONE QTY/ALL GRADE FINISH
FLT12*200 P409
P906
226

224
UB203*133*25 Site M 16 x 40 8 8 A325M/A563 Nuts Galvanized

10
PL12*188 BS P412
P910 FLT10*60 Site M 20 x 60 8 8 A325M/A563 Nuts Galvanized
P906 FLT12*200
PL12*188
A A P410

12
P910 P904
FLT12*200 P412 FLT10*60 BS P413

10
FLT10*60 P906 FLT10*60
PL12*188 BS P910
P904
FLT10*60 BS
232 4 ø 18 195 10 175 10
P906 P910
PL12*188 FLT12*200 P910 P411
203 203
1) SURFACE PREPARATION FOR GALVANIZATION:

40
P410
SANDBLASTING SA21/2.

10

10
88 72
200

60
195 2) GALVANIZATION: ASTM A123/A123M

60

10

10
3) WELDING WHERE NOT INDICATED SHALL BE CONTINUOUS
1743

1743
10 175 10
SINGLE PART DRAWING
76 80 74 FILLET WELD. DIMENSION "S" OF NON-DIMENSIONED FILLET
T1
WELDS SHALL AT LEAST BE EQUAL TO:
SINGLE PART DRAWING SINGLE PART DRAWING S = 0.80 * T for Fy <= 250 MPa
P904
P313
UB203*133*25 P415 S = 1.00 * T for 250 < Fy <= 350 MPa T2
P313
UB203*133*25 Where: S

10
10
P412 T = MIN (T1, T2) Fy = STEEL YIELD STRENGTH OF THE
P313 ELEMENTS TO BE CONNECTED.
UB203*133*25

10
187
200 4) THE MINIMUM FILLET WELD SIZE TO BE USED FOR
B B STRUCTURAL WELDS IS 5mm.
P916
P904
P313 P415
FLT15*200 UB203*133*25 P916 32
2200 FLT15*200 5) A MINIMUM SEAL WELD LEG SIZE OF 3mm FILLET WELDS

45
P916
FLT15*200 P412 230 SHALL BE USED.
P916

60

10

10
55
FLT15*200 6) ALL STRUCTURAL STEEL, INCLUDING PLATFORMS,

200

55
HANDRAILS , LADDERS, CAGES, STAIR TREADS, CHEQUERED

32
10 167 10

60

10

10
PLATES & GRATINGS SHALL BE HOT DIP GALVANIZED ONLY,

45
SINGLE PART DRAWING EXCEPT CRANES, LIFTING BEAMS, MONORAILS, DAVITS WHICH
10 210 10 45 55 45
ARE GALVANIZED AND PAINTED RAL 1004 SAFETY YELLOW.
55
P906 P906 FOR DETAILS REFER TO PROJECT SPECIFICATION 14.192.028”
P408 P408
P408 P408 SINGLE PART DRAWING SINGLE PART DRAWING
P412
203

203
P412
145 145

145 145

145 145

145 145

80 100 70 P408
SD-UJV
203

203
P906 P414 P413
P409

50
P409 P313 4 ø 22 DOCUMENT STATUS SIGNED DATE
P906
P413
1 - ACCEPTED AS SUBMITTED (submit certified as final)

15
A-A

50
P413 REVISE AND RESUBMIT
2 -
INCORPORATE COMMENTS, UP-REV AND RESUBMIT
P916 85 120 85

10
REJECTED - Document unacceptable, REVise and resubmit
3 -
(work can proceed where not impacted by this rejection)

250
P916 290 4 - REVIEW NOT REQUIRED
100

100
33

33

P916 10 210 10
P408 SCF - SUPPLIER CERTIFIED AS FINAL
133

133

P313 P413 ISSUE OF CERTIFIED FINAL DOCUMENT DOES NOT RELIUPES SUPPLIER OF

200
RESPONSIBILITY OR LIABILITY UNDER THE CONTRACT/PURCHASE ORDER
33

33
100

100

10

10
60
29 203 18 P313
230
85 120 85 CWP No:A10-WP5.4-020-FI-MC-101
18 203 29 P916 4 ø 22
SINGLE PART DRAWING
B-B SINGLE PART DRAWING SINGLE PART DRAWING

OB RE-ISSUED FOR REVIEW UP 30/06/23 ET 30/06/23 EA 30/06/23

61 OA RE-ISSUED FOR REVIEW UP 01/03/23 ET 01/03/23 EA 01/03/23
2014
O ISSUED FOR REVIEW UP 02/02/23 ET 02/02/23 EA 02/02/23
1189 REV DESCRIPTION DWN DATE CHKD DATE APPD DATE
P414 REVISIONS
This Document is confidential. The copyright therein is vested in Nigeria LNG Ltd, Nigeria.
203

Recipient must obtain the written authority of the said company before wholly or partially duplicating.
All rights reserved.
50

P409 61 PO No: 1423030

15 VENDOR DRAWING. No. NIGERIA LIQUEFIED NATURAL GAS
61 TGIL-AD-19589-310
P313
1103 NLNG - BONNY
SINGLE PART DRAWING DRAWN: UP PROJECT
SINGLE PART DRAWING SINGLE PART DRAWING DATE: 30/06/23 NLNG TRAIN 7
CHECKED: ET
VENDOR NAME
DATE: 30/06/23
THOMPSON & GRACE INVESTMENTS LTD.
APPROVED: EA
LOCATION DISCIPLINE UNIT No
DATE: 30/06/23
BONNY ISLAND, NIGERIA CIV 2000
APPD. LNG:
TITLE
1 No.SHORT COLUMN REQUIRED AS DRAWN MARKED B-8453-R018 DATE: PO 1423030 Thompson & Grace: ASSEMBLY DRAWING
{QRCODE} CONTRACTOR DRAWING. No.
L020-CD-B-19589 FOR STEEL STRUCTURE FOR B-8453
Tekla structures

SCALE COMPANY PROJECT No. COMPANY DRAWING No. SHEET REV

B190170NTP
CAD REF: T-14.419.589-SHT420.dwg ORIGINAL SIZE: A1 CLASSIFICATION: MOST CONFIDENTIAL CONFIDENTIAL RESTRICTED UNRESTRICTED 1:10 CONTRACTOR PROJECT No.
N88480 T-14.419.589 420 OF 468 OB