Specifications
Hydraulic Rough Terrain Crane
RTC-8022 22-ton (20 metric ton)
Not to Scale
General dimensions feet meters
Turning radius (4-wheel steer -
centerline of tires) 17' 9" 5.41
Tailswing of counterweight 11' 1" 3.38
Dimensions affected by tires
Tires 16.0 X 24 (16-PR) 17.5 X 25 (20-PR)
feet meters feet meters
A 2' 3-3/8" .70 2' 1-3/16" .64
B 5' 1/4" 1.53 4' 10-1/16" 1.47
C 15° 12°
D 25° 22°
E 6' 5-1/4" 1.96 6' 3-1/16" 1.91
F 8' 5-3/4" 2.58 8' 3-5/16" 2.53
G 10' 4-1/4" 3.16 10' 2-1/16" 3.10
H 6' 11-1/16" 2.11 6' 8-7/8" 2.05
J 10' 8-3/16" 3.26 10' 6" 3.20
K 7-1/8" .18 9-5/16" .24
L 1' 1-3/4" .35 11-9/16" .29
M 1' 9-1/2" .55 1' 7-1/8" .49
N 6' 5-7/8" 1.98 6' 5-1/8" 1.96
Litho in U.S.A 3/97 1 #5231 (supersedes #5194)
Upperstructure
Boom Cab and Controls Reservoir 63 gallon (238.46 L)
Patented Design. Base and center Environmental cab; isolated from sound capacity. Single diffuser for deaeration.
section side plates have diamond shaped with acoustical foam insulation, all tinted Filtration One 10-micron filter located
impressions for superior strength to and tempered safety glass windows. outside hydraulic reservoir. Accessible for
weight ratio and 100,000 p.s.i. (689.5 Sliding rear and right side window and easy replacement.
MPa) steel angle chords for lateral swing up roof window for maximum
stiffness. The tip section is a formed visibility and ventilation. Slide-by-door Control valves Five separate control
fabricated box section. Boom telescope opens to 2' 4" (0.71 m) width. 6-way valves allow simultaneous operation of all
sections are supported by wear shoes adjustable operators seat. Hydraulic crane functions.
both vertically and horizontally to prevent control levers (joystick style) for swing,
metal to metal contact. winches and boom hoist. Outrigger Load Hoist System
controls conveniently located on dash; Standard 1M main winch with single
Microguard 414, Rated Capacity Limiter
sight level bubble also provided in upper speed motor and automatic brake; power
"RCL" - Standard; Audio-visual warning
cab. Foot controls for boom telescope, up/down mode of operation with hoist
system with anti-two block and function
swing brake, travel brake and engine drum cable follower. Bi-directional piston-
limiters. Operating data available
throttle. type hydraulic motor, driven through a
includes boom length, boom angle, head
height, radius of load, machine configura- Cab instrumentation Cab instrumen- double planetary reduction unit for
tion, allowed load, actual load and tation Dash mounted gauges for positive operator control under all load
percent of allowed load. Presettable hydraulic oil temperature, converter conditions.
alarms for maximum and minimum boom temperature, fuel, water temperature, Optional Model 1M auxiliary winch with
angles, max. tip height, max. boom voltmeter and oil pressure. one-speed motor and automatic brake,
length, swing left/right positions. power up/power down mode of operation
Standard boom 27.12' - 70.12' (8.27 Swing with hoist drum cable follower.
m - 21.37 m) three-section full power, Bi-directional hydraulic swing motor Optional - Winch function lockout on
fully synchronized boom. mounted to a planetary reducer for 360° machines equipped with two drums.
Boom head Standard Three 10-5/ continuous smooth swing at 2.0 r.p.m.
Line pulls and speeds Maximum line
8" (0.27 m) root diameter head sheaves Swing parking brake Foot operated pull 9,000 lbs. (4,082 kg) and maximum
handle up to 6 parts of wire rope. Two manually applied/released, disc brake line speed of 282 f.p.m. (84.60 m/min) on
easily removable wire rope guards and mounted on the speed reducer. standard 10-5/8" (0.27 m) root diameter
rope dead end lugs provided on each smooth drum.
side of boom head. Swing brake Foot operated, spring
released disc brake mounted on the
Auxiliary lifting sheave Optional; speed reducer. Additional Equipment -
Single 10-5/8" (0.27 m) root diameter
sheave with removable wire rope guard, Swing lock Standard; two position Standard
mounted to boom. For use with one or travel lock operated from the operators Sound suppressed cab, fire extinguisher,
two parts of line off the optional auxiliary cab. Optional 360° swing lock. seat belt, warning horn, mirrors, wind-
winch. Does not affect erection of fly, or Counterweight Bolted to upperstruc- shield wiper and backup alarm, lifting
use of main head sheaves for multiple ture frame. lugs, audible swing alarm, and automo-
reeving. tive style wiring with sealed relays and
connectors.
Boom elevation One Link-Belt Hydraulic System
designed hydraulic cylinder with holding
valve and bronze bushings in each end. Main pump Double gear type pump. Additional Upperstructure
Hand control for controlling boom Combined pump capacity 58 gpm
elevation from -3° to + 78°. (220 lpm). Driven off rear of transmis- Equipment - Optional
sion. An optional pump disconnect with 360° swing lock, propane, diesel or
engine jogging is available. Pump hydraulic heater, electronic drum rotation
Fly operates at 3,500 p.s.i. (246 kg/cm²) indicators, 25-ton (22.68 metric ton) hook
Optional 25' (7.62 m) fixed stowable maximum system pressure. block, 5-ton (4.54 metric ton) hook ball
one piece lattice type. Swing / steering pump Single gear- and swivel, rear steer indicator, engine
Optional 25' (7.62 m) offsettable type pump, 17 gpm (64 lpm) maximum. monitoring system, tachometer, top hatch
stowable one-piece lattice type. Powered by carrier engine through a window wiper, amber rotating beacon,
straight mechanical drive. Pump operates windshield washer, 360° cab mounted
Optional 25' - 43' (7.62 m - 13.10 m) at 3,000 p.s.i. (211 kg/cm²). spotlight, cab-mounted working lights,
offsettable stowable type lattice with and boom flood light.
telescoping box section. The three pump hydraulic circuit allows
simultaneous operation of the three main
crane functions (winch, boom hoist,
swing) without any function interface.
2
Carrier
Type Tires Confined Area Lift Capacities (CALC)
Front and Rear System - Outriggers may be extended to
8' 0" (2.44 m) wide, 122" (3.10 m)
Standard 16.00 x 24 (16-PR) an intermediate position (12' 11-3/4" -
wheelbase.
3.96 m) for working in confined areas.
4 x 4 x 4 (4-wheel steer, 4-wheel drive) Optional 17.5 x 25 (20-PR) Outrigger box and beam are connected
Standard For rough terrain with limited by an extend position pin which allows
turning area. Brakes the outrigger beams to be fully extended
or limits them to partially extended length
4 x 4 x 4 (4-wheel steer, 4-wheel drive) Service Hydraulic, drum-type brakes based on the selected pin position. In
Optional Rear axle with no-spin at each wheel end. Drum diameter 17" addition, capacities are available with the
differential; for rough terrain with limited (0.43 m). Shoe width 4" (.10 m). beams in the 7' 4-3/4" (2.25 m) fully
turning area.
Parking Spring applied, hydraulic retracted position.
Frame 100,000 p.s.i. (689.5 MPa) released; cab controlled, mounted on
steel, double walled construction with front axle. Additional Equipment -
integral 100,000 p.s.i. (689.5 MPa) steel
outrigger boxes. Standard
Steering
Cab steps, 2 front and rear carrier steps,
Axles Hydraulic two wheel, four wheel and air cleaner service indicator, skid
crab steering: controlled from steering resistant finish on carrier deck, key
Front- Standard; heavy duty wheel. locking storage, battery box and engine
planetary drive/steer type. compartment, automatic front axle
Rear- Standard; heavy duty Transmission disconnect, fenders, carrier mounted
planetary drive/steer type. travel lights, automotive type wiring with
Clark three-speed two range power shift sealed relays and connectors, throttle
Rear- Optional; heavy duty no- transmission. Six speeds available lock, hour meter, and towing lugs.
spin differential, planetary forward and six speeds reverse. Engine
drive/steer type. mounted torque converter.
Additional Equipment -
Suspension Outriggers Optional
Front axle- Rigid mounted to frame. Three position (fully extended, intermedi- No-spin differential on rear axle, front and
ate and fully retracted) operation. Four rear towing shackles, 110 volt engine
Rear axle- Pin-mounted on welded block heater, ether injection package,
steel box cradle. Automatic hydraulic rear hydraulic, telescoping beam and jack
outriggers. Vertical jack cylinders dual battery system, spare tires and rims,
axle oscillation lock-out engages when rear mounted pintle hook, manual pump
upperstructure rotates past 2-1/2° of equipped with integral holding valve.
Beams extend to a maximum 18' 6-3/4" disconnect with engine jogging switch,
centerline. auxiliary steering system, and recessed
(5.66 m) centerline-to-centerline and
retract to within 8' 0" (2.44 m) overall carrier mounted winch.
width. Equipped with stowable, light-
weight 16" (0.41 m) diameter steel floats.
Controls and sight level bubble located in
upperstructure cab.
Travel speeds and gradeability
Maximum *Gradeability Maximum tractive effort Gradeability Maximum tractive effort at
Speed at at stall at 1.0 mph 1.0 mph (1.61 km/h)
Engine Tires stall (1.61 km/h)
mph km/h pounds kg pounds kg
Cummins 16.0 X 24 24.3 39.10 141% 33,462 15,178 49% 18,410 8,351
4BT 3.9 17.5 X 25 22.5 36.20 211% 36,954 16,762 56% 20,331 9,222
*Transmission lubrication must not exceed 47% grade.
3
Engine Specifications
Engine Cummins 4BT 3.9
Cylinders - cycle 4-4
Bore 4.02" (102.1 mm)
Stroke 4.72" (119.9 mm)
Displacement 239.2 cu. in. (3 920 cm³)
Maximum brake hp 110 @ 2500 rpm
Peak torque 293 ft. lbs. (397 J)
Electric system 12 volt negative ground
Fuel capacity 40 gallons (151.4 L)
Alternator 100 amps
Crankcase capacity 11.6 qts. (10.98 L)
Axle loads
Base machine with standard 27.12' G.V.W. 1 Upper facing front Upper facing rear
70.12' (8.27 m - 21.37 m) three-
section boom, 350' (106.68 m) 5/8" Front axle Rear axle Front axle Rear axle
(16 mm) wire rope, 4 x 4 x 4 carrier
with Cummins 4BT 3.9 engine, 16.0 lbs. kg lbs. kg lbs. kg lbs. kg lbs. kg
X 24.0 tires, full fuel and counterweight.
37,328 16 932 18,018 8 173 19,310 8 759 18,631 8 451 18,697 8 481
17.5 x 25.0 tires -56 -26 -28 -13 -28 -13 -28 -13 -28 -13
Hookblock at boom head 430 195 1,112 504 -682 -309 -647 -293 1,077 488
Headache ball at boom head 189 86 489 222 -300 -136 -284 -129 473 214
Auxiliary lifting sheave 114 52 306 139 -192 -87 -182 -82 296 134
25' (7.62 m) lattice fly stowed 533 242 692 314 -159 -72 -116 -52 649 294
25' (7.62 m) offsettable lattice fly stowed 975 442 1,299 589 -324 -147 -244 -111 1,219 553
25' - 43' (7.62 m-13.1 m) offsettable lattice
fly stowed 1,520 689 1,987 901 -467 -212 -342 -155 1,862 844
1 Adjust gross vehicle weight & axle loading according to component weight.
Note: All weights are ± 3%
Tire Max. Axle Load @ 20 mph (32.7 km/hr)
16.00 x 24 (16-PR) 25,000 lbs. (11 340 kg)
17.50 x 25 (20-PR) 25,000 lbs. (11 340 kg)
Link-Belt Construction Equipment Company Lexington, Kentucky
A unit of Sumitomo Construction Machinery Co., Ltd.
® Link-Belt is a registered trademark. Copyright 1997.
We are constantly improving our products and therefore reserve the right
to4change
designs and specifications.
