Quick-Start Guide
USB-C 10Gbps Docking Triple Monitor Mini Station with HDMI & VGA – DP Alt Mode Pass Through - 25cm Wrap Around Cable
Product ID
DKM31C3HVCPD
Product Diagram (Side A) Component Function
• Connect to a USB-C Port on a Host Laptop
1 Built-in USB-C Host Cable • USB 3.2 Gen 2 (10Gbps)
• Power Delivery 3.0 Specification
1
• Connect a VGA Display Device
4 3 2 2 VGA Video Port • Up to 1080p (1920x1200/1920x1080) 60Hz
(Side B) • Via DisplayPort 1.4 DP Alt Mode
• Connect an HDMI Display Device
• HDMI 2.0b HDR10
3 HDMI Video Port
• Up to 4K (4096x2160) 60Hz
• Via DisplayPort 1.4 DP Alt Mode
5 • Connect and/or charge a USB-C peripheral
• Connect a USB-C display directly, or for any other
(Side C) Display, a USB-C Video Adapter is required
USB-C Data/Charge/DP++ USB 3.2 Gen 2 (10Gbps)
4 •
Video Port
• Supports 5V/2A (10W) charging
• Display output via DisplayPort 1.4 DP Alt Mode
• USB-C Power Adapter required for charging
6 5
• Connect and/or charge USB-A peripherals
(Side D) 5 2x USB-A DataPorts
• USB 3.2 Gen 2 (10Gbps)
USB-C 100W Power • Connect a USB-C power adapter
6 Delivery Input Port • USB Power Delivery 3.0
7
• Connect a CAT 5e/CAT 6 cable to establish a
7 Gb Ethernet Port network connection
• 10/100/1000Mbps
Requirements
For the latest requirements, please visit www.StarTech.com/DKM31C3HVCPD
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: September 30, 2022 11:13 AM
Installation Installation Cont’d
Side A Ports Side B Port
1. Connect the Built-in USB-C Host Cable on the Multiport Adapter to a USB-C 5. Connect USB-A cables from your USB peripheral devices to the USB-A Data Ports
port on your host laptop. Your computer will automatically detect the device and on the Multiport Adapter, to connect the devices to your computer.
install all the required drivers.
Notes:
2. Connect a VGA cable from your VGA enabled display device to the VGA Output
One of the USB-A Data Ports is located on Side C.
•
Port on the Multiport Adapter, to add a VGA display to your workstation.
• The USB port will output whatever bus power is available, up to 4.5W.
3. Connect an HDMI cable from your HDMI enabled display device, to the
Side C Port
HDMI Output Port on the Multiport Adapter, to add an HDMI display to your
workstation. 6. Connect a USB-C power adapter (up to 100W) from an AC outlet to the USB-C
100W Power Delivery Input Port on the Multiport Adapter, to charge the laptop
4. To connect a display: If using display with USB-C input, connect a USB-C cable
that’s connected to the Built-in USB-C Host Cable.
from your display to the USB-C DP++ Video Port on the Multiport Adapter . For
other displays, connect a USB-C Video Adapter (HDMI, DisplayPort or VGA, sold
separately) from the USB-C DP++ Video Port on the Multiport Adapter to your Side D Port
display device.
7. Connect a CAT 5e/CAT 6 cable from your local area network (e.g. Router, Switch,
To connect and/or charge a USB-C peripheral device: Connect a USB-C Modem, etc.) to the Gb Ethernet Port on the Multiport Adapter, to access your
cable from your USB peripheral device to the USB-C Data/Charge Port on the network via a wired LAN connection.
Multiport Adapter.
Notes:
• A video cable may also be required to connect your display, depending upon
your USB-C video adapter.
• Your computer’s USB-C port must support DP Alt Mode in order to output
video.
• Video performance, such as resolution, refresh rate depends upon your
host computer’s video controller. Please verify the specifications of your
computer.
• A USB-C power adapter must be connected to the USB-C 100W Power
Delivery Input Port on the Multiport Adapter, in order to charge connected
peripheral devices with up to 5V/2A (10W). Regulatory Compliance
• Without a power adapter connected, the USB port will output whatever bus FCC - Part 15
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
power is available, up to 4.5W. Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third- instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered following measures:
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
property of their respective holders. • Consult the dealer or an experienced radio/TV technician for help
PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
Warranty Information (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
This product is backed by a 3-year warranty. interference that may cause undesired operation. Changes or modifications not expressly approved by StarTech.com could void
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty. the user’s authority to operate the equipment.
Limitation of Liability Industry Canada Statement
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) This Class B digital apparatus complies with Canadian ICES-003.
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. CAN ICES-3 (B)/NMB-3(B)
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
or exclusions contained in this statement may not apply to you. (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.
StarTech.com StarTech.com LLP StarTech.com Ltd. StarTech.com Ltd. FR: startech.com/fr Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
Ltd. 4490 South Hamilton Unit B, Pinnacle 15 Siriusdreef 17-27 DE: startech.com/de est autorisée aux deux conditions suivantes:
45 Artisans Cres Road Gowerton Rd, 2132 WT Hoofddorp ES: startech.com/es (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
London, Ontario Groveport, Ohio Brackmills The Netherlands NL: startech.com/nl même si le brouillage est susceptible d’en compromettre le fonctionnement.
N5V 5E9 43125 Northampton IT: startech.com/it
Canada U.S.A. NN4 7BW JP: startech.com/jp
United Kingdom
