Technical Data Sheet
Approved 1493 1,2 1493 silicone acrylic ^(ValidationDate) 1
Solvalitt Midtherm
Product description
This is a one component physically drying silicone acrylic coating. It is heat resistant up to 260 °C. Can be used
as primer, mid coat or finish coat in atmospheric environments. Suitable for properly prepared carbon steel,
galvanised steel, stainless steel and aluminium substrates.
Typical use
Protective:
Designed as a heat resistant coating. Suitable for insulated and non insulated surfaces. Recommended as finish
coat for insulated surfaces, in systems with suitable primers.
Other
Other variants available
Solvalitt Midtherm Alu
Refer to separate TDS for each variant.
Colours
According to colour card.
Due to variations in the thermal stability of pigments, slight colour changes can occur when the coating is
heated. Note that such a colour change will not affect the performance of the coating.
Product data
Property Test/Standard Description
Solids by volume ISO 3233 42 ± 2 %
Gloss level (GU 60 °) ISO 2813 matt (0-35)
Flash point ISO 3679 Method 1 27 °C
Density calculated 1.3 kg/l
Region Regulation Test Standard VOC Value
US CARB(SCM)2020 / SCAQMD rule 1113 Calculated 501 g/l
Hong Kong Air Pollution Control (VOC) Regulation Calculated 501 g/l
EU European Paint Directive 2004/42/CE Calculated 501 g/l
EU IED Industrial Emission Directive 2010/75/EU Calculated 501 g/l
Korea Korea Clean Air Conservation Act KS M ISO 11890-1 512 g/l
China GB 30981-2020 Limit of harmful GB/T 23985-2009 8.3 478 g/l
substances of industrial protective coatings
Date of issue: 26 March 2024 Page: 1/5
This Technical Data Sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Solvalitt Midtherm
The provided data is typical for factory produced products, subject to slight variation depending on colour.
Gloss description: According to Jotun Performance Coatings' definition.
Note: Heat resistant topcoats can be tinted in a range of colours. However, due to its pigmentation certain
colours will appear less gloss and colour stable than others.
Film thickness per coat
Typical recommended specification range
Dry film thickness 20 - 40 μm
Wet film thickness 50 - 100 μm
Theoretical spreading rate 21 - 10.5 m²/l
Surface preparation
Surface preparation summary table
Surface preparation
Substrate Minimum Recommended
Carbon steel Sa 2½ (ISO 8501-1) Sa 2½ (ISO 8501-1)
Stainless steel The surface shall be sweep blast- The surface shall be sweep blast-
cleaned with the nozzle angle at cleaned with the nozzle angle at
45-60° from perpendicular at reduced 45-60° from perpendicular at reduced
nozzle pressure to create a sharp and nozzle pressure to create a sharp and
angular surface profile using approved angular surface profile using approved
nonmetallic abrasive media. nonmetallic abrasive media.
Aluminium The surface shall be hand or machine Abrasive blast cleaning to achieve a
abraded with non-metallic abrasives surface profile using non-metallic
or bonded fibre machine or hand abrasive media which is suitable to
abrasive pads to impart a scratch achieve a sharp and angular surface
pattern to the surface. profile.
Galvanised steel The surface shall be clean, dry and Sweep blast-cleaning using non-
appear with a rough and dull profile. metallic abrasive leaving a clean,
rough and even pattern.
Coated surfaces Clean, dry and undamaged compatible Clean, dry and undamaged compatible
coating coating
Application
Date of issue: 26 March 2024 Page: 2/5
This Technical Data Sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Solvalitt Midtherm
Application methods
The product can be applied by
Spray: Use air spray or airless spray.
Brush: Recommended for stripe coating and small areas. Care must be taken to achieve the
specified dry film thickness.
Product mixing
Single pack
Thinner/Cleaning solvent
Thinner: Jotun Thinner No. 7 / Jotun Thinner No. 10
Guiding data for airless spray
Nozzle tip (inch/1000): 15-17
Pressure at nozzle (minimum): 100 bar/1450 psi
Drying and Curing time
Substrate temperature 5 °C 10 °C 23 °C 40 °C
Surface (touch) dry 45 min 30 min 15 min 10 min
Walk-on-dry 4h 3h 2h 1h
Dry to over coat, minimum 6h 3h 2h 1h
For maximum overcoating intervals, refer to the Application Guide (AG) for this product.
Drying and curing times are determined under controlled temperatures and relative humidity below 85 %, and
at average of the DFT range for the product.
Freshly applied Solvalitt film may have slightly reduced mechanical properties. This effect can however be
overcome by heating the paint system to 200 °C for approx. 1 hour.
Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal
tackiness.
Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,
imprints or other physical damage.
Dry to over coat, minimum: The recommended shortest time before the next coat can be applied.
Date of issue: 26 March 2024 Page: 3/5
This Technical Data Sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Solvalitt Midtherm
Heat resistance
Temperature
Continuous Peak
Dry, atmospheric 260 °C -
Product compatibility
Depending on the actual exposure of the coating system, various primers and topcoats can be used in
combination with this product. Some examples are shown below. Contact Jotun for specific system
recommendation.
Previous coat: epoxy, zinc silicate, silicone acrylic
Subsequent coat: silicone acrylic
Packaging (typical)
Volume Size of containers
(litres) (litres)
Solvalitt Midtherm 5 5
The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary
due to local regulations.
Storage
The product must be stored in accordance with national regulations. Keep the containers in a dry, shaded, cool,
well-ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed.
Handle with care.
Shelf life at 23 °C
Solvalitt Midtherm 24 month(s)
In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf
life, thereafter the paint quality is subject to re-inspection.
Caution
This product is for professional use only. The applicators and operators shall be trained, experienced and have
the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical
documentation. Applicators and operators shall use appropriate personal protection equipment when using this
product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit
the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing
the work.
Date of issue: 26 March 2024 Page: 4/5
This Technical Data Sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Solvalitt Midtherm
Health and safety
Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do
not inhale spray mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable
cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.
Colour variation
When applicable, products primarily meant for use as primers or antifoulings may have slight colour variations
from batch to batch. Such products and epoxy based products used as a finish coat may chalk when exposed to
sunlight and weathering.
Colour and gloss retention on topcoats/finish coats may vary depending on type of colour, exposure
environment such as temperature, UV intensity etc., application quality and generic type of paint. Contact your
local Jotun office for further information.
Disclaimer
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are often
used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product
itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves
the right to change the given data without further notice.
Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
and specific application practices.
If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.
Date of issue: 26 March 2024 Page: 5/5
This Technical Data Sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
