AssociatedElectrics.

com
2
:: Introduction
Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and
maintaining your new vehicle. Please take a moment to read through the manual and familiarize yourself with the steps.
We are continually changing and improving our designs; therefore, actual parts may appear slightly different than the illustrations.
New parts will be noted on supplementary sheets located in the appropriate parts bags. Check each bag for these sheets before
you start to build.

:: RC10B6.2 KIT Features

• Lightweight 7075-T6 hard anodized and +3mm increased length
• New symmetric rear arm with improved geometry and stiffness can be flipped to allow a “split” for rear shock mounting position
• Longer rear arm (75mm) improves stability and jump landing
• Outer rear hinge pin captured with bolt head and lock nut for increased durability
• Updated left side rail with motor fan mount (fan not included)
• New rear hub assembly with modular vertical ball stud camber link mount and axle height adjustment
• New front wing mount and front wing included
• Bolt-on +1 steering arms for improved steering response
• 69mm CVA bones for reduced bone plunge and minimized friction at drive pin
• New body design with lower center of mass
• Clear body and wing included
• Steel electronics and under servo plates for improved balance and lower overall center of mass
• 5mm aluminum clamping wheel hexes
• Fluid filled gear differential
• 3-gear Lay Down Stealth® transmission for lower and forward CG
• Differential height adjustment with 0, 1, 2, & 3mm insert included
• 7075-T6 aluminum arm mounts with optimized roll center positions and inserts for tuning anti-squat, and toe adjustments
• Heavy-duty V2 routed graphite front shock tower w/tower guard
• Heavy-duty V2 routed graphite rear tower, STANDARD
• V2 12mm “Big Bore” threaded aluminum shock with x-rings

:: Additional
Your new B6.2 Team Kit comes unassembled • Cyanoacrylate glue (CA)(#1597)
and requires the following items for completion • Thread locking compound (#1596)
(refer to catalog section for suggestions): • Tires and Inserts, Fronts and Rears
• R/C two channel surface frequency radio system • Wheels w/12mm Hex
• AA-size batteries for transmitter (#302 alkaline) Front Wheels#9690, #9691
• Electronic Speed Control, ESC Rear Wheels #9695, #9696
(#27002, 27004, 27005, 27006, 27033)
• Steering servo (#27112, 27113, 27114, 27115, 27116)
• R/C electric motor
• Pinion gear (48P), size determined by type/wind of motor
• Battery charger (a peak detection charger, or LiPo compatible charger)
• 2 cell LiPo battery pack (#27318, 27335, 27336, 27337, 27338)
• Polycarbonate specific spray paint

:: Other Helpful Items

• Silicone Shock Fluid (Refer to catalog for complete listings)
• Body Scissors (AE Part #1737) • FT Body Reamer (#1499) • Shock Pliers (#1675)
• FT Hex/Nut Wrenches (AE Part #1519, 1650) • FT Ballcup Wrench (#1579) • FT Universal Tire Balancer (#1498)
• Green Slime shock lube (AE Part #1105) • FT Dual Turnbuckle Wrench (#1114) • Calipers or a Precision Ruler
• Soldering Iron • Hobby Knife • Wire Cutters
• Needle Nose Pliers

Associated Electrics, Inc. Customer Service

21062 Bake Parkway. Tel: 949.544.7500
Lake Forest, CA 92630 Fax: 949.544.7501
http://www.RC10.com · http://twitter.com/Team_Associated · http://www.instagram.com/teamassociatedrc/ · http://www.facebook.com/TeamAssociated/
3
:: Hardware - 1:1 Scale View
Button Head (bhcs) Flat Head (fhcs) Ball Bearings

2x4mm (31510) 2x3mm (91749) 3x7x3mm (91475)

Aluminum (8545)
2.5x8mm (31448)
2.5x6mm (31520) 5x8x2.5mm (31400)
3x8mm (25201)
2.5x8mm (31521) Aluminum (8553)
Titanium (91592) 5x10x4mm (91560)
2.5x10mm (31522)
3x10mm (25202)
3x4mm (91158) Aluminum (8555)
Titanium (91593) 6x13x5 (91562)
3x5mm (31530)
3x12mm (25203)
3x6mm (31531) Aluminum (8556)
Titanium (91580) Titanium (91594)
10x15x4 (91563)
3x14mm (89208)
3x8mm (31532) Aluminum (8567)
Aluminum (8552) Titanium (91595)
Titanium (91581) Ballstuds
3x16mm (25204)
3x10mm (25211) Titanium (91596)
Aluminum (8554) Silver 5mm long (31283)
Titanium (91582) 3x18mm (89209)
Titanium (91597)
3x12mm (89202) Silver 8mm long (31284)
Titanium (91583) Set Screws
3x14mm (25187) HD 6mm (91047)
3x2.5mm (31500) Ti Nitride HD 6mm (91118)
Titanium (91584)
Ti HD 6mm (91751)
3x3mm (25225)
3x16mm (89203)
Titanium (91585) HD 8mm (91048)
3x10mm (4671) Ti HD 8mm (91752)
3x18mm (2308)
Shims and Washers
3x20mm (25188) HD 10mm (91049)
Titanium (91587) 5.5x0.5mm (31381) Ti HD 10mm (91753)

3x22mm (25189) 5.5x1.0mm (31382)

Titanium (91588) Nuts (lock/plain)
5.5x2.0mm (31383)
3x24mm (89204) M3 Plain Nut (91477)
Titanium (91589) 2.6x6mm Washer (89278) M3 Alum. Locknut, Blue (31550)
M3 Locknut, Black (25215
3x30mm (91478)
3x8mm Washer (89218) M3 Locknut w/Flange (25612)
FT 3mm Locknuts, Blue(25392)
Diff Balls
5/64 Diff Thrust Balls (6574) Socket Head (shcs) M4 Nuts:
Serrated Steel (Silver)(91826)
3/32 Carbide Diff Balls (6581) Flanged (Black) (91148)
1.6 x 5mm (91611)
3/32 Ceramic Diff Balls (6584) FT Alum. Locknut (Blue) (25391)
Serrated Steel (Black) (91738)

Notes:
4
:: Table of Contents

1................... Cover 13 - 14........Bag 7

2................... Introduction 14 - 15........Bag 8

3...................1:1 Hardware “Fold Out” 15 - 17........ Bag 9

4................... Table of Contents 17 - 19........Bag 10

5....................Bag 1 20 - 22....... Tuning Tips

6 - 8..............Bag 2 23 - 31....... Catalog

8 - 9..............Bag 3 31................ Contact Info

9 - 10...........Bag 4 32................ Setup Sheet “Kit Setup”

10 - 11.........Bag 5 33................ Setup Sheet “Blank”

11 - 13........Bag 6 34................ Back Cover

:: Notes

This symbol indicates a special

! note or instruction in the manual.

There is a 1:1 hardware foldout page in the
front of the manual. To check the size of a part,
line up your hardware with the correct drawing
until you find the exact size. Each part in the
This symbol indicates a Racers Tip. foldout has a number assigned to it for ordering
replacement parts.

Associated Electrics, Inc. Customer Service

21062 Bake Parkway. Tel: 949.544.7500
Lake Forest, CA 92630 Fax: 949.544.7501
http://www.RC10.com · http://twitter.com/Team_Associated · http://www.instagram.com/teamassociatedrc/ · http://www.facebook.com/TeamAssociated/
9/20
5
:: Bag 1 - Step 1
Front 91475 x4

! TOP

91667
3x7x3
Ball Bearing
Note orientation
of steering rack. Steering
91475 x4 Bellcrank
3x7x3 (Right)
Ball Bearing

91667
Steering
Rack

91048 x2 31382 x2
Heavy-duty FT Ballstud 91667
Ballstud, Washer, Steering
8mm Aluminum Bellcrank
(1mm) (Left)

:: Bag 1 - Step 2
25188 x2 31283
91049 x2
!
M3 x 20mm 5mm Ball
BHCS Stud, Long Heavy-duty
The steering Ballstud,
bellcrank brace 10mm
has offsets on one 91667
side. They should be Steering
installed towards Bellcrank
the bearings.
Brace
31382 x2
FT Ballstud
Washer,
Aluminum
91766
89202 x2 (1mm)
Front
M3 x 12mm Ball Stud
BHCS

!
Mount
Do not overtighten steering bolts. Make sure
there is free movement in the steering rack.

:: Bag 1 - Step 3

!
Do not overtighten
#25225 - M3 x 3mm set screw. 31520 x2
You could bend the bar!
M2.5 x 6mm
25225 BHCS
M3 x 3mm
Set Screw

91822 91821
Anti-Roll Bar, Anti-Roll
Blue (1.0mm) Bar Collar
 6
:: Bag 2 - Step 1

!
91850
91656 Chassis,
Bulkhead B6.2
There are two bulkhead settings
(25 °, 30 °). 25 ° is the standard used.
The arrow should point
forward for the desired setting.

25

>
30

>
25204 x2
M3 x 16mm
FHCS

:: Bag 2 - Step 2
91748 91652
91747 B6 FT Steel 91734
Side Rails Battery
B6 FT Steel Chassis Weight, (L & R) Foam, B6
Chassis Weight, 36g
24g

!
#91734 - Side Rail Foams
Have two thickness
options to accomodate
any battery size.

91749 x6 25202 x4 25201 x5

M2 x 3mm M3 x 10mm M3 x 8mm
FHCS FHCS FHCS

:: Bag 2 - Step 3
91820 x2 31382 Servo not
Steering FT Ballstud included!
Link, B6.1 Washer, aluminum
(1mm)

31284
4671 8mm Ball
M3x10mm Stud, Long
Set Screw

! 31532 91728
Tighten the M3 x 8mm 91728 Servo Horn
steering link ball BHCS Servo Ring
cups all the way
until snug. Horn
 7
:: Bag 2 - Step 4
91719 x2
Servo
Mount

!
Align the servo
horn 90 degrees
91728 x2
Servo
Spacers

89218 x4
31532 x4
M3 x 8mm
M3 x 8mm
Washer !
#91728 - Servo Spacers
BHCS are not required for all servos.

:: Bag 2 - Step 5
91766 25187 x2
25211 x2 Top Plate,
M3 x 10mm M3 x 14mm
B6 BHCS
BHCS

:: Bag 2 - Step 6
The front hinge pin
brace has a sharp 25225
25211 x2 M3 x 3mm
M3 x 10mm
! edged side, and a
rounded edge side. Set Screw
BHCS Mount the sharp
edge side towards
the bulkhead.

91821
Anti-Roll
91657 Bar Pivot
Front Hinge 91820
Pin Brace, Front Anti-
bar flush
with pivot
B6 Roll Bar Link
91673 x2 31510
Front Arms, M2 x 4mm
Gull-Wing, B6 BHCS
 8
:: Bag 2 - Step 7

91685
Front
Bumper

91670 x2 25225 x2 25204 x2

Front Hinge Pin M3 x 3mm M3 x 16mm
(Inner, 3x34mm) Set Screw FHCS

:: Bag 2 - Step 8
#91865 - Front Wing Mount is used as a tuning option to
Use the outer most hole on increase front end stabillity by adding a front wing (included).
! the shock tower for kit setup
! If you do not use #91865, use #25202
M3x10mm FHCS instead of #89208 M3x14mm FHCS.

91771 91768 91815 x2

Front Shock Front Shock Shock
Tower Cover, Tower, Bushing,
Gull-Wing Gull-Wing 10mm

25188 x2
M3 x 20mm 91865 89208 x2 25202 x2
BHCS Wing Mount, M3 x 14mm M3 x 10mm
Front FHCS FHCS

:: Bag 3 - Step 1
31531 #1596
lock
M3 x 6mm thread 91776 91047
BHCS Steering Heavy-duty
Block Ballstud,
(4mm) 6mm
91560 x2
5 x 10 x 4
Bearing 91680
Steering
Block Arm,
4L ! +1mm
There are two sets of steering
blocks included with your kit, a 3mm
and a 4mm. The 4mm steering 25215
blocks are used for the kit setup. 91682 M3 Locknut,
Front Axle black
Build 2 (1 left, 1 right)
 9
:: Bag 3 - Step 2
91049 91776 25215
31532 x2
M3 x 8mm
Heavy-duty
Ballstud,
Caster
Block
M3 Locknut,
black !
There are three caster
BHCS 10mm
block inserts included
(0°, +/- 2.5 °, +/- 5 °).
+5 ° is the standard
insert used.
Tab up = positive caster
Tab down = negative caster

You can install an

optional #31520 screw
to use as a steering
stop setting.
Total Caster Block Insert
You can install an Caster 0 2.5 up 2.5 down 5 up 5 down
optional #4670 set 91776

Orientation
Bulkhead
25° 25° 27.5° 22.5° 30° 20°
screw to better hold Caster
the caster block inserts Block Insert
and hinge pin. 30° 30° 32.5° 27.5° 35° 25°
Build 2 (1 left, 1 right) (+5°)

:: Bag 3 - Step 3
25187 x2
M3 x 14mm 91676 x2
BHCS Caster Hat
Bushing
91776
Top: 0mm
Caster Block
Bottom: 3mm
Spacer
91670
Front Hinge Pin
(Outer, 3x26mm)
31510
M2 x 4mm
BHCS
#91670 - Hinge Pin will be
tight in the caster blocks,

Build 2 (1 left, 1 right) ! but should rotate freely

in the front arms. Build 2 (1 left, 1 right)

:: Bag 4 - Step 1
91772 In 1°
See next step for
Aluminum ! pill chart tips
Arm Mount,
C
91855 x2
Rear Arm
Sapcer
92014 x2
Arm Mount
92014 x2
Inserts
Arm Mount
(1°)
Inserts
(1°)
91855
B6.2 Rear
Arms, 75mm
31541 x2
91685 91688 91670
M3 x 6mm
Out 1° Rear Aluminum Rear Hinge Pin
FHCS
Bumper Arm Mount, D (Inner, 3.5x48mm)
10
:: Bag 4 - Step 2

The (#91772) C and (#91688) D aluminum arm

! mounts allow for a large amount of setup

combinations when using the (#92014) 0.5°
and 1° arm mount inserts.

C Plate Toe-In Anti-Squat

For a complete list of pill setup combinations, please
Out 1°
visit our website by using the link or QR code below.
1° 1°
D Plate
Kit Setup Kit Setup
In 1°
https://www.teamassociated.com/pdf/cars_and_
trucks/RC10B6/B6_B6D_Pill-Chart.pdf

:: Bag 5 - Step 1
91780
Gear Diff 91780
washer Gear Diff
5x15mm Sun Gear
91783
Gear Diff
Gear 91785
Gear Diff
Outdrive
91782 Pin
Gear Diff
O-Ring

#6588
black grease 91785 !
Gear Diff One pocket is flat for inserting the
#91785 gear diff outdrive pin.
Outdrive

:: Bag 5 - Step 2
91780 x4 91780
91783 #6588 Planet Gear Gear Diff
Gear Diff black grease
Diff Shim washer
Crosspin 3.5 x 9mm 5x15mm

91780 x4 91783
Planet Gear Diff
Gear Cover

#6588
black grease #658 91782
8
91782 x4 blac
k gr
ease Gear Diff
Gear Diff O-Ring
O-Ring
91785
3.3 x 0.6mm
#91782 3.3x0.6mm Gear Diff Gear Diff
! O-Rings are a tuning option.
Kit setup is built without O-Rings
Outdrive
 11
:: Bag 5 - Step 3

31522 x4
91780 M2.5 x 10mm
Gear Diff BHCS
Sun Gear

91785
Gear Diff
Outdrive 91782
Pin Gear Diff
id
Gasket ff
flu 3
Di 545
#

!
Fill to top of the
cross pins

:: Bag 6 - Step 1
91799 91791 31448
B6.1 Laydown B6.1 Laydown 2.5x8mm
#1596
Top Shaft Gearbox FHCS thread
lock
(right & left)
91560 x4
5 x 10 x 4, 91048 x2
Bearing Heavy-duty 31383 x4
Ballstud, 8mm Ballstud
Washers,
91716 5.5x2.0mm,
Idler Gear Blue Aluminum
39T
91775
91132 B6.1 Rear
Idler Gear Ballstud
89203 x2 Shaft, Mount,
3x16mm Aluminum Aluminum
BHCS

:: Bag 6 - Step 2
91821
Anti-Roll
Bar Pivot !
4671 Do not overtighten
#25225 - M3 x 3mm set screw.
M3 x 10mm
You could bend the bar!
Set Screw
25225
M3 x 3mm
Set Screw

91820 x2
2mm
Steering Link
Ball Cup

91823 91821
Anti-Roll Bar, Anti-Roll
Build x2 (right and left side) Gray (1.3mm) Bar Collar
12
:: Bag 6 - Step 3
Diff Height 91791
Add a drop of Diff Lube
B6.1 Laydown
(#6591 - not included) to
3 3 the teeth of the diff gear, Gearbox Top
Kit idler gear, and top shaft.
25225 x2
Setup
0

91
M3 x 3mm
5 e
#6 lub Set Screw
2 i ff
d
2
1
91563 x2
10x15x4 bar flush
1 Bearing with pivot
1
2

0 91792 x2
0 B6.1 Diff
Height Insert
3

:: Bag 6 - Step 4
89202 x2 91709
3 x 12mm 89203 x2 Lay-Down
BHCS 3 x 16mm Chassis
BHCS Brace
25225 x2
M3 x 3mm
Set Screw
91819
B6.1 Shock
! Pivot Ball
Do not over-tighten the
anti-roll bar set screws.
The anti-roll bar should
rotate freely in the 89203
assembly.
Use set screws to remove
3 x 16mm 25188
up and down play from the BHCS 3 x 20mm
anti-roll bar.
BHCS

:: Bag 6 - Step 5
91803
91811
B6.1 Slipper
B6.1 Spur
!
Hub, Inner There’s also a
Gear, 78T 72T, 48P spur
gear (#91809)
9611 x2 included for
25202 x3 stock motor use!
Slipper
3 x 10mm
Pad, V2
FHCS

91799
! B6.1 Top
#91811 spur gear
walls should point Shaft Screw
away from gear box. and Pin
91813 91805
B6.1 Gear 91795 B6.1 HTC
Guard B6.1 Laydown Slipper Hub,
Motor Plate Outer
 13
:: Bag 6 - Step 6
25612 91801
M3 Locknut, Slipper Spring 91801
Flanged Adapter, Inner Slipper Spring
Adapter, Inner

91801
Slipper
!
Set nut
Spring flush with
top shaft.

25204 x2
M3 x 16mm
FHCS 25202 x6

!
See page 20 for gear
mesh, and slipper clutch
M3 x 10mm
setting instructions! FHCS

:: Bag 6 - Step 7
25189 x2 91718 x2
M3 x 22mm Rear Wing
89218 x2
BHCS Mount
M3 x 8mm
Washer
91769
Rear Shock
Tower, B6.1 91718 x2
Rear Wing
Mount Spacer

25188 x4
91816 x2 M3 x 20mm
Shock
Bushing,
BHCS ! 89202 x4
#91718 Rear Wing Mount Spacers can be used as a M3 x 12mm
12mm tuninig option to help improve rear traction by moving the rear
wing farther back. If you do not use #91718, use #89202
BHCS
3x12mm BHCS instead of #25188 3x20mm BHCS.

:: Bag 7 - Step 1
Rear Axle Height
91047 #1596
lock
thread
Heavy-duty +3mm
31383 x3 3
0
Ballstud, 3 Kit
Ballstud Washers,
6mm Setup
5.5x2.0mm, blue
92179
B6.2 Rear 1
Hub Inserts 2 2 +2mm
92180
Rear Hub
Link Mounts #1596
lock
thread 2
1 1 +1mm
91857
B6.2 Rear
Hubs
89202 x2 3
0 0 +0mm
M3 x 12mm
Build x2 (right and left side) BHCS
14
:: Bag 7 - Step 2

91563
10 x 15 x 4
91438 8
Bearing
e
CVA 58 eas
#6 gr
k
Coupler bl
ac

91860 91859
CVA Bone, B6.2 CVA
69mm Axle, +2mm

91438 91567
CVA Pin 5 x 12 x 4
Bearing
Build x2 Build x2 (right and left side)

:: Bag 7 - Step 3
91436
CVA Wheel
Hex Pin

25215
M3 Locknut

92179 x2
91609 Rear Hub
Clamping Wheel Spacer
92188
Hex, 5mm Offset Rear Hub
! (rear)
Do not overtighten the
91611
Hinge Pin
M1.6 x 5mm Hinge Pin will be tight in
1.6 x 5mm SHCS into the
SHCS the rear hub, but should
Clamping wheel hex.
Build x2 (right and left side) ! rotate freely
in the rear arms. Build x2 (right and left side)

:: Bag 8 - Step 1
91722 91723 91722
Ball Cup Turnbuckle Ball Cup
3x48mm

Steering Turnbuckle
Racers Tip:
27.60mm
Orient the notch
Use black grease
to the left throughout the

!
(#6588) on the
car. It indicates which end
threads of the
has the left hand threads!
turnbuckles for
easier ball cup
installation! Build x2 (right and left side)
 15
:: Bag 8 - Step 2
91722 91723 91722
Ball Cup Turnbuckle Ball Cup
3x48mm

Front Camber Turnbuckle

26.90mm
Racers Tip:
Orient the notch
to the left throughout the Use black grease

! car. It indicates which end

has the left hand threads!
(#6588) on the
threads of the
turnbuckles for
easier ball cup
installation! Build x2 (right and left side)

:: Bag 8 - Step 3
Orient the notch
to the left throughout the 91722 91723 91722

! car. It indicates which end

has the left hand threads!
Ball Cup Turnbuckle
3x48mm
Ball Cup

Rear Camber Turnbuckle

28.70mm
Racers Tip:

Use black grease

(#6588) on the
threads of the
turnbuckles for
easier ball cup
installation! Build x2 (right and left side)

:: Bag 9 - Step 1
91480 91491
91626 31510
12x23mm V2 12mm
!
FT 12mm V2 M2 x 4mm
Shock Piston,
2x1.6 flat
BHCS
Mount the shock
Shock Bodies
(front)
Shock Cap
O-Ring !
Lightly rub shock oil
(front) 89278 pistons with the
91481 on the o-ring before
number facing up!
2.5mm 12x27.5mm
installation!

91629 Washer V2 Shock

FT 12mm V2 Bodies (rear) 31327
Shock Piston, 91615 VCS3 Shock
V2 3 x 21 91493 x2 Bottom Cap
2x1.8 flat
Shock Shaft X-Ring O-Ring
(rear)
TiN (front) #11 Racers Tip:
91495 gre
en 5
0
Racers Tip: V2 Shock slim
e Coating the o-rings
91619 Use a marker over Spacer with green slime
V2 3 x 27.5 (#1105) helps seal
the numbers on the 91495 x2 31327 & reduce o-ring
Shock Shaft pistons to make
V2 Shock VCS3 Shock
them easily visible! swell! Green slime
TiN (rear) Hat Bushing Bottom Cap not included in kit!
16
:: Bag 9 - Step 2
There is a short and
long shock eyelet.
! Front and rear
shocks use the
long eyelet.

10
5
e 4187
#1 slim
g r e e n Nylon Spacer,
(.030)
Front:
0 spacers
Short / Long
Rear:
1 spacers

91820
Shock Eyelet
Front Shocks - Short
91819
Rear Shocks - Long
Shock
Pivot Ball

:: Bag 9 - Step 3
91814
ui
d 12mm Shock Bleeding Steps:
oc
kf
l
id 91492
Sh kf
lu
Shock Cap 1. Before assembly, get each bleed
Sh
oc M2 x 4mm
screw and thread it 1-2 turns into
Front Shock: 30 wt the shock cap, then remove the BHCS
#5422 screw. This will make it easier when
you are bleeding your shocks.
Rear Shock: 30 wt 2. Pull shock shaft down.
#5422 3. Fill shock body 3/4 full with silicone Stroke
shock fluid.
4. Slowly move the shock shaft up and
down to remove air from under the
piston.
5.
6.
Wait for bubbles to come to surface.
Fill shock body to top with silicone
Stroke
shock fluid. Front: 24mm
7. Place a drop of oil in the cap and on
cap threads. Rear: 28mm
8. Install cap (without bleed screw) and
tighten completely.
9. Slowly compress shaft all the way to
bleed excess silicone shock fluid out
the hole in the cap (use rag around
shock to catch excess fluid).
10. Install M2x4mm button head
screw until snug while shaft is fully
Steps 2-3 Steps 4-5 Steps 6-7 Step 8 compressed. Steps 9-10

:: Bag 9 - Step 4
#91814 12mm Shock Spring Cups
91304 x4 0mm 5mm 9mm
12mm
Threaded
Racers Tip:
Collar
O-ring Use your finger to rub Front:
shock oil on the o-ring for 4.20mm
smoother adjustment! Rear:
8.70mm 91814
91835
12mm shock
12mm Front
spring cup
Spring, RED
(Front - 5mm
(4.60lb)
Rear - 0mm)
91304 x4 91840
12mm 12mm Rear
Threaded Spring, BLUE
Collar (2.21lb) Build x2 front and x2 rear shocks
 17
:: Bag 9 - Step 5

!
Use outside
25612
M3 Locknut
w/Flange
hole in
front arm!

!
Make sure the
flange on the
shock pivot ball is
towards the rear
arm.
25188 25187
M3 x 20mm 25612
M3 Locknut M3 x 14mm
BHCS BHCS
w/Flange
Build x2 (right and left side) Build x2 (right and left side)

:: Bag 10 - Step 1
Pinion / Setscrew 91867 89203
not included! Motor not included!
Fan M3 x 16mm
Mount BHCS

!
See page 21 for
Fan not included!
!
gear mesh setting Use cap mount if
instructions! not installing a fan.

31532 x2 89218 x2 25202

M3 x 8mm 3 x 8mm M3 x 10mm
BHCS Washer FHCS

:: Bag 10 - Step 2
Receiver not ESC not 25225
included! included!
M3 x 3mm
91730 x2
Set Screw
Battery Strap
Shoulder
6338
Antenna
Screw !
Make sure the
6727 Tube & Cap battery strap
Servo shoulder screw is
flush with the top of
Tape your battery pack!

!
Antenna can be mounted
F R

on the right or left side of

the chassis.
18
:: Bag 10 - Step 3
89218 x2 Battery
not included!
3 x 8mm 31531 x2
91731 Washer M3 x 6mm
Battery BHCS
Strap, B6

Front

1
2
3
4
5
91731 x2
B6 Battery
Strap Nut

:: Bag 10 - Step 4
91863
91729 x2 B6.2 Body,
Thumb clear
Screw, B6
31530 x2
M3 x 5mm
BHCS

91866
B6.2 Wing,
front

:: Bag 10 - Step 5
25202 x2 91718 x2
M3 x 10mm Wing
FHCS Button Wing Mount

91741
6° - Mount under wing - KIT
Wing,
B6

91718 3° - Mount on top of wing

Wing
Mount

0° - Mount under wing

Front of Vehicle
 19
:: Bag 10 - Step 6
Body Trimming / Mounting: Body Trimming for Length:
There are 2 body trimming options depending There are 2 body trimming options depending
on what transmission you choose to run. on what transmission you choose to run.

• Cut Line A is for laydown/layback transmissions. • Cut the body on the top/rear, long for the B6.2,
• Cut line B is for 4 gear transmission. shorter for the B6.2D

B6.2

Cut Line A

Cut Line B B6.2D

:: Bag 10 - Step 7

Wheels / Tires and

Inserts are
not included!

!
97 97
#15 ue #15 ue
gl gl
ca ca

Carefully apply ca glue

(tire adhesive) to the tire
Wheels / Tires and bead on the side. Do one
Inserts are side at a time, allowing it
not included! to dry before gluing the
other side!
CA glue not included!
Build x2 Build x2

:: Bag 10 - Step 8

91826
M4 Steel
91826 Serrated
M4 Steel Nut, with
Serrated Flange -
Nut, with Silver
Flange -
Silver

Build 2 (1 left, 1 right) Build 2 (1 left, 1 right)

20
:: Tuning Tips
Painting:
Your Kit comes with a clear polycarbonate body. You will need to prep the body before you can paint it.
Wash the INSIDE thoroughly with warm water and liquid detergent (do not use any detergents with scents or added
hand lotion ingredients!). Dry the body using a clean, soft, lint-free cloth. Use the supplied window masks to cover the
windows from the INSIDE of the body (RC cars get painted on the inside). Using high quality masking tape, apply tape
to the inside of the body to create a design. Spray (use either rattle can or airbrush) the paint on the inside of the body
(preferably dark colors first, lighter colors last). NOTE: ONLY use paint that is recommended for (polycarbonate)
plastics. If you do not, you can destroy the body! After the paint has completely dried (usually after 24 hours), cut the
body along the trim lines. Make sure to drill or use a body reamer to make the holes for the antenna if needed! Use hook
and loop tape to secure the body to the side rails of the vehicle.

Tips for Beginners:

Before making any changes to the standard setup, make sure you can get around the track without crashing. Changes
to your vehicle will not be beneficial if you can’t stay on the track. Your goal is consistent laps. Once you can get around
the track consistently, start tuning your vehicle. Make only ONE adjustment at a time, testing it before making another
change. If the result of your adjustment is a faster lap, mark the change on the included setup sheet (make adddtional
copies of the sheet before writing on it). If your adjustment results in a slower lap, revert back to the previous setup and
try another change. When you are satisfied with your vehicle, fill in the setup sheet thoroughly and file it away. Use this
as a guide for future track days or conditions. Periodically check all moving suspension parts. Suspension components
must be kept clean and move freely without binding to prevent poor and/or inconsistent handling.

Rear Arm Mount Pill Insert Setup:

!
For additional setup tips, please
visit our website by using the link
or QR code below.

https://www.teamassociated.
com/pdf/cars_and_trucks/
RC10B6/B6_B6D_Pill-Chart.pdf
 21
:: Tuning Tips (cont.)
Motor Gearing:
Proper motor gearing will result in maximum performance and run time while reducing the chance of overheating and
premature motor failure. The gear ratio chart lists recommended starting gear ratios for the most widely used
motor types. Gear ratios will vary depending upon motor brand, wind, and electronic speed control. Consult your
motor and electronic speed control manufacturers for more information.
Team Associated is not responsible for motor damage due to improper gearing.

B6 Gear Ratio Chart (Internal Gear Ratio 2.60:1)

Motor Pinion Spur Final Drive Ratio
21.5 Reedy S-Plus Brushless 33 72 5.67:1
17.5 Reedy S-Plus Brushless 29 72 6.45:1
13.5 Reedy S-Plus Brushless 27 75 7.22:1
10.5 Reedy 540-M3 Brushless 24 78 8.45:1
9.5 Reedy 540-M3 Brushless 23 78 8.82:1
8.5 Reedy 540-M3 Brushless 22 78 9.22:1
7.5 Reedy 540-M3 Brushless 21 78 9.65:1
6.5 Reedy 540-M3 Brushless 20 78 10.14:1

Set The Gear Mesh:

You should be able to rock the spur gear back and forth in the teeth of the pinion gear without making the pinion gear
move. If the spur gear mesh is tight, then loosen the #31532 screws and move the motor away, then try again.
A gear mesh that is too tight or too loose will reduce power and damage the gear teeth.

Diff Height Adjustment:

The diff height adjustment is a good way to tune the car for grip level. On high grip with low ride heights, a higher diff
height will be a good option. On lower grip with higher ride heights, a lower diff height will be better.

Gear Box Type:

Selecting the correct gear box is dependent on the type of track it will be used on. The optional 4 gear stand-up gear
box is for the lowest grip conditions. This gear box moves the weight towards the rear of the car and also uses the
rotation of the motor to transfer weight to the rear while on-power. The 3 gear stand-up gear box also moves the
weight towards the rear of the car, but in this configuration, the motor’s rotation helps with on-power steering.
The lay-down gear box is used on high grip conditions when on-power steering and stability are most important.
This gear box will change directions the quickest and generate the most steering. Layback is used for most indoor clay
track conditions.

Slipper Clutch:
The assembly instructions give you a base setting for your clutch. Turn the nut on the shaft so that the end of the top
shaft is even with the outside of the nut. At the track, tighten or loosen the nut in 1/8 turn increments until you hear
a faint slipping sound for 1-2 feet on takeoffs. Another popular way to set the clutch is to hold both rear tires firmly in
place and apply short bursts of throttle. If the clutch is properly set, the front tires should lift slightly up off the surface.

Caster:
Caster describes the angle of the caster block as it leans toward the rear of the vehicle. Positive caster means the
kingpin leans rearward at the top. The kit includes three inserts to adjust caster angle at the caster block, 0°, 2.5°, and
+5°. The total caster angle is the sum of the kick-up angle and the caster block angle. Standard total caster angle for
the B6 is 30°, with 25° kick-up and +5° caster block angle.
For less entry steering and more exit steering, try 0° caster block angle.

Front Camber:
Camber describes the angle at which the tire and wheel rides when
looked at from the front. Negative camber means that the tire leans
!
inward at the top. A good starting camber setting is -1°. Positive camber,
where the top of the tire is leaning out, is not recommended. *Testing camber
Optional #1719 camber gauge can be used to more accurately set camber. with camber gauge

Rear Camber:
Camber describes the angle at which the tire and wheel rides when looked at from the back. Negative camber means
that the tire leans inward at the top. A good starting camber setting is -1°. Adding a small amount of positive camber,
where the top of the tire is leaning out, will tend to improve straight-line acceleration on loose tracks.
Optional #1719 camber gauge can be used to more accurately set camber.
22
:: Tuning Tips
Front Camber Links:
Changing the length of the camber link is considered a bigger step than
adjusting the ball end height on the tower. Shortening the camber link
(or lowering the ball end) will give the front end less roll and quicken steering !
response. Lengthening the camber link (or raising the ball end) will give the *Raise or lower the
front more roll and slower steering response. Longer camber links are ball end by adding
typically used on high grip tracks and shorter links tend to work better on or removing
medium-grip loose tracks. washers here

Rear Camber Link:

Changing the length of the camber link is considered a bigger step than adjusting the !
ball end height on the rear chassis brace. Shortening the camber link (or lowering the *Raise or lower
ball end) will give the rear end less roll and the car will tend to accelerate or “square up” the ball end by
better. Lengthening the camber link (or raising the ball end) will give the rear more roll adding or
and more cornering grip. Longer camber links are typically used on high grip tracks, removing
while shorter links tend to work better on medium grip loose tracks. washers here
The kit setting is the best compromise of cornering grip and acceleration.

Ackermann:
Ackermann is the angle difference between the front wheels when they are turned to steer the car. For minimal tire
slip, it is standard for the inside wheel to steer to a greater angle than the outside wheel. The kit allows Ackermann
adjustments by changing the washer thickness used behind the steering rack ballstuds. The kit setup uses 2mm
washers and is most common for racing conditions. If corner entry steering is too aggressive, try increasing the
Ackermann by removing shims from behind the steering rack ballstuds. Increasing the Ackermann will increase the
angle difference of the front wheels when steered, resulting in a more stable car on corner entry.

Kickup:
Kickup is the angle the front suspension arm mounts at where the front of the arm is higher than the rear.
The standard kickup angle for the B6 is 25°, and is most common. If more corner entry steering is desired, try the
included 30° front bulkhead.

Axle Height:
Axle height is used to keep roll centers similar when large ride height changes are made. As a rule of thumb, high axle
heights are used for lower ride heights (< 20mm) and low axle heights are used for higher (> 22mm) ride heights. The
idea is to keep the arms close to level at ride height.

Ride Height:
Ride height is the distance from the ground to the bottom of the chassis.
The standard front ride height setting is 19mm (Ride Height Gauge #1449). Check the front ride height by lifting up
the entire car about 8-12 inches off the bench and dropping it. After the suspension “settles” into place, measure ride
height (Ride Height Gauge #1449). Raise or lower the shock collars as necessary.

The rear ride height setting you should use most often is 19mm (Ride Height Gauge#1449). Check the rear ride height
by lifting up the entire car about 8-12 inches off the bench and drop it. After the suspension “settles” into place,
measure ride height (Ride Height Gauge #1449). Raise or lower the shock collars as necessary.

Wheelbase Adjustment:
You have three options for rear hub spacing; forward, middle, & back. The kit
!
*Spacers to the rear
setting of middle is the most neutral, and will be used most often. For improved will place hubs
handling in bumps or rhythm sections, try moving the hubs to the back position. forward, shortening
Hub forward is typically used on low grip or where there are lots of tight corners. the wheelbase

Anti-Roll Bars:
The anti-roll bar kits (also called the “swaybar”) allows you to add roll resistance to the front and /or rear end with
minimal effect on handling over bumps and jumps. It is an especially helpful tuning item on high-grip tracks.

Shock Mounting Position:

The rear shocks can be mounted on the front or rear of the rear suspension arm. Mounting the shocks on the front
of the arm reduces rear weight bias. This causes the car to turn quicker and also steer more on-power. Usually this is
used on high bite tracks in order to keep the car steering while applying throttle. Mounting the shocks on the rear of
the arm increases rear weight bias and keeps the rear end planted while making the steering radius larger.
This setting is typically easier to drive and will produce more rear traction.
 23
:: Shocks :: Ball Differential
4187 .030 Nylon Washer 12 1733 Diff Shims 8
31327 VCS3 Shock Bottom Cap and O-Ring 2 ea. 6573 Diff Thrust Washer & Bolt 2
31510 2x4mm BHCS 6 6574 Precision Diff Thrust Balls, 5/64” 6
89278 2.5mm Washer 20 6575 Locking T-Nut, Diff Thrust Bolt, & Cover 1
91304 12MM Threaded Collar and O-Ring 2 6581 3/32” Carbide Diff Balls 12
91480 12x23MM V2 Shock Bodies 2 6582 Diff Thrust Spring 1
91481 12x27.5MM V2 Shock Bodies 2 7666 Diff Drive Rings, 2.60:1 2
91491 12MM V2 Shock Rebuild Kit 1 7677 Ball Diff Rebuild Kit 1
91492 M2 x 4mm BHCS with Washer 2 31400 Bearing, 5 x 8mm 2
91493 FT Low Friction X-Rings 8 91419 Diff Gear, B5 1
91495 12 mm V2 X-Ring Rebuild Kit 1 91701 Ball Diff Outdrive, B6 1 ea.
91615 3 x 21mm Shock Shaft (V2), TiN 2 91702 Ball Diff Kit, B6 1
91619 3 x 27.5mm Shock Shaft (V2), TiN 2
91626 FT 12mm Pistons (V2), 2x1.6 mm, flat 4
91629 FT 12mm Pistons (V2), 2x1.8 mm, flat 4
91814 B6.1 Shock Caps/Spring Cups 4 ea. 91702
91819 B6.1 Shock Pivot Balls 4
91820 B6.1 Ball Ends 1

91814
6575 31400
91492
91304 6582
91491 31510
7666
91626
91629 91304
91701
89278
91480
91481 91701

91615 7666
91619 91814 6573
91495 6574
31400
6573
91493

91819 6581 6575

91493
4187
91820
31327
91419 6575
31327

:: Shock Springs :: Shock Fluid

91830 Front Shock Spring, Green 3.10lbs Pr. 5420 10 Weight Silicone Shock Fluid 2oz.
91831 Front Shock Spring, White 3.40lbs Pr. 5421 20 Weight Silicone Shock Fluid 2oz.
91832 Front Shock Spring, Gray 3.61lbs Pr. 5422 30 Weight Silicone Shock Fluid 2oz.
91833 Front Shock Spring, Blue 3.91lbs Pr. 5423 40 Weight Silicone Shock Fluid 2oz.
91834 Front Shock Spring, Yellow 4.30lbs Pr. 5424 22.5 Weight Silicone Shock Fluid 2oz.
91835 Front Shock Spring, Red 4.60lbs - KIT Pr. 5425 80 Weight Silicone Shock Fluid 2oz.
91836 Front Shock Spring, Orange 5.10lbs Pr. 5426 27.5 Weight Silicone Shock Fluid 2oz.
91837 Rear Shock Spring, Green 1.81lbs Pr. 5427 15 Weight Silicone Shock Fluid 2oz.
91838 Rear Shock Spring, White 1.91lbs Pr. 5428 25 Weight Silicone Shock Fluid 2oz.
91839 Rear Shock Spring, Gray 2.00lbs Pr. 5429 35 Weight Silicone Shock Fluid 2oz.
91840 Rear Shock Spring, Blue 2.20lbs - KIT Pr. 5430 45 Weight Silicone Shock Fluid 2oz.
91841 Rear Shock Spring, Yellow 2.30lbs Pr. 5431 55 Weight Silicone Shock Fluid 2oz.
5432 32.5 Weight Silicone Shock Fluid 2oz.
5433 37.5 Weight Silicone Shock Fluid 2oz.
5434 42.5 Weight Silicone Shock Fluid 2oz.
5435 50 Weight Silicone Shock Fluid 2oz.
5436 60 Weight Silicone Shock Fluid 2oz.
5437 70 Weight Silicone Shock Fluid 2oz.
5438 47.5 Weight Silicone Shock Fluid 2oz.
24
:: Transmission
25188 M3 x 20mm BHCS 10
25202 M3 x 10mm FHCS 10 89203
25204 M3 x 16mm FHCS 10
31383 Ballstud Washers, 5.5x2.0 mm, 10 89202 89203
blue aluminum
31448 M2.5 x 8mm FHCS 10
31532 M3 x 8mm BHCS 10 91791
89202 M3 x 12mm BHCS 10
89203 M3 x 16mm BHCS 10 31448
89218 M3 x 8mm Washers 10 89218 25202 91048
91048 Heavy-duty Ballstuds, 8 mm 10
91048
91132 4x4 FT Idler Shafts, aluminum 2 31383
91560 FT Bearings, 5x10x4 mm 4 91813
91791
91709 B6 Chassis Braces 1 ea. 31383
91716 B6 Idler Gear, 39T, laydown 2 91560
91775 B6.1 Rear Ballstud Mount 1 91775
91791 B6.1 Laydown Gearbox 1 31532 91716
91795 B6.1 Laydown Motor Plate 1 91795
91799 B6.1 Laydown Top Shaft 1 91132
91813 B6.1 Gear Cover 1
91819 B6.1 Shock Pivot Balls 4 91819 91791
91709
25188
91799
25202
91560

25202
25204
89203

:: Slipper Clutch
9611 Slipper Pad, V2 2
91799
25612 M3 Locknuts, Flanged 10
91799 B6.1 Laydown Top Shaft 1
91801 B6.1 Slipper Spring and Adaptors 1
91803 B6.1 Slipper Hub, Inner 1
91804 B6.1 Slipper Hub, Outer 1 9611
91805 B6.1 HTC Slipper Hub Outer 1
91808 B6.1 Spur Gear, 69T - 48P 1
91809 B6.1 Spur Gear, 72T - 48P 1 91803
91810 B6.1 Spur Gear, 75T - 48P 1 9611
91811 B6.1 Spur Gear, 78T - 48P - KIT 1
91812 B6.1 Spur Gear, 81T - 48P 1

91801
91811

91805

25612

:: Pinion Gears
1335 17T 48P Aluminum Pinion Gear 1 1349 31T 48P Aluminum Pinion Gear 1
1336 18T 48P Aluminum Pinion Gear 1 1350 32T 48P Aluminum Pinion Gear 1
1337 19T 48P Aluminum Pinion Gear 1 1351 33T 48P Aluminum Pinion Gear 1
25225
1338 20T 48P Aluminum Pinion Gear 1 1352 34T 48P Aluminum Pinion Gear 1
1339 21T 48P Aluminum Pinion Gear 1 1353 35T 48P Aluminum Pinion Gear 1
1340 22T 48P Aluminum Pinion Gear 1 25225 M3 x 3mm Set Screw 20
1341 23T 48P Aluminum Pinion Gear 1
1342 24T 48P Aluminum Pinion Gear 1
1343 25T 48P Aluminum Pinion Gear 1
1344 26T 48P Aluminum Pinion Gear 1
1345 27T 48P Aluminum Pinion Gear 1
1346 28T 48P Aluminum Pinion Gear 1
1347 29T 48P Aluminum Pinion Gear 1
1348 30T 48P Aluminum Pinion Gear 1
 25
:: Gear Differential
31522 M2.5 x 10mm BHCS 10 91563
91563 FT Bearings, 10x15x4 mm 4 31522
91780 B6.1 Gear Differential Rebuild 1 91792
91782 B6.1 Gear Differential Seals 1 91782
91783 B6.1 Gear Differential Case 1
91784 B6.1 Aluminum Cross Pins 2 91785 91780
91783
91785 B6.1 Gear Differential Outdrives 2
91786 B6.1 Gear Differential 1 91782
91792 B6.1 Differential Height Inserts 2 ea. 91785
91780
5450 Silicone Diff Fluid 1,000CST 1
5451 Silicone Diff Fluid 2,000CST 1 91780
5452 Silicone Diff Fluid 3,000CST 1 91780
5444 Silicone Diff Fluid 4,000CST 1
5453 Silicone Diff Fluid 5,000CST 1
5446 91782
Silicone Diff Fluid 6,000CST 1
5454 Silicone Diff Fluid 7,000CST 1
5455 Silicone Diff Fluid 10,000CST 1 91780
5466 Silicone Diff Fluid 15,000CST 1 91783
5456 Silicone Diff Fluid 20,000CST 1
5457 Silicone Diff Fluid 30,000CST 1 91785
5458 Silicone Diff Fluid 60,000CST 1 91785
5448 Silicone Diff Fluid 80,000CST 1 91783
5459 Silicone Diff Fluid 100,000CST 1 91780 91782
5461 Silicone Diff Fluid 200,000CST 1 91792
5463 Silicone Diff Fluid 500,000CST 1
5465 Silicone Diff Fluid 1,000,000CST 1 91563

:: Turnbuckles and Servo Mounts

4671 M3 x 10mm Set Screw 6 91728
25211 M3 x 10mm BHCS 20
31284 Ball Studs Long, 8mm 6
31284 91728
31382 FT Ballstud Washer, aluminum1mm 10
31532 M3 x 8mm BHCS 6
89218 M3 x 8mm Washers 10 25211
91719 Servo Mount, B6 2 91820
91722 Ball Cups, B6 12
91723 3 x 48mm Turnbuckle 2
91728 B6 Servo Horns, 15.5 mm 1 31532 89218
91820 B6.1 Ball Ends 1

31382
31532 91719
4671
91722 91723

31532
89218 89218
91820

:: Anti-Roll Bards / Battery Strap

25225 M3x3mm Set Screw 10
31531 M3 x 6mm BHCS 20 91729 31531
89218 3 x 8mm Washers 10 25225
91729 Thumb Screw, B6 2 89218 25225
91730 Battery Strap Shoulder Screw 2 91820
91731 Battery Strap, B6 1 31531
91820 B6.1 Ball Ends 1 91731
89218 4671 91821
91821 B6.1 Anti-Roll Bar Hardware 1
91821
91822 B6.1 FT Front Anti-Roll Bar Set 1 91729 91820
91823 B6.1 FT Rear Anti-Roll Bar Set 1

25225
91731
25225
91730 91731 91821

91730 91820
91821
26
:: Front Arm
25187 M3 x 14mm BHCS 10
25188 M3 x 20mm BHCS 10 25187
25215 M3 Locknut, Black 10 91048
31382 FT Ballstud Washer, aluminum1mm 10
31510 M2 x 4mm BHCS 6 91049 31532
31531 M3 x 6mm, BHCS 6 31382
31532 M3 x 8mm, BHCS 6 25215
91048 Heavy-duty Ballstud, 8mm 8
91049 Heavy-duty Ballstud, 10mm 8 91676
91776
91560 FT Bearing, 5 x 10 x 4 4
91670 Hinge Pin Set, B6 1 91776 91680
91673 Front Arm, Gull-Wing, B6 2 25215
91676 B6 Caster Hat Bushings 2 ea.
91680 B6 Steering Block Arms (+1) 2 31531
91682 Front Axle, B6 2
91776 B6.1 Caster/Steering Blocks 1 91560
25187
91826 M4 Serrated Wheel Nut, Steel (Silver) 10

91682
91776
91560

91670 91826
31510

25188
91673
31510

91670
91776

:: Rear Arm
25187 M3 x 14mm BHCS 10
25215 M3 Locknut, Black 10
31383 Ballstud Washers, 5.5x3.0x2.0mm, 10
Blue Aluminum 91860
89202 M3x12mm BHCS 10 91438
91047 Heavy-duty Ballstud, 6mm 10
91436 CVA/Wheel Hex Pin, B5 4
91438 CVA Rebuild Kit, B5 1 91047
91859
91563 FT Bearing, 10 x 15 x 4 4
91567 FT Bearing, 5 x 12 x 4 4
91609 FT Clamping Wheel Hexes, 5.0mm 2 31383
91611 M1.6 x 8mm SHCS 4 91438
91826 M4 Serrated Wheel Nut, Steel (Silver) 10
89202
91855 B6.2 Rear Arms, 75mm Pr. 91563
91857 B6.2 Rear Hubs 2
91859 B6.2 CVA Axle, +2mm 2 92180
91860 B6.2 CVA Bone, 69mm 2 91857
92179 B6.2 Rear Hub Inserts and Spacers 1 91436
92180 B74 Rear Hub Link Mount 2
92188 B74 Rear Hub Hinge Pin 2 92179 91611
91567

91609

91826
91855
92188

25187
25215 92179
 27
:: Front Shock Tower
25188 M3 x 20mm BHCS 10
25202 M3 x 10mm FHCS 10
25612 M3 Locknuts w/Flange 10
31530 M3x5mm BHCS 10
89208 M3x14mm FHCS 10
91768 B6.1 Front Shock Tower 1
91771 B6.1 Shock Tower Covers 1 91771 91768
91815 Shock Bushing, 10mm 4 25188 91815
91865 B6.2 Wing Mount, Front 1 25612

31530

25188
91815 25612
89208

25202
89208

91865 25202

:: Rear Shock Tower

25188 M3 x 20mm BHCS 10
25189 M3 x 22mm BHCS 10 25202
25202 M3 x 10mm FHCS 10
25612 M3 Locknuts w/Flange 10
89202 M3 x 12mm BHCS 10 25189 91718
89218 M3 x 8mm Washers 10
91718 Wing / Body Mount Set, B6 1
91769 B6.1 Rear Shock Tower 1 91769 89218
91816 Shock Bushing, 12mm 4 25189 91718

91816 89202 89218 91718

25612 91718
91718
89202
91816
25612 25188 91718
25188

:: Wheels
9690 Buggy Front Wheel, hex, white 2
9691 Buggy Front Wheel, hex, yellow 2
9695 Buggy Rear Wheel Hex, white 2
9696 Buggy Rear Wheel Hex, yellow 2
Not included
in Kit!

Not included
in Kit!
28
:: Front Bulkhead / Steering
25187 M3 x 14mm BHCS 10
25204 M3 x 16mm FHCS 10
25211 M3 x 10mm BHCS 10
25225 M3 x 3mm Set Screw 10
31283 Ball Studs, Long, 5mm 6
31382 Ballstud Washers, 5.5x1.0 mm, 10
blue aluminum
89202 M3 x 12mm BHCS 8 91049
91048 Heavy-duty Ballstud, 8mm 8 91678
91049 Heavy-duty Ballstud, 10mm 8 31382 91678
91475 3x7x3 Ball Bearing 1 91049
91656 Bulkhead, B6 1
91657 B6 Front Hinge Pin Brace 1
91667 Steering Assembly, B6 1 31382 91667
91766
91678 M3 x 20mm BHCS, Shouldered 10
91685 Bumpers, B6 1 ea. 91475
91766 B6.1 Top Plate, Ballstud Mount 1 ea. 31283
91656 91667

91475 91667
91657
25211 91475
25204 91475
25211
25225
25187 91048 31382 91475
25204
25225 91048
91667
91766 91475
31382
25187
91685 91475

25204 89202
25204 89202

:: Chassis
6338 Antenna Tube & Cap (black) 1 91734
25201 M3 x 8mm FHCS 20
91748
25202 M3 x 10mm FHCS 20
25204 M3 x 16mm FHCS 20 91747
25225 M3 x 3mm Set Screw 20
31541 M3 x 6mm FHCS 10
89203 M3x16mm BHCS 10
91652 Side Rails, B6 Pr. 91749
91670 Hinge Pin Set, B6 1
91685 Bumpers, B6 1 ea. 91749
91688 Aluminum Arm Mount (D), B6 1 91749
91734 Battery Foam, B6 1 91749
91749
91747 FT B6 Steel Chassis Weight, 24g 1
91748 FT B6 Steel Chassis Weight, 36g 1 91749
91749 M2x3mm FHCS 10
91772 B6.1 Aluminum Arm Mount (C) 1
91850 B6.2 Chassis, +3mm 1 91850
91855 B6.2 Rear Arms/Shims, 75mm Pr.
91867 B6.2 Fan Mount 1
92014 Arm Mount Inserts 4 ea.
25225 91867

92014
6338
91855 91688
89203
92014 91670
92014
91670 91855 25202
91772 91685
91652 25201
25201
92014 25202
31541 25204
25202
 29
:: Factory Team and Option Parts :: Factory Team and Option Parts Cont...
1369 FT Alum. Clamping Servo Horn 23T, 15.5 mm 1 91802 B6.1 Vented Slipper Hub, (inner) 1
1370 FT Alum. Clamping Servo Horn 25T, 15.5 mm 1 91806 B6.1 Vented Slipper Hub, outer 1
27128 Servo Washers, Black Aluminum 4 91807 B6.1 HTC Vented Slipper Hub, outer & center disk 1
71034 FT Clamping Wheel Hexes, 6.0 mm 2 91821 B6.1 Anti-Roll Bar Hardware Set 1
91494 FT 12mm Machined Shock Spacers, V2 1 91822 B6.1 Front Anti-Roll Bar Set (Soft) 0.8, 0.9, 1.0 1
91495 12mm V2 X-Ring Rebuild Kit 1 91823 B6.1 Rear Anti-Roll Bar Set (Med) 1.2, 1.3, 1.4 1
91553 Factory Team Bearing Kit, B5, B6 1 91825 B6.1/B6.1D FT Chassis Protective Sheet 1
91580 Titanium Screws, 3x6mm BHCS 4 91854 RC10B6.2 Rear Suspension Arms, 73mm, Hard 2
91581 Titanium Screws, 3x8mm BHCS 4 91856 RC10B6.2 Rear Suspension Arms, 75mm, Hard 2
91582 Titanium Screws, 3x10mm BHCS 4 91858 B6.2 CVA Axles 2
91583 Titanium Screws, 3x12mm BHCS 4 91862 B6.2 Clamping Wheel Hexes, 4.0mm 1
91584 Titanium Screws, 3x14mm BHCS 4 91868 B6.2 FT Bearing Set 2
91585 Titanium Screws, 3x16mm BHCS 4 92100 FT Aluminum Wing Buttons 2
91587 Titanium Screws, 3x20mm BHCS 4 92185 B74 FT Graphite Rear Hub Link Shim Set 1
91588 Titanium Screws, 3x22mm BHCS 4
91589 Titanium Screws, 3x24mm BHCS 4
91591 Titanium Screws, 3x6mm FHCS 4
91592 Titanium Screws, 3x8mm FHCS 4
91593 Titanium Screws, 3x10mm FHCS 4
91594 Titanium Screws, 3x12mm FHCS 4
91595 Titanium Screws, 3x14mm FHCS 4
91596 Titanium Screws, 3x16mm FHCS 4
91597 Titanium Screws, 3x18mm FHCS 4
91609 Clamping Wheel Hex, (5.0mm) 2
91625 FT 12 mm Pistons V2, 2x1.5 mm, flat 4
91626 FT 12 mm Pistons V2, 2x1.6 mm, flat 4
91627 FT 12 mm Pistons V2, 2x1.7 mm, flat 4 :: Bodies
91628 FT 12 mm Pistons V2, 3x1.4 mm, flat 4 91741 RC10B6 Wing 1
91653 B6 Side Rails, hard Pr. 91743 Adhesive Hook and Loop 1
91658 RC10B6 Aluminum Front Bulkhead 1 91863 RC10B6.2 Clear Body 1
91659 RC10B6 Brass Front Bulkhead 1 91864 RC10B6.2 Lightweight Clear Body 1
91668 RC10B6 Aluminum Steering Bell Crank 1 91866 RC10B6.2 Front Wing Clear 2
91669 RC10B6 Aluminum Steering Rack 1 91869 RC10B6.2 Decal Sheet 1
91672 RC10B6 Flat Front Arm, Hard Pr.
91673 RC10B6 Gull Front Arm - Req. #91663 Pr.
91674 RC10B6 Gull Front Arm, Hard - Req. #91663 Pr.
91680 B6 FT Steering Block Arms, +1 Pr.
91683 RC10B6 Titanium Front Axle 2 :: Lubes & Adhesives / Decals / Misc.
91696 RC10B6 Rear Arm, Hard Pr.
1105 FT Green Slime Shock Lube 1
91699 FT Aluminum Rear hub Link 2
1596 FT Locking Adhesive 1
91707 RC10B6 Stand-Up Gear Box, 4 Gear - 1
1597 FT Tire Adhesive, medium 1
Req. #91711, #91714
6588 Black Grease - 4cc 1
91711 RC10B6 Gear Cover, 4 Gear - 1
6591 S.Diff Lube - 4cc 1
Req. #91707, #91714
6636 Silicone Grease - 4cc 1
91714 RC10B6 Stand-Up Motor Plate, 4 Gear 1
6727 Servo Tape 2
Req. #91707, #91711
91744 FT Brass Under Battery Weights 1
726 Reedy 2016 Sticker Set 1
91745 RC10B6 Aluminum Chassis Weight (9g) 1
3840 2016 Team Associated Decal Sheet 1
91746 RC10B6 Aluminum Chassis Weight (13g) 1
9787 FT Chassis Protective Sheet 1
91747 RC10B6 Steel Chassis Weight (24g) 1
91748 RC10B6 Steel Chassis Weight (36g) 1
91749 M2 x 3mm FHCS - Use with Chassis Weights 6
91750 HD Titanium Ball Stud, 4mm 2
91751 HD Titanium Ball Stud, 6mm 2 :: MyLaps Transponders
91752 HD Titanium Ball Stud, 8mm 2
MLP10R120 MyLaps RC4 (3-wire) Transponder 1
91753 HD Titanium Ball Stud, 10mm 2
MLP10R147 MyLaps RC4 (3-wire) Pro Transponder, Black 1
91754 FT Graphite ESC Plate 1
MLP40R222 MyLaps Transponder Holder 1
91760 B6 FT Blue Aluminum Rear Hubs Pr.
91761 FT Graphite Servo Plate 1
91768 RC10B6.1 Front Shock Tower, (Gull-Wing) - 1
Graphite Req. #91673 or #91674
91773 B6.1 Brass Arm Mount (C), Req. #92014 1
91781 B6.1 Gear Diff Cover, aluminum 1 :: Reedy Batteries
91784 B6.1 Aluminum Cross Pins 2 302 AA Alkaline 1.5V (4) 1
91786 B6.1 Gear Diff Kit 1 27313 LiPo Pro TX/RX 2400mAh 7.4V Flat 1
91788 B6.1 Standup Gearbox Req. #91794 1 27315 LiFe Pro TX/RX 1600mAh 6.6V Flat 1
91790 B6.1 Layback Gearbox 1 27318 Wolfpack HV LiPo 50C 4200mAh 7.6V Shorty 1
91793 B6.1 Alum. Differential Height Inserts, black 2 Pr. 27319 Wolfpack HV LiPo 50C 3300mAh 7.6V LP Shorty 1
91796 FT Laydown/Layback Motor Plate, graphite 1 27335 Zappers SG2 4800mAh 7.6V 110C Shorty 37Wh 205g 1
91797 Titanium Top Shaft Screw 1 27336 Zappers SG2 5800mAh 7.6V 80C Shorty 45Wh 220g 1
91798 B6.1 Standup Top Shaft 1 27337 Zap. SG2 3600mAh 7.6V 110C LCG Shrt 28Wh 155g 1
91799 B6.1 Laydown Top Shaft 1 27338 Zap. SG2 4100mAh 7.6V 80C LCG Shrt 32Wh 152g 1
91800 B6.1 Direct Drive Kit 1
91801 B6.1 Slipper Spring 1
30
:: Reedy Competition Motors & Spare Parts :: Reedy Chargers / Charger Accessories
262 Sonic 540-M3 6.5 1 996 5.0mm 1S-2S Balance Charge lead w/SP Clip (4mm) 1
263 Sonic 540-M3 6.0 1 997 4.0mm 1S-2S Balance Charge lead w/SP Clip (4mm) 1
264 Sonic 540-M3 5.5 1 27200 1216-C2 Dual AC/DC Competition Batt. Charger 1
265 Sonic 540-M3 5.0 1 27220 7-in-1 Universal Charge Lead (4mm) 1
266 Sonic 540-M3 4.5 1 27221 Reedy T-Plug Charge Lead, (4mm) 1
272 540-M3/S-Plus Spec Rotor 12.2 x 7.25 x 25.3 1 27222 XH 2-6S Balance Board (4mm) 1
273 540-M3/S-Plus Spec Rotor 12.5 x 7.25 x 25.3 1 27223 RX Charger Lead FUT (4mm) 1
274 Sonic 540-M3 Mod Rotor 12.3 x 5.0 x 25.3 1 27224 US to IEC 320 C5 angle 1M AC Power Cord 1
275 Sonic 540-M3 Mod Rotor 12.5 x 5.0 x 25.3 1 27226 EU to IEC 320 C5 angle 1M AC Power Cord 1
276 Sonic 540-M3 Mod Rotor 13.0 x 5.0 x 25.3 1 27228 AU to IEC 320 C5 angle 1M AC Power Cord 1
277 Sonic 540-M3 Stainless Steel Bearing Set 1 27232 Reedy 4mm/5mm Pro Charge Lead 1
280 Sonic 540-M3 Sensor Assembly 1
286 540-M3/S-Plus Spec Rotor 12.3 x 7.25 x 25.3 1
293 Sonic 540 FT 17.5 Fixed Timing 1
294 Sonic 540 FT 13.5 Fixed Timing 1
295 Sonic 540-FT Spec Rotor 12.0 x 7.25 x 25.3 1
296 Sonic 540-M3 Mod Rotor 12.0 x 5.0 x 24.2 1
27402 S-Plus 17.5 Spec 1
27403 S-Plus 13.5 Spec 1
27404 S-Plus 10.5 Spec - Torque 1
27414 540-M3/S-Plus Spec Rotor 12.5 x 7.15 x 24.2 1
27418 540-M3/S-Plus Lightweight Sensor Board 1
27419 S-Plus Front Plate 1
27420 540-M3/S-Plus Aluminum Case Screw Set 1
27421 540-M3/S-Plus Aluminum Timing Screw Set 1 :: Reedy Servos & Accessories
27429 S-Plus 17.5 Spec - Torque 1 27100 RS1206 Digital HV Hi-Speed Competition Servo 1
27101 RT1508 Digital HV Hi-Torque Competition Servo 1
27102 RS1206 Servo Case Set w/screws 1
27103 RS1206 Servo Gear Set 1
27105 RT1508 Servo Gear Set 1
27112 RS1306 Digital HV Low-Profile Brushless Comp. Servo 1
27113 RT1709 Digital HV Low-Profile Brushless Comp. Servo 1
27114 RT2406 Digital HV Brushless Comp. Servo 1
27115 RT2706A Digital HV Alum. Brushless Comp. Servo 1
27122 Reedy Aluminum Servo Horn (25) 1
27123 Reedy Aluminum Clamping Servo Horn (25) 1
27133 RS1306 Gear Set 1
:: Reedy Competition Motors Accessories 27134 RT1709 Gear Set 1
978 Flat Sensor Wire 70mm 1 27135 RT2406 Gear Set 1
979 Flat Sensor Wire 110mm 1 27136 RT2706A Gear Set 1
980 Flat Sensor Wire 150mm 1 27137 RS1306 Case Set 1
981 Flat Sensor Wire 200mm 1 27138 RT1709 Case Set 1
982 Flat Sensor Wire 270mm 1 27139 RT2406 Case Set 1
994 Flat Sensor Wire 125mm 1
995 Flat Sensor Wire 175mm 1
27423 30mm Motor Fan w/195mm extension 1

:: Reedy Accessories
643 Low Profile Bullet Plug 4mm x 14mm (2) 1
644 Low Profile Bullet Plug 4mm x 14mm (10) 1
645 Low Profile Bullet Plug 5mm x 14mm (2) 1
:: Reedy ESC’s 646 Low Profile Bullet Plug 5mm x 14mm (10) 1
27002 Blackbox 800Z 2S Zero-Timing Competition ESC 1 647 Silicone Wire 12AWG-Black (1m) 1
27004 Blackbox 510R Competition ESC 1 648 Silicone Wire 14AWG-Black (1m) 1
27005 Blackbox 510R Competition ESC w/PROgrammer2 1 650 Shrink Tubing - 15pcs 4.5mm x 20mm 1
27006 Blackbox 600Z 2S Zero-Timing Competition ESC 1 747 Silicone Wire 12AWG-Black (30m) 1
27024 Blackbox Pro Capacitor Unit 1 790 Silicone Wire 13AWG-Black (1m) 1
27027 Blackbox PROgrammer2 1 791 Silicone Wire 13AWG-Black (30m) 1
27028 Blackbox 30x30x7mm Fan w/screws 1 792 Low Profile Caged Bullet Plug 4mm x 14mm (2) 1
27029 Blackbox Pro Modified Capacitor Unit 1 793 Low Profile Caged Bullet Plug 4mm x 14mm (10) 1
27030 Blackbox ESC/Programmer2 Connection Wire 1 794 Low Profile Caged Bullet Plug 5mm x 14mm (2) 1
27031 Blackbox 510R 30x30x10mm Fan w/screws 1 795 Low Profile Caged Bullet Plug 5mm x 14mm (10) 1
27033 Blackbox 1000Z+ Pro Competition ESC 1 27304 LiPo Battery Weight Set - Shorty 1
 31
:: Apparel / Promotional :: Tools
TEE SHIRTS 1111 FT Turnbuckle Wrench 1
SP124* AE 2017 Worlds Tee, Black (S, M, L, XL-5XL) 1 1112 FT 4mm Turnbuckle Wrench 1
SP126* Team Associated Tri T-Shirt, Black (S, M, L, XL-5XL) 1 1113 12mm Big Bore Shock Tool 1
SP200* Element RC Logo Tee, Gray (S, M, L, XL-5XL) 1 1114 FT Dual Turnbuckle Wrench 1
SP201* Element RC Rhombus Tee, Black (S, M, L, XL-5XL) 1 1449 Off Road Ride Height Gauge 1
1452 FT TC Ride Height Gauge 1
1498 FT Universal Tire Balancer 1
HOODIES/JACKETS 1499 FT Body Reamer 1
SP142* Reedy W19 Hoodie - Black (S, M, L, XL-3XL) 1 1500 FT 1.5mm Hex Driver 1
SP230 Element RC Zip Up, Black (S, M, L, XL-5XL) 1 1501 FT 2.0mm Hex Driver 1
SP231 Element RC Hoodie, Black (S, M, L, XL-5XL) 1 1502 FT 2.0mm Ball Hex Driver 1
SP250 Element RC Jacket, Black (S, M, L, XL-2XL) 1 1503 FT 2.5mm Hex Driver 1
1504 FT 2.5mm Ball Hex Driver 1
HATS 1505 FT 3.0mm Hex Driver 1
SP20 AE Patch Trucker Hat 1 1506 FT 5.0mm Hex Driver 1
SP430 Reedy Trucker Hat 2018 1 1507 FT 5.5mm Nut Driver 1
SP260 Element RC Hat, Curved Bill, Black 1 1508 FT 7.0mm Nut Driver 1
SP261 Element RC Hat, Flat Bill, Black 1 1510 FT 1.5mm Hex Replacement Tip 1
SP262 Element RC Beanie, Black 1 1511 FT 2.0mm Hex Replacement Tip 1
1512 FT 2.0mm Ball Replacement Tip 1
BANNERS/MATS CARRIERS 1513 FT 2.5mm Hex Replacement Tip 1
SP115 Reedy Circuit Cloth Banner 1 1514 FT 2.5mm Ball Replacement Tip 1
SP280 Element RC Counter Top Mat 1 1515 FT 3.0mm Hex Replacement Tip 1
SP281 Element RC Pit Mat 1 1518 FT Hex Driver Tool Set (3pcs) 1
SP282 Element RC Pit Towel 1 1519 FT Hex/Nut Driver Tool Set (5pc) 1
SP283 Element RC Vinyl Banner, 48x24 1 1522 FT Digital Scale, 100/0.01g 1
SP284 Element RC Vinyl Banner, 20x12 1 1555 FT Clutch Gauge, 4 Shoe 1
SP285 Element RC Pin Pattern Counter Top Mat 1 1568 FT 5.5mm Short Nut Driver 1
SP425 FT Fluid Carrier 1 1569 FT 7mm Nut Driver, T-Handle 1
1570 FT 5.5mm Short Nut Driver 1
1571 FT 1:8 Wheel Nut Wrench, 17mm Hex 1
1579 FT Ball Cup Wrench 1
1595 Chassis Weights, 1/4 oz 1
1650 7 Piece Hex Driver Set 1
** Use part number plus the desired size when ordering! 1657 FT 1/4” Hex Drive .050” Tip 1
1658 FT 1/4” Hex Drive 1/16” Tip 1
1659 FT 1/4” Hex Drive 5/64” - 2.0mm Tip 1
1660 FT 1/4” Hex Drive 3/32” Tip 1
1661 FT 1/4” Hex Drive 1.5mm Tip 1
1662 FT 1/4” Hex Drive 2.5mm Tip 1
1666 FT 1/4” Hex Drive 5.5mm Nut Driver Tip 1
1667 FT 1/4” Hex Drive 7.0mm Nut Driver Tip 1
1668 FT 1/4” Hex Drive 8.0mm Nut Driver Tip 1
1674 FT 1/4” 5 Piece Power Tool Tips Set (5/64-2.0mm, 1
1.5mm, 2.5mm, 5/64”- 2.0mm ball, 2.5mm ball)
1675 FT Shock Shaft Pliers 1
1679 FT T-Handle Ratchet Driver 1
1719 FT Camber + Track Width Tool 1
1737 FT Body Scissors 1
3718 12 Inch Nylon Wire Ties 12
3987 FT Droop Gauge 1
89240 RC8 FT Turnbuckle Wrench 1

:: Contact Information
Check out the following web sites for all of our electric kits,
current products, new releases, setup help, tips, and racing info!

Associated Electrics, Inc.

21062 Bake Parkway
Lake Forest, CA 92630-8853 USA
http://www.TeamAssociated.com
http://www.RC10.com
http://twitter/Team_Associated
http://www.instagram.com/teamassociatedrc/
http://www.facebook.com/TeamAssociated/

call: (949) 544-7500

fax: (949) 544-7501
 Driver: B6.2 Kit Setup Event:
Date: Track:
Qualify: TQ: Main: Finish: Best Lap Time:
Front Suspension:
Ride Height: 16mm Bump Steer Spacing: 0mm Ball Stud Spacing: 0mm
Camber: -1°
Toe: +1°
Anti-Roll Bar: #91822 Blue, 1.0mm Steering Plate: #91680 +1
Arm Type: #91673 Gull-Wing, Standard 3
2
1
Tower Type: #91768 Gull-Wing Steering Stop Spacing: 0mm Axle Height: Ball Stud Spacing: 1mm
Caster Block Insert: 5° +3
+2 BA
Steering Block: 4mm
+1
Bulkhead Type: #91656 Plastic 0 321
Kick-Up Angle: 25°
Wheel Hex: #91682 Aluminum, 5mm
Notes: Caster Block Spacing: 1mm
CBA

Rear Suspension:
Ride Height: 16mm C Mount Inserts: 1° 0 .5° D Mount Inserts: 1° 0 .5°
Camber: -2° Aluminum Brass Aluminum Brass
Tower Type: #91769 Standard
Wheel Hex: #91609 Aluminum, 5.0mm
32
CVA Bone Length: 69mm 1
CVA Pin Location: Towards Hex
Rear Axle Height
Anti-Roll Bar: #91823 Gray, 1.3mm Camber Link Spacing: 2mm
3 3 +3mm
0
Arm & Position:
Ball Stud Spacing: 2mm
73 75 Forward Back 2
1
2 +2mm
Hub Spacing: Ball Stud Spacing: 4mm
1 1 +1mm
2
Forward Middle Back
Shock Mounting Position: 321
0 0 +0mm C BA
3
Front of Arm Rear of Arm
Notes:

Electronics: Drivetrain: Shocks:

Radio: Servo: Transmission: Laydown: Front Rear
EPA: Throttle: % Brake: % 3 Gear: Layback: Piston: 2 x 1.6 2 x 1.8
ESC: 4 Gear: Stand Up: Fluid: 40 30
ESC Settings: Differential: Ball Diff: Spring: #91835 Red #91840 Blue
Motor: Height: 3 Gear Diff: Int. Limiters: 0 0
Wind: Timing: Gear Diff Mass: Ext. Limiters: 0 1
Stroke
Pinion: Spur: Notes: Stroke: 24.0 28.0
Battery: Slipper Clutch: Eyelet Length: Short Long
Battery Position: 3F Type: Kit Cup Offset: 5mm 0mm
Battery Weight: # of Pads: 2 Notes:
Track Info: Tires: Chassis, Body, Wing:
Size: Small Medium Large Extra Large Front Tires: Body: Kit
Surface: Dirt Carpet Astroturf Multi Surface Front Compound: Front Wing: Kit
Traction: Low Medium High Very High Front Insert: Rear Wing: Kit
Moisture: Dry Damp Wet Rear Tires: Wing Angle: 0° 3° 6°
Condition: Indoor Outdoor Dusty Hard Packed Rear Compound: Chassis Length:
Bumpy Grooved Smooth Loamy Rear Insert: Servo Weights: #91747, Steel 24g
Temperature: Ambient: Track: Wheel (F/R): Electronic Weights: #91748, Steel 36g
Notes: Notes: Total Vehicle Weight:
Vehicle Comments:
:: For more setups, visit RC10.com and click on “Setup Sheets”
 Driver: Event:
Date: Track:
Qualify: TQ: Main: Finish: Best Lap Time:
Front Suspension:
Ride Height: Bump Steer Spacing: Ball Stud Spacing:
Camber:
Toe:
Anti-Roll Bar: Steering Plate:
Arm Type: 3
2
1
Tower Type: Steering Stop Spacing: Axle Height: Ball Stud Spacing:
Caster Block Insert: +3
+2 BA
Steering Block:
+1
Bulkhead Type: 0 321
Kick-Up Angle:
Wheel Hex:
Notes: Caster Block Spacing:
CBA

Rear Suspension:
Ride Height: C Mount Inserts: 1° 0 .5° D Mount Inserts: 1° 0 .5°
Camber: Aluminum Brass Aluminum Brass
Tower Type:
Wheel Hex:
32
CVA Bone Length: 1
CVA Pin Location:
Rear Axle Height
Anti-Roll Bar: Camber Link Spacing:
3 3 +3mm
0
Arm & Position:
Ball Stud Spacing:
73 75 Forward Back 2
1
2 +2mm
Hub Spacing: Ball Stud Spacing:
1 1 +1mm
2
Forward Middle Back
Shock Mounting Position: 321
0 0 +0mm C BA
3
Front of Arm Rear of Arm
Notes:

Electronics: Drivetrain: Shocks:

Radio: Servo: Transmission: Laydown: Front Rear
EPA: Throttle: % Brake: % 3 Gear: Layback: Piston:
ESC: 4 Gear: Stand Up: Fluid:
ESC Settings: Differential: Ball Diff: Spring:
Motor: Height: Gear Diff: Int. Limiters:
Wind: Timing: Gear Diff Mass: Ext. Limiters:
Stroke
Pinion: Spur: Notes: Stroke:
Battery: Slipper Clutch: Eyelet Length:
Battery Position: Type: Cup Offset:
Battery Weight: # of Pads: Notes:
Track Info: Tires: Chassis, Body, Wing:
Size: Small Medium Large Extra Large Front Tires: Body:
Surface: Dirt Carpet Astroturf Multi Surface Front Compound: Front Wing:
Traction: Low Medium High Very High Front Insert: Rear Wing:
Moisture: Dry Damp Wet Rear Tires: Wing Angle: 0° 3° 6°
Condition: Indoor Outdoor Dusty Hard Packed Rear Compound: Chassis Length:
Bumpy Grooved Smooth Loamy Rear Insert: Servo Weights:
Temperature: Ambient: Track: Wheel (F/R): Electronic Weights:
Notes: Notes: Total Vehicle Weight:
Vehicle Comments:
:: For more setups, visit RC10.com and click on “Setup Sheets”