WACKER® SILICONE PASTE P
SILICONE PASTE
Product description Heat-resistance release agent for
WACKER® SILICONE PASTE P is a translucent, - extruder die rings
vaseline-like, relatively stiff, waterrepellent paste. - slightly porous surfaces of moulds for demoulding
WACKER® SILICONE PASTE P becomes softer when rubber and plastics mouldings and cast resin parts
subjected to shear stress or other mechanical stress - heat-sealing instruments such as used for
such as kneading, which in many instances makes Packaging Film, where a thin film of
processing easier. WACKER® SILICONE PASTE P applied to the
The pasty consistency is little affected by changes in welding bars prevents sticking
temperature. The components of Paste P are on the
positive lists of the following Regulations for food For detailed information, refer to brochures on
contact: Regulation (EU) No. 10/2011, www.wacker.com.
Recommendation XV. Silicones of the BfR (Federal
Institute for Risk Assessment) and the FDA Code of
Federal Regulations Title 21 §175.3570 Lubricants Storage
with Incidental Food Contact.
Further information for storage:
Application Store in a dry and cool place.
The 'Best use before end' date of each batch is shown
Assembly aid and lubricant for elastomers, especially on the product label.
O-rings.
Storage beyond the date specified on the label does
WACKER® SILICONE PASTE P is easy to apply. not necessarily mean that the product is no longer
There is no dripping as when using oil. Larger parts usable. In this case however, the properties required
are greased with the pure paste by hand or with a for the intended use must be checked for quality
brush; smaller parts in large quantities are put into a assurance reasons.
plastic bag with some paste and kneaded until the
paste has been distributed over their surfaces.
Safety notes
Silicon pastes have only a slight swelling effect on
most organic elastomers. For lubricating purposes and Comprehensive instructions are given in the
as assembly aid for materials with critical swelling corresponding Material Safety Data Sheets. They are
characteristics we would, however, recommend using available on request from WACKER subsidiaries or
silicone product WACKER®POWERSIL® PASTE AP, may be printed via WACKER web site
which is especially designed for causing low swelling http://www.wacker.com.
of bordering elastomers.
Technical data sheet for WACKER® SILICONE PASTE P / Version: 1.9 / Date of last alteration: 02.02.2017 1/2
Product data
Typical general characteristics Inspection Method Value
Appearance colorless, opaque
Density at 25 °C ISO 1183-1 A 1 g/cm³
Consistency a) unworked penetration DIN ISO 2137 180 - 220 1/10 mm
Consistency b) worked penetration (60 strokes) DIN ISO 2137 250 1/10 mm
Solidifying point approx. -45 °C
Operating temperature range - 40 to + 200 °C
Loss of weight / Volatility FED-STD 791 M 321; max. 2 %
30h / 200 °C
Bleeding FED-STD 791 M 321; max. 8 %
30h / 200 °C
Dielectric strength IEC 60243 20 kV/mm
Dielectric Constant (50 Hz) IEC 60250 2,8 εr
Dissipation factor (50 Hz) IEC 60250 0,0005
Insoluble in water, methanol, ethanol,
glycerol, glycol
Soluble or dispersible in methylene chloride,
benzine, white spirit,
petroleum ether, toluene,
kerosene, ethyl acetate etc.
These figures are only intended as a guide and should not be used in preparing specifications.
The data presented in this medium are in accordance with the present state of our knowledge but The management system For technical, quality, or
do not absolve the user from carefully checking all supplies immediately on receipt. We reserve the has been certified product safety questions,
right to alter product constants within the scope of technical progress or new developments. The according to please contact:
recommendations made in this medium should be checked by preliminary trials because of DIN EN ISO 9001 and
conditions during processing over which we have no control, especially where other companies’ DIN EN ISO 14001 Wacker Chemie AG
raw materials are also being used. The information provided by us does not absolve the user from Hanns-Seidel-Platz 4
the obligation of investigating the possibility of infringement of third parties’ rights and, if necessary, WACKER® is a trademark 81737 München, Germany
clarifying the position. Recommendations for use do not constitute a warranty, either express or of [email protected]
implied, of the fitness or suitability of the product for a particular purpose. Wacker Chemie AG.
www.wacker.com
Technical data sheet for WACKER® SILICONE PASTE P / Version: 1.9 / Date of last alteration: 02.02.2017 2/2
