VAL AVIONICS LTD

NAV 2000
ULTRA-THIN NAVIGATION RECEIVER

Installation and
Operator’s Manual
Revision 2
Oct. 2014

P/N 172203-2
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N R E C E I V E R
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

This Page Intentionally

Left Blank

Revision 2 Page 2 of 2
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N R E C E I V E R
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

Table of Contents
1 SECTION I - GENERAL INFORMATION ............................................................................................................................. 5
1.1 INTRODUCTION ................................................................................................................................................................. 5
1.2 SCOPE................................................................................................................................................................................... 5
1.3 EQUIPMENT DESCRIPTION.............................................................................................................................................. 5
1.4 SPECIFICATIONS................................................................................................................................................................ 6
1.5 EQUIPMENT SUPPLIED..................................................................................................................................................... 7
1.6 EQUIPMENT REQUIRED BUT NOT SUPPLIED .............................................................................................................. 7
1.7 LICENSE REQUIREMENTS ............................................................................................................................................... 7
2 SECTION II - INSTALLATION ............................................................................................................................................... 8
2.1 GENERAL INFORMATION ................................................................................................................................................ 8
2.2 UNPACKING AND INSPECTION ...................................................................................................................................... 8
2.3 EQUIPMENT REQUIREMENTS......................................................................................................................................... 8
2.3.1 Cooling Requirements................................................................................................................................................ 8
2.3.2 Mounting Requirements............................................................................................................................................. 8
2.3.3 Wire Harness Fabrication........................................................................................................................................... 8
2.4 NAV 2000 INSTALLATION PROCEDURES ..................................................................................................................... 9
2.4.1 Mounting.................................................................................................................................................................... 9
2.4.2 Antennas .................................................................................................................................................................... 9
2.4.3 Audio ......................................................................................................................................................................... 9
2.4.4 Electrical.................................................................................................................................................................... 9
2.5 Configuration and Initial Testing ........................................................................................................................................... 9
2.5.1 Initial Unit Test .......................................................................................................................................................... 9
2.5.2 Configuration ............................................................................................................................................................. 9
2.6 POST INSTALLATION CHECK ....................................................................................................................................... 10
2.6.1 Operational Check ................................................................................................................................................... 10
2.6.2 Final Inspection........................................................................................................................................................ 10
2.7 LIMITATIONS ................................................................................................................................................................... 10
3 SECTION III - OPERATION .................................................................................................................................................. 11
3.1 Display Functions ................................................................................................................................................................ 11
3.2 User Controls....................................................................................................................................................................... 11
3.2.1 Turning the unit on/off ............................................................................................................................................. 11
3.2.2 Setting Active and Standby Frequency .................................................................................................................... 11
3.2.3 Setting a Bearing...................................................................................................................................................... 12
3.2.4 Changing the Volume .............................................................................................................................................. 12
3.3 Memory ............................................................................................................................................................................... 12
3.3.1 Selecting a Stored Memory Station.......................................................................................................................... 12
3.3.2 Entering / Editing / Deleting a Stored Memory Station............................................................................................ 12
3.3.3 Selecting a stored frequency to be created / edited /deleted ..................................................................................... 12
3.3.4 Creating / Editing a stored frequency....................................................................................................................... 12
3.3.5 Deleting a Stored frequency..................................................................................................................................... 13
3.3.6 Exiting the stored frequency editing functions ......................................................................................................... 13
3.4 System Configuration .......................................................................................................................................................... 13
3.4.1 Accessing Setup Functions....................................................................................................................................... 13
3.4.2 Configuration Options.............................................................................................................................................. 13
3.4.3 OBS/Resolver Selection (Rs I).............................................................................................................................. 13
3.4.4 Resolver Test (Rs T) .............................................................................................................................................. 14
3.4.5 Resolver Calibration (RsCl) ................................................................................................................................... 14
3.4.6 Serial Mode (SrMd)................................................................................................................................................. 15
3.4.7 VOR Calibration (VORC) ......................................................................................................................................... 15
4 SECTION IV - WARRANTY AND SERVICE....................................................................................................................... 16
4.1 LIMITED WARRANTY ..................................................................................................................................................... 16
4.2 SERVICE ............................................................................................................................................................................ 16
5 Appendix A – INSTALLATION DRAWINGS AND CONNECTOR LAYOUT.................................................................. 17
6 Appendix B – WIRING DIAGRAMS ...................................................................................................................................... 20
7 Appendix C – INSTRUCTIONS FOR CONTINUED AIRWORTHINESS ......................................................................... 22
7.1 MAINTENANCE INSTRUCTIONS................................................................................................................................... 22
8 Appendix D – RS-232 Instruction Listing................................................................................................................................ 23
8.1 Input Commands.................................................................................................................................................................. 23
8.2 Output Messages.................................................................................................................................................................. 23
8.3 Data Format ......................................................................................................................................................................... 23
8.4 Default Message Output ...................................................................................................................................................... 23
8.5 Message Formats ................................................................................................................................................................. 24
8.6 Message Definitions ............................................................................................................................................................ 25
9 Appendix E – Installation Checkout Log................................................................................................................................. 33

Revision 2 Page 3 of 3
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N R E C E I V E R
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

Table of Figures and Tables

Table 1: Specifications ........................................................................................................................................................................... 6
Table 2: Equipment Supplied ................................................................................................................................................................. 7
Table 3: Equipment Not Supplied .......................................................................................................................................................... 7
Table 4: Rear Connector Pin Functions ................................................................................................................................................ 19
Table 5 - Data Output Requests............................................................................................................................................................. 25

Figure 1: NAV 2000 Displays showing Active and Standby Frequencies ............................................................................................. 11
Figure 2: NAV 2000 Button Controls.................................................................................................................................................... 11
Figure 3: NAV 2000 in Configuration Mode......................................................................................................................................... 13
Figure 4: NAV 2000 showing Resolver Test ......................................................................................................................................... 14
Figure 5: Analog OBS indicator set to 150............................................................................................................................................ 14
Figure 6: Resolver Cal showing 150...................................................................................................................................................... 14
Figure 7: Resolver Cal showing 120...................................................................................................................................................... 14
Figure 8: Serial Mode Selection ............................................................................................................................................................ 15
Figure 9: VOR Calibration Selection..................................................................................................................................................... 15
Figure 10: Physical Dimensions ........................................................................................................................................................... 17
Figure 11: P1 Connector Pin Out.......................................................................................................................................................... 18
Figure 12: Panel Cut Out ...................................................................................................................................................................... 18
Figure 13: Mounting Tray Assembly Exploded View .......................................................................................................................... 18
Figure 14: NAV 2000 Basic Wiring Diagram ....................................................................................................................................... 20
Figure 15: NAV 2000 to Nav Indicator ................................................................................................................................................. 20
Figure 16: NAV 2000 to Nav Converter................................................................................................................................................ 20

Revision History:
2: Revised Section numbering to reduce sub-headings
Changed Section 3.4.5 and added 3.4.5.1 regarding the changes to the Resolver Calibration.
Added multiple pictures to better explain the operation of the calibration of the unit.
Revised Section 2 and Section 3 to improve installation flow
Added Appendix E – Installation Checkout Log to provide a clear testing procedure
Added Section 3.3 regarding memory functions
1: Added Section 3.2.3 and expanded section 3.4.3 regarding the Non option and setting an OBS using
the internal OBS controls.
0: Initial publishing

Revision 2 Page 4 of 4
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N R E C E I V E R
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

1 SECTION I - GENERAL INFORMATION

1.1 INTRODUCTION
Thank you for purchacing our NAV 2000 Navigation Receiver. Here at Val Avionics Ltd., our core design
philosophy is based on the ease of installation and use. The NAV 2000 represents a new direction and
continued improvement of our product line. The NAV 2000 contains continuing improvements from the
INS 429,based on the feedback of customers. The NAV 2000 is a continuation of our Ultra-thin series,
designed with new and exciting features.

That design philosophy translates into the ease of installation and simple operation the makes the NAV
2000 a navigation solution for a wide variety of aircraft panels, from the Homebuilt through light twins.
The NAV 2000 satisfies the need for compact, fully intergraded, quality navigational aid that can be
counted on to provide years of reliable service.

Before installing and /or using your new NAV 2000 please read this manual completely. This will ensure
proper installation and familiarize you with all of the features your new NAV 2000 has to offer.

1.2 SCOPE

This manual will provide detailed information about the installation and operation of the NAV 2000
Navigation Receiver. It will also provide equipment limitation information and instructions for continued
airworthiness.

1.3 EQUIPMENT DESCRIPTION

The NAV 2000 has been designed for simplicity. It is straight forward to install and operate. Using state of
the art technology Val Avionics Ltd. has created a navigation receiver that will provide the pilot with
simple, easy to interpret navigation information for in-route VOR navigation and ILS Approaches.

The NAV 2000 also has an enhanced display that features both active and standby frequency displays.

The unit’s controls have been designed for simple user interface. The concentric knobs on the left side of
the unit select the Volume output level with push button access to frequently used frequencies. The
concentric knobs on the right side of the unit select the desired standby frequency and a push of the button
swaps the active and standby freqencies.

The NAV 2000 has two internal receivers. The VOR/LOC receiver operating from 108.00 MHz to 117.95
MHz and the Glide Slope receiver which operates from 329.15 MHz to 335.0 MHz.

Revision 2 Page 5 of 5
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N R E C E I V E R
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

1.4 SPECIFICATIONS

Table 1: Specifications
SPECIFICATIONS CHARACTERISTICS
Environmental RTCA/DO160D
VOR RTCA/DO-196
Localizer RTCA/DO-195
Glide slope RTCA/DO-192

Physical Dimensions:
Height 1.0 inches (2.54 cm)
Width 6.25 inches (15.88 cm)
Depth 9.0 inches (22.86 cm)

Weight: 3.00 pounds (1.36 kg)

Mounting: Panel mounted, no shock mounting required

Temperature Range: -30 to +55 Celsius with short time operations at

+70 Celsius
Power Requirements:
Voltage 10.0 to 30.0 VDC
Current 0.50 Amp @ 14V, 0.30 Amp @ 28V

Receiver:
VHF Frequency (VOR/LOC) 108.00 to 117.95 MHz
Sensitivity 2 µV to provide 50% Standard Deflection
Channel Spacing (VOR/LOC) 50 KHz
UHF Frequency (Glide slope) 329.15 to 335.0 MHz
Sensitivity 20 µV to provide 50% Standard Deflection
Channel Spacing (Glide slope) 150 KHz

External Outputs:
Audio Output 10mv into a 600 ohm load
CDI Left/Right 150mv into 1K Load
CDI Up/Down 150mv into 1K Load
CDI Glide slope Flag 250mv into 1K Load
CDI VOR/LOC Flag 250mv into 1K Load
Composite Output 500mv into 1K Load

Manufacturer’s Model Number NAV 2000

Part Number VPN 0800120-1
FCC ID EZNNAV2000

Revision 2 Page 6 of 6
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N R E C E I V E R
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

1.5 EQUIPMENT SUPPLIED

Table 2: Equipment Supplied

PART NUMBER QTY DESCRIPTION
0800120 1 NAV 2000 NAVIGATION
SYSTEM
0651020 1 INSTALLATION KIT

1.6 EQUIPMENT REQUIRED BUT NOT SUPPLIED

Table 3: Equipment Not Supplied

QTY DESCRIPTION PART NUMBER
1 Interconnect Wire Harness VPN 0751020 or field fabricated
1 Headphone Jack Switchcraft P/N 11 (Ref VPN
550017)
1 Circuit Breaker 2 amp Potter & Brumsfield W58-2 or
equivalant
1 Contact Crimping Tool w/ AMP P/N 601966-1
Positioning Tool AMP P/N 601699-5

1.7 LICENSE REQUIREMENTS

None

Revision 2 Page 7 of 7
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N R E C E I V E R
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

2 SECTION II - INSTALLATION
2.1 GENERAL INFORMATION
This section of the manual will provide the needed information to successfully complete the installation of
your new NAV 2000 Navigation Receiver. Please read this section completely before proceeding with the
installation process. Although the NAV 2000 installation procedures are designed with the do-it-yourself in
mind, we at Val Avionics Ltd. strongly suggest that you seek the advice of a qualified avionics installation
facility before beginning this or any other installation project. Qualified avionics installation technicians
can offer good advice as to time-tested installation practices and techniques that can save you many hours
of time and frustration.
2.2 UNPACKING AND INSPECTION
Use care when unpacking the equipment. Inspect the unit and supplied parts for visual signs of damage
during shipment. Examine the unit for loose screws, dents, broken buttons and other signs of damage that
may have occurred during shipment. Verify the contents of the container with the list in section 1.5. If any
damaged or missing parts are discovered during the inspection save the shipping material and contact the
freight carrier to file a claim. If it is suspected that parts were omitted from the container please feel free to
contact Val Avionics Ltd., to acquire the missing items.

2.3 EQUIPMENT REQUIREMENTS

2.3.1 Cooling Requirements
Forced air cooling is not required for the NAV 2000 Navigation Receiver. However, when planning the
location for mounting, ensure adequate spacing from heat producing sources such as heating or defrosting
ducts.

2.3.2 Mounting Requirements

The NAV 2000 mounting tray should be rigidly mounted in the avionics stack using the hardware provided
in the installation kit. Ensure that the mounting location will provide easy access and a clear view of the
equipment’s front panel from the pilot’s position. Ensure that the mounting position will provide adequate
clearance between the unit and the associated wire harness and the aircraft controls. Bracing at the rear of
the unit should be installed to ensure rigidity in the panel. Consult FAA Advisory Circular AC 43.13-2B for
acceptable practices and techniques.

2.3.3 Wire Harness Fabrication

Val Avionics Ltd. recommends that a factory fabricated wire harness (VPN 0751020) be used for the
installation of the NAV 2000 Navigation receiver. Use of the factory fabricated wire harness will ensure
proper operation of the NAV 2000, reduction in the occurrence of interfering signals and ground loops,
greatly reduced installation time, and provide prolonged trouble-free performance of your new equipment.
Contact Val Avionics Ltd. or your local avionics distribution center for NAV 2000 Wire Harness ordering
information.

Although strongly recommended, it is not required to use the factory fabricated wire harness when
installing the NAV 2000. A wiring harness can be fabricated in the field. Refer to appendix B of this
manual for a complete wiring diagram. The NAV 2000 is connected to the aircrafts avionics bus via a 2
AMP circuit breaker. All wires must be 22 AWG MIL-SPEC, unless otherwise noted in accordance with
current regulations. Two and three conductor shielded MIL-C-27500 or equivalent wire must be used
where indicated. Use AMP Contact Crimping Tool (AMP P/N 601966-1) with Positioning Tool (AMP P/N
601699-5) or equivalent to ensure good quality contacts. Refer to FAA Advisory Circular AC 43.13-2B for
acceptable practices and techniques.

Revision 2 Page 8 of 8
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N R E C E I V E R
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

2.4 NAV 2000 INSTALLATION PROCEDURES

2.4.1 Mounting
The NAV 2000 is rigidly mounted in the aircrafts avionics stack. Once a location has been selected, a
visual inspection should be made of the area directly behind the panel which will be occupied by the NAV
2000 and harness assembly for obvious obstructions such as heater ducts, control cables, fuel and oil lines
or any other obstruction. Pay particular attention to the control yoke assembly. It should be moved to the
full limit of travel and verified that sufficient clearance exists prior to beginning installation. Most aircraft
instrument panels will already have existing radio mounting cutouts. If the location you have selected
requires that a mounting hole be cut, refer to Figure 12: Panel Cut Out on Page 18 for the mounting
template. Mark and cut the mounting holes as required.

Position the unit’s mounting tray in its upright position, and from the rear of the panel. With the unit held in
place, insert the two supplied 6-32 X 1/2” countersunk screws VPN 501053 from the front and tighten as
appropriate. The installing agency must fabricate and attach rear support brackets to the aircraft structure
behind instrument panel as appropriate to support the rear of the NAV 2000. Then, attach these brackets to
the provided attachment points on the rear of the unit with the supplied 6-32 1/4" truss head screws VPN
501063.

2.4.2 Antennas
One antenna is required for the NAV 2000 installation. A standard VOR/Localizer/Glide Slope antenna can
be used with the unit such as a COMANT CI-157 or equivalent. The most common location for the antenna
is on top of the vertical stabilizer. The VOR/Localizer/Glide Slope antenna can be coupled to the unit’s
NAV-in port directly.

2.4.3 Audio
The NAV 2000 has one navigation audio output. Although the audio output levels of the receivers are
capable of driving a standard headset directly, it is strongly recommended that these audios be coupled to a
quality audio selector panel. For complete details, refer to the interconnect wiring diagrams in Appendix B.

2.4.4 Electrical
Refer to Section 6 Wiring Diagrams for expanded information regarding electrical installation.

2.5 Configuration and Initial Testing

For this Section, refer to Appendix E for a quick checklist.

2.5.1 Initial Unit Test

Upon initial powerup, verify operation of the NAV 2000 Display and Controls.
• Verify on initial startup, the display lights and shows boot introduction
• Verify after startup that unit displays react to ambient light changes (increase/decrease brightness)
• Verify that characters are complete (not missing pixels) and clear
• Rotate all 4 rotary encoders and verify that the unit reacts to input
• Push both buttons and verify that the push reacts and unit changes accordingly

2.5.2 Configuration
Configuration of the unit following physical and electrical installation is as follows:
• Enter System Configuration (Refer to Section 3.4.1)
• Chose the installed OBS device (Refer to Section 3.4.3)
• If the OBS device is a Resolver, Calibrate the unit (Refer to Section 3.4.5)
o Check the Resolver Calibration (Refer to Section 3.4.5.1)
• Configure RS-232 operation on the connected EFIS (Refer to EFIS installation manual)
• Verify operation of the RS-232 connection.

Revision 2 Page 9 of 9
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N R E C E I V E R
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

2.6 POST INSTALLATION CHECK

2.6.1 Operational Check
Using a calibrated VOR, Localizer and Glide Slope signals, check:
• VOR System:
o NAV Valid indicator (Does the flag hide with a valid signal)
o TO/FROM Flag (OFF/TO/FROM)
o CDI (-5 degrees, 0, +5 degrees)
o Received Audio (Is the tone clear and voice understandable)
o Using a Standard VOR signal applied to the RF IN, verify minimum receive
• ILS System:
o NAV Valid indicator (Does the flag hide with a valid signal)
o Glide Slope Valid indicator (Does the flag hide with a valid signal)
o CDI (Left max, Left mid, Center, Right mid, Right max)
o VDI (Up max, Up mid, Center, Down mid, Down max)
o Received Audio (Is the tone clear and voice understandable)
o Using a Standard ILS signal applied to the RF IN, verify minimum receive of the Localizer
and Glide slope

Check the operational functions of other equipment installed in the aircraft in accordance with the
individual manufacture’s operation manuals to insure that no cross interference exists as a result of this
installation.

2.6.2 Final Inspection

Verify that the wiring is bundled away from all controls and that no part of the installation interferes with
the movement of the aircraft controls. Move all of the aircraft controls through their full range of
movement while visually verifying that the installation does not mechanically interfere with the control
movement. Verify that the wiring harnesses are properly secured to the aircraft structure in accordance with
accepted practices as described in AC 43.13 and that adequate strain relief and service loops have been
provided. Ensure that there are no kinks or sharp bends in the wire harnesses. Verify that the wire bundles
are not exposed to any sharp or abrasive surfaces. Complete log book entries, weight and balance
computations and other documentations as required.

2.7 LIMITATIONS
There are no known limitations to the operation of the NAV 2000. Instructions for Continued
Airworthiness and Return to Service Instructions can be found in Appendix C.

Revision 2 Page 10 of 10
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N R E C E I V E R
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

3 SECTION III - OPERATION

This section will provide detailed operating instructions for your new NAV 2000 Navigation Receiver.
Please read this section completely to become familiar with all of the features of the unit.

3.1 Display Functions

Active Standby
Frequency Frequency

Figure 1: NAV 2000 Displays showing Active and Standby Frequencies

3.2 User Controls

ON/OFF
Mem
Freq Swap

Volume KHz adj

MHz adj
OBS Figure 2: NAV 2000 Button Controls

The user controls consist of two sets of concentric rotary knobs. The set on the left control the volume and
select memory functions while set on the right select the standby frequency and toggle between the active
and standby. Both sets of knobs contain three parts, the inner knob (the small one) the outer knob (the large
one) and a momentary push button (the end of the small knob).

3.2.1 Turning the unit on/off

To turn the unit on, momentarily press the left hand inner knob (MEM). The unit will go through a short
initialization routine at start up and then begin operation at the same settings that were loaded at the last
power down. To turn the unit off, press and hold the left inner knob (MEM) for three seconds.

3.2.2 Setting Active and Standby Frequency

The knob functions of the right hand set are as follow; the right inner knob (kHz) will change the standby
frequency by KHz or the numbers to the right of the decimal point (108.15) in 50kHz (0.05 MHz)
increments. The left outer knob (MHz) will change the frequency by MHz or the numbers to the left of the
decimal point (108.15) in 1 MHz increments. Only the frequency in the standby position will change. The
standby frequency is displayed on the right side of the display and is identified by the letter “S” to the left
of the frequency (S108.15). To load the standby frequency in to the active position, momentarily press on
the inner right knob (SWAP). This will swap the standby frequency with the active frequency. The active
frequency is identified by the letter “A” at the left of the frequency display (A108.15).

Revision 2 Page 11 of 11
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N R E C E I V E R
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

3.2.3 Setting a Bearing

The bearing on the unit can be selected through one of four ways: Using a mechanical resolver, through
the RS-232 input, through the Large Left encoder (OBS), or through using the basic nav setting.
When working with a mechanical resolver, select the desired bearing using the OBS knob on the indicator.
For more information regarding selecting a bearing using a serial input, please see the owner’s manual that
was included with the driving device.
When the unit is set to Rs I:Ser, Non, or Res, the NAV 2000 will temporarily change the Standby
display to show the current Bearing. In the Non setting, the bearing can be adjusted directly through the
use of this encoder.
The Basic Nav setting (Rs I:Int) provides a deviation on the display where the Active frequency
normally is placed, allowing for direct selection of the active frequency, and the bearing is set through use
of the inner and outer left hand knobs (normally the volume control). In this mode the memory and volume
control are unavailable. Please see the system configuration section for more information about this mode.
NOTE: When using the Basic Nav functions the unit MUST be connected to a CDI for IFR flight the
display CDI is for reference only.

3.2.4 Changing the Volume

Rotating the inner left rotary encoder (Vol) controls the receiver’s audio volume. “VOL” will be displayed
in the standby frequency display and the volume level is indicated by the numeric value after “VOL” (e.g.
“VOL 15”). The volume level can be adjusted from 0 to 20. Normal display operation resumes after 5
seconds.

3.3 Memory
3.3.1 Selecting a Stored Memory Station
A quick push of the left hand knob (MEM) enters the stored station retrieval. If no memory stations are
available, the display will show “NO MEM” and return to normal operation. Rotating the inner left hand
knob scrolls through the previously entered memory stations. In the left side (previously the active display)
the pre-programmed label will be shown, and the right side (previously the standby display) will show the
associated frequency. Once the desired frequency is displayed, a quick push of the left hand knob will
cause the selected frequency to be loaded into the Standby window and the unit will return to normal
operation. To exit without selecting a memory frequency, just wait 5 seconds without twisting any knob
and the display will return to normal, or push the right hand knob to exit instantly.

3.3.2 Entering / Editing / Deleting a Stored Memory Station

Val Avionics does not recommend entering or editing stored frequencies in flight. Doing so can be a
distraction to the pilot.

3.3.3 Selecting a stored frequency to be created / edited /deleted

By pushing both left (MEM) and right (SWAP) buttons, the unit will enter the stored frequency edit select
mode. If there are no frequencies entered, or the unit is selecting an open memory slot, the unit will show
no text in the active window, and the standby will display “<EMPTY>”. To add a new frequency, rotate the
inner left knob (VOL) until the display shows “<EMPTY>”. To edit a currently existing frequency, rotate
the inner left knob (VOL) to the frequency / station label that is to be edited.

3.3.4 Creating / Editing a stored frequency

Depress the left hand button (MEM) to enter the edit mode, which is characterized by a blinking cursor at
the leftmost position of the label text. By rotating the left inner knob (VOL), a new character can be
selected for the memory location. By rotating the left outer knob (OBS), the position of the cursor can be
changed. Once the label has been entered, rotating the right knobs (kHz & MHz) will allow for the
frequency to be selected. When the data is entered as desired, pressing the left hand button (MEM) will

Revision 2 Page 12 of 12
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N R E C E I V E R
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

exit the edit mode and return to the previous state. If desired, additional frequencies can be edited or added
by repeating the above steps.

3.3.5 Deleting a Stored frequency

Once the undesired frequency has been selected (see 3.3.3), press the right hand knob. A confirmation will
appear in the Standby window, rotate the left hand inner knob (VOL) to select “Y”, and press the right
hand knob (SWAP) to confirm. This deletes the stored information.

3.3.6 Exiting the stored frequency editing functions

To exit and return to normal operation, pressing both buttons (VOL & SWAP) will return to normal
operation.

3.4 System Configuration

When configuring the initial settings of the NAV 2000, please refer to Section 9 - Appendix E, which
contains the checkout log for setting up the unit.

3.4.1 Accessing Setup Functions Config

Setting
During startup, press and hold both
buttons simultaneously to assess
Config
the unit’s setup mode; The Option
Active frequency remains on the
Left display, while the right display will
show Rs I:xxx. To select each Figure 3: NAV 2000 in Configuration Mode
individual setting, rotate the left outer
knob (OBS) until the desired configuration setting is displayed. To select an option from the configuration
setting, rotate the left inner knob (VOL). To exit this mode and resume normal operation, press both
buttons simultaneously (MEM & SWAP).

3.4.2 Configuration Options

The available Configuration settings are as follows:
Rs I: Resolver Input selection: This allows selection of the OBS data input.
Rs T: Resolver Test: This function shows the current selected OBS from either the mechanical
resolver or the Serial port as selected from Rs I.
RsCl: Resolver Calibration: Allows for the calibration of a mechanical resolver.
SrMd: Serial Mode: Allows for configuration as a standalone unit or slaved to a COM 2000 to
fully emulate a Garmin SL-30.
VORC: VOR Calibrate: Allows for front panel calibration of the VOR system to the currently
displayed frequency.

3.4.3 OBS/Resolver Selection (Rs I)

Selecting the OBS input to the unit using the configuration pages has 4 options:

Ser: Serial input: The unit accepts the OBS over the RS-232 input and changes the deviation
outputs accordingly with the inputted data. The autopilot outputs and serial command 21
will flag if there is no serial OBS data provided every 5 seconds.
Res: Mechanical Resolver: The unit uses the analog resolver inputs to determine the OBS and
changes the deviation outputs accordingly.
Int: Internal OBS: The NAV 2000 changes its display, eliminating the standby frequency and
memory access to allow for direct input of the OBS. In this mode, the Volume knob
becomes the OBS Control, and frequency input is directly inputted through the frequency
knobs (Right Hand inner and outer). The display shows a digital CDI, however this is not
to be used for IFR flight. In order to allow for IFR flight, an external CDI/VDI MUST be
attached to the unit.

Revision 2 Page 13 of 13
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N R E C E I V E R
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

Non: Internal OBS: The unit allows for adjustement of the OBS by using the Large Left encoder
(OBS) and a temporary display. This mode is recommended for EFIS units that have an
on-screen OBS display without means of changing the OBS directly. The autopilot outputs
and serial command 21 base their deviation on the internal OBS.

To select your chosen OBS input device, rotate the left inner knob (Vol).

3.4.4 Resolver Test (Rs T)

The resolver test option has no functions. In this setting, the
information following the: represents the currently received data
from the mechanical resolver. If the bearing being displayed is
incorrect, select the Resolver Calibration setting (RsCl) and Figure 4: NAV 2000 showing Resolver Test
calibrate the NAV 2000 to the attached head. In order for the unit to read the bearing
from a mechanical head, the Active frequency must be set to a VOR frequency.

3.4.5 Resolver Calibration (RsCl)

The resolver calibration option has two settings, No and Yes. When initially
selected, No will be displayed. Calibration of the NAV 2000 to the resolver is as
follows:
• Rotate the inner left knob (Vol) to “Yes”
• Push the left knob (MEM). The display will show “RsCl:150”. (See Figure 5: Analog OBS
Figure 6) indicator set to 150

• Set your Resolver head to 150°.

• Press the left knob (MEM). Wait, as this calibration
takes some time. When it completes, the display will
show “RsCl:120”. (See Figure 7) Figure 6: Resolver Cal showing 150
• Set your Resolver head to 120°.
• Press the left knob (MEM). The display will show a
radial near 75.
• Set your Resolver head to the shown radial Figure 7: Resolver Cal showing 120
• Press the left knob (MEM).
• On success, the display will show “Cal”
• If there is an error at any time, the display will show “Err” and cancel the calibration.
If the result of “Err” is received, check your wiring between the mechanical resolver and the NAV 2000. If
the calibration is canceled anytime before the Cal response is received, either restart the calibration process
or reset the unit to restore the previous configuration.
3.4.5.1 Post Calibration Check
Following a calibration of the resolver, it is recommended that the unit be checked with the internal
decoder inside the NAV 2000. Use table XX to verify proper operation of the unit.
a) With the NAV 2000 on and in the setup functions mode (See 3.4.1)
b) Select the Resolver Test (3.4.4)
c) Set the OBS to 0°.
d) Verify on the NAV 2000 display e.g. “A108.00 RS I:0 “
e) Record the indicated bearing on table XX
f) Repeat steps c) through e) every 30 degrees.

Revision 2 Page 14 of 14
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N R E C E I V E R
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

3.4.6 Serial Mode (SrMd)

The serial mode configures the RS-232 output to work either as
a standalone navigation unit (DIR), or as a slave to the COM
2000 to fully emulate the SL-30 (PAS). This setting has two
options, DIR and PAS. Figure 8: Serial Mode Selection
• DIR: Direct serial. The output directly connects to an
EFIS or other serial device.
• PAS: Passthru. The output connects to a COM 2000 before connecting to an EFIS or other serial
device. This option has become depreciated with new COM 2000’s

3.4.7 VOR Calibration (VORC)

The VOR Calibration allows for the user to calibrate the VOR
settings and has two options, No and Yes. When initially
selected, No will be displayed. Calibration of the NAV 2000
VOR is as follows.
Figure 9: VOR Calibration Selection
• Have a certified and calibrated VOT or VOR
calibration device available.
• Channel the unit to the selected frequency (108.00 MHz for a VOT) and verify reception (The
CDI will unflag)
• If the calibration device has a bearing select, set it to 0.
• Rotate the inner left knob (Vol) to “Yes”.
• Push the left knob (ON/OFF).
• After 1 minute, the unit will display either “Cal” indicating a successful calibration or “Err”
indicating an error.
If the result of “Err” is received, verify reception of the test frequency and operation of the antenna.

WARNING: Care must be taken when using the VORC function. This will calibrate the unit to any
received radial broadcast at the chosen frequency. As such, the unit will take any received radial and after
calibration point to 0°.

Revision 2 Page 15 of 15
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N R E C E I V E R
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

4 SECTION IV - WARRANTY AND SERVICE

4.1 LIMITED WARRANTY
The equipment delivered with this Standard Factory Warranty is manufactured by Val Avionics, Ltd. and is
guaranteed against defective materials and workmanship for one year from date of original retail purchase.
Any unit found to be defective due to material and workmanship during the warranty period will be
repaired or replaced at the sole discretion of Val Avionics Ltd.

Val Avionics, LTD liability under this warranty is limited to servicing, repairing or adjusting any
equipment returned prepaid to the Val Avionics’ factory by express written or verbal authorization for that
purpose and to repair or replace defective parts thereof.

If, upon examination, it is determined that a malfunction has been caused by misuse of the equipment,
installation or operation not in accordance with factory instructions, accident or negligent damage,
alterations of any manner, and repair by other than the factory, the repairs will not be covered under the
warranty. In such cases, an estimate will be submitted for approval before repair is initiated. In most cases,
Val avionics, Ltd. will provide 72-hour turn around on its warranty and repair service. We recommend that
contact be made with the FACTORY CUSTOMER SERVICE DEPARTMENT prior to any unit return and
obtain RETURN AUTHORIZATION AND INSTRUCTIONS. This will provide proper control and
expedite service.

Val Avionics, Ltd. reserves the right of continuous product development without obligation to install
changes in previously manufactured products.

Installation of Val Avionics, Ltd. products must conform to methods acceptable by the Federal Aviation
Administration as described in the appropriate Federal Aviation Regulations (FAR’s) and Advisory
Circulars (AC’s).

To ensure proper warranty registration, type or print clearly the application information on the enclosed
PRODUCTS WARRANTY REGISTRATION FORM and return to Val Avionics, Ltd.

4.2 SERVICE

Repair service for the NAV 2000 Navigation Receiver is available at our manufacturing facility. Units in
need of servicing should be returned prepaid to Val Avionics Ltd at the following addresses.

Val Avionics
2950 Pringle Road S.E.
Salem, OR 97302

Revision 2 Page 16 of 16
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N R E C E I V E R
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

5 Appendix A – INSTALLATION DRAWINGS AND

CONNECTOR LAYOUT

Figure 10: Physical Dimensions

Revision 2 Page 17 of 17
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N R E C E I V E R
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

Figure 11: P1 Connector Pin Out

(Drawing Not to Scale)

Figure 12: Panel Cut Out

Figure 13: Mounting Tray Assembly Exploded View

Revision 2 Page 18 of 18
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N R E C E I V E R
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

Table 4: Rear Connector Pin Functions

Pin Functoin I/O

1 Main Power Input
2 Airframe Ground
3 Serial Ground
4 RS-232 Input Input
5 RS-232 Output Output
6 Reserved
7 OBS_D (COS) Input
8 Reserved Input
9 Reserved
10 CDI +Flag Output
11 + From Output
12 + To Output
13 CDI +Right Output
14 CDI + Left Output
15 Backcourse Output
16 OBS_F (SINE) Input
17 Reserved
18 Reserved
19 Composite Output Output
20 Audio Ground
21 Reserved
22 Reserved
23 Audio Output Output
24 OBS_H (Reference) Output
25 OBS_C Output
26 OBS_E Input
27 Reserved
28 VDI +Flag Output
29 CDI -Flag Output
30 VDI +Up Output
31 VDI + Down Output
32 VDI - Flag Output
33 ILS Energize Output
34 OBS_G Output
35 Reserved
36 Reserved
37 Ground (composite)

Revision 2 Page 19 of 19
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N R E C E I V E R
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

6 Appendix B – WIRING DIAGRAMS

Figure 14: NAV 2000 Basic Wiring Diagram

Figure 15: NAV 2000 to Nav Indicator

Figure 16: NAV 2000 to Nav Converter

Revision 2 Page 20 of 20
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N S Y S T E M
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

This Page Intentionally

Left Blank

Revision 2 Page 21 of 21
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N S Y S T E M
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

7 Appendix C – INSTRUCTIONS FOR CONTINUED

AIRWORTHINESS

7.1 MAINTENANCE INSTRUCTIONS

Maintenance of the NAV 2000 Navigation Receiver is on condition only. No periodic maintenance is
required. VOR calibration, in accordance with 14 CFR 91.171, is required to be checked every 30 days.
If unit is found to be out of calibration, see section 3.4.7 for calibrating the VOR. If the unit is removed for
service, upon re-installation perform Post Installation check as described in section 2.4 of this manual.

Revision 2 Page 22 of 22
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N S Y S T E M
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

8 Appendix D – RS-232 Instruction Listing

This appendix includes the interface specifications for the RS-232 serial port. The RS-232 port can
be used to input active and standby frequencies as well as using an external serial resolver such as an
EFIS system. The interface format conforms to NMEA 0183 message format specifications.

8.1 Input Commands

The following input command messages are supported:
• Input VOR frequency data from a remote source
• Input Localizer frequency data from a remote source
• Request data output
• Set active VOR/LOC frequency data from a remote source
• Set standby VOR/LOC frequency data from a remote source
• Set Omni-Bering Select (OBS) value from remote source

8.2 Output Messages

The NAV 2000 output messages include:
• Reset status
• CDI, GSI, and flags
• Decoded OBS setting
• Radial from active VOR
• Communications Error
• NAV Receiver status
• NAV audio mode
• NAV microcontroller software version

8.3 Data Format

The data format for serial communication is:
• Baud rate 9600
• Data bits 8
• Stop bits 1
• Parity none

8.4 Default Message Output

At system start when the NAV 2000 is configured to operate in normal mode, the following
messages will be configured for output and the specified rates:
• CDI, VDI, and Flags at 10 Hz (high rate)
• Decoded OBS Setting at 10 Hz (high rate)
• Radial from Active VOR at 10 Hz (high rate)
• NAV Receiver status at 1 Hz (low rate)
These default rates can be changed by using the Request Data Output message.

Revision 2 Page 23 of 23
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N S Y S T E M
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

8.5 Message Formats

All messages will conform to the NMEA 0183 proprietary message format as follows. All
characters will be standard ASCII characters. No binary data characters will be used.

“$”.....................................Start of message character, ASCII “$” (024h)

“P”.....................................Proprietary message identifier
“MRR” ..............................II Morrow company identifier
c ........................................Message class identifier. Used to identify a message as either
a COMM of VHF NAV message. Those message types,
which are also supported by the VAL COM 2000 VHF
Transceiver, will use the “C” identifier to allow the NAV 2000
to accept COMM radio commands from existing products.
All other messages will use the “V” identifier to indicate that
they relate to a VHF NAV receiver.
nn ......................................Message identifier, two-digit number in ASCII characters.
d…d ..................................Message data characters defined for each message.
chksum ..............................Message checksum, including message identifier through data
characters. The two-digit checksum is generated by adding all
values of valid characters together, ignoring carry (if any).
This value is converted into two encoded hex1 characters (30h-
3Fh).
<CR>.................................ASCII carriage return (0Dh)
<LF> .................................ASCII line feed (0Ah)

The maximum message length, including the start of message character (“$”) and the end of
message <CR><LF> sequence, is 25 bytes.

This message format is the same as is used in the VAL COM 2000 VHF Transceiver. The NAV
2000 will be able to accept all messages intended for a COM 2000 without generating a serial
communications error. It will forward all of those messages.

1
Encoded Hex: each character consists of 4 bits of data placed in the low order nibble +30h. For example,
the 8-bit value of 5Fh would be encoded as two characters with values of 35h and 3Fh, which map to the
ASCII characters “5” and “?” respectively.

Revision 2 Page 24 of 24
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N S Y S T E M
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

8.6 Message Definitions

Input Messages

REQUEST DATA OUTPUT

This input is used to request an output message to be sent by the NAV 200.

Message format:
“V” ...............................Message class. This is a VHF NAV message.
“24” ..............................Message identifier.
ii ....................................Output identifier of requested message, two ASCII characters.
dd...................................Message data, two encoded hex2 characters (30h-3Fh), used for specific
output request. Set to “00” if not needed. These characters are used for
such items as selecting a specific EEPROM address to output.
A....................................Request type: (ASCII) “0”= output repeatedly at low speed (1 Hz); “H” =
output repeatedly at high speed (10 Hz).

ii Output Dd Data Description a

“20” Reset Status “00” “0”
“21” CDI, GSI, and Flags “00” “0”, “L”, “H”
“22” Decoded OBS Setting “00” “0”, “L”, “H”
“23” Radial from Active VOR “00” “0”, “L”
“28” Receiver Status “00” “0”
“30” NAV Microntroller Software Version “00” “0”
“32” ADC Data Output cc ADC channel: “00” “0”
to “08”
“35” Comm Transceiver Status “00” “0”
“36” Comm Software Version “00” “0”
Table 5 - Data Output Requests

Example messages:

$PMRRV242100L<chksm><CR><LF>
Request periodic output of CDI, GSI, and related flags at low (1Hz) rate.

$PMRRV2432050<chksm><CR><LF>
Request a single output of ADC data from channel 5.

SET ACTIVE VOR/LOC FREQUENCY AND RECEIVER FUNCTION

This message is used to set the standby VOR or Localizer frequency as well as the receiver
operating function. The NAV 2000 can detect if the supplied frequency corresponds to a VOR or a
Localizer channel, so this command will work for both types of NAV aids.

2
Encoded Hex: each character consists of 4 bits of data placed in the low order nibble +30h. For example,
the 8-bit value of 5Fh would be encoded as two characters with values of 35h and 3Fh, which map to the
ASCII characters “5” and “?” respectively.

Revision 2 Page 25 of 25
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N S Y S T E M
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

Message format:
$PMRV27E4N<chksm><CR><CR><LF>

This example command would set the active VOR frequency to 117.100 MHz. This can be
interpreted by noting that the ASCII ‘E’ corresponds with 45h, + 30h = 75h, converted to decimal
equals 117 for the MHz portion of the command. The kHz portion converts ASCII ‘4’ to 34h, -
30h = 4h, x 25 kHz steps = 100 kHz. This command would also set the receiver function to
normal, leaving the standby channel inactive.

Note: The NAV 2000 will check input frequencies for validity. An RS-232 serial error message
output will be generated if the frequency is invalid.

SET STANDBY VOR/LOC FREQUENCY AND RECEIVER FUNCTION

This message is used to set the standby VOR or Localizer frequency as well as the receiver
operating function. The NAV 2000 can detect if the supplied frequency corresponds to a VOR or a
Localizer channel, so this command will work for both types of NAV aids.

Message format:
“V”………..Message class. This is a VHF NAV message.
“28”………Message identifier.
mk………..Standby VOR/LOC frequency:
m = desired frequency in MHz in hexadecimal, where m = desired
frequency – 30h, with desired frequency in range of 108 to 117 MHz.
k = desired frequency in kHz, where k = (desired frequency / 25 kHz) +
30h, desired frequency in range of 000 to 975 kHz in 50 kHz steps, or the
even numbers from 30h to 56h.
a………….Receiver function: N = normal, 0 = unchanged.

Example message:
$PMRRV28?PN<chksm><CR><LF>

This example command would set the standby VOR frequency to 111.800 MHz. This is
interpreted by noting that the ASCII ‘?’ corresponds with 3Fh, + 30h = 7Bh, converted to decimal
equals 111 for the MHz portion. The kHz portion converts ASCII ‘P’ to 50h, -30h, -30h yields
20h, x 25 kHz steps = 800 kHz portion. This command would also set the receiver function to
normal, so the receiver would receive only the active VOR channel.

Note: The NAV 2000 will check input frequencies for validity. An RS-232 serial message output
will be generated if the frequency is invalid.

SET STANDBY COM FREQUENCY AND TRANSRECEIVER FUNCTION

This message is issued to set the standby COM frequency.

Message format:
“V”..................... Message class. This is a VHF NAV message.
“29”.................... Message identifier.
Mk...................... Standby COM frequency:
m = desired frequency in MHz in hexadecimal, where m = desired frequency - 30h, with desired
frequency in range of 118 to 136 MHz, or 162 MHz.
k = desired frequency in kHz, where k = (desired frequency / 25 kHz) + 30h, with desired
frequency in range of 000 to 975 kHz in 25 kHz steps.

Revision 2 Page 26 of 26
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N S Y S T E M
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

a……………..Transceiver function: N = normal, 0 = unchanged.

Example message:
$PMRRV29G4M<chksm><CR><LF>

This example command would set the standby VOR frequency to 119.100 MHz. This is
interpreted by noting that the ASCII ‘G’ corresponds with 47h, + 30h = 77h, converted to decimal
equals 119 for the MHz portions. The kHz portion converts ASCII ‘4’ to 34h, - 30h yields 4h x 25
kHz steps = 100 kHz.

Note: The COM 2000 will check input frequencies for validity. An RS-232 serial error message
output will be generated if the frequency is invalid.

SET ACTIVE COM FREQUENCY AND TRANSCEIVER FUNCTION

This message is used to set the Active COM frequency as well as he COM transceiver function.

This message is only available in normal mode.

Message format:
“V”..................Message class. This is a VHF NAV message.
“42”.................Message identifier.
mk ...................Active COMM frequency:
m = desired frequency in MHz in hexadecimal, where m = desired
frequency – 30h, with desired frequency in range of 118 to 136MHz,
or 162MHz.
k = desired frequency in kHz, where k = (desired frequency / 25kHz
steps.)
a = Transceiver function: N = normal, 0 = unchanged.

Example message:
$PMRRV42G4N<chksm><CR><LF>

This example command would set the active VOR frequency to 119.100MHz and place the
COMM radio in Normal receive mode. This is interpreted by noting that the ASCII ‘G’
corresponds with 47h, + 30h = 77h, converted to decimal equals 119 for the MHz portion. The
KHz portion converts ASCII ‘4’ to 34h, - 30h yields 4h, x 25KHz steps = 100 kHz.

Note: The COM 2000 will check input frequencies for validity. An RS-232 serial error message
output will be generated if the frequency is invalid.

SET NAV OMNI-BEARING SELECT (OBS) VALUE

This message is used to set the OBS value used by the NAV 2000 as the elected radial for
computing the course deviation from a VOR. This message will have no effect unless the NAV
2000 is configured to use the internal OBS source, or a serial OBS source.

Message format:
“V”.................. Message class. This is a VHF NAV message.
“34”................. Message identifier.
vvv .................. OBS Value in degrees, ranging from “000” to “359”.

Example message:

Revision 2 Page 27 of 27
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N S Y S T E M
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

$PMRRV34310<chksm><CR><LF>

Set the OBS value to 310 degrees.

COM VOLUME AND SQUELCH CONTROL

This message is used to adjust the volume and squelch levels of the COM unit

Message format:
"V" ..................... Message class - VHF NAV Message
"71" .................... Message Identifier
"vs" .................... Volume level and Squelch Level:
v = Desired volume level in encoded hexadecimal, where v =
desired level + 0x30 with a range between 0 - 20, 0 being
muted
s = Desired squelch level in encoded hexadecimal, where s =
desired level + 0x30 with a range between 0 - 20, 0 being off

Example Message:

$PMRRV71;?<chksum><CR><LF>

This example command would set the volume level at 11 and the squelch at 15.

COM MIC GAIN AND SIDETONE CONTROL

This message is used to adjust the volume and squelch levels of the COM unit

Message format:
"V" ..................... Message class - VHF NAV Message
"72" .................... Message Identifier
"ms" ................... Volume level and Squelch Level:
m = Desired mic gain level in encoded hexadecimal, where m =
desired level + 0x30 with a range between 1 - 20
s = Desired sidetone level in encoded hexadecimal, where s =
desired level + 0x30 with a range between 1 - 20.

Example Message:

$PMRRV72;?<chksum><CR><LF>

This example command would set the mic gain level at 11 and the sidetone at 15.

Revision 2 Page 28 of 28
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N S Y S T E M
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

NAVIGATION VOLUME CONTROL

This message is used to adjust the volume level of the NAV unit

Message format:
"V" ..................... Message class - VHF NAV Message
"73" .................... Message Identifier
"v" ...................... Volume level:
v = Desired volume level in encoded hexadecimal, where v =
desired level + 0x30 with a range between 0 - 20, 0 being
muted

Example Message:

$PMRRV73;<chksum><CR><LF>

This example command would set the volume level at 11.

OUTPUT MESSAGES
RESET STATUS
This message is sent to indicate to the host that the NAV 2000 is running and ready to accept data
on the serial port. It will be sent once upon startup and when requested by the host.

Message format:
“V”………..Message class. This is a VHF NAV message.\
“20”………Message identifier.

Example message:
$PMRRV20<chksm><CR><LF>

NAV 2000 is running and ready to accept serial input.

CDI, GSI, AND RELATED FLAGS

This message outputs the current values of the CDI, GSI, and their related flags. After power up
this message will be output at a 10 Hz rate.

Message format:
“V”..................... Message class. This is a VHF NAV message.
“21”.................... Message identifier.
cc........................ CDI deflection. An eight-bit value indicating the amount of deflection
of the CDI needle, represented as two encoded hex3 digits. The CDI
deflection is a twos complements signed integer in the range of –100 to
100. –100 indicates full left deflection, 0 indicates no deflection, and
100 indicates full right deflection.
gg ....................... GSI deflection. An eight-bit value indicating the amount of deflection
of the GSI needle, represented as two encoded hex3 digits. The CDI
deflection is a twos complement signed integer in the range of –100 to

3
Encoded Hex: each character consists of 4 bits of data placed in the low order nibble +30h. For example,
the 8-bit value of 5Fh would be encoded as two characters with values of 35h and 3Fh, which map to the
ASCII characters “5” and “?” respectively.

Revision 2 Page 29 of 29
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N S Y S T E M
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

100. –100 indicates full deflection upwards, 0 indicates no reflection,

and 100 indicates full deflection downwards.
ff......................... Flags. Eight bits for HNAV and VNAV related flags, represented as
two encoded hex digits.
Bit 1 (1sb) Back Course enable (1 = enabled)
Bit 2 Localizer detect (1 = using localizer)
Bit 3 FROM flag (1 = From)4
Bit 4 TO flag (1 = To)
Bit 5 GSI superflag (1 = valid)
Bit 6 GSI valid (1 = valid)\
Bit 7 NAV superflag (1 = valid)
Bit 8 (msb) NAV valid (1 = valid)

Example message:
$PMRRV21817??:<chksm><CR><LF>

This message indicates a full left CDI deflection (-127), a full up GSI deflection (127), both the
GSI and NAV flags/superflags are valid, TO flag set, FROM flag not set, using a localizer, with
no back course enable.

DECODED OBS SETTING

This message outputs the current OBS setting, which may be read from an external resolver or
from user input to the front panel. After power up this message will be sent at a 10 Hz rate.

Message format:
“V”..................... Message class. This is a VHF NAV message.
“22”.................... Message identifier.
v ......................... Valid flag. “0” = OBS invalid/not present, “V” = OBS setting is valid.
ddd ..................... Three digit OBS setting, in degrees. Values are in the range of “000” to
“359”.

Example message:
$PMRRV22V170<chksm><CR><LF>

A valid OBS setting of 170 degrees.

RADIAL FROM ACTIVE VOR

This message outputs the current bearing from the active VOR station. This message will be
output even when a localizer is being tracked by the NAV receiver. In this case, the bearing will
be marked as invalid. After power up this message will be sent at a 10 Hz rate.

Message format:
“V”..................... Message class. This is a VHF NAV message.
“23”.................... Message identifier.
v ......................... Valid flag. “0” = bearing not valid, “V” = bearing is valid.
dddf .................... Bearing to a resolution of 1/10th of a degree. ddd = three digit bearing
in degrees, ranging from “000” to “359”. f = 1/10th of a degree.
Example message:
$PMRRV23V1654<chksm><CR><LF>

A valid bearing of 165.4 degrees FROM the active VOR station.

4
The TO and From flag can not both be 1, indicating that they are both valid. They can both be zero,
indicating that neither is valid. This situation will occur whenever the receiver determines that it is within
the “cone of confusion” directly over the VOR, or when no signal is being received.

Revision 2 Page 30 of 30
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N S Y S T E M
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

COMMUNICATIONS ERROR
This message is used to indicate a communication error.

Message format:
“V”..................... Message class. This is a VHF NAV message.
“27”.................... Message identifier.
e ......................... Error code: (ASCII)
“0” = input message checksum error.
“1” = unknown message.
“2” = error or mismatch in message data.

Example message:
$PMRRV271<chksm><CR><LF>

Received an unknown message.

NAV RECEIVER STATUS

This message is used to output the current status of the NAV receiver. It will be output upon
request or whenever the status changes.

Message format:
“V”..................... Message class. This is a VHF NAV message
“28”.................... Message identifier
mk ...................... Standby NAV frequency: m = MHz, where m + 30h = desired MHz
frequency in the range of 108 to 117 MHz. k= (desired frequency / 25
kHz) + 30h, with desired frequency in range of 000 to 975 kHz in 50
kHz steps.
s.......................... Status: “N” = Normal mode, “M” = Monitor mode

Example message:

$PMRRV28E4?PM<chksm><CR><LF>

Active NAV frequency is 117.100 MHz, Standby NAV frequency is 111.800 MHz, receiver is in
monitor mode.

NAV MICROCONTROLLER SOFTWARE VERSION

This message is used to output the version string for the NAV microcontroller software.

Message format:
“V”..................... Message class. This is a VHF NAV message.
“30”.................... Message identifier.
vvvv ................... Software version in ASCII
e ......................... Engineering version flag:
“R” = Released version.
“E” = Engineering version.

Example message:
$PMRRV300103E<chksm><CR><LF>

NAV Microcontroller software is version 1.03. It is an engineering version.

COM TRANSCEIVER STATUS

This message outputs the result of a specific system test.

Message format:

Revision 2 Page 31 of 31
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N S Y S T E M
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

“V”..................... Message class. This is a VHF NAV message.

“35”.................... Message identifier.
mk ...................... Active frequency: m = MHz, where m = desired MHz frequency – 30h,
ranging from 118 to 136 MHz, 162 (i.e., 76h to 88h, A2h); k = (kHz
offset / 25 kHz) + 30h, ranging from 000 to 975 kHz steps.
mk ...................... Standby frequency: m = MHz, where m = desired MHz frequency –
30h, ranging from 118 to 136 MHz, 162 (i.e., 76h to 88h, A2h); k =
(kHz offset / 25 kHz) + 30h, ranging from 000 to 975 kHz steps.
a ......................... Transceiver status:
R = Normal receive
T = Transmit enabled
S = Stuck mic
F = Comm failure
s.......................... Squelch test setting: (ASCII) 0 = automatic; 1 = test

Example message:
$PMRRV35G4LFR0<chksm><LF>

Active frequency is 119.100 MHz, the standby frequency is 124.550 MHz, receiver function,
squelch is automatic.

COM SOFTWARE VERSION

This message is used to output the version string for the VHF COM receiver software.

Message format:
“V”..................... Message class. This is a VHF NAV message.
“36”.................... Message identifier.
vvvv ................... Software version in ASCII

Example message:
$PMRRV300103<chksm><CR><LF>

COM software is version 1.03.

Revision 2 Page 32 of 32
Oct. 2014
 V A L A V I O N I C S L T D
N A V 2 0 0 0 N A V I G A T I O N S Y S T E M
I N S T A L L A T I O N A N D O P E R A T O R ’ S M A N U A L

9 Appendix E – Installation Checkout Log

Configuration Information: Date___/___/____
NAV 2000 VHF/UHF Receiver Serial#_____________ By:____________

Initial Checkout and Setup:

[ ] Resolver [ ] Serial [ ] Internal [ ] None
[ ] Display Test (Characters are Complete and Clear, Display brightens and dims with
ambient light)
[ ] Control Test (Knobs turn, display responds, pushbuttons operate)
[ ] Calibration (Resolver)
[ ] Resolver Calibration Test (See Below)
[ ] RS-232 inputs/outputs checked (if connected)

Functional Test:
VOR: ILS:
[ ] NAV Valid flag [ ] Valid Flags (NAV/GS)
[ ] TO/FROM flag (OFF, TO, FROM) [ ] Left/Right (Left, Center, Right)
[ ] CDI (-5, Center, +5) [ ] Up/Down (Up, Center, Down)
[ ] Received Audio [ ] Received Audio
_____VOR Minimum Receive _____LOC Min Receive
_____GS Min Receive

Resolver Calibration Test (Expanded): Resolver Type:__________________

OBS Rs T OBS Rs T
0 180
30 210
60 240
90 270
120 300
150 330

Comments:

Revision 2 Page 33 of 33
Oct. 2014