www.easylaser.

com
E950

Bore alignment
Straightness measurement of bore and bearing journals

E950
STRAIGHTNESS THE EASY WAY
RELIABILITY AND PRECISION
Easy-Laser® E950 makes the control and ad-
justment work of bearings easier thanks to
the wireless detector unit and measurement
programs that guides you through the meas-
urement process. All of the parts included in
the systems are designed and built for even
the most demanding workplace and for
easy setup on any machinery. The versatile
design solves the straightness measurement
problems quickly and with precision for any
kind of application. Objects up to 40 m [132
feet] can be measured. The detector reads A visible red laserbeam is the reference to which the straightness of
measurement values with a resolution of the bores is measured. Compared to older methods, e.g. piano wire,
0.001 mm [0.05 mils]. the work is done much faster, easier and more accurately.
The system comes in four versions:
• Easy-Laser® E950-A
• Easy-Laser® E950-B
• Easy-Laser® E950-C
• Easy-Laser® E950-D
Please see last page for more information.

A B C

1. You set the number of measurement points and 2. The graphics shows the detector direction. Mark- 3. “Live” adjustment of the measurement object.
the distance between them in advance, or as the ings on the circle shows active measurement point. Vertical and horizontal value for the object (B).
measurement continues. The distances can be Measurement value, and angular position for the Markings on the circle shows zone for adjustment
equal or individual. detector (A). with live values (C).

VERSATILE PROGRAMS
The straightness programs of system E950 A B C D E F G
are very versatile, and let you work in the
way that suits every job best. You can add,
remove and remeasure measurement points The measurement program includes many different methods for straightness measurement:
at any time during the measurement. Up to A: 1-point measurement, B: 2-point measurement (Note: not available in the USA), C: 4-point meas-
999 points can be handled by the program. urement, D: Multipoint measurement (also ovality measurement), E: 3-point measurement, F: 3-point
You can include both full bores and half measurement with arbitrary angles, G: Multipoint measurement
bores in any possible combination in one
measurement, the program will calculate
the correct centre line in all cases.

It’s easy to add measurement points anywhere on the object in an existing measurement. The follow-
ing points will be renumbered automatically. If you remove a point the following will be renumbered
according to the same principle. If you remeasure a point, the old values will be saved in a history
data base for possible later comparison. All this you can do at any time during the measurement!
 A B C D E

THE MEASUREMENT RESULT

Thanks to the large colour display with
clear graphs and measurement data you
can evaluate the result directly on site.
Any point can be set as reference and you
can set an offset to which the centre line
will be recalculated. You can also calculate
waviness (short and long) and best-fit for
the points. If you want, the result can also
be checked against a tolerance value. The
measurement system takes care of all these
complicated calculations for you. Result display with statistics to the left (A) and table The result can also be shown as a graph (sharp or
with values to the right (B). The reference points are interpolated). You can zoom in or show the whole
clearly marked (C). graph. Horizontal values (D) and vertical values (E).

F G H I

You can quickly change what the graph shows (G) The result displayed as “Best fit around 0” (H), and By using the Multipoint method you can get a clear
for different calculation settings, for example Best with sharp graph. view of possible bore ovality (I).
fit and Waviness as shown here (F).

DOCUMENTATION
SAVE TO USB MEMORY CONNECT TO YOUR COMPUTER EASYLINK™ PC SOFTWARE
You can easily save desired measurements The display unit is connected to the comput- With the EasyLink™ database program you
on your USB memory. This enables you to er via the USB port. It then appears on the can save and organise all your measurements
take it to your computer to print reports desktop as a “Mass Storage Device” which in one place, produce reports with both data
whilst leaving the measurement system in you can easily transfer files to and from. and images and export to your maintenance
place to continue measuring. systems. You can customise what your Excel
CREATE A PDF REPORT DIRECTLY reports should look like and what data should
SAVING IN THE BUILT-IN MEMORY When measurement is complete it is pos- be visible and where it should be positioned.
You can, of course, save all measurements in sible to generate a PDF report containing The program has a clear folder structure,
the display unit’s internal memory. You can graphs and measurement data directly in the where you drag and drop files from the
then open an old measurement and remeas- measurement system’s display unit. All the display unit to the database. Create your
ure those points you adjusted. information about the measurement object own structure with folders for manufacturer,
is documented, and you can add your com- department or machine type for example. The
CONNECT TO PRINTER pany’s logo and address details if you so wish. database can also be located on a common
Connect a thermal printer (accessory) and server and shared with other users. For extra
print locally. Good for example when you safety you can use EasyLink™ to make backups
want to see the valuesbefore and after ad- of what you have saved in the display unit.
justment, or want to leave a documentation
of the measurement on site.
THE PARTS OF THE SYSTEM
DISPLAY UNIT VALUES PROGRAM
The display unit for the E series enables you All our measurement systems come with
to work more efficiently and for longer than the universal Values program. It works like
ever before thanks to several innovative digital dial indicators. With this, you can, in
solutions. It is also ergonomically designed principle, measure any type of geometry.
with easy-to-grip rubber cladding and ro- Many Easy-Laser® users therefore end up
bust construction. using the measurement system in many
more places in their operation, than they
PERSONAL SETTINGS first intended!
You can create a user profile where you can
A B C D save your personal settings. You can also UPGRADING
A. Two Enter buttons, for left and right- have different settings for different types of If you wish to expand functionality in the fu-
handed users measurements, and save them as Favorites, ture, the software in the display unit can be
B. Large, easy to read colour display for quick access from the main menu. upgraded via the internet or by connecting a
C. Proper buttons for clear feedback USB memory containing the new software.
D. Thin profile gives a perfect grip for your hands LANGUAGE SELECTION
You can choose the language you want to
appear on the screen: English, German,
French, Spanish, Portuguese, Swedish, Finn-
ish, Russian, Polish, Dutch, Italian, Japanese,
Korean and Chinese are available.
E F G H I J

E. Robust, rubber coated design ERGONOMIC

F. Connection for charger The display unit has a thin, easy-to-grip and
G. USB A rubber coated profile that ensures a secure
H. USB B
grip. It has large well-spaced buttons that
I. Easy-Laser® measurement equipment
give clear feedback when pushed. In addi-
J. Mounting for shoulder strap
Note: Dust and splash guards for connectors tion, the two Enter buttons make the system
removed on picture. suitable for both right and left-handed users.
The display screen has clear graphics that
guide you through the measurement process.

E950-A DETECTOR E7
E950-B Detector E7 connects to the display unit via system knows exactly how the detector is
E950-D
cable or wireless. The unit for wireless com- positioned. It has a large 20 mm [0.78" sq] 2
A munication is easily inserted into one of the axis detector (PSD for the greatest accuracy).
B
connectors on the detector. The substantial
C and rigid design guarantees stable measure-
A. Well protected connectors ment values and reliable alignment with the
B. PSD (2 axis) greatest precision in even the toughest of
C. Wireless unit environments. The detector is also water and
dust proof to classes IP66 and IP67.
With built-in electronic inclinometer the

A E950-C DETECTOR E9
The E9 detector connects to the display unit next page). The detector is water and dust
B via cable or wireless (built-in). It is manufac- proof to class IP67. With built-in electronic
C
tured from a solid aluminium billet for the inclinometer the system knows exactly how
highest rigidity and measurement stabil- the detector is positioned. It has a large 20
ity even in the toughest of environments. mm [0.78" sq] 2 axis detector (PSD for the
Threads on both ends makes the detector greatest accuracy).
A. Built-in wireless unit very versatile when mounting it for different
B. Threads on both ends (4+4) applications. Rod adapter is included (see
C. PSD (2 axis)
LASER TRANSMITTER BRACKETS E950-A/E950-C/E950-D: LASER TRANSMITTER WITH ARMS 1
The laser transmitter's rigid design assures Magnet attachment
highest measurement accuracy. The bracket Support pin
comes in two different versions. Adjustable arms
1: One has three sets of adjustable arms with Offset hub
magnets to fit different diameters. Laser aperture
2: The other spans over the sterntube with Alternative mounting.
a bracket with two or three magnet bases. All three arms can be mounted
Fine adjustment of the laser beam in hori- downwards for half bores.
zontal and vertical direction is made very
Alternative mounting. Laser transmitter mounted
easy with the offset hub.
to point from e.g. fly wheel or shaft end.

E950-B: LASER TRANSMITTER WITH BEAM BRACKET 2

Magnet base

Offset hub
Laser transmitter
Laser beam angle adjustment
[Scale X] Vertical support beam mounted Mounting threads for
for large diameters vertical support beam.

DETECTOR BRACKETS E950-A/E950-C: 1

SLIDE BRACKETS (3 SIZES)
The detector bracket comes in three ver-
sions/sets depending on system.
1: Set of three slide brackets with extend-
able rods for different bore diameters.
2: Bracket with magnet bases. Comes with
extension beams for large diameters and
The magnetic feet holds Extendable rods
extension rods for the measuring probe.
The detector is rotated and moved with the the bracket perfectly in any
position around the bore
detector slide.
Magnetic feet
3: Slide bracket with a width of 25 mm [Scale X]
[0.99"]. Allows for measurement of bores
down to diameter 80 mm [3.15"] when used
with detector E9. This set also includes the E950-B/E950-D: SELF CENTERING BRACKET 2
brackets of set 1. Extendable aluminium beam
Detector slide

Extendable rods

Magnet base

Measuring probe
[Scale X]

E950-C: SLIDE BRACKET WIDTH 25 MM 3

Extendable rods
Slidable target
Rod adapter
Magnetic feet
Positioning guide
Min. 25 mm [0.99"]
[Scale X] [Scale 2X]
EXPANDABILITY / ACCESSORIES
2

LASER TRANSMITTER D22

Laser transmitter D22 can be used to measure
flatness, straightness, squareness and parallel-
1
ism. For example flatness of parting surfaces. The
laser beam can sweep 360° with a measurement
distance of up to 40 metres [130'] in radius. The
laser beam can be angled 90° to the sweep, within Option 1: the laser beam is used for a 360° sweep.
0.005mm/m [0.005mils/INCH]. Part No. 12-0022 Option 2: the laser beam is angled at 90° to the sweep.

LASER TRANSMITTER E30 LONG RANGE SHAFT ALIGNMENT MEASURING UNITS

This transmitter makes it possible to measure Align shafts and couplings with these com-
straightness on very long distances. Up to approxi- bined laser-/detector units that are mounted
mately 100 m [328'] with a 20 mm PSD (like in the on each side of the coupling. The shaft align-
E7 and E9), and >200 m [656'] with a 30 mm PSD. ment software is included as standard in the
Offset hub and arms also needed. system. Add the S- and M-units, V-brackets
with rods and chains, as well as cables or wire-
less units.

LASER TRANSMITTER D25

For straightness measurement up to 40 m [130'],
and measurement of parallelism between two or
more shafts in gearboxes. Can also be used for
rudder bearings where the axial surface is the
reference. The laser beam can be angled 90° to the
centre line. Part No. 12-0706

ADJUSTABLE MAGNET MAGNETIC BRACKET EXTENSION ARMS AXIAL EXTENSION ARMS

Adjustable 0–14mm [0–0.55"] With three super magnets. For Extension arms 500–1000 mm Making it possible to reach the
compared to standard magnet laser transmitter D75. To use on [19.68"–39.36"]. Set for D75 with Linebore detector from the
level. Part No. 12-0990. Included shaft ends, flywheels, etc. offset hub. Part No. 12-0282 same side of the bore as the
as standard with E950-A/C/D. Part No. 12-0187 transmitter. Part No. 12-0580

EXTENSION CABLES TUBE ADAPTERS ALU EXTENSION BEAMS

5 m [16.4'], Part No. 12-0108 Adapters mainly for detector 0.5 m [19.68"], Part No.03-0769
10 m [32.8'], Part No. 12-0180 E9 and used e.g. for extruder 0.6 m [23.62"], Part No.03-0770
measurements. 1.1 m [43.31"], Part No.03-0771
Part No. 01-0777
TECHNICAL DATA
System Slide bracket width 25 mm, for E9 (included in system E950-C)
Relative humidity 10–95% Measurable bore diameters B 80–250 mm [3.15"–9.84"]
E950-A: Weight 14.0 kg [30.8 lbs] (complete system) Measurable bore width Min. 25 mm [0.99"]
E950-A: Carrying case WxHxD: 550x450x210 mm [21.6x17.7x8.3"] Material Anodized aluminium
E950-B: Weight 27.0 kg [59.5 lbs] (complete system) Dimensions WxHxD: 79x57x57 mm [3.11x2.24x2.24"]
E950-B: Carrying case WxHxD: 1220x460x170 mm [48.0x18.1x6.7"] Weight 204 g [7.2 oz]
E950-C: Weight 14.3 kg [31.5 lbs] (complete system)
E950-C: Carrying case WxHxD: 550x450x210 mm [21.6x17.7x8.3"] Rods
E950-D: Weight 18.3 kg [40.3 lbs] (complete system) Length (extendable) 30/60/120/240 mm [1.18"/2.36"/4.72"/9.44"]
E950-D: Carrying case WxHxD: 550x450x210 mm [21.6x17.7x8.3"] Rod set A includes 2x30, 4x60, 4x120, 2x240 mm
Rod set B includes 2x30, 2x60, 2x120, 2x240 mm
Laser transmitter D75 with offset hub Rod set C includes 2x30, 4x60, 4x120, 2x240 mm
Type of laser Diode laser Rod set D includes 2x30, 2x60, 2x120, 2x240 mm
Laser wavelength 630–680 nm, visible red light
Laser Safety Class Class 2 Cables
Output < 1 mW Type With Push/Pull connectors
Beam diameter 6 mm [1/4"] at aperture System cable Length 2 m [78.7"]
Working distance 40-metre [130'] Extension system cable Length 5 m [196.8"]
Type of battery 1 x R14 (C) USB cable Length 1.8 m [70.8"]
Operating time/battery approx. 15 hours
Operating temperature 0–50 °C Display unit E51
Laser adjustment D75: 2 ways ±2° (± 35 mm/m), Hub: ±5 mm in two axes Type of display/size VGA 5.7" colour
Housing material Anodized aluminium Displayed resolution 0.001 mm / 0.05 thou
Dimensions D75 WxHxD: 60x60x120 mm [2.36x2.36x4.72"] Internal battery Heavy duty Li Ion chargeable
Dimensions D75 with Hub WxHxD: 135x135x167 mm [5.31x5.31x6.57"] Operating time Appr. 30 hours (Normal operating cycle)
Weight 2385 g [84.13 lbs] Operating temperature -10–50 °C
Connections USB A, USB B, Easy-Laser® units
Laser transmitter arm set (included in system E950-A and E950-C) Wireless communication BT Wireless Technology
Measurement diameters B 100–500 mm [3.93"–19.68"] Storage memory >100,000 measurements
Help functions Calculator, Unit converter
Laser transmitter beam bracket (included in system E950-B) Environmental protection IP Class 65
Measurement diameters B 250–1000 mm [9.84"–39.37"] Housing material PC/ABS + TPE
Up to 4000 mm with extension beams (accessories) Dimensions WxHxD: 250x175x63 [9.8x6.9x2.5"]
Magnet bases 3 pcs, holding power 800 N/each Weight (without batteries) 1030 g [2.3 lbs]

Detector E9 (included in system E950-C) Wireless connection unit (included in system E950-A, E950-B and E950-D)
Type of detector 2 axis PSD 20x20 mm [0.78" sq] Wireless communication BT Wireless Technology
Wireless communication BT Wireless Technology Operating temperature -10–50 °C
Resolution 0.001 mm [0.05 mils] Environmental protection IP Class 66 and 67
Measurement accuracy ± 1 µm ± 1% Housing material ABS
Inclinometers 0.1° resolution Dimensions 53x32x24 mm [2.1x1.2x0.9"]
Thermal sensors ± 1° C accuracy Weight 25 g [0.9 oz]
Environmental protection IP Class 67
Operating temperature -10–50 °C EasyLink™ Data base software
Internal battery Li-Ion System requirements Windows® XP, Vista, 7, 8, 10. For the export functions,
Housing material Anodized aluminium Excel 2003 or newer must be installed on the PC.
Dimensions B 45 mm, L=100 mm [B 1.77", L=3.94"]
Weight (excl. rod adapter) 180 g [6.3 oz]

Detector E7 (included in system E950-A, E950-B and E950-D)

Type of detector 2 axis PSD 20x20 mm [0.78" sq]
Resolution 0.001 mm [0.05 mils]
Measurement accuracy ± 1 µm ± 1%
Inclinometers 0.1° resolution CUSTOM DESIGN
Thermal sensors ± 1° C accuracy
Environmental protection IP Class 66 and 67
In addition to our already versatile standard system we can also
Operating temperature -10–50 °C specially adapt measurement systems to suit your needs. Using
Internal battery Li-Ion our own CNC machines we can quickly manufacture brackets
Housing material Anodized aluminium
Dimensions WxHxD: 60x60x42 mm [2.36x2.36x1.65"]
just for you. This means for example that brackets for other
Weight 186 g [6.6 oz] diameters than mentioned on this page can be manufactured
on request.
Self centering detector bracket for E7 (included in system E950-B and E950-D)
Measurement diameters B 300–1200 mm [11.81"–47.24"]
Up to 4000 mm with extension beams and rods (accessories)
Stroke 60 mm [2.36"]
Magnet bases 2 pcs, holding power 800 N/each WARRANTY AND SERVICE CONCEPT
Material Anodized aluminium The Easy-Laser® systems have evolved over
Weight 4400 g [9.7 lbs] (with magnets)
more than 25 years, through field experience in
3 YEAR WARRANTY
Slide brackets (included in system E950-A and E950-C) solving measurement and alignment prob-
Measurement diameters Small: B 140**–250 mm [5.51"–9.84"] lems. The systems come with a 3 year limited
(**For E7 with wireless unit Medium: B 200–350 mm [7.87"–13.78"]
mounted. E9: B120 mm [4.72"]) Large: B 300–500 mm [11.81"–19.68"]
warranty. The manufacturing and quality systems are ISO9001
Material Anodized aluminium approved. If an incident should occur, our service department
Dimensions, WxHxD S: 60x90x13 mm [2.36x3.54x0.51"] normally handles repairs and calibrations within seven working
M: 80x157x13 mm [3.15x6.18x0.51"]
L: 100x205x13 mm [3.94x8.07x0.51"]
days. This combination makes Easy-Laser® a reliable partner for
Weight S: 210 g [7.41 oz], M: 335 g [11.82 oz], L: 460 g [16.22 oz] your business.
 www.easylaser.com

EASY-LASER® E950-A EASY-LASER® E950-B

Mainly for diesel engines, Mainly for propeller shaft
compressors, gearboxes drive lines with sterntube.
and similar applications. Align sterntube, support
Measures bores B 140– bearings, gearbox and
engine.
500 mm [5.51"–19.68"].*
Measures bores B 300–
1000 mm [11.81"–39.37"].
You can also add the slide
A complete system contains A complete system contains
1 Laser transmitter D75
brackets from system 1 Laser transmitter D75
1 Detector E7 E950-A or E950-C to get a 1 Detector E7
1 Display unit E51 more versatile system.* 1 Display unit E51
1 Wireless unit 1 Wireless unit
1 Cable 2 m 1 Cable 2 m
1 Cable 5 m (extension) 1 Cable 5 m (extension)
1 Offset hub for D75 1 Offset hub for D75
1 Set of offset hub arms, with magnets 1 Transmitter bracket, with 3 magnet bases
1 Set of rods A 1 Set of rods B
1 Slide bracket Small, Part No. 12-0455 1 Self centering detector bracket, with 2 magnet bases
1 Slide bracket Medium, Part No. 12-0543 1 Large target
1 Slide bracket Large, Part No. 12-0510 1 Carrying case. Drop tested. Water and dust tight.
1 Magnet base
1 Large target System Easy-Laser® E950-B, Part No. 12-0677
1 Carrying case. Drop tested. Water and dust tight.

System Easy-Laser® E950-A, Part No. 12-0676

EASY-LASER® E950-C EASY-LASER® E950-D

Mainly for diesel engines, Mainly for propeller shaft
compressors, gearboxes drive lines with sterntube.
and similar applications. Align sterntube, support
One of the brackets has bearings, gearbox and
engine.
a width of 25 mm [0.99"]
Measures bores B
to fit in narrow bearing
300–1200 mm [11.81"–
journals. Measures bores
47.24"].
B 80–500 mm [3.15"– A complete system contains
You can also add the slide
A complete system contains
1 Laser transmitter D75 1 Laser transmitter D75
19.68"] as standard, and 1 Detector E9 brackets from system 1 Detector E7
down to 50 mm [2.00"] 1 Display unit E51 E950-A or E950-C to get a 1 Display unit E51
1 Cable 2 m 1 Wireless unit
with customized brackets. 1 Cable 5 m (extension) more versatile system.* 1 Cable 2 m
With additional acces- 1 Offset hub for D75 1 Cable 5 m (extension)
1 Set of offset hub arms, with magnets 1 Offset hub for D75
sories extruder machines
1 Set of rods C 1 Set of offset hub arms, with magnets
can also be measured.* 1 Rod adapter for detector, with built in target 1 Set of rods D
1 Slide bracket, width 25mm, Part No. 12-0768 1 Extension arms Linebore
1 Slide bracket Small, Part No. 12-0455 1 Self centering detector bracket, with 2 magnet bases
1 Slide bracket Medium, Part No. 12-0543 1 Large target
1 Slide bracket Large, Part No. 12-0510 1 Carrying case. Drop tested. Water and dust tight.
1 Magnet base
1 Carrying case. Drop tested. Water and dust tight. System Easy-Laser® E950-D, Part No. 12-0954

System Easy-Laser® E950-C, Part No. 12-0772

All systems contain *Note: exact measurable diameters also depends on

1 Manual 1 Battery charger (100–240 V AC) the design of the object to be measured (e.g. where
1 Measuring tape 5 m 1 Toolbox
magnets can be placed). Custom designed brackets
1 USB Memory stick with documentation 1 Shoulder strap for Display unit
1 USB Cable 1 Cleaning cloth for optics can extend the range. Ask us for more information.

Easy-Laser® is manufactured by Easy-Laser AB, Alfagatan 6, SE-431 49 Mölndal, Sweden

Tel +46 31 708 63 00, Fax +46 31 708 63 50, e-mail: [email protected], www.easylaser.com
© 2022 Easy-Laser AB. We reserve the right to make changes without prior notification.
Easy-Laser® is a registered trademark of Easy-Laser AB. Other trademarks belong to the relevant copyright holder.
050540 Rev9

Av. Los Proceres No.62, Cond. Plaza Lincoln

ISO 3 Santo Domingo, D. N. Rep. Dominicana
9001
CERTIFIED
YEAR GLOBAL Tel. 809.819.4001
WARRANTY SUPPORT
COMPANY