3/25/24, 4:02 PM SIS 2.
Water Pump - Remove (SENR1126-36)
SMCS - 1361 i05056215
Removal Procedure
PSP
202 -000A
08: 4/03/2 4FC7
NOTICE
Keep all parts clean from contaminants.
0
SEN 2:48+ 5
Contaminants may cause rapid wear and shortened component
life.
© 2 R112 08:00
024 6
NOTICE
Cat
erp
Care must be taken to ensure that fluids are contained during
illa
performance of inspection, maintenance, testing, adjusting, and
repair of the product. Be prepared to collect the fluid with
r In
suitable containers before opening any compartment or
disassembling any component containing fluids.
c.
Refer to Special Publication, PERJ1017, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain
fluids on Cat® products.
Dispose of all fluids according to local regulations and
mandates.
1. Drain the coolant from the cooling system into a suitable container for storage or disposal.
https://sis2.cat.com/#/print-preview/service/42e1bb6f-7bbd-4626-b8ca-795edcc3555c 1/5
3/25/24, 4:02 PM SIS 2.0
Illustration 1 g01053075
2. Remove bolts (1). Remove tube assembly (2).
Illustration 2 g01053077
3. Attach a suitable lifting device to water pump (4). Remove bolts (3).
Illustration 3 g01053079
4. Remove bolts (5).
https://sis2.cat.com/#/print-preview/service/42e1bb6f-7bbd-4626-b8ca-795edcc3555c 2/5
3/25/24, 4:02 PM SIS 2.0
Illustration 4 g01053081
5. Remove water pump (4). The weight of the water pump is approximately 45 kg (100 lb).
Removal Procedure (Type 2)
Table 1
Required Tools
Tool Part Number Part Description Qty
9U-7089 Tapered Cap/Plug 1
ZZ
9U-7095 Tapered Cap/Plug 1
Note: SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN PHOTOGRAPHS IN THE
REMOVAL OR THE INSTALLATION. THIS TOOLING IS SHOWN IN ORDER TO ASSIST THE
EXPERIENCED SERVICEMAN.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component
life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and
repair of the product. Be prepared to collect the fluid with
suitable containers before opening any compartment or
disassembling any component containing fluids.
Refer to Special Publication, PERJ1017, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain
fluids on Cat® products.
Dispose of all fluids according to local regulations and
mandates.
https://sis2.cat.com/#/print-preview/service/42e1bb6f-7bbd-4626-b8ca-795edcc3555c 3/5
3/25/24, 4:02 PM SIS 2.0
1. Drain the cooling system coolant. Refer to Operation and Maintenance Manual, "Cooling
System Coolant (DEAC) - Change".
Illustration 5 g01127935
2. Disconnect hose assembly (1).
3. Disconnect adapter (2) and the gasket from water pump (3).
4. Disconnect tube assembly (6) from adapter (5).
5. Remove bolts (4) in order to remove adapter (5) and the O-ring seal from water pump (3).
6. Remove bolts (7) in order to remove guard assembly (8) from the engine.
https://sis2.cat.com/#/print-preview/service/42e1bb6f-7bbd-4626-b8ca-795edcc3555c 4/5
3/25/24, 4:02 PM SIS 2.0
Illustration 6 g01127942
7. Remove bolts (9) in order to remove water pump (3) from the engine. Use two people in order
to remove water pump (3) from the engine. The weight of water pump (3) is approximately
34 kg (75 lb).
PSP-000A4FC7
2024/03/25
08:02:42+08:00
i02053499
© 2024 Caterpillar Inc.
https://sis2.cat.com/#/print-preview/service/42e1bb6f-7bbd-4626-b8ca-795edcc3555c 5/5
