3/25/24, 4:03 PM SIS 2.

Water Pump - Disassemble (SENR1126-36)

SMCS - 1361 i06811905

Disassembly Procedure (Type 3)

PSP
202 -000A
Table 1

08: 4/03/2 4FC7

Required Tools
Tool Part Number Part Description Qty
A
B
1P-0510
-
Driver Gp
0
SEN 3:11+ 5
1 inch by 4 inch steel plate
1
2

© 2 R112 08:00
C 248-3311 Holding Fixture 1
D 476-2902 Spanner Wrench 1
E 8H-0663 024 6
Bearing Puller Gp 1

Cat
erp
Start By:

a. Remove the water pump.

illa
r In
NOTICE c.
Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component

life.

https://sis2.cat.com/#/print-preview/service/9f0a57aa-e977-439f-8d40-124463f6f1de 1/8
3/25/24, 4:03 PM SIS 2.0

Illustration 1 g01036014

1. Remove plug (1) and plug (2) from bearing housing (3). Remove plug (6) from housing (5).
Remove the O-ring seals from the plugs.

2. Remove water pump filter (4) from bearing housing (3).

https://sis2.cat.com/#/print-preview/service/9f0a57aa-e977-439f-8d40-124463f6f1de 2/8
3/25/24, 4:03 PM SIS 2.0

Illustration 2 g01035264
3. Remove bolts (7) and washers. Remove bearing housing (3) from housing (5). Remove O-ring
seal (8) from bearing housing (3).

https://sis2.cat.com/#/print-preview/service/9f0a57aa-e977-439f-8d40-124463f6f1de 3/8
3/25/24, 4:03 PM SIS 2.0

Illustration 3 g01035285
4. Install Tooling (B) under impeller (9). Use a suitable press and Tooling (A) to remove the
impeller.
Note: Do not allow bearing housing (3) to fall to the floor when the impeller is removed from the
pump shaft.

https://sis2.cat.com/#/print-preview/service/9f0a57aa-e977-439f-8d40-124463f6f1de 4/8
3/25/24, 4:03 PM SIS 2.0

Illustration 4 g06095378
5. Remove socket head bolts (10). Remove retainer (11) and pump shaft (12) from bearing
housing (3).

https://sis2.cat.com/#/print-preview/service/9f0a57aa-e977-439f-8d40-124463f6f1de 5/8
3/25/24, 4:03 PM SIS 2.0

Illustration 5 g06095400
6. Install pump shaft (12) in Tooling (C). Loosen set screws (14). Use Tooling (D) to remove
bearing locknut (15) from the pump shaft.
Note: The splined end of the pump shaft is marked to indicate either RH threads or LH threads
on the pump shaft.

https://sis2.cat.com/#/print-preview/service/9f0a57aa-e977-439f-8d40-124463f6f1de 6/8
3/25/24, 4:03 PM SIS 2.0

Illustration 6 g06095401
7. Use Tooling (E) to remove bearing assembly (16) from pump shaft (12).

Illustration 7 g06095428

8. Remove seal assembly (13) and lip seal (17) from bearing housing (3).

https://sis2.cat.com/#/print-preview/service/9f0a57aa-e977-439f-8d40-124463f6f1de 7/8
3/25/24, 4:03 PM
202 000A SIS 2.0

PSP-000A4FC7
08: 4/03/2 4FC7
0
2024/03/25

SEN 3:11+ 5
08:03:02+08:00
i06811905

© 2 R112 08:00
© 2024 Caterpillar Inc.

0 6

https://sis2.cat.com/#/print-preview/service/9f0a57aa-e977-439f-8d40-124463f6f1de 8/8