HYDRAULIC ROUGH TERRAIN CRANE

SPEC. SHEET NO. GR-300E-2-00102/EX-01

GR-300EX Left hand steering

GENERAL DATA
CRANE CAPACITY 30,000 kg at 3.0 m
BOOM 4-section, 9.7 m - 31.0 m
DIMENSION
Overall length approx. 11,245 mm
Overall width approx. 2,620 mm
Overall height approx. 3,535 mm
MASS
Gross vehicle mass approx. 27,190 kg
-front axle approx. 13,650 kg
-rear axle approx. 13,540 kg
PERFORMANCE
Max. travelling speed computed 50 km/h
Gradeability(tan ) computed 78 % (at stall)
*57 %
*Machine should be operated within the limit of engine crankcase
design (30˚: Cummins QSB6.7)

CRANE SPECIFICATIONS
MODEL SINGLE TOP (AUXILIARY BOOM SHEAVE)
GR-300EX Single sheave. Mounted to main boom head for single line
work.
CAPACITY
30,000 kg at 3.0 m ELEVATION
By a double-acting hydraulic cylinder, fitted with a holding valve.
BOOM Automatic speed reduction and slow stop function.
4-section full power partially synchronized telescoping boom of Boom angle…………………… 0˚ to 81˚
Boom raising speed...........….. 20˚ to 60˚ in 22s
round hexagonal box construction with 3 sheaves at boom
head. The synchronization system consists of 2 telescope
HOIST-Main winch
cylinders, extension cables and retraction cables.
Variable speed type with grooved drum driven by hydraulic
Hydraulic cylinders fitted with holding valves.
axial piston motor through winch speed reducer. Power load
Fully retracted length ......................9.7 m
lowering and hoisting.
Fully extended length .....................31.0 m Equipped with automatic brake (Neutral brake) and
Extension speed .............................21.3 m in 91 s counterbalance valve.
Controlled independently of auxiliary winch.
JIB Single line pull ..................39.2 kN {4,000 kgf}
2-staged swingaround boom extension. Triple offset Single line speed..............125 m/min (at the 4th layer)
(5o/25o/45o) type. Box type top section telescopes from lattice Wire rope..........................Spin-resistant type
type base section which stows alongside base boom section. Diameter x length .............16 mm x 170 m
Single sheave at jib head.
Length.............................................7.2 m and 12.8 m HOOK BLOCK - 30 t capacity
4 sheaves, swivel type hook with safety latch.
CRANE SPECIFICATIONS
SPEC. SHEET NO. GR-300E-2-00102/EX-01

HOIST-Auxiliary winch TADANO Automatic Moment Limiter (AML)(Model:AML-C)

Variable speed type with grooved drum driven by hydraulic Main unit in crane cab gives audible and visual warning of
axial piston motor through winch speed reducer. Power load approach to overload. Automatically cuts out crane motions
lowering and hoisting. before overload.
Equipped with automatic brake (Neutral brake) and counter- With working range (load radius and/or boom angle and/or tip
balance valve. height and/or swing range) limit function.
Controlled independently of main winch. Automatic Speed Reduction and Soft Stop function on boom
Single line pull .................39.2 kN {4,000 kgf} elevation and swing.
Single line speed.............125 m/min (at the 4th layer) Following functions are displayed.
Wire rope.........................Spin-resistant type Load as percentage
Diameter x length ............16 mm x 98 m Number of parts of line of rope
Boom angle
Boom length
HOOK BLOCK - 4.0 t capacity Load radius
Swivel hook with safety latch for single line use. Outriggers position
On-tire indicator
SWING Actual hook load
Hydraulic axial piston motor driven through planetary Permissible load
speed reducer. Continuous 360o full circle swing on ball Boom position indicator
bearing slew ring. Equipped with manually locked/released Potential hook height
swing brake. Swing angle
Swing speed................3.2 min-1 {rpm} Main hydraulic oil pressure
Jib length and jib offset angle (only when jib operation)

HYDRAULIC SYSTEM OUTRIGGERS

Pumps..................2 variable piston pumps for telescoping, Hydraulically operated H-type outriggers. Each outrigger
elevating and winches. controlled simultaneously or independently from the cab.
Tandem gear pump for steering, swing and Equipped with sight level gauge. Floats mounted integrally
optional equipment. with the jacks retract to within vehicle width.
Control valves ......Multiple valves actuated by pilot pressure All cylinders fitted with pilot check valves.
with integral pressure relief valves. Crane operation with different extended length of each outrigger.
Circuit...................Equipped with air cooled type oil cooler. Equipped with extension width detector for each outrigger.
Oil pressure appears on AML display for Extended width
main circuit. Fully .............…..….......… 6,300mm
Hydraulic oil tank capacity...... Middle ............…..…......… 5,900mm
approx. 380 liters Middle ............…..…..…… 5,000mm
Filters ...................Return line filter Minimum .............…..….... 2,200mm
Float size (Diameter) ......... 400mm
CRANE CONTROL
By 4 control levers for swing, boom hoist, main winch, boom
telescoping or auxiliary winch with 2 control pedals for boom COUNTERWEIGHT
hoist and boom telescoping based on ISO standard layout. Integral with swing frame
Control lever stands can change neutral positions and tilt for Mass................................. 2,380 kg
easy access to cab.
NOTE : Each crane motion speed is based on unladen conditions.
CAB
Both crane and drive operations can be performed from one
cab mounted on rotating superstructure. One sided one-man
type, steel construction with sliding door access and tinted
safety glass windows opening at side. Door window is powered
control.
Operator's 3 way adjustable seat with headrest and armrest.
Hot water cab heater and air conditioning.

-2-
CARRIER SPECIFICATIONS
SPEC. SHEET NO. GR-300E-2-00102/EX-01

TYPE STEERING
Rear engine, left hand steering, driving axle 2-way selected Hydraulic power steering controlled by steering wheel.
type (by manual switch). Three steering modes available:
4 x 2 front drive 2-wheel front
4 x 4 front and rear drive 4-wheel coordinated
4-wheel crab
FRAME
High-tensile steel, all welded mono-box construction. SUSPENSION
Front ........Semi-elliptic leaf springs with hydraulic lockout
ENGINE device.
Model.......Cummins QSB6.7 [EUROMOT Stage ΙΙΙ A] Rear..........Semi-elliptic leaf springs with hydraulic lockout
Type.........4 cycle, turbo charged and after cooled, 6 cylinder device.
in line, direct injection, water cooled diesel engine.
Piston displacement ....6,700 cm3 BRAKE SYSTEM
Bore x stroke ...............107 mm x 124 mm Service ....Air over hydraulic disc brakes on all 4 wheels.
Max. output..................160 kW {220 PS} at 2,500 min-1 {rpm} Parking / Emergency.....
Max. torque .................843 N-m {86 kgf-m} at 1,600 min-1 {rpm} Spring applied-air released brake acting on input
shaft of front axle.
Auxiliary....Electro-pneumatic operated exhaust brake.
TRANSMISSION
Electronically controlled full automatic transmission. ELECTRIC SYSTEM
Torque converter driving full powershift with driving axle selector. 24 V DC. 2 batteries of 12 V - 120 Ah capacity.
6 forward and 2 reverse speeds.
2 speeds - High range - 2 wheel drive ; 4 wheel drive FUEL TANK CAPACITY
4 speeds - Low range - 4 wheel drive 300 liters

AXLES TIRES
Front ......Full floating type, steering and driving axle with planetary Front ........445 / 95 R 25(OR), Single x 2
reduction. Rear..........445 / 95 R 25(OR), Single x 2
Rear.......Full floating type, steering and driving axle with planetary
reduction. TURN RADIUS
Non-spin differential. Min. turning radius (at center of extreme outer tire)
2-wheel steering ........ 9.8 m
4-wheel steering ........ 5.8 m

EQUIPMENT
STANDARD EQUIPMENT 3 way adjustable cloth seat with seat belt, headrest and armrest
Automatic moment limiter (AML) Cab floor mat
External lamp (AML) Sun visor (front and roof)
Pendant type over-winding cutout Automatic drive system
Winch automatic fail-safe brake Transmission neutral position engine start
Cable follower Overshift prevention
30 t capacity hook block (4 sheaves) Parking braked travel warning
4.0 t capacity hook block (swivel hook) Tilt-telescope steering wheel
Hook safety latch Emergency steering
Pilot check valves Back-up alarm
Holding valves Air cleaner dust indicator
Counterbalance valves Air dryer
Hydraulic pressure relief valves Water separator with filter
Swing brake Engine over-run alarm
Swing lock Hydraulic lockout suspension
Boom angle indicator Non-spin differential (rear)
Boom elevation foot pedal Towing eyes - front and rear
Boom telescoping foot pedal Telematics(machine data logging and monitoring system) with
Outrigger extension width detector HELLO-NET via internet (availability depends on countries).
Air conditioner (hot water heater and cooler) Eco mode system
Winch drum rotation indicator (audible and visual type)
Sight level gauge
Fuel consumption monitor
Hydraulic oil cooler
Positive control
Electric windshield wiper and washer
Eco mode system
Roof window wiper and washer
Power window (Cab door)
Tachometer/Speedometer OPTIONAL EQUIPMENT
Over-unwinding prevention
Tire inflation kit

-3-
WORKING RANGE
SPEC. SHEET NO. GR-300E-2-00102/EX-01

BOOM
25˚ 45
˚
5˚

Approx.
45 1.9m

31
.0m
bo 40
om
+1
31 2.
8m
.0m
j 35 JIB
81˚ bo
om

ib
70˚ +7

LIFTING HEIGHT (m)

.2
60˚ 30
m

31 Approx.
jib

.0 m 2.0m
bo 50˚
om
24 45˚ 25
.4m
bo 40˚
o
35˚
m

20
16 30˚ SINGLE TOP
.8 0.67m
m
25˚
15
bo
om

20˚ Approx.
9. 2.0m
7
10
m
bo

10˚
om

5
0˚
Boom Length
0
0 5 10 15 20 25 30 35
RADIUS (m) 9.7m

16.8m

24.4m

31.0m

NOTE: The above lifting height and boom angle are based on a straight (unladen) boom,
and allowance should be made for boom deflection obtained under laden conditions.
The above working range is shown on condition with outriggers fully (6.3m) extended.

-4-
RATED LIFTING CAPACITIES ISO4305
SPEC. SHEET NO. GR-300E-2-00102/EX-01

ON OUTRIGGERS
ON OUTRIGGERS FULLY EXTENDED 6.3m SPREAD
360˚ ROTATION (Unit: ×1000kg)
A 9.7m 16.8m 24.4m 31.0m
B C C C C
3.0 60.6 30.0 74.4 19.2 79.7 12.5
3.5 57.0 27.2 72.5 19.2 78.5 12.5
4.0 53.1 23.4 70.9 19.2 77.5 12.5 80.8 8.4
4.5 49.2 21.3 68.9 18.3 76.3 12.5 80.0 8.4
5.0 44.7 19.6 67.1 17.0 75.0 12.5 79.1 8.4
5.5 40.3 18.1 65.1 15.8 74.0 12.5 78.3 8.4
6.0 34.9 16.6 63.3 14.7 72.8 12.5 77.3 8.4
6.5 28.7 15.2 61.4 13.6 71.5 11.7 76.6 8.4
7.0 18.3 14.1 59.4 12.9 70.3 11.0 75.6 8.1
8.0 54.9 10.9 67.7 9.75 73.7 7.5
9.0 50.5 9.0 65.0 8.75 71.8 6.8
10.0 45.8 7.05 62.4 7.9 69.8 6.2
11.0 40.3 5.8 59.5 6.6 67.6 5.8
12.0 34.3 4.8 56.5 5.6 65.6 5.4
13.0 27.0 4.05 53.6 4.75 63.5 5.0
14.0 15.7 3.4 50.4 4.15 61.3 4.4
15.0 47.0 3.6 59.0 3.85
16.0 43.4 3.2 56.6 3.45
17.0 39.6 2.75 54.2 3.05
18.0 35.5 2.45 51.8 2.65
19.0 30.7 2.05 49.2 2.4
20.0 25.6 1.8 46.6 2.1
22.0 40.8 1.7
24.0 34.4 1.3
26.0 26.2 1.0
28.0 13.4 0.5
D 0˚

LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE

ON OUTRIGGERS FULLY EXTENDED 6.3m SPREAD 360˚ ROTATION
A 9.7m 16.8m 24.4m 31.0m
C B B B B
0˚ 7.2 13.4 14.3 3.2 21.9 1.2 28.5 0.5
A: Boom length (m)
B: Load radius (m)
C: Loaded boom angle ( ˚)

ON OUTRIGGERS
ON OUTRIGGERS FULLY EXTENDED 6.3m SPREAD
360˚ ROTATION (Unit: ×1000kg)
31.0m Boom + 7.2m Jib 31.0m Boom + 12.8m Jib
C 5˚Tilt 25˚Tilt 45˚Tilt C 5˚Tilt 25˚Tilt 45˚Tilt
R W R W R W R W R W R W
80˚ 5.9 3.5 8.1 2.4 9.8 1.7 80˚ 7.7 2.2 11.7 1.2 14.6 0.8
77.5˚ 7.7 3.5 9.8 2.3 11.4 1.65 77.5˚ 9.8 2.15 13.5 1.15 16.3 0.78
75˚ 9.4 3.5 11.4 2.2 12.9 1.6 75˚ 11.8 2.1 15.3 1.1 17.9 0.75
72.5˚ 11.2 3.23 13.0 2.1 14.4 1.55 72.5˚ 13.6 1.93 17.1 1.05 19.4 0.73
70˚ 12.7 2.95 14.6 2.0 15.8 1.5 70˚ 15.5 1.75 18.8 1.0 21.0 0.7
67.5˚ 14.3 2.75 16.1 1.93 17.2 1.45 67.5˚ 17.2 1.63 20.5 0.95 22.5 0.68
65˚ 15.8 2.55 17.5 1.85 18.6 1.4 65˚ 18.9 1.5 22.0 0.9 23.9 0.65
62.5˚ 17.3 2.35 19.0 1.8 19.9 1.38 62.5˚ 20.6 1.4 23.6 0.88 25.2 0.65
60˚ 18.7 2.15 20.4 1.75 21.2 1.35 60˚ 22.3 1.3 25.1 0.85 26.6 0.65
57.5˚ 20.0 1.95 21.6 1.65 22.4 1.33 57.5˚ 23.8 1.23 26.4 0.8 27.8 0.65
55˚ 21.4 1.75 22.9 1.55 23.6 1.3 55˚ 25.4 1.15 27.9 0.75 29.0 0.65
52.5˚ 22.6 1.55 24.0 1.38 24.7 1.23 52.5˚ 26.8 1.1 29.2 0.73 30.2 0.63
50˚ 23.9 1.35 25.2 1.2 25.7 1.15 50˚ 28.3 1.05 30.5 0.7 31.4 0.6
47.5˚ 25.0 1.18 26.3 1.1 26.7 1.1 47.5˚ 29.6 0.9 31.7 0.68 32.5 0.6
45˚ 26.0 1.0 27.3 1.0 27.7 1.0 45˚ 30.8 0.75 32.8 0.65 33.5 0.6
42.5˚ 27.1 0.9 28.2 0.9 42.5˚ 32.0 0.68 33.8 0.6
40˚ 28.1 0.8 29.1 0.8 40˚ 33.1 0.6 34.8 0.55
37.5˚ 29.0 0.7 30.0 0.7 37.5˚ 34.2 0.53 35.7 0.48
35˚ 30.0 0.6 30.8 0.6 35˚ 35.2 0.45 36.5 0.4
32.5˚ 30.8 0.53 31.5 0.53 32.5˚ 36.1 0.4
30˚ 31.6 0.45 32.2 0.45 30˚ 37.0 0.35
27.5˚ 32.3 0.4 32.8 0.38
25˚ 33.0 0.35 33.4 0.3
C: Boom angle
R: Load radius (m)
W: Rated lifting capacity
-5-
RATED LIFTING CAPACITIES ISO4305
SPEC. SHEET NO. GR-300E-2-00102/EX-01

ON OUTRIGGERS
ON OUTRIGGERS MID EXTENDED 5.9m SPREAD
360˚ ROTATION (Unit: ×1000kg)
A 9.7m 16.8m 24.4m 31.0m
B C C C C
3.0 60.6 30.0 74.4 19.2 79.7 12.5
3.5 57.0 27.2 72.5 19.2 78.5 12.5
4.0 53.1 23.4 70.9 19.2 77.5 12.5 80.8 8.4
4.5 49.2 21.3 68.9 18.3 76.3 12.5 80.0 8.4
5.0 44.7 19.6 67.1 17.0 75.0 12.5 79.1 8.4
5.5 40.3 18.1 65.1 15.8 74.0 12.5 78.3 8.4
6.0 34.9 16.6 63.3 14.7 72.8 12.5 77.3 8.4
6.5 28.7 15.2 61.4 13.6 71.5 11.7 76.6 8.4
7.0 18.3 12.9 59.4 12.6 70.3 11.0 75.6 8.1
8.0 54.9 9.65 67.7 9.75 73.7 7.5
9.0 50.5 7.7 65.0 8.75 71.8 6.8
10.0 45.8 6.25 62.1 7.05 69.8 6.2
11.0 40.3 5.15 59.4 5.95 67.6 5.8
12.0 34.3 4.2 56.5 4.95 65.5 5.3
13.0 27.0 3.5 53.4 4.2 63.2 4.5
14.0 15.7 2.9 50.2 3.55 61.1 3.85
15.0 46.9 3.05 58.8 3.35
16.0 43.3 2.6 56.5 2.85
17.0 39.5 2.25 54.0 2.5
18.0 35.2 1.85 51.6 2.2
19.0 30.6 1.6 49.1 1.85
20.0 25.1 1.35 46.4 1.6
22.0 40.4 1.15
24.0 33.6 0.8
26.0 25.6 0.55
D 0˚

LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE

ON OUTRIGGERS FULLY EXTENDED 5.9m SPREAD 360˚ ROTATION
A 9.7m 16.8m 24.4m 31.0m
C B B B B
0˚ 7.2 12.0 14.3 2.7 21.9 0.9 28.5 0.3
A: Boom length (m)
B: Load radius (m)
C: Loaded boom angle ( ˚)
D: Minimum boom angle ( ˚) for indicated boom length (no load)

ON OUTRIGGERS
ON OUTRIGGERS MID EXTENDED 5.9m SPREAD
360˚ ROTATION (Unit: ×1000kg)
31.0m Boom + 7.2m Jib 31.0m Boom + 12.8m Jib
C 5˚Tilt 25˚Tilt 45˚Tilt C 5˚Tilt 25˚Tilt 45˚Tilt
R W R W R W R W R W R W
80˚ 5.9 3.5 8.1 2.4 9.8 1.7 80˚ 7.7 2.2 11.7 1.2 14.6 0.8
77.5˚ 7.7 3.5 9.8 2.3 11.4 1.65 77.5˚ 9.8 2.15 13.5 1.15 16.3 0.78
75˚ 9.4 3.5 11.4 2.2 12.9 1.6 75˚ 11.8 2.1 15.3 1.1 17.9 0.75
72.5˚ 11.2 3.23 13.0 2.1 14.4 1.55 72.5˚ 13.6 1.93 17.1 1.05 19.4 0.73
70˚ 12.7 2.95 14.6 2.0 15.8 1.5 70˚ 15.5 1.75 18.8 1.0 21.0 0.7
67.5˚ 14.3 2.75 16.1 1.93 17.2 1.45 67.5˚ 17.2 1.63 20.5 0.95 22.5 0.68
65˚ 15.8 2.55 17.5 1.85 18.6 1.4 65˚ 18.9 1.5 22.0 0.9 23.9 0.65
62.5˚ 17.3 2.35 19.0 1.8 19.9 1.38 62.5˚ 20.6 1.4 23.6 0.88 25.2 0.65
60˚ 18.7 2.15 20.4 1.75 21.2 1.35 60˚ 22.3 1.3 25.1 0.85 26.6 0.65
57.5˚ 20.0 1.88 21.6 1.6 22.4 1.33 57.5˚ 23.8 1.23 26.4 0.8 27.8 0.65
55˚ 21.4 1.6 22.9 1.45 23.6 1.3 55˚ 25.4 1.15 27.9 0.75 29.0 0.65
52.5˚ 22.6 1.35 24.0 1.25 24.7 1.15 52.5˚ 26.8 1.0 29.2 0.73 30.2 0.63
50˚ 23.9 1.1 25.1 1.05 25.7 1.0 50˚ 28.2 0.85 30.4 0.7 31.3 0.6
47.5˚ 25.0 0.95 26.1 0.9 26.7 0.88 47.5˚ 29.5 0.73 31.6 0.63 32.3 0.55
45˚ 26.0 0.8 27.1 0.75 27.7 0.75 45˚ 30.7 0.6 32.7 0.55 33.3 0.5
42.5˚ 27.1 0.68 28.1 0.63 42.5˚ 31.9 0.48 33.7 0.45
40˚ 28.1 0.55 29.0 0.5 40˚ 33.1 0.35 34.7 0.35
37.5˚ 29.0 0.48 29.8 0.43
35˚ 30.0 0.4 30.7 0.35
C: Boom angle ( ˚)
R: Load radius (m)
W: Rated lifting capacity

-6-
RATED LIFTING CAPACITIES ISO4305
SPEC. SHEET NO. GR-300E-2-00102/EX-01

ON OUTRIGGERS
ON OUTRIGGERS MID EXTENDED 5.0m SPREAD
360˚ ROTATION (Unit: ×1000kg)
A 9.7m 16.8m 24.4m 31.0m
B C C C C
3.0 60.6 30.0 74.4 19.2 79.7 12.5
3.5 57.0 27.2 72.5 19.2 78.5 12.5
4.0 53.1 23.4 70.9 19.2 77.5 12.5 80.8 8.4
4.5 49.2 21.3 68.9 18.3 76.3 12.5 80.0 8.4
5.0 44.7 19.6 67.1 17.0 75.0 12.5 79.1 8.4
5.5 40.3 15.7 65.1 15.0 74.0 12.5 78.3 8.4
6.0 34.9 13.2 63.3 12.65 72.8 12.5 77.3 8.4
6.5 28.7 11.3 61.4 10.85 71.5 11.7 76.6 8.4
7.0 18.2 9.65 59.4 9.5 70.1 10.4 75.6 8.1
8.0 54.9 7.3 67.5 8.2 73.7 7.5
9.0 50.5 5.8 64.8 6.7 71.8 6.8
10.0 45.8 4.7 62.0 5.5 69.5 5.8
11.0 40.3 3.8 59.3 4.65 67.3 4.9
12.0 34.3 3.1 56.3 3.9 65.2 4.25
13.0 27.0 2.55 53.0 3.25 63.0 3.6
14.0 15.7 1.9 49.9 2.75 60.8 3.1
15.0 46.6 2.3 58.5 2.65
16.0 43.0 1.9 56.1 2.25
17.0 39.4 1.6 53.8 1.95
18.0 35.2 1.35 51.3 1.65
19.0 30.5 1.1 48.7 1.4
20.0 24.9 0.75 46.0 1.2
22.0 40.3 0.8
D 0˚ 26˚

LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE

ON OUTRIGGERS FULLY EXTENDED 5.0m SPREAD 360˚ ROTATION
A 9.7m 16.8m 24.4m
C B B B
0˚ 7.2 9.0 14.3 1.8 21.9 0.5
A: Boom length (m)
B: Load radius (m)
C: Loaded boom anglec
D: Minimum boom angle ( ˚) for indicated boom length (no load)

ON OUTRIGGERS
ON OUTRIGGERS MID EXTENDED 5.0m SPREA
360˚ ROTATION (Unit: ×1000kg)
31.0m Boom + 7.2m Jib 31.0m Boom + 12.8m Jib
C 5˚Tilt 25˚Tilt 45˚Tilt C 5˚Tilt 25˚Tilt 45˚Tilt
R W R W R W R W R W R W
80˚ 5.9 3.5 8.1 2.4 9.8 1.7 80˚ 7.7 2.2 11.7 1.2 14.6 0.8
77.5˚ 7.7 3.5 9.8 2.3 11.4 1.65 77.5˚ 9.8 2.15 13.5 1.15 16.3 0.78
75˚ 9.4 3.5 11.4 2.2 12.9 1.6 75˚ 11.8 2.1 15.3 1.1 17.9 0.75
72.5˚ 11.2 3.23 13.0 2.1 14.4 1.55 72.5˚ 13.6 1.93 17.1 1.05 19.4 0.73
70˚ 12.7 2.95 14.6 2.0 15.8 1.5 70˚ 15.5 1.75 18.8 1.0 21.0 0.7
67.5˚ 14.3 2.7 16.1 1.93 17.2 1.45 67.5˚ 17.2 1.63 20.5 0.95 22.5 0.68
65˚ 15.8 2.45 17.5 1.85 18.6 1.4 65˚ 18.9 1.5 22.0 0.9 23.9 0.65
62.5˚ 17.1 2.05 18.9 1.65 19.9 1.38 62.5˚ 20.6 1.38 23.6 0.88 25.2 0.65
60˚ 18.6 1.65 20.2 1.45 21.1 1.35 60˚ 22.2 1.25 25.1 0.85 26.6 0.65
57.5˚ 19.8 1.38 21.5 1.23 22.3 1.15 57.5˚ 23.7 1.03 26.5 0.75 27.8 0.65
55˚ 21.1 1.1 22.7 1.0 23.4 0.95 55˚ 25.1 0.8 27.7 0.65 29.0 0.65
52.5˚ 22.4 0.93 23.9 0.83 24.5 0.8 52.5˚ 26.5 0.65 29.0 0.55 30.2 0.55
50˚ 23.6 0.75 25.0 0.65 25.5 0.65 50˚ 27.9 0.5 30.3 0.45 31.2 0.45
47.5˚ 24.8 0.6 26.1 0.5 26.6 0.5
45˚ 25.9 0.45 27.1 0.35 27.5 0.35
C: Boom angle ( ˚)
R: Load radius (m)
W :Rated lifting capacity (Unit:×1000kg)

-7-
RATED LIFTING CAPACITIES ISO4305
SPEC. SHEET NO. GR-300E-2-00102/EX-01

ON OUTRIGGERS
ON OUTRIGGERS MIN EXTENDED 2.2m SPREAD
360˚ ROTATION (Unit: ×1000kg)
A 9.7m 16.8m 24.4m 31.0m
B C C C C

3.0 60.6 13.2 74.2 13.0 79.5 12.5

3.5 57.0 10.25 72.2 9.8 78.4 10.9
4.0 53.1 8.0 70.5 7.8 77.2 8.8 79.9 8.0
4.5 49.2 6.7 68.4 6.45 75.9 7.25 79.0 7.2
5.0 44.7 5.7 66.8 5.3 74.6 6.2 77.9 6.05
5.5 40.3 4.7 64.6 4.4 73.3 5.2 77.0 5.45
6.0 34.9 3.85 62.8 3.65 72.0 4.4 76.1 4.8
6.5 28.7 3.3 60.9 3.05 70.6 3.8 75.1 4.25
7.0 18.3 2.7 58.7 2.6 69.5 3.3 74.1 3.65
8.0 54.6 1.85 66.7 2.4 72.3 2.75
9.0 50.2 1.2 64.1 1.75 70.3 2.05
10.0 45.1 0.55 61.3 1.35 68.3 1.5
11.0 58.7 0.95 66.2 1.2
12.0 55.9 0.55 64.3 0.9
13.0 62.2 0.5
D 0˚ 40˚ 53˚ 60˚

LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE

ON OUTRIGGERS MIN EXTENDED 2.2m SPREAD 360˚ ROTATION
A 9.7m
C B
0˚ 7.2 2.5
A: Boom length (m)
B: Load radius (m)
C: Loaded boom angle ( ˚)
D: Minimum boom angle ( ˚) for indicated boom length (no load)

NOTES FOR “ON OUTRIGGERS” TABLE

1. Rated lifting capacities shown in the table are based on condition that crane is set on firm level surface. Those above thick lines are
based on crane strength and those below, on its stability.
2. Rated lifting capacities based on crane stability are according to ISO 4305.
3. The mass of the hook (270kg for 30 t capacity, 100kg for 4.0 t capacity), slings and all similarly used load handling devices must be
considered as part of the load and must be deducted from the lifting capacities.
4. For rated lifting capacity of single top, reduce the rated lifting capacities of relevant boom according to a weight reduction for auxil-
iary load handling equipment. Capacities of single top shall not exceed 4,000 kg including main boom hook mass and the net
capacity must be so reduced.
5. Standard number of parts of line for each boom length is as shown below. Load per line should not surpass 39.2 kN {4,000 kgf} orf
main winch and auxiliary winch.

Boom length 9.7m 9.7m to 16.8m 16.8m to 31.0m Single top / Jib
Number of 8 6 4 1
parts of line

The lifting capacity data stored in the AUTOMATIC MOMENT LIMITER (AML-L) is based on the standard number of parts of line listed
in the chart.
Maximum lifting capacity is restricted by the number of parts of line of AUTOMATIC MOMENT LIMITER (AML-L).
6. The lifting capacity for over-side area differs depending on the outrigger extension width. Work with the capacity corresponding to
the extension width. The lifting capacities for over-front and over-rear areas are for “outriggers fully extended”. However, the areas
(angle a) differ depending on the outrigger extension width.

Outriggers extended width 5.9m(middle) 5.0m(middle) 2.2m(minimum)

Angle a˚ 45 40 15

a a

a a

-8-
RATED LIFTING CAPACITIES ISO4305
SPEC. SHEET NO. GR-300E-2-00102/EX-01

ON RUBBER (ON TIRES)

ON RUBBER STATIONARY (Unit: ×1000kg)
A Over Front 360˚ Rotation
9.7m 16.8m 24.4m 9.7m 16.8m 24.4m
B C C C C C C
3.0 60.6 18.0 60.6 11.0
3.5 56.8 17.0 57.1 9.0
4.0 53.0 15.0 53.5 7.3
4.5 49.2 12.7 68.8 11.0 49.7 5.7 68.5 5.5
5.0 44.9 10.6 66.9 9.5 45.4 4.9 66.3 4.5
5.5 39.9 9.0 64.9 8.0 40.8 4.0 64.6 3.7
6.0 34.6 7.7 63.1 7.0 35.3 3.2 62.5 3.1
6.5 27.7 6.6 61.1 6.1 28.9 2.75 60.9 2.5
7.0 17.7 5.7 59.0 5.3 20.5 2.27 58.6 2.1
8.0 54.6 4.25 67.2 5.0 54.6 1.4 66.9 2.2
9.0 50.0 3.45 64.3 3.9 49.9 0.85 64.3 1.6
10.0 45.2 2.65 61.6 3.15 61.6 1.1
11.0 40.1 2.1 58.8 2.55 58.7 0.8
12.0 33.8 1.6 55.9 2.1
13.0 26.5 1.2 52.9 1.75
14.0 15.7 0.75 49.7 1.4
15.0 46.7 1.1
16.0 43.1 0.85
17.0 39.4 0.6
D 0˚ 28˚ 0˚ 44˚ 56˚

LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE

ON RUBBER STATIONARY
A Over Front 360˚ Rotation
9.7m 16.8m 9.7m
C B B B
0˚ 7.2 5.4 14.3 0.7 7.2 2.1

A: Boom length (m)

B: Load radius (m)
C: Loaded boom angle ( ˚)
D: Minimum boom angle ( ˚) for indicated boom length (no load)

ON RUBBER (ON TIRES)

ON RUBBER CREEP (Unit: ×1000kg)
Over Front 360˚ Rotation
A 9.7m 16.8m 24.4m 9.7m 16.8m 24.4m
B C C C C C C
3.0 60.6 18.0 60.6 10.0
3.5 56.8 15.45 57.0 8.0
4.0 53.0 13.0 53.3 6.5
4.5 49.0 11.1 68.6 9.7 49.2 5.1 68.6 5.1
5.0 44.7 9.3 66.6 8.4 44.4 4.3 66.6 4.2
5.5 39.8 7.95 64.6 7.0 39.6 3.7 64.7 3.5
6.0 34.7 6.7 62.8 6.0 34.0 3.0 62.7 2.7
6.5 28.0 5.75 60.8 5.3 27.0 2.5 60.7 2.35
7.0 18.2 5.0 58.7 4.65 18.1 1.95 58.9 1.85
8.0 54.4 3.6 67.0 4.3 54.5 1.3 67.0 1.9
9.0 49.9 2.8 64.3 3.4 50.2 0.75 64.3 1.35
10.0 45.1 2.3 61.7 2.8 61.7 0.9
11.0 39.6 1.8 58.8 2.25 58.8 0.6
12.0 33.3 1.35 56.0 1.8
13.0 26.0 1.0 52.9 1.5
14.0 14.6 0.6 49.7 1.2
15.0 46.4 0.95
16.0 42.9 0.6
D 0˚ 31˚ 0˚ 44˚ 56˚

LIFTING CAPACITIES AT ZERO DEGREE BOOM ANGLE

ON RUBBER CREEP
A Over Front 360˚ Rotation
9.7m 16.8m 9.7m
C B B B
0˚ 7.2 4.7 14.3 0.5 7.2 1.8
A: Boom length (m)
B: Load radius (m)
C: Loaded boom angle ( ˚)
D: Minimum boom angle ( ˚) for indicated boom length (no load)

-9-
RATED LIFTING CAPACITIES ISO4305
SPEC. SHEET NO. GR-300E-2-00102/EX-01

NOTES FOR “ON RUBBER” TABLE

1. Rated lifting capacities shown in the table are based on condition that crane is set on firm level surface, with suspension lock
applied. Those above thick lines are based on tire capacity and those below, on crane stability. They are based on actual load
radius increased by tire deformation and boom deflection.
2. Rated lifting capacities based on crane stability are according to ISO 4305.
3. The mass of the hook (270 kg for 30 t capacity, 100 kg for 4.0 t capacity), slings and all similarly used load handling devices must
deducted from the lifting capacities.
4. For rated lifting capacity of single top, reduce the rated lifting capacities of relevant boom according to weight reductions for auxil-
iary load handling equipment. Capacities of single top shall not exceed 4,000 kg including main hook.
5. On rubber lifting with "jib" is not permitted. Maximum permissible boom length is 24.4 m.
6. CREEP is motion for crane not to travel more than 60 m in any 30 minute period and to travel at the speed of less than 1.6 km/h.
7. During "CREEP" duties travel slowly and keep the lifting load as close to the ground as possible, and especially avoid any abrupt
steering, accelerating or braking.
8. Do not operate the crane while carrying the load.
9. Tires should be inflated to their correct air pressure of 900kPa.
10. For CREEP operation, choose the drive mode and proper gear according to the road or working condition.
11. Standard number of parts of line for on rubber operation should be according to the following table.
Load per line should not surpass 39.2kN {4,000kgf} for main winch and auxiliary winch.
Boom length 9.7m 9.7m to 24.4m Single top
Number of 6 4 1
parts of line

The lifting capacity data stored in the AUTOMATIC MOMENT LIMITER (AML) is based on the standard number of parts of line
listed in the chart.
Maximum lifting capacity is restricted by the number of parts of line of AUTOMATIC MOMENT LIMITER (AML).

WORKING AREA

Over 360˚
front
Rear

approx. Without outriggers "Over front" operation should be performed within

2 degrees in front of chassis.
2˚

- 10 -
DIMENSION
SPEC. SHEET NO. GR-300E-2-00102/EX-01

5,000(O/R Mid1)
5,900(O/R Mid2)
6,300(O/R Max)
2,200(O/R Min)
R3
,33
0
MIN: 9,700 - MAX: 31,000
2,460
3,535

3,480
12.6˚
15.3˚

385
2,140 1,750
2,620 3,030 3,350
7,300
5,725 3,500 2,020
11,245

Note: Dimension is with boom angle at 0 degree.

Axle Weight Distribution Chart Unit : kg

GVW Front Rear
Basic standard machine includes:
4-section boom (9.7 m - 31.0 m)
2-stage jib (7.2 m, 12.8 m)
Cummins QSB6.7 27,190 13,650 13,540
445 / 95R 25 tires
Single top
30 ton 4 sheaves hook block
4.0 ton hook block
Remove:
1. 2-stage jib (7.2 m, 12.8 m) -630 -1,085 +455
2. 30 ton 4 sheaves hook block -270 -480 +210
3. 4.0ton hook block -100 -140 +40

- 11 -
Specifications are subject to change without notice.

(International Division)
4-12, Kamezawa 2-chome,
Sumida-ku, Tokyo 130-0014, Japan
Te l : 81-(0)3-3621-7750
Fax : 81-(0)3-3621-7785
URL http : // www.tadano.co.jp / indexe.htm
E-mail [email protected]

Printed in Japan
GR-300EX-2012-06-3