DG-TX7
Intelligent Flammable Gas Detector Presentation
The MultiXplo DG-TX7 is an intelligent catalytic sensor based
flammable gas detector used to detect a wide range of gases,
including hydrogen (H2). The device has been designed for ease of
installation, operation and maintenance in testing environments.
The MultiXplo DG-TX7 employs a pair of OXYCOL catalytic sensors
in a compensated circuitry in order to provide reliable flammable gas
detection in harsh environments, as long as oxygen is present.
The intelligent microprocessor driven unit is fully configurable using
a wireless handheld terminal (TLU) or optionally via HART giving
true flexibility to the installer. Parameters such as relay operation and
alarm levels are all set via the TLU; a hazardous area approved hand-
held unit. In addition, the sensor element is protected by the onboard
electronics to prevent exposure to over-range LEL gas concentrations.
This helps reduce on-going maintenance and service costs.
Users can select between 4-20 and 0-22mA depending on system
requirements. The unit may be interfaced directly with a wide range of
panels, controllers and PLC’s etc.
Device status, including measured gas level is indicated on a colour
coded 4 digit LED display.
TLU Wireless (IR)
Hand-held Terminal
Features
• High visible display
• On board relays
• Display color is status dependent
DG-TX7
Intelligent Flammable Gas Detector
General Conformities
Technology Low temperature oxidation process, Oxycol EN60079-29-1
Detects Flammable Gases
Accessories
Range 0 to 100% LEL
TLU600 Infrared remote control unit
Calibration with calibration gas
AS056-250 Sun shade
Performance AS005 Calibration cup
Response time T90 < 15 s (Methane) AS047 Display protection
Zero drift +/- 3% Full scale deflection AS011 -2 Sample flow housing
Accuracy +/- 5% Full scale deflection
AS019 Splash guard
Repeatability +/- 1% Full scale deflection
CAL-K1 C-xxDF-1 A1 -00 Calibration kit 20ppm H2S
Sensor life Better than 5 years
Output signal
4-20mA, max. load impedance 700M (Std. )
Standard
2 x configurable Relays max 1 A / 30V
option HART (R) HART Protocol (7th edition)
option 0-22mA (User configurable)
option Lonworks (Syntel)
Local display 4 digit led display and backlight color status
with automatic intensity adjustment
Electrical
Power supply 24V DC, range (18 - 28V DC)
Power consumption 2W normal, 5W max (backlight at max)
Connection 0.3 mm2 (22 AWG) - 1.5 mm2 (16 AWG)
Shielded cable recommended
Environmental
Storage -20°C TO +70°C (-4°F TO 1 58°F)
Operation -20°C TO +60°C (-4°F TO 1 40°F)
Option Sunshade, max. temp. 85°C (185°F)
Humidity 99% RH (non-condensing)
Pressure Atmospheric pressure +/- 10%
Ingress IP66
RFI /EMI Complies with EN50270
Housing
Material 316L stainless steel
Weight 4 Kg (8Lbs)
Approvals
ATEX II 2 G Ex d IIC T6 Gb (-20°C to +65°C)
(-4°F to +149°F)
IECEx Ex d IIC T6 Gb
IECEx LCI 11.0060X
Teledyne Oldham Simtronics’ quality assurance programs require continuous assessment and improvement of all our products. Therefore, the information in this leaflet may change without prior notification and should not be considered a product specifi-
cation. If you require more details, please don’t hesitate to contact Teledyne Oldham Simtronics or one of their representatives.
AMERICAS EMEA ASIA PACIFIC
4055 Technology Forest Blvd. ZI Est, Rue Orfila, Room 04, 9th Floor,
The Woodlands, CS 20417 275 Ruiping Road,
TX 77381, USA 62027 ARRAS CEDEX, France Xuhui District, Shanghai,
Tel.: +1-713-559-9200 Tel.: +33-3-21-60-80-80 China
Fax: +1-713-893-6729 Fax.: +33-3-21-60-80-00
[email protected]Copyright © 2024 Teledyne Technologies GF-30083F_EN. All rights reserved. www.teledynegasandflamedetection.com
