PRODUCT DATA SHEET
Sikadur®-330
2-COMPONENT EPOXY IMPREGNATION RESIN
DESCRIPTION CHARACTERISTICS / ADVANTAGES
Sikadur®-330 is a 2-component, thixotropic epoxy ▪ Easy mix and application by trowel and impregnation
based impregnating resin and adhesive. roller
Suitable for use in hot and tropical climatic conditions. ▪ Manufactured for manual saturation methods
▪ Excellent application behaviour to vertical and over-
USES head surfaces
▪ Good adhesion to many substrates
Sikadur®-330 may only be used by experienced profes- ▪ High mechanical properties
sionals. ▪ No separate primer required
Sikadur®-330 is used as:
▪ Impregnation resin for SikaWrap® fabric reinforce- SUSTAINABILITY
ment for the dry application method
▪ Primer resin for the wet application system Sikadur®-330 is certified according "Low Emitting Ma-
▪ Structural adhesive for bonding Sika® CarboDur® terials as per Al Sa'fat - Dubai Green Building Evalu-
plates into slits ation System" by Dubai Central Laboratory (DCL) certi-
ficate No. CL17020432
APPROVALS / CERTIFICATES
▪ Avis Technique N° 3/10-669 (annule et remplace N°
3/07-502) Sika® CarboDur®, SikaWrap®
▪ Road and Bridges Research Institute (Poland): IBDiM
No AT/2008-03-336/1
▪ Adhesive for structural bonding tested according to
EN 1504-4
PRODUCT INFORMATION
Composition Epoxy resin
Packaging 5 kg (A+B) Pre-batched unit
Not pre-dosed industrial packaging:
Component A 24 kg pails
Component B 6 kg pails
Note: Refer to mixing ratio and mixing clause in this Product Data Sheet.
Colour Component A: white paste
Component B: grey paste
Components A + B: light grey paste
Shelf life 24 months from date of production
Product Data Sheet
Sikadur®-330
April 2019, Version 03.01
020206040010000004
1/4
Storage conditions Store in original, unopened, sealed and undamaged packaging in dry condi-
tions at temperatures between +5 °C and +30 °C. Protect from direct sun-
light.
Density ~1.30 kg/l (mixed component A + B mixed) (+23 °C)
Viscosity Shear rate: 50/s
Temperature Viscosity
+10 °C ~10 000 mPas
+23 °C ~6 000 mPas
+35 °C ~5 000 mPas
TECHNICAL INFORMATION
Modulus of Elasticity in Flexure ~3 800 N/mm2 (7 d, +23 °C) (DIN EN 1465)
Tensile Strength ~30 N/mm2 (7 d, +23 °C) (ISO 527)
Modulus of Elasticity in Tension ~4 500 N/mm2 (7 d, +23 °C) (ISO 527)
Elongation at Break ~0.9 % (7 d, +23 °C) (ISO 527)
Tensile Adhesion Strength Concrete fracture (> 4 N/mm2) on sandblasted substrate (EN ISO 4624)
Coefficient of Thermal Expansion 4.5 × 10−5 1/K (Temperature range -10 °C min. / +40 °C max.) (EN 1770)
Glass Transition Temperature Curing time Curing temperat- TG (EN 12614)
ure
30 d +30 °C +58 °C
Heat Deflection Temperature Curing time Curing temperat- HDT (ASTM D 648)
ure
7d +10 °C +36 °C
7d +23 °C +47 °C
7d +35 °C +53 °C
Resistant to continuous exposure up to +45 °C.
Service Temperature -40 °C min. / +45 °C max.
SYSTEMS
System Structure Substrate primer: Sikadur®-330.
Impregnating / laminating resin: Sikadur®-330.
Structural strengthening fabric: SikaWrap® type to suit requirements.
APPLICATION INFORMATION
Mixing Ratio Component A : Component B = 4 : 1 (by weight)
When using bulk material the exact mixing ratio must be safeguarded by
accurately weighing and dosing each component.
Consumption See the "Method Statement for SikaWrap® manual dry application"
Ref: 850 41 02.
Guide: 0.7 - 1.5 kg/m2
Ambient Air Temperature +10 °C min. / +35 °C max.
Dew Point Beware of condensation.
Substrate temperature during application must be at least 3 °C above dew
point.
Substrate Temperature +10 °C min. / +35 °C max.
Substrate Moisture Content < 4 % pbw
Product Data Sheet
Sikadur®-330
April 2019, Version 03.01
020206040010000004
2/4
Pot Life Temperature Pot life Open time (EN ISO 9514)
+10 °C ~90 min (5 kg) ~90 min
+23 °C ~60 min (5 kg) ~60 min
+35 °C ~30 min (5 kg) ~30 min
The pot life begins when the resin and hardener are mixed. It is shorter at high temperatures and longer at
low temperatures. The greater the quantity mixed, the shorter the pot life. To obtain longer workability at
high temperatures, the mixed adhesive may be divided into portions. Another method is to chill compon-
ents A and B before mixing them (not below +5 °C).
APPLICATION INSTRUCTIONS IMPORTANT CONSIDERATIONS
SUBSTRATE QUALITY Sikadur®-330 must be protected from rain for at least
24 hours after application.
Substrate must be sound and of sufficient tensile Ensure placement of fabric and laminating with roller
strength to provide a minimum pull off strength of takes place within open time.
1.0 N/mm2 or as per the requirements of the design At low temperatures and / or high relative humidity, a
specification. tacky residue (blush) may form on the surface of the
See also the "Method Statement for SikaWrap® manu- cured Sikadur®-330 epoxy. If an additional layer of fab-
al dry application" Ref: 850 41 02. ric or a coating is to be applied onto the cured epoxy,
this residue must first be removed with warm, soapy
SUBSTRATE PREPARATION water to ensure adequate bond. In any case, the sur-
See the "Method Statement for SikaWrap® manual dry face must be wiped dry prior to application of the next
application" Ref: 850 41 02. layer or coating.
For application in cold or hot conditions, pre-condi-
MIXING tion material for 24 hours in temperature controlled
storage facilities to improve mixing, application and
Pre-batched units: pot life limits.
Mix components A+B together for at least 3 minutes For further information on over coating, number of
with a mixing spindle attached to a slow speed electric layers or creep, please consult a structural engineer
drill (maximum 300 rpm) until the material becomes for calculations and see also the "Method Statement
smooth in consistency and a uniform grey colour. for SikaWrap® manual dry application".
Avoid aeration while mixing. Then, pour the whole mix Sikadur® resins are formulated to have low creep un-
into a clean container and stir again for approximately der permanent loading. However due to the creep be-
1 more minute at low speed to keep air entrapment at haviour of all polymer materials under load, the long
a minimum. Mix only that quantity which can be used term structural design load must account for creep.
within its pot life. Generally the long term structural design load must be
lower than 20 to 25 % of the failure load. Please con-
Bulk packing, not pre-batched: sult a structural engineer for load calculations for the
First, stir each component thoroughly. Add the com- specific application.
ponents in the correct proportions into a suitable mix-
ing pail and stir correctly using an electric low speed
mixer as above for pre-batched units.
APPLICATION METHOD / TOOLS
See the "Method Statement for SikaWrap® manual dry
application" Ref: 850 41 02.
CLEANING OF EQUIPMENT
Clean all equipment immediately with Sika® Colma
Cleaner. Cured material can only be removed mechan-
ically.
Product Data Sheet
Sikadur®-330
April 2019, Version 03.01
020206040010000004
3/4
BASIS OF PRODUCT DATA LEGAL NOTES
All technical data stated in this Data Sheet are based The information, and, in particular, the recommenda-
on laboratory tests. Actual measured data may vary tions relating to the application and end-use of Sika
due to circumstances beyond our control. products, are given in good faith based on Sika's cur-
rent knowledge and experience of the products when
LOCAL RESTRICTIONS properly stored, handled and applied under normal
conditions in accordance with Sika's recommenda-
Note that as a result of specific local regulations the tions. In practice, the differences in materials, sub-
declared data and recommended uses for this product strates and actual site conditions are such that no war-
may vary from country to country. Consult the local ranty in respect of merchantability or of fitness for a
Product Data Sheet for the exact product data and particular purpose, nor any liability arising out of any
uses. legal relationship whatsoever, can be inferred either
from this information, or from any written recom-
ECOLOGY, HEALTH AND SAFETY mendations, or from any other advice offered. The
user of the product must test the product’s suitability
For information and advice on the safe handling, stor- for the intended application and purpose. Sika re-
age and disposal of chemical products, users shall refer serves the right to change the properties of its
to the most recent Safety Data Sheet (SDS) containing products. The proprietary rights of third parties must
physical, ecological, toxicological and other safety-re- be observed. All orders are accepted subject to our
lated data. current terms of sale and delivery. Users must always
refer to the most recent issue of the local Product Data
Sheet for the product concerned, copies of which will
be supplied on request.
SIKA NORTHERN GULF SIKA SOUTHERN GULF SIKA SAUDI ARABIA
Bahrain / Qatar / Kuwait UAE / Oman / SIC Riyadh / Jeddah / Dammam
Tel: +973 177 38188 Tel: +971 4 439 8200 Tel: +966 11 217 6532
[email protected] [email protected] [email protected]gcc.sika.com gcc.sika.com gcc.sika.com
Sikadur-330-en-AE-(04-2019)-3-1.pdf
Product Data Sheet
Sikadur®-330
April 2019, Version 03.01
020206040010000004
4/4
