technical

data sheet
Description Packaging and Storage
 Best stored at room temperature.
T-Lock is an innovative PVC membrane designed for waterproofing
 Keep away from sources of mechanical damage
subterranean areas such as basements, car parks, cellars, lift pits, tunnels
and similar water retaining structures. The design of the membrane  Recommended to be kept under cover.
provides one face that is “T” shaped that provides a secure mechanical
bond to concrete ensuring long term secure adhesion of concrete to the
membrane. Furthermore the durability of T-Lock is a key benefit for critical
underground applications with the ability to withstand mechanical damage, TECHNICAL DATA
chemical spillages and weather resistance.

Tensile Strength (longitudinal)

Features & Benefits ASTM D412: 17.25MPa

 Resistant to acidic, alkaline and general corrosive environments

Fix Key tensile strength >176N/cm
 Suitable on contaminated earth, hydrocarbons and gas emissions
 Outstanding durability, with flexible and high strength properties
Elongation at break
 Crack resistant, able to withstand substrate movement and stratigraphic (longitudinal):
225%
change
 Seamless sealing at wall floor junctions
Shore D Hardness ASTM
 Leak proof and vapour resistant D2240:
54-62
 Outstanding weather resistance while exposed to external conditions
 Light weight, easy of handling, provides time efficient application Tear strength ADTM D570: 110 N/mm
 Made by extrusion, PVC sheet is easily welded together to ensure high
strength lap joins and seams. Easily joined and extended in size. Water absorption ASTM D570 0.1% Within
 Puncture resistance and excellent trafficability for on site conditions
 Able to be applied to damp surfaces, free of surface water Plasticiser permeance ASTM
0.4% Within
D1203

Chemical Soaking Solution

Application ASTM D543

Sulphuric acid 20% 0.12%

T-Lock protects concrete against the ingress of water, gas and corrosive
subterranean solutions. Once concrete is applied over the T-Lock
membrane a mechanical high strength adhesion key is formed, ensuring Ammonium Hydroxide 5% 0.40%
concrete remains bonded and locked to the membrane surface. The PVC
Sodium Hydroxide 5% 0.10%
nature of T-Lock provides excellent ageing resistance and durability to
protect concrete against earth movement.
Ferric
Sodium Chloride
Hypo-chloride 1% 0.20%

Surface Preparation Ferric Chloride 1% 0.60%

Surfaces must be uniform, sound and even. Blinding slabs or compacted Nitric acid 1% 0.20%
sub base fills are to be free of surface water. T-Lock can be applied over
damp surfaces. Remove loose aggregate on the surface and ensure the
Soap & detergent solution 2% 0.40%
general area is free of sharp protrusive materials. For vertical surfaces, T-
Lock can be applied over form work or other structural surfaces that are
sound and in a stable condition.
Notes
Installing T-Lock It is recommended before commencing the application; that adhesion of products to be
used (e.g. primers, membranes, coatings adhesives etc) is tested over a typical area of the
prepared surface to ensure satisfactory adhesion. It is the responsibility of the applicator to
Full Method statement is available for fixing carry this out and accept the substrate suitability before any application starts. Gripset
Industries offers a service for pre testing adhesion to surfaces for large commercial areas or
 T-Lock sheet is unrolled, straightened and placed in position. unusual substrates. For further details contact Gripset Industries. Details contained in
 At wall/floor junctions, T sections are planed along a 150-200mm product data sheets are general. For any situation or items not covered in this data sheet, it
section to form a smooth surface to enable ease of bending at is the responsibility of the applicator to check with Gripset Technical Services before
commencing the application. A written confirmation will then be issued by Gripset Technical
junctions Services.
 Membrane onto vertical sections can be mechanically fixed to the
substrate. This penetration is over patched with a piece of PVC welded
to form a seamless seal.
Gripset Industries Pty Ltd
 Membrane is positioned in place on horizontal surfaces
ABN: 64 137 930 093
 Lapping is formed at a minimum 30mm. At all overlapped sections a
copper wire is incorporated in the lap for testing of seam integrity once Telephone: +61 (8) 8124-7300 or 1800 650 435
lapped sections are fully welded and sealed. Email: [email protected]
 This method is used on vertical, horizontal, overhead and complex Website: www.gripset.com
shapes without the use of any other sealing accessories to form a high
strength sealed system. Product Disclaimer
 External edges and penetrations are sealed with a high grade rapid PU
This Product Data Sheet (PDS) summarises our best knowledge of the product, including how to use
sealant/membrane. and apply the product based on the information available at the time. You should read this PDS
carefully and consider the information in the context of how the product will be used, including in
conjunction with any other product and the type of surfaces to, and the manner in which, the product
will be applied. Our responsibility for products sold is subject to our standard terms and conditions of
sale. Gripset Industries does not accept any liability either directly or indirectly for any losses suffered
in connection with the use or application of the product whether or not in accordance with any advice,
specification, recommendation or information given by it.

Page 1 of 1 Gripset T-Lock – Issue Date: February 2021