I.
CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
COMPANY INFORMATION
Materials Solutions Inc.
Suite 904-905 South Center Tower,
2206 Market St., Madrigal Business Park
Alabang, Muntinlupa City
Phone # : (632) 807-0993 / (632) 842-7959
Fax # : (632) 807-5303
PRODUCT INFORMATION
Product Name / Number: MATSOL TG 9000
II. INFORMATION ON COMPOSITION
CHEMICAL FAMILY: Water, Polymer, etc
Molecular Formula: Mixture
Hazardous: No
III. HAZARDS IDENTIFICATION
Not considered as hazardous.
EYE : As with any foreign materials in the eye, allowing
the product to remain in the eye may cause a mild
irritation.
SKIN CONTACT: Prolonged skin contact may cause mild irritation.
INHALATION: Not normally a problem under typical conditions of
industrial use. No health effects are expected.
Item proportion Cas.No
Water 60~70% 7732-18-5
PVOH 20~30% 9002-89-5
Antiseptic 0.1~1% 2634-33-5
Defoaming agent 0.1~1% 8042-47-5
IV. FIRST-AIDS MEASURES
EYE: If any should get into the eye, rinse with water until all
traces are washed away. Get medical attention immediately.
SKIN CONTACT: If any, wash contact areas thoroughly with soap and water.
Launder contaminated clothing before reuse.
INHALATION: If any, remove to fresh air. Give artificial respiration, if
necessary. Get medical attention.
INGESTION: Induce vomiting if ingestion is of a large amount.
V. FIRE FIGHTING MEASURES
AUTOIGNITION: Unknown.
FLASH POINT: N.A.
EXTINGUISHING MEDIA: Liquid material is non-flammable, dry
polymer film will burn. Any extinguishing
media is suitable for use on fry film fire,
such as CO2; Dry chemical; Foam
SPECIAL FIREFIGHTING PROCEDURES: No special procedures are required.
FIRE & EXPLOSION HAZARDS: Not applicable.
UPPER EXPLOSION LIMIT (%): Not applicable.
LOWER EXPLOSION LIMIT (%): Not applicable.
NFPA FLAMMABILITY HAZARD CLASS -- 0 = Insignificant
VI. ACCIDENTAL RELEASE MEASURES
SPILL & LEAK PROCEDURES: Spread absorbent materials. Shovel into closurable
containers.Wash area with water. For safety and environmental precautions, please review entire
Materials Safety Data Sheet for necessary information.
VII. HANDLING AND STORAGE
STORAGE TEMPERATURE: 6 – 35°C
HANDLING/STORAGE: Store at room temperature area. Avoiding
freezing.
VENTILATION REQUIREMENTS: Local; general
VIII. EXPOSURE CONTROLS / PERSONAL PROTECTION
VENTILATION REQUIREMENTS: Local; general
EYE PROTECTION REQUIREMENTS: Avoid contact with eyes. Wear chemical
goggles if there is likelihood of contact with
eyes.
GLOVE REQUIREMENTS: Use of chemical resistant gloves is
recommended.
CLOTHING REQUIREMENTS: Employee must wear appropriate protective
clothing and equipment to prevent any
possibility of skin contact with this
substance.
CHANGE/REMOVAL OF CLOTHING: Not required unless adhesive has been
splashed on clothing and passes through
fabric.
WASH REQUIREMENTS: None.
RESPIRATOR REQUIREMENTS: Not normally required for foreseeable
conditions of use.
IX. PHYSICAL AND CHEMICAL PROPERTIES
PURE SUBSTANCE OR MIXTURE: Mixture
PHYSICAL FORM: Liquid
APPEAREANCE/COLOR: White fluid
ODOR: Ammonia odor
ODOR THRESHOLD: Not available
pH: Approx. 5.0
BOILING POINT: 100°C
MELTING/FREEZING POINT: 0°C
SOLUBILITY IN WATER: Completely miscible
SPECIFIC GRAVITY (WATER=1): Approx. 1.0
EVAPORATION RATE : Approx. 53% (Water=1)
VOLATILES: Water
VOLATILE ORGANIC COMPOUNDS: Nil
AUTOIGNITION: Unknown
FLASH POINT: N.A.
OXIDIZING PROPERTIES: N/A
X. STABILITY AND REACTIVITY
STABILITY: Stable
NFPA REACTIVITY HAZARD CLASS: 0 = Insignificant
HAZARDOUS DECOMPOSITION PRODUCTS Carbon monoxide, carbon dioxide: Acetic acid
XI. TOXICOLOGICAL INFORMATION
CHRONIC (LONG TERM) EFFECTS OF EXPOSURE
ROUTE OF ENTRY: Skin contact; Eye contact.
EFFECTS OF CHRONIC EXPOSURE: Generally non-toxic. Use of good industrial
hygiene practices is required. Avoid direct
contact with skin or eyes. Do not ingest or
inhale.
TARGET ORGANS: Not applicable.
CARCINOGEN: No.
Not considered as hazardous.
XII. ECOLOGICAL INFORMATION
Not Available.
XIII. DISPOSAL CONSIDERATIONS
WASTE DISPOSAL METHODS: Waste disposal should be in accordance with
existing federal, state and local
environmental regulations.
EMPTY CONTAINER WARNINGS: Empty containers may contain product
residue; follow MSDS and lable warnings
even after they have been emptied.
XIV. TRANSPORTATION INFORMATION
DOT INFORMATION:
DOT SHIPPING NAME: ADHESIVE no. 1
DOT HAZARD CLASS: Non hazardous
DOT REPORTABLE QUANTITY: Not noted
IATA INFORMATION: N.A
