PAGE 1 OF 2
TECHNICAL DATA SHEET
REV20221010
GA800
Acrylonitrile Butadiene Styrene (ABS) / General Purpose
PRODUCT DESCRIPTION
GA800 is a general purpose ABS grade with glossy finish and impact resistance. It is designed for
injection molding processing such as appliance & electronic parts, automotive parts, household
goods and toys.
INDUSTRY PRODUCT FEATURE REGULATION COMPLIANCE
Appliance & Electronic Parts High Impact Strength FDA US 21 CFR 181.32
Interior Parts High Stiffness Commission Regulation (EU) 10/2011
Housewares Glossy Finish Parts RoHS Directive 2011/65/EU
Sanitary Ware REACH Regulation (EC) No. 1907/2006
Toys UL Yellow Card: E132283
EN 71-3: Safety of Toys
PHYSICAL PROPERTY TEST METHOD UNIT VALUE
Melt Flow Rate (220°C/10 kg) ASTM D1238 g/10 min 20
3
Density (23 °C) ASTM D792 g/cm 1.05
Mold Shrinkage IRPC % 0.4 - 0.6
MECHANICAL PROPERTY
Tensile Strength at Yield (3.2 mm, 5 mm/min) ASTM D638 kgf/cm 2 500
Elongation at Break (3.2 mm, 5 mm/min) ASTM D638 % 20
Flexural Strength (6.4 mm, 2.5 mm/min) ASTM D790 kgf/cm 2 700
2
Flexural Modulus (1% Secant, 6.4 mm, 2.5 mm/min) ASTM D790 kgf/cm 25,000
Izod Notched Impact Strength (6.4 mm, 23°C) ASTM D256 kgf•cm/cm 26
HARDNESS PROPERTY
Rockwell Hardness (6.4 mm) ASTM D785 R-Scale 112
THERMAL PROPERTY *Unannealed
2
Heat Distortion Temperature (6.4 mm, 18.6 kgf/cm )* ASTM D648 °C 86
Flammability (E132283) UL94 - HB (1.5 mm)
2
Conversion (1 kgf/cm = 0.098 MPa | 1 kgf•cm/cm = 9.8 J/m)
Remark: The values presented above are typical laboratory, not to be construed as specifications and may vary within moderate ranges. The applicability or accuracy of this information or the suitability of our products cannot
be guaranteed because users’ conditions of use are beyond our control.
IRPC Public Company Limited | 555/2 Energy Complex, Building B, 6th Floor, Vibhavadi Rangsit Rd., Chatuchak, Bangkok 10900 THAILAND.
HTTPS://POLIMAXX.IRPC.CO.TH TEL : +66(0) 765-7000
PAGE 2 OF 2
TECHNICAL DATA SHEET
REV20221010
GA800
Acrylonitrile Butadiene Styrene (ABS) / General Purpose
PROCESSING TECHNIQUE
Drying Temperature 80 - 85 °C
Drying Time 2 - 4 hr
Cylinder Temperature 190 - 240 °C
Mold Temperature 50 - 80 °C
Injection Pressure 30 - 80 % of maximum pressure
Holding Pressure Relative to injection pressure
Back Pressure 0 - 20% of maximum pressure
Injection Speed Low to medium of maximum pressure
*However, the actual processing conditions depend on mold design, power of machine, equipment and other environments.
PRODUCT PACKAGING
25 kg loose bag
25 kg stretch wrap on palletized
Jumbo bag
For further information, contact IRPC’s Sales repesentative.
STORAGE
The resin should be stored in a dry location with good housekeeping practices during storage, transferring and
handling. Process enclosures and adequate ventilation should be used to avoid excessive dust accumulation.
Resin should be protected from direct sunlight, temperatures above 38°C (100°F) and high atmospheric humidity
during storage. Higher storage temperatures may reduce the storage time. The container should be kept closed
to prevent contamination. For the additional recommended storage conditions, please refer to SDS.
SAFETY
This product is not classified as hazardous material for more information please refer to safety data sheet.
RECYCLING
It is an undisputed fact that the product can be recycled or disposed of without any problem.
DISCLIAMER
The data indicated above are the results of our investigations, knowledge and correspond to the state of the art as of the date of publication and the data refer to the state
of the laws at the date of issue and this information expires after a break in delivery lasting more than 12 months or in case of regulatory changes. This statement is not
intended and should not be construed as specification, warranty or representation of any sort for which IRPC would be legal responsibility. The applicability or the accuracy
of this statement or the suitable of our products cannot be guaranteed because the conditions of use on the part our uses are beyond our control. IRPC gives no guarantees
or makes no warranties which extend beyond the description above herein. Nothing herein shall constitute any implied guaranty or warranty of merchantability or fitness
for a particular purpose. In the case that IRPC's products are used in combination with other materials, no liability can be accepted. When not utilized in combination with
any third-party products, the information included above refers only to our products. Please ask IRPC for a new information if needed. All terms and conditions regarding
the supply of IRPC's products shall be subject to IRPC's Policy, in the case of a dispute, the Company's decision is final and is not subject to any appeal.
IRPC Public Company Limited | 555/2 Energy Complex, Building B, 6th Floor, Vibhavadi Rangsit Rd., Chatuchak, Bangkok 10900 THAILAND.
HTTPS://POLIMAXX.IRPC.CO.TH TEL : +66(0) 765-7000
