SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Testing & Adjusting (SENR1028-02)

SMCS - SENR10280002

P
Mechanical Troubleshooting
SP-
202 0008
Troubleshooting can be difficult. The Troubleshooting Index gives a list of possible problems. To
make a repair to a problem, make reference to the cause and correction on the pages that follow.

06: 4/01/2 379B

This list of problems, causes, and corrections will only give an indication of where a possible

4
SEN 2:33+ 4
problem can be, and what repairs are needed. Normally, more or other repair work is needed
beyond the recommendations in the list.

© 2 R102 09:00
Remember that a problem is not normally caused only by one part, but by the relation of one part
with other parts. This list is only a guide and cannot give all possible problems and corrections. The

024 8
serviceman must find the problem and its source, then make the necessary repairs.

Cat
1. Engine Crankshaft Will Not Turn When Start Switch Is On.

2. Engine Will Not Start. erp

illa
r In
3. Engine Misfires Or Runs Rough.

4. Stall At Low RPM.

5. Sudden Changes In Engine RPM.

c.
6. Not Enough Power.

7. Too Much Vibration.

8. Loud Combustion Noise.

9. Valve Train Noise (Clicking).

10. Oil In Cooling System.

11. Mechanical Noise (Knock) In Engine.

12. Fuel Consumption Too High.

13. Loud Valve Train Noise.

14. Too Much Valve Lash.

15. Valve Rotocoil Or Spring Lock Is Free.

16. Oil At The Exhaust.

17. Little Or No Valve Lash.

1 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

18. Engine Has Early Wear.

19. Coolant In Lubrication Oil.

20. Too Much Black Or Gray Smoke.

21. Too Much White Or Blue Smoke.

22. Engine Has Low Oil Pressure.

23. Engine Uses Too Much Lubrication Oil.

24. Engine Coolant Is Too Hot.

25. Exhaust Temperature Is Too High.

26. Starting Motor Does Not Turn.

27. Alternator Gives No Charge.

28. Alternator Charge Rate Is Low Or Not Regular.

29. Alternator Charge Is Too High.

30. Alternator Has Noise.

31. Rack Solenoid Does Not Stop Engine.

Troubleshooting Problems
Problem 1: Engine Crankshaft Will Not Turn When Start Switch Is On

Probable Cause:

1. Battery Has Low Output

Make Reference to Problem 26.

2. Wires Or Switches Have Defect

Make Reference to Problem 26.

3. Starting Motor Solenoid Has A Defect

Make Reference to Problem 26.

4. Starting Motor Has A Defect

Make Reference to Problem 26.

5. Inside Problem Prevents Engine Crankshaft From Turning

If the crankshaft can not be turned after the driven equipment is disconnected, remove the fuel
injection nozzles and check for fluid in the cylinders when the crankshaft is turned. If fluid in the
cylinders is not the problem, the engine must be disassembled to check for other inside problems.
Some of these inside problems are bearing seizure, piston seizure, or wrong pistons installed in the

2 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

engine.

Problem 2: Engine Will Not Start

Probable Cause:

1. Starting Motor Turns Too Slow

Make reference to Problem 27.

2. Dirty Fuel Filter

Install new fuel filter.

3. Dirty Or Broken Fuel Lines

Clean or install new fuel lines as necessary.

4. Fuel Transfer Pump

At starting rpm, the minimum fuel pressure for fuel transfer pump must be 20 kPa (3 psi). If fuel
pressure is less than 20 kPa (3 psi), change the fuel filter element. Look for air in the fuel system. If
fuel pressure is still low, install a new fuel transfer pump.

5. No Fuel To Cylinders
Put fuel in fuel tank. "Prime" (remove the air and/or poor quality fuel) the fuel system.

6. Poor Quality Fuel

Remove the fuel from the fuel tank. Install a new fuel filter element. Put a good grade of clean fuel
in the fuel tank. See Diesel Fuels and Your Engine, SEBD0717.

7. Wrong Fuel Injection Timing

Make adjustment to timing.

8. Shutoff Solenoid Will Not Move To Extended Position

The solenoid must get electricity to stop the engine. Operate the control for the shutoff solenoid and
see if the solenoid makes a noise (clicking sound). If this sound can be heard and the engine will
not start, remove the solenoid. Now see if the engine will start. If the engine starts, the shutoff
solenoid either needs an adjustment or it is defective and replacement of the solenoid is necessary.

Problem 3: Engine Misfires Or Runs Rough

Probable Cause:

1. Fuel Pressure Is Low

Make sure there is fuel in the fuel tank. Look for leaks or defective bends in the fuel line between
fuel tank and fuel transfer pump. Look for air in the fuel system. Check fuel pressure.

3 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

If fuel pressure is lower than 170 kPa (25 psi) install a new filter element. The outlet pressure of the
fuel transfer pump at full load must be 240 kPa (35 psi). If fuel pressure is still low, install a new fuel
transfer pump.

2. Air In Fuel System

Find the air leak in the fuel system and correct it. If air is in the fuel system, it will probably get in on
the suction side of fuel transfer pump.

3. Leak Or Break In Fuel Line Between Fuel Injection Pump And Fuel Injection Nozzle
Install a new fuel line.

4. Wrong Valve Lash.

Make adjustment according to the Subject, Valve Lash Setting.

5. Defect In Fuel Injection Nozzle(s) Or Fuel Injection Pump(s)

Run engine at rpm that misfires the most and runs the roughest. Then loosen a fuel line nut on the
fuel injection nozzle for each cylinder, one at a time. Find the cylinder where a loosened fuel line nut
does not change the way the engine runs. Test the fuel injection pump and fuel injection nozzle for
that cylinder. Install new parts where needed.

6. Wrong Fuel Injection Timing

Make adjustment to timing.

7. Bent Or Broken Push Rod

Replacement of push rod is necessary.

8. Fuel Has "Cloud Point" Higher Than Atmospheric Temperature ("Cloud Point"=Temperature
Which Makes Wax Form In Fuel).
Drain the fuel tank, lines, and fuel injection pump housing. Change the fuel filter. Fill the tank with
fuel which has the correct "cloud point" and remove the air from the system with the priming pump.

Problem 4: Stall At Low RPM

Probable Cause:

1. Fuel Pressure Is Low

Make sure there is fuel in the fuel tank. Look for leaks or defective bends in the fuel line between
fuel tank and fuel transfer pump. Look for air in the fuel system. Check fuel pressure.

If fuel pressure is lower than 170 kPa (25 psi) install a new filter element. The outlet pressure of the
fuel transfer pump at full load must be 240 kPa (35 psi). If fuel pressure is still low, install a new fuel
transfer pump.

2. Idle RPM Too Low

4 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Make adjustment to governor so idle rpm is the same as given in the TMI (Technical Marketing
Information) or Fuel Setting And Related Information Fiche.

3. Defect In Fuel Injection Nozzle(s)

Install a new fuel injection nozzle.

4. Engine Accessories
Check engine accessories for damage and correct adjustment. If necessary, disconnect the
accessories and test the engine.

5. Defect In Fuel Injection Pump(s)

Install new parts if needed.

Problem 5: Sudden Changes In Engine Speed (rpm)

Probable Cause:

1. Failure Of Governor Or Fuel Injection Pump

Look for damaged or broken springs, linkage or other parts. Remove the governor. Check for free
travel of fuel rack. Be sure fuel injection pumps are installed correctly. Check for correct governor
spring. Install new parts for those that have damage or defects.

Problem 6: Not Enough Power

Probable Cause:

1. Poor Quality Fuel

Remove the fuel from the fuel tank. Install a new fuel filter element. Put a good grade of clean fuel
in the fuel tank.

2. Fuel Pressure Is Low

Make sure there is fuel in the fuel tank. Look for leaks or defective bends in the fuel line between
fuel tank and fuel transfer pump. Look for air in the fuel system. Check fuel pressure.

If fuel pressure is lower than 170 kPa (25 psi) install a new filter element. The outlet pressure of the
fuel transfer pump at full load must be 240 kPa (35 psi). If fuel pressure is still low, install a new fuel
transfer pump.

3. Leaks In Air Inlet System

Check the pressure in the air inlet manifold. Look for restrictions in the air cleaner.

4. Governor Linkage
Make adjustment to get full travel of linkage. Install new parts for those that have damage or
defects.

5 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

5. Wrong Valve Lash

Make adjustment according to the Subject, Valve Lash Setting.

6. Defect In Fuel Injection Nozzle(s) Or Fuel Injection Pumps

Run engine at rpm that misfires the most or runs the roughest. Then loosen a fuel line nut on the
fuel injection pump for each cylinder, one at a time. Find the cylinder where a loosened fuel line nut
does not change the way the engine runs. Test the fuel injection pump and fuel injection nozzle for
that cylinder. Install new parts where needed.

7. Wrong Fuel Injection Timing

Make adjustment to timing.

8. Rack Setting Too Low

Make reference to the TMI (Technical Marketing Information) or Fuel Setting And Related
Information Fiche.

9. Defect In Aftercooler
Check temperature of inlet and outlet water supply. Remove any external or internal restrictions.

10. Fuel Ratio Control

Control either needs an adjustment or it is damaged and a new control is needed.

11. Turbocharger Has Carbon Deposits Or Other Causes Of Friction

Make inspection and repair of turbocharger as necessary.

Problem 7: Too Much Vibration

Probable Cause:

1. Loose Bolt Or Nut For Pulley Or Damper

Tighten bolt or nut.

2. Pulley Or Damper Has A Defect

Install a new pulley or damper.

3. Engine Supports Are Loose, Worn, Or Have A Defect

Tighten all bolts that hold engine supports. Install new components if necessary.

4. Engine Misfires Or Runs Rough

Make Reference to Problem 3.

Problem 8: Loud Combustion Noise (Sound)

Probable Cause:

6 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

1. Poor Quality Fuel

Remove the fuel from the fuel tank. Install a new fuel filter element. Put a good grade of clean fuel
in the fuel tank. See Diesel Fuels and Your Engine, SEBD0717.

2. Defect In Fuel Injection Nozzle(s)

Install new fuel injection nozzle(s).

3. Defect In Fuel Injection Pump(s)

Install new fuel injection pump(s).

4. Wrong Fuel Injection Timing

Make adjustment to timing.

Problem 9: Valve Train Noise (Clicking)

Probable Cause:

1. Damage To Valve Spring(s), Locks Or Broken Or Worn Valve Lifter

Install new parts where necessary. Broken locks can cause the valve to get into the cylinder. This
will cause much damage.

2. Not Enough Lubrication

Check lubrication in valve compartment. There must be a strong flow of oil at engine high rpm, but
only a small flow of oil at low rpm. Oil passages must be clean, especially those that send oil to the
cylinder head.

3. Too Much Valve Lash

Make adjustment according to the Subject, Valve Lash Setting

4. Damage In Bridge For Valves

Make a replacement of the bridge and make an adjustment as necessary.

Problem 10: Oil In Cooling System

Probable Cause:

1. Defect In Core Of Engine Oil Cooler

Install a new engine oil cooler.

2. Failure Of Cylinder Head Gasket Or Water Seals

Install a new head gasket and new water seals in spacer plate.

Problem 11: Mechanical Noise (Knock) In Engine

Probable Cause:

7 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

1. Failure Of Bearing For Connecting Rod

Inspect the bearing for the connecting rod and the bearing surface (journal) on the crankshaft.
Install new parts where necessary.

2. Damaged Timing Gears

Install new parts where necessary.

3. Damaged Crankshaft
Make replacement of the crankshaft.

4. Defect In Attachment
Repair or install new components.

Problem 12: Fuel Consumption Too High

Probable Cause:

1. Fuel System Leaks

Tighten or make replacement of parts at points of leakage.

2. Fuel And Combustion Noise (Knock)

Make Reference to Problem 3 and Problem 6.

3. Wrong Fuel Injection Timing

Make adjustment to timing.

Problem 13: Loud Valve Train Noise

Probable Cause:

1. Damage To Valve Spring(s)

Make replacement of parts with damage.

2. Damage To Camshaft
Make replacement of parts with damage. Clean engine thoroughly. If replacement of camshaft is
made, new valve lifters are also necessary.

3. Damage To Valve Lifter

Clean engine thoroughly. Make replacement of the damaged valve lifters. Inspect camshaft lobes
for damage. Look for valves that do not move freely. Make an adjustment to valve lash according to
the Subject, Valve Lash Setting.

4. Damage In Bridge For Valves

Make replacement of the bridge and make an adjustment as necessary.

8 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Problem 14: Too Much Valve Lash

Probable Cause:

1. Not Enough Lubrication

Check lubrication in valve compartment. There must be a strong flow of oil at engine high rpm, but
only a small flow at low rpm. Oil passages must be clean, especially those that send oil to the
cylinder head.

2. Rocker Arm Worn At Face That Makes Contact With Bridge

If there is too much wear, install new parts or rocker arms. make adjustment of valve lash according
to the Subject, Valve Lash Setting.

3. End Of Valve Stem Worn

If there is too much wear, install new valves. Make adjustment to valve lash according to the
Subject, Valve Lash Setting.

4. Bridge For Valves Worn

Make an adjustment or replacement as necessary.

5. Worn Push Rods

If there is too much wear, install new push rods. Make adjustment of valve lash according to the
Subject, Valve Lash Setting.

6. Broken Or Worn Valve Lifters

Install new valve lifters. Check camshaft for wear. Check for free movement of valves or bent valve
stem. Clean engine thoroughly. Make adjustment of valve lash according to the Subject, Valve Lash
Setting.

7. Worn Cams On Camshaft

Install a new camshaft. Install new valve lifters. Check for free movement of valves or bent valve
stems. Make adjustment of valve lash according to the Subject, Valve Lash Setting.

Problem 15: Valve Rotocoil Or Spring Lock Is Free

Probable Cause:

1. Broken Locks
Broken locks can cause the valve to get into the cylinder. This will cause much damage.

2. Broken Valve Spring(s)

Install new valve spring(s).

3. Broken Valve

9 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Replace valve and other damaged parts.

Problem 16: Oil At The Exhaust

Probable Cause:

1. Too Much Oil In the Valve Compartment

Look at both ends of the rocker arm shaft. Be sure a plug is in each end of the shaft.

2. Worn Valve Guides

Reconditioning of the cylinder head is needed.

3. Worn Piston Rings

Inspect and install new parts as needed.

Problem 17: Little Or No Valve Lash

Probable Cause:

1. Worn Valve Seat Or Face Of Valve

Reconditioning of cylinder head is needed. Make adjustment of valve lash according to the Subject,
Valve Lash Setting.

Problem 18: Engine Has Early Wear

Probable Cause:

1. Dirt In Lubrication Oil

Remove dirty lubrication oil. Install a new engine oil filter element. Put clean oil in the engine.

2. Air Inlet Leaks

Inspect all gaskets and connections. Make repairs if leaks are found.

3. Fuel Leakage Into Lubrication Oil

This will cause high fuel consumption and low engine oil pressure. Make repairs if leaks are found.
Install new parts where needed.

Problem 19: Coolant In Lubrication Oil

Probable Cause:

1. Failure Of Engine Oil Cooler Core

Install a new engine oil cooler. Drain crankcase and refill with clean lubricant. Install new engine oil
filter element.

10 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

2. Failure Of Cylinder Head Gasket Or Water Seals

Install a new cylinder head gasket and new water seals in the spacer plate. Tighten the bolts that
hold the cylinder head according to the Specifications.

3. Crack Or Defect In Cylinder Head

Install a new cylinder head.

4. Crack Or Defect In Cylinder Block

Install a new cylinder block.

5. Damaged Seals For Cylinder Liners

Make replacement of the seals.

Problem 20: Too Much Black Or Gray Smoke

Probable Cause:

1. Not Enough Air For Combustion

Check air cleaner for restrictions.

2. Defective Fuel Injection Nozzle(s)

Install new fuel injection nozzle(s).

3. Wrong Fuel Injection Timing

Make adjustment of timing.

4. Defect In Fuel Ratio Control

Make adjustment to or install new control.

Problem 21: Too Much White Or Blue Smoke

Probable Cause:

1. Too Much Lubrication Oil In Engine

Remove extra oil. Find where extra oil comes from. Put correct amount of oil in engine.

2. Engine Misfires Or Runs Rough

Make reference to Problem 3.

3. Wrong Fuel Injection Timing

Make adjustment to timing.

4. Worn Valve Guides

Reconditioning of cylinder head is needed.

11 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

5. Worn Piston Rings

Install new parts as necessary.

6. Failure Of Turbocharger Oil Seal

Check inlet manifold for oil and make repair to turbocharger if necessary.

Problem 22: Engine Has Low Oil Pressure

Probable Cause:

1. Dirty Engine Oil Filter Or Engine Oil Cooler

Install new engine oil filter. Clean or install new engine oil cooler. Remove dirty oil from engine. Put
clean oil in engine.

2. Diesel Fuel In Lubrication Oil

Find the place where diesel fuel gets into the lubrication oil. Make repairs as needed. Remove the
lubrication oil that has diesel fuel in it. Install a new engine oil filter element. Put clean oil in the
engine.

3. Too Much Clearance Between Rocker Arm Shaft And Rocker Arms
Check lubrication in valve compartment. Install new parts as necessary.

4. Engine Oil Pump Suction Pipe Has A Defect

Replacement of pipe is needed.

5. Pressure Regulating Valve Does Not Close

Clean valve and housing. Install new parts as necessary.

6. Engine Oil Pump is Worn Or Has A Defect

Repair or make replacement of necessary parts.

7. Too Much Clearance Between Crankshaft And Crankshaft Bearings

Check the engine oil filter to correct operation. Install new parts as necessary.

8. Defect In Oil Pressure Indicator

Install new indicator.

9. Too Much Bearing Clearance For Idler Gear

Inspect bearings and make replacement as necessary.

Problem 23: Engine Uses Too Much Lubrication Oil

Probable Cause:

1. Too Much Lubrication Oil In Engine

12 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Remove extra oil. Find where extra oil comes from. Put correct amount of oil in engine.

2. Oil Leaks
Find all oil leaks. Make repairs as needed.

3. Oil Temperatures Is Too High

Check operation of engine oil cooler. Install new parts if necessary. Clean the core of the engine oil
cooler.

4. Too Much Oil In The Valve Compartment

Look at both ends of the rocker arm shaft. Be sure a plug is in each end of the shaft.

5. Worn Valve Guides

Reconditioning of the cylinder head is needed.

6. Worn Piston Rings And Cylinder Liners

Inspect and install new parts as needed. Reconditioning of the cylinder block can be necessary.

7. Failure Of Seal Rings In Turbocharger

Check inlet manifold for oil and make repair to turbocharger if necessary.

Problem 24: Engine Coolant Is Too Hot

Probable Cause:

1. Restriction To Flow Of Coolant Through Radiator Core Tubes Or Heat Exchanger

Clean and flush radiator or heat exchanger.

2. Restriction To Air Flow Through Radiator

Remove all restrictions of air flow.

3. Low Fan Speed

Check for worn or loose fan belt.

4. Not Enough Coolant In System

Add coolant to cooling system.

5. Pressure Cap Has A Defect

Check operation of pressure cap. Install a new pressure cap if necessary.

6. Combustion Gases In Coolant

Find out where gases get into the cooling system. Make repairs as needed.

7. Water Temperature Regulator (Thermostat) Or Temperature Indicator Has A Defect

Check water temperature regulator for correct operation. Check temperature indicator operation.

13 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Install new parts as necessary.

8. Water Pump Has A Defect

Make repairs or replacement of the water pump as necessary. Put correct tension on drive belt for
water pump.

9. Too Much Load On The System

Make a reduction to the load.

10. Wrong Fuel Injection Timing

Make adjustment to timing.

Problem 25: Exhaust Temperature Is Too High

Probable Cause:

1. Air Inlet Or Exhaust System Has A Restriction

Remove restriction.

2. Wrong Fuel Injection Timing

Make an adjustment to the timing.

Problem 26: Starting Motor Does Not Turn

Probable Cause:

1. Battery Has Low Output

Check condition of battery. Charge battery or make replacement as necessary.

2. Wires Or Switch Has Defect

Make repairs or replacement as necessary.

3. Starting Motor Solenoid Has A Defect

Install a new solenoid.

4. Starting Motor Has A Defect

Make repair or replacement of starting motor.

Problem 27:. Alternator Gives No Charge

Probable Cause:

1. Loose Drive Belt For Alternator

Make an adjustment to put the correct tension on the drive belt.

14 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

2. Charging Or Ground Return Circuit Or Battery Connections Have A Defect

Inspect all cables and connections. Clean and tighten all connections. Make replacement of parts
with defect.

3. Brushes Have A Defect

Install new brushes.

4. Rotor (Field Coil) Has A Defect

Install a new rotor.

Problem 28: Alternator Charge Rate Is Low Or Not Regular

Probable Cause:

1. Loose Drive Belt For Alternator

Make an adjustment to put the correct tension on the drive belt.

2. Charging Or Ground Return Circuit Or Battery Connections Have A Defect

Inspect all cables and connections. Clean and tighten all connections. Make replacement of parts
with defects.

3. Alternator Regulator Has A Defect

Install a new alternator regulator.

4. Alternator Brushes Have A Defect

Install new brushes.

5. Rectifier Diodes Have A Defect

Make replacement of rectifier diode that has a defect.

6. Rotor (Field Coil) Has A Defect

Install a new rotor.

Problem 29: Alternator Charge Is Too High

Probable Cause:

1. Alternator Or Alternator Regulator Has Loose Connections

Tighten all connections to alternator or alternator regulator.

2. Alternator Regulator Has A Defect

Install a new alternator regulator.

Problem 30: Alternator Has Noise

15 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Probable Cause:

1. Drive Belt For Alternator Is Worn Or Has A Defect

Install a new drive belt for the alternator.

2. Loose Alternator Drive Pulley

Check groove in pulley for key that holds pulley in place. If groove is worn, install a new pulley.
Tighten pulley nut according to Specifications.

3. Drive Belt And Drive Pulley For Alternator Are Not In Alignment
Make an adjustment to put drive belt and drive pulley in correct alignment.

4. Worn Alternator Bearings

Install new bearings in the alternator.

5. Rotor Shaft Is Bent

Make replacement of the rotor shaft.

6. Rectifiers In The Alternator Are Shorted

Make replacement of the diode assembly.

Problem 31: Rack Solenoid Does Not Stop Engine

Probable Cause:

1. Electrical Connections Are Not Correct

Correct electrical connections and wiring.

2. Adjustment for Plunger Shaft Is Not Correct

Make an adjustment to the plunger shaft.

3. Wrong Plunger In Solenoid

Install the correct plunger in the solenoid.

4. Not Enough Plunger Travel

Make an adjustment to the plunger shaft or make replacement of the solenoid if necessary.

5. Defect In Solenoid Wiring

Make replacement of the solenoid.

Fuel System
Either too much fuel or not enough fuel for combustion can be the cause of a problem in the fuel
system. Many times work is done on the fuel system when the problem is really with some other

16 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

part of the engine. The source of the problem is difficult to find, especially when smoke comes from
the exhaust. Smoke that comes from the exhaust can be caused by a defective fuel injector, but it
can also be caused by one or more of the reasons that follow:

a. Not enough air for good combustion.

b. An overload at high altitude.

c. Oil leakage into combustion chamber.

d. Not enough compression.

e. Fuel injection timing incorrect.

Fuel System Inspection

A problem with the components that send fuel to the engine can cause low fuel pressure. This can
decrease engine performance.

1. Check the fuel level in the fuel tank. Look at the cap for the fuel tank to make sure the vent is not
filled with dirt.

2. Check the fuel lines for fuel leakage. Be sure the fuel supply line does not have a restriction or a
defective bend. Verify that the fuel return line has not collapsed in the sections subject to heat.

3. Install a new fuel filter. Clean the primary fuel filter.

4. To remove air from the fuel system, use the procedure that follows:

a. Use the priming pump to remove air from the low pressure side of the fuel system.

b. Loosen one-half turn the fuel injection line nuts at each adapter in the valve cover base. Move
throttle lever to Low Idle position. Use the starting motor to turn the engine until fuel without air
flows from the loose connections. Tighten the nuts.

NOTE: Because of the check assemblies in the fuel injection pump outlets the priming pump will not
give enough pressure to remove air from the fuel injection lines.

5. Inspect the fuel bypass valve to see that there is no restriction to good operation.

Fuel Transfer Pump

With the engine operating at full load speed, the fuel transfer pump moves fuel through the
secondary filter and the fuel injection pump housing at approximately 240 kPa (35 psi).

To check the fuel transfer pump pressure, disconnect the fuel line (from the filter) at the fuel
injection pump housing inlet. Install a tee at the inlet and connect the fuel line to the tee. Connect a

17 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

pressure indicator to the tee and start the engine.

Minimum fuel pressures must be 70 kPa (10 psi) at low idle and 170 kPa (25 psi) at full load speed
(and engine under full load).

If the fuel pressure is not above the minimum specifications, stop the engine. Make a replacement
of the primary and secondary fuel filters and check to make sure the fuel lines and hoses are not
plugged or damaged.

Start the engine and again check the fuel pressure. If the fuel pressure is not above the minimum
specification, a repair or replacement of the fuel transfer pump is needed.

Checking Engine Cylinders Separately

An easy check can be made to find the cylinder that runs rough (misfires) and causes black smoke
to come out of the exhaust pipe.

Run the engine at the speed that is the roughest. Loosen the fuel line nut at a fuel injection pump.
This will stop the flow of fuel to that cylinder. Do this for each cylinder until a loosened fuel line is
found that makes no difference in engine performance. Be sure to tighten each fuel line nut after the
test, before the next fuel line nut is loosened. Check each cylinder by this method. When a cylinder
is found where the loosened fuel line nut does not make a difference in engine performance, test
the fuel injection pump and fuel injection nozzle for that cylinder.

Temperature of an exhaust manifold port, when the engine runs at low idle speed, can also be an
indication of the condition of a fuel injection nozzle. Low temperature at an exhaust manifold port is
an indication of no fuel to the cylinder. This can possibly be an indication of an fuel injection nozzle
with a defect. Extra high temperature at an exhaust manifold port can be an indication of too much
fuel to the cylinder, also caused by an fuel injection nozzle with a defect.

The most common defects found with the fuel injection nozzle are:

1. Carbon on tip of the fuel injection nozzle or in the fuel injection nozzle orifice.

2. Steel wire brushing of fuel injection tip.

3. Orifice wear.

4. Dirty fuel injection nozzle screen.

Testing Fuel Injection Nozzles

Testing of the fuel injection nozzles must be done off the engine. Perform the following tests using
the 5P4150 Nozzle Testing Group to determine if nozzle performance is acceptable:

18 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Valve Opening Pressure Test

Flush The Nozzle

Tip Leakage Test

Orifice Restriction Test

Bleed Screw Leakage Test

Refer to Special Instruction SEHS7292, for operation of the 5P4150 Nozzle Testing Group.

Fuel Injection Lines

Fuel Injections Lines With Support Bracket

(1) A vertical line through the number one fuel injection pump.

The nuts that hold a fuel injection line to a fuel injection pump must be tightened to the correct
torque. If the nut is loose, fuel will leak from the connection. If the nut is tightened too tight, the
inside diameter of the line will become smaller and cause a restriction to the flow of fuel in the line.
Use a torque wrench and a 5P0144 Fuel Line Socket to tighten the fuel injection line nuts to 42 ± 7
N·m (31 ± 5 lb ft).

19 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Be sure the fuel injection line clamps are installed in the correct
location. Incorrectly installed clamps may allow the fuel
injection lines to vibrate and become damaged. The damaged
lines may leak and cause a fire.

NOTE: Align brackets in position to fuel lines such that when the fasteners are tightened no strain
will be added to the fuel lines while tightening fasteners.

Checking The Plunger And Lifter Of An Fuel Injection

Pump
NOTE: There are no different size spacers available to adjust the timing dimension of the fuel
injection pumps. If the pump plunger or the lifter is worn, they must be replaced. Because there is
no adjustment to the timing dimension possible, there is No Off Engine Lifter Setting Procedure.

When there is too much wear on the fuel injection pump plunger, the lifter may also be worn and
there will not be good contact between the two parts. To stop fast wear on the end of a new plunger,
install new lifters in the place of the lifters that have wear.

Wear Between Lifter And Plunger

Figure A illustrates the contact surfaces of a new pump plunger and new lifter. In Figure B the pump plunger and lifter have
worn considerably. Figure C shows how the flat end of a new plunger makes poor contact with a worn lifter, resulting in
rapid wear to both parts.
A fuel injection pump can have a good fuel flow coming from it but not be a good pump because of
slow timing that is caused by wear on the bottom end of the plunger. When making a test on a
pump that has been used for a long time, use a micrometer and measure the length of the plunger.

20 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

If the length of the plunger is shorter than the minimum length (worn) dimension given in the chart
install a new pump.

Look for wear at the top part of the plunger. Check the operation of the plunger according to the
instructions for the Fuel Injection Test Bench.

Removal And Installation Of Fuel Injection Pumps

This procedure can be done with the fuel injection pump housing on or off the engine.

Before the 6V7050 Compressor Group is used for the first time, or if the group has been
disassembled, make the following adjustment:

1. An fuel injection pump that is to be used for this adjustment (or one that is to be removed or
installed) must have another fuel injection pump installed next to it. The second fuel injection pump
serves as the compressor mounting stud. If there are not two fuel injection pumps next to each
other, install two fuel injection pumps without the lifter springs. See Installation Of Fuel Injection
Pumps for the correct alignment of the pump at assembly.

21 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Adjustment of 6V7050 Compressor Group

(A) 6V7015 Clamp.

(B) Bracket assembly.

(C) 4B2046 Nut.

(D) 8T0937 Nut.

(E) 2N3476 Screw.

2. Put bracket assembly (B) over one of the pump bonnets.

3. Put the clamp ram on the center of the other fuel injection pump bonnet with 2N3476 Screw (E)
in contact with the fuel line seat.

NOTE: The 6V7015 Clamp (A) should not be locked down.

4. Install and tighten 8T0937 Nut (D).

5. Adjust screw in or out until the top of bracket assembly (B) just starts to move when the clamp
ram is locked down.

6. Tighten 4B2046 Nut (C) to hold 2N3476 Screw (E) in position.

Removal Of Fuel Injection Pumps

NOTICE

Before any parts are removed from the fuel injection pump
housing, thoroughly clean all dirt from the housing. Dirt that
gets inside the pump housing will cause much damage.

NOTE: The fuel rack must be in the zero (center) position before the fuel injection pumps can be
removed or installed. Follow Steps 1 through 5.

22 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Fuel Injection Pump Housing

(1) Plug (rack centering pin).

(2) Cover (rack position indicator).

1. Remove plug (1) and cover (2) from the fuel injection pump housing.

Fuel Rack Against Timing Pin in the Zero Position

(3) 6V4186 Timing Pin.

2. Install the 6V4186 Timing Pin (3) in the top of the fuel injection pump housing. Make sure 6V4186
Timing Pin (3) engages in the slot of the fuel rack as shown.

Holding Fuel Rack in Zero Position

(3) 6V4186 Timing Pin.

(4) 8T9198 Bracket Assembly.

(5) 1U5426 Compressor Assembly.

3. Install 8T9198 Bracket Assembly (4) on the fuel injection pump housing. Make sure the lever of
the bracket assembly is engaged in the slot of the fuel rack.

4. Install the 1U5426 Compressor Assembly (5) all the way into the 8T9198 Bracket Assembly (4) to
compress the spring.

23 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

5. Tighten the collet on 6V4186 Bracket Assembly (4) to hold 1U5426 Compressor Assembly (5).
Spring force now holds the fuel rack against 6V4186 Timing Pin (3) in the zero position.

Fuel Injection Pump Housing

(3) 6V4186 Timing Pin.

(6) 8T5287 Wrench.

(7) 6V7050 Compressor Group.

(8) Retainer bushing.

6. Remove the fuel injection line from the pump to be removed and also the fuel injection lines on
each side of the pump to be removed.

There is spring force on the fuel injection pump plunger and

barrel assembly. Removal of retainer bushing (8) without the
6V7050 Compressor Group correctly installed can cause bodily
injury.

7. Use 8T5287 Wrench (6) to loosen retainer bushing (8) one quarter turn. Do not remove the
bushing at this time.

8. Install 6V7050 Compressor Group (7) on the pump housing over 8T5287 Wrench (6). Lower the
screw in the compressor ram to the fuel line seat before the nut is tightened to hold the compressor
group in position. This centers the compressor group.

Fuel Injection Pump Housing

24 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

(3) 6V4186 Timing Pin.

(6) 8T5287 Wrench.

(7) 6V7050 Compressor Group.

(8) Retainer bushing.

9. Use 8T5287 Wrench (6) to loosen retainer bushing (8) until it is out of the threads. Slowly raise
the compressor tool handle to release the spring force.

Fuel Injection Pump Housing

(9) 8S2244 Extractor.

10. Remove the 6V7050 Compressor Group and the 8T5287 Wrench. Install 8S2244 Extractor (9)
on the fuel injection pump threads. Carefully pull the pump straight up and out of the pump housing
bore. Remove the spacer from the pump housing bore.

Be careful when an fuel injection pump is disassembled. Do not damage the surface on the plunger.
The plunger and barrel are made as a set. Do not put the plunger of one pump in the barrel of
another pump. If one part is worn, install a complete new pump assembly. Be careful when the
plunger is put into the bore of the barrel. When fuel injection pumps are removed from the fuel
injection pump housing, keep the parts together so they can be installed in the same location in the
housing.

Installation Of Fuel Injection Pump

NOTICE

The fuel rack Must Be In The Center Position before the correct
installation of an fuel injection pump is possible.

1. Put the fuel rack in the center position. See Removal of Fuel Injection Pumps for this procedure.

25 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Fuel Injection Pump Installation

(1) 8S2244 Extractor.

(2) Pump barrel.

(3) Gear segment.

2. Put 8S2244 Extractor (1) on the threads of the fuel injection pump.

3. Make sure the lifter for the pump to be installed is at the bottom of its travel (cam lobe is at its
lowest point).

4. Put the groove in pump barrel (2) in alignment with the slot (groove) in gear segment (3).

5. Be sure the spacer is in position in the pump housing bore.

Fuel Injection Pump Housing (Top View)

(4) Pin.

(5) Dowel.

6. Carefully install the pump straight down into the pump housing bore.

NOTE: The slot (groove) in gear segment (3) must be in alignment with pin (4) in the side of the
lifter and the groove in pump barrel (2) must be in alignment with dowel (5) in the housing bore.

26 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Fuel Injection Pump Housing

(6) 6V4186 Timing Pin.

(7) 8T5287 Wrench.

(8) 6V7050 Compressor Group.

(9) Retainer bushing.

7. Remove the 8S2244 Extractor. Put the O-ring seal, retainer bushing (9) and 8T5287 Wrench (7)
in position on the top of the fuel injection pump. Install 6V7050 Compressor Group (8).

8. Slowly move the handle of the 6V7050 Compressor Group down to push the fuel injection pump
into the bore.

NOTICE

The handle of the 6V7050 Compressor Group must move

smoothly down to the lock position. Do not force the handle if it
stops. If the handle does not move smoothly down to the lock
position, raise the handle, remove the 6V7050 Compressor
Group, and repeat Steps 3 through 8.

9. Put the O-ring seal in position in the pump housing bore. Use the 8T5287 Wrench to install the
retainer bushing.

10. Remove the 6V7050 Compressor Group. Tighten the retainer bushing to 270 ± 13 N·m (200 ±
10 lb ft).

NOTICE

The bushing must be tightened to the correct torque. Damage to

the housing will be the result if the bushing is too tight. If the
bushing is not tight enough, the pump will have leakage.

11. Install the fuel injection lines to the pump and tighten to 42 ± 7 N·m (31 ± 5 lb ft). See Fuel
Injection lines in this section for more information.

27 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Be sure the fuel injection line clamps are installed in the correct
locations. Incorrectly installed clamps may allow the fuel
injection lines to vibrate and become damaged. The damaged
lines may leak and cause a fire.

The following steps can be used to insure correct installation and operation of any number of
individual replacement pumps on most machine engines.

12. Remove or activate the shutoff solenoid if it is installed in the rack actuator housing.

NOTE: The manual shutoff override lever can be used to move the shutoff solenoid out of the way
so the fuel rack can be moved.

NOTE: To check the installation of a replacement pump, it is necessary to have full rack travel in
both directions. The actual zero location of the timing pin and rack are not used to check the
installation of replacement pumps.

Check Fuel Rack Travel

(6) 6V4186 Timing Pin.

(10) 8T9198 Bracket Assembly.

13. Remove the compressor and 8T9198 Bracket Assembly (10) from the fuel injection pump
housing.

28 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Illustration 1. Correct installation in full load position.

14. Raise the timing pin and move the rack to the full load position. Use finger pressure to be sure
the rack is at full rack travel (beyond full load position).

15. If the fuel injection pump installation is correct, when the timing pin is lowered it will be on the
rack as shown in Illustration 1.

Illustration 2. Incorrect installation, full load position restricted by less than full rack travel.
16. If the fuel injection pump installation is not correct, the timing pin position will be approximately
1.91 mm (.075 in) toward the slot for each tooth position out of alignment (see Illustration 2). This
will reduce fuel rack travel, even though it may not affect the rack setting, because of additional rack
travel at static conditions.

29 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Illustration 3. Correct installation at no load (fuel off) position.

17. Raise the timing pin and move the rack to the no load (fuel off) position.

18. If the fuel injection pump installation is correct, when the timing pin is lowered it will be in the
timing slot, less than 1.91 mm (.075 in) from the rear face of the slot as shown in Illustration 3.

Illustration 4. Incorrect installation, fuel shutoff position restricted by less than full rack travel.
19. If the fuel injection pump installation is not correct, the timing pin position will be more than 1.91
mm (.075 in) from the rear face of the timing slot in the rack (see Illustration 4).

20. When all fuel injection replacement pumps are installed correctly remove 6V4186 Timing Pin (6)
from the fuel injection pump housing and install the plug.

30 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

21. Install the gasket and cover over the fuel rack on the side of the fuel injection pump housing.

NOTICE

If one or more of the fuel injection pumps have been installed

wrong, it is possible for the engine to run out of control when
started. When any of the fuel injection pumps have been
removed and installed with the fuel injection pump housing on
the engine, take the precautions (steps) that follow to stop the
engine if it starts to overspeed (run out of control).

Turbocharger Air Inlet Opening

a. Remove the air cleaner pipe from the turbocharger leaving the air inlet open as shown.

b. Set the governor control at low idle. No pressure applied to the accelerator pedal (up).

Stopping The Engine

c. Start the engine, and if engine starts to overspeed (run out of control), put a steel plate over the
air inlet as shown to stop the engine.

31 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Be careful when plate is put against air inlet opening. Due to

excessive suction, the plate can be pulled quickly against air
inlet opening. To avoid crushed fingers, do not put fingers
between plate and air inlet opening.

Finding Top Center Compression Position For No. 1

Piston

No. 1 piston at top center (TC) on the compression stroke is the starting point of all timing
procedures.

NOTE: On some engines there are two threaded holes in the flywheel. These holes are in
alignment with the holes with plugs in the left and right front of the flywheel housing. The two holes
in the flywheel are at a different distance from the center of the flywheel so the timing bolt cannot be
put in the wrong hole.

Locating Top Center (Left Side of Engine)

(1) Timing bolt.

(2) Location (timing bolt).

(3) Storage location.

32 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Locating Top Center (Right Side of Engine)

(4) Location (timing bolt).

1. The timing bolt (1) is kept in storage location (3) and can be installed in either the left side of the
engine at location (2) or in the right side of the engine at location (4). Remove bolts and cover from
flywheel housing. Remove the plug from the timing hole in the flywheel housing.

Using 9S9082 Engine Turning Tool

(1) Timing bolt.

(5) 9S9082 Engine Turning Tool.

2. Put timing bolt (1) [long bolt that holds cover on the flywheel housing] through the timing hole in
the flywheel housing. Use the 9S9082 Engine Turning Tool and 1/2 inch drive ratchet wrench to turn
the engine flywheel in the direction of normal engine rotation until the timing bolt engages with the
threaded hole in the flywheel.

NOTE: If the flywheel must be turned opposite normal engine rotation approximately 45 degrees.
Then turn the flywheel in the direction of normal rotation until the timing bolt engages with the
threaded hole. The reason for this procedure is to make sure the play is removed from the gears
when the No. 1 piston is put on top center.

3. Remove the front valve cover from the engine.

Checking No. 1 Inlet And Exhaust Valves

4. The inlet and exhaust valves for the No. 1 cylinder are closed if No. 1 piston is on the
compression stroke and the rocker arms can be moved by hand. If the rocker arms can not be
moved and the valves are slightly open the flywheel must be turned again. Remove the timing bolt
and turn the flywheel in the direction of normal engine rotation 360 degrees until the timing bolt can
be installed. The No. 1 piston is now in the top center compression position.

33 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Checking Engine Timing With 8T5300 Timing Indicator

Group And 8T5301 Diesel Timing Adapter Group

8T5300 Timing Indicator Group

(1) 8T5250 Engine Timing Indicator.

(2) 5P7366 Cable Assembly.

(3) 6V2197 Magnetic Transducer.

(4) 5P7362 Cable.

(5) 6V2199 and 6V3093 Transducer Adapters.

(6) 8K4644 Fuse.

The 8T5300 Timing Indicator Group must be used with the 8T5301 Diesel Timing Adapter Group.

8T5301 Diesel Timing Adapter Group

(7) 5P7437 Adapter.

(8) 6V2198 Cable.

(9) 5P7436 Adapter.

(10) 6V7910 Transducer.

(11) 5P7435 Adapter.

(12) 6V3016 Washer.

34 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

A high pressure fuel line must be disconnected. To avoid

personal injury or fire from fuel spray, the engine must be
stopped before the fuel line is disconnected.

When checking the dynamic timing on an engine without a mechanical advance, Caterpillar
recommends that the service personnel calculate and graph the dynamic timing on a worksheet like
SEHS8140. These worksheets are available in pads of 50 sheets, order one SEHS8140. See
Special Instruction SEHS8580, for information required to calculate the timing curve.

After the timing values are calculated and plotted, the dynamic timing should be checked with the
8T5300 Engine Timing Indicator Group. To do this, the service personnel must operate the engine
from 1000 rpm (base rpm) to high idle and from high idle to 1000 rpm (base rpm). Unstable
readings are often obtained below 1000 rpm. They must record the dynamic timing at each 100 rpm
and at the specified speeds during both acceleration and deceleration. Then they should plot the
results on the worksheet.

Inspection of the plotted value will show if the timing is within specifications. See Special Instruction
SEHS8580 for information required to calculate the timing.

1. See the Engine Information Plate for the performance specification number and make reference
to the TMI (Technical Marketing Information) or Fuel Setting And Related Information Fiche for the
correct timing specifications to use.

2. Make reference to Operation Instructions inside the lid of the 8T5300 Timing Indicator (1) or
Special Instruction SEHS8580 for complete instructions and calibration.

The engine must be stopped before the timing indicator group is

installed. A high pressure fuel line must be disconnected and a
probe must be installed against the flywheel.

35 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Transducer In Position (Typical Example)

(10) Injection transducer.

(13) Fuel injection line (for No. 6 cylinder).

3. Loosen all fuel line clamps that hold No. 1 fuel injection line, and disconnect fuel injection line
(13) for the No. 1 cylinder at the fuel injection pump. Slide the nut up and out of the way. Put
5P7436 Adapter (9) in its place and turn adapter (9) onto the fuel pump bonnet until the top of the
bonnet threads are approximately even with the bottom of the "window" in the adapter.

4. Put the 5P7435 Tee Adapter (11) on the injection transducer (10), and put the end of the 5P7435
Tee Adapter (11) in the "window" of the 5P7436 Adapter (9).

5. Put fuel injection line (13) on top of 5P7435 Tee Adapter (11). Install 5P7437 Adapter (7), and
tighten to 42 N·m (31 lb ft).

6. Remove the plug from the flywheel housing. Install transducer adapter (5) into the hole the plug
was removed from. Tighten only a small amount.

Transducer In Position
(3) Magnetic transducer.

(5) Transducer adapter.

7. Push magnetic transducer (3) into the pipe adapter (5) until it makes contact with the flywheel.
Pull it back out 1.5 mm (.06 in) and lightly tighten the knurled locknut.

8. Connect the cables from the transducers to Engine Timing Indicator (1). Calibrate and make
adjustments. For calibration procedure, make reference to Special Instruction SEHS8580.

9. Start the engine, and let it reach operating temperature. Then run the engine at approximately

36 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

one-half throttle for eight to ten minutes before measuring timing.

10. Run the engine at the speeds required, and record the timing indicator readings. If the engine
timing is not correct, make reference to Checking Engine Timing By Timing Pin Method for static
adjustment of the fuel injection pump drive. If the timing advance is not correct, do the steps that
follow to make an adjustment.

Typical Illustration Front Of Engine

(14) Access cover (for governor and fuel pump drive group).

11. Stop the engine and remove access cover (14).

Typical Illustration Automatic Timing Advance Unit

(15) Locknut.

(16) Screw.

(17) Screw.

(18) Setscrew [located inside of screw (17)].

12. If the adjustments are being made because of an engine horsepower rating change of for
replacement of parts, start with an initial setting as follows:

a. Adjustment screw (16) must extend out from the retainer approximately 27.9 mm (1.10 in).

b. Setscrew (18) must be below the end of screw (17) approximately 17.78 mm (.700 in) on an
engine with 11 degrees timing advance and 19.05 mm (.750 in) on an engine with 10 degree timing
advance.

13. To adjust the speed where the fuel injection timing starts to advance, loosen locknut (15) and
turn screw (16). Turn screw (16) clockwise to increase the speed where the timing advance starts.
Tighten locknut (15) to a torque of 70 ± 15 N·m (50 ± 11 lb ft).

37 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

(19) 6V2106 Tool Group.

NOTE: If the speed where timing advance starts is adjusted, the speed where the automatic timing
advance should also be adjusted.

14. To adjust the speed where the fuel injection automatic timing advance stops, loosen locknut (15)
and turn setscrew (18) clockwise to decrease the stop speed. Tighten locknut (15) to a torque of
2.25 ± 0.25 N·m (20 ± 2 lb in). 6V2106 Tool Group (19) [part of 6V6070 Governor Adjusting Tool
Group] can be used to make this adjustment.

15. After each adjustment, install access cover (14) and recheck the automatic timing advance with
the 8T5300 Timing Indicator Group.

16. If the automatic timing advance unit cannot be adjusted to operate within the correct range, or
the operation of the unit is not smooth, repair or replace the automatic timing advance unit
(governor and fuel pump drive group).

Checking Engine Timing By Timing Pin Method

Mechanical Timing Advanced Units

1. Put No. 1 piston at top center on the compression stroke. Make reference to Finding Top Center
Compression Position For No. 1 Piston. Remove the timing bolt from the flywheel and use 9S9082
Engine Turning Tool to rotate the crankshaft clockwise 45 degrees as seen from the flywheel end of
the engine.

38 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Fuel Injection Pump

(1) Plug (timing pin hole).

2. Remove plug (1) from the fuel injection pump housing.

Timing Pin Installed

(2) 6V4186 Timing Pin.

3. Install 6V4186 Timing Pin (2) in the fuel injection pump housing as shown. Slowly rotate the
crankshaft counterclockwise (as seen from the flywheel end of the engine) until 6V4186 Timing Pin
(2) goes into the slot in the fuel pump camshaft.

NOTICE

Too much pressure on the timing pin can damage the fuel
injection pump or the timing pin.

4. Put the timing bolt in the timing hole in the flywheel housing. Rotate the crankshaft
counterclockwise (as seen from the flywheel end of the engine) until the fuel pump camshaft is tight
against 6V4186 Timing Pin (2). This removes gear clearance from the drive train. If the bolt can be
installed in the timing hole in the flywheel, the timing of the fuel injection is correct.

39 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Front Of Engine
(3) Access cover (for governor and fuel pump drive group).

5. If the timing bolt does not go into the timing hole in the flywheel, the timing is not correct. Do the
steps that follow to adjust the fuel injection pump timing.

a. Remove access cover (3).

Governor And Fuel Pump Drive Group

(3) Access cover.

(4) Bolts.

b. Loosen eight bolts (4). With 6V4186 Timing Pin (2) installed and the timing bolt removed, turn the
flywheel clockwise (opposite the direction of engine rotation) a minimum of 45 degrees. The reason
for this step is to remove play from the timing gears when the engine is put on top center (TC).

c. Tighten two bolts (4) 180 degrees apart, evenly to a torque of 3 N·m (27 lb in). This puts a slight

40 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

clamping force on the gear for the next step.

d. Turn the flywheel slowly in the direction of engine rotation until the timing bolt can be installed in
the flywheel. The number one piston is now at top center (TC).
NOTE: The crankshaft can be turned from the front of the engine by using a wrench on the vibration
damper bolts, if necessary.

e. Tighten eight bolts (4) to a torque of 55 ± 10 N·m (40 ± 7 lb ft). Remove the timing bolt from the
flywheel and 6V4186 Timing Pin (2) from the fuel injection pump housing.

6. Turn the flywheel clockwise (opposite the direction of normal engine rotation) a minimum of 45
degrees. Now, turn the flywheel in the direction of engine rotation until 6V4186 Timing Pin (2) drops
into slot of pump camshaft. Now turn the flywheel more, in the direction of normal engine rotation,
until all gear clearance is removed from the drive train. Check to see that the timing bolt will go into
the flywheel.

7. If the timing is not correct, do the procedure of Steps 5b through 5e again.

8. If the timing is correct, remove the timing bolt from the flywheel and timing pin from the fuel
injection pump housing. Install access cover (3) and plug (1).

Automatic Timing Advance Units

1. Put No. 1 piston at top center on the compression stroke. Make reference to Finding Top Center
Compression Position For No. 1 Piston. Remove the timing bolt from the flywheel and use 9S9082
Engine Turning Tool to rotate the crankshaft clockwise 45 degrees as seen from the flywheel end of
the engine.

NOTE: The crankshaft can be turned from the front of the engine by using a wrench on the vibration
damper bolts, if necessary.

41 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Front Of Engine (Typical Examine)

(1) Access cover [for automatic timing advance (governor and fuel pump drive group)].

2. Remove timing advance access cover (1).

Automatic Timing Advance Unit

(2) Retainer.

(3) Nuts.

(4) Bolts.

3. Loosen nuts (3) and remove retainer (2) and the flyweight spring from the timing advance unit.
Make sure that the flyweight spring does not fall out and get lost.

NOTE: Do not loosen the locknuts and adjustment screws in the end of retainer (2). If the
adjustment screws are moved from their original settings, the dynamic engine timing must be set by
using the 8T5300 Timing Indicator Group after the static timing pin procedure is completed.

4. Loosen bolts (4) that hold the timing advance unit together.

5. Tighten bolts (4) to a torque of 1.8 ± 0.3 N·m (16 ± 3 lb in). This puts a slight clamping force on
the fuel pump drive gear to hold it in position. Also, the fuel pump camshaft can be turned or held in
position separate from the engine crankshaft. The drive gear is allowed to slip.

42 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Fuel Injection Pump

(5) Plug (timing pin hole).

6. Remove plug (5) from the fuel injection pump housing.

Timing Pin Installed

(6) 6V4186 Timing Pin.

7. With No. 1 piston 45 degrees before Top Center, slowly rotate the crankshaft counterclockwise
(as seen from the flywheel end of the engine) until 6V4186 Timing Pin (6) goes into the slot in the
fuel pump camshaft and the timing bolt can be installed in the timing hole in the flywheel.

Install Holding Tool

(3) Nut.

(7) 1U8271 Holding Tool.

8. Install the 1U8271 Holding Tool (7) and push the timing advance unit piston back as follows:

a. Turn the knurled nuts on the holding tool out until each stud is 6.4 mm (.25 in) below the surface
of the nut.

b. Put 1U8271 Holding Tool (7) in position on the cap screws that hold retainer (2). Install and
tighten nuts (3) finger tight. Make sure that the four tangs on the loose inner ring of the holder tool
are positioned at the corners of the four flyweights and flyweights are free to move.

c. Tighten the four large knurled nuts evenly by hand until a positive stop is felt. No external
component contact can be seen. The positive stop is the timing advance piston making contact at
the bottom of its travel. This step makes sure that the timing advance unit is in its most retarded
timing position.

43 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Tighten Drive Bolts And Remove Tooling

(4) Bolts.

9. Tighten the four bolts (4) to a torque of 55 ± 7 N·m (41 ± 5 lb ft).

10. Remove holding tool from the automatic timing advance unit.

11. Remove the timing pin bolt from the flywheel and 6V4186 Timing Pin (6) from the fuel injection
pump housing.

12. Install the flyweight spring and retainer (2) on the timing advance unit. Make sure the spring is in
its correct position and tighten the four nuts to hold the retainer in position.

13. Install access cover (1) on the timing gear housing and plug (5) in the fuel injection pump
housing.

14. If necessary, check the dynamic timing of the engine with the 8T5300 and 8T5301 Tool Groups.
Make reference to Special Instructions SEHS8580, for the correct installation and operation of the
tool groups. Also, see Checking Engine Timing With 8T5300 Timing Indicator Group And 8T5301
Diesel Timing Adapter Group for the procedure to check the dynamic timing of the engine.

Fuel Setting Procedure

44 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

6V6070 Governor Adjusting Tool Group

NOTE: If the 8T1000 Electronic Position Indicator Group is used, make reference to Special
Instruction SEHS8623 for information on the use of the tool group.

The fuel setting procedure can be used with the fuel injection pump and governor on or off the
engine.

Fuel Injection Pump And Governor

(1) Cover (rack position indicator).

(2) Plug (rack centering pin).

1. Remove plug (2) and cover (1) from the fuel injection pump housing.

Indicator And Centering Pin Installed

(3) 6V4186 Timing Pin.

(4) 6V6109 Bracket Assembly.

(5) 2A0762 Bolt (1/4-20 NC X .625 in).

(6) 8H9178 Ground Body Bolt (1/4-20 NC X 1.00 in).

(7) 5P4814 Collet.

(8) 6V6106 Dial Indicator.

NOTE: If the 8T1000 Position Indicator Group is used instead of the dial indicator, use Step 3 for
the installation of the probe.

2. Install the rack position indicator as follows:

a. Install the 5P4814 Collet (7) on the 6V6109 Bracket Assembly (4).

45 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Slot In Fuel Injection Pump Rack

(9) Slot.

b. Position the indicator arm in approximately the middle of its travel to make sure that it will engage
in slot (9) in the rack. Put 6V6109 Bracket Assembly (4) in position on the fuel injection pump
housing.

c. Install 8H9178 Ground Body Bolt (6) first. Then install 2A0762 Bolt (5).

d. Be sure the indicator arm moves freely.

e. Put 6V6106 Dial Indicator (8) in position in 5P4814 Collet (7).

f. Put the 9S8903 Contact Point on the 6V2030 Extension and install on 6V6106 Dial Indicator (8).
NOTE: The 9S8903 Contact Point will not go through the collet and must be assembled after the
indicator stem has passed through the collet.

g. Tighten 5P4814 Collet (7) just enough to hold the dial indicator.

3. Install the rack position probe as follows:

a. Install the 5P4814 Collet (7) on the 6V6109 Bracket Assembly (4).

b. Position the indicator arm in approximately the middle of its travel to make sure that it will engage
in slot (9) in the rack. Put 6V6109 Bracket Assembly (4) in position on the fuel injection pump
housing.

c. Install 8H9178 Ground Body Bolt (6) first. Then install 2A0762 Bolt (5).

d. Be sure the indicator arm moves freely.

e. Put probe (A) in position in 5P4814 Collet (7).

f. Put the 9S8903 Contact Point on the 6V2030 Extension and install on probe (A).
NOTE: The 9S8903 Contact Point will not go through the collet and must be assembled after the
indicator stem has passed through the collet.

g. Adjust probe (A) in 5P4814 Collet (7) so that the shaft can be moved through the entire
measurement range without reaching the end of the shaft travel. Tighten the collet.

46 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Probe And Centering Pin Installed

(3) 6V4186 Timing Pin.

(4) 6V6109 Bracket Assembly.

(5) 2A0762 Bolt (1/4-20 NC X .625 in).

(6) 8H9178 Ground Body Bolt. (1/4-20 NC X 1.00 in).

(7) 5P4814 Collet.

(A) 8T1002 Probe.

Position Fuel Injection Pump Rack

(10) 6V6151 Adapter.

(11) 6V7942 Hook

4. Remove the shutoff solenoid, if equipped, or cover and install the 6V6151 Adapter (10).

5. Move the governor control lever to the "LOW IDLE" position (rotate governor shaft
counterclockwise).

6. Install the 6V4186 Timing Pin (3) in the top of the fuel injection pump housing. Push the timing
pin in until contact with the fuel rack is made.

7. Use 6V7942 Hook (11) through 6V6151 Adapter (10) to push the sleeve and rack to the
"SHUTOFF" position. Make sure 6V4186 Timing Pin (3) engages in slot (9).

47 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Push Rack To Shutoff

(11) 6V7942 Hook.

(12) Servo valve.

8. Move the governor control lever to the "FULL LOAD" position (rotate governor shaft clockwise)
and fasten it in this position.

Pull Rack Against Timing Pin

(11) 6V7942 Hook.

(12) Servo valve.

9. Use the 6V7942 Hook (11) to pull the sleeve and rack [through servo valve (12)] against the
timing pin.

Fuel Rack Against Timing Pin

10. Adjust the 6V6106 Dial Indicator (8) in the collet to zero and tighten the collet. Make sure all
needles of the indicator are on zero.

NOTE: If the Electronic Position Indicator Group is used, press the ZERO switch on the front panel.
This sets the display to zero.

11. Remove the 6V4186 Timing Pin (3), 6V7942 Hook (11) and release the governor control lever.

48 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

6V7941 Compressor Assembly

(13) Rod.

12. Turn rod (13) in the 6V7941 Compressor Assembly until the knob is approximately 25.4 mm
(1.00 in) away from the compressor body.

NOTE: The 6V7941 Compressor Assembly is used to compress the overfueling spring through the
linkage. The overfueling spring must be compressed to get an accurate fuel setting measurement.

Install The 6V7941 Compressor Assembly

(10) 6V6151 Adapter.

(14) 6V7941 Compressor Assembly.

13. Install 6V7941 Compressor Assembly (14) in 6V6151 Adapter (10) as shown.

Static Fuel Setting

(13) Rod (part of 6V7941 Compressor Assembly).

(15) 8T0500 Circuit Tester.

(16) Insulated terminal.

14. Fasten the clip end of the 8T0500 Circuit Tester (15) to insulated terminal (16), and put the other
end to a good electrical ground.

49 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

NOTE: If the Electronic Position Indicator Group is used, the built-in continuity tester can be used
instead of 8T0500 Circuit Tester (15). Use the built-in tester only for static readings.

15. Hold the governor control lever in the "FULL LOAD" position (rotate governor shaft clockwise).

16. Turn rod (13) of compressor assembly in (clockwise) until the light in 8T0500 Circuit Tester (15)
goes off and the dial indicator hands move an additional 2 mm in the negative (-) direction after the
light goes out (2 complete revolutions of the large needle on the dial indicator).

NOTICE

DO NOT turn the rod any further in if the rod begins to tighten.
Damage to the governor can occur if the rod is turned in further.

NOTE: The static fuel setting (Step 18) and the static full torque setting (Step 19) must be within ±
.25 mm of the setting on the Engine Information Plate. If the setting is within ± .25 mm an
adjustment is not necessary. If the Engine Information Plate is gone or the Full Torque Setting is not
on the Engine Information Plate, see TMI (Technical Marketing Information) or Fuel Setting And
Related Information Fiche for the correct settings.

Adjustment Of Governor
(17) Adjustment screw cover.

17. Remove adjustment screw cover (17) from the rear of the governor housing.

18. Slowly turn rod (13) out (counterclockwise) until the circuit tester light just comes on. This is the
static fuel setting. See the Engine Information Plate or the TMI (Technical Marketing Information) or
Fuel Setting And Related Information Fiche for the correct static fuel setting.

NOTE: When the rod is turned out, there can be a small initial movement of the dial indicator
hands, then, they will stop moving while the rod is turned out for approximately another 11/2 turns.
Now the indicator hands will begin to move again and will follow the turning of the rod until the
setting is reached. It is important that the rod be turned slowly so that the rack can follow the
governor components.

50 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

NOTE: If rod (13) is turned out too fast, a wrong measurement can be read on the dial indicator as
the light comes on. Repeat Steps 16 and 18 to make sure the correct measurement is taken.

19. Continue to turn the rod out until the indicator hand stops moving. Then turn the rod out two
additional turns. Push in on the rack stop collar to make sure it is in the correct position. The new
reading on the indicator is the full torque static setting.

Example:

Static Fuel Setting = 2.18 mm

Full Torque = 3.18 mm

This means the torque rise setting is 1.00 mm. An addition of the fuel setting and the torque rise
setting is not necessary.

20. See the Engine Information Plate or the TMI (Technical Marketing Information) for the correct
static full torque setting.

21. Determine how much the settings will have to be changed (see examples). Use the chart that
follows to determine how far the adjusting screws must be turned.

51 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Since "desired setting" is higher than "actual reading," turn adjusting screw out (counterclockwise)
approximately 1/4 turn. Recheck the new setting and readjust if necessary.

Since "desired setting" is lower than "actual reading," turn the adjusting screw in (clockwise)
approximately 1 1/8 turns. Recheck the new setting and readjust if necessary.

Negative numbers work differently than positive numbers. If one number (-1.25) has a large digital
value than another one (-1.05), the first number (-1.25) is actually less than the other one.
Therefore, in this example the "desired setting" is lower than the "actual reading". Turn the
adjusting screw in (clockwise) approximately 1/4 turn. Recheck the new setting and readjust if
necessary.

The "desired setting" is higher than the "actual reading". Turn the adjusting screw out
(counterclockwise) approximately 11/8 turns. Recheck the new setting and readjust if necessary.

52 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

The "desired setting" is lower than the "actual reading". Turn the adjusting screw in approximately
2 7/8 turns.

The "desired setting" is higher than the "actual reading". Turn the adjusting screw out
approximately 2 7/8 turns.

Adjustment Of Fuel Setting

(18) Fuel setting screw.

(19) 6V2106 Rack Adjustment Tool Group.

Adjustment Of Full Torque Setting

(19) 6V2106 Rack Adjustment Tool Group.

(20) Torque rise setting screw.

NOTE: If you are working from the side of the engine and cannot see the adjusting screws, use the
outer edge of the opening in the governor housing to guide the 6V2106 Tool Group onto the fuel
setting screw. Use the inner edge of the opening to guide the 6V2106 Tool Group onto the full

53 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

torque setting adjustment screw.

22. If both settings are to be increased, turn torque rise adjustment screw (20) out
(counterclockwise) the same number of turns as fuel setting adjustment screw (18) is going to be
changed. If the static fuel setting is going to be decreased, it is not necessary to change the full
torque setting at this time.

23. Use 6V2106 Rack Adjustment Tool Group (19) to loosen the locknuts for adjustment screws and
to turn the adjustment screws.

24. Adjust the fuel setting screw the number of turns determined in Step 21. Always recheck the
setting after each adjustment and adjust again if needed.

NOTE: There is a zero tolerance for the fuel setting and full torque setting when an adjustment is
made.

25. After the static fuel setting is correct, adjust the torque rise adjustment screw the number of
turns determined in Step 21. Always recheck the setting after each adjustment and adjust again if
needed.

Fuel Ratio Control And Governor Check

NOTE: The governor seals do not have to be cut or removed for the procedure that follows.

1. Install the rack position indicator to measure fuel rack movement. See Steps 1 and 2 in the Fuel
Setting Procedure for the correct installation of the tooling.

2. Turn the engine start key to the ON position to activate the shutoff solenoid. Do not start the
engine at this time.

3. Move the governor control linkage to the full FUEL ON position and hold or fasten it in this
position.

4. Install the 6V4186 Timing Pin in the rack zeroing hole near the front of the fuel injection pump
housing.

5. With the governor control lever in the full FUEL ON position, use a 1N9954 Lever and move the

54 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

manual shutoff shaft slowly to the FUEL OFF position (counterclockwise). Watch and make sure the
timing pin drops and engages with the slot in the fuel rack.

6. Release the manual shutoff shaft and zero the dial indicator. Move the dial indicator in the collet
to zero and tighten the collet. Make sure all three needles of the indicator are on zero.

7. Remove the 6V4186 Timing Pin and watch the dial indicator movement. The indicator should
show movement in the FUEL ON direction. If no movement occurs repeat Steps 4, 5 and 6 to zero
the indicator.

8. Release the governor control shaft and linkage.

Remove Boost Line

(1) Air Line.

9. Remove air line (1) from the engine. Put plugs over the openings to keep dirt out of the system.

To help prevent an accident caused by parts in rotation, work

carefully around an engine that has been started.

10. Start the engine and operate it for a minimum of five minutes to get the governor and engine up
to normal operating temperatures.

11. Check the leak down rate of the fuel ratio control (with the engine operating at low idle) as
follows:

a. Connect a pressure indicator, a shutoff valve, a pressure regulator and an air supply to fitting.

b. Apply 70 kPa (10 psi) air pressure to the fuel ratio control.

c. Turn the shutoff valve OFF and check the leak down rate. Leakage of 20 kPa (3 psi) in 30
seconds is acceptable.

d. If leakage is more than 20 kPa (3 psi) in 30 seconds, the fuel ratio control must be repaired
before Steps 13 and 14 are done.

55 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

e. Keep 70 kPa (10 psi) air pressure on the fuel ratio control for Step 12.

NOTE: Step 11 also activates the fuel ratio control for Step 12.

Apply Air Pressure

(2) Fitting.

(3) Cover.

12. From low idle, rapidly move the governor control shaft to the full FUEL ON position and read the
measurement on the dial indicator. Read the indicator carefully because this reading will be a
maximum for only a moment. Make a record of the maximum dial indicator reading. If full
measurement is not reached, increase the air pressure to make sure there is full fuel ratio control
movement.

NOTE: The fuel ratio control is activated and the maximum dial indicator reading is dynamic full
torque setting of the engine. This setting is 0.5 mm (.02 in) greater than the static full torque setting
given on the Engine Information Plate or later engines or in the TMI (Technical Marketing
Information) or Fuel Setting And Related Information Fiche.

NOTE: On some CARB approved engines or with fuel ratio controls out of adjustment, the fuel ratio
control can activate shortly after engine startup. At this time the dial indicator reading can be the
dynamic fuel ratio control setting. Continue the checking procedure to find the dynamic full torque
setting at Step 16.

13. Release all air pressure from the fuel ratio control. Start at 900 rpm and rapidly move the
governor control shaft to the full FUEL ON position and read the measurement on the dial indicator.
Read the dial indicator carefully because this reading will be a maximum for only a moment. Make a
record of the maximum dial indicator reading. This is the dynamic fuel ratio control setting for the
engine.

14. If the dynamic fuel ratio control setting is within ± 0.25 mm of the specification given on the
Engine Information Plate or in the TMI (Technical Marketing Information) or Fuel Setting And
Related Information Fiche, an adjustment is not necessary.

15. For adjustment of the control see Fuel Ratio Control Adjustment.

56 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

16. Check boost pressure that gives full torque rack travel as follows:

a. Connect a pressure indicator, a pressure regulator and an air supply to fitting (2).

b. Apply 25 kPa (4 psi) air pressure to the fuel ratio control.

c. Start at 900 rpm and rapidly move the governor control shaft to the full FUEL ON position and
make a record of the maximum dial indicator reading.

d. Repeat this procedure several times, each time increase the air pressure 5 kPa (.5 psi).

e. Make a record of the first air pressure setting that gives full torque rack travel. Full torque rack
travel was measured in Step 12.

f. This is the boost pressure that moves the fuel ratio control out of the rack control position. This
pressure gives dynamic full torque rack travel.

Fuel Ratio Control Adjustment

NOTE: These emissions certified engines have tamper resistant bolts on the fuel ratio control and
cover. Adjustments and repairs should be made by an authorized Caterpillar dealer. Refer to the
Disassembly & Assembly for the proper procedure of removing and installing the tamper resistant
bolts.

NOTE: Before the governor seals are cut or removed, See Fuel Ratio Control And Governor Check
to make sure an adjustment is needed.

To help prevent an accident caused by parts in rotation, work

carefully around an engine that has been started.

1. See the Engine Information Plate or the TMI (Technical Marketing Information) or Fuel Setting
And Related Information Fiche for correct dynamic fuel ratio control setting specification before an
adjustment is made.

2. Install and zero the rack position indicator group. See Fuel Ratio Control And Governor Check for
this procedure.

57 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Remove Boost Line

(1) Air line.

Remove Cover
(2) Fitting.

(3) Cover.

3. Remove air line (1) and cover (3) from the engine.

4. Start the engine and operate it for a minimum of five minutes to get the governor and engine up
to normal operating temperature.

Adjustment Components.
(4) Valve extension.

(5) Nut.

58 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

(6) Retainer.

5. Hold retainer (6) in position and loosen nut (5). This keeps the fuel ratio control diaphragm from
turning when nut (5) is loosened or tightened.

6. Turn valve extension (4) to get the correct setting. A clockwise direction gives a more positive
setting. The counterclockwise direction will give a more negative setting. Several adjustments of
valve extension (4) may be needed to get the correct dynamic fuel ratio control setting.

7. After each adjustment is made, check the dynamic fuel ratio control setting. Start at 900 rpm and
rapidly move the governor control shaft to the full Fuel On position and read the measurement on
the dial indicator. Read the dial indicator carefully because this reading will be a maximum for only a
moment. Make a record of the maximum dial indicator reading.

NOTE: If the correct dynamic fuel ratio control setting cannot be made with this adjustment, the
internal governor linkage must be checked and adjusted or the fuel ratio control needs repair or
replacement. See Check And Adjustment Of The Fuel Ratio Control Linkage for the governor
linkage procedure.

8. After the correct adjustment has been made, tighten nut (5). Check the dynamic fuel ratio control
setting again.

9. Install the gasket and cover (3) on the fuel ratio control. Tighten the bolts to a torque of 9 ± 3 N·m
(7 ± 2 lb ft).

10. Apply 70 kPa (10 psi) air pressure to the fuel ratio control at fitting (2). This will fully extend the
fuel ratio control to get dynamic full torque.

11. Check the dynamic full torque setting. Start at 900 rpm and rapidly move the governor control
shaft to the full Fuel On position and read the maximum measurement on the dial indicator.

NOTE: If the dynamic full torque setting cannot be reached a repair or replacement of the fuel ratio
control is needed.

12. Stop the engine.

13. Install the wire and seal on the fuel ratio control.

14. Install air line (1) on the engine.

15. Remove the rack position indicator tooling.

Check And Adjustment Of The Fuel Ratio Control

Linkage
59 of 119 1/24/2024, 3:43 PM
SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

6V6070 Governor Adjusting Tool Group

The check and adjustment of the fuel ratio control linkage can be used with the fuel injection pump
and governor on or off the engine.

NOTE: Start with Step 13 of this procedure if the governor adjusting tools have already been
installed to check the fuel setting.

Fuel Injection Pump And Governor

(1) Cover (rack position indicator).

(2) Plug (rack centering pin).

1. Remove plug (2) and cover (1) from the fuel injection pump housing.

Indicator And Centering Pin Installed

(3) 6V4186 Timing Pin.

(4) 8T9198 Bracket Assembly.

60 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

(5) 2A0762 Bolt.

(6) 8H9178 Ground Body Bolt.

(7) 5P4814 Collet.

(8) 6V6106 Dial Indicator.

2. Install the rack position indicator as follows:

a. Install the 5P4814 Collet (7) on the 8T9198 Bracket Assembly (4).

Slot In Fuel Injection Pump Rack

(9) Slot.

b. Position the indicator arm in approximately the middle of its travel to make sure that it will engage
in slot (9) in the rack. Put 8T9198 Bracket Assembly (4) in position on the fuel injection pump
housing.

c. Install 8H9178 Ground Body Bolt (6) first. Then install 2A0762 Bolt (5).

d. Be sure the indicator arm moves freely.

e. Put 6V6106 Dial Indicator (8) in position in 5P4814 Collet (7).

f. Put the 9S8903 Contact Point on the 6V2030 Extension and install on 6V6106 Dial Indicator (8).
NOTE: The 9S8903 Contact Point will not go through the collet and must be assembled after the
indicator stem has passed through the collet.

g. Tighten 5P4814 Collet (7) just enough to hold the dial indicator.

Position Fuel Injection Pump Rack

(10) 6V6151 Adapter.

(11) 6V7942 Hook.

61 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

3. Remove the shutoff solenoid, if equipped, or cover and install the 6V6151 Adapter (10).

4. Move the governor control lever to the Low Idle position (rotate governor shaft counterclockwise).

5. Install the 6V4186 Timing Pin (3) in the top of the fuel injection pump housing. Push the timing
pin in until contact with the fuel rack is made.

6. Use 6V7942 Hook (11) through 6V6151 Adapter (10) to push the sleeve and rack to the shutoff
position. Make sure 6V4186 Timing Pin (3) engages in slot (9).

Push Rack To Shutoff

(11) 6V7942 Hook.

(12) Servo valve.

7. Move the governor control lever to the Full Load position (rotate governor shaft clockwise) and
fasten it in this position.

Pull Rack Against Timing Pin

(11) 6V7942 Hook.

(12) Servo valve.

8. Use the 6V7942 Hook (11) to pull the sleeve and rack [through servo valve (12)] against the
timing pin.

62 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Fuel Rack Against Timing Pin

9. Adjust the 6V6106 Dial Indicator (8) in the collet to zero and tighten the collet. Make sure all three
needles of the dial indicator are on zero.

10. Remove the 6V4186 Timing Pin (3), 6V7942 Hook (11) and release the governor lever.

6V7941 Compressor Assembly

(13) Rod.

11. Turn rod (13) in the 6V7941 Compressor Assembly until the knob is approximately 25.4 mm
(1.00 in) away from the compressor body.

NOTE: The 6V7941 Compressor Assembly is used to remove clearance in the governor linkage to
get accurate fuel setting measurements.

Install the 6V7941 Compressor Assembly

(10) 6V6151 Adapter.

(14) 6V7941 Compressor Assembly.

12. Install 6V7941 Compressor Assembly (14) in 6V6151 Adapter (10) as shown.

Remove Fuel Ratio Control

63 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

(15) Air supply line.

(16) Fuel ratio control.

13. Remove air supply line (15) and fuel ratio control (16).

Remove Orifice Screen Assembly

(A) Location (for screen assembly).

Fuel Ratio Governor Adjustment Check

(17) 6V2017 Governor Adjusting Tool.

(18) 6V2106 Rack Adjusting Tool (outer part).

14. Remove the orifice screen assembly from the governor housing at location (A). This screen
must be removed to 6V2017 Governor Adjusting Tool (17) can fit square against the governor
housing.

NOTE: If it is thought that it will be necessary to change linkage adjustment, install the outer part of
6V2106 Rack Adjusting Tool (18) along the left side of the governor, before bolts for tool (17) are
tightened.

15. Move the governor control lever to the Low Idle position and install 6V2017 Governor Adjusting
Tool (17) as shown.

16. Move the governor control lever to Full Load position and hold there.

64 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Checking Fuel Ratio Control Setting

(14) 6V7941 Compressor Assembly.

17. Turn the knob so the rod moves in 6V7941 Compressor Assembly (14) until the needles of the
dial indicator move approximately 1 mm (one revolution of the large needle).

18. Slowly turn the knob to move the rod out of 6V7941 Compressor Assembly (14) until the
needles of the dial indicator stop movement. This is the Static Fuel Ratio Control Lever Setting.

NOTE: When the rod is turned out, there may be a small initial movement of the dial indicator
needles, then they will stop moving while the rod is turned out for approximately 1 1/2 turns more.
Now the indicator needles will begin to move again, and will follow the turning of the knob until the
setting is reached. It is important that the rod be turned slowly, so that fuel rack can follow the
movement of the governor components.

19. See the TMI (Technical Marketing Information) or Fuel Setting And Related Information Fiche
for the correct Static Fuel Ratio Control (lever) setting dimension, and compare it to the dial
indicator reading. The dial indicator reading must be within ± .25 mm (.010 in) of the dimension
given in the TMI (Technical Marketing Information) or Fuel Setting And Related Information Fiche or
an adjustment is needed.

Tools For Linkage Adjustment

(18) 6V2106 Rack Adjusting Tool (outer part).

(19) 6V2104 Hex Wrench.

65 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Location Of Linkage Adjustment

(20) Adjustment screw.

(21) Locknut.

20. If an adjustment is necessary, use 6V2106 Rack Adjusting Tool (18) to loosen the locknut (21)
and then use the 6V2104 Hex Wrench (19) (part of the 6V2106 Rack Adjusting Tool) to turn the
adjusting screw (20). Turn the screw out [counterclockwise (CCW)] to make the setting more
positive, or in [clockwise (CW)] to make the setting more negative. Be sure to tighten the locknut
after adjustment is complete. There is a zero tolerance for the linkage setting if an adjustment is
made.

NOTE: The needles of the dial indicator will not follow the turning of the adjustment screw. It will be
necessary to do Steps 15 through 17 until the adjustment is correct.

Adjustment Of Fuel Ratio Control Linkage

Engine Speed Measurement

66 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

9U7400 Multitach Group

The 9U7400 Multitach Group can measure engine speed from a magnetic pickup on the flywheel
housing. It also has the ability to measure engine speed from visual engine parts in rotation.

Operators Manual NEHS0605 is with the 9U7400 Multitach Group and gives instructions for the test
procedure.

The 6V4950 Injection Line Speed Pickup Group is another diagnostic tool accessory that can be
used with the 6V2100 Multitach. It can be used on all Caterpillar Diesel Engines equipped with 6
mm (.25 in) single wall fuel injection lines. With this pickup group, engine speed can be measured
quickly, automatically and with an accuracy of ± 1 rpm.

Special Instruction, SEHS8029 is with the group and gives instructions for use of the 6V4950
Injection Line Speed Pickup Group.

Governor Adjustments

NOTICE

A mechanic with training in governor adjustments is the only

one to make the adjustment to the set point rpm.

67 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Engine rpm must be checked with an accurate tachometer. Make reference to Engine Speed
Measurement.

Low Idle Adjustment

NOTE: The correct Low Idle rpm is given in the TMI (Technical Marketing Information) or Fuel
Setting And Related Information Fiche.

To help prevent an accident caused by parts in rotation, work

carefully around an engine that has been started.

Start the engine and run until the temperature of normal operation is reached. Check low idle rpm
with no load on the engine. If an adjustment is necessary, use the procedure that follows:

Low Idle Adjustment

(1) Low idle stop screw.

1. To adjust the Low Idle rpm, start the engine and run with the governor control lever in the low idle
position. Loosen the locknut for low idle screw (1). Turn the low idle screw to get the correct low idle
rpm. Increase engine speed and return to low idle and check low idle speed again. Tighten the
locknut.

Checking Set Point (Balance Point)

The engine set point is an adjusted specification and is important to the correct operation of the
engine. High idle rpm is NOT an adjusted specification. Set point (formerly balance point) is full load
rpm plus an additional 20 rpm. Set point is the rpm at which the fuel setting adjustment screw and
stop or first torque spring just start to make contact. At this rpm, the fuel setting adjustment screw
and stop or first torque spring still have movement between them. When additional load is put on
the engine, the fuel setting adjustment screw and stop or first torque spring will become stable
against each other. Set point is controlled by the fuel setting and the high idle adjustment screw.

68 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

There is a new and more accurate method for checking the "set point", formerly called the balance
point, of the engine. If the tools for the new method are not available, there is an alternate method
for checking the "set point".

The 9U7400 Multitach Group can be used to check the set point. Operators Manual NEHS0605
gives instructions for installation and use of this tool group.

9U7400 Multitach Group

Alternate Method

NOTE: Do not use the machine tachometer unless its accuracy is know to be within ± 1 rpm.

If the set point is correct and the high idle speed is within specifications, the fuel system operation
of the engine is correct. The set point for the engine is:

A. At 20 rpm greater than full load speed.

B. The rpm where the fuel setting adjustment screw stop or first torque spring just make contact.

69 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Use the procedure that follows to check the set point. Make reference to Techniques For Loading
Engines in Special Instruction SEHS7050.

1. Connect a tachometer which has good accuracy to the tachometer drive.

Terminal Location
(2) Brass terminal screw.

2. Connect the clip end of the 8T0500 Circuit Tester to the brass terminal screw (2) on the governor
housing. Connect the other end of the tester to a place on the fuel system which is a good ground
connection.

Work carefully around an engine that is running. Engine parts

that are hot, or parts that are moving, can cause personal injury.

3. Start the engine.

4. With the engine at normal conditions for operation, run the engine at high idle.

5. Make a record of the speed of the engine at high idle.

6. Add load on the engine slowly until the circuit tester light just comes on (minimum light output).
This is the set point.

7. Make a record of the speed (rpm) at the set point.

8. Repeat Step 6 several times to make sure that the reading is correct.

9. Stop the engine. Make a comparison of the records from Steps 6 and 7 with Full Load Speed
from the Engine Information Plate. If the Engine Information Plate is not available, see the TMI
(Technical Marketing Information) or Fuel Setting And Related Information Fiche. The tolerance for
the set point is ± 10 rpm. The tolerance for the high idle rpm is ± 50 rpm in chassis and ± 30 rpm on
a bare engine. If the readings from Steps 5 and 7 are within the tolerance, no adjustment is needed.

70 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

NOTE: Engines will have the actual Dyno High Idle stamped on the Engine Information Plate. It is
possible, in some applications that the high idle rpm will be less than the actual lower limit. This can
be caused by high parasitic loads such as hydraulic pumps, compressors, etc.

Adjusting Set Point (Balance Point)

1. If the set point and the high idle rpm are within tolerance, no adjustment is to be made.

Remove Cover
(3) Cover.

2. If the set point rpm is not correct, remove cover (3).

Set Point Adjustment

(4) Locknut.

(5) Adjustment screw.

3. Loosen locknut (4) and turn adjustment screw (5) to adjust the set point to the midpoint of the
tolerance.

4. When the set point is correct, check the high idle rpm. The high idle rpm must not be more than
the high limit of the tolerance.

If the high idle rpm is more than the high limit of the tolerance, check the governor spring and
flyweights. If the high idle rpm is less than the low limit of the tolerance, check for excess parasitic
loads and then the governor spring and flyweights.

Dashpot Adjustment

71 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Adjustment Of Dashpot
(1) Needle Valve.

This adjustment controls the amount of restriction to oil flow into and out of the dashpot chamber.
Too much oil flow will cause the governor to hunt, and too little oil flow will cause a slow governor
action.

1. Turn needle valve (1) in (clockwise) until it stops. Now, open needle valve (1) two full turns
(counterclockwise). The exact point of adjustment is where the governor gives the best
performance.

NOTE: Do not keep needle valve (1) fully closed. This can cause excessive overshoot on start up
or load rejection.

2. Check governor operation.

With the engine running at medium (mid) speed, load the engine (at least one-quarter load) to find
the stability of the setting. Quickly remove the load. A slight overshoot of speed is desired, as it
reduces response time. The engine speed should return to smooth steady operation. If it does not
have a slight overshoot and return to a smooth steady operation, adjust the needle valve and repeat
the above procedure.

Air Inlet And Exhaust System

Restriction Of Air Inlet And Exhaust
There will be a reduction of horsepower and efficiency of the engine if there is a restriction in the air
inlet or exhaust system.

Air flow through the air cleaner must not have a restriction (negative pressure difference
measurement between atmospheric air and air that has gone through air cleaner) of more than 6.22
kPa (25 inches of H2O).

Back pressure from the exhaust (pressure difference measurement between exhaust at outlet
elbow and atmospheric air) must not be more than 10 kPa (40 inches of H2O).

72 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Measurement Of Pressure In Inlet Manifold

The efficiency of an engine can be checked by making a comparison of the pressure in the inlet
manifold with the information given in the TMI (Technical Marketing Information) or Fuel Setting And
Related Information Fiche. This test is used when there is a decrease of horsepower from the
engine, yet there is no real sign of a problem with the engine.

The correct pressure for the inlet manifold is given in the TMI (Technical Marketing Information) or
Fuel Setting And Related Information Fiche. Development of this information is done with these
conditions:

a. 100 kPa (29 inches of Hg) (DRY) barometric pressure.

b. 29°C (85°F) outside air temperature.

c. 35 API rated fuel.

On a turbocharged and aftercooled engine, a change in fuel rating will also change horsepower and
the pressure in the inlet manifold. If the fuel is rated above 35 API, pressure in the inlet manifold
can be less than given in the TMI (Technical Marketing Information) or Fuel Setting And Related
Information Fiche. If the fuel is rated below 35 API, the pressure in the inlet manifold can be more
than given in the TMI (Technical Marketing Information) or Fuel Setting And Related Information
Fiche. Be sure that the air inlet or exhaust does not have a restriction when making a check
of pressure in the inlet manifold.

Inlet Manifold Plug For Pressure Test

Use the 1U5470 Engine Pressure Group to check the pressure in the inlet manifold.

73 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

1U5470 Engine Pressure Group

This tool group has a indicator to read pressure in the inlet manifold. Special Instruction SEHS8907
is with the tool group and gives instructions for its use.

Turbocharger
If any unusual sound or vibration in the turbocharger is noticed, a quick check of bearing condition
can be made without disassembling the turbocharger. This can be done by removing the piping
from the turbocharger and inspecting the compressor impeller, turbine wheel and compressor cover.
Rotate the compressor and turbine wheel assembly by hand and observe by feeling excess end
play. The rotating assembly should rotate freely with no rubbing or binding. If there is any indication
of the impeller rubbing the compressor cover or the turbine wheel rubbing the turbine housing,
recondition the turbocharger or replace with a new or rebuilt one.

End play is best checked with a dial indicator. Attach a dial indicator with the indicator point on the
end of the shaft. Move the shaft from end to end making note of the total indicator reading.

End play for the turbocharger should be 0.114 ± 0.038 mm (.0045 ± .0015 in). Maximum
permissible end play for the S4DS Turbocharger is 0.20 mm (.008 in). If end play is more than the
maximum end play, rebuild or replace the turbocharger. End play less than the minimum end play
could indicate carbon build up on the turbine wheel and the turbocharger should be disassembled
for cleaning and inspection.

74 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Checking Turbocharger Rotating Assembly End play (Typical Example)

A more reliable check of bearing conditions can be made only when the turbocharger is
disassembled and the bearings, shaft journal and housing bore diameters can actually be
measured.

Exhaust Temperature

Use the 123-6700 Infrared Thermometer to check exhaust temperature. The Operator's Manual
NEHS0630, for the 123-6700 Infrared Thermometer gives complete operating and maintenance
instructions for this tool.

Crankcase (Crankshaft Compartment) Pressure

Pistons or rings that have damage can be the cause of too much pressure in the crankcase. This
condition may cause the engine to run rough. There will also be more than the normal amount of
fumes (blowby) coming from the crankcase breather. The breather can then become restricted in a
very short time, causing oil leakage at gaskets and seals that would not normally have leakage.
Other sources of blowby can be worn valve guides or turbocharger seal leakage.

75 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

8T2700 Indicator Group

The 8T2700 Indicator Group is used to check the amount of blowby. The test procedure is in
Special Instruction SEHS8712.

Compression
An engine that runs rough can have a leak at the valves, or have valves that need adjustment.
Removal of the head and inspection of the valves and valve seats is necessary to find those small
defects that do not normally cause a problem. Repair of these problems is normally done when
reconditioning the engine.

Cylinder Head
The cylinder head has valve seat inserts, valve guides and bridge dowels that can be removed
when they are worn or have damage. Replacement of these components can be made with the
tools that follow.

Valves
Valve removal and installation is easier with use of the 5S1330 Valve Spring Compressor Assembly
and 5S1322 Valve Keeper Inserter.

Valve Seat Inserts

Tools needed to remove and install valve seat inserts are in the 6V4805 Valve Insert Puller Group.
Special Instruction SMHS7935 gives an explanation for the procedure to remove the valve seat
inserts. For easier installation, lower the temperature of the insert before it is installed in the head.

Valve Guides

76 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Tools needed to remove and install valve guides are the 5P2396 Driver Bushing and 7S8859 Driver.
The counterbore in the driver bushing installs the guide to the correct height. Use a 1P7451 Valve
Guide Honing Group to make a finished bore in the valve guide after installation of the guide in the
head. Special Instruction SMHS7526 gives an explanation for this procedure. Grind the valves after
the new valve guides are installed.

Checking Valve Guide Bores

Use the 5P3536 Valve Guide Gauge Group to check the bore of the valve guides. Special
Instruction GMG02562 gives complete and detailed instructions for use of the 5P3536 Valve Guide
Gauge Group.

Bridge Dowel
Use a 5P0944 Dowel Puller Group with a 5P0942 Extractor to remove the bridge dowels. Install a
new bridge dowel with a 5P2406 Dowel Driver. This dowel driver installs the bridge dowel to the
correct height.

Bridge Adjustment
When the head is disassembled, keep the bridges with their respective cylinders. Adjustment of the
bridge will be necessary after the valves are ground or other reconditioning of the cylinder head is
done. The bridge should be checked and/or adjusted each time the valves are adjusted. To check
for wear use a dial indicator to measure the amount of wear on the bridge seat. Make sure the
contact point on the dial indicator is small enough in diameter to get an accurate measurement.

Dimensions For Reconditioning Bridge Seat

(A) Minimum dimension after reconditioning - 16.51 mm (.650 in).

77 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

(B) Allowable wear before reconditioning - 0.13 mm (.005 in).

Use the bridge again if the wear is 0.13 mm (.005 in) or less. When the wear seat is worn more than
the allowable limit, the worn surface of the seat can be ground flat. The maximum amount of
material that can be removed is 0.38 mm (.015 in). If the seat cannot be made flat, replace the
bridge. Reconditioning of the wear seat can only be done once.

Use the procedure that follows to make an adjustment to the bridge.

NOTE: Valves must be fully closed.

Bridge Adjustment
1. Put engine oil on the bridge dowel in the cylinder head and in the bore in the bridge.

2. Install the bridge with the adjustment screw toward the exhaust manifold.

3. Loosen the locknut for the adjustment screw and loosen the adjustment screw several turns.

4. Put a force on the bridge with a finger to keep the bridge in contact with the valve stem opposite
the adjustment screw.

5. Turn the adjustment screw clockwise until it just makes contact with the valve stem. Then turn the
adjustment screw 30 degrees more in a clockwise direction to make the bridge straight on the
dowel, and to make compensation for the clearance in the threads of the adjustment screw.

6. Hold the adjustment screw in this position and tighten the locknut to 30 ± 4 N·m (22 ± 3 lb ft).

7. Put engine oil at the point where the rocker arm makes contact with the bridge.

Valve Lash Setting

NOTE: Valve lash is measured between the rocker arm and the bridge for the valves.

78 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

NOTE: When the valve lash is checked, adjustment is not necessary if the measurement is in the
range given in the chart for Valve Lash Check: Engine Stopped. If the measurement is outside this
range, adjustment is necessary. See the chart for Valve Lash Setting: Engine Stopped, and make
the setting to the nominal (desired) specifications in this chart.

Valve Lash Check

To make an adjustment to the valve lash, turn the adjustment screw in the rocker arm. Valve lash
adjustments can be made by using the procedure that follows:

1. Put No. 1 piston at top center (TC) on the compression stroke. Make reference to Finding Top
Center Compression Position For No. 1 Piston.

2. Make an adjustment to the valve lash on the inlet valves for cylinders 1, 2 and 4. make an
adjustment to the valve lash on the exhaust valves for cylinders 1, 3, and 5.

Valve Adjustment
3. After each adjustment, tighten the nut for valve adjustment screw to 30 ± 4 N·m (22 ± 3 lb ft), and
check the adjustment again.

4. Remove the timing bolt and turn the flywheel 360 degrees in the direction of engine rotation. This
will put No. 6 piston at top center (TC) on the compression stroke. Install the timing bolt in the
flywheel.

79 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

5. Make an adjustment to the valve lash on the inlet valves for cylinders 3, 5, and 6. Make an
adjustment to the valve lash on the exhaust valves for cylinders 2, 4, and 6.

6. Remove the timing bolt from the flywheel when all adjustments to the valve lash have been
made.

Cylinder And Valve Location

Jake Brake Adjustment

NOTE: Slave piston lash is measured between the slave piston (both ends of the yoke) and the
bridge.

NOTE: See the specifications on the brake serial number plate for the slave piston lash setting.

Use the procedure that follows to make the adjustment:

80 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Slave Piston Lash Adjustment (Typical Example)

(1) Screwdriver.

(2) Adjustment screw.

(3) Locknut.

(4) Feeler gauges.

1. Put No. 1 piston at top center (TC) on the compression stroke. Make reference to Finding Top
Center Compression Position For No. 1 Piston.

2. Loosen locknut (3). With screwdriver (1), turn adjustment screw (2) to make correct adjustment
for cylinders 1, 3, and 5.

3. After each adjustment, tighten locknut (3) to a torque of 22 N·m (16 lb ft) and check the slave
piston lash again.

NOTE: Be sure to check the lash with two feeler gauges (4) at the same time (one under each side
of slave piston).

4. Remove the timing bolt and turn the flywheel 360 degrees in the direction of engine rotation. This
will put No. 6 piston at top center (TC) on the compression stroke. Install the timing bolt in the
flywheel.

5. Make an adjustment to the slave piston lash for cylinders 2, 4, and 6.

6. Remove the timing bolt from the flywheel when all adjustments have been made.

Lubrication System
One of the problems in the list that follows will generally be an indication of a problem in the
lubrication system for the engine.

* Too Much Oil Consumption

* Oil Pressure Is Low

* Oil Pressure Is High

* Too Much Bearing Wear

* Increased Oil Temperature

Too Much Oil Consumption

Oil Leakage On Outside Of Engine
Check for leakage at the seals at each end of the crankshaft. Look for leakage at the oil pan gasket

81 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

and all lubrication system connections. Check to see if oil comes out of the crankcase breather.
This can be caused by combustion gas leakage around the pistons. A dirty crankcase breather will
cause high pressure in the crankcase, and this will cause gasket and seal leakage.

Oil Leakage Into Combustion Area Of Cylinders

Oil leakage into the combustion area of the cylinders can be the cause of blue smoke. There are
four possible ways for oil leakage into the combustion area of the cylinders:

1. Oil leakage between worn valve guides and valve stems.

2. Worn or damaged piston rings, or dirty oil return holes

3. Compression ring and/or intermediate ring not installed correctly.

4. Oil leakage past the seal rings in the impeller end of the turbocharger shaft.

Too much oil consumption can also be the result if oil with the wrong viscosity is used. Oil with a
thin viscosity can be caused by fuel leakage into the crankcase, or by increased engine
temperature.

Measuring Engine Oil Pressure

An oil pressure indicator that has a defect can give an indication of low oil pressure.

The 1U5470 Engine Pressure Group can be used to check engine oil pressure.

82 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

1U5470 Engine Pressure Group

This tool group has a indicator to read oil pressure in the engine. Special Instruction SEHS8907 is
with the tool group and gives instructions for the test procedure.

1. Be sure that the engine is filled to the correct level with SAE 10W30 oil. If any other viscosity of
oil is used, the information in the Engine Oil Pressure Graph does not apply.

Oil Manifold (Right Side Of Engine)

(1) Pressure test location.

Oil Pressure Indicator Connection (Left Side Of Engine)

(2) Pressure test location.

2. Connect the 1U5470 Engine Pressure Group to the main oil manifold at pressure test location (1)
or pressure test location (2).

3. Operate the engine to get it up to normal operating temperature.

4. Keep the oil temperature constant with the engine at its rated rpm, and read the pressure
indicator.

NOTE: Make sure engine oil temperature does not go above 115°C (239°F).

5. On the Engine Oil Pressure Graph, find the point that the lines for engine rpm and oil pressure
intersect (connect).

83 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Engine Oil Pressure Graph

6. If the results do not fall within the "ACCEPTABLE" pressure range given in the graph, find the
cause and correct it. Engine failure or a reduction in engine life can be the result if engine operation
is continued with oil manifold pressure outside this range.

NOTE: A record of engine oil pressure, kept at regular intervals, can be used as an indication of
possible engine problems or damage. If there is a sudden increase or decrease of 70 kPa (10 psi)
in oil pressure, even though the pressure is in the "ACCEPTABLE" range on the graph, the engine
should be inspected and the problem corrected.

Oil Pressure Is Low

Crankcase Oil Level

84 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Check the level of the oil in the crankcase. Add oil if needed. It is possible for the oil level to be too
far below the engine oil pump supply tube. This will cause the engine oil pump to not have the
ability to supply enough lubrication to the engine components.

Engine Oil Pump Does Not Work Correctly

The inlet screen of the supply tube for the engine oil pump can have a restriction. This will cause
cavitation (low pressure bubbles suddenly made in liquids by mechanical forces) and a loss of oil
pressure. Air leakage in the supply side of the engine oil pump will also cause cavitation and loss of
oil pressure. If the bypass valve for the engine oil pump is held in the open (unseated) position, the
lubrication system can not get to a maximum pressure. Engine oil pump gears that have too much
wear will cause a reduction in oil pressure.

Engine Oil Filter Bypass Valves

If the bypass valve for the engine oil filter is held in the open position (unseated) because the
engine oil filter has a restriction, a reduction in oil pressure can result. To correct this problem,
remove and clean the bypass valve and bypass valve bore. Install a new engine oil filter to be sure
that no more debris makes the bypass valve stay open.

Too Much Clearance At Engine Bearings Or Open Lubrication

System (Broken Or Disconnected Oil Line Or Passage)
Components that are worn and have too much bearing clearance can cause oil pressure to be low.
Low oil pressure can also be caused by an oil line or oil passage that is open, broken or
disconnected.

Piston Cooling Jets

When the engine is operated, piston cooling jets direct oil toward the bottom of the piston to lower
piston and ring temperatures. If there is a failure of one of the piston cooling jets, or it is bent in the
wrong direction, seizure of the piston will be caused in a very short time.

To eliminate the possibility of damaging piston cooling jets during removal of the connecting rod
cap, the piston cooling jets should always be removed. The wider connecting rod cap design,
cannot be removed without damaging the double piston cooling jet design.

Use the 5P8709 Piston Tool Group to check and adjust the alignment of piston cooling jets.

NOTE: This tool group does not currently accommodate the double piston cooling jet design.

Oil Pressure Is High

Oil pressure will be high if the bypass valve for the engine oil pump can not move from the closed

85 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

position.

Too Much Bearing Wear

When some components of the engine show bearing wear in a short time, the cause can be a
restriction in an oil passage.

If the indicator for oil pressure shows enough oil pressure, but a component is worn because it can
not get enough lubrication, look at the passage for oil supply to the component. A restriction in a
supply passage will not let enough lubrication get to a component, and this will cause early wear.

Increased Oil Temperature

Look for a restriction in the oil passages of the engine oil cooler. If the engine oil cooler has a
restriction, the oil temperature will be higher than normal when the engine is operated. The oil
pressure of the engine will not get low just because the engine oil cooler has a restriction.

Also check the engine oil cooler bypass valve to see if it is held in the open position (unseated).
This condition will let oil through the valve instead of the engine oil cooler, and oil temperature will
increase.

Cooling System
This engine has a pressure type cooling system. A pressure type cooling system gives two
advantages. The first advantage is that the cooling system can have safe operation at a
temperature that is higher than the normal boiling (steam) point of water. The second advantage is
that this type system prevents cavitation (low pressure bubbles suddenly made in liquids by
mechanical forces) in the water pump. With this type system, it is more difficult for an air or steam
pocket to be made in the cooling system.

The cause for increased engine temperature is generally because regular inspections of the cooling
system were not made. Make a visual inspection of the cooling system before a test is made with
test equipment.

Visual Inspection Of The Cooling System

1. Check coolant level in the cooling system.

2. Look for leaks in the system.

NOTE: Water pump seals. A small amount of coolant leakage across the surface of the "face-type"
seals is normal, and required, to provide lubrication for this type of seal. A hole is provided in the
water pump housing to allow this coolant/seal lubricant to drain from the pump housing. Intermittent

86 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

leakage of small amounts of coolant from this hole is not an indication of water pump seal failure.
Replace the water pump seals only if a large amount of leakage, or a constant flow of coolant is
observed draining from the water pump housing.

3. Look for bent radiator fins. Be sure that air flow through the radiator does not have a restriction.

4. Inspect the drive belts for the fan.

5. Check for damage to the fan blades.

6. Look for air or combustion gas in the cooling system.

7. Inspect the filler cap and the surface that seals the cap. This surface must be clean.

Testing The Cooling System

Remember that temperature and pressure work together. When a diagnosis is made of a cooling
system problem, temperature and pressure must both be checked. Cooling system pressure will
have an effect on cooling system temperatures. For an example, look at the chart to see the effect
of pressure and height above sea level on the boiling (steam) point of water.

Test Tools for Cooling System

87 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

4C6500 Digital Thermometer Group

The 4C6500 Digital Thermometer Group is used in the diagnosis of overheating (engine hotter than
normal) or overcooling (engine cooler than normal) problems. This group can be used to check
temperatures in several different parts of the cooling system. The testing procedure is in Operating
Manual NEHS0554.

8T2700 Blowby/Air Flow Indicator Group

The 8T2700 Blowby/Air Flow Indicator Group is used to check the air flow through the radiator core.
The test procedure is in Special Instruction SEHS8712.

88 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

9U7400 Multitach Group

The 9U7400 Multitach Group is used to check the fan speed. The testing procedure is in Operators
Manual NEHS0605.

9S8140 Cooling System Pressurizing Pump Group

The 9S8140 Cooling System Pressurizing Pump Group is used to test pressure caps and to
pressure check the cooling system for leaks.

DO NOT loosen the filler or pressure cap on a hot engine. Steam

or hot coolant can cause severe burns.

89 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Checking Pressure Cap

One cause for a pressure loss in the cooling system can be a defective seal on the radiator
pressure cap.

DO NOT loosen the filler or pressure cap on a hot engine. Steam

or hot coolant can cause severe burns.

After the engine is cool, loosen the pressure cap and let the pressure out of the cooling system.
Then remove the pressure cap.

Typical Schematic Of Pressure Cap

(A) Sealing surface of cap and radiator.

Inspect the pressure cap carefully. Look for damage to the seal or to the surface that seals. Any
foreign material or deposits on the cap, seal or surface that seals, must be removed.

The 9S8140 Cooling System Pressurizing Pump Group is used to test pressure caps and to

90 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

pressure check the cooling system for leaks.

DO NOT loosen the filler or pressure cap on a hot engine. Steam

or hot coolant can cause severe burns.

To check the pressure cap for the pressure that makes the pressure cap open, use the procedure
that follows:

1. Remove the pressure cap from the radiator.

2. Put the pressure cap on the 9S8140 Cooling System Pressurizing Pump Group.

3. Look at the indicator for the exact pressure that makes the pressure cap open.

4. Make a comparison of the reading on the indicator with the correct pressure at which the
pressure cap must open.

NOTE: The correct pressure that makes the pressure cap open is on the pressure cap and is also
in the Specifications module.

5. If the pressure cap is defective, install a new pressure cap.

Testing Radiator And Cooling System For Leaks

To test the radiator and cooling system for leaks, use the procedure that follows:

DO NOT loosen the filler or pressure cap on a hot engine. Steam

or hot coolant can cause severe burns.

1. Remove the pressure cap from the radiator.

2. Make sure the coolant is over the top of the radiator core.

91 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

3. Put the 9S8140 Cooling System Pressurizing Pump Group on the radiator.

4. Operate the pump group and get a pressure reading on the indicator that is 20 kPa (3 psi) more
than the pressure marked on the pressure cap.

5. Check the radiator for outside leakage.

6. Check all connections and hoses for the cooling system for outside leakage.

7. If you do not see any outside leakage and the pressure reading on the indicator is still the same
after five minutes, the radiator and cooling system does not have leakage. If the reading on the
indicator goes down and you do not see any outside leakage, there is leakage on the inside of the
cooling system. Make repairs as necessary.

Indicator For Water Temperature

4C6500 Digital Thermometer Group

If the engine gets too hot and a loss of coolant is a problem, a pressure loss in the cooling system
could be the cause. If the indicator for water temperature shows that the engine is getting too hot,
look for coolant leakage. If a place can not be found where there is coolant leakage check the
accuracy of the indicator for water temperature. A temperature indicator of known accuracy can be
used to make this check. Also, the 4C6500 Digital Thermometer Group may be used.

Work carefully around an engine that is running. Engine parts

that are hot, or parts that are moving, can cause personal injury.

92 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Water Temperature Indicator

Start the engine and run it until the temperature is at the desired range according to the test
indicator or thermometer. If necessary, put a cover over part of the radiator or cause a restriction of
the coolant flow. The reading on the indicator for water temperature must be the same as the test
indicator or thermometer within the tolerance range in the chart.

Water Temperature Regulators

1. Remove the regulator from the engine.

2. Heat water in a pan until the temperature is 98°C (208°F). Move the water around in the pan to
make it all the same temperature.

3. Hang the regulator in the pan of water. The regulator must be below the surface of the water and
it must be away from the sides and bottom of the pan.

4. Keep the water at the correct temperature for ten minutes.

93 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

5. After ten minutes, remove the regulator and immediately measure the distance the regulator has
opened. The distance must be a minimum of:

111-8010 Water Temperature Regulator ... 9.5 mm (.37 in)

4W4794 Water Temperature Regulator ... 10.4 mm (.41 in)

6. Make a replacement of the regulator if the distance is less than:

111-8010 Water Temperature Regulator ... 9.5 mm (.37 in)

4W4794 Water Temperature Regulator ... 10.4 mm (.41 in)

Belt Tightening Chart

Basic Block
Piston Rings
This engine has piston grooves and rings of the KEYSTONE (taper) design. The 1U6431 Gauge
Group is available to check the top two ring grooves in the piston. For correct use of the gauge
group see the instruction card that is with the gauge group.

94 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Instructions For 1U6431 Gauge Group

Connecting Rods And Pistons

Use the 7M3978 Piston Ring Expander to remove or install piston rings.

Use the 5P3526 Piston Ring Compressor to install pistons into cylinder block.

Tighten the connecting rod nuts in the step sequence that follows:

1. Put 2P2506 Thread Lubricant on bolt threads and contact surfaces of nut and cap.

2. Tighten all nuts to 80 ± 8 N·m (60 ± 6 lb ft).

3. Put a mark on each nut and end of bolt.

4. Tighten each nut 120 degrees from the mark.

The connecting rod bearings fit tightly in the bore in the rod. If bearing joints or backs are worn
(fretted), check bore size. This can be an indication of wear because of a loose fit.

Connecting Rod And Main Bearings

Connecting rod bearings are available with 0.63 mm (.025 in) and 1.27 mm (.050 in) smaller inside
diameter than the original size bearings. These bearings are for crankshafts that have been
"ground" (made smaller than the original size).

Main bearings are available with a larger outside diameter than the original size bearings. These
bearings are for cylinder blocks that have had the bore for the main bearings "bored" (made larger
than the original size). The size available is 0.63 mm (.025 in) larger outside diameter than the

95 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

original size bearings.

Cylinder Block

1P3537 Dial Bore Indicator Group

The bore in the block for main bearings can be checked with the main bearing caps installed
without bearings. Tighten the nuts that hold the caps to the torque shown in the Specifications
module. Alignment error in the bores must not be more than 0.08 mm (.003 in). Special Instruction
SMHS7606 gives instructions for the use of 1P4000 Line Boring Tool Group for alignment of the
main bearing bores. The 1P3537 Dial Bore Indicator Group can be used to check the size of the
bores. Special Instruction GMG00981 is with the group.

Cylinder Liner Projection

NOTE: This procedure alleviates the need for the "H" bar to hold down liners during projection
measurements.

96 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Liner Projection Components

(1) Bolt.

(2) Washer.

(3) Washer.

1. Install clean liners or cylinder packs (without the filler band or the rubber seals), spacer plate
gasket and clean spacer plate.

97 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

98 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

2. Install bolts and washers, as indicated previously, in the holes indicated with an X. Install all bolts
or the six bolts around the liner. Tighten the bolts to a torque of ... 95 N·m (70 lb ft).

3. Use the 8T0455 Liner Projection Tool Group to measure liner projection at positions indicated

99 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

with an A, B, C and D. Record measurements for each cylinder. Add the four readings for each
cylinder and divide by four to find the average.

4. If the liner projections are out of specification, try rotating the liner or install the liner in another
bore to see if the measurements improve.

5. If the liner projections are all below the specifications or low in the range, 0.025 mm (.0010 in) or
0.051 mm (.0020 in), try using a thinner spacer plate (6I3189 or 6I4303). These plates are 0.076
mm (.0030 in) thinner than the regular plate and they will increase the liner projection, thus
increasing the fire ring crush. Use these spacer plates to compensate for low liner projections that
are less than 0.076 mm (.0030 in) or if the inspection of the top deck reveals no measurable
damage directly under the liner flanges, but the average liner projection is less than 0.076 mm
(.0030 in).

NOTE: Do not exceed the maximum liner projection of 0.152 mm (.0060 in). Excessive liner
projection will contribute to liner flange cracking.

6. With the proper liner projection, mark the liners in the proper position and set them aside.

7. When the engine is ready for final assembly, the O-ring seals, cylinder block and upper filler band
must be lubricated before installation.

If the lower O-rings are black in color, apply liquid soap on the lower O-ring seals and the cylinder
block. Use clean engine oil on the upper filler band.

If the lower O-rings are brown in color, apply engine oil on the lower O-ring seals, the cylinder block
and the upper filler band.

NOTE: Apply liquid soap and/or clean engine oil immediately before assembly. If applied too early,
the seals may swell and be pinched under the liners during installation.

Flywheel And Flywheel Housing

100 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Heat the ring gear to install it. Do not heat to more than 315°C (600°F). Install the ring gear so the
chamfer on the gear teeth are next to the starter pinion when the flywheel is installed.

Face Run Out (Axial Eccentricity) Of The Flywheel Housing

If any method other than given here is used, always remember bearing clearance must be removed
to get correct measurements.

8T5096 Dial Indicator Group Installed

101 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Checking Face Runout Of The Flywheel Housing

(A) Bottom.

(B) Right side.

(C) Top.

(D) Left side.

1. Fasten a dial indicator to the crankshaft flange so the anvil of the indicator will touch the face of
the flywheel housing.

2. Put a force on the crankshaft toward the rear before the indicator is read at each point.

3. With dial indicator set at 0.0 mm (.00 in) at location (A), turn the crankshaft and read the indicator
at locations (B), (C) and (D).

4. The difference between lower and higher measurements taken at all four points must not be
more than 0.38 mm (.015 in), which is the maximum permissible face run out (axial eccentricity) of
the flywheel housing.

Bore Runout (Radial Eccentricity) Of The Flywheel Housing

102 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

8T5096 Dial Indicator Group Installed

1. Fasten the dial indicator as shown so the anvil of the indicator will touch the bore of the flywheel
housing.

2. With the dial indicator in position at (C), adjust the dial indicator to "0" (zero). Push the crankshaft
up against the top of the bearing. Write the measurement for bearing clearance on line 1 in column
(C) in the chart for dial indicator measurements.

NOTE: Write the dial indicator measurements with their positive (+) and negative (-) notation
(signs). This notation is necessary for making the calculations in the chart correctly.

3. Divide the measurement from Step 2 by 2. Write this number on line I in columns (B) & (D).

4. Turn the crankshaft to put the dial indicator at (A). Adjust the dial indicator to "0" (zero).

5. Turn the crankshaft counterclockwise to put the dial indicator at (B). Write the measurements in
the chart.

103 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Checking Bore Runout Of The Flywheel Housing

6. Turn the crankshaft counterclockwise to put the dial indicator at (C). Write the measurement in
the chart.

7. Turn the crankshaft counterclockwise to put the dial indicator at (D). Write the measurement in
the chart.

8. Add lines I and II by columns

9. Subtract the smaller number from the larger number in line III in columns (B) & (D). The result is
the horizontal eccentricity (out of round). Line III, column (C) is the vertical eccentricity.

10. On the graph for total eccentricity find the point of intersection of the lines for vertical
eccentricity and horizontal eccentricity.

104 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

11. If the point of intersection is in the range marked "Acceptable" the bore is in alignment. If the
point of intersection is in the ranged marked "Not Acceptable" the flywheel housing must be
changed.

Graph For Total Eccentricity

(1) Total vertical eccentricity [mm (in)].

(2) Total horizontal eccentricity [mm (in)].

(3) Acceptable.

(4) Not acceptable.

Face Runout (Axial Eccentricity) Of The Flywheel

1. Install the dial indicator as shown. Always put a force on the crankshaft in the same direction
before the indicator is read so the crankshaft end clearance (movement) is always removed.

105 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Checking Face Runout Of The Flywheel

2. Set the dial indicator to read 0.0 mm (.00 in).

3. Turn the flywheel and read the indicator every 90 degrees.

4. The difference between the lower and higher measurements taken at all four points must not be
more than 0.15 mm (.006 in), which is the maximum permissible face runout (axial eccentricity) of
the flywheel.

Bore Runout (Radial Eccentricity) Of The Flywheel

106 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Checking Bore Runout Of The Flywheel

(1) 7H1945 Holding Rod.

(2) 7H1645 Holding Rod.

(3) 7H1942 Indicator.

(4) 7H1940 Universal Attachment.

1. Install the 7H1942 Indicator (3) and make an adjustment of the 7H1940 Universal Attachment (4)
so it makes contact as shown.

2. Set the dial indicator to read 0.0 mm (.00 in).

3. Turn the flywheel and read the indicator every 90 degrees.

4. The difference between the lower and higher measurements taken at all four points must not be
more than ... 0.15 mm (.006 in)

107 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Checking Flywheel Clutch Pilot Bearing Bore

5. Runout (eccentricity) of the bore for the pilot bearing for the flywheel clutch, must not exceed ...
0.13 mm (.005 in)

Vibration Damper
Damage to or failure of the damper will increase vibrations and result in damage to the crankshaft
and may cause more gear train noise at certain engine speeds.

Vibration Damper
(1) Alignment marks.

The vibration damper has marks (1) on the hub and the ring. These marks give an indication of the
condition of the vibration damper. If the marks are not in alignment, the rubber part (between the
ring and the hub) of the vibration damper has had a separation from the ring and/or hub. Install a
new vibration damper.

A used vibration damper can have a visual wobble (movement to the front and then to the rear
when in rotation) on the outer ring and still not need replacement, because some wobble of the

108 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

outer ring is normal. To see if the amount of wobble is acceptable, or replacement is necessary,
check the damper with the procedure that follows:

1. Install a dial indicator, contact point and other parts as necessary to hold the dial indicator
stationary. The contact point must be perpendicular (at a 90 degree angle) to the face of the outer
ring of the damper, and must make contact approximately at the center of the outer ring.

2. Push on the front end of the crankshaft so the end play (free movement on the centerline) is
removed. Keep the crankshaft pushed back until the measurements are done.

3. Adjust the dial indicator to zero.

4. Turn the crankshaft 360 degrees and watch the dial indicator. A total indicator reading of 0.00 to
2.03 mm (.000 to .080 in) is acceptable.

Electrical System
Test Tools For Electrical System

Most of the tests of the electrical system can be done on the engine. The wiring insulation must be
in good condition, the wire and cable connections must be clean and tight, and the battery must be
fully charged. If the on-engine test shows a defect in a component, remove the component for more
testing.

The service manual Testing And Adjusting Electrical Components, REG00636 has complete
specifications and procedures for the components of the starting circuit and the charging circuit.

109 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

The 4C4911 Battery Load Tester is a portable unit in a metal case for use under field conditions and
high temperatures. It can be used to load test all 6, 8 and 12V batteries. This tester has two heavy-
duty load cables that can easily be fastened to the battery terminals. A load adjustment knob on the
top permits the current being drawn from the battery to be adjusted to a maximum of 1000
amperes. The tester is cooled by an internal fan that is automatically activated when a load is
applied.

The tester has a built in LCD digital voltmeter and amperage meter. The digital voltmeter accurately
measures the battery voltage at the battery through tracer wires buried inside the load cables. The
digital amperage meter accurately displays the current being drawn from the battery under test.

NOTE: Make reference to Operating Manual, SEHS9249 for more complete information for use of
the 4C4911 Battery Load Tester.

110 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

8T0900 AC/DC Clamp-On Ammeter

The 8T0900 AC/DC Clamp-On Ammeter is a completely portable, self-contained instrument that
allows electrical current measurements to be made without breaking the circuit or disturbing the
insulation on conductors. A digital display is located on the ammeter for reading current directly in a
range from 1 to 1200 amperes. If an optional 6V6014 Cable is connected between this ammeter
and one of the digital multimeters, current readings of less than 1 ampere can then be read directly
from the display of the multimeter.

A lever is used to open the jaws over the conductor [up to a diameter of 19 mm (.75 in)], and the
spring loaded jaws are then closed around the conductor for current measurement. A trigger switch
that can be locked in the ON or OFF position is used to turn on the ammeter. When the turn-on
trigger is released, the last current reading is held on the display for 5 seconds. This allows
accurate measurements to be taken in limited access areas where the digital display is not visible to
the operator. A zero control is provided for DC operation, and power for the ammeter is supplied by
batteries located inside the handle.

NOTE: Make reference to Special Instruction, SEHS8420 for more complete information for use of
the 8T0900 Clamp-On Ammeter.

111 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

6V7070 Heavy-Duty Digital Multimeter

The 6V7070 Heavy-Duty Digital Multimeter is a completely portable, hand held instrument with a
digital display. This multimeter is built with extra protection against damage in field applications, and
is equipped with seven functions and 29 ranges. The 6V7070 Multimeter has an instant ohms
indicator that permits continuity checks for fast circuit inspection. It also can be used for
troubleshooting small value capacitors.

NOTE: Make reference to Special Instruction, SEHS7734 for more complete information for use of
the 6V7070 Multimeter.

Battery

Never disconnect any charging unit circuit or battery circuit

cable from battery when the charging unit is operated. A spark
can cause an explosion from the flammable vapor mixture of
hydrogen and oxygen that is released from the electrolyte
through the battery outlets. Injury to personnel can be the result.

The battery circuit is an electrical load on the charging unit. The load is variable because of the
condition of the charge in the battery. Damage to the charging unit can result if the connections
(either positive or negative) between the battery and charging unit are broken while the charging
unit is in operation. This is because the battery load is lost and there is an increase in charging
voltage. High voltage can damage, not only the charging unit, but also the regulator and other

112 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

electrical components.

Use the 4C4911 Battery Load Tester, the 8T0900 Clamp-On Ammeter and the 6V7070 Multimeter
to load test a battery that does not hold a charge when in use. Make reference to Special
Instruction, SEHS9249 for the correct procedure and specifications to use.

Charging System
The condition of charge in the battery at each regular inspection will show if the charging system
operates correctly. An adjustment is necessary when the battery is constantly in a low condition of
charge or a large amount of water is needed (more than one ounce of water per cell per week or
per every 100 service hours).

When it is possible, make a test of the charging unit and voltage regulator on the engine, and use
wiring and components that are a permanent part of the system. Off engine (bench) testing will give
a test of the charging unit and voltage regulator operation. This testing will give an indication of
needed repair. After repairs are made, again make a test to give proof that the units are repaired to
their original condition of operation.

Before the start of on engine testing, the charging system and battery must be checked as shown in
the Steps that follow:

1. Battery must be at least 75 percent (1.225 Sp Gr) fully charged and held tightly in place. The
battery holder must not put too much stress on the battery.

2. Cables between the battery, starting motor and engine ground must be the correct size. Wires
and cables must be free of corrosion and have cable support clamps to prevent stress on battery
connections (terminals).

3. Leads, junctions, switches, and panel instruments that have direct relation to the charging circuit
must give correct circuit control.

4. Inspect the drive components for the charging unit to be sure they are free of grease and oil and
have the ability to operate the charging unit.

Alternator Regulator Adjustment

When an alternator is charging the battery too much or not enough, the charging rate of the
alternator should be checked. Make reference to the Specifications module to find all testing
specifications for the alternators and regulators.

No adjustment can be made to change the rate of charge on the alternator regulators. If rate of
charge is not correct, a replacement of the regulator is necessary.

113 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Alternator Pulley Nut Tightening

Tighten the nut that holds the pulley to the specifications given in the Specification Module.

Tools To Tighten Alternator Pulley Nut

(1) 8T9293 Torque Wrench.

(2) 8S1588 Adapter (1/2 inch female to 3/8 inch male).

(3) 2P8267 Socket Assembly.

(4) 8H8517 Combination Wrench (11/8 inch).

(5) 8T5314 Socket.

Starting System
Use the multimeter in the DCV range to find starting system components which do not function.

Move the start control switch to activate the starter solenoid. Starter solenoid operation can be
heard as the pinion of the starting motor is engaged with the ring gear on the engine flywheel.

If the solenoid for the starting motor will not operate, it is possible that the current from the battery
did not get to the solenoid. Fasten one lead of the multimeter to the connection (terminal) for the
battery cable on the solenoid. Put the other lead to a good ground. A zero reading is an indication
that there is a broken circuit from the battery. More testing is necessary when there is a voltage
reading on the multimeter.

The solenoid operation also closes the electric circuit to the motor. Connect one lead of the

114 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

multimeter to the solenoid connection (terminal) that is fastened to the motor. Put the other lead to a
good ground. Activate the starter solenoid and look at the multimeter. A reading of battery voltage
shows the problem is in the motor. The motor must be removed for further testing. A zero reading
on the multimeter shows that the solenoid contacts do not close. This is an indication of the need
for repair to the solenoid or an adjustment to be made to the starter pinion clearance.

Make a test with one multimeter lead fastened to the connection (terminal) for the small wire at the
solenoid and the other lead to the ground. Look at the multimeter and activate the starter solenoid.
A voltage reading shows that the problem is in the solenoid. A zero reading is an indication that the
problem is in the start switch or the wires for the start switch.

Fasten one multimeter lead to the start switch at the connection (terminal) for the wire from the
battery. Fasten the other lead to a good ground. A zero reading indicates a broken circuit from the
battery. Make a check of the circuit breaker and wiring. If there is a voltage reading, the problem is
in the start switch or in the wires for the start switch.

A starting motor that operates too slow can have an overload because of too much friction in the
engine being started. Slow operation of the starting motor can also be caused by a short circuit,
loose connections and/or dirt in the motor.

Pinion Clearance Adjustment

When the solenoid is installed, make an adjustment of the pinion clearance. The adjustment can be
made with the starting motor removed.

Connection For Checking Pinion Clearance

(1) Ground terminal.

115 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

(2) SW terminal.

(3) Connector (from Motor terminal on solenoid to motor).

1. Install the solenoid without connector (3) from the MOTOR connections (terminal) on solenoid to
the motor.

2. Connect a battery, of the same voltage as the solenoid, to the SW terminal (2).

3. Connect the other side of the battery to ground terminal (1).

4. Connect for a moment a wire from the solenoid connection (terminal) marked Motor to the ground
connection (terminal). The pinion will shift to crank position and will stay there until the battery is
disconnected.

Pinion Clearance Adjustment

(4) Adjustment nut.

(5) Pinion.

(6) Pinion clearance.

5. Push the pinion toward the commutator end to remove free movement.

6. Pinion clearance (6) must be 8.3 to 9.9 mm (.33 to .39 in).

7. To adjust pinion clearance, remove plug and turn adjustment nut (4).

8. After the adjustment is completed, install the plug over adjustment nut (4) and install connector
(3) between the Motor terminal on the solenoid and the starting motor.

Rack Shutoff Solenoid

116 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Rack Solenoid
(1) Travel [15.7 mm (.62 in)].

(2) Distance [between shaft and plate 24.4 mm (.96 in)].

(3) Start position of plunger plate from mounting flange is 11.2 mm (.44 in) to measure travel of plunger.

Adjust, if necessary, the distance (2) between the shaft and the plate to 24.4 mm (.96 in) at the start
of the test.

Two checks must be made on the engine to give proof that the solenoid adjustment is correct.

1. The adjustment must give the plunger enough travel to move the rack to the fuel shutoff position.
Use the 9S0240 Rack Position Tool Group to make sure the rack goes to the fuel shutoff position.

2. The adjustment must give the plunger enough travel to cause only the "hold-in" windings of the
solenoid to be activated when the rack is held in the fuel shutoff position. Use a thirty ampere
ammeter to make sure the plunger is in the "hold-in" position. Current needed must be less than
one ampere.

Instruments And Indicators

117 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

Magnetic Pickup

Typical Illustration
(1) Clearance between magnetic pickup and flywheel ring gear ... 0.55 to 0.83 mm (.022 to .033 in)

NOTE: Turn the pickup in until it comes in contact with the teeth on the flywheel ring gear. Turn the
pickup out 1/2 turn. This will give 0.55 to 0.83 mm (.022 to .033 in) clearance at (1).

(2) Tighten the locknut to a torque of ... 25 ± 5 N·m (18 ± 4 lb ft)

Mechanical Indicators For Pressure

Direct Reading Indicator

118 of 119 1/24/2024, 3:43 PM

SIS 2.0 https://sis2.cat.com/#/print-preview/service/6b2a8e07-c8a6-422f-9fd8-...

To check these indicators connect the indicator to a pressure source that can be measured with
accuracy. Make a comparison of pressure on the indicator of test equipment with the pressures on
the direct reading indicator.

PSP-0008379B
2024/01/24
06:40:59+09:00
SENR10280002
© 2024 Caterpillar Inc.

119 of 119 1/24/2024, 3:43 PM