4 508

Electromotoric Actuators SQK34.00

for valves with 90° angle of rotation SQK84.00

• SQK34.00 operating voltage AC 230 V

• SQK84.00 operating voltage AC 24 V
• 3-position control signal
• Nominal angle of rotation 90°
• Nominal torque 5 Nm
• For direct assembly with no need of mounting kit
• 1 auxiliary switch for extra functions
• Manual adjuster and position indicator
• Mode of operation «AUTO» or «MAN»
• Reversible electromotoric actuator

Use

For use in heating, ventilation and air conditioning systems to operate type VBF21…,
VBG31…, VBI31…, VCI31… 3-port and 4-port slipper valves up to DN 50 (refer to
«Equipment combinations»).

CM1N4508en
Building Technologies
22.08.2008 HVAC Products
Type summary

Type Operating voltage Positioning signal Positioning time for 90° at 50 Hz Torque
SQK34.00 AC 230 V
3-position 135 s 5 Nm
SQK84.00 AC 24 V

Accessories Type Description

ASC9.7 Auxiliary switch

Order The actuator and accessories must be ordered separately.

When ordering please specify the quantity, product name and type code.

Example 1 actuator SQK34.00

1 auxiliary switch ASC9.7

Delivery The actuator and accessories are packed separately and delivered as individual items.

Equipment combinations

Slipper valves Actuators SQK34.00, SQK84.00 Data sheet

3-port valve VBF21…, Series 02 DN 40…50 N4241
VBI31…, Series 02 N4232
DN 20…40 (¾…1½“)
VBG31…, Series 02 N4233
4-port valve VCI31…, Series 02 DN 20…40 (¾…1½“) N4252

Function / mechanical design

These electromotoric actuators require no maintenance. They have a reversible

synchronous motor.

The actuator is driven by a 3-position signal from the controller and generates a rotary
motion which is transferred via a pin in the slipper valve shaft to the 3-port or 4-port
slipper valve.

The actuators are supplied with a 90° angle of rotation. During automatic operation,
rotation is limited by two built-in end-switches.

The direction of operation of the actuator can be reversed (refer to «Commissioning»).

Direction of rotation of the actuator on delivery:

• Voltage at Y1 = Counter-clockwise rotation (ccw)
• Voltage at Y2 = Clockwise rotation (cw)
• No voltage = No rotation; actuator fixed in relevant position

1 Position indicator, can be changed manually,

1
depending on the required direction of rotation
2
2 Manual setting knob
When the selector is set to «MAN», the valve can be
operated with a manual knob.
4508Z24

3 Selector for automatic or manual operation

MAN
AUTO

4508Z25

2/6

Building Technologies Electromotoric Actuators CM1N4508en

HVAC Products 22.08.2008
 4 Connecting terminals
5 Coupling and cam shaft
6 Space for auxiliary switch

7 Auxiliary switch ASC9.7

For on / off changeover operation. The switching
point is adjustable.
Factory-wired with a three-wire cable of 1.5 m.

Engineering notes

Electrical installation The actuators must be electrically connected in accordance with local regulations and
with the connection diagrams.

Regulations and requirements to ensure the safety of people and property must
be observed at all times.

If additional functions are required, the actuator must be equipped with an auxiliary
switch. The relevant switching point must be noted in the plant documentation

Mounting notes

Overview of Type Mounting Instructions Type Mounting Instructions

Mounting Instructions SQK34.00, SQK84.00 M4508 74 319 0448 0 ASC9.7 G4508.1 4 319 5579 0

The valve and actuator can be assembled straightforwardly on site. There is no need
for special tools.

Orientation 90° 90°

4716Z16

Commissioning notes

When commissioning the complete motorized valve consisting of actuator and slipper
valve, always check the wiring and test the functions. This also applies to the additional
auxiliary switch ASC9.7 fitted.

For automatic operation, the selector must be set to «AUTO»

Mode of operation

«AUTO» = automatic operation «MAN» = manual operation

3/6

Building Technologies Electromotoric Actuators CM1N4508en

HVAC Products 22.08.2008
Position indication

Manual setting «FULLY CLOSED» Manual setting «FULLY OPEN»

= no supply of heat * = maximum supply of heat *

* If the hydraulic circuit is reverse, the removable scale fort he position indication
must be turned.

Direction of rotation The actuators are factory-set to rotate in counter-clockwise (ccw) direction for opening.
The direction of rotation of the actuator or the slipper valve is determined by the
• Boiler flow (from left or right)
• Position of the slipper valve (hydraulic circuit)

Reversing the
direction of rotation

0 1 0 1
Y2 Y1 N Y2 Y1 N

4508Z30
4508Z31

Control signal supplied to terminal Y1 Control signal supplied to terminal Y2

= counter-clockwise direction (ccw) = clockwise direction (cw)

The wiring connecting terminals Y1 and Y2 must be interchanged if the direction of

rotation is be reversed. If an auxiliary switch is fitted, this aspect must also be taken into
consideration when making the electrical connections.

Setting the The angle of rotation is factory-set to 90° and cannot be adjusted.
angle of rotation

Control Every actuator must be driven by a dedicated controller.

Maintenance

The actuators require no maintenance.

Caution Before performing any service work on the slipper valve or actuator:
• Switch off the pump and power supply
• Close the main shut-off valves in the pipework
• Release pressure in the pipes and allow them to cool down completely
If necessary, disconnect electrical connections from terminals.

The slipper valve must be re-commissioned only with the manual adjuster or the
actuator correctly assembled.

Disposal The actuator contains electrical and electronic components and must not be disposed
of together with domestic waste.
Legislation may demand special handling of certain components, or it may be sensible
from an ecological point of view.
Current local legislation must be observed.

4/6

Building Technologies Electromotoric Actuators CM1N4508en

HVAC Products 22.08.2008
Warranty

The technical data given for these applications is valid only in conjunction with the
Siemens butterfly and slipper valves as detailed under «Equipment combinations».
The use of third-party valves other than those recommended by Siemens invalidates the
warranty.

Technical data

SQK34.00 SQK84.00
Power supply Operating voltage AC 230 V, ± 15 % AC 24 V, ± 20 %
Frequency 50 / 60 Hz
1)
Power consumption 3 VA 2 VA
Control Positioning signal 3-position
Parallel operation parallel operation of several actuators not possible
Operating data Positioning time for 90° 135 s
Angle of rotation 90° ± 3° (factory setting)
1)
Torque Starting torque 10 Nm
Nominal torque 5 Nm
Norms and standards CE-conformity
EMC-directive 2004/108/EC
2)
Immunity EN 61000-6-2 Industrial
Emission EN 61000-6-3 Residential
Low voltage directive 2006/95/EC
Electrical safety EN 60730-1
Product standards for automatic EN 60730-2-14
electric controls
Protection standard EN 60730 Class II Class III
Housing protection standard
Upright to horizontal IP42 to EN 60529
Environmental compatibility ISO 14001 (Environment)
ISO 9001 (Quality)
SN 36350 (Environmentally compatible products)
RL 2002/95/EG (RoHS)
Dimensions / weight Dimensions see «Dimensions»
Cable glands 1 x ∅ 20.5 mm (for M20)
Weight 0.5 kg
Materials Housing base, yoke plastic
Cover plastic
1)
These values apply at nominal voltage, at an ambient temperature of 20 °C and at the specified nominal
running time
2)
Transformer 160 VA (e.g. Siemens 4AM 3842-4TN00-0EA0) for AC 24 V actuators

Accessories for SQK34.00, SQK84.00

Auxiliary switch ASC9.7 Switching capacity AC 250 V, 10 A resistive, 3 A inductive

General Operation Transport Storage

ambient conditions EN 60721-3-3 EN 60721-3-2 EN 60721-3-1
Environmental conditions Class 3K5 Class 2K3 Class 1K3
Temperature –15...+50 °C –30...+65 °C –30...+65 °C
Humidity 5...95 % r. h. < 95 % r. h. 0...95 % r. h.

5/6

Building Technologies Electromotoric Actuators CM1N4508en

HVAC Products 22.08.2008
Internal diagrams

SQK34.00 Y1 Y2 3

M
c1

4508G01
Cm1 Cm2 Cm1 End switch
N 4 5 Cm2 End switch
c1 1 auxiliary switch ASC9.7
N Neutral conductor
G System potential
SQK84.00 Y1 Y2 3 Y1 Control signal counter-clockwise (ccw)
Y2 Control signal clockwise (cw)

M
c1

4508G02
Cm1 Cm2
G 4 5

Dimensions

Dimensions in mm

Overall height of valve = Installation height of slipper valve from the middle of the pipe
and actuator + Installation height of the actuator
+ Minimum clearance from ceiling or wall for mounting, connection,
operation, service etc. f > 100 mm
ff > 200 mm

6/6 © 2008 Siemens Switzerland Ltd Subject to alteration

Building Technologies Electromotoric Actuators CM1N4508en

HVAC Products 22.08.2008