©2023 TP-Link 7106510277 REV4.0.

0
Determine Operation Mode
Refer to the following scenarios to determine an appropriate operation mode.

Scenario I Want To... Operation Mode Mode Switch

The wired network is only limited to one device to connect at a Router (Default Mode) Share ETH
time and I want to share the internet with more wireless devices.
Quick Installation Guide During Travel
I want to turn existing public Wi-Fi into a private network (wired and Hotspot Share Hotspot
AC750 Wi-Fi Travel Router wireless).

I want to turn the existing wired-only network into a wireless network. Access Point
TL-WR902AC
I am in a Wi-Fi "dead zone" or a place with weak wireless signal. I want
Range Extender
At Home to expand an existing Wi-Fi network for a better internet connection. AP/Rng Ext/Client

I have a wired-only device, for example, a smart TV, media player, or Client
game console. I want to connect it to a Wi-Fi network.
Set up with videos
Scan the QR code, or visit
https://www.tp-link.com/download/TL-WR902AC.html#videos

During Travel
Router Mode
3. Check whether the Internet LED is on.
- If yes, skip to Step 6.
Internet
- If no, continue with the steps below.
4. Launch a web browser and enter http://tplinkwifi.net in the address bar. Create a
A password to log in.
http://tplinkwifi.net
B C D
Wired Network
Password

Confirm Password

1. Switch the Mode Switch to Share ETH and connect the hardware from Step A to D. Start
Tip: If you are using a 3G/4G USB modem with a SIM/UIM card, plug the USB modem into the 3G/4G USB port
to transfer the 3G/4G signal to Wi-Fi.

2. Connect your device to the router’s Wi-Fi. The default SSID (network name) and 5. Click Next to start the Quick Setup and then follow the step-by-step web instructions
Wireless Password are printed on the label at the back of the router. to set up the internet connection.
Notes:
Wireless If you are not sure about your WAN Connection Type, click Auto Detect.
Password
/PIN XXXXXXXX You can customize your Wireless Network Name and Password for the 2.4GHz/5GHz wireless network during
the Quick Setup, but you need to reconnect your wireless devices to the new Wi-Fi network(s).
SSID
2.4G: TP-Link_XXXX
5G: TP-Link_XXXX_5G 6. Connect your own devices to the router’s Wi-Fi to enjoy the internet. The WAN/LAN
port functions as the WAN port in this mode.

Hotspot Mode
3. Launch a web browser and enter http://tplinkwifi.net in the address bar. Create a
password to log in.

http://tplinkwifi.net

Password

Confirm Password
Public Hotspot A B Start

4. Click Next to start the Quick Setup and then follow the step-by-step web instructions
to set up the internet connection.
1. Switch the Mode Switch to Share Hotspot and connect the hardware from Step A to B. Notes:
If you are not sure about your WAN Connection Type, use Dynamic IP in most cases or consult the ISP.
2. Connect your device to the router wirelessly or via an Ethernet cable. The default SSID You can customize your Local Network SSID and Password for the 2.4GHz/5GHz wireless network during the
(network name) and Wireless Password are printed on the label at the back of the router. Quick Setup, but you need to reconnect your wireless devices to the new Wi-Fi network(s).

Wireless
Password 5. Connect your own device to the router wirelessly or via an Ethernet cable to enjoy the
/PIN XXXXXXXX
internet. The WAN/LAN port functions as the LAN port in this mode.
SSID
2.4G: TP-Link_XXXX
5G: TP-Link_XXXX_5G

Hardware Information

LED Status Indication Item Description

On/Off The router is on or off. This switch is used to change the operation
(Power) Mode Switch
Blinking The router is initializing or being upgraded. mode of the router.
On/Off The internet is available or unavailable.
This port functions as the WAN port in Router
(Internet) The WAN/LAN port is connected but internet is mode and as the LAN port in Hotspot, Range
Blinking
unavailable when in Router or Access Point mode. WAN/LAN Port Extender and Client modes. This port is for
On The wireless network is enabled. connecting to the existinig router in Access
The router is connecting to the host network Point mode.
(Wireless) Blinking
when in Range Extender or Client mode. POWER Port The port is used to connect the power adapter.
Off The wireless network is disabled.
To reset the router, use a pin to press and hold
On A USB device is connected. RESET Button
(USB) the button until all the LEDs turn off.
Off No USB device is connected.
This port is used for plugging in a 3G/4G
This light stays on for 5 minutes when a WPS 3G/4G USB Port
On modem or USB drive.
connection is established, then goes off.
(WPS)
Blinking WPS connection is in progress. (WPS Button) To establish WPS connection, press this button.
Off No WPS connection is established.
 At Home

Access Point Mode

3. Launch a web browser and enter http://tplinkwifi.net in the address bar. Create a
password to log in.
Internet

http://tplinkwifi.net
Existing Router
Password

LAN Confirm Password

A B C D
Start

1. Switch the Mode Switch to AP/Rng Ext/Client and connect the hardware from Step A to D. 4. Click Next to start the Quick Setup, select Access Point and then follow the
step-by-step web instructions to set up the internet connection.
2. Connect your device to the router’s Wi-Fi. The default SSID (network name) and Wireless
Notes:
Password are printed on the label at the back of the router.
You can customize your Network Name and Password for the 2.4GHz/5GHz wireless network during the Quick
Wireless Setup, but you need to reconnect your wireless devices to the new Wi-Fi network(s).
Password
/PIN XXXXXXXX If you are not sure about the LAN Type of the router, use Smart IP in most cases.
2.4G: TP-Link_XXXX
SSID 5. Connect your own devices to the router’s Wi-Fi to enjoy the internet. The WAN/LAN
5G: TP-Link_XXXX_5G
port is for connecting to the existing router in this mode.

Range Extender Mode

3. Launch a web browser and enter http://tplinkwifi.net in the address bar. Create a
Internet
password to log in.

http://tplinkwifi.net

Password

Confirm Password
A B
Start
Host AP

OR OR
4. Click Next to start the Quick Setup, select Range Extender and then follow the
Desktop Printer Other Device step-by-step web instructions to set up the internet connection.
Notes:
1. Switch the Mode Switch to AP/Rng Ext/Client and connect the hardware from Step A to
You can either copy or customize your SSID (Network Name) during the Quick Setup. The extended network
B near your host AP. shares the same Wi-Fi password as that of your host network.
2. Connect your device to the router wirelessly or via an Ethernet cable. The default SSID If you are not sure about the LAN Type of the router, use Smart IP in most cases.
(network name) and Wireless Password are printed on the label at the back of the router.
5. Relocate the router about halfway between your host AP and the Wi-Fi dead zone.
Wireless

6. Connect your own device to the router wirelessly or via an Ethernet cable to enjoy the
Password
/PIN XXXXXXXX
2.4G: TP-Link_XXXX
internet. The WAN/LAN port functions as the LAN port in this mode.
SSID
5G: TP-Link_XXXX_5G

Client Mode
3. Launch a web browser and enter http://tplinkwifi.net in the address bar. Create a
Internet password to log in.

http://tplinkwifi.net

Password

A Confirm Password
B
Host AP
Start

OR OR

Smart TV Desktop Other Device

4. Click Next to start the Quick Setup, select Client and then follow the step-by-step web
1. Switch the Mode Switch to AP/Rng Ext/Client and connect the hardware from Step A to B instructions to set up the internet connection.
near your host AP. Note: If you are not sure about the LAN Type of the router, use Smart IP in most cases.

2. Connect your device like smartphone, computer or pad to the router wirelessly or via an
Ethernet cable. The default SSID (network name) and Wireless Password are printed on the 5. After the setup, connect your wired-only device like smart TV, game console or media
label at the back of the router. player to the router via an Ethernet cable to enjoy the internet. The WAN/LAN port
Wireless
Password
functions as the LAN port in this mode.
/PIN XXXXXXXX

SSID
2.4G: TP-Link_XXXX
5G: TP-Link_XXXX_5G

Frequently Asked Questions (FAQ) Q4. What should I do if I forget my Wi-Fi password?
• If you have not changed the default wireless password, it can be found on
Safety Information
• Keep the device away from water, fire, humidity or hot environments.
the label of the router. • Do not attempt to disassemble, repair, or modify the device. If you need service,
Q1. What should I do if there is no internet access? • If you have changed the default wireless password, please log in to the please contact us.
• If you are using a cable modem, unplug the Ethernet cable and reboot the router’s web management and go to Wireless 2.4GHz (or Wireless 5GHz) • Do not use damaged charger or USB cable to charge the device.
modem. Wait until its Online LED is on and stable, and then reconnect the > Wireless Security to retrieve or reset your password. • Do not use any other chargers than those recommended.
cable to the modem. • Do not use the device where wireless devices are not allowed.
• If you’re in a hotel room or on a trade show, the internet may be limited
and requires that you authenticate for the service or purchase the
Q5. What should I do if my wireless signal is unstable or too weak? • Adapter shall be installed near the equipment and shall be easily accessible.
internet access. It may be caused by too much interference. Please read and follow the above safety information when operating the device.
• Set your wireless channel to a different one. We cannot guarantee that no accidents or damage will occur due to improper use
• If internet access is still unavailable, contact TP-Link Technical Support.
• Choose a location with less obstacles that may block the signal between of the device. Please use this product with care and operate at your own risk.
the travel router and the host AP. An open corridor or a spacious location is
Q2. How do I restore the router to ideal.
its factory default settings? • Move the router to a new location away from Bluetooth devices and other
• With the router powered on, use a household electronics, such as cordless phones, microwaves, and baby
pin to press and hold the RESET monitors, to minimize signal interference.
button until all the LEDs turn off, • In Range Extender mode, the ideal location to place the router is halfway For technical support, replacement services, user guides, and
and then release the button. between your host AP and the Wi-Fi dead zone. If that is not possible, place other information, please visit https://www.tp-link.com/support,
the router closer to your host AP to ensure stable performance. or simply scan the QR code.

Q3. What should I do if I forget the router’s web management To communicate with TP-Link users or engineers, please join the TP-Link
password? Community at https://community.tp-link.com.
• Refer to FAQ > Q2 to reset the router, then create a password to log in.