UNIVERSAL CALIBRATION SERVICES PVT.

LIMITED, PLOT NO-G-43/1&2, G-44/1&2,

Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 1 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Permanent Facility
ELECTRO-
Using Energy
TECHNICAL-
1 & 3 Phase Energy calibrator, Power
Alternating
1 (240V, 5A & UPF) @ analyzer and energy 1.2 Wh to 100 kWh 1.18 %
Current (< 1
50Hz source by Direct/
GHz)
Comparison method
(Measure)
ELECTRO-
Using 6½ Digital
TECHNICAL-
Multimeter &
Alternating AC Current @
2 Multiproduct 1 A to 10 A 0.20 % to 0.30 %
Current (< 1 (10Hz-1kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)
ELECTRO-
Using 8½ Digital
TECHNICAL-
Multimeter &
Alternating AC Current @
3 Multifunction 10 A to 20 A 0.15 % to 0.12 %
Current (< 1 (10Hz-1kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)
ELECTRO-
Using 6½ Digital
TECHNICAL-
Multimeter &
Alternating AC Current @
4 Multifunction 100 µA to 1 A 0.55 % to 0.20 %
Current (< 1 (10Hz-1kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 2 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
Using 8½ Digital
TECHNICAL-
Multimeter &
Alternating AC Current @
5 Multifunction 1 mA to 200 mA 0.09 % to 0.06 %
Current (< 1 (10Hz-5kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)
ELECTRO-
Using 8½ Digital
TECHNICAL-
Multimeter &
Alternating AC Current @
6 Multifunction 10 µA to 200 µA 0.3 % to 0.05 %
Current (< 1 (10Hz-5kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)
ELECTRO-
Using 8½ Digital
TECHNICAL-
Multimeter &
Alternating AC Current @
7 Multifunction 200 µA to 1 mA 0.05 % to 0.09 %
Current (< 1 (10Hz-5kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)
ELECTRO-
Using 8½ Digital
TECHNICAL-
Multimeter &
Alternating AC Current @
8 Multifunction 200 mA to 10 A 0.06 % to 0.15 %
Current (< 1 (10Hz-5kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)
ELECTRO-
Using 6½ Digital
TECHNICAL-
Multimeter &
Alternating AC Current @
9 Multifunction 100 µA to 1 A 0.55 % to 0.20 %
Current (< 1 (1kHz-5kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 3 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
Using 6½ Digital
TECHNICAL-
Multimeter &
Alternating AC Current @ (1
10 Multifunction 1 A to 3 A 0.20 % to 0.41 %
Current (< 1 kHz-5 kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)
ELECTRO-
Using C.T., 6½
TECHNICAL-
Digital Multimeter &
Alternating AC High Current @
11 Current source by 20 A to 2000 A 2.10 % to 2.40 %
Current (< 1 (50Hz)
Direct/ Comparison
GHz)
method
(Measure)
ELECTRO-
TECHNICAL-
Using HV Divider &
Alternating AC High Current @
12 HV source by Direct/ 1 kV to 20 kV 2.40 % to 2.60 %
Current (< 1 (50Hz)
Comparison method
GHz)
(Measure)
ELECTRO-
Using 8½ Digital
TECHNICAL-
Multimeter &
Alternating AC Voltage @
13 Multifunction 10 mV to 200 mV 0.20 % to 0.025 %
Current (< 1 (10Hz-10kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)
ELECTRO-
Using 8½ Digital
TECHNICAL-
Multimeter &
Alternating AC Voltage @
14 Multifunction 200 mV to 1 V 0.025 % to 0.041 %
Current (< 1 (10Hz-10kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 4 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
Using 6½ Digital
TECHNICAL-
Multimeter &
Alternating AC Voltage @
15 Multifunction 10 mV to 1000 V 0.90 % to 0.15 %
Current (< 1 (10Hz-20kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)
ELECTRO-
Using 8½ Digital
TECHNICAL-
Multimeter &
Alternating AC Voltage @
16 Multifunction 10 mV to 20 V 0.33 % to 0.08 %
Current (< 1 (10kHz-100kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)
ELECTRO-
Using 6½ Digital
TECHNICAL-
Multimeter &
Alternating AC Voltage @
17 Multifunction 10 mV to 700 V 0.75 % to 0.25 %
Current (< 1 (20kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)
ELECTRO-
Using 8½ Digital
TECHNICAL-
Multimeter &
Alternating AC Voltage @ (10
18 Multifunction 1 V to 1000 V 0.041 % to 0.020 %
Current (< 1 Hz-10 kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)
ELECTRO-
Using 8½ Digital
TECHNICAL-
Multimeter &
Alternating AC Voltage @ (10
19 Multifunction 20 V to 100 V 0.08 % to 0.79 %
Current (< 1 kHz-100 kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 5 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
TECHNICAL- Using 6½ Digital
Alternating Capacitance @ Multimeter by
20 1 nF to 10 mF 5.47 % to 1.85 %
Current (< 1 (1kHz) Direct/ Comparison
GHz) method
(Measure)
ELECTRO-
TECHNICAL- Using 6½ Digital
Alternating Capacitance @ Multimeter by
21 10 mF to 100 mF 1.87 % to 4.90 %
Current (< 1 (1kHz) Direct/ Comparison
GHz) method
(Measure)
ELECTRO-
TECHNICAL- Using Multiproduct
AC Current @
22 Alternating Calibrator by Direct 30 µA to 3 A 0.62 % to 0.09 %
(10Hz-1kHz)
Current (< 1 method
GHz) (Source)
ELECTRO-
TECHNICAL- Using Multiproduct
AC Current @
23 Alternating Calibrator by Direct 330 mA to 10 A 0.2 % to 3.5 %
(1kHz-5kHz)
Current (< 1 method
GHz) (Source)
ELECTRO-
Using Multiproduct
TECHNICAL-
AC Current @ Calibrator with
24 Alternating 10 A to 1000 A 0.51 % to 0.61 %
(50Hz-60Hz) Current Coil by
Current (< 1
Direct method
GHz) (Source)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 6 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
TECHNICAL- Using Multiproduct
AC Current @ (1
25 Alternating Calibrator by Direct 30 µA to 330 mA 0.95 % to 1.04 %
kHz-5 kHz)
Current (< 1 method
GHz) (Source)
ELECTRO-
TECHNICAL- Using Multiproduct
AC Current @ (45
26 Alternating Calibrator by Direct 3 A to 20 A 0.09 % to 0.21 %
Hz-1 kHz)
Current (< 1 method
GHz) (Source)
ELECTRO- AC Power (1&3
TECHNICAL- Phase) 50Hz-60Hz/ Using Multiproduct
27 Alternating 0.2pF to 1pF(Lead & Calibrator by Direct 60 mW to 10 kW 1.8 % to 0.38 %
Current (< 1 Lag)/ 30V to 500V/ method
GHz) (Source) 10mA to 20A
ELECTRO-
TECHNICAL- Using Multiproduct
AC Voltage @
28 Alternating Calibrator by Direct 1 mV to 33 V 0.9 % to 0.05 %
(10Hz-45Hz)
Current (< 1 method
GHz) (Source)
ELECTRO-
TECHNICAL- Using Multiproduct
AC Voltage @
29 Alternating Calibrator by Direct 30 mV to 330 mV 0.5 % to 0.15 %
(10kHz-100kHz)
Current (< 1 method
GHz) (Source)
ELECTRO-
TECHNICAL- Using Multiproduct
AC Voltage @
30 Alternating Calibrator by Direct 330 mV to 330 V 0.15 % to 0.32 %
(10kHz-100kHz)
Current (< 1 method
GHz) (Source)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 7 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
TECHNICAL- Using Multiproduct
AC Voltage @
31 Alternating Calibrator by Direct 1 mV to 330 mV 0.8 % to 0.02 %
(45Hz-10kHz)
Current (< 1 method
GHz) (Source)
ELECTRO-
TECHNICAL- Using Multiproduct
AC Voltage @
32 Alternating Calibrator by Direct 330 mV to 1000 V 0.02 % to 0.04 %
(45Hz-10kHz)
Current (< 1 method
GHz) (Source)
ELECTRO-
TECHNICAL- Using Multiproduct
Capacitance @
33 Alternating Calibrator by Direct 220 pF to 330 nF 5.85 % to 0.45 %
(1kHz)
Current (< 1 method
GHz) (Source)
ELECTRO-
TECHNICAL- Using Multiproduct
Capacitance @
34 Alternating Calibrator by Direct 330 nF to 30 mF 0.45 % to 1.5 %
(1kHz)
Current (< 1 method
GHz) (Source)
ELECTRO-
TECHNICAL- Using Inductance
35 Alternating Inductance @ (1kHz) box by Direct 1 mH to 10 H 3%
Current (< 1 Method
GHz) (Source)
ELECTRO- Using 8½ Digital
TECHNICAL- Multimeter &
36 DIRECT DC Current Multifunction 10 µA to 20 mA 0.052 % to 0.003 %
CURRENT Calibrator by Direct/
(Measure) Comparison method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 8 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO- Using 6½ Digital

TECHNICAL- Multimeter &
37 DIRECT DC Current Multifunction 100 µA to 100 mA 0.1 % to 0.07 %
CURRENT Calibrator by Direct/
(Measure) Comparison method
ELECTRO- Using 6½ Digital
TECHNICAL- Multimeter &
38 DIRECT DC Current Multifunction 100 mA to 10 A 0.07 % to 0.2 %
CURRENT Calibrator by Direct/
(Measure) Comparison method
ELECTRO- Using Shunt with 6½
TECHNICAL- Digital Multimeter &
39 DIRECT DC Current current source by 20 A to 100 A 1.76 %
CURRENT Direct/ Comparison
(Measure) method
ELECTRO- Using 8½ Digital
TECHNICAL- Multimeter &
40 DIRECT DC Current Multifunction 20 mA to 20 A 0.003 % to 0.059 %
CURRENT Calibrator by Direct/
(Measure) Comparison method
ELECTRO-
Using HV Divider
TECHNICAL-
with Indicator & HV
41 DIRECT DC High Voltage 1 kV to 20 kV 1.97 % to 2.10 %
source by Direct/
CURRENT
Comparison method
(Measure)
ELECTRO- Using 6½ Digital
TECHNICAL- Multimeter &
42 DIRECT DC Voltage Multifunction 1 mV to 1 V 0.44 % to 0.085 %
CURRENT Calibrator by Direct/
(Measure) Comparison method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 9 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO- Using 6½ Digital

TECHNICAL- Multimeter &
43 DIRECT DC Voltage Multifunction 1 V to 1000 V 0.085 % to 0.006 %
CURRENT Calibrator by Direct/
(Measure) Comparison method
ELECTRO- Using 8½ Digital
TECHNICAL- Multimeter &
44 DIRECT DC Voltage Multifunction 10 µV to 1000 V 5.80 % to 0.0008 %
CURRENT Calibrator by Direct/
(Measure) Comparison method
ELECTRO-
TECHNICAL- Using 6½ Digital
45 DIRECT Resistance (2 Wire) Multimeter by Direct 100 ohm to 1 Gohm 0.07 % to 2.6 %
CURRENT method
(Measure)
ELECTRO-
TECHNICAL- Using 8½ Digital
46 DIRECT Resistance (2 Wire) Multimeter by Direct 2 Mohm to 20 Mohm 0.01 % to 0.0035 %
CURRENT method
(Measure)
ELECTRO-
TECHNICAL- Using 8½ Digital
20 Mohm to 20
47 DIRECT Resistance (2 Wire) Multimeter by Direct 0.0035 % to 0.3 %
Gohm
CURRENT method
(Measure)
ELECTRO-
TECHNICAL- Using 6½ Digital
Resistance (2 Wire/
48 DIRECT Multimeter by Direct 1 ohm to 100 ohm 0.15 % to 0.07 %
4 Wire)
CURRENT method
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 10 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
TECHNICAL- Using 8½ Digital
Resistance (2 Wire/ 100 µohm to 2
49 DIRECT Multimeter by Direct 0.5 % to 0.0015 %
4 Wire) Mohm
CURRENT method
(Measure)
ELECTRO-
TECHNICAL- Using Multiproduct
50 DIRECT DC Current Calibrator by Direct 10 µA to 330 mA 0.25 % to 0.02 %
CURRENT method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
51 DIRECT DC Current Calibrator by Direct 10 A to 20 A 0.07 % to 0.026 %
CURRENT method
(Source)
ELECTRO-
Using Multiproduct
TECHNICAL-
Calibrator with
52 DIRECT DC Current 20 A to 1000 A 0.52 % to 0.64 %
Current Coil by
CURRENT
Direct method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
53 DIRECT DC Current Calibrator by Direct 330 mA to 10 A 0.02 % to 0.07 %
CURRENT method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
54 DIRECT DC Voltage Calibrator by Direct 1 mV to 33 V 0.15 % to 0.002 %
CURRENT method
(Source)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 11 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
TECHNICAL- Using Multiproduct
55 DIRECT DC Voltage Calibrator by Direct 33 V to 1000 V 0.002 % to 0.003 %
CURRENT method
(Source)
ELECTRO-
TECHNICAL- Using Standard
1 Gohm to 200
56 DIRECT Resistance (2 Wire) Resistance box by 3.55 % to 3.79 %
Gohm
CURRENT Direct method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
57 DIRECT Resistance (2 Wire) Calibrator by Direct 1 Mohm to 10 Mohm 0.004 % to 0.03 %
CURRENT method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
10 Mohm to 330
58 DIRECT Resistance (2 Wire) Calibrator by Direct 0.03 % to 0.35 %
Mohm
CURRENT method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
330 Mohm to 1
59 DIRECT Resistance (2 Wire) Calibrator by Direct 0.35 % to 0.2 %
Gohm
CURRENT method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
Resistance (2 Wire/
60 DIRECT Calibrator by Direct 1 µohm to 1 Mohm 0.09 % to 5.77 %
4 Wire)
CURRENT method
(Source)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 12 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
TECHNICAL- Using Multiproduct
61 ELECTRICAL Conductivity meter Calibrator by 0 to 1000 mS/cm 0.061 % to 2.88 %
EQUIPMENT Simulation method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
Oscilloscopes/
62 ELECTRICAL Calibrator by Direct 1 mV to 130 V 4.9 % to 0.35 %
Amplitude
EQUIPMENT method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
Oscilloscopes/Bandw
63 ELECTRICAL Calibrator by Direct 50 kHz to 1.1 GHz 4.85 %
idth
EQUIPMENT method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
64 ELECTRICAL Oscilloscopes/Time Calibrator by Direct 2 ns to 5 s 0.03 % to 0.6 %
EQUIPMENT method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
65 ELECTRICAL pH meter Calibrator by 0 to 14 pH 0.01 pH
EQUIPMENT Simulation method
(Source)
ELECTRO-
TECHNICAL- Power Factor Using Multiproduct
66 ELECTRICAL (Lead/Lag) @ 50 Hz Calibrator by Direct 0.01 PF to 1 PF 0.002 PF
EQUIPMENT /60 Hz method
(Source)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 13 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO- Using 8½ Digital

TECHNICAL- Multimeter &
B-Type
67 TEMPERATURE Multiproduct 100 °C to 1800 °C 0.6 °C
Thermocouple
SIMULATION Calibrator by Direct/
(Measure) Comparison method
ELECTRO- Using 8½ Digital
TECHNICAL- Multimeter &
E-Type -200 °C
68 TEMPERATURE Multiproduct 0.087 °C
Thermocouple to 1000 °C
SIMULATION Calibrator by Direct/
(Measure) Comparison method
ELECTRO- Using 8½ Digital
TECHNICAL- Multimeter &
K-Type
69 TEMPERATURE Multiproduct -200 °C to 1200 °C 0.085 °C
Thermocouple
SIMULATION Calibrator by Direct/
(Measure) Comparison method
ELECTRO- Using 8½ Digital
TECHNICAL- Multimeter &
N-Type
70 TEMPERATURE Multiproduct -200 °C to 1300 °C 0.13 °C
Thermocouple
SIMULATION Calibrator by Direct/
(Measure) Comparison method
ELECTRO- Using 8½ Digital
TECHNICAL- Multimeter &
R-Type
71 TEMPERATURE Multiproduct 0 °C to 1700 °C 0.6 °C
Thermocouple
SIMULATION Calibrator by Direct/
(Measure) Comparison method
ELECTRO-
TECHNICAL- Using 8½ Digital
72 TEMPERATURE RTD Multimeter by Direct -200 °C to 800 °C 0.25 °C
SIMULATION method
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 14 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO- Using 8½ Digital

TECHNICAL- Multimeter &
S-Type
73 TEMPERATURE Multiproduct 0 °C to 1700 °C 0.6 °C
Thermocouple
SIMULATION Calibrator by Direct/
(Measure) Comparison method
ELECTRO- Using 8½ Digital
TECHNICAL- Multimeter &
T-Type
74 TEMPERATURE Multiproduct -200 °C to 400 °C 0.14 °C
Thermocouple
SIMULATION Calibrator by Direct/
(Measure) Comparison method
ELECTRO-
TECHNICAL- Using Multiproduct
B-Type
75 TEMPERATURE Calibrator by Direct 450 °C to 1820 °C 0.8 °C
Thermocouple
SIMULATION method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
E-Type
76 TEMPERATURE Calibrator by Direct -200 °C to 1000 °C 0.15 °C
Thermocouple
SIMULATION method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
J-Type
77 TEMPERATURE Calibrator by Direct -200 °C to 1000 °C 0.6 °C
Thermocouple
SIMULATION method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
K-Type
78 TEMPERATURE Calibrator by Direct -200 °C to 1200 °C 0.6 °C
Thermocouple
SIMULATION method
(Source)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 15 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
TECHNICAL- Using Multiproduct
N-Type
79 TEMPERATURE Calibrator by Direct -200 °C to 1300 °C 0.6 °C
Thermocouple
SIMULATION method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
R-Type
80 TEMPERATURE Calibrator by Direct 100 °C to 1700 °C 0.65 °C
Thermocouple
SIMULATION method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
81 TEMPERATURE RTD Calibrator by Direct -200 °C to 800 °C 0.25 °C
SIMULATION method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
S-Type
82 TEMPERATURE Calibrator by Direct 100 °C to 1700 °C 0.65 °C
Thermocouple
SIMULATION method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
T-Type
83 TEMPERATURE Calibrator by Direct -200 °C to 400 °C 0.21 °C
Thermocouple
SIMULATION method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
84 TIME & Frequency Calibrator by Direct 1 MHz to 10 MHz 0.016 % to 0.06 %
FREQUENCY method
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 16 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO- Using 8½ Digital

TECHNICAL- Multimeter &
85 TIME & Frequency Multiproduct 10 Hz to 1 MHz 0.06 % to 0.006 %
FREQUENCY Calibrator by Direct/
(Measure) Comparison method
ELECTRO- Using 6½ Digital
TECHNICAL- Multimeter &
86 TIME & Frequency Multiproduct 10 Hz to 1000 kHz 0.068 %
FREQUENCY Calibrator by Direct/
(Measure) Comparison method
ELECTRO-
TECHNICAL- Using Time Totalizer
87 TIME & Time by Comparison 2 s to 30 min 0.37 s to 1 s
FREQUENCY method
(Measure)
ELECTRO-
TECHNICAL- Using Time Totalizer
88 TIME & Time by Comparison 30 min to 24 hr 1 s to 104.77 s
FREQUENCY method
(Measure)
ELECTRO-
TECHNICAL- Using Multiproduct
89 TIME & Frequency Calibrator by Direct 1 MHz to 10 MHz 0.08 % to 0.15 %
FREQUENCY method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
90 TIME & Frequency Calibrator by Direct 10 Hz to 1 MHz 0.058 % to 0.08 %
FREQUENCY method
(Source)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 17 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Using Tachometer
MECHANICAL- Speed –RPM (source RPM
>1000 rpm to 4000
91 ACCELERATION Tachometer generator/Calibrator 10 rpm
rpm
AND SPEED (Contact) ) by Comparison
method
Using Tachometer
MECHANICAL- Speed –RPM (source RPM
92 ACCELERATION Tachometer generator/Calibrator 10 rpm to 100 rpm 0.52 rpm
AND SPEED (Contact) ) by Comparison
method
Using Tachometer
MECHANICAL- Speed –RPM (source RPM
100 rpm to 1000
93 ACCELERATION Tachometer generator/Calibrator 3.5 rpm
rpm
AND SPEED (Contact) ) by Comparison
method
Using Tachometer
MECHANICAL- Speed –RPM (source RPM
94 ACCELERATION Tachometer (Non- generator/Calibrator 10 rpm to 100 rpm 0.52 rpm
AND SPEED Contact) ) by Comparison
method
Using Tachometer
MECHANICAL- Speed –RPM (source RPM
100 rpm to 4000
95 ACCELERATION Tachometer (Non- generator/Calibrator 3.7 rpm
rpm
AND SPEED Contact) ) by Comparison
method
Using Tachometer
MECHANICAL- Speed –RPM (source RPM
>4000 rpm to 90000
96 ACCELERATION Tachometer (Non- generator/Calibrator 27.49 rpm
rpm
AND SPEED Contact) ) by Comparison
method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 18 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Using Tachometer
MECHANICAL- (source RPM
97 ACCELERATION Speed RPM of Stirrer generator/Calibrator 10 rpm to 100 rpm 0.52 rpm
AND SPEED ) by Comparison
method
Using Tachometer
MECHANICAL- (source RPM
100 rpm to 4000
98 ACCELERATION Speed RPM of Stirrer generator/Calibrator 3.7 rpm
rpm
AND SPEED ) by Comparison
method
Using Vibration
MECHANICAL- Vibration meter meter calibrator by
99 ACCELERATION Acceleration meter Comparison method 1 m/s² @ 636.6 Hz 0.078 m/s²
AND SPEED @ 636.6 Hz as per ISO :
16063-21
Using Vibration
Vibration meter/
MECHANICAL- meter calibrator by 1 m/s² to 10 m/s² @
Acceleration meter
100 ACCELERATION Comparison method (79.58 Hz & 159.2 0.26 m/s²
@ (79.58 Hz & 159.2
AND SPEED as per ISO : Hz)
Hz)
16063-21
Using Vibration
MECHANICAL- Vibration meter/ meter calibrator by
101 ACCELERATION Acceleration meter Comparison method 1 m/s² @ 15.92 Hz 0.074 m/s²
AND SPEED @ 15.92 Hz as per ISO :
16063-21
Using Sound level
MECHANICAL- Sound Level Meter
102 Generator Calibrator 94 dB & 114 dB 1.8 dB
ACOUSTICS @ 1kHz
by Direct method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 19 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

MECHANICAL- Using Viscosity

103 DENSITY AND Flow cups Standard by 10 cSt to 500 cSt 1%
VISCOSITY Comparison method
MECHANICAL-
DIMENSION
Using 2D Electronics
(BASIC
104 Paddle Gauge Height gauge by Up to 600 mm 10 µm
MEASURING
Comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION Using Video
(BASIC Measuring Machine
105 Templates Up to 200 mm 10 µm
MEASURING by Comparison
INSTRUMENT, method
GAUGE ETC.)
MECHANICAL-
DIMENSION
Using 2D Electronics
(BASIC
106 Width Gauge Height gauge by Up to 600 mm 10 µm
MEASURING
Comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION Using Video
(BASIC Angle/Angle Measuring Machine
107 0° to 360° 4.6 Arc of minute
MEASURING template by Comparison
INSTRUMENT, method
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 20 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

MECHANICAL-
DIMENSION
Using Angle Slip
(BASIC Bevel Protector L.C.-
108 Gauge by 0°-90°-0° 6.5 minute of arc
MEASURING 5 minute
Comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
Bore Gauge with or
DIMENSION
without Dial - Using Dial
(BASIC
109 Transmission stroke Calibration Tester by 0 to 2 mm 3 µm
MEASURING
(All ranges) Comparison method
INSTRUMENT,
L.C-0.001 mm
GAUGE ETC.)
MECHANICAL-
DIMENSION Using Video
(BASIC Measuring Machine
110 CD/PCD Gauge Up to 200 mm 10 µm
MEASURING by Comparison
INSTRUMENT, method
GAUGE ETC.)
MECHANICAL-
DIMENSION
Using 2D Electronics
(BASIC
111 CD/PCD Gauge Height gauge by Up to 600 mm 10 µm
MEASURING
Comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION
Using Coating
(BASIC Coating Thickness
112 Thickness Foils by 0 to 2 mm 5 µm
MEASURING Gauge L.C.-1 µm
Comparison method
INSTRUMENT,
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 21 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

MECHANICAL-
DIMENSION
Using Angle Slip
(BASIC Combination Set
113 Gauge by 0°-90°-0° 35 minute of arc
MEASURING L.C.-1 °
comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION Using Video
(BASIC Measuring Machine
114 Cube mould Up to 200 mm 10 µm
MEASURING by Comparison
INSTRUMENT, method
GAUGE ETC.)
MECHANICAL-
DIMENSION
Using 2D Electronics
(BASIC
115 Cube mould Height gauge by Up to 600 mm 10 µm
MEASURING
Comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION
Using Slip gauge &
(BASIC Depth Micrometer
116 Accessories by 0 to 300 mm 7 µm
MEASURING L.C.- 0.001mm
Comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION
Depth Vernier Using Slip gauge &
(BASIC
117 Caliper L.C.-0.01 Accessories by 0 to 300 mm 15 µm
MEASURING
mm Comparison method
INSTRUMENT,
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 22 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

MECHANICAL-
DIMENSION
Depth Vernier Using Slip gauge &
(BASIC
118 Caliper L.C.-0.02 Accessories by 0 to 600 mm 25 µm
MEASURING
mm Comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION
Dial/Digital Using Slip gauge &
(BASIC
119 Thickness Gauge Accessories by 0 to 1 mm 2 µm
MEASURING
L.C-0.001 mm Comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION
Dial/Digital Using Slip gauge &
(BASIC
120 Thickness Gauge Accessories by 0 to 25 mm 7.60 µm
MEASURING
L.C-0.01 mm Comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION Using Extensometer
(BASIC Extensometer - Calibrator by
121 Up to 5 mm 5 µm
MEASURING Traverse Comparison Method
INSTRUMENT, as per ASTM E-83
GAUGE ETC.)
MECHANICAL- Using Extensometer
DIMENSION Calibrator by
(BASIC Extensometer - Comparison Method
122 Up to 5 mm 5 µm
MEASURING Traverse as per IS : 12872 :
INSTRUMENT, 2021,ISO 9513 :
GAUGE ETC.) 2012

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 23 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

MECHANICAL-
DIMENSION
(BASIC External Micrometer Using Slip Gauge by
123 0 to 100 mm 2 µm
MEASURING L.C.-0.001mm Comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION
Using Slip gauge &
(BASIC External Micrometer >100 mm to 300
124 Accessories by 8 µm
MEASURING L.C.-0.01mm mm
Comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION
Using Slip gauge &
(BASIC External Micrometer >300 mm to 1000
125 Accessories by 15 µm
MEASURING L.C.-0.01mm mm
Comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION
Using probe with
(BASIC
126 Feeler Gauge DRO by Comparison 0.01 mm to 1 mm 2.50 µm
MEASURING
method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
Using Video
DIMENSION
measuring machine
(BASIC
127 Hi-Lo, Limit Gauge & '0' grade slip Up to 200 mm 10 µm
MEASURING
gauge by
INSTRUMENT,
Comparison method
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 24 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

MECHANICAL-
DIMENSION
Using Angle Gauge
(BASIC Inclinometer
128 by Comparison 0°-90°-0° 0.1 °
MEASURING L.C.-0.1°
method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION Using Video
(BASIC Inspection JIG & Measuring Machine
129 Up to 200 mm 10 µm
MEASURING Fixture by Comparison
INSTRUMENT, method
GAUGE ETC.)
MECHANICAL-
DIMENSION
Using 2D Electronics
(BASIC Inspection JIG &
130 Height gauge by Up to 600 mm 10 µm
MEASURING Fixture
Comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION
Using Slip gauge &
(BASIC Internal Micrometer >300 mm to 1000
131 DRO with probe by 13 µm
MEASURING L.C.-0.01 mm mm
Comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION
Using Slip gauge &
(BASIC Internal Micrometer
132 DRO with probe by 0.01 mm to 300 mm 8 µm
MEASURING L.C.-0.01 mm
Comparison method
INSTRUMENT,
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 25 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

MECHANICAL-
DIMENSION
Using Dial
(BASIC Lever Dial L.C.-0.001
133 Calibration Tester by 0 to 2 mm 2 µm
MEASURING mm
Comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION Using probe with
(BASIC Measuring Pin Comparator stand
134 0.10 mm to 20 mm 2 µm
MEASURING Gauge by Comparison
INSTRUMENT, method
GAUGE ETC.)
MECHANICAL-
DIMENSION
Using Tape & Scale
(BASIC Measuring Scale 118xSQRT(L) µm
135 Calibrator by 0 to 2000 mm
MEASURING L.C.-0.5 mm where L in m
Comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION
Using Tape & Scale
(BASIC Measuring Tape/Pie 118xSQRT(L) µm
136 Calibrator by 0 to 100 m
MEASURING Tape L.C: 1 mm where L in m
Comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION
Micrometer Using probe with
(BASIC
137 Head/Drum DRO by comparison 0 to 25 mm 1.50 µm
MEASURING
L.C.-0.001 mm method
INSTRUMENT,
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 26 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

MECHANICAL-
DIMENSION
Using Slip gauge &
(BASIC Micrometer Setting >275 mm to 1000
138 probe with DRO by 9.15 µm
MEASURING Rod/Height Master mm
Comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION
Using Slip gauge &
(BASIC Micrometer Setting
139 probe with DRO by 2 mm to 275 mm 3.50 µm
MEASURING Rod/Height Master
Comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION Using Video
(BASIC Measuring Machine
140 Paddle Gauge Up to 200 mm 10 µm
MEASURING by Comparison
INSTRUMENT, method
GAUGE ETC.)
MECHANICAL-
DIMENSION
Using probe with
(BASIC Paint Thickness
141 DRO by Comparison 0.005 mm to 10 mm 1.50 µm
MEASURING Gauge Foils
method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION
(BASIC Pistol Caliper Using Slip Gauge by
142 0 to 150 mm 60 µm
MEASURING L.C-0.01 mm Comparison method
INSTRUMENT,
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 27 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

MECHANICAL-
Using Length
DIMENSION
Measuring Machine
(BASIC >100 mm to 300
143 Plain Ring Gauge & Master Ring 4 µm
MEASURING mm
Gauge by
INSTRUMENT,
Comparison method
GAUGE ETC.)
MECHANICAL-
Using Length
DIMENSION
Measuring Machine
(BASIC
144 Plain Ring Gauge & Master Ring 3 mm to 100 mm 2 µm
MEASURING
Gauge by
INSTRUMENT,
Comparison method
GAUGE ETC.)
MECHANICAL-
DIMENSION Using Video
(BASIC Measuring Machine
145 Plain work piece Up to 200 mm 10 µm
MEASURING by Comparison
INSTRUMENT, method
GAUGE ETC.)
MECHANICAL-
DIMENSION
Using 2D Electronics
(BASIC
146 Plain work piece Height gauge by Up to 600 mm 10 µm
MEASURING
Comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION
Plain/Paddle Using Slip gauge &
(BASIC >100 mm to 300
147 Plug/Master/Keyway probe with DRO by 4 µm
MEASURING mm
Gauges Comparison method
INSTRUMENT,
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 28 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

MECHANICAL-
DIMENSION
Plain/Paddle Using Slip gauge &
(BASIC
148 Plug/Master/Keyway probe with DRO by 0.50 mm to 100 mm 2.30 µm
MEASURING
Gauges Comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION Using Video
(BASIC Measuring Machine
149 Plated Wire Gauges 0 to 50 mm 6 µm
MEASURING by Comparison
INSTRUMENT, method
GAUGE ETC.)
MECHANICAL-
DIMENSION
Using Dial
(BASIC Plunger Dial
150 Calibration Tester by 0 to 25 mm 3 µm
MEASURING L.C.-0.001 mm
Comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION
(BASIC Plunger Dial Using Slip Gauge by
151 0 to 50 mm 6 µm
MEASURING L.C.-0.001 mm Comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION Precision Spirit Level
Using Electronic
(BASIC Sensitivity 0.02
152 Level by Comparison ±1 mm/m 25 µm/m
MEASURING mm/m Base Length
method
INSTRUMENT, 300 mm
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 29 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

MECHANICAL-
DIMENSION Using Video
(BASIC Radius Gauge/ Measuring Machine
153 0.6 mm to 200 mm 11 µm
MEASURING Radius Template by Comparison
INSTRUMENT, method
GAUGE ETC.)
MECHANICAL-
DIMENSION Using Length
(BASIC Snap Gauge/Gap Measuring Machine
154 100 mm to 300 mm 5 µm
MEASURING Gauge by Comparison
INSTRUMENT, method
GAUGE ETC.)
MECHANICAL-
DIMENSION
(BASIC Snap Gauge/Gap Using Slip Gauge by
155 0.50 mm to 100 mm 3 µm
MEASURING Gauge Comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION
Surface Plates (Cast Using Digital level 2.5xSQRT(L+W/125)
(BASIC 1600 mm x 1000
156 Iron/Granite)- by comparison µm where L and W
MEASURING mm
Flatness method in mm
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION
Using 2D Electronics
(BASIC
157 T gauge Height gauge by Up to 600 mm 10 µm
MEASURING
Comparison method
INSTRUMENT,
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 30 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

MECHANICAL-
DIMENSION Using Video
(BASIC Taper scale L.C.: 0.1 Measuring Machine
158 0.5 mm to 15 mm 9 µm
MEASURING mm by Comparison
INSTRUMENT, method
GAUGE ETC.)
MECHANICAL-
DIMENSION
Using 2D Electronics
(BASIC
159 Templates Height gauge by Up to 600 mm 10 µm
MEASURING
Comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION Using Video
(BASIC Test Sieves Measuring Machine
160 0.01 mm to 125 mm 7 µm
MEASURING (Aperture size) by Comparison
INSTRUMENT, method
GAUGE ETC.)
MECHANICAL-
DIMENSION Using Video
(BASIC Measuring Machine
161 Thread Pitch Gauge 0.4 mm to 6 mm 6.5 µm
MEASURING by Comparison
INSTRUMENT, method
GAUGE ETC.)
MECHANICAL-
DIMENSION Using Length
Thread Plug Gauge
(BASIC Measuring Machine >100 mm to 300
162 (Effective, Minor, 4 µm
MEASURING by Comparison mm
Major Dia)
INSTRUMENT, method
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 31 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

MECHANICAL-
Using Floating
DIMENSION
Thread Plug Gauge Carriage Diameter
(BASIC
163 (Effective, Minor, Measuring machine 2 mm to 100 mm 4 µm
MEASURING
Major Dia) (FCDM m/c) by
INSTRUMENT,
Comparison method
GAUGE ETC.)
MECHANICAL-
Using Length
DIMENSION
Measuring Machine
(BASIC Thread Ring Gauge >100 mm to 300
164 & Master Ring 5 µm
MEASURING (Effective Dia) mm
Gauge by
INSTRUMENT,
Comparison method
GAUGE ETC.)
MECHANICAL-
Using Length
DIMENSION
Measuring Machine
(BASIC Thread Ring Gauge
165 & Master Ring 3 mm to 100 mm 2 µm
MEASURING (Effective Dia)
Gauge by
INSTRUMENT,
Comparison method
GAUGE ETC.)
MECHANICAL-
DIMENSION Tri Using Master square
(BASIC Square/Engineering cylinder, Slip Gauges
166 Up to 600 mm 1.91 µm
MEASURING Square by Comparison
INSTRUMENT, (Straightness) method
GAUGE ETC.)
MECHANICAL-
DIMENSION Using Master square
Tri
(BASIC cylinder, Slip Gauges
167 Square/Engineering Up to 600 mm 15µm
MEASURING by Comparison
Square (Squareness)
INSTRUMENT, method
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 32 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

MECHANICAL-
DIMENSION
Tri Using electronic
(BASIC
168 Square/Engineering probe with DRO by up to 600 mm 1.91 µm
MEASURING
Square (Parallelism) Comparison method
INSTRUMENT,
GAUGE ETC.)
MECHANICAL-
DIMENSION Using Surface Plate,
(BASIC V-Block- Test Mandrels &
169 Up to 200 mm 13 µm
MEASURING Symmetricity probe with DRO by
INSTRUMENT, Comparison method
GAUGE ETC.)
MECHANICAL-
DIMENSION Using Surface Plate,
(BASIC Test Mandrels &
170 V-Block-Parallelism Up to 200 mm 13 µm
MEASURING probe with DRO by
INSTRUMENT, Comparison method
GAUGE ETC.)
MECHANICAL-
DIMENSION Using Square
(BASIC cylinder, Slip gauge
171 V-Block-Squareness Up to 200 mm 13 µm
MEASURING by Comparison
INSTRUMENT, method
GAUGE ETC.)
MECHANICAL-
DIMENSION Vernier Caliper -
Using Slip gauge &
(BASIC Plain, Digital & Dial
172 Accessories by 0 to 1000 mm 17 µm
MEASURING (External, Internal &
comparison method
INSTRUMENT, Depth) L.C.-0.01mm
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 33 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

MECHANICAL-
DIMENSION Using Video
Vickers/Knoop/Rock
(BASIC Measuring Machine
173 well Diamond Cone Up to 200 mm 10 µm
MEASURING by Comparison
Indenter
INSTRUMENT, method
GAUGE ETC.)
MECHANICAL-
DIMENSION Using Video
(BASIC Measuring Machine
174 Welding Fillet Gauge 0 to 60 mm 10 µm
MEASURING by Comparison
INSTRUMENT, method
GAUGE ETC.)
MECHANICAL-
DIMENSION Using Video
(BASIC Measuring Machine
175 Width Gauge Up to 200 mm 10 µm
MEASURING by Comparison
INSTRUMENT, method
GAUGE ETC.)
MECHANICAL-
2D Height Gauge Using Long Slip
DIMENSION
176 (Vernier/Dial/Digital) Gauge by 0 to 1000 mm 10 µm
(PRECISION
L.C.-0.1 µm (Linear) Comparison method
INSTRUMENTS)
MECHANICAL- 2D Height Gauge
Using Master square
DIMENSION (Vernier/Dial/Digital)
177 cylinder by 0 to 1000 mm 5.20 µm
(PRECISION L.C.-0.1 µm
comapsrison method
INSTRUMENTS) (Squareness)
MECHANICAL-
Using probe with
DIMENSION Dial Calibration
178 DRO by Comparison 0 to 25 mm 1.5 µm
(PRECISION Tester L.C.0.1 µm
method
INSTRUMENTS)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 34 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

MECHANICAL- Electronic Probe

Using Slip Gauge set
DIMENSION With DRO /
179 by Comparision 0 to 25 mm 1 µm
(PRECISION Comparator/LVDT
method
INSTRUMENTS) L.C.-0.0001 mm
Using Slip Gauges,
MECHANICAL-
Comparator stand
DIMENSION
180 LVDT L.C: 0.001 mm and Digital 0 to 100 mm 10 µm
(PRECISION
Multimeter by
INSTRUMENTS)
Comparison method
MECHANICAL- Using Surface
DIMENSION Surface Roughness Roughness Master
181 0.1 µm to 3 µm 10 %
(PRECISION Tester (Ra) by Comparison
INSTRUMENTS) method
MECHANICAL-
Video Measuring Using Glass graticule
DIMENSION
182 Machine ( Angular ) by comparison 0 ° to 360 ° 15 s
(PRECISION
L.C.: 1 arc second Method
INSTRUMENTS)
MECHANICAL- Video Measuring
DIMENSION Machine/Microscope Using Glass scale by
183 0 to 200 mm 3 µm
(PRECISION ( Linear ) L.C.: comparison Method
INSTRUMENTS) 0.0001 mm
Using Dial
Calibration Tester by 10 Shore A/D/AO/AM
MECHANICAL- 0.9 Shore
184 Durometer Depth of Indentor as to 100 Shore
DUROMETER A/D/AO/AM
per ISO 18898 : A/D/AO/AM
2016
MECHANICAL- Using Slotted mass
MOBILE FORCE Push-Pull With hanger as per
185 5 N to 500 N 1.5 N
MEASURING Gauge/Force Gauge VDI/VDE 2624 Part
SYSTEM 2.1

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 35 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Hydraulic Pressure Using Digital

Dial and Digital pressure Calibrator ,
MECHANICAL- Pressure Gauges, 6½ Digital
PRESSURE Pressure Multimeter,
186 >400 bar to 700 bar 0.56 bar
INDICATING Transmitters, Hydraulic pressure
DEVICES Transducers, pump as per DKD-R
Pressure Switches 6-1 by Comparison
(Medium:Hydraulic) method
Hydraulic Pressure Using Digital
Dial and Digital pressure Calibrator,
MECHANICAL- Pressure Gauges, 6½ Digital
PRESSURE Pressure Multimeter,
187 30 bar to 400 bar 0.15 bar
INDICATING Transmitters, Hydraulic pressure
DEVICES Transducers, pump as per DKD-R
Pressure Switches 6-1 by Comparison
(Medium:Hydraulic) method
Pneumatic Pressure
Using Digital
Dial and Digital
pressure Calibrator,
Pressure Gauges,
MECHANICAL- 6½ Digital
Magnehelic gauges,
PRESSURE Multimeter, >20 mbar to 200
188 Pressure 0.13 mbar
INDICATING Pneumatic pressure mbar
Transmitter,
DEVICES pump as per DKD-R
Transducers,
6-1 by Comparison
Pressure Switch
method
(Medium:Pneumatic)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 36 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Pneumatic Pressure
Using Digital
Dial and Digital
pressure Calibrator,
Pressure Gauges,
MECHANICAL- 6½ Digital
Pressure
PRESSURE Multimeter
189 Transmitters, >0.2 bar to 1 bar 0.00086 bar
INDICATING ,Pneumatic pressure
Transducers,
DEVICES pump as per DKD-R
Pressure Switches
6-1 by Comparison
(Medium:
method
Pneumatic)
Pneumatic Pressure
Using Digital
Dial and Digital
pressure Calibrator ,
Pressure Gauges,
MECHANICAL- 6½ Digital
Pressure
PRESSURE Multimeter,
190 Transmitters, >1 bar to 30 bar 0.011 bar
INDICATING Pneumatic pressure
Transducers,
DEVICES pump as per DKD-R
Pressure Switches
6-1 by Comparison
(Medium
method
:Pneumatic)
Pneumatic Pressure
Using Digital
Digital and Dial
pressure
Pressure Gauges,
Calibrator/gauge,
MECHANICAL- Magnehelic gauges,
6½ Digital
PRESSURE Pressure
191 Multimeter & 0 to 20 mbar 0.01 mbar
INDICATING Transducers,
Pneumatic pressure
DEVICES Transmitters,
pump as per DKD-R
Pressure Switch
6-1 by Comparison
(Medium:
method
Pneumatic)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 37 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Pneumatic Vacuum Using Digital

Dial and Digital Vacuum Calibrator ,
MECHANICAL- Vacuum Gauges, 6½ Digital
PRESSURE Vacuum Multimeter,
192 -0.93 bar to 0 0.00064 bar
INDICATING Transmitters,Transd Pneumatic pressure
DEVICES ucers, Vacuum pump as per DKD-R
Switches 6-1 by Comparison
(Medium:Pneumatic) method
Pressure Dial and
Using Hydraulic
Digital Pressure
MECHANICAL- Dead Weight Tester
Gauges, Pressure
PRESSURE Calibrator, 6½
193 Transmitters, 0 to 35 bar 0.01 bar
INDICATING Digital Multimeter as
Transducers,
DEVICES per DKD-R 6-1 by
Pressure Switches
Comparison method
(Medium:Hydraulic)
Pressure Dial and
Using Hydraulic
Digital Pressure
MECHANICAL- Dead Weight Tester
Gauges, Pressure
PRESSURE Calibrator , 6½
194 Transmitters, 35 bar to 700 bar 0.12 bar
INDICATING Digital Multimeter as
Transducers,
DEVICES per DKD-R 6-1 by
Pressure Switches
Comparison method
(Medium:Hydraulic)
MECHANICAL- Torque Tools - Using Torque Sensor
TORQUE Pneumatic, with indicator as per
195 1 Nm to 10 Nm 0.44 %
GENERATING Electrical, Hydraulic IS 15411 : 2003 /
DEVICES and Oil Pulse Tools ISO 5393 :1994
MECHANICAL- Torque Tools - Using Torque Sensor
TORQUE Pneumatic, with Indicator as per
196 10 Nm to 50 Nm 0.8 %
GENERATING Electrical, Hydraulic IS 15411 : 2003 /
DEVICES and Oil Pulse Tools ISO 5393 : 1994

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 38 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

MECHANICAL- Torque Wrenches Using Torque sensor

TORQUE Type l Class with indicator &
197 2 Nm to 20 Nm 2.05 %rdg
GENERATING A,B,C,D,E & Type II Calibrator as per IS
DEVICES Class A,B,C,D,E,F,G 16906:2018
MECHANICAL- Torque Wrenches Using Torque sensor
TORQUE Type l Class with indicator &
198 20 Nm to 200 Nm 1.58 %rdg
GENERATING A,B,C,D,E & Type II Calibrator as per IS
DEVICES Class A,B,C,D,E,F,G 16906:2018
MECHANICAL- Torque Wrenches Using Torque sensor
TORQUE Type l Class with indicator &
199 200 Nm to 2000 Nm 1.75 %rdg
GENERATING A,B,C,D,E & Type II Calibrator as per IS
DEVICES Class A,B,C,D,E,F,G 16906:2018
Volume Glass Using Weighing
Burette /Measuring balance with d : 0.01
cylinder /volumetric mg and distilled
MECHANICAL-
200 flask /Conical flask/ water based on 1 ml to 10 ml 0.19 ml
VOLUME
Beaker-Single Gravimetric method
marking & as per IS/ISO 4787 &
graduated ISO/TR 20461
Using Weighing
Volume Glass
balance with d : 0.01
Burette /Measuring
mg / 0.1 mg and
cylinder /volumetric
MECHANICAL- distilled water based
201 flask /Conical flask/ 10 ml to 50 ml 0.51 ml
VOLUME on Gravimetric
Beaker-Single
method as per
marking &
IS/ISO 4787 &
graduated
ISO/TR 20461

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 39 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Using Weighing
Volume Glass
balance with d : 0.01
Burette /Measuring
mg / 0.1 mg / 1 mg
cylinder /volumetric
MECHANICAL- and distilled water
202 flask /Conical flask/ 100 ml to 500 ml 2.2 ml
VOLUME based on
Beaker-Single
Gravimetric method
marking &
as per IS/ISO 4787 &
graduated
ISO/TR 20461
Using Weighing
Volume Glass
balance with d : 0.01
Burette /Measuring
mg / 0.1 mg and
cylinder /volumetric
MECHANICAL- distilled water based
203 flask /Conical flask/ 50 ml to 100 ml 0.51 ml
VOLUME on Gravimetric
Beaker-Single
method as per
marking &
IS/ISO 4787 &
graduated
ISO/TR 20461
Volume Glass Using Weighing
Burette /Measuring balance with d : 1
cylinder /volumetric mg and distilled
MECHANICAL-
204 flask /Conical flask/ water based on 500 ml to 1000 ml 2.6 ml
VOLUME
Beaker-Single Gravimetric method
marking & as per IS/ISO 4787 &
graduated ISO/TR 20461
Using Weighing
Volume Micro balance with d : 0.01
pipettes -Piston mg and distilled
MECHANICAL-
205 operated/Glass water based on 10 µl to 100 µl 0.5 µl
VOLUME
Single marking & Gravimetric method
graduated as per ISO 8655 – 6
& ISO/TR 20461

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 40 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Using Weighing
Volume Micro balance with d : 0.01
pipettes -Piston mg and distilled
MECHANICAL-
206 operated/Glass water based on 100 µl to 1000 µl 2.54 µl
VOLUME
Single marking & Gravimetric method
graduated as per ISO 8655 – 6
& ISO/TR 20461
MECHANICAL- Electronic weighing Using standard
WEIGHING balance (Class I & weights E1 class
207 0 to 82 g 0.03 mg
SCALE AND Coarser) Readability weights as per OIML
BALANCE :0.01 mg R-76-1
MECHANICAL- Electronic weighing Using standard
WEIGHING balance (Class I & weights E1 class
208 0 to 220 g 0.22 mg
SCALE AND Coarser) Readability weights as per OIML
BALANCE :0.1 mg R-76-1
MECHANICAL- Electronic weighing
Using standard F1
WEIGHING balance (Class II &
209 class weights as per 0 to 2.2 kg 30 mg
SCALE AND Coarser )
OIML R-76-1
BALANCE Readability:10 mg
MECHANICAL- Electronic weighing
Using standard F1
WEIGHING balance (Class II &
210 class weights as per 0 to 32.2 kg 250 mg
SCALE AND Coarser) Readability
OIML R-76-1
BALANCE :100 mg
MECHANICAL- Electronic weighing
Using standard E2 &
WEIGHING balance (Class II &
211 F1 class weights as 0 to 1.02 kg 3.0 mg
SCALE AND Coarser)
per OIML R-76-1
BALANCE Readability:1 mg

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 41 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Using E1 class
standard weights &
MECHANICAL- Weight- F2 Class
212 Balance of d : 0.01 200 mg 0.025 mg
WEIGHTS Weight and coarser
mg by ABBA Method
as per OIML R-111
Using E1 class
standard weights &
MECHANICAL- Weight: F1 Class
213 Balance of d : 0.01 5g 0.025 mg
WEIGHTS Weight and coarser
mg by ABBA Method
as per OIML R-111
Using E1 class
standard weights &
MECHANICAL- Weight: F1 Class
214 Balance of d : 0.01 500 mg 0.025 mg
WEIGHTS Weights and coarser
mg by ABBA Method
as per OIML R-111
Using E1 class
standard weights &
MECHANICAL- Weight: F1 Class
215 Balance of d : 0.01 50 g 0.03 mg
WEIGHTS Weights and coarser
mg by ABBA Method
as per OIML R-111
Using F1 class
standard weights &
MECHANICAL- Weight: M1 Class
216 Balance of d : 1 mg 500 g 3.0 mg
WEIGHTS Weight and coarser
by ABBA Method as
per OIML R-111
Using E1 class
standard weights &
MECHANICAL- Weight:F1 Class
217 Balance of d : 0.01 20 g 0.03 mg
WEIGHTS Weight and coarser
mg by ABBA Method
as per OIML R-111

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 42 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Using E1 class
standard weights &
MECHANICAL- Weight:F1 Class
218 Balance of d : 0.01 1g 0.025 mg
WEIGHTS Weight and coarser
mg by ABBA Method
as per OIML R-111
Using E1 class
standard weights &
MECHANICAL- Weight:F2 Class
219 Balance of d : 0.01 10 mg 0.0092 mg
WEIGHTS Weight and coarser
mg by ABBA Method
as per OIML R-111
Using E1 class
standard weights &
MECHANICAL- Weights :F1 Class
220 Balance of d : 0.01 10 g 0.02 mg
WEIGHTS Weights and coarser
mg by ABBA Method
as per OIML R-111
Using F1 class
standard weights &
MECHANICAL- Weights :F2 Class
221 Balance of d : 10 mg 2 kg 10.0 mg
WEIGHTS Weights and coarser
by ABBA Method as
per OIML R-111
Using F1 class
standard weights &
MECHANICAL- Weights :M1 Class
222 Balance of d : 100 20 kg 100.0 mg
WEIGHTS Weights and coarser
mg by ABBA Method
as per OIML R-111
Using F1 class
standard weights &
MECHANICAL- Weights- M1 Class
223 Balance of d : 100 10 kg 143.0 mg
WEIGHTS Weights and coarser
mg by ABBA Method
as per OIML R-111

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 43 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Using E1 class
standard weights &
MECHANICAL- Weights: F1 Class
224 Balance of d : 0.01 50 mg 0.01 mg
WEIGHTS Weights and coarser
mg by ABBA Method
as per OIML R-111
Using E1 class
standard weights &
MECHANICAL- Weights: F1 Class
225 Balance of d : 0.1 100 g 0.15 mg
WEIGHTS Weights and coarser
mg by ABBA Method
as per OIML R-111
Using E1 class
standard weights &
MECHANICAL- Weights: F1 Class
226 Balance of d : 0.01 100 mg 0.0096 mg
WEIGHTS Weights and coarser
mg by ABBA Method
as per OIML R-111
Using E1 class
standard weights &
MECHANICAL- Weights: F1 Class
227 Balance of d : 0.01 20 mg 0.009 mg
WEIGHTS Weights and coarser
mg by ABBA Method
as per OIML R-111
Using F1 class
standard weights &
MECHANICAL- Weights: F2 Class
228 Balance of d : 1 mg 1 kg 5.0 mg
WEIGHTS Weights and coarser
by ABBA Method as
per OIML R-111
Using E1 class
standard weights &
MECHANICAL- Weights: F2 Class
229 Balance of d : 0.01 2 mg 0.009 mg
WEIGHTS Weights and coarser
mg by ABBA Method
as per OIML R-111

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 44 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Using E1 class
standard weights &
MECHANICAL- Weights: F2 Class
230 Balance of d : 0.01 1 mg 0.009 mg
WEIGHTS Weights and coarser
mg by ABBA Method
as per OIML R-111
Using E1class
standard weights &
MECHANICAL- Weights: F2 Class
231 Balance of d : 0.01 5 mg 0.009 mg
WEIGHTS Weights and coarser
mg by ABBA Method
as per OIML R-111
Using F1 class
standard weights &
MECHANICAL- Weights: M2 Class
232 Balance of d : 100 5 kg 100.0 mg
WEIGHTS Weights and coarser
mg by ABBA Method
as per OIML R-111
Using E1 class
standard weights &
MECHANICAL- Weights:F1 Class
233 Balance of d : 0.01 2g 0.025 mg
WEIGHTS Weights and coarser
mg by ABBA Method
as per OIML R-111
Using E1 class
standard weights &
MECHANICAL- Weights:F1 Class
234 Balance of d : 0.1 200 g 0.131 mg
WEIGHTS Weights and coarser
mg by ABBA Method
as per OIML R-111

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 45 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Humidity &
Temperature Sensor
Using Temperature
with Indicator of
& Humidity meter,
THERMAL- Transducer/Transmit
source Humidity 20 %rh to 95 %rh
235 SPECIFIC HEAT ter with 2 %rh
Generator/Calibrator @20°C to 35°C
& HUMIDITY Indicator/Digital
with probe by
thermo
Comparison method
hygrometer/Data
logger
Humidity&
Temperature
Using Temperature
indicator with sensor
& Humidity meter
THERMAL- of environmental,
(source Humidity 20 %rh to 95 %rh
236 SPECIFIC HEAT Climatic, Humidity 2 %rh
Generator/Calibrator @20°C to 50°C
& HUMIDITY Chamber/calibrator
) with probe by
(Relative Humidity
Comparison method
at a specified Single
Position )
Humidity&
Temperature Sensor Using RTD & 6½
with indicator of Digital Multimeter,
THERMAL- Transducer/Transmit source Humidity/
5 °C to 50 °C @50%
237 SPECIFIC HEAT ter with Temperature 0.30 °C
rh
& HUMIDITY Indicator/Digital Generator/Calibrator
thermo by Comparison
hygrometer/Data method
logger

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 46 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Humidity&
Temperature Sensor
Using Temperature
with Indicator of
& Humidity meter
THERMAL- Transducer/Transmit
(source Humidity 20 %rh to 50 %rh
238 SPECIFIC HEAT ter with 2 %rh
Generator/Calibrator @35°C to 50°C
& HUMIDITY Indicator/Digital
) with probe by
thermo
Comparison method
hygrometer/Data
logger
Using R-Type
THERMAL- Thermocouple, DAQ
239 Dry Block Calibrators 600 °C to 1200 °C 1.30 °C
TEMPERATURE Temp scanner as per
EURAMET cg -13
Using RTD (Pt-100),
6½ Digital
Indicator with sensor
Multimeter /
THERMAL- of Liquid Baths/ Dry
240 Temperature 140 °C to 600 °C 0.4 °C
TEMPERATURE Block Calibrators
indicator/Calibrator
(Single Position)
by Comparison
method
Using RTD (Pt-100),
6½ Digital
Indicator with sensor
Multimeter /
THERMAL- of Liquid Baths/ Dry
241 Temperature -35 °C to 140 °C 0.1 °C
TEMPERATURE Block Calibrators
indicator/Calibrator
(Single Position)
by Comparison
method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 47 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Using Master Non

IR /Non Contact contact
THERMAL- Digital thermometer, Black
242 0 °C to 100 °C 2.75 °C
TEMPERATURE Thermometer/Gun/ body source
Pyrometer (emissivity 0.95)by
Comparison method
Using Master Non
IR /Non Contact contact
THERMAL- Digital thermometer, Black
243 100 °C to 500 °C 2.89 °C
TEMPERATURE Thermometer/Gun/ body source
Pyrometer (emissivity 0.95)by
Comparison method
Using RTD (Pt-100),
Liquid in Glass 6½ Digital
THERMAL-
244 thermometer / Dial Multimeter & Liquid 140 °C to 250 °C 0.68 °C
TEMPERATURE
thermometer bath by Comparison
method
Using RTD (Pt-100),
Liquid in Glass 6½ Digital
THERMAL-
245 thermometer / Dial Multimeter & Liquid -35 °C to 140 °C 0.2 °C
TEMPERATURE
thermometer bath by Comparison
method
RTD/Thermocouple / Using RTD (Pt-100),
Sensor with or 6½ Digital
THERMAL-
246 without temperature Multimeter & /Dry -35 °C to 140 °C 0.05 °C
TEMPERATURE
Indicator/ Data bath by Comparison
logger / Recorder method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 48 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

RTD/Thermocouple / Using RTD (Pt-100),

Sensor with or 6½ Digital
THERMAL-
247 without temperature Multimeter, Dry 140 °C to 600 °C 0.30 °C
TEMPERATURE
Indicator/ Data block by Comparison
logger / Recorder method
Using R-Type
Thermocouple/
Thermocouple, 6½
sensor with or
Digital Multimeter,
THERMAL- without,
248 Temperature 600 °C to 1200 °C 1.28 °C
TEMPERATURE temperature
indicator/ calibrator
Indicator/ Data
& Dry block by
logger/ Recorder
Comparison method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 49 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Site Facility
ELECTRO-
Using Energy
TECHNICAL-
1 & 3 Phase Energy calibrator, Power
Alternating
1 (240V, 5A & UPF) @ analyzer and energy 1.2 Wh to 100 kWh 1.18 %
Current (< 1
50Hz source by Direct/
GHz)
Comparison method
(Measure)
ELECTRO-
Using 6½ Digital
TECHNICAL-
Multimeter &
Alternating AC Current @
2 Multiproduct 1 A to 10 A 0.20 % to 0.30 %
Current (< 1 (10Hz-1kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)
ELECTRO-
Using 8½ Digital
TECHNICAL-
Multimeter &
Alternating AC Current @
3 Multifunction 10 A to 20 A 0.15 % to 0.12 %
Current (< 1 (10Hz-1kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)
ELECTRO-
Using 6½ Digital
TECHNICAL-
Multimeter &
Alternating AC Current @
4 Multifunction 100 µA to 1 A 0.55 % to 0.20 %
Current (< 1 (10Hz-1kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 50 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
Using 8½ Digital
TECHNICAL-
Multimeter &
Alternating AC Current @
5 Multifunction 1 mA to 200 mA 0.09 % to 0.06 %
Current (< 1 (10Hz-5kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)
ELECTRO-
Using 8½ Digital
TECHNICAL-
Multimeter &
Alternating AC Current @
6 Multifunction 10 µA to 200 µA 0.3 % to 0.05 %
Current (< 1 (10Hz-5kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)
ELECTRO-
Using 8½ Digital
TECHNICAL-
Multimeter &
Alternating AC Current @
7 Multifunction 200 µA to 1 mA 0.05 % to 0.09 %
Current (< 1 (10Hz-5kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)
ELECTRO-
Using 8½ Digital
TECHNICAL-
Multimeter &
Alternating AC Current @
8 Multifunction 200 mA to 10 A 0.06 % to 0.15 %
Current (< 1 (10Hz-5kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)
ELECTRO-
Using 6½ Digital
TECHNICAL-
Multimeter &
Alternating AC Current @
9 Multifunction 100 µA to 1 A 0.55 % to 0.20 %
Current (< 1 (1kHz-5kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 51 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
Using 6½ Digital
TECHNICAL-
Multimeter &
Alternating AC Current @ (1
10 Multifunction 1 A to 3 A 0.20 % to 0.41 %
Current (< 1 kHz-5 kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)
ELECTRO-
Using C.T., 6½
TECHNICAL-
Digital Multimeter &
Alternating AC High Current @
11 Current source by 20 A to 2000 A 2.10 % to 2.40 %
Current (< 1 (50Hz)
Direct/ Comparison
GHz)
method
(Measure)
ELECTRO-
TECHNICAL-
Using HV Divider &
Alternating AC High Current @
12 HV source by Direct/ 1 kV to 20 kV 2.40 % to 2.60 %
Current (< 1 (50Hz)
Comparison method
GHz)
(Measure)
ELECTRO-
TECHNICAL-
Alternating AC High Voltage @ Using HV Divider by
13 20 kV to 100 kV 2.60 % to 4.05 %
Current (< 1 (50Hz) Direct method
GHz)
(Measure)
ELECTRO-
Using 8½ Digital
TECHNICAL-
Multimeter &
Alternating AC Voltage @
14 Multifunction 10 mV to 200 mV 0.20 % to 0.025 %
Current (< 1 (10Hz-10kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 52 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
Using 8½ Digital
TECHNICAL-
Multimeter &
Alternating AC Voltage @
15 Multifunction 200 mV to 1 V 0.025 % to 0.041 %
Current (< 1 (10Hz-10kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)
ELECTRO-
Using 6½ Digital
TECHNICAL-
Multimeter &
Alternating AC Voltage @
16 Multifunction 10 mV to 1000 V 0.90 % to 0.15 %
Current (< 1 (10Hz-20kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)
ELECTRO-
Using 8½ Digital
TECHNICAL-
Multimeter &
Alternating AC Voltage @
17 Multifunction 10 mV to 20 V 0.33 % to 0.08 %
Current (< 1 (10kHz-100kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)
ELECTRO-
Using 6½ Digital
TECHNICAL-
Multimeter &
Alternating AC Voltage @
18 Multifunction 10 mV to 700 V 0.75 % to 0.25 %
Current (< 1 (20kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)
ELECTRO-
Using 8½ Digital
TECHNICAL-
Multimeter &
Alternating AC Voltage @ (10
19 Multifunction 1 V to 1000 V 0.041 % to 0.020 %
Current (< 1 Hz-10 kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 53 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
Using 8½ Digital
TECHNICAL-
Multimeter &
Alternating AC Voltage @ (10
20 Multifunction 20 V to 100 V 0.08 % to 0.79 %
Current (< 1 kHz-100 kHz)
Calibrator by Direct/
GHz)
Comparison method
(Measure)
ELECTRO-
TECHNICAL- Using 6½ Digital
Alternating Capacitance @ Multimeter by
21 1 nF to 10 mF 5.47 % to 1.85 %
Current (< 1 (1kHz) Direct/ Comparison
GHz) method
(Measure)
ELECTRO-
TECHNICAL- Using 6½ Digital
Alternating Capacitance @ Multimeter by
22 10 mF to 100 mF 1.87 % to 4.90 %
Current (< 1 (1kHz) Direct/ Comparison
GHz) method
(Measure)
ELECTRO-
TECHNICAL- Using Multiproduct
AC Current @
23 Alternating Calibrator by Direct 30 µA to 3 A 0.62 % to 0.09 %
(10Hz-1kHz)
Current (< 1 method
GHz) (Source)
ELECTRO-
TECHNICAL- Using Multiproduct
AC Current @
24 Alternating Calibrator by Direct 330 mA to 10 A 0.2 % to 3.5 %
(1kHz-5kHz)
Current (< 1 method
GHz) (Source)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 54 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
Using Multiproduct
TECHNICAL-
AC Current @ Calibrator with
25 Alternating 10 A to 1000 A 0.51 % to 0.61 %
(50Hz-60Hz) Current Coil by
Current (< 1
Direct method
GHz) (Source)
ELECTRO-
TECHNICAL- Using Multiproduct
AC Current @ (1
26 Alternating Calibrator by Direct 30 µA to 330 mA 0.95 % to 1.04 %
kHz-5 kHz)
Current (< 1 method
GHz) (Source)
ELECTRO-
TECHNICAL- Using Multiproduct
AC Current @ (45
27 Alternating Calibrator by Direct 3 A to 20 A 0.09 % to 0.21 %
Hz-1 kHz)
Current (< 1 method
GHz) (Source)
ELECTRO- AC Power (1&3
TECHNICAL- Phase) 50Hz-60Hz/ Using Multiproduct
28 Alternating 0.2pF to 1pF(Lead & Calibrator by Direct 60 mW to 10 kW 1.8 % to 0.38 %
Current (< 1 Lag)/ 30V to 500V/ method
GHz) (Source) 10mA to 20A
ELECTRO-
TECHNICAL- Using Multiproduct
AC Voltage @
29 Alternating Calibrator by Direct 1 mV to 33 V 0.9 % to 0.05 %
(10Hz-45Hz)
Current (< 1 method
GHz) (Source)
ELECTRO-
TECHNICAL- Using Multiproduct
AC Voltage @
30 Alternating Calibrator by Direct 30 mV to 330 mV 0.5 % to 0.15 %
(10kHz-100kHz)
Current (< 1 method
GHz) (Source)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 55 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
TECHNICAL- Using Multiproduct
AC Voltage @
31 Alternating Calibrator by Direct 330 mV to 330 V 0.15 % to 0.32 %
(10kHz-100kHz)
Current (< 1 method
GHz) (Source)
ELECTRO-
TECHNICAL- Using Multiproduct
AC Voltage @
32 Alternating Calibrator by Direct 1 mV to 330 mV 0.8 % to 0.02 %
(45Hz-10kHz)
Current (< 1 method
GHz) (Source)
ELECTRO-
TECHNICAL- Using Multiproduct
AC Voltage @
33 Alternating Calibrator by Direct 330 mV to 1000 V 0.02 % to 0.04 %
(45Hz-10kHz)
Current (< 1 method
GHz) (Source)
ELECTRO-
TECHNICAL- Using Multiproduct
Capacitance @
34 Alternating Calibrator by Direct 220 pF to 330 nF 5.85 % to 0.45 %
(1kHz)
Current (< 1 method
GHz) (Source)
ELECTRO-
TECHNICAL- Using Multiproduct
Capacitance @
35 Alternating Calibrator by Direct 330 nF to 30 mF 0.45 % to 1.5 %
(1kHz)
Current (< 1 method
GHz) (Source)
ELECTRO-
TECHNICAL- Using Inductance
36 Alternating Inductance @ (1kHz) box by Direct 1 mH to 10 H 3%
Current (< 1 Method
GHz) (Source)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 56 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO- Using 8½ Digital

TECHNICAL- Multimeter &
37 DIRECT DC Current Multifunction 10 µA to 20 mA 0.052 % to 0.003 %
CURRENT Calibrator by Direct/
(Measure) Comparison method
ELECTRO- Using 6½ Digital
TECHNICAL- Multimeter &
38 DIRECT DC Current Multifunction 100 µA to 100 mA 0.1 % to 0.07 %
CURRENT Calibrator by Direct/
(Measure) Comparison method
ELECTRO- Using 6½ Digital
TECHNICAL- Multimeter &
39 DIRECT DC Current Multifunction 100 mA to 10 A 0.07 % to 0.2 %
CURRENT Calibrator by Direct/
(Measure) Comparison method
ELECTRO- Using Shunt with 6½
TECHNICAL- Digital Multimeter &
40 DIRECT DC Current current source by 20 A to 100 A 1.76 %
CURRENT Direct/ Comparison
(Measure) method
ELECTRO- Using 8½ Digital
TECHNICAL- Multimeter &
41 DIRECT DC Current Multifunction 20 mA to 20 A 0.003 % to 0.059 %
CURRENT Calibrator by Direct/
(Measure) Comparison method
ELECTRO-
Using HV Divider
TECHNICAL-
with Indicator & HV
42 DIRECT DC High Voltage 1 kV to 20 kV 1.97 % to 2.10 %
source by Direct/
CURRENT
Comparison method
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 57 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
TECHNICAL-
Using HV Divider by
43 DIRECT DC High Voltage 20 kV to 100 kV 2.30 % to 3.06 %
Direct method
CURRENT
(Measure)
ELECTRO- Using 6½ Digital
TECHNICAL- Multimeter &
44 DIRECT DC Voltage Multifunction 1 mV to 1 V 0.44 % to 0.085 %
CURRENT Calibrator by Direct/
(Measure) Comparison method
ELECTRO- Using 6½ Digital
TECHNICAL- Multimeter &
45 DIRECT DC Voltage Multifunction 1 V to 1000 V 0.085 % to 0.006 %
CURRENT Calibrator by Direct/
(Measure) Comparison method
ELECTRO- Using 8½ Digital
TECHNICAL- Multimeter &
46 DIRECT DC Voltage Multifunction 10 µV to 1000 V 5.80 % to 0.0008 %
CURRENT Calibrator by Direct/
(Measure) Comparison method
ELECTRO-
TECHNICAL- Using 6½ Digital
47 DIRECT Resistance (2 Wire) Multimeter by Direct 100 ohm to 1 Gohm 0.07 % to 2.6 %
CURRENT method
(Measure)
ELECTRO-
TECHNICAL- Using 8½ Digital
48 DIRECT Resistance (2 Wire) Multimeter by Direct 2 Mohm to 20 Mohm 0.01 % to 0.0035 %
CURRENT method
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 58 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
TECHNICAL- Using 8½ Digital
20 Mohm to 20
49 DIRECT Resistance (2 Wire) Multimeter by Direct 0.0035 % to 0.3 %
Gohm
CURRENT method
(Measure)
ELECTRO-
TECHNICAL- Using 6½ Digital
Resistance (2 Wire/
50 DIRECT Multimeter by Direct 1 ohm to 100 ohm 0.15 % to 0.07 %
4 Wire)
CURRENT method
(Measure)
ELECTRO-
TECHNICAL- Using 8½ Digital
Resistance (2 Wire/ 100 µohm to 2
51 DIRECT Multimeter by Direct 0.5 % to 0.0015 %
4 Wire) Mohm
CURRENT method
(Measure)
ELECTRO-
TECHNICAL- Using Multiproduct
52 DIRECT DC Current Calibrator by Direct 10 µA to 330 mA 0.25 % to 0.02 %
CURRENT method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
53 DIRECT DC Current Calibrator by Direct 10 A to 20 A 0.07 % to 0.026 %
CURRENT method
(Source)
ELECTRO-
Using Multiproduct
TECHNICAL-
Calibrator with
54 DIRECT DC Current 20 A to 1000 A 0.52 % to 0.64 %
Current Coil by
CURRENT
Direct method
(Source)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 59 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
TECHNICAL- Using Multiproduct
55 DIRECT DC Current Calibrator by Direct 330 mA to 10 A 0.02 % to 0.07 %
CURRENT method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
56 DIRECT DC Voltage Calibrator by Direct 1 mV to 33 V 0.15 % to 0.002 %
CURRENT method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
57 DIRECT DC Voltage Calibrator by Direct 33 V to 1000 V 0.002 % to 0.003 %
CURRENT method
(Source)
ELECTRO-
TECHNICAL- Using Standard
1 Gohm to 200
58 DIRECT Resistance (2 Wire) Resistance box by 3.55 % to 3.79 %
Gohm
CURRENT Direct method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
59 DIRECT Resistance (2 Wire) Calibrator by Direct 1 Mohm to 10 Mohm 0.004 % to 0.03 %
CURRENT method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
10 Mohm to 330
60 DIRECT Resistance (2 Wire) Calibrator by Direct 0.03 % to 0.35 %
Mohm
CURRENT method
(Source)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 60 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
TECHNICAL- Using Multiproduct
330 Mohm to 1
61 DIRECT Resistance (2 Wire) Calibrator by Direct 0.35 % to 0.2 %
Gohm
CURRENT method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
Resistance (2 Wire/
62 DIRECT Calibrator by Direct 1 µohm to 1 Mohm 0.09 % to 5.77 %
4 Wire)
CURRENT method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
63 ELECTRICAL Conductivity meter Calibrator by 0 to 1000 mS/cm 0.061 % to 2.88 %
EQUIPMENT Simulation method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
Oscilloscopes/
64 ELECTRICAL Calibrator by Direct 1 mV to 130 V 4.9 % to 0.35 %
Amplitude
EQUIPMENT method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
Oscilloscopes/Bandw
65 ELECTRICAL Calibrator by Direct 50 kHz to 1.1 GHz 4.85 %
idth
EQUIPMENT method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
66 ELECTRICAL Oscilloscopes/Time Calibrator by Direct 2 ns to 5 s 0.03 % to 0.6 %
EQUIPMENT method
(Source)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 61 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
TECHNICAL- Using Multiproduct
67 ELECTRICAL pH meter Calibrator by 0 to 14 pH 0.01 pH
EQUIPMENT Simulation method
(Source)
ELECTRO-
TECHNICAL- Power Factor Using Multiproduct
68 ELECTRICAL (Lead/Lag) @ 50 Hz Calibrator by Direct 0.01 PF to 1 PF 0.002 PF
EQUIPMENT /60 Hz method
(Source)
ELECTRO- Using 8½ Digital
TECHNICAL- Multimeter &
B-Type
69 TEMPERATURE Multiproduct 100 °C to 1800 °C 0.6 °C
Thermocouple
SIMULATION Calibrator by Direct/
(Measure) Comparison method
ELECTRO- Using 8½ Digital
TECHNICAL- Multimeter &
E-Type -200 °C
70 TEMPERATURE Multiproduct 0.087 °C
Thermocouple to 1000 °C
SIMULATION Calibrator by Direct/
(Measure) Comparison method
ELECTRO- Using 8½ Digital
TECHNICAL- Multimeter &
K-Type
71 TEMPERATURE Multiproduct -200 °C to 1200 °C 0.085 °C
Thermocouple
SIMULATION Calibrator by Direct/
(Measure) Comparison method
ELECTRO- Using 8½ Digital
TECHNICAL- Multimeter &
N-Type
72 TEMPERATURE Multiproduct -200 °C to 1300 °C 0.13 °C
Thermocouple
SIMULATION Calibrator by Direct/
(Measure) Comparison method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 62 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO- Using 8½ Digital

TECHNICAL- Multimeter &
R-Type
73 TEMPERATURE Multiproduct 0 °C to 1700 °C 0.6 °C
Thermocouple
SIMULATION Calibrator by Direct/
(Measure) Comparison method
ELECTRO-
TECHNICAL- Using 8½ Digital
74 TEMPERATURE RTD Multimeter by Direct -200 °C to 800 °C 0.25 °C
SIMULATION method
(Measure)
ELECTRO- Using 8½ Digital
TECHNICAL- Multimeter &
S-Type
75 TEMPERATURE Multiproduct 0 °C to 1700 °C 0.6 °C
Thermocouple
SIMULATION Calibrator by Direct/
(Measure) Comparison method
ELECTRO- Using 8½ Digital
TECHNICAL- Multimeter &
T-Type
76 TEMPERATURE Multiproduct -200 °C to 400 °C 0.14 °C
Thermocouple
SIMULATION Calibrator by Direct/
(Measure) Comparison method
ELECTRO-
TECHNICAL- Using Multiproduct
B-Type
77 TEMPERATURE Calibrator by Direct 450 °C to 1820 °C 0.8 °C
Thermocouple
SIMULATION method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
E-Type
78 TEMPERATURE Calibrator by Direct -200 °C to 1000 °C 0.15 °C
Thermocouple
SIMULATION method
(Source)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 63 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
TECHNICAL- Using Multiproduct
J-Type
79 TEMPERATURE Calibrator by Direct -200 °C to 1000 °C 0.6 °C
Thermocouple
SIMULATION method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
K-Type
80 TEMPERATURE Calibrator by Direct -200 °C to 1200 °C 0.6 °C
Thermocouple
SIMULATION method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
N-Type
81 TEMPERATURE Calibrator by Direct -200 °C to 1300 °C 0.6 °C
Thermocouple
SIMULATION method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
R-Type
82 TEMPERATURE Calibrator by Direct 100 °C to 1700 °C 0.65 °C
Thermocouple
SIMULATION method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
83 TEMPERATURE RTD Calibrator by Direct -200 °C to 800 °C 0.25 °C
SIMULATION method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
S-Type
84 TEMPERATURE Calibrator by Direct 100 °C to 1700 °C 0.65 °C
Thermocouple
SIMULATION method
(Source)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 64 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
TECHNICAL- Using Multiproduct
T-Type
85 TEMPERATURE Calibrator by Direct -200 °C to 400 °C 0.21 °C
Thermocouple
SIMULATION method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
86 TIME & Frequency Calibrator by Direct 1 MHz to 10 MHz 0.016 % to 0.06 %
FREQUENCY method
(Measure)
ELECTRO- Using 8½ Digital
TECHNICAL- Multimeter &
87 TIME & Frequency Multiproduct 10 Hz to 1 MHz 0.06 % to 0.006 %
FREQUENCY Calibrator by Direct/
(Measure) Comparison method
ELECTRO- Using 6½ Digital
TECHNICAL- Multimeter &
88 TIME & Frequency Multiproduct 10 Hz to 1000 kHz 0.068 %
FREQUENCY Calibrator by Direct/
(Measure) Comparison method
ELECTRO-
TECHNICAL- Using Time Totalizer
89 TIME & Time by Comparison 2 s to 30 min 0.37 s to 1 s
FREQUENCY method
(Measure)
ELECTRO-
TECHNICAL- Using Time Totalizer
90 TIME & Time by Comparison 30 min to 24 hr 1 s to 104.77 s
FREQUENCY method
(Measure)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 65 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

ELECTRO-
TECHNICAL- Using Multiproduct
91 TIME & Frequency Calibrator by Direct 1 MHz to 10 MHz 0.08 % to 0.15 %
FREQUENCY method
(Source)
ELECTRO-
TECHNICAL- Using Multiproduct
92 TIME & Frequency Calibrator by Direct 10 Hz to 1 MHz 0.058 % to 0.08 %
FREQUENCY method
(Source)
Using Tachometer
MECHANICAL- Speed –RPM (source RPM
>1000 rpm to 4000
93 ACCELERATION Tachometer generator/Calibrator 10 rpm
rpm
AND SPEED (Contact) ) by Comparison
method
Using Tachometer
MECHANICAL- Speed –RPM (source RPM
94 ACCELERATION Tachometer generator/Calibrator 10 rpm to 100 rpm 0.52 rpm
AND SPEED (Contact) ) by Comparison
method
Using Tachometer
MECHANICAL- Speed –RPM (source RPM
100 rpm to 1000
95 ACCELERATION Tachometer generator/Calibrator 3.5 rpm
rpm
AND SPEED (Contact) ) by Comparison
method
Using Tachometer
MECHANICAL- Speed –RPM (source RPM
>4000 rpm to 90000
96 ACCELERATION Tachometer (Non- generator/Calibrator 27.49 rpm
rpm
AND SPEED Contact) ) by Comparison
method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 66 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Using Vibration
MECHANICAL- Vibration meter meter calibrator by
97 ACCELERATION Acceleration meter Comparison method 1 m/s² @ 636.6 Hz 0.078 m/s²
AND SPEED @ 636.6 Hz as per ISO :
16063-21
Using Vibration
MECHANICAL- Vibration meter/ meter calibrator by
98 ACCELERATION Acceleration meter Comparison method 1 m/s² @ 15.92 Hz 0.074 m/s²
AND SPEED @ 15.92 Hz as per ISO :
16063-21
MECHANICAL-
DIMENSION Using Extensometer
(BASIC Extensometer - Calibrator by
99 Up to 5 mm 5 µm
MEASURING Traverse Comparison Method
INSTRUMENT, as per ASTM E-83
GAUGE ETC.)
MECHANICAL- Using Extensometer
DIMENSION Calibrator by
(BASIC Extensometer - Comparison Method
100 Up to 5 mm 5 µm
MEASURING Traverse as per IS : 12872 :
INSTRUMENT, 2021,ISO 9513 :
GAUGE ETC.) 2012
MECHANICAL-
DIMENSION
Surface Plates (Cast Using Digital level 2.5xSQRT(L+W/125)
(BASIC 4000 mm x 4000
101 Iron/Granite)- by comparison µm where L and W
MEASURING mm
Flatness method in mm
INSTRUMENT,
GAUGE ETC.)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 67 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

MECHANICAL-
DIMENSION Using Surface Plate,
(BASIC V-Block- Test Mandrels &
102 Up to 200 mm 13 µm
MEASURING Symmetricity probe with DRO by
INSTRUMENT, Comparison method
GAUGE ETC.)
MECHANICAL-
DIMENSION Using Surface Plate,
(BASIC Test Mandrels &
103 V-Block-Parallelism Up to 200 mm 13 µm
MEASURING probe with DRO by
INSTRUMENT, Comparison method
GAUGE ETC.)
MECHANICAL-
DIMENSION Using Square
(BASIC cylinder, Slip gauge
104 V-Block-Squareness Up to 200 mm 13 µm
MEASURING by Comparison
INSTRUMENT, method
GAUGE ETC.)
MECHANICAL-
2D Height Gauge Using Long Slip
DIMENSION
105 (Vernier/Dial/Digital) Gauge by 0 to 1000 mm 10 µm
(PRECISION
L.C.-0.1 µm (Linear) Comparison method
INSTRUMENTS)
MECHANICAL- 2D Height Gauge
Using Master square
DIMENSION (Vernier/Dial/Digital)
106 cylinder by 0 to 1000 mm 5.20 µm
(PRECISION L.C.-0.1 µm
comapsrison method
INSTRUMENTS) (Squareness)
MECHANICAL-
Profile projector Using Angular
DIMENSION
107 L.C-1 sec Angular graticule scale by 0° to 360° 1.2 minute
(PRECISION
measurement Comparison method
INSTRUMENTS)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 68 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

MECHANICAL-
Profile projector
DIMENSION Using Glass Scale by
108 L.C.-0.001 mm 0 to 300 mm 5 µm
(PRECISION Comparison method
Linear measurement
INSTRUMENTS)
MECHANICAL-
DIMENSION Profile projector Using Glass Scale by
109 10 X to 100 X 1%
(PRECISION Magnification Comparison method
INSTRUMENTS)
MECHANICAL- Using Surface
DIMENSION Surface Roughness Roughness Master
110 0.1 µm to 3 µm 10 %
(PRECISION Tester (Ra) by Comparison
INSTRUMENTS) method
MECHANICAL-
Video Measuring Using Glass graticule
DIMENSION
111 Machine ( Angular ) by comparison 0 ° to 360 ° 15 s
(PRECISION
L.C.: 1 arc second Method
INSTRUMENTS)
MECHANICAL- Video Measuring
DIMENSION Machine/Microscope Using Glass scale by
112 0 to 200 mm 3 µm
(PRECISION ( Linear ) L.C.: comparison Method
INSTRUMENTS) 0.0001 mm
Using Load Cell with
MECHANICAL-
Indicator as per IS
HARDNESS Test Force of Brinell
113 1500 - (Part - 2) : 153.2 N to 29421 N 0.5 %
TESTING Hardness Tester
2021, ISO 6506 -
MACHINES
(Part - 2) : 2017
Using Load Cell with
MECHANICAL-
Test Force of Indicator as per IS
HARDNESS
114 Rockwell Hardness 1586 - (Part - 2) : 29.42 N to 1471 N 0.5 %
TESTING
Tester 2018, ISO 6508 -
MACHINES
(Part-2) : 2015

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 69 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Using Load Cell with

MECHANICAL-
Indicator as per IS
HARDNESS Test Force of Vickers
115 1501 - (Part - 2) : 49.03 N to 294.2 N 0.5 %
TESTING Hardness Tester
2020, ISO 6507 -
MACHINES
(Part - 2) : 2018
Using Standard
MECHANICAL-
Hardness Test
HARDNESS Verification of Brinell
116 Blocks by Indirect HBW 10/3000 1.6 %
TESTING Hardness Tester
Method as per ASTM
MACHINES
E 10
Using Standard
Hardness Test
MECHANICAL-
Blocks by Indirect
HARDNESS Verification of Brinell
117 Method as per IS HBW 10/3000 1.6 %
TESTING Hardness Tester
1500 (Part-2) : 2021,
MACHINES
ISO 6506 (Part-2) :
2017
Using Standard
MECHANICAL-
Hardness Test
HARDNESS Verification of Brinell
118 Blocks by Indirect HBW 2.5/187.5 1.6 %
TESTING Hardness Tester
Method as per ASTM
MACHINES
E 10
Using Standard
Hardness Test
MECHANICAL-
Blocks by Indirect
HARDNESS Verification of Brinell
119 Method as per IS HBW 2.5/187.5 1.6 %
TESTING Hardness Tester
1500 (Part - 2) :
MACHINES
2021, ISO 6506 (Part
- 2) : 2017

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 70 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Using Standard
MECHANICAL-
Hardness Test
HARDNESS Verification of Brinell
120 Blocks by Indirect HBW 5/750 1.9 %
TESTING Hardness Tester
Method as per ASTM
MACHINES
E 10
Using Standard
Hardness Test
MECHANICAL-
Blocks by Indirect
HARDNESS Verification of Brinell
121 Method as per IS HBW 5/750 1.9 %
TESTING Hardness Tester
1500 (Part - 2) :
MACHINES
2021, ISO 6506 (Part
- 2) : 2017
Using Standard
MECHANICAL-
Verification of Hardness Test
HARDNESS
122 Rockwell Hardness blocks by Indirect HRA 1 HRA
TESTING
Tester Method as per ASTM
MACHINES
E - 18
Using Standard
Hardness Test
MECHANICAL-
Verification of blocks by Indirect
HARDNESS
123 Rockwell Hardness Method as per IS HRA 1 HRA
TESTING
Tester 1586 (Part-2) : 2018,
MACHINES
ISO 6508 - (Part-2) :
2015
Using Standard
Hardness Test block
MECHANICAL-
Verification of by Indirect Method
HARDNESS
124 Rockwell Hardness as per IS 1586 HRBW 1 HRBW
TESTING
Tester (Part-2) : 2018 & ISO
MACHINES
6508 - (Part-2) :
2015

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 71 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Using Standard
MECHANICAL-
Verification of Hardness Test
HARDNESS
125 Rockwell Hardness blocks by Indirect HRBW 1 HRBW
TESTING
Tester Method as per ASTM
MACHINES
E - 18
Using Standard
Hardness Test block
MECHANICAL-
Verification of by Indirect Method
HARDNESS
126 Rockwell Hardness as per IS 1586 HRC 1 HRC
TESTING
Tester (Part-2) : 2018 & ISO
MACHINES
6508 - (Part-2) :
2015
Using Standard
MECHANICAL-
Verification of Hardness Test
HARDNESS
127 Rockwell Hardness blocks by Indirect HRC 1 HRC
TESTING
Tester Method as per ASTM
MACHINES
E - 18
Using Standard
MECHANICAL-
Verification of Hardness Test
HARDNESS
128 Vickers Hardness Blocks by Indirect HV 10 1.5 %
TESTING
Testing Machine Method as per ASTM
MACHINES
E 92
Using Standard
Hardness Test
MECHANICAL-
Verification of Blocks by Indirect
HARDNESS
129 Vickers Hardness Method as per IS HV 10 1.5 %
TESTING
Testing Machine 1501(Part-2) : 2020,
MACHINES
ISO 6507 (Part-2) :
2018

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 72 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Using Standard
MECHANICAL-
Verification of Hardness Test
HARDNESS
130 Vickers Hardness Blocks by Indirect HV 30 1.5 %
TESTING
Testing Machine Method as per ASTM
MACHINES
E 92
Using Standard
Hardness Test
MECHANICAL-
Verification of Blocks by Indirect
HARDNESS
131 Vickers Hardness Method as per IS HV 30 1.5 %
TESTING
Testing Machine 1501 (Part-2) : 2020,
MACHINES
ISO 6507 (Part-2) :
2018
Hydraulic Pressure Using Digital
Dial and Digital pressure Calibrator ,
MECHANICAL- Pressure Gauges, 6½ Digital
PRESSURE Pressure Multimeter,
132 >400 bar to 700 bar 0.56 bar
INDICATING Transmitters, Hydraulic pressure
DEVICES Transducers, pump as per DKD-R
Pressure Switches 6-1 by Comparison
(Medium:Hydraulic) method
Hydraulic Pressure Using Digital
Dial and Digital pressure Calibrator,
MECHANICAL- Pressure Gauges, 6½ Digital
PRESSURE Pressure Multimeter,
133 30 bar to 400 bar 0.15 bar
INDICATING Transmitters, Hydraulic pressure
DEVICES Transducers, pump as per DKD-R
Pressure Switches 6-1 by Comparison
(Medium:Hydraulic) method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 73 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Pneumatic Pressure
Using Digital
Dial and Digital
pressure Calibrator,
Pressure Gauges,
MECHANICAL- 6½ Digital
Magnehelic gauges,
PRESSURE Multimeter, >20 mbar to 200
134 Pressure 0.13 mbar
INDICATING Pneumatic pressure mbar
Transmitter,
DEVICES pump as per DKD-R
Transducers,
6-1 by Comparison
Pressure Switch
method
(Medium:Pneumatic)
Pneumatic Pressure
Using Digital
Dial and Digital
pressure Calibrator,
Pressure Gauges,
MECHANICAL- 6½ Digital
Pressure
PRESSURE Multimeter
135 Transmitters, >0.2 bar to 1 bar 0.00086 bar
INDICATING ,Pneumatic pressure
Transducers,
DEVICES pump as per DKD-R
Pressure Switches
6-1 by Comparison
(Medium:
method
Pneumatic)
Pneumatic Pressure
Using Digital
Digital and Dial
pressure
Pressure Gauges,
Calibrator/gauge,
MECHANICAL- Magnehelic gauges,
6½ Digital
PRESSURE Pressure
136 Multimeter & 0 to 20 mbar 0.01 mbar
INDICATING Transducers,
Pneumatic pressure
DEVICES Transmitters,
pump as per DKD-R
Pressure Switch
6-1 by Comparison
(Medium:
method
Pneumatic)

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 74 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Pneumatic Vacuum Using Digital

Dial and Digital Vacuum Calibrator ,
MECHANICAL- Vacuum Gauges, 6½ Digital
PRESSURE Vacuum Multimeter,
137 -0.93 bar to 0 0.00064 bar
INDICATING Transmitters,Transd Pneumatic pressure
DEVICES ucers, Vacuum pump as per DKD-R
Switches 6-1 by Comparison
(Medium:Pneumatic) method
Using Digital
Pressure Dial and
pressure Calibrator,
Digital Pressure
MECHANICAL- 6½ Digital
Gauges, Pressure
PRESSURE Multimeter,
138 Transmitters, >1 bar to 30 bar 0.143 bar
INDICATING Pneumatic pressure
Transducers
DEVICES pump as per DKD-R
,Pressure Switches
6-1 by Comparison
(Medium:Pneumatic)
method
MECHANICAL- Torque Tools - Using Torque Sensor
TORQUE Pneumatic, with indicator as per
139 1 Nm to 10 Nm 0.44 %
GENERATING Electrical, Hydraulic IS 15411 : 2003 /
DEVICES and Oil Pulse Tools ISO 5393 :1994
MECHANICAL- Torque Tools - Using Torque Sensor
TORQUE Pneumatic, with Indicator as per
140 10 Nm to 50 Nm 0.8 %
GENERATING Electrical, Hydraulic IS 15411 : 2003 /
DEVICES and Oil Pulse Tools ISO 5393 : 1994
MECHANICAL- Using Load Cells
UTM, TENSION Verification of UTM, with Indicator by
CREEP AND CTM, Spring Testing Comparison Method
141 Up to 1000 kN 0.4 %
TORSION Machine - as per IS 1828 (Part
TESTING Compression Mode - 1) : 2022, ISO 7500
MACHINE (Part - 1) : 2018

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 75 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

MECHANICAL- Electronic weighing Using standard

WEIGHING balance (Class I & weights E1 class
142 0 to 82 g 0.03 mg
SCALE AND Coarser) Readability weights as per OIML
BALANCE :0.01 mg R-76-1
MECHANICAL- Electronic weighing Using standard
WEIGHING balance (Class I & weights E1 class
143 0 to 220 g 0.22 mg
SCALE AND Coarser) Readability weights as per OIML
BALANCE :0.1 mg R-76-1
MECHANICAL- Electronic weighing
Using standard F1
WEIGHING balance (Class II &
144 class weights as per 0 to 2.2 kg 30 mg
SCALE AND Coarser )
OIML R-76-1
BALANCE Readability:10 mg
MECHANICAL- Electronic weighing
Using standard F1
WEIGHING balance (Class II &
145 class weights as per 0 to 32.2 kg 250 mg
SCALE AND Coarser) Readability
OIML R-76-1
BALANCE :100 mg
MECHANICAL- Electronic weighing
Using standard E2 &
WEIGHING balance (Class II &
146 F1 class weights as 0 to 1.02 kg 3.0 mg
SCALE AND Coarser)
per OIML R-76-1
BALANCE Readability:1 mg
MECHANICAL- Electronic weighing
Using standard F1
WEIGHING balance (Class III &
147 class weights as per 0 to 200 kg 58 g
SCALE AND Coarser) Readability
OIML R-76-1
BALANCE :10 g

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 76 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Humidity &
Temperature Sensor
Using Temperature
with Indicator of
& Humidity meter,
THERMAL- Transducer/Transmit
source Humidity 20 %rh to 95 %rh
148 SPECIFIC HEAT ter with 2 %rh
Generator/Calibrator @20°C to 35°C
& HUMIDITY Indicator/Digital
with probe by
thermo
Comparison method
hygrometer/Data
logger
Humidity&
Temperature
Using Temperature
indicator with sensor
& Humidity meter
THERMAL- of environmental,
(source Humidity 20 %rh to 95 %rh
149 SPECIFIC HEAT Climatic, Humidity 2 %rh
Generator/Calibrator @20°C to 50°C
& HUMIDITY Chamber/calibrator
) with probe by
(Relative Humidity
Comparison method
at a specified Single
Position )
Humidity&
Temperature Sensor Using RTD & 6½
with indicator of Digital Multimeter,
THERMAL- Transducer/Transmit source Humidity/
5 °C to 50 °C @50%
150 SPECIFIC HEAT ter with Temperature 0.30 °C
rh
& HUMIDITY Indicator/Digital Generator/Calibrator
thermo by Comparison
hygrometer/Data method
logger

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 77 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Humidity&
Temperature Sensor
Using Temperature
with Indicator of
& Humidity meter
THERMAL- Transducer/Transmit
(source Humidity 20 %rh to 50 %rh
151 SPECIFIC HEAT ter with 2 %rh
Generator/Calibrator @35°C to 50°C
& HUMIDITY Indicator/Digital
) with probe by
thermo
Comparison method
hygrometer/Data
logger
Using R-Type
THERMAL- Thermocouple, DAQ
152 Dry Block Calibrators 600 °C to 1200 °C 1.30 °C
TEMPERATURE Temp scanner as per
EURAMET cg -13
Using PT-100 Sensor
Freezer, cold & Thermocouple
THERMAL- chamber, Oven, (minimum 9 sensor)
153 -40 °C to 400 °C 2.60 °C
TEMPERATURE Furnace, Coating & Data logger by
oven multiposition
method
Using RTD (Pt-100),
6½ Digital
Indicator with sensor
Multimeter /
THERMAL- of Liquid Baths/ Dry
154 Temperature 140 °C to 600 °C 0.4 °C
TEMPERATURE Block Calibrators
indicator/Calibrator
(Single Position)
by Comparison
method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 78 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Using RTD (Pt-100),

6½ Digital
Indicator with sensor
Multimeter /
THERMAL- of Liquid Baths/ Dry
155 Temperature -35 °C to 140 °C 0.1 °C
TEMPERATURE Block Calibrators
indicator/Calibrator
(Single Position)
by Comparison
method
Using Master Non
IR /Non Contact contact
THERMAL- Digital thermometer, Black
156 0 °C to 100 °C 2.75 °C
TEMPERATURE Thermometer/Gun/ body source
Pyrometer (emissivity 0.95)by
Comparison method
Using Master Non
IR /Non Contact contact
THERMAL- Digital thermometer, Black
157 100 °C to 500 °C 2.89 °C
TEMPERATURE Thermometer/Gun/ body source
Pyrometer (emissivity 0.95)by
Comparison method
Using RTD (Pt-100),
Liquid in Glass 6½ Digital
THERMAL-
158 thermometer / Dial Multimeter & Liquid 140 °C to 250 °C 0.68 °C
TEMPERATURE
thermometer bath by Comparison
method
Using RTD (Pt-100),
Liquid in Glass 6½ Digital
THERMAL-
159 thermometer / Dial Multimeter & Liquid -35 °C to 140 °C 0.2 °C
TEMPERATURE
thermometer bath by Comparison
method

This is annexure to 'Certificate of Accreditation' and does not require any signature.
 UNIVERSAL CALIBRATION SERVICES PVT. LIMITED, PLOT NO-G-43/1&2, G-44/1&2,
Laboratory Name :
G-BLOCK, AJANTA NAGAR, MIDC, CHINCHWAD, PUNE, MAHARASHTRA, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number CC-2412 Page No 79 of 79
Validity 10/09/2022 to 09/09/2024 Last Amended on 13/03/2024

Measurand or Reference
Measurement range and
Material/Type of instrument * Calibration and
Calibration or Measurement additional parameters
S.No Discipline / Group or material to be calibrated Measurement
Method or procedure where applicable(Range
or measured / Quantity Capability(CMC)(±)
and Frequency)
Measured /Instrument

Using Thermocouple
THERMAL- Oven, Furnace, (minimum 9 sensor)
160 400 °C to 1200 °C 3.80 °C
TEMPERATURE Coating oven & Data logger by
Multiposition ethod
RTD/Thermocouple / Using RTD (Pt-100),
Sensor with or 6½ Digital
THERMAL-
161 without temperature Multimeter & /Dry -35 °C to 140 °C 0.05 °C
TEMPERATURE
Indicator/ Data bath by Comparison
logger / Recorder method
RTD/Thermocouple / Using RTD (Pt-100),
Sensor with or 6½ Digital
THERMAL-
162 without temperature Multimeter, Dry 140 °C to 600 °C 0.30 °C
TEMPERATURE
Indicator/ Data block by Comparison
logger / Recorder method
Temperature
Indicator with sensor Using RTD (Pt-100)
THERMAL- of Freezer, cold & 6½ Digital
163 -65 ºC to 600 ºC 1.60 ºC
TEMPERATURE chamber, Oven, Multimeter by
Furnace (Single Comparison method
Position)
Using R-Type
Thermocouple/
Thermocouple, 6½
sensor with or
Digital Multimeter,
THERMAL- without,
164 Temperature 600 °C to 1200 °C 1.28 °C
TEMPERATURE temperature
indicator/ calibrator
Indicator/ Data
& Dry block by
logger/ Recorder
Comparison method
* CMCs represent expanded uncertainties expressed at approximately the 95% level of confidence, using a coverage factor of k = 2.

This is annexure to 'Certificate of Accreditation' and does not require any signature.