INSTRUCTION MANUAL

FOR
16 TO 1 MULTIPLEXER & 1 TO 16 DEMULTIPLEXER

MODEL NO.

16 to 1 Line Multiplexer & 1 to 16 Line Demultiplexer has been designed to study the different type
of a Multplexer & Demultiplexer

Iypes of Multiplexer
2:1 Multiplexer.

() 4:1 Multiplexer

() 8:1 Multiplexer.
16:1 Multiplexer

ypes of Demultlplexer
0 1:2Demultiplexer.
() 1:4 Demultiplexer

(1) 1:8 Demultiplexer.

(M) 1:16 Demultiplexer.

The instrument comprises of the following bullt In parts :

Fixed output DC Regulated Power Supply of 5Volts.

2 Twenty Two SPDT swltches are provlded on tho tront panel to select Logke '0"' & Logie'l' inputs

Seventeen Output Indlocatora (LED's) are provlded on the front panel to observe the output status

IC's 74160& 74164 are mounted on the tront panel and lImportant oonnections ave brvught out en
80ckets

The front panel ofthe Inetrument lo Printed Cireult all the dlayrmme are printet
on the front panel.
 THEORY

ForMultiplexer
Muitiplexer means many into one i,e muitipiexer s a ogic crcut which nas many inprs ut singe
output Amutiplexer accepts several data inputs but alow only one ofthem &a tme ge rrough to e ops
The pinout diagram of a Multiplexer is shown Fig. (1). The output of this is the vetsd oupt This s a 24 pin
DIP. The selet ines are $3, s2, $1 &S0. An input line D0-D15 are seiectes correspondingtoTe secma
number representative $3, $2, S1& S0. To performderenttype ofmutiplexer experimert we tave sec
74150. Ithas 16 data ine inputs (DO to D15) and only one outputs Y. S, iste strobe inpa(actve iow). S3, S2.
s1 and So are select ines. These ines selet one out of sixteen inputs at cutput. For eg # we wil spoy 00
at $3, $2 S1 &S0 frst data input DO will be selected

MULTIPLEXER USING IC 74150

FFETETITFFFFT LOGIC NEUTS

FIG (1)

For Demultiplexer
Demutplexer means one into many ie Demuttoiexer is a ogic circut wicn es singe r o s ii

many output it accepts a single input & distributes t over several outputs. The seiea input code deemines

to which output the data input w be transmited. A 1 to 16 ine Demuipiexer has one data nput ior seec
ines (S0. S1, $2 & $3) and 16 outputs. The pin out diagram of a Demuliplexer is shown Fig 2). To periom

have used C 74154. khes 4 e

diferent type of Demutiplexerl four Ene to 16 ine decoder experiment, we
select ine inputs (S0 to s3) and two strobe inputs G1 à G2 Out of these two stobe jnputs G1 s usedas cee

input&G2 s connected to kogic 0 level

Note: Demultiplexer can be used as decoder by connecting data input (G1, G2) to logic 0.
- - - OUTPUT NDICATORS-

LLLL1LLL1.LLL
DEMULTIPLEXER USING IC 74154

FIG (2)

2
 PROCEDURE
MULTIPLEXER

A For 2:1 Multiplexer

For this case connect Select
input S1, $2, $3, ST to zero and sO to logical Input (0,1)
using patchchords.

2 Connect the Logic inputs to all the data inputs (DO to D15)
through patchchords.

Keep data input D2 to D15 at logic 0.

4. Connect the Y output to output indicator

through patchchord.
Switch ON the instrument using ON/OFF toggle switch provided on the front panel.

OBSERVATION TABLE No.(1)

Verify the Observation Table No. (1) INPUTS OUTPUT
for different set of
inputs. The output S.no Strobe Select Inputs
of IC 74150 is inverted $3 $2 S1 SO
output, so a
NOT Gate is used to get non-inverted
2
output. Connect the Youtput to input
of NOT Gate.

B. For 4:1 Multiplexer

For this case connect select input $2, $3, ST to zero and S0, S1 to logical Input (0,1).

2 Connect the Logic inputs to all the data inputs (DO to D15) through patchchords.

3. Keep data input D4 to D15 at logic 0.

4. Connect the Y output to output indicator through patchchord.

5. Switch ON the instrument using ON/OFF toggle switch provided on the front panel.

OBSERVATION TABLE No.(2)

6. Verify the Observation Table No. (2)- INPUTS OUTPUT
for different set of inputs. The output S.no Strobe Select Inputs
S, $3 $2 $1 SO
of IC 74150 is inverted output, so a
0 DO
NOT Gate is used to get non-inverted 2 1 D1
output. Connect the Y output to input D2
of NOT Gate. D3
C. For 8:1 Multiplexer
For this case connect select
input $3 & ST to zero and S0, S1, $2 to logical Input (0,1).

2. Connect the Logic inputs to ail the data inputs (D0 to D15) through patchchords.

3. Keep data input D8 to D15 at logic 0.

4. Connect the Y output to output indicator

through patchchord.
OBSERVATION TABLE No.(3)
5 Switch ON the instrument using ON/ INPUTS OUTPUT
OFF toggle switch provided on the S.no Strobe Select Inputs
$3 s2 $1 SO Y
front panel
0 DO
2
D
6. Verity the Observation Table No. (3) 3
D2
for different set of inputs. The output 1 D3

of IC 74150 is inverted output, so a 5

D4
D5
NOT Gate is used to get non-inverted
output Connect the Y output to input
7 D6
8 D7
of NOT Gate.

D. For 16:1 Multiplexer

1. Connect the Logic inputs to all the OBSERVATION TABLE No. (4)
data inputs (DO to D15) through INPUTS OUTPUT
patchchords. Also connect logic S.no Strobe Select Inputs_
S1 S0
inputs to S0-$3 & ST. S $3 $2
Do
2 0 D1

2 Connect the Y output to output 1 0

indicator through patchchord.

5 0 D4
0
3. Switch ON the instrument using ON/
OFF toggle switch provided on the 8 1 1
D
D7
front panel.
0 1 D9
11 0 D10
4. Verify the Observation Table No. (4)
12 D11
for different set of inputs. The output
13 D12
of IC 74150 is inverted output, so a 14 0 D13
NOT Gate is used to get non-inverted 15
D14
output. Connect the Youtput to input 16 D15
of NOT Gate.
 '

DEMULTIPLEXER:

A. For 1:2 Demultiplexer

1 For this case connect select

input S1, $2, $3 to zero and SO to logical Input (0,1) using patchchords.

Also connect logic inputs to G1 & G2.

3 Connect the Y0 to Y1 outputs to output indicators through patchchord.

A. Switch ON the instrument using ON/OFF toggle switch provided on the front panel.

5. Apply logic input '0' at Strobe input G2 &G1.

OBSERVATION TABLE No.(5)
6. Verify the Observation Table INPUTS OUTPUT
No. (5) by applying data input S.no Strobe Select Inputs
G2 $3 $2 S1 SO Y
on S0(1 or'0").
YO
Y1
B. For 1:4 Demultiplexer
. For this case connect select input $2, s3 to zero and S0, S1 to logical Input (0,1) using Patchchords.

Also connect logic inputs to G1 & G2.

3. Connect the YO to Y3 outputs to output indicators through patchchor.

Switch ON the instrument using ON/OFF toggle switch provided on the front panel.

OBSERVATION TABLE No. (6)

Apply logic input'0' at Strobe INPUTS OUTPUT
input G2 & G1. S.no Strobe Select Inputs
G2 $3 $2 $1 So Y
0 YO
Verify the Observation Table
Y1
No. (6) by applying data input
Y2
on S0, S1 (1 or '0'). Y3

C. For 1:8 Demultiplexer

1. For this case connect Select input $3to zero and S0,
S1, $2 to logical Input (0,1) using Patchchords.

2 Also connect logic inputs to G1& G2.

3. Connect the Y0 to Y7 outputs to

output indicators through patchchord.
4 Switch ON the instrument OBSERVATION TABLE No. (7)
using ON/OFF toggle switch INPUTS OUTPUT
provided on the front panel. S.no Strobe Select Inputs
G2 $3 S2 $1 SO Y
0 0 0 YO
5 Apply logic input '0' at Strobe 1 Y1
input G2 & G1. 0 2
Y3
Y4
. Verify the Observation Table
6 1 Y5
No. (7) by applying data input 7 0 Y6
on S0, S1, $2 (1'or'0). Y7

D. For 1:16 Demultiplexer

1. Connect the logic Inputs to all the select lines (S0 to S3) through patchchords. Also connect logic

Inputs to G1& G2.

OBSERVATION TABLE No.(8)
INPUTS OUTPUT
2. Connect the Y0 to Y15 S.noStrobe Select Inputs Depend on G1
G2 $3 $2 S1 SO
outputs to output indicators
0 YO
through patchchord. Y1
Y2
Switch ON the instrument 4 1 Y3
using ON/OFF toggle Y4
switch provided on the front 6 0 1 1 Y5
1 1 Y6
panel.
Y7
Y8
Apply logic input '0' at 10 Y9
Strobe input G2 & G1. 11 0 Y10
12 1 Y11
13 Y12
. Verify the Observation Table
14 Y13
No. (8) by applying data
15 0 Y14
input on all select lines (1' 16 Y15
or'0').

STANDARD ACCESSORIES
1. Single Point (4mm) Patchchords for Interconnection. 6 Nos.

2 Instruction Manual (DOC 720). 1 No.

E:ABSOLUTEI 03441 720 16:1 LINE MULTIPLEXER & 1:16 LINE DEMULTIPLEXER