GE Gas Turbine GE10B1 GE10 Heavy Duty Single shaft Gas Turbine GE Gas Turbine GE10B1 Technical

data Secondhand refurbished (zero hours) PGT10, Nuovo Pignone GE10 used gas turbine power
generation package. For sale in Italy. General Electric turbine Turbine a gas ricondizionata (di seconda
mano a zero ore) per la generazione di energia, gruppo turbine generatore, ricondizionato, package
General Elettric GE10 GE10-1 GE10B1 GE Gas Turbine GE10B1 1

2 GE10 Gas Turbines The GE10 is a 12 MW range heavy-duty gas turbine available in both single shaft
and two shaft versions. It is the evolution of the field-proven PGT10A and incorporates the latest in
aerodynamic design in a compact and versatile package arrangement. The design of the GE10 has been
highly refined based on the extensive experience gained operating in all types of environments. There are
over one hundred units running under conditions ranging from the cold of Alaska and Siberia to the heat of
the desert and the humidity of the tropics. Its efficiency and operational flexibility make the GE10 a cost-
effective choice for all applications. The gas generator consists of an 11 stage, high efficiency, axial-flow
compressor and a single combustion chamber capable of burning a great variety of fuels. Maximum
commonality has been maintained between the single and twin shaft models. Both units use the same gas
generator. The two shaft engine is obtained by simply removing the third stage turbine from the single shaft
unit and adding a two-stage low pressure power turbine. This feature is particularly beneficial in reducing
operating and maintenance costs in installations where mixed operation is required. GE10-1 Gas Turbine
2

3 COMPRESSOR The compressor is a high performance eleven stage axial flow design with a 15.5:1
pressure ratio operating under transonic flow conditions, derived from GE s Aircraft Engine aeroderivative
technology. The first three rows of stator blades are variable to optimize cycle efficiency over a wide range
of loads. The gas generator is joined to the base plate at the load flange location. This configuration avoids
load flange movement during all operating conditions (start-up, warm-up, full speed/full load) and during
thermal transients. TURBINE The power turbine is available in two configurations: a single shaft version
primarily for power generation; and a two shaft version for mechanical drive applications. Generator Drive
Single Shaft Version The GE10-1 is a single shaft heavy duty gas turbine designed primarily for generator
drive applications. The turbine section is composed of three reaction stages. The first two stages use the
proven design of the previous PGT10 HP turbine model with cooling provided by air bled from the axial
compressor. The second and third stages have interlocked shrouds to limit tip leakage and blade vibration.
At partial load, inlet variable guide vanes permit optimization of performance with no appreciable change
from simple cycle full load efficiency. The GE10 is a compact turbo-generator optimized for simple cycle,
combined cycle and cogeneration plants (e.g., power shaft on cold side; axial discharge of hot gases) and
suitable for utilization even where space is limited. COMBUSTOR The combustion system consists of a
single, slot-cooled combustion chamber assembly that permits quick and easy maintenance of the hot gas
path. This combustion chamber is able to burn a wide range of fuels including liquid distillates, residuals
and all gaseous fuels including low BTU gas with system modifications. The GE10 combustion system is
available in both conventional and DLE (dry low emissions) configurations. The DLE system is a simple,
field-proven design that guarantees operation at 25 ppmv NOx (burning Natural Gas). The GE10 can also
utilize steam and water injection for NOx reduction and power augmentation. Further reduction of emission
levels is a constant objective of our continuing combustion development and test programs. 3

4 AUXILIARIES The integrated lubrication system (including oil tank) that feeds the gas turbine, the speed
reduction gear and the electric VFD starting motor is located on the turbine base plate. The main lube oil
pump is mechanically driven by the gearbox. An AC electric motor-driven pump guarantees lubrication
during normal operation while a DC electric motor-driven pump is provided for emergency backup. In the
standardized package configuration the oil is cooled by an air cooler. A water cooler can be provided upon
customer request. The thrust and journal bearings are of the tilting pad type. The starting system consists
of a VFD motor drive for the single shaft version. The GE10 control system has been implemented to assure
a high degree of integration and standardization between the engine and the turbine generator package.
Programmable modules guarantee easy implementation of any control and protection scheme to tailor the
control system to the application and customer needs. PACKAGE The package designed for power
generation applications is optimized to minimize plant dimensions and to reduce maintenance cost and
time. In the standard configuration, the speed reduction gear is mounted on the gas turbine base plate. The
auxiliaries are installed on a separate base plate permanently joined to that of the gas turbine base plate
to form a single lift on which the sound-insulated enclosure is mounted. The electric generator is installed
on a concrete foundation to limit the shipping dimensions. The overall length of the generator set is about
13 m. The other modules completing the system are the oil/air exchangers, the air intake filter chamber,
the suction duct (vertical suction) and the exhaust system (axial exhaust). The enclosure has a sound
pressure level lower than 85 dba at 1 m. This acoustic design meets ISO NR 50 limits at 100 m. 4

5 Gas turbine Data Construction Features Gas Turbine Model Series Gas Turbine type Cycle Number of
Shafts Direction of Rotation Facing downstream from inlet Casing Gas Turbine Nameplate Rating Design
output Design Heat Rate Exhaust Temperature Exhaust Flow Inlet Pressure Exhaust Pressure GE10/B1
Power Generation Simple Single shaft Counterclockwise ISO Conditions KW KJ/KWh 482 C 47,5 Kg/Sec
100 mmh2o 100 mmh2o Air Compressor Number of stages 11 Type Axial flow Heavy Duty Casing Split
Horizontal Inlet Guide Vane Variable High Flow Turbine Number of stage 3 Turbine Casing Split Horizontal
Exhaust Casing No Split Rotor Speed Rpm Electrical Trip Speed Rpm 5

6 Combustion System Single combustion Chambers Fuel Nozzle Type Spark Plug Spark Plug Type Flame
Detector Arrangement Fuel gas Supply Pressure Flow Bearing Assemblies Quantity Lubrication oil
Pressure Bearing #1 Oil Consumption Bearing #2 Oil Consumption N 1 Bearing Assembly Journal Active
Thrust Inactive Thrust N 2 Bearing assembly Journal Starting System Electric Motor with VFD System Lube
oil System Reservoir Capacity Lube oil pump (Main) Shaft driven on the main gear box Lube oil pump
(auxiliary Cool-down) Electric Pump (DC Motor) Single Gas Single Spark Plug Retractable Electrodes
Double Detector 25BARG 3.600Kg/h 2 Journal Bearing 1 Thrust Bearing 1,4 BAR 275 l/min 39 l/min Tilting-
Pad Tilting-Pad non Equalizing Tilting-Pad non Equalizing Tilting-Pad 110 HP Liter 795 l/min - 3,2BAR
795l/min 3,2BAR 6

7 Lube oil Pump (Emergency) Electrical Pump (AC motor) 490l/min 1,5 BAR Main Lube oil filter Type
Quantity Cartridge type Full flow with transfer valve 2 in parallel (single service) 5 micron filtration, plated
paper Lube oil Cooler Type Air cooler Quantity 1 Approximate Weights Gas Turbine Total weights Turbine
base and piping Kg Kg Options Dual Fuel Nuzzles 7