2 WAY (2/2) SOLENOID VALVE
HERION USA INC.
Valve Technology and Systems
Pilot Operated Brochure 1592
SPECIFICATIONS:
Normally closed valve for air, oil or water 4),5)
Port Sizes: 1/4 to 1 inch NPT
Flow Direction: One Way
Fluid Temperature: 195º F Max (230ºF for EPDM, FKM)
Environmental Temperature: 120º F Max.
Sum of Fluid and Environmental
Temperatures: 265º F Max.
Installation: Solenoid should be vertical for
maximum life
Body Material: Brass
Seat Material: Buna N (NBR)6)
FEATURES:
• Valve operates without pressure differential (∆P=0 psi)
or on Vacuum1)
• High flow rate SSwitching function:
• Easily interchangeable solenoid Normally closed
• Optional seal materials
Operating Pressure PSI Order Number
Port Orifice Spare Parts 3),6)
DC AC Weight 2)
Size Size Kit No. Valve Solenoid
(lb.)
(NPT) (mm) min. max. min. max. (Buna N) DC or AC
CV
1/4” 8 Vac 115 Vac 230 2.3 2.2 12-440-48 82-650-00 .9301
3/8” 10 Vac 115 Vac 230 3.1 2.0 12-440-48 82-651-00 .9301
1/2” 12 Vac 115 Vac 230 3.8 2.0 12-440-48 82-652-00 .9301
3/4” 20 Vac 115 Vac 230 8.4 3.4 12-432-23 82-653-00 .9301
1” 25 Vac 115 Vac 230 9.6 3.2 12-432-23 82-654-00 .9301
1)
Note: For vacuum applications connect vacuum pump to “A” port.
2)
State voltage [V] and frequency [Hz].
3)
Consult factory for other seat materials.
4)
For contaminated fluids insertion of a strainer is recommended, 50 micron or better.
5)
For liquids the maximum allowable viscosity is 25 centistokes.
6)
For EPDM and FKM seals consult Herion.
Solenoid Specifications Standard Voltages Power Consumption
Solenoid DC AC
• Connector to DIN 43650 Form A DC
AC
• 100% Duty Cycle Inrush Holding
50 Hz 60 Hz
• Meets NEMA 4
• Insulation Class F 24 V 24 V --
• Non Polarity Sensitive -- 110 V 120 V .9301 18 W 106 VA 35 VA
• Voltage range + 10% 205 V 230 V 220 V
General Purpose (.9301) Solenoids: General Purpose Connector:
These solenoids include a mating connector. To- A standard cable clamp connector is included with the
gether, the molded coil and connector combination .9301 solenoid. Optional connectors may be selected from
complies with NEMA 4 specifications. A solenoid the table below.
retaining nut secures the solenoid / connector as- Optional Connector Part Number
sembly to the valve. The electrical connection is Standard
Cable Lighted – Cable Clamp
made through the three integral solenoid prongs (2 Clamp 1/2” NPT
power, 1 ground), once the solenoid is “plugged” 24 VAC,VDC 120 VAC 220 VAC
into the connector. The connection is then secured
by tightening the screw provided with the unit. Con- 05-702-75 06-613-74 05-708-18 05-708-16 05-708-17
sult Herion for solenoid voltages or arrangements
not found in this brochure. Options such as lighted 1/2” NPT connectors are also available.
See Brochure N-209.
1/4”, 3/8”, 1’2” 3/4”, 1”
101 Valve body *702 Core
102 Valve cover *703 O-Ring
*103 Diaphragm *705 Pressure Spring
104 Oval cap screw up to 1/2” 1401 Socket
Hexagon cap screw of 3/4” and 1” 1402 Gasket
400 Solenoid 1501 Hexagon Nut
*Parts marked with an asterisk are
701 Core tube contained in the spare parts kit. 1502 O-Ring
Part Port
Number Size B C E F
(NPT)
44 67 90 105
82-650-00 1/4”
(1.73) (2.64) (3.54) (4.13)
44 67 90 105
82-651-00 3/8”
(1.73) (2.64) (3.54) (4.13)
44 67 90 105
82-652-00 1/2”
(1.73) (2.64) (3.54) (4.13)
44 95 104 130
82-653-00 3/4”
(1.73) (3.74) (4.04) (5.12)
44 95 104 130
82-654-00 1”
(1.73) (3.74) (4.04) (5.12)
All Dimensions in mm (inches)
HERION USA INC. • 176 Thorn Hill Road • Warrendale • PA 15086
Phone: 724.776.5577 Fax: 724.776.0310
email:
[email protected] www.herionusa.com
RevRev. 5/02
