ULTRASONIC TRANSDUCER

STANDARD PRODUCT CATALOG

Phased Arrays | High Temperature | Conventional | Wedges

Sensor Networks, Inc.

366 Walker Drive - Suite 200
State College, PA 16801
+1 (814) 466-7207 • [email protected]
© Sensor Networks, Inc. 2022. All rights reserved.
Ver. 7.0 - 10/17/22
WHO
WE Sensor Networks, Inc. (SNI) is a Pennsylvania-based

ARE
technology company specializing in the design and
fabrication of industrial ultrasonic transducers and
tooling for demanding in-situ test and inspection
applications. Engineered for precision, ease of use,
and maximum durability, our offerings include
ultrasonic transducers, fixtures, couplant-delivery
systems, qualification/calibration standards,
procedure development, personnel training and
instrumentation.

SNI’s deep domain expertise enhances NDT

solutions through the selection, design, and
optimization of the ultrasonic technique. The
transducers’ efficiency is paramount for
converting electrical energy into sound, then
coupling and directing that acoustic energy into
the test piece to maximize its signal-to-noise ratio.

With well over 1,000

combined years of NDT
experience, our team of
engineers, technicians,
assemblers, and general
managers have an
extremely deep level of
knowledge and
background in solving
unusual, demanding, and
complicated NDT projects.
 Table of Contents
Table of Contents
PHASED-ARRAY TRANSDUCERS . . . . . 4-17 IMMERSION TRANSDUCERS . . . . . . . 43-49
SMALL FOOTPRINT . . . . . . . . . . . . . . . . . 5 I1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
GENERAL PURPOSE . . . . . . . . . . . . . . . 6-7 I2, I3, I4 . . . . . . . . . . . . . . . . . . . . . . 45-46
LOW PROFILE . . . . . . . . . . . . . . . . . . . . . 8 IR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
PIPELINE / GIRTHWELD . . . . . . . . . . . . . . 9 PAINTBRUSH . . . . . . . . . . . . . . . . . . . . 48
WELD INSPECTION . . . . . . . . . . . . . . . 10-11 MEMBRANE . . . . . . . . . . . . . . . . . . . . . 49
DUAL LINEAR . . . . . . . . . . . . . . . . . . . . . 12
LINEAR CONTACT MEMBRANE . . . . . . . . . 13 CO-POLYMER TRANSDUCERS . . . . . . . . 50
IMMERSION LINEAR. . . . . . . . . . . . . . . . . 14
IMMERSION ANNULAR . . . . . . . . . . . . . . . 15 DUAL-ELEMENT TRANSDUCERS . . . . 51-53
FLEXIBLE ARRAYS . . . . . . . . . . . . . . . . . . 16 ADP . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
WHEELARRAY™ . . . . . . . . . . . . . . . . . . . 17 DU & DU-F . . . . . . . . . . . . . . . . . . . . . . 52
DHT-400 . . . . . . . . . . . . . . . . . . . . . . . 53
MATRIX-ARRAY TRANSDUCERS . . . . . 18-19
DUAL MATRIX & 9x7 . . . . . . . . . . . . . . . . . 18 THICKNESS GAUGING TRANSDUCERS . 54-55
7x4 & TFM. . . . . . . . . . . . . . . . . . . . . . . . 19 SINGLE ELEMENT . . . . . . . . . . . . . . . . . 54
DUAL ELEMENT . . . . . . . . . . . . . . . . . . 54
HIGH-TEMPERATURE TRANSDUCERS . 20-23 TG CASE DIAGRAMS & SIZING . . . . . . . . . 55
HIGH-TEMP LINEAR ARRAYS . . . . . . . . . . . 21
HIGH-TEMP TOFD . . . . . . . . . . . . . . . . . 22 ACCESSORIES . . . . . . . . . . . . . . . . 56-57
HIGH-TEMP CORROSION ARRAY . . . . . . . 23 CONNECTORS, SPLITTERS, & CABLES . . . . 56
SCREWS . . . . . . . . . . . . . . . . . . . . . . . 57
CONVENTIONAL TRANSDUCERS . . . . 24-54
APPENDIX . . . . . . . . . . . . . . . . . . 58-59
CONTACT TRANSDUCERS . . . . . . . . 25-26
CR . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 SENSOR NETWORKS PRODUCT LINES . . . BC
F FINGERTIP . . . . . . . . . . . . . . . . . . . . . 26

DELAY-LINE TRANSDUCERS . . . . . . . 27-29

DFR. . . . . . . . . . . . . . . . . . . . . . . . . . . 27
PENCIL PROBES . . . . . . . . . . . . . . . . . . 28
ZIP . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

ANGLE-BEAM TRANSDUCERS . . . . . . 30-42

MWB+ / MWK+ . . . . . . . . . . . . . . . . . . . 30
ABFP . . . . . . . . . . . . . . . . . . . . . . . . . . 31
AWS & WEDGES . . . . . . . . . . . . . . . . . . 32
SWS & WEDGES . . . . . . . . . . . . . . . . 33-34
MSWS & WEDGES . . . . . . . . . . . . . . . 35-36
TOFD & WEDGES . . . . . . . . . . . . . . . . 37-39
QS & WEDGES. . . . . . . . . . . . . . . . . . 40-42
 PHASED-ARRAY
TRANSDUCERS

GENERAL PURPOSE | IMMERSION | DEEP

PENETRATION | SMALL FOOTPRINT | WEDGE
MOUNT | LOW PROFILE | PIPELINE PROBE |
WELD INSPECTION | ANNULAR | GENERAL
PURPOSE | IMMERSION | DEEP PENETRATION |
SMALL FOOTPRINT | WEDGE MOUNT | LOW
PROFILE | PIPELINE PROBE | WELD INSPECTION |
ANNULAR | GENERAL PURPOSE | IMMERSION |
DEEP PENETRATION | SMALL FOOTPRINT |
WEDGE MOUNT | LOW PROFILE | PIPELINE
4
 Phased Array
Small Footprint

Small footprint arrays are designed with small contact area for inspections in tight
or confined spaces. They can be used for a large variety of inspections including
welds, tubes and pipes, aircraft components, tanks and vessels, and more.
Customizations to arrays and wedges can be special ordered to further optimize
your inspection requirements.

ARRAYS
00-010341
A00 Case
Frequency Number of Element Pitch Elevation SNI Part Cable
Case (MHz) Elements in mm in mm Number** Length
3.5 16 0.016 0.40 0.25 6.25 00-010379 2.5M (8.2 ft.)
5 16 0.016 0.40 0.25 6.25 00-010380 2.5M (8.2 ft.)
0.25" MSWS
7.5 16 0.016 0.40 0.25 6.25 00-010867 2.5M (8.2 ft.)
00-010380
10 16 0.016 0.40 0.25 6.25 00-011207 2.5M (8.2 ft.) 0.25” MSWS

2.25 32 0.016 0.40 0.50 12.7 00-010340 2.5M (8.2 ft.)

3.5 32 0.016 0.40 0.50 12.7 00-010381 2.5M (8.2 ft.)
0.5" MSWS
5 32 0.016 0.40 0.50 12.7 00-010339 2.5M (8.2 ft.)
10 32 0.016 0.40 0.50 12.7 00-010338 2.5M (8.2 ft.)
5 16 0.016 0.40 0.25 6.25 00-011275 2.5M (8.2 ft.)
A0 00-010339
10 16 0.016 0.40 0.25 6.4 00-013027 2.5M (8.2 ft.) 0.5” MSWS

A00 10 16 0.012 0.31 0.20 5 00-010341 2.5M (8.2 ft.)

All arrays come standard with IPEX connectors unless specified. See page 56 for connector types.

WEDGES
Dimensions
Wedge Type Description Part Number
Length Width Height
REX, 35-75 Shear Wave, Flat 01-010705 0.75 in. 19 mm 0.70 in. 17.8 mm 0.38 in. 9.7 mm
0.25" MSWS
REX, 35-75 L-WAVE, Flat 01-010977 0.58 in. 14.7 mm 0.70 in. 17.8 mm 0.28 in. 7.1 mm
H
REX, 35-75 Shear Wave, Flat 01-011015 1.20 in. 30.5 mm 0.95 in. 24.1 mm 0.70 in. 17.8 mm
0.5" MSWS
REX, 35-75 L-WAVE, Flat 01-011016 0.81 in. 20.6 mm 0.95 in. 24.1 mm 0.35 in. 8.9 mm
W
30-60 Shear 01-010710 0.83 in. 21.1 mm 0.55 in. 14 mm 0.47 in. 11.9 mm
A00 L
45-70 Shear 01-010711 0.83 in. 21.1 mm 0.55 in. 14 mm 0.51 in. 13 mm

CASE DIMENSIONS
Case Dimensions A0 A00 0.25” MSWS 0.5” MSWS
Case Type Length Width Height
W
A0 0.41 in. 10.3 mm 0.5 in. 12.6 mm 0.91 in. 23.1 mm H
L
A00 0.31 in. 7.9 mm 0.31 in. 7.9 mm 0.91 in. 23.1 mm H
H H
0.25 MSWS 0.5 in. 12.7 mm 0.37 in. 9.4 mm 0.5 in. 12.7 mm
0.5 MSWS 0.76 in. 19.3 mm 0.61 in. 15.5 mm 0.75 in. 19 mm L W W
W L L
5
 Phased Array
General Purpose Linear

General purpose linear arrays are versatile arrays that optimize a wide range of applications including
weld inspection, tube and pipe inspection, turbine blades, rails, pressure vessels, and many more.
Varying in frequency, number of elements, and element pitch and elevation, the wide variety of arrays
available provide many options when choosing an array for your application. Custom options are
available upon request.

ARRAYS
Frequency Number of Element Pitch Elevation SNI Part Cable
Case (MHz) Elements in mm in mm Number Length
2.25 16 0.030 0.75 0.47 12 00-011419 2.5M (8.2 ft.)
A1 5 16 0.024 0.60 0.39 10 00-011423 2.5M (8.2 ft.) 00-011422
10 32 0.012 0.31 0.28 7 00-011430 2.5M (8.2 ft.)
A10 Case
2.25 8 0.047 1.20 0.39 10 00-013030 2.5M (8.2 ft.)
3.5 8 0.047 1.20 0.39 10 00-013031 2.5M (8.2 ft.)
5 16 0.024 0.60 0.39 10 00-011422 2.5M (8.2 ft.)
A10
5 32 0.012 0.30 0.39 10 00-011651 2.5M (8.2 ft.)
7.5 32 0.012 0.30 0.39 10 00-013028 2.5M (8.2 ft.)
10 32 0.012 0.31 0.28 7 00-011429 2.5M (8.2 ft.)
2.25 32 0.024 0.60 0.39 10 00-011781 3.0M (9.2 ft.)
5 16 0.040 1.00 0.39 10 00-011836 3.0M (9.2 ft.)

A11
5 32 0.024 0.60 0.39 10 00-010329 2.5M (8.2 ft.)
00-010277
5 64 0.012 0.30 0.39 10 00-013036 2.5M (8.2 ft.) E3 Case
10 64 0.012 0.30 0.39 10 00-013037 2.5M (8.2 ft.)
15 64 0.012 0.30 0.39 10 00-013038 2.5M (8.2 ft.)
2.25 64 0.024 0.60 0.39 10 00-011420 2.5M (8.2 ft.)
2.25 64 0.030 0.75 0.47 12 00-011421 2.5M (8.2 ft.)
3.5 64 0.024 0.60 0.39 10 00-012459 2.5M (8.2 ft.)
A12
5 64 0.024 0.60 0.39 10 00-011426 2.5M (8.2 ft.)
5 128 0.012 0.30 0.39 10 00-013040 2.5M (8.2 ft.)
10 64 0.024 0.60 0.39 10 00-013039 2.5M (8.2 ft.)
5 64 0.024 0.60 0.39 10 00-011427 2.5M (8.2 ft.)
A2
10 64 0.024 0.60 0.28 7 00-013041 2.5M (8.2 ft.)
00-010266
A3 5 16 0.047 1.20 0.47 12 00-011926 2.5M (8.2 ft.) AM Case
2.25 16 0.030 0.75 0.47 12 00-010265 2.5M (8.2 ft.)
AM
5 16 0.024 0.60 0.39 10 00-010266 2.5M (8.2 ft.)
E1 4 16 0.020 0.50 0.35 9 00-010275 2.5M (8.2 ft.)
E2 1.5 16 0.040 1.00 0.47 12 00-010276 2.5M (8.2 ft.)
E3 2.25 16 0.060 1.50 0.75 19 00-010277 2.5M (8.2 ft.)
2.25 64 0.024 0.60 0.39 10 00-010267 2.5M (8.2 ft.)
LM 5 64 0.024 0.60 0.39 10 00-010268 2.5M (8.2 ft.)
10 64 0.024 0.60 0.39 10 00-010269 2.5M (8.2 ft.)

All arrays come standard with IPEX connectors unless specified. See page 56 for connector types.

6
 Phased Array
General Purpose Linear

WEDGES
Dimensions
Wedge Type Description Part Number
Length Width Height
0 Degree Delay, 20mm 01-011733 1.14 in. 29 mm 1.18 in. 30 mm 0.79 in. 20 mm
A1
N60S (45-70 Shear), flat, porting, wear pins, 8mm gimbal holes 01-011734-IHC 1.20 in. 30.5 mm 1.58 in. 40.1 mm 0.64 in. 16.3 mm
0 Degree Delay, 20mm 01-011741 2.56 in. 65 mm 1.18 in. 30 mm 0.79 in. 20 mm
A2
N55S (30-70 Shear), flat, porting, wear pins, 8mm gimbal holes 01-011742-IHC 2.70 in. 68.6 mm 1.58 in. 40.1 mm 1.70 in. 43.2 mm
0 Degree Delay, 20mm 01-011735 0.98 in. 24.9 mm 0.91 in. 23.1 mm 0.79 in. 20 mm
N55S (30-70 Shear), Flat, No porting, No Wear Pins, 8mm gimbal holes 01-013460 0.91 in. 23.1 mm 0.91 in. 23.1 mm 0.56 in. 16.5 mm
A10
N55S (30-70 Shear), flat, porting, wear pins, 8mm gimbal holes 01-013460-IHC Contact for dimensions
IHC Ring, ported wedge ring with wear pins 01-011514 Contact for dimensions
0 Degree Delay, 20mm 01-011749 1.38 in. 35.1 mm 0.91 in. 23.1 mm 0.91 in. 23.1 mm
N55S (30-70 Shear), flat, no porting, 4mm gimbal holes 01-010709 1.63 in. 41.4 mm 0.91 in. 23.1 mm 1.13 in. 28.7 mm
A11
N55S (30-70 Shear), flat, porting, wear pins, 4mm gimbal holes 01-010709-IHC Contact for dimensions
IHC Ring, ported wedge ring with wear pins 01-012303 Contact for dimensions
0 Degree Delay, 20mm 01-012517 2.28 in. 57.9 mm 0.91 in. 23.1 mm 0.79 in. 20 mm
N55S (30-70), flat, no porting, 4mm gimbal holes 01-012516 2.88 in. 73.2 mm 0.91 in. 23.1 mm 1.76 in. 44.7 mm
A12
N55S (30-70), flat, porting, wear pins, 8mm gimbal holes 01-012516-IHC Contact for dimensions
IHC Ring, ported wedge ring with wear pins 01-012315 Contact for dimensions
REX, 38.0 DEG INC, Flat, A 01-010293 0.75 in. 19.1 mm 1.10 in. 27.9 mm 0.60 in. 15.2 mm
E1 REX, 38.0 DEG INC, Flat, B 01-010294 0.65 in. 16.5 mm 1.10 in. 27.9 mm 0.60 in. 15.2 mm
30-70 Shear 01-011731 0.97 in. 24.6 mm 1.11 in. 28.2 mm 0.59 in. 15 mm
REX, 38.0 DEG INC, Flat, A 01-010295 1.12 in. 28.4 mm 0.82 in. 20.8 mm 0.82 in. 20.8 mm
E2
REX, 38.0 DEG INC, Flat, B 01-010296 0.77 in. 19.6 mm 0.82 in. 20.8 mm 0.82 in. 20.8 mm
E3 REX, 38.0 DEG INC, Flat 01-010297 1.83 in. 46.5 mm 1.50 in. 38.1 mm 1.29 in. 32.8 mm
0 Degree Delay, 20mm 01-011975 1.25 in. 31.8 mm 1.18 in. 30 mm 0.79 in. 20 mm
AM 40-70S 01-010703 0.93 in. 23.6 mm 1.18 in. 30 mm 0.47 in. 11.9 mm
40-70L 01-010531 0.98 in. 24.9 mm 1.18 in. 30 mm 0.92 in. 23.4 mm
0 Degree 01-010706 2.00 in. 50.8 mm 1.10 in. 27.9 mm 0.79 in. 20.1 mm
LM 40-70S 01-010707 2.60 in. 66 mm 1.10 in. 27.9 mm 1.35 in. 34.3 mm
40-70L 01-010708 2.27 in. 57.7 mm 1.10 in. 27.9 mm 1.40 in. 35.6 mm

W
L

CASE DIMENSIONS
Case Dimensions A1 A2 A10 A11 A12
Case Type Length Width Height
A1 0.67 in. 17 mm 1.09 in. 27.7 mm 0.99 in. 25.1 mm
A2 2.09 in. 53.1 mm 1.14 in. 29 mm 1.36 in. 34.5 mm H
H
A10 0.91 in. 23.1 mm 0.63 in. 16 mm 0.79 in. 20.1 mm H H H
W L
A11 0.98 in. 24.9 mm 0.91 in. 23.1 mm 0.79 in. 20.1 mm W L L L
W L
W W
A12 1.77 in. 45 mm 0.91 in. 23.1 mm 0.79 in. 20.1 mm
E1 1.1 in. 27.9 mm 0.59 in. 15 mm 1.06 in. 26.9 mm E1 E2 E3 AM LM
E2 0.75 in. 19 mm 0.75 in. 19 mm 1.0 in. 25.4 mm
W
E3 1.45 in. 36.8 mm 1.25 in. 31.8 mm 1.0 in. 25.4 mm
H
AM 1.18 in. 30 mm 0.63 in. 16 mm 0.98 in. 24.9 mm H H H H
LM 1.69 in. 42.9 mm 1.1 in. 27.9 mm 0.98 in. 24.9 mm W
W L
L W L W L L 7
 Phased Array
Low Profile - Small Diameter Weld Inspection

Low-profile arrays are designed to inspect small 00-011212 00-011875

diameter or thin-walled pipes for flaws and defects. A15 Case A25 Case
A15 and A25 cases are also usefull for applications
with low clearance at the inspection area.
Low-profile wedges optimize the arrays for
small-diameter weld inspection. Custom arrays and
wedges can be ordered upon request.

ARRAYS
Frequency Number of Element Pitch Elevation SNI Part Cable
Case (MHz) Elements in mm in mm Number** Length
5 16 0.020 0.50 0.38 10 00-011211 2.5M (8.2 ft.)
7.5 16 0.020 0.50 0.38 10 00-011212 2.5M (8.2 ft.)
A15 7.5 32 0.010 0.25 0.38 10 00-011213 2.5M (8.2 ft.)
10 16 0.020 0.50 0.38 10 00-011214 2.5M (8.2 ft.)
10 32 0.010 0.25 0.38 10 00-011215 2.5M (8.2 ft.)
3.5 16 0.030 0.75 0.20 5 00-011857 3.0M (9.2 ft.)
A25
5 16 0.030 0.75 0.20 5 00-012963 2.5M (8.2 ft.)
All arrays come standard with IPEX connectors unless specified. See page 56 for connector types.

WEDGES
Dimensions
Wedge Type Description Part Number
Length Width Height
SA-N60S-IH, Flat, Porting, No Wear Pins, 0.12" (3mm) Gimbal Holes 01-011230-IH 0.72 in. 18.3 mm 0.86 in. 21.8 mm 0.44 in. 11.2 mm
SA15-N60S-IH-AOD2.375, Axial OD Cut, Porting, No Wear Pins, 0.12" (3mm) Gimbal Holes 01-011230-IH-AOD2.375 0.72 in. 18.3 mm 0.86 in. 21.8 mm 0.44 in. 11.2 mm
A15
SA15-N60S-IH-AOD3.50, Axial OD Cut, Porting, No Wear Pins, 0.12" (3mm) Gimbal Holes 01-011230-IH-AOD3.50 0.72 in. 18.3 mm 0.86 in. 21.8 mm 0.44 in. 11.2 mm
SA15-N60S-IH-AOD4.50, Axial OD Cut, Porting, No Wear Pins, 0.12" (3mm) Gimbal Holes 01-011230-IH-AOD4.50 0.72 in. 18.3 mm 0.86 in. 21.8 mm 0.44 in. 11.2 mm
A25 22-Deg Inc, 3.80-Deg Roof, Flat (Only works with SNI A25 arrays) 01-013122 Contact for dimensions

Custom curves on wedges can be done upon request.

W
L

CASE DIMENSIONS
Case Dimensions A15 A25
Case Type Length Width Height
A15 1.03 in. 26.2 mm 0.86 in. 21.8 mm 0.39 in. 9.9 mm L
A25 0.70 in. 17.8 mm 0.47 in. 11.9 mm 0.54 in. 13.7 mm
H
W
L
H W

8
 Phased Array
Pipeline / Girthweld

Pipeline and girthweld arrays are designed to be paired with instruments for
automatic inspection systems. Manual inspections can also be conducted
with these arrays. They are perfect for scanning large or small diameter
pipes for flaws & defects as well as weld integrity inspection. Sensor
Networks pipeline and girthweld arrays can be built with any connector and
customized for your manual or automated inspection system.

ARRAYS
Frequency Number of Element Pitch Elevation SNI Part Cable
Case (MHz) Elements in mm in mm Number** Length
5 60 0.040 1.00 0.38 10 00-011425 2.5M (8.2 ft.)
A14
7.5 60 0.040 1.00 0.38 10 00-011428 2.5M (8.2 ft.)
2.25 60 0.040 1.00 0.38 10 00-013047 2.5M (8.2 ft.)
PWZ1 5 60 0.040 1.00 0.38 10 00-012896 2.5M (8.2 ft.)
7.5 60 0.040 1.00 0.38 10 00-012949 2.5M (8.2 ft.)
All arrays come standard with IPEX connectors unless specified. See page 56 for connector types.

WEDGES
Dimensions
Wedge Type Description Part Number
Length Width Height
A14 SA14-N55S, Flat, No Porting, Gimbal Holes: M3, 0.16" (4mm) and 0.16" Slot, 30-70S in CS 01-011740 Contact for dimensions
PWZ1 SPWZ1-N50S-IHC, 33.7-Deg Inc, Flat 01-010665-IHC 3.23 in. 82 mm 1.5 in. 38.1 mm 1.73 in. 43.9 mm

Case
Accessory Part Number
Style
A14 IHC Ring 01-012265
H

W
L

CASE DIMENSIONS

Case Dimensions A14 PWZ1

Case Type Length Width Height
A14 2.67 in. 67.8 mm 0.91 in. 23.1 mm 0.79 in. 20.1 mm
PWZ1 2.67 in. 67.8 mm 1.02 in. 25.9 mm 1.19 in. 30.2 mm H

H
L L

W
W

9
 Phased Array
Weld Inspection

Weld inspection arrays paired with the right phased-array wedge

are perfect for conducting inspections on various weld, plate, and
forging applications. Various options for arrays and wedges offer
the ability to meet and optimize inspection requirements. Custom
array and wedge options are available upon request.

ARRAYS
Frequency Number of Element Pitch Elevation SNI Part Cable
Case (MHz) Elements in mm in mm Number** Length
0.5 16 0.110 2.80 1.02 26 00-011821 5M (16.4 ft.)
A4 1.5 16 0.110 2.80 1.02 26 00-011416 2.5M (8.2 ft.)
2.25 16 0.080 2.00 1.26 32 00-011417 2.5M (8.2 ft.)
2.25 32 0.030 0.75 0.94 24 00-011418 2.5M (8.2 ft.)
A5
5 32 0.024 0.60 0.76 20 00-011424 2.5M (8.2 ft.)
5 32 0.024 0.60 0.39 10 00-011925 2.5M (8.2 ft.)
A31 7.5 32 0.024 0.60 0.39 10 00-012621 2.5M (8.2 ft.)
10 32 0.024 0.60 0.39 10 00-013043 2.5M (8.2 ft.)
5 32 0.040 1.00 0.39 10 00-011839 2.5M (8.2 ft.)
A32 5 64 0.020 0.50 0.39 10 00-011503 2.5M (8.2 ft.)
10 64 0.020 0.50 0.39 10 00-011924 2.5M (8.2 ft.)
AWS 2.25 16 0.040 1.00 0.63 16 00-010477 2.5M (8.2 ft.)
E1 2 8 0.040 1.00 0.35 9 00-010274 2.5M (8.2 ft.)

All arrays come standard with IPEX connectors unless specified. See page 56 for connector types.

00-011821 00-011418 00-011839

A4 Case A5 Case A32 Case

10
 Phased Array
Weld Inspection

CASE DIMENSIONS

A4 A5 AWS Case Dimensions

Case Type Length Width Height
A4 2.24 in. 56.9 mm 1.81 in. 46 mm 1.18 in. 30 mm
C
H
H A5 1.14 in. 29 mm 1.69 in. 42.9 mm 0.94 in. 23.9 mm
W L W
L A B AWS 1.26 in. 32 mm 0.80 in 20.3 mm 0.75 in. 19 mm
A31 1.20 in. 30.5 mm 1.10 in. 27.9 mm 0.98 in. 24.9 mm
A32 1.58 in. 40.1 mm 1.10 in. 27.9 mm 1.0 in. 25.4 mm
A31 A32

H
H

W L
W L

WEDGES

Dimensions
Wedge Type Description Part Number
Length Width Height
A4 30-70 Shear 01-011744 3.39 in. 86.1 mm 1.85 in. 47 mm 1.77 in. 45 mm
A5 30-70 Shear 01-011746 1.56 in. 39.6 mm 1.71 in. 43.4 mm 0.63 in. 16 mm
N55S (30-70 shear), flat, no porting, 4mm (0.16") gimbal holes 01-013300 1.91 in. 48.5 mm 1.18 in. 30 mm 1.26 in. 32 mm
A31
N55S (30-70 shear), flat, porting, wear pins, wear bars, 8mm (0.32") gimbal holes 01-013300-IHC Contact for dimensions
A32 N55S (30-70 shear), flat, no porting, 4mm (0.16") gimbal holes 01-013301 2.42 in. 61.5 mm 1.18 in. 30 mm 1.26 in. 32 mm

W
L

11
 Phased Array
Ambient Temp - Dual-Linear Phased Array™

DUAL LINEAR

Dual-Linear Phased Array transducers are optimized for corrosion and erosion inspection up to
100°C (212°F). All models provide 32 or more transmit/receive elements that provide larger beam
coverage than conventional dual-element transducers allowing for more efficient inspection time.
These arrays also provide increased POD for pits in corrosion applications. Replaceable wear plates
can be be curved to match pipe diameters. See page 23 for High-Temp Dual-Linear Phased Arrays.

00-010863
Frequency Number of Element Pitch Elevation SNI Part Cable CL
Case (MHz) Elements in mm in mm Number Length
32 Transmit
CL 5 0.060 1.50 0.20 5 00-010863 3.0M (9.2 ft.)
32 Receive
32 Transmit
CS 5 0.030 0.75 0.20 5 00-011200 3.0M (9.2 ft.)
32 Receive
64 Transmit
CS 10 0.014 0.35 0.20 5 00-012676 3.0M (9.2 ft.)
64 Receive

Removable 32 Transmit
7.5 0.060 1.50 0.20 5 00-013062 2.5M (8.2 ft.)
Delay 32 Receive 00-012676
CS
All arrays come standard with IPEX connectors unless specified. See page 56 for connector types.

WEAR BARS

Case Type Description Part Number

CS Ported Wear Plate, Flat, Porting 01-011541

CL Ported Wear Plate, Flat, Porting 01-011430
Removable Removable Sled, 3mm (0.12") gimbal holes 01-011541

Wear bars and sleds can be curved upon request.

Wear bars can have 3mm (0.12”) or 5mm (0.2”) gimbal holes.

CASE DIMENSIONS
Case Dimensions CL CS W
Case Type Width Length Height W
CL 0.95 in. 24.1 mm 2.58 in. 65.5 mm 1.0 in. 25.4 mm
CS 0.95 in. 24.1 mm 1.61 in. 40.9 mm 1.0 in. 25.4 mm
Removable 1.25 in. 31.8 mm 2.58 in. 65.5 mm 1.20 in. 30.5 mm
H L
H L
REMOVABLE W

Ha
Hb

L
12
 Phased Array
Linear Contact Membrane

CONTACT MEMBRANE

Contact membrane arrays are linear arrays specially designed

and optimized for inspection of threaded bolts or applications
with rough surfaces. The membrane allows for effective coupling
on those rough surfaces and can be replaced to extend the life of
the array. Contact membrane transducers have side-mounted
cables but can be special ordered with top-mounted cables.

Frequency Number of Element Pitch Elevation SNI Part Cable

Case (MHz) Elements in mm in mm Number** Length
A24 4 16 0.040 1.00 0.63 16 00-011927 2.5M (8.2 ft.)
Illustration of the
2 16 0.060 1.50 0.94 24 00-011903 2.5M (8.2 ft.)
BS ceramic in a contact
4 16 0.060 1.50 0.94 24 00-011902 2.5M (8.2 ft.) membrane linear array.
2 16 0.025 0.63 0.39 10 00-011714 2.5M (8.2 ft.)
MB S
4 16 0.025 0.63 0.39 10 00-011715 2.5M (8.2 ft.)

All arrays come standard with IPEX connectors unless specified. See page 56 for connector types.

00-011927 00-011903 00-011715

A24 Case B S Case MB S Case

CASE DIMENSIONS

A24 BS MB S Case Dimensions

Case Type A B
A24 1.07 in. 27.2 mm 1.75 in. 44.5 mm
MB S 0.98 in. 24.9 mm 1.61 in. 40.1 mm
BS 1.77 in. 45 mm 2.41 in. 61.2 mm

13
 Phased Array
Immersion Linear

IMMERSION LINEAR

Much like conventional immersion transducers, immersion arrays

are used in automatic and manual scanning systems using water or
other liquid to couple to parts with complex geometries or large
surface areas. Immersion inspection offers near-surface resolution
superior to that of contact transducers. Immersion transducers are
also effective for inspection of composite materials.

Frequency Number of Element Pitch Elevation SNI Part Cable

Case (MHz) Elements in mm in mm Number** Length
HW 5 64 0.050 1.27 0.31 8 00-010327 2.5M (8.2 ft.)
5 64 0.024 0.60 0.39 10 00-011431 2.5M (8.2 ft.)
I1
10 64 0.024 0.60 0.39 10 00-012739 2.5M (8.2 ft.)
5 128 0.024 0.60 0.38 10 00-011432 2.5M (8.2 ft.)
I2
10 128 0.020 0.50 0.28 7 00-013044 2.5M (8.2 ft.)
2.25 128 0.030 0.75 0.47 12 00-013045 5M (16.4 ft.)
I3
5 128 0.030 0.75 0.38 10 00-010333 5M (16.4 ft.)
5 64 0.040 1.00 0.28 7 00-012746 3M (9.8 ft.)
I4
7.5 64 0.040 1.00 0.28 7 00-012745 7M (23 ft.)
3.5 64 0.040 1.00 0.28 7 00-010331 5M (16.4 ft.)
Near Wall 1
5 64 0.040 1.00 0.28 7 00-010332 5M (16.4 ft.)
3.5 128 0.040 1.00 0.28 7 00-013046 2.5M (8.2 ft.)
Near Wall 3
5 128 0.040 1.00 0.28 7 00-011929 2.5M (8.2 ft.)
R4 5 32 0.052 1.32 0.24 6 00-010334 5M (16.4 ft.)
All arrays come standard with IPEX connectors unless specified. See page 56 for connector types.

CASE DIMENSIONS
Case Dimensions
Case Type Length Width Height
I1 I2 I3
I1 1.97 in. 50 mm 0.75 in. 19 mm 0.98 in. 24.9 mm
I2 3.27 in. 83.1 mm 0.83 in. 21.1 mm 1.38 in. 35.1 mm
I3 4.02 in. 102.1 mm 0.83 in. 21.1 mm 1.38 in. 35.1 mm

H H I4 3.08 in. 78.2 mm 0.97 in. 24.6 mm 1.00 in. 25.4 mm

H
L R4 1.67 in. 45.2 mm 0.59 in. 15 mm 1.67 in. 42.4 mm
L
W L W
W HW 3.4 in. 86.4 mm 0.5 in. 12.7 mm 1.25 in. 31.8 mm
Near Wall 1 2.6 in. 66 mm 0.75 in. 19 mm 0.98 in. 24.9 mm
I4 R4 HW Near Wall 3
Near Wall 3 5.12 in. 130 mm 0.83 in. 21.1 mm 1.38 in. 35.1 mm

L
Near Wall 1 Near Wall 3

H W H
L L
W H
W
H H
L
L
14 W W
 Phased Array
Immersion Annular

IMMERSION ANNULAR

Much like conventional immersion transducers, immersion arrays

are used in automatic and manual scanning systems using water or
other liquid to couple to parts with complex geometries or large
surface areas. Immersion inspection offers near-surface resolution
superior to that of contact transducers. Immersion transducers are
also effective for inspection of composite materials.

Element Element
Frequency Number of Diameter Diameter SNI Part Cable
Case (MHz) Elements inches mm Number** Length
5 16 1.0 25.4 00-011892 2.5M (8.2 ft.)
Annular
10 16 1.0 25.4 00-011893 2.5M (8.2 ft.)
All arrays come standard with IPEX connectors unless specified. See page 56 for connector types.

CASE DIMENSIONS

Case Dimensions
Case Type A B
Annular 1.4 in. 35.5 mm 1.6 in. 40.6 mm

Example of the ceramic in

an annular array.

15
 Phased Array
Flexible Array

FLEXIBLE PHASED ARRAY

Flexible arrays are perfect for applications on curved
metals and composites and can flex to fit a wide
range of radii. Flexible arrays improve the
inspection on complex geometry by reducing
distortion and loss of sensitivity created by
complex coupling requirements. Sensor
Networks’ flexible arrays are designed to meet
the needs of various complex inspections
with increased flaw detection and quicker
inspection time.

PART NUMBERS
Frequency* Number of Element Pitch Elevation SNI Part
(MHz) Elements in mm in mm Array Description and Application Number

5 64 0.04 1 0.28 7 NDT and thickness measurement of curved surfaces 00-012703

7 64 0.04 1 0.28 7 NDT and thickness measurement of curved surfaces 00-012975

All arrays come standard with IPEX connectors unless specified. See page 56 for connector types.
Custom cable length available.

CASE DIMENSIONS W
Case Dimensions
La H W Lb
2.57 in. 65.3 mm 0.64 in. 16.3 mm 1.27 in. 32.3 mm 4.7 in. 119.4 mm
H

La

Lb

16
 Phased Array
WheelArray™

WHEELARRAY

The WheelArray is a unique tool and ultrasonic test

fixture used to increase inspection productivity of
large surface areas associated with composite
materials and metal plates. WheelArray is offered in
five test frequencies and the wheel can be
replaced or swapped out by the end-user in the
field.

Prior to inspection, a small quantity of water or

other suitable couplant needs to be sprayed on the
test area.

Custom WheelArrays can be requested including

custom frequency, elements, pitch, cable length,
and connector.

COMPLETE WHEELARRAY KIT

Frequency* Number of Element Pitch Elevation Sound Path Beam Width
Part Number
(MHz) Elements in mm in mm in mm in mm
1 32 0.06 1.6 0.47 12 1.0 25.4 2.0 51.2 00-013242
2.25 64 0.03 0.8 0.25 6.4 1.0 25.4 2.0 51.2 00-013241
3.5 64 0.03 0.8 0.25 6.4 1.0 25.4 2.0 51.2 00-013076
5 64 0.03 0.8 0.25 6.4 1.0 25.4 2.0 51.2 00-013073
10 64 0.03 0.8 0.25 6.4 1.0 25.4 2.0 51.2 00-013081
All arrays come standard with IPEX connectors unless specified. See page 56 for connector types.

REPLACEMENT WHEEL
Frequency* Number of Element Pitch Elevation Sound Path Beam Width
Part Number
(MHz) Elements in mm in mm in mm in mm
1 32 0.06 1.6 0.47 12 1.0 25.4 2.0 51.2 00-013233
2.25 64 0.03 0.8 0.25 6.4 1.0 25.4 2.0 51.2 00-013232
3.5 64 0.03 0.8 0.25 6.4 1.0 25.4 2.0 51.2 00-013228
5 64 0.03 0.8 0.25 6.4 1.0 25.4 2.0 51.2 00-013227
10 64 0.03 0.8 0.25 6.4 1.0 25.4 2.0 51.2 00-013229

5.68” (144mm) 8.32” (211mm)

4.85” (123mm)

17
 Matrix Arrays
Dual Matrix and 9x7

MATRIX ARRAYS

Matrix-Array transducers enable enhanced phased-array inspections and

full-matrix capture which brings better POD, improved flaw sizing &
characterization, enhanced imaging and faster inspection scans. Whether
it’s a simple 4 x 8 element array for weld inspection or as complicated as an
800-element array for heavy-wall forgings, SNI can prove-out a design in 3D Example of a plated
computer simulation and easily change key variables such as frequency 8x4 matrix array
and pitch before the final design and fabrication process begins. ceramic.

DUAL MATRIX
Frequency Number of Primary Pitch Secondary Pitch SNI Part Cable
(MHz) Elements in mm in mm Array Description and Application Number** Length Case
2x15
1.5 0.150 3.80 0.160 4 Dual matrix (T/R) - coarse-grain materials 00-010278 2.5M (8.2 ft.) E4
5x3 element
2x32
2 0.070 1.75 0.160 4 Dual matrix (T/R) - coarse-grain materials 00-010342 2.5M (8.2 ft.) E5
16x2 element
2x32
4 0.040 1.00 0.120 3 Dual matrix (T/R) - coarse-grain materials 00-013823 2.5M (8.2 ft.) A27
16x2 element

9x7
Frequency Number of Primary Pitch Secondary Pitch SNI Part Cable
(MHz) Elements in mm in mm Array Description and Application Number** Length Case

5 63 0.043 1.10 0.043 1.1 General Purpose 00-013821 2.5M (8.2 ft.) AM

2.25 63 0.070 1.75 0.070 1.75 General Purpose 00-013822 2.5M (8.2 ft.) AL

00-010278 00-010342 00-013823

E4 Case E5 Case A27 Case

* See page 56 for matrix-array transducer connector types.

** When ordering matrix-array transducers, please include the
18 part number followed by the desired connector type (ex. 00-010328 ZPAC).
 Matrix Arrays
7x4 and TFM Arrays

7x4

Frequency Number of Primary Pitch Secondary Pitch SNI Part Cable

(MHz) Elements in mm in mm Array Description and Application Number** Length Case

2.25 28 0.106 2.70 0.120 3 General Purpose 00-013824 2.5M (8.2 ft.) A17

TFM ARRAYS

Frequency Number of SNI Part

Total Focusing Method (TFM) is an algorythm used to
Case (MHz) Elements Number** Cable translate the inspection information gathered from
64 00-011904 3.0M (3.3 ft) Full Matrix Capture (FMC). This process allows for an
5
64 00-011905 3.0M (3.3 ft) enhanced imaging by focusing at all points within the
AL 7.5 64 00-012898 3.0M (3.3 ft) inspection area.
64 00-011906 3.0M (3.3 ft)
10
64 00-011907 3.0M (3.3 ft)

CASE DIMENSIONS

E4 E5 AM Case Dimensions
Case Type Length Width Height
W
E4 1.33 in. 33.8 mm 0.65 in. 16.5 mm 1.0 in. 25.4 mm
E5 1.41 in. 35.8 mm .62 in. 15.7 mm 1.0 in. 25.4 mm
H H H
AM 1.18 in. 30 mm 0.63 in. 16 mm 0.98 in. 24.9 mm
L L A17 1.34 in. 34 mm 0.63 in. 16 mm 0.98 in. 24.9 mm
L W W A27 1.12 in. 28.4 mm 0.39 in. 9.9 mm 0.79 in. 20.1 mm
LM 1.69 in. 42.9 mm 1.1 in. 27.9 mm 0.98 in. 24.9 mm

A17 A27 AL

H
H
H
L L
L W
W

Wedges for these arrays usually require very specific customization depending on the
application. Please contact us to discuss your wedge requirements.

* See page 56 for matrix-array transducer connector types.

** When ordering matrix-array transducers, please include the
19
part number followed by the desired connector type (ex. 00-010328 ZPAC).
 UT FLAW DETECTION TRANSDUCERS

Covering Flaw Scanning and Sizing

from Standard to Elevated
Temperatures all in One Transducer
If you’re inspecting or planning to perform on-line, elevated temperature flaw detection
using linear phased-array, TOFD or dual-linear arrays for corrosion detection and mapping,
SNI has a better solution for you. We have developed and done extensive testing on a
family of PAUT arrays, transducers, and wedges that can operate at up to 200°C (392°F)
continuous metal-surface temperatures.

Changes in the transducers and the wedge’s resultant refracted angle, due to
temperature change, is predictable and can be managed and compensated for in the
calibration process. The attached data shows the temperature effects on both
attenuation, frequency, velocity, and refracted angle. The new transducer designs are
engineered with materials capable of transitioning and operating at these higher
temperatures associated with on-line Oil & Gas and Power Gen applications thereby
enabling the inspection and protecting the user’s investment in the various transducers.

CONTINUOUS
USE UP TO
EXTENDED-TEMP-RANGE
TRANSDUCER

INTERCHANGEABLE- STANDARD MID-TEMP HIGH-TEMP

TEMP-RANGE WEDGES REXOLITE PEEK CELAZOLE

$ $$ $$$

0° 50° 100° 150° 200° 0° 50° 100° 150° 200° 0° 50° 100° 150° 200°
Celsius Celsius Celsius

20 One Transducer for All Your Standard AND High-Temp Applications

 High-Temp Linear
A10 & A11 Arrays

High-Temperature Linear Arrays are versatile

arrays that optimize a wide range of
high-temp applications including weld
inspection, tube and pipe inspection, rails,
pressure vessels, and many more. These arrays
come standard with 2.5 meter (8.2 ft.) cables
with IPEX connectors. Wedges for these arrays
are available in two options: Mid Temp [100°C
to 150°C (212°F to 302°F)] and High Temp
[150°C to 200°C (302°F to 392°F)]. Each wedge
type is also available in 30-70° and 0° refracted
angle models.

ARRAYS
Frequency Number of Element Pitch Elevation SNI Part
Case (MHz) Elements in mm in mm Number
A10 5 16 0.024 0.60 0.39 10 00-015631
A11 5 32 0.024 0.60 0.39 10 00-015632

WEDGES
Wedges
Case Style Temp Range Angle* Part Number Length Width Height

Mid Temp (100°C to 150°C) 0° 01-013350-IHC 0.98 in. 24.9 mm 1.58 in. 40.1 mm 0.79 in. 20.1 mm
High Temp (150°C to 200°C) 0° 01-013351-IHC 0.98 in. 24.9 mm 1.58 in. 40.1 mm 0.79 in. 20.1 mm
A10
Mid Temp (100°C to 150°C) N55S (30-70°) 01-013352-IHC 0.91 in. 23.1 mm 1.30 in. 33 mm 0.56 in. 14.2 mm
High Temp (150°C to 200°C) N55S (30-70°) 01-013353-IHC 1.40 in. 35.6 mm 1.58 in. 40.1 mm 0.70 in. 17.8 mm
Mid Temp (100°C to 150°C) 0° 01-013355-IHC 1.38 in. 35.1 mm 1.58 in. 40.1 mm 0.79 in. 20.1 mm
High Temp (150°C to 200°C) 0° 01-013356-IHC 1.38 in. 35.1 mm 1.58 in. 40.1 mm 0.79 in. 20.1 mm
A11
Mid Temp (100°C to 150°C) N55S (30-70°) 01-013357-IHC 1.63 in. 41.4 mm 1.30 in. 33 mm 1.13 in. 28.7 mm
High Temp (150°C to 200°C) N55S (30-70°) 01-013358-IHC 2.25 in. 57.2 mm 1.30 in. 33 mm 1.05 in. 26.7 mm

All wedges come standard with 8mm ø (0.31 in.) gimbal-mounting holes.

A A

H H
H H

L L W
W W L L

Dimensions
Case
Length Width Height A (Screw Mounts)

A10 0.91 in. 23.1 mm 0.63 in. 16 mm 0.79 in. 20.1 mm 0.67 in. 17 mm
A11 0.91 in. 23.1 mm 0.98 in. 24.9 mm 0.79 in. 20.1 mm 0.67 n. 17 mm

21
 High-Temp TOFD
Time-of-Flight Diffraction

The High-Temperature TOFD transducer acts like

a conventional TOFD transducer but designed for
temperatures up to 200°C (392°F). Time-of-flight
diffraction is a method used to determine the size
of mid-wall and I.D. cracks in metallic welds. It
requires highly-damped, broadband transducers,
and wedges that generate refracted longitudinal
(L) waves. The high-temp TOFD transducers come
standard with a straight-mounted Microdot
connector. The TOFD wedge is also designed for
use up to 200°C (392°F) and includes two couplant
irrigation ports and gimbal-mounting holes.

TRANSDUCERS
Frequency Number of Element Diameter SNI Part
Case (MHz) Elements in mm Number
2.25 16 0.250 6.40 00-015636
3/8 - 32
5 32 0.250 6.40 00-015635

WEDGES
Wedges
Case Style Temp Range Angle* Part Number
Up to 200°C 45°L 01-013467
3/8 - 32 Up to 200°C 60°L 01-013468
Up to 200°C 70°L 01-013469

W H
H W
L

Dimensions Dimensions
Case Wedge
Length Width Height Length Width Height

3/8 - 32 0.41 in. 10.4 mm 0.37 in. 9.5 mm 0.72 in. 18.3 mm 3/8 - 32 0.67 in. 17 mm 1.25 in. 31.8 mm 0.53 in. 13.5 mm

Gimbal-mounting holes: 5mm ø (0.2 in.) and 3mm deep (0.12 in.)
22
 High-Temp Corrosion Array
Dual-Linear Corrosion Array

The High-Temp Dual-Linear Corrosion Array is

optimized for corrosion and erosion inspection at
elevated temperatures. The transducer and its
replaceable delay line is designed to withstand
temperatures up to 200°C (395°F). This dual array
features 32 transmit and 32 receive elements to
provide larger beam coverage than conventionanl
dual-element transducers. The transmit and receive
element sets have an included angle to provide a
pseudo-focusing effect in the inspected material.
See page 12 for more ambient temperature
dual-linear corrosion array options.

TRANSDUCERS
Frequency Number of Element Pitch Elevation SNI Part
Case (MHz) Elements in mm in mm Number
CL 5 64 (32 x 2) 0.058 1.50 0.20 5 00-015634

Replaceable Delay

Celazole 01-014525

Sled

Stainless Steel 01-012570

W

Ha
Hb
Dimensions
Case
Length Width Height A Height B

CL 2.58 in. 65.5 mm 1.25 in. 31.8 mm 0.98 in. 24.9 mm 0.22 in. 5.6 mm L
CL w/ Sled 2.58 in. 65.5 mm 1.25 in. 31.8 mm 0.98 in. 24.9 mm 0.23 in. 5.8 mm
The sled features 3mm ø (0.12”) gimbal holes

DAC for #5 Flat Bottom Hole

5
Difference from Natural Focus

0
-5
-10
-15
-20
-25
High-Temp Dual Linear with
-30
optional sled attached.
0 0.05 0.075 0.1 0.2 0.3 0.4 0.5 0.75 1 1.25
Hole Depth (in.)
23
 CONVENTIONAL
TRANSDUCERS

CONTACT | DELAY-LINE | ANGLE BEAM |

IMMERSION | CO-POLYMER | DUAL ELEMENT |
HIGH-TEMP | THICKNESS GAUGING | CONTACT |
DELAY-LINE | ANGLE BEAM | IMMERSION |
CO-POLYMER | DUAL ELEMENT | HIGH-TEMP |
THICKNESS GAUGING | CONTACT | DELAY-LINE |
ANGLE BEAM | IMMERSION | CO-POLYMER |
DUAL ELEMENT | HIGH-TEMP | THICKNESS
GAUGING | CONTACT | DELAY-LINE | ANGLE
BEAM | IMMERSION | CO-POLYMER | DUAL
24
 Contact Transducers
CR

CONTACT CR
The larger element sizes of Model CR provide
greater scan widths and penetration for
applications such as plate, billet, bars, thick-section
parts, pipe, and tanks. They have side-mounted
BNC connectors and removable comfort grip to
reduce operator fatigue. GP series* offer the best
combination of sensitivity and resolution.

Single-Element Contacts are longitudinal-wave (straight-beam)

transducers designed for general purpose manual ultrasonic
inspection where test materials are relatively flat and smooth.
They provide high sensitivity for better penetration, small-flaw
detection, and have abrasion-resistant wear plates for
extended service life.

PART NUMBERS
Frequency Element Diameter Part Number
(MHz) inch mm GP Accessories
0.5 12.7 00-010626
1 0.75 19 00-010901
1 25.4 00-010902
0.5 12.7 00-010616
2.25 0.75 19 00-010419 Cable
1 25.4 00-010416 BNC - BNC
0.5 12.7 00-010903 6-ft (1.83 m)
3.5 0.75 19 00-010904 07-010018
1 25.4 00-010905
0.5 12.7 00-010617
5 0.75 19 00-010906
1 25.4 00-010907
10 0.5 12.7 00-010908

B
CASE DIMENSIONS
Element Ø
inch mm A B
A
0.50 12.7 1.5 in. 38.1 mm 1.3 in. 33 mm
0.75 19 1.75 in. 44.5 mm 1.3 in. 33 mm
1 25.4 2.0 in. 50.8 mm 1.4 in. 35.6 mm

* GP = General Purpose.
* See appendix for technical details. 25
 Contact Transducers
F Fingertip

CONTACT F FINGERTIP

Model F are small diameter transducers

with side-mounted Microdot connectors.
GP series* offer the best combination of
sensitivity and resolution for most
applications. HR series* are highly
damped for applications where high
resolution is required. C series* have
piezocomposite elements and offer superior
penetration in highly-attenuative materials.
All Model F transducers feature an ergonomic
design for improved operator control and comfort.

Single-Element Contacts are longitudinal-wave (straight-beam) transducers designed for

general purpose manual ultrasonic inspection where test materials are relatively flat and
smooth. They provide high sensitivity for better penetration, small-flaw detection, and have
abrasion-resistant wear plates for extended service life.

PART NUMBERS
Frequency Element Diameter Part Number
(MHz) inch mm GP HR C Accessories
0.25 6.4 00-010612 00-011084
2.25 0.375 9.5 00-010618 00-011085
0.5 12.7 00-010622 00-011086
0.25 6.4 00-010613 00-011087 Cable
3.5 0.375 9.5 00-010619 00-011088 MD - BNC
0.5 12.7 00-010623 00-011089 6-ft (1.83 m)
0.25 6.4 00-010614 00-010602 00-011090 07-010012
5 0.375 9.5 00-010620 00-010606 00-011091
0.5 12.7 00-010624 00-010610 00-011092
0.25 6.4 00-010615 00-010603
10
0.375 9.5 00-010621 00-010607

CASE DIMENSIONS B
Element Ø
inch mm A B
A
0.25 6.4 0.58 in. 14.7 mm 0.66 in. 16.8 mm
0.375 9.5 0.71 in. 18 mm 0.66 in. 16.8 mm
0.50 12.7 0.83 in. 21.1 mm 0.66 in. 16.8 mm

* GP = General Purpose; HR = High Resolution; C = Composite.

26 * See appendix for technical details.
 Delay-Line Contact
DFR

DFR FINGERTIP DELAY-LINE

Model DFR are small-diameter delay-line transducers with

side-mounted Microdot connectors. Removable delay lines and
highly damped piezoceramic elements enable measurement of very
thin parts or detection of small near-surface flaws. Delay lines can be
contoured for improved coupling to I.D. or O.D. curved parts. Custom
sizes and shapes also available upon request.

Delay-Line Contacts are single-element, longitudinal-wave

(straight beam) transducers designed for detection of near-surface
flaws and thickness measurement of thin-section materials.
Replaceable delay lines (stand-offs) improve near-surface
resolution and extend service life.

PART NUMBERS
Frequency Element Diameter Part Number Delay 10-PK Delay 10-PK
(MHz) inch mm HR L=.38 in (10mm) L=.5 in (12.7mm) Accessories
0.25 6.4 00-010940 01-010810 01-010811
2.25
0.5 12.7 00-012301 01-011971 01-011973
0.25 6.4 00-010824 01-010810 01-010811 Cable
3.5
0.5 12.7 00-010941 01-011971 01-011973 MD - BNC
0.25 6.4 00-010246 01-010810 01-010811 6-ft (1.83 m)
5
0.5 12.7 00-010492 01-011971 01-011973 07-010012
0.25 6.4 00-010247 01-010810 01-010811
10
0.5 12.7 00-012302 01-011971 01-011973
15 0.25 6.4 00-011077 01-010810 01-010811

Frequency Element Diameter Part Number Delay 10-PK

(MHz) inch mm HR L=.41 in (10.4mm) Accessories
Nominal
20MHz
0.125 3.2 00-012300 01-011974 See above B

CASE DIMENSIONS A
Element Ø B
inch mm A 0.38 in. Delay 0.5 in. Delay C
0.125 3.2 0.5 in. 12.7 mm 0.83 in. 21.1 mm 0.95 in. 24.1 mm 0.30 in. 7.6 mm
0.25 6.4 0.5 in. 12.7 mm 0.83 in. 21.1 mm 0.95 in. 24.1 mm 0.30 in. 7.6 mm
0.5 12.7 0.88 in. 22.4 mm 1.03 in. 26.2 mm 1.15 in. 29.2 mm 0.60 in. 15.2 mm
Mini-DFR
0.125 3.2 0.41 in. 10.4 mm 0.77 in. 19.6 mm 0.19 in. 4.8 mm

27
 Delay-Line Contact
Pencil Probes

Replaceable Delay-Line Pencil Probes

Pencil probes are designed for

applications requiring a very small
contact face, such as curved turbine
blades or thickness measurement from
the inside of a pit. They can be used with
most flaw detectors and precision thickness
gauges. Interchangeable delay lines are
tapered to tip diameters of 0.065 inch (1.7mm)
and 0.090 inch (2.3mm). Replaceable delay lines
are available in packs of 10. The straight model
features a removable handle, which also allows it
to be used as a fingertip probe. All models have
Microdot connectors.

Delay-Line Contacts are single-element, longitudinal-wave (straight beam)

transducers designed for detection of near-surface flaws and thickness measurement
of thin-section materials. Replaceable delay lines (stand-offs) improve near-surface
resolution and extend service life.

PART NUMBERS
Frequency Part Number
(MHz) Straight 45 Degree 90 Degree
7.5 00-011083 00-012296 00-012297
10 00-014008 00-014009 00-014010
15 00-011039 00-012298 00-012299

ACCESSORIES
Cable
F
Delay 10-PK Delay 10-PK Extension
.065" (1.7mm) Tip .090" (2.3mm) Tip MD - BNC Handle Knurled Ring
6-ft (1.83 m)
00-012222 00-012221 00-012220 06-014005
07-010012 A B
G
CASE DIMENSIONS
C
A B C D
1.0 in. 25.4 mm 0.60 in. 15.2 mm 0.42 in. 10.7 mm E

D E F G
0.4 in. 10.2 mm 0.09 in. 2.3 mm 4.0 in. 101.6 mm 0.42 in. 10.7 mm

28
 Delay-Line Contact
ZIP - Zero Interface Probes

Zero Interface Probes

Zero-Interface Probes (ZIP) are low-frequency

delay-line transducers designed to inspect composite
material. The special delay lines used are acoustically
matched to the composite material which allows for a
zero-interface signal, more efficient energy coupling &
transmission, and increased near-surface resolution.
Replaceable delay lines are available in packs of 5.

ZIP probes are special delay-line contact probes that are

single-element longitudinal-wave (straight beam)
transducers designed for the detection of near-surface flaws
and thickness measurement of thin cross-section materials.

PART NUMBERS
Frequency Element Diameter Part Number Delay 5-PK Delay 5-PK
(MHz) inch mm PN .375" (9.5mm) Tip .5" (12.7mm) Tip
0.5 1 25.4 00-012361 01-013488 01-013544
0.375 9.5 00-011173
1.5
0.5 12.7 00-012616

CASE DIMENSIONS A
Element Ø
inch mm A B C
0.375 9.5
B
1.40 in. 35.6 mm 0.46 in. 11.7 mm 0.75 in. 19.1 mm
0.5 12.7 1.14 in. 29 mm 0.63 in. 16 mm 0.87 in. 22.1 mm
1 25.4 1.70 in. 43.2 mm 1.04 in. 26.4 mm 1.45 in. 36.8 mm
C

Echo of a ZIP Delay Backwall Echo from a 0.14” (3.6mm)

Composite Component with ZIP 29
 Integral-Wedge Angle Beam
MWB+ & MWK+

MWB+ & MWK+ ANGLE BEAM

Models MWB+ and MWK+ are small transducers with side

or top-mounted Microdot connectors and integral wedges
for maximum versatility. GP series* (MWB+) offer the best
combination of sensitivity and resolution. C series* (MWK+)
with piezocomposite elements offer superior resolution,
penetration and signal-to-noise ratio in highly-attenuative
and coarse-grain materials such as austenitic stainless steel
or cast iron.

European-Style Angle-Beam Transducers generate shear

(transverse) waves at the specified angle in a given test material
to detect flaws that cannot be detected by a straight beam transducer.
Typical applications include weld inspection, tube and pipe, shafts, turbine
blades and wheel rims. Shear waves are produced by refracting a longitudinal
wave in a precision-machined acrylic wedge that also minimizes wedge noise.

PART NUMBERS
Frequency Element Dimensions Angle Connector Part Number
(MHz) inch mm (Steel) Location GP (MWB+) C (MWK+) Accessories
Top 00-012227 00-012306
35
Side 00-012226 00-012307
Top 00-012229 00-012308
45
Side 00-012228 00-012251 Cables
Top 00-012231 00-012309 MD - BNC
60
2 0.31 x 0.35 8x9 Side 00-012230 00-012252 Straight
Top 00-012233 00-012310 6-ft (1.83 m)
70
Side 00-012232 00-012253 07-010012
Top 00-012235 00-012311
80
Side 00-012234 00-012312 MCX - BNC
90 Side 00-012236 00-012313 Straight
Top 00-012238 00-012314 6-ft (1.83 m)
35
Side 00-012237 00-012315 07-010007
Top 00-012240 00-012316
45
Side 00-012239 00-012248 MCX - BNC
Top 00-012242 00-012317 Right Angle
60
4 0.31 x 0.35 8x9 Side 00-012241 00-012249 6-ft (1.83 m)
Top 00-012244 00-012318 07-010008 C
70
Side 00-012243 00-012250
Top 00-012246 00-012319
80
Side 00-012245 00-012320 B
90 Side 00-012247 00-012321

Element Dimensions
inch mm A B C A
0.31 x 0.35 8x9 1.07 in. 27.1 mm 0.86 in. 21.8 mm 0.66 in. 16.8 mm

30
 Small Angle Beam
Integral-Wedge Angle Beam
ABFP
MWB+ & MWK+ Dimensions

ABFP ANGLE BEAM

Model ABFP are small transducers with side Microdot

connectors and integral wedges for maximum versatility.
These small transducers are perfect for inspection in
hard to reach or restricted areas. C series* with
piezocomposite elements offer superior resolution,
penetration and signal-to-noise ratio. The piezocomposite
also heightens sensitivity and bandwidth.

Standard models listed below are designed for inspecting

carbon steel. These transducer can be designed to inspect other
materials as well as variations in inspection angle. ABFP come
standard with side-mounted microdot connectors but can be
special ordered with top-mounted connectors if requested.

PART NUMBERS
Frequency Element Size Part Number

(MHz) inch mm 45° 60° 70° 90° Accessories

0.187 x 0.187 4.75 x 4.75 00-013946 00-013947 00-013948 00-013949

2.25
0.25 x 0.25 6.4 x 6.4 00-013950 00-013951 00-013952 00-013953

0.187 x 0.187 4.75 x 4.75 00-013954 00-013955 00-013956 00-013957 Cable

5
0.25 x 0.25 6.4 x 6.4 00-013958 00-013959 00-013960 00-013961 MD - BNC

0.187 x 0.187 4.75 x 4.75 00-013962 00-013963 00-013964 00-013965 07-010012

10
0.25 x 0.25 6.4 x 6.4 00-013966 00-013967 00-013968 00-013969

CASE DIMENSIONS
Element Dimensions

inch mm A B C

0.187 x 0.187 4.75 x 4.75 0.70 in. 17.8 mm 0.32 in. 8.1 mm 0.50 in. 12.7 mm

0.25 x 0.25 6.4 x 6.4 1.0 in. 25.4 mm 0.50 in. 12.7 mm 0.50 in. 12.7 mm C

B A

* C = Composite. See appendix for technical details. 31

 Large Angle Beam
AWS & Wedges

AWS ANGLE-BEAM TRANSDUCERS

Model AWS transducers and wedges meet the requirements

of American Welding Society Structural Welding Code D1.1
and Bridge Welding Code D1.5. The transducers are
available with piezoceramic elements (GP series*) and
piezocomposite elements (C series*).

Angle-Beam Transducers and their wedges generate shear

(transverse) waves at the specified angle in a given test material
to detect flaws that cannot be detected by a straight beam
transducer. Typical applications include weld inspection, tube
and pipe, shafts, turbine blades and wheel rims. Shear waves are
produced by refracting a longitudinal wave in a precision machined
acrylic wedge that also minimizes wedge noise.

PART NUMBERS
Frequency Element Dimensions Part Number
(MHz) inch mm GP C Wedges Accessories
45° 01-010414 D
0.625 x 0.625 16 x 16 00-010393 00-010242 60° 01-010415
70° 01-010416 Cable
45° 01-010414 BNC - BNC C
2.25 0.625 x 0.75 16 x 19 00-010395 00-010394 60° 01-010415 6-ft (1.83 m)
70° 01-010416 07-010018
45° 01-010414
A B
0.75 x 0.75 19 x 19 00-010397 00-010396 60° 01-010415
70° 01-010416

CASE DIMENSIONS
Element Dimensions
inch mm A B C D Thread
0.625 x 0.625 16 x 16 0.80 in. 20.3 mm 1.26 in. 32 mm 0.75 in. 19.1 mm 1.0 in. 25.4 mm
0.625 x 0.75 16 x 19 0.80 in. 20.3 mm 1.26 in. 32 mm 0.75 in. 19.1 mm 1.0 in. 25.4 mm 4-40
0.75 x 0.75 19 x 19 0.85 in. 21.6 mm 1.26 in. 32 mm 0.75 in. 19.1 mm 1.0 in. 25.4 mm

AWS WEDGE DIMENSIONS

H
Part Wedge Dimensions
Wedge Type Number Length Width Height
45° 01-010414 1.82 in. 46.2 mm 1.25 in. 31.8 mm 1.91 in. 48.5 mm W
60° 01-010415 1.96 in. 49.8 mm 1.25 in. 31.8 mm 1.91 in. 48.5 mm

70° 01-010416 2.17 in. 55.1 mm 1.25 in. 31.8 mm 2.16 in. 54.9 mm
L
32 * C = Composite; GP = General Purpose. See appendix for technical details.
 Large Angle Beam
SWS

SWS ANGLE BEAM

Model SWS are designed for general weld inspection and other applications
such as pipes, tanks, pressure vessels, forgings and castings. They have top
mounted BNC connectors and are available with piezocomposite elements
(C series*). Interchangeable acrylic wedges provide maximum versatility
and service life.

Angle-Beam Transducers and their wedges generate shear (transverse) waves at the specified angle in a given test
material to detect flaws that cannot be detected by a straight-beam transducer. Typical applications include weld
inspection, tube and pipe, shafts, turbine blades and wheel rims. Shear waves are produced by refracting a
longitudinal wave in a precision machined acrylic wedge that also minimizes wedge noise.

PART NUMBERS
Frequency Element Dimensions Frequency Element Dimensions
(MHz) inch mm C Wedges Accessories (MHz) inch mm C Wedges Accessories
45° 01-010417 45° 01-010417
0.5 Ø 12.7 Ø 00-010478 60° 01-010418 0.5 Ø 12.7 Ø 00-010449 60° 01-010418
70° 01-010419 70° 01-010419
45° 01-010425 45° 01-010425
0.5 x 1 12.7 x 25.4 00-010479 60° 01-010426 0.5 x 1 12.7 x 25.4 00-010450 60° 01-010426
70° 01-010427 70° 01-010427
0.5 2.25
45° 01-010428 45° 01-010428
0.75 x 1 19 x 25.4 00-010480 60° 01-010429 0.75 x 1 19 x 25.4 00-010451 60° 01-010429

70° 01-010430 70° 01-010430

45° 01-010991 Cable 45° 01-010991 Cable

1Ø 25.4 Ø 1Ø 25.4 Ø 00-010452 60° 01-010992 BNC - BNC

00-010481 60° 01-010992 BNC - BNC
70° 01-010993 6-ft (1.83 m)
70° 01-010993 6-ft (1.83 m)
45° 01-010417 07-010018
45° 01-010417 07-010018
0.5 Ø 12.7 Ø 00-010453 60° 01-010418
0.5 Ø 12.7 Ø 00-010445 60° 01-010418
70° 01-010419
70° 01-010419
45° 01-010425
45° 01-010425
0.5 x 1 12.7 x 25.4 00-010454 60° 01-010426
0.5 x 1 12.7 x 25.4 00-010446 60° 01-010426
70° 01-010427
70° 01-010427 3.5
1 45° 01-010428
45° 01-010428
0.75 x 1 19 x 25.4 00-010455 60° 01-010429
0.75 x 1 19 x 25.4 00-010447 60° 01-010429
70° 01-010430
70° 01-010430
45° 01-010991
45° 01-010991
1Ø 25.4 Ø 00-010456 60° 01-010992
1Ø 25.4 Ø 00-010448 60° 01-010992
70° 01-010993
70° 01-010993
45° 01-010417
* C = Composite. See appendix for technical details. 0.5 Ø 12.7 Ø 00-010457 60° 01-010418
70° 01-010419
45° 01-010425
0.5 x 1 12.7 x 25.4 00-010458 60° 01-010426
70° 01-010427
5
45° 01-010428
0.75 x 1 19 x 25.4 00-010459 60° 01-010429
70° 01-010430
45° 01-010991
1Ø 25.4 Ø 00-010460 60° 01-010992
70° 01-010993
33
 Large Angle Beam
SWS

SWS CASE DIMENSIONS

Element Size
inch mm A B C D
0.5 Ø 12.7 Ø 0.72 in. 18.3 mm 1.0 in. 25.4 mm 0.75 in. 19 mm 0.81 in. 20.6 mm
0.5 x 1 12.7 x 25.4 0.73 in. 18.5 mm 1.5 in. 38.1 mm 0.75 in. 19 mm 1.31 in. 33.3 mm
0.75 x 1 19 x 25.4 1.0 in. 25.4 mm 1.5 in. 38.1 mm 0.75 in. 19 mm 1.31 in. 33.3 mm
1Ø 25.4 Ø 1.22 in. 31.0 mm 1.65 in. 41.9 mm 0.75 in. 19 mm 1.38 in. 35.1 mm
Thread
4-40

A B

SWS WEDGE DIMENSIONS

Part Wedge Dimensions

Wedge Type Number Length Width Height
SWS 01-010417 1.35 in. 34.3 mm 1.1 in. 30 mm 1.3 in. 33 mm

SWS 01-010418 1.53 in. 38.9 mm 1.1 in. 30 mm 1.3 in. 33 mm

SWS 01-010419 1.82 in. 46.2 mm 1.1 in. 30 mm 1.3 in. 33 mm

SWS 01-010425 1.35 in. 34.3 mm 1.6 in. 40.6 mm 1.3 in. 33 mm

SWS 01-010426 1.53 in. 38.9 mm 1.6 in. 40.6 mm 1.3 in. 33 mm H
SWS 01-010427 1.82 in. 46.2 mm 1.6 in. 40.6 mm 1.3 in. 33 mm

SWS 01-010428 2.1 in. 53.3 mm 1.5 in. 38.1 mm 1.5 in. 38.1 mm

SWS 01-010429 2.3 in. 48.4 mm 1.5 in. 38.1 mm 1.5 in. 38.1 mm

W
SWS 01-010430 2.59 in. 65.8 mm 1.5 in. 38.1 mm 1.5 in. 38.1 mm

SWS 01-010991 2.05 in. 52.1 mm 1.65 in. 41.9 mm 1.5 in. 38.1 mm L
SWS 01-010992 2.24 in. 56.9 mm 1.65 in. 41.9 mm 1.5 in. 38.1 mm

SWS 01-010993 2.6 in. 66 mm 1.65 in. 41.9 mm 1.5 in. 38.1 mm

SWS 01-012357 1.9 in. 48.3 mm 1.5 in. 38.1 mm 1.5 in. 38.1 mm

SWS 01-012759 1.35 in. 34.3 mm 1.1 in. 30 mm 1.3 in. 33 mm

SWS 01-012760 1.35 in. 34.3 mm 1.6 in. 40.6 mm 1.3 in. 33 mm

SWS 01-012761 2.36 in. 60 mm 1.65 in. 41.9 mm 1.5 in. 38.1 mm

34
 Small Angle Beam
MSWS

MSWS ANGLE-BEAM TRANSDUCERS

Model MSWS have captive screws for wedge attachment and angled Microdot
connectors for applications requiring low profile. Piezocomposite (C series*)
offer superior penetration and signal-to-noise ratio in highly-attenuative and
coarse-grain materials.

Angle-Beam Transducers and their wedges, generate shear

(transverse) waves at the specified angle in a given test material to
detect flaws that cannot be detected by a straight-beam transducer.
Typical applications include weld inspection, tube and pipe, shafts,
turbine blades and wheel rims. Shear waves are produced by
refracting a longitudinal wave in a precision machined acrylic wedge
that also minimizes wedge noise.

Frequency Element Diameter

(MHz) inch mm C Wedges Accessories
45° 01-012776
1 0.5 12.7 00-010497 60° 01-012777
70° 01-012778
45° 01-012773
0.25 6.4 00-010498 60° 01-012774
70° 01-012775
2.25
45° 01-012776
0.5 12.7 00-010499 60° 01-012777
70° 01-012778
45° 01-012773
0.25 6.4 00-010500 60° 01-012774
70° 01-012775 Cable
3.5
45° 01-012776 MD - BNC
0.5 12.7 00-010501 60° 01-012777 6-ft (1.83 m)
70° 01-012778 07-010012
45° 01-012773
0.25 6.4 00-010502 60° 01-012774
70° 01-012775
5
45° 01-012776
0.5 12.7 00-010503 60° 01-012777
70° 01-012778
45° 01-012773
0.25 6.4 00-010504 60° 01-012774
70° 01-012775
10
45° 01-012776
0.5 12.7 00-010505 60° 01-012777
70° 01-012778
* C = Composite. See appendix for technical details.
35
 Small Angle Beam
MSWS

CASE DIMENSIONS
Element Ø
inch mm A B C D Thread
* C = Composite. See appendix for technical details.
0.25 6.4 0.48 in. 12.2 mm 0.34 in. 8.6 mm 0.31 in. 7.9 mm 0.38 in. 9.7 mm
1-64
0.5 12.7 0.73 in. 18.5 mm 0.5 in. 12.7 mm 0.56 in. 14.2 mm 0.63 in. 16 mm

D
C

MSWS WEDGE DIMENSIONS

Part Wedge Dimensions

ype Number Length Width Height
01-012773 0.59 in. 15 mm 0.5 in. 12.7 mm 0.26 in. 6.6 mm

01-012774 0.65 in. 16.5 mm 0.5 in. 12.7 mm 0.30 in. 7.6 mm

01-012775 0.73 in. 18.5 mm 0.5 in. 12.7 mm 0.33 in. 8.4 mm

01-012776 0.93 in. 23.6 mm 0.75 in. 19 mm 0.43 in. 10.9 mm

01-012777 1.05 in. 26.7 mm 0.75 in. 19 mm 0.50 in. 12.7 mm

01-012778 1.18 in. 30 mm 0.75 in. 19 mm 0.54 in. 13.7 mm

L W

36
 Small Angle Beam
TOFD
MWB+3/8-32
& MWK+& 11/16-24
Dimensions

TOFD ANGLE BEAM

Time-Of-Flight Diffraction (TOFD) is a method used to

determine the size of cracks in metallic welds. It requires
highly-damped, broadband transducers and wedges that
generate refracted longitudinal waves (L-waves). SNI's
TOFD transducers have state-of-the-art piezocomposite
elements (C series*) and Quick Swap screw-in wedge
attachment. Straight-mounted connectors are Microdot
& MCX (3/8-32 & 11/16-24) or Lemo-00 (M12 case).

3/8-32 (ST1) PART NUMBERS 11/16-24 (ST2) PART NUMBERS

Frequency Element Diameter Part Number Frequency Element Diameter Part Number
(MHz) inch mm Connector C Connector C Accessories (MHz) inch mm Connector C Connector C Accessories

2.25 0.25 6 Microdot 00-010493 MCX 00-011277 0.375 9.5 Microdot 00-013977 MCX 00-013017

2.25

0.125 3 Microdot 00-010168 MCX 00-010164 0.5 12.7 Microdot 00-013008 MCX 00-013018 Cables
MD - BNC
5
6-ft (1.83 m)
0.25 6 Microdot 00-010398 MCX 00-011276 0.375 9.5 Microdot 00-013021 MCX 00-013022 07-010012

0.125 3 Microdot 00-010167 MCX 00-010163 0.5 12.7 Microdot 00-013019 MCX 00-013020

Cables
7.5
MD - BNC See page 38 for TOFD wedges
0.25 6 Microdot 00-010748 MCX 00-011280 6-ft (1.83 m)
07-010012
11/16”-24 DIMENSIONS
0.125 3 Microdot 00-010166 MCX 00-010162
Element Dimensions
10 inch mm A B C
0.375 9.5 0.62 in. 15.8 mm 0.68 in. 17.3 mm 0.70 in. 17.8 mm
0.25 6 Microdot 00-010387 MCX 00-011278
0.5 12.7 0.62 in. 15.8 mm 0.68 in. 17.3 mm 0.70 in. 17.8 mm

0.125 3 Microdot 00-010165 MCX 00-010161 B

15

0.25 6 Microdot 00-010749 MCX 00-011281

A C
See page 38 for TOFD wedges

3/8”-32 DIMENSIONS
Element Dimensions B
inch mm A B C
0.125 3 0.37 in. 9.4 mm 0.72 in. 18.3 mm 0.41 in. 10.4 mm
0.25 6 0.37 in. 9.4 mm 0.72 in. 18.3 mm 0.41 in. 10.4 mm

A
C

* C = Composite. See appendix for technical details. 37

 Small Angle Beam
TOFD
MWB+M12
& MWK+ Dimensions

M12 PART NUMBERS

Frequency Element Diameter Part Number
(MHz) inch mm Connector C Accessories

2.25 0.25 6 Lemo-00 00-011897

0.125 3 Lemo-00 00-010299

0.25 6 Lemo-00 00-010300

Cables
Lemo-00 - BNC
0.125 3 Lemo-00 00-010298 6-ft (1.83 m)
07-010014
10

0.25 6 Lemo-00 00-010386

0.125 3 Lemo-00 00-010631

15

0.25 6 Lemo-00 00-013016

See page 38 for TOFD wedges

M12 DIMENSIONS
Element Dimensions
inch mm A B
B
0.125 3 0.37 in. 9.4 mm 0.72 in. 18.3 mm
0.25 6 0.37 in. 9.4 mm 0.72 in. 18.3 mm

38
 Small Angle Beam
TOFD
MWB+Wedges
& MWK+ Dimensions

3/8-32 WEDGES 3/8-32 WEDGE SIZING

Angle Thread Additional Info Part Number L W H Diagram Reference
45° L 3/8 - 32 Single Port with Adjustable Wear Pins 01-010666 1.06 in. 27 mm 1.0 in. 25.4 mm 0.52 in. 13.2 mm
60° L 3/8 - 32 Single Port with Adjustable Wear Pins 01-010667 1.06 in. 27 mm 1.0 in. 25.4 mm 0.52 in. 13.2 mm 1
70° L 3/8 - 32 Single Port with Adjustable Wear Pins 01-010668 1.06 in. 27 mm 1.0 in. 25.4 mm 0.52 in. 13.2 mm
45° L 3/8 - 32 01-011597 0.83 in. 21.1 mm 1.25 in. 31.8 mm 0.50 in. 12.7 mm
60° L 3/8 - 32 01-011598 0.83 in. 21.1 mm 1.25 in. 31.8 mm 0.50 in. 12.7 mm 2
70° L 3/8 - 32 01-011599 0.83 in. 21.1 mm 1.25 in. 31.8 mm 0.50 in. 12.7 mm
45° L 3/8 - 32 Dual Ports with Adjustable Wear Pins 01-012235 0.83 in. 21.1 mm 1.25 in. 31.8 mm 0.50 in. 12.7 mm
60° L 3/8 - 32 Dual Ports with Adjustable Wear Pins 01-012236 0.83 in. 21.1 mm 1.25 in. 31.8 mm 0.50 in. 12.7 mm
70° L 3/8 - 32 Dual Ports with Adjustable Wear Pins 01-012237 0.83 in. 21.1 mm 1.25 in. 31.8 mm 0.50 in. 12.7 mm
3
45° L 3/8 - 32 Dual Ports, Stainless Steel Housing 01-012264 0.67 in. 17 mm 1.25 in. 31.8 mm 0.53 in. 13.5 mm
60° L 3/8 - 32 Dual Ports, Stainless Steel Housing 01-012263 0.67 in. 17 mm 1.25 in. 31.8 mm 0.53 in. 13.5 mm
70° L 3/8 - 32 Dual Ports, Stainless Steel Housing 01-011993 0.67 in. 17 mm 1.25 in. 31.8 mm 0.53 in. 13.5 mm

11/16-24 WEDGES 11/16-24 WEDGE SIZING

Angle Thread Additional Info Part Number L W H Diagram Reference
45° L 11/16 - 24 01-011594 1.0 in. 25.4 mm 1.25 in. 31.8 mm 0.63 in. 16 mm
60° L 11/16 - 24 01-010595 1.0 in. 25.4 mm 1.25 in. 31.8 mm 0.63 in. 16 mm 2
70° L 11/16 - 24 01-011596 1.0 in. 25.4 mm 1.25 in. 31.8 mm 0.63 in. 16 mm
45° L 11/16 - 24 Dual Ports with Adjustable Wear Pins 01-012269 1.0 in. 25.4 mm 1.25 in. 31.8 mm 0.63 in. 16 mm
60° L 11/16 - 24 Dual Ports with Adjustable Wear Pins 01-012270 1.0 in. 25.4 mm 1.25 in. 31.8 mm 0.63 in. 16 mm 3
70° L 11/16 - 24 Dual Ports with Adjustable Wear Pins 01-012271 1.0 in. 25.4 mm 1.25 in. 31.8 mm 0.63 in. 16 mm

M12 WEDGES M12 WEDGE SIZING

Angle Thread Additional Info Part Number L W H Diagram Reference
45° L M12 Carbon Steel, 7.1mm Delay, Dual Ported 01-010334 0.79 in. 20.1 mm 1.18 in. 30 mm 0.57 in. 14.5 mm
60° L M12 Carbon Steel, 7.1mm Delay, Dual Ported 01-010335 0.79 in. 20.1 mm 1.18 in. 30 mm 0.57 in. 14.5 mm 4
70° L M12 Carbon Steel, 7.0mm Delay, Dual Ported 01-010336 0.79 in. 20.1 mm 1.18 in. 30 mm 0.57 in. 14.5 mm

1 2
L
W
H
H
W
L
L

3 4

H
H
W
W
L
L 39
 Small Angle Beam
QS

PART NUMBERS QS ANGLE-BEAM TRANSDUCERS

Frequency Element Diameter
Model QS features Quick Swap screw-in wedge attachment.
(MHz) inch mm C** Accessories
They are available with top-mounted Microdot (MD) or new MCX
low-profile swivel connectors. Piezocomposite (C series*) offer
0.375 9.5
00-010137 superior penetration and signal-to-noise ratio in highly-
MD or MCX
attenuative and coarse-grain materials.
1

00-010138
0.5 12.7
MD or MCX
Angle-Beam Transducers and their wedges, generate shear
(transverse) waves at the specified angle in a given test material
to detect flaws that cannot be detected by a straight-beam
transducer. Typical applications include weld inspection, tube
00-010216
0.25 6.4
MD or MCX
and pipe, shafts, turbine blades and wheel rims. Shear waves are
Cables
produced by refracting a longitudinal wave in a
precision-machined acrylic wedge that also minimizes wedge
MD - BNC
noise.
00-010217 6-ft (1.83 m)
1.5 0.375 9.5
MD or MCX 07-010012

MCX - BNC
00-010218 Straight
0.5 12.7
MD or MCX 6-ft (1.83 m)
07-010007

00-010122 MCX - BNC

0.25 6.4
MD or MCX Right Angle
6-ft (1.83 m)
07-010008
00-010123
2.25 0.375 9.5
MD or MCX

00-010124
0.5 12.7
MD or MCX

Chart continues on page 41

* C = Composite. See appendix for technical details.

** When ordering QS transducers, please include the part number
40 followed by the connector type (MD or MCX)
 Small Angle Beam
QS & QS Wedges

PART NUMBERS CONTINUED CASE DIMENSIONS

Frequency Element Diameter Element Ø
(MHz) inch mm C** Accessories inch mm A B C
0.25 6.4 3/8 - 32 UNEF 0.58 in. 14.7 mm 0.43 in. 10.9 mm
0.375 9.5 1/2 - 28 UNEF 0.58 in. 14.7 mm 0.54 in. 13.7 mm
00-010125
0.25 6.4 0.5 12.7 5/8 - 24 UNEF 0.65 in. 16.5 mm 0.69 in. 17.5 mm
MD or MCX

3.5 0.375 9.5

00-010126 B
MD or MCX

00-010127
0.5 12.7
MD or MCX A
C
00-010128
0.25 6.4
MD or MCX

00-010129
QS STANDARD WEDGES
5 0.375 9.5
MD or MCX Cables

Element Diameter Standard Wedges

MD - BNC inch mm Angle Carbon Steel Stainless Steel Aluminum
00-010130 6-ft (1.83 m) 30° 01-012100
0.5 12.7
MD or MCX 07-010012 45° 01-012101 01-010636 01-010840
0.25 6.4
60° 01-012102 01-010637 01-010841
70° 01-012103 01-010638 01-010842
00-010131 MCX - BNC
0.25 6.4 30° 01-012104
MD or MCX Right Angle
45° 01-012105 01-010640 01-010713
6-ft (1.83 m) 0.375 9.5
60° 01-012106 01-010641 01-010838
07-010008
70° 01-012107 01-010642 01-010839
00-010132
7.5 0.375 9.5 30° 01-012108
MD or MCX
45° 01-012109 01-010644 01-010527
0.5 12.7
60° 01-012110 01-010645 01-010528
70° 01-012111 01-010646 01-010529
00-010133
0.5 12.7
MD or MCX

QS SHORT INDEX WEDGES

00-010134
0.25 6.4
MD or MCX Element Diameter Short Index Wedges
inch mm Angle Carbon Steel Stainless Steel Aluminum
45° 01-012116 01-012128 01-010480
00-010135 0.25 6.4 60° 01-012117 01-012129 01-010481
10 0.375 9.5
MD or MCX 70° 01-012118 01-012130 01-010482
45° 01-012120 01-012132 01-010484
0.375 9.5 60° 01-012121 01-012133 01-010485
00-010136 70° 01-012122 01-012134 01-010486
0.5 12.7
MD or MCX 45° 01-012124 01-012136 01-010488
0.5 12.7 60° 01-012125 01-012137 01-010489
70° 01-012126 01-012138 01-010490

** When ordering QS transducers, please include the part number

followed by the connector type (MD or MCX) 41
 Small Angle Beam
QS Wedge Dimensions

QS STANDARD WEDGE DIMENSIONS

Part Wedge Dimensions Part Wedge Dimensions
Wedge Type Number Length Width Height Wedge Type Number Length Width Height
Carbon Steel 01-012100 0.70 in. 17.78 mm 0.45 in. 11.4 mm 0.37 in. 9.4 mm Stainless Steel 01-010636 0.75 in. 19 mm 0.45 in. 11.4 mm 0.43 in. 10.9 mm
Carbon Steel 01-012101 0.75 in. 19 mm 0.45 in. 11.4 mm 0.39 in. 9.9 mm Stainless Steel 01-010637 0.84 in. 21.3 mm 0.45 in. 11.4 mm 0.47 in. 11.9 mm
Carbon Steel 01-012102 0.84 in. 21.3 mm 0.45 in. 11.4 mm 0.44 in. 11.2 mm Stainless Steel 01-010638 1.0 in. 25.4 mm 0.45 in. 11.4 mm 0.52 in. 13.2 mm
Carbon Steel 01-012103 1.0 in. 25.4 mm 0.45 in. 11.4 mm 0.50 in. 12.7 mm Stainless Steel 01-010640 0.89 in. 22.6 mm 0.55 in. 14 mm 0.51 in. 13 mm
Carbon Steel 01-012104 0.83 in. 21.1 mm 0.55 in. 14 mm 0.47 in. 11.9 mm Stainless Steel 01-010641 1.04 in. 26.4 mm 0.55 in. 14 mm 0.56 in. 14.2 mm
Carbon Steel 01-012105 0.89 in. 22.6 mm 0.55 in. 14 mm 0.47 in. 11.9 mm Stainless Steel 01-010642 1.19 in. 30.2 mm 0.55 in. 14 mm 0.61 in. 15.5 mm
Carbon Steel 01-012106 1.04 in. 26.4 mm 0.55 in. 14 mm 0.55 in. 14 mm Stainless Steel 01-010644 1.05 in. 26.7 mm 0.70 in. 17.8 mm 0.63 in. 16 mm
Carbon Steel 01-012107 1.19 in. 30.2 mm 0.55 in. 14 mm 0.58 in. 14.7 mm Stainless Steel 01-010645 1.24 in. 31.5 mm 0.70 in. 17.8 mm 0.67 in. 17 mm
Carbon Steel 01-012108 0.98 in. 24.9 mm 0.70 in. 17.8 mm 0.55 in. 14 mm Stainless Steel 01-010646 1.41 in. 35.8 mm 0.70 in. 17.8 mm 0.71 in. 18 mm
Carbon Steel 01-012109 1.05 in. 26.7 mm 0.70 in. 17.8 mm 0.55 in. 14 mm
Carbon Steel 01-012110 1.24 in. 31.5 mm 0.70 in. 17.8 mm 0.64 in. 16.3 mm Part Wedge Dimensions
Carbon Steel 01-012111 1.41 in. 35.8 mm 0.70 in. 17.8 mm 0.68 in. 17.3 mm Wedge Type Number Length Width Height
Aluminum 01-010840 0.75 in. 19 mm 0.45 in. 11.4 mm 0.43 in. 10.9 mm
Aluminum 01-010841 0.84 in. 21.3 mm 0.45 in. 11.4 mm 0.47 in. 11.9 mm
Aluminum 01-010842 1.0 in. 25.4 mm 0.45 in. 11.4 mm 0.52 in. 13.2 mm
Aluminum 01-010713 0.89 in. 22.6 mm 0.55 in. 14 mm 0.51 in. 13 mm
Aluminum 01-010838 1.04 in. 26.4 mm 0.55 in. 14 mm 0.56 in. 14.2 mm

H Aluminum
Aluminum
01-010839
01-010527
1.19 in.
1.05 in.
30.2 mm
26.7 mm
0.55 in.
0.70 in.
14 mm
17.8 mm
0.61 in.
0.63 in.
15.5 mm
16 mm
Aluminum 01-010528 1.24 in. 31.5 mm 0.70 in. 17.8 mm 0.67 in. 17 mm
Aluminum 01-010529 1.41 in. 35.8 mm 0.70 in. 17.8 mm 0.71 in. 18 mm
W
L

QS SHORT INDEX WEDGE DIMENSIONS

Part Short Index Wedge Dimensions Part Short Index Wedge Dimensions
Wedge Type Number Length Width Height Wedge Type Number Length Width Height
Carbon Steel 01-012116 0.62 in. 15.7 mm 0.45 in. 11.4 mm 0.39 in. 9.9 mm Stainless Steel 01-012128 0.62 in. 15.7 mm 0.45 in. 11.4 mm 0.39 in. 9.9 mm
Carbon Steel 01-012117 0.75 in. 19 mm 0.45 in. 11.4 mm 0.45 in. 11.4 mm Stainless Steel 01-012129 0.75 in. 19 mm 0.45 in. 11.4 mm 0.47 in. 11.9 mm
Carbon Steel 01-012118 0.80 in. 20.3 mm 0.45 in. 11.4 mm 0.50 in. 12.7 mm Stainless Steel 01-012130 0.80 in. 20.3 mm 0.45 in. 11.4 mm 0.50 in. 12.7 mm
Carbon Steel 01-012120 0.78 in. 19.8 mm 0.55 in. 14 mm 0.47 in. 11.9 mm Stainless Steel 01-012132 0.78 in. 19.8 mm 0.55 in. 14 mm 0.47 in. 11.9 mm
Carbon Steel 01-012121 0.85 in. 21.6 mm 0.55 in. 14 mm 0.55 in. 14 mm Stainless Steel 01-012133 0.85 in. 21.6 mm 0.55 in. 14 mm 0.55 in. 14 mm
Carbon Steel 01-012122 0.97 in. 24.6 mm 0.55 in. 14 mm 0.57 in. 14.5 mm Stainless Steel 01-012134 1.02 in. 25.9 mm 0.55 in, 14 mm 0.59 in. 15 mm
Carbon Steel 01-012124 0.90 in. 22.9 mm 0.70 in. 17.8 mm 0.55 in. 14 mm Stainless Steel 01-012136 0.90 in. 22.9 mm 0.70 in. 17.8 mm 0.55 in. 14 mm
Carbon Steel 01-012125 1.06 in. 26.9 mm 0.70 in. 17.8 mm 0.64 in. 16.3 mm Stainless Steel 01-012137 1.06 in. 26.9 mm 0.70 in. 17.8 mm 0.64 in. 16.3 mm
Carbon Steel 01-012126 1.17 in. 29.7 mm 0.70 in. 17.8 mm 0.70 in. 17.8 mm Stainless Steel 01-012138 1.17 in. 29.7 mm 0.70 in. 17.8 mm 0.67 in. 17 mm

Part Short Index Wedge Dimensions

Wedge Type Number Length Width Height
Aluminum 01-010480 0.62 in. 15.7 mm 0.45 in. 11.4 mm 0.39 in. 9.9 mm
Aluminum 01-010481 0.75 in. 19 mm 0.45 in. 11.4 mm 0.47 in. 11.9 mm
Aluminum 01-010482 0.80 in. 20.3 mm 0.45 in. 11.4 mm 0.50 in. 12.7 mm
Aluminum 01-010484 0.78 in. 19.8 mm 0.55 in. 14 mm 0.47 in. 11.9 mm

H Aluminum 01-010485 0.85 in. 21.6 mm 0.55 in. 14 mm 0.55 in. 14 mm

Aluminum 01-010486 1.02 in. 25.9 mm 0.55 in, 14 mm 0.59 in. 15 mm
Aluminum 01-010488 0.90 in. 22.9 mm 0.70 in. 17.8 mm 0.55 in. 14 mm
Aluminum 01-010489 1.06 in. 26.9 mm 0.70 in. 17.8 mm 0.64 in. 16.3 mm
W
L Aluminum 01-010490 1.17 in. 29.7 mm 0.70 in. 17.8 mm 0.67 in. 17 mm

42
 Immersion Transducers
Immersion Transducers are typically used in automatic and manual scanning systems using water or other
liquid as a coupling medium to enable the inspection of parts with complex geometries and with
near-surface resolution superior to that of contact transducers. Spherical (point) or cylindrical (line)
focusing can further improve sensitivity and resolution. Focal length must be specified.

Please choose your Part number from the following charts based on Case Type,
Element Ø (Inches) Transducer Frequency and Element Diameter. The Part Number on the charts
Frequency
specifies these attributes.
(Mhz)
1 0.75 0.5 0.375 0.25
To Specify the Focal Length (in inches) and Focal Type (Spherical or Cylindrical)
Near 4.3 2.4 1.1 you desire: Edit the X.X S and Y.YC suffixes shown in the chart to match your
1 Min 2.0 1.5 0.75
2 requirements.
Max 2.75 1.75 0.75 2
(ex. The suffix for a 2.0” Spherical focus is changed from X.XS to 2.0S;
Near 9.6 5.4 2.4 1.4 0.6 The suffix for a 3.0” Cylindrical Focus is changed from Y.YC to 3.0C)
2.25 Min 2.0 1.5 1.0 0.75 0.375 2,3
2,3
Max 6.0 3.5 1.5 1.0 0.375 NF = Non-focused (flat)
Near 15.0 8.4 3.7 2.1 0.9 S = Spherical focus
0.375
3 C = Cylindrical focus
3.5 Min 2.0 1.5 1.0 0.75
Max 8.0 5.5 2.25 1.25 0.5
Near = Nearfield Length in water
Near 21.0 12.0 5.4 3.0 1.3
Min = Minimum recommended focal length in water
5 Min 2.0 1.5 1.0 0.75 0.5 Max= Maximum recommended focal length in water
1
Max 8.0 7.5 3.5 2.0 0.75
All focal lengths are listed in inches of water from the reflection off a flat
Near 24.0 10.7 6.0 2.7 stainless steel reflector. Divide by 4 for the approximate distance in steel.
10 Min 1.5 1.0 0.75 0.5
Focal lengths are offered in 0.25” increments between the Min and Max
Max 8.0 1 6.0 4.0 1.5
listed. Focal lengths outside the recommended limits can be ordered,
Near 16.0 9.0 4.0 but on a best effort basis only.
15 Min 1.0 0.75 0.5
1
1
Achievable focal lengths of these models are shorter compared to their
Max 6.0 5.0 2.0 nearfield length due to attenuation and other effects at long water paths.
Longer focal lengths can be ordered, but on a best effort basis.
2
Max and Min focal lengths are the same for these models due to the
physics and geometry of this combination.
3
A focal length other than the normal 0.25” increment is offered in this
combination.

Please confirm your focal length in your applications: Use of probes with
F-Numbers under 4.0 (near the minimum focal length listed on this chart)
can introduce other wave modes and/or be less effective since acoustic
energy at the edge of the beam may be at relatively high incident angles.
F-Number = Focal Length/Element Diameter.
(Example: 2.0” Focus probe with 0.375” element = 2.0”/0.375” =
F-Number = 5.3) 43
 Immersion Transducers
I1

I1 IMMERSION

Model I1 are small-diameter, pencil-type transducers with

straight-mounted Microdot connectors. Because the
connectors are not waterproof, sealing with non-water-soluble
grease is recommended. GP series* offer the best combination
of sensitivity and resolution for general applications. HR series*
are highly damped for applications where high resolution is
required. C series* have piezocomposite elements and offer
superior penetration, resolution and signal-to-noise ratio in
highly-attenuative and coarse-grain materials.

Immersion Transducers are typically used in automated and manual-scanning systems

using water or other liquid as a coupling medium. This enables the inspection of parts with
complex geometries and near-surface resolution superior to that of contact transducers.
Spherical (point) or cylindrical (line) focusing can further improve sensitivity and resolution.
Focal length and focal type must be specified.

PART NUMBERS
Frequency Element Diameter Part Number
(MHz) inch mm Focus GP HR C Accessories
None 00-011300 NF 00-011301 NF 00-011302 NF
2.25 0.25 6.4 Spherical 00-011300 X.XS 00-011301 X.XS 00-011302 X.XS
Cylindrical 00-011300 Y.YC 00-011301 Y.YC 00-011302 Y.YC
None 00-011303 NF 00-010593 NF 00-010711 NF
5 0.25 6.4 Spherical 00-011303 X.XS 00-010593 X.XS 00-010711 X.XS Cable
Cylindrical 00-011303 Y.YC 00-010593 Y.YC 00-010711 Y.YC MD - BNC
None 00-010822 NF 00-010377 NF 00-010823 NF 6-ft (1.83 m)
10 0.25 6.4 Spherical 00-010822 X.XS 00-010377 X.XS 00-010823 X.XS 07-010012
Cylindrical 00-010822 Y.YC 00-010377 Y.YC 00-010823 Y.YC
None 00-010596 NF 00-011304 NF
15 0.25 6.4 Spherical 00-010596 X.XS 00-011304 X.XS
Cylindrical 00-010596 Y.YC 00-011304 Y.YC

CASE DIMENSIONS
Element Ø
inch mm A B B
0.25 6.4 0.38 in. 9.7 mm 1.25 in. 31.8 mm

* GP = General Purpose; HR = High Resolution; C = Composite.

44 * See appendix for technical details.
 Immersion Transducers
I2, I3, I4

I2, I3, I4 IMMERSION

All model I2, I3 and I4 transducers have straight-

mounted waterproof UHF connectors. Available I2
element diameters are 0.25, 0.375 and 0.5 inch (6, 10
and 13 mm). I3 have 0.75 inch (19 mm) and I4 have
1.0 inch (25 mm) element diameters. GP series* offer
the best combination of sensitivity and resolution for
general applications. HR series* are highly-damped
for applications where high resolution is required.
C series* have piezocomposite elements and offer
superior penetration, resolution and signal-to-noise
ratio in highly-attenuative and coarse-grain materials.

PART NUMBERS
Frequency Element Diameter Part Number
(MHz) inch mm Case Focus GP HR C
Immersion Transducers are typically used in
None 00-011201 NF 00-011313 NF
automated and manual-scanning systems using
0.75 19 I3 Spherical 00-011201 X.XS 00-011313 X.XS water or other liquid as a coupling medium. This
Cylindrical 00-011201 Y.YC 00-011313 Y.YC enables the inspection of parts with complex
1
None 00-011314 NF 00-010683 NF geometries and near-surface resolution superior
1 25.4 I4 Spherical 00-011314 X.XS 00-010683 X.XS to that of contact transducers. Spherical (point) or
Cylindrical 00-011314 Y.YC 00-010683 Y.YC cylindrical (line) focusing can further improve
None 00-011315 NF 00-011316 NF 00-011317 NF sensitivity and resolution. Focal length and focal
0.25 6.4 I2 Spherical 00-011315 X.XS 00-011316 X.XS 00-011317 X.XS type must be specified.
Cylindrical 00-011315 Y.YC 00-011316 Y.YC 00-011317 Y.YC
None 00-011318 NF 00-011319 NF 00-011144 NF
0.375 9.5 I2 Spherical 00-011318 X.XS 00-011319 X.XS 00-011144 X.XS
Cylindrical 00-011318 YC 00-011319 Y.YC 00-011144 Y.YC VELOCITY TESTING
None 00-010830 NF 00-011114 NF 00-011320 NF
2.25 0.5 12.7 I2 Spherical 00-010830 X.XS 00-011114 X.XS 00-011320 X.XS Frequency Element Diameter
Cylindrical 00-010830 Y.YC 00-011114 Y.YC 00-011320 Y.YC (MHz) inch mm Case Focus C
None 00-011321 NF 00-011322 NF 00-011146 NF
0.25 6.4 I2 None 00-011403
0.75 19 I3 Spherical 00-011321 X.XS 00-011322 X.XS 00-011146 X.XS
5 0.375 9.5 I2 None 00-011404
Cylindrical 00-011321 Y.YC 00-011322 Y.YC 00-011146 Y.YC
None 00-011323 NF 00-011324 NF 00-011353 NF
0.5 12.7 I2 None 00-010437
1 25.4 I4 Spherical 00-011323 X.XS 00-011324 X.XS 00-011353 X.XS
Cylindrical 00-011323 Y.YC 00-011324 Y.YC 00-011353 Y.YC
None 00-011325 NF 00-011326 NF 00-011327 NF
0.25 6.4 I2 Spherical 00-011325 X.XS 00-011326 X.XS 00-011327 X.XS
Cylindrical 00-011325 Y.YC 00-011326 Y.YC 00-011327 Y.YC
None 00-011328 NF 00-011329 NF 00-011141 NF
0.375 9.5 I2 Spherical 00-011328 X.XS 00-011329 X.XS 00-011141 X.XS
Cylindrical 00-011328 Y.YC 00-011329 Y.YC 00-011141 Y.YC
None 00-011330 NF 00-011331 NF 00-010858 NF
3.5 0.5 12.7 I2 Spherical 00-011330 X.XS 00-011331 X.XS 00-010858 X.XS
Cylindrical 00-011330 Y.YC 00-011331 Y.YC 00-010858 Y.YC
None 00-011332 NF 00-011333 NF 00-011334 NF
0.75 19 I3 Spherical 00-011332 X.XS 00-011333 X.XS 00-011334 X.XS
Cylindrical 00-011332 Y.YC 00-011333 Y.YC 00-011334 Y.YC
None 00-011335 NF 00-011336 NF 00-010586 NF
1 25.4 I4 Spherical 00-011335 X.XS 00-011336 X.XS 00-010586 X.XS
Cylindrical 00-011335 Y.YC 00-011336 Y.YC 00-010586 Y.YC

Chart continues on page 46

* GP = General Purpose; HR = High Resolution; C = Composite.

* See appendix for technical details. 45
 Immersion Transducers
I2, I3, I4

PART NUMBERS CONTINUED CASE DIMENSIONS

Frequency Element Diameter Part Number
(MHz) inch mm Case Focus GP HR C
None 00-011337 NF 00-011351 NF 00-011338 NF I2
0.25 6.4 I2 Spherical 00-011337 X.XS 00-011351 X.XS 00-011338 X.XS E
Cylindrical 00-011337 Y.YC 00-011351 Y.YC 00-011338 Y.YC
None 00-011339 NF 00-011340 NF 00-010679 NF B
0.375 9.5 I2 Spherical 00-011339 X.XS 00-011340 X.XS 00-010679 X.XS C
Cylindrical 00-011339 Y.YC 00-011340 Y.YC 00-010679 Y.YC
None 00-010778 NF 00-010594 NF 00-011013 NF A
Element Ø
5 0.5 12.7 I2 Spherical 00-010778 X.XS 00-010594 X.XS 00-011013 X.XS D
inch 0.25 0.375 0.5
Cylindrical 00-010778 Y.YC 00-010594 Y.YC 00-011013 Y.YC mm 6.4 9.5 12.7
None 00-010585 NF 00-011341 NF 00-010868 NF 0.63 in. 0.63 in. 0.63 in.
A
0.75 19 I3 Spherical 00-010585 X.XS 00-011341 X.XS 00-010868 X.XS 16 mm 16 mm 16 mm

Cylindrical 00-010585 Y.YC 00-011341 Y.YC 00-010868 Y.YC 1.4 in 1.4 in 1.4 in
B
None 00-011152 NF 00-011350 NF 00-011153 NF 35.6 mm 35.6 mm 35.6 mm
0.73 in. 0.73 in. 0.73 in.
1 25.4 I4 Spherical 00-011152 X.XS 00-011350 X.XS 00-011153 X.XS C
18.5 mm 18.5 mm 18.5 mm
Cylindrical 00-011152 Y.YC 00-011350 Y.YC 00-011153 Y.YC
1.55 in. 1.55 in. 1.55 in.
None 00-011352 NF 00-010833 NF 00-011342 NF D
39.4 mm 39.4 mm 39.4 mm
0.25 6.4 I2 Spherical 00-011352 X.XS 00-010833 X.XS 00-011342 X.XS E 5/8 - 24 UNEF
Cylindrical 00-011352 Y.YC 00-010833 Y.YC 00-011342 Y.YC
None 00-010825 NF 00-010644 NF 00-011343 NF
0.375 9.5 I2
I3
Spherical 00-010825 X.XS 00-010644 X.XS 00-011343 X.XS
Cylindrical 00-010825 Y.YC 00-010644 Y.YC 00-011343 Y.YC
10
None 00-010595 NF 00-011349 NF 00-011344 NF
Element Ø
0.5 12.7 I2 Spherical 00-010595 X.XS 00-011349 X.XS 00-011344 X.XS
Cylindrical 00-010595 Y.YC 00-011349 Y.YC 00-011344 Y.YC
B inch 0.75
mm 19
None 00-011148 NF 00-010369 NF 00-011345 NF C
1.0 in.
0.75 19 I3 A
Spherical 00-011148 X.XS 00-010369 X.XS 00-011345 X.XS 25.4 mm
Cylindrical 00-011148 Y.YC 00-010369 Y.YC 00-011345 Y.YC A 1.3 in.
B
None 00-011149 NF 00-011346 NF 33 mm
0.25 6.4 I2 Spherical 00-011149 X.XS 00-011346 X.XS C 5/8 - 24 UNEF
Cylindrical 00-011149 Y.YC 00-011346 Y.YC
None 00-010597 NF 00-011347 NF
15 0.375 9.5 I2 Spherical 00-010597 X.XS 00-011347 X.XS
Cylindrical 00-010597 Y.YC 00-011347 Y.YC

0.5 12.7 I2
None
Spherical
00-010774 NF
00-010774 X.XS
I4
Cylindrical 00-010774 Y.YC
Element Ø
B inch 1
mm 25.4
C 1.25 in.
A
A 31.8 mm
1.35 in.
B
34.3 mm
C 5/8 - 24 UNEF

46
 Immersion Transducers
IR

IR IMMERSION

Immersion Transducers are typically used in automatic and

manual scanning systems using water or other liquid as a
coupling medium to enable the inspection of parts with
complex geometries and near-surface resolution superior
to that of contact transducers. Spherical (point) or
cylindrical (line) focusing can further improve sensitivity
and resolution. Focal length and focal type must be specified.

Model IR transducers have right-angle-mounted waterproof

UHF connectors and small case design for applications where
space is limited. Available element diameters are 0.25, 0.375 and 0.5 inch
(6, 10 and 13 mm). GP series* offer the best combination of sensitivity and
resolution for general applications. HR series* are highly damped for applications
where high resolution is required. C series* have piezocomposite elements and
offer superior penetration, resolution and signal-to-noise ratio in highly attenuative
and coarse grain materials.

PART NUMBERS VELOCITY TESTING

Frequency Element Diameter Part Number Frequency Element Diameter
(MHz) inch mm Focus GP HR C (MHz) inch mm Focus C
None 00-011385 NF 00-011386 NF 00-011387 NF 0.25 6.4 None 00-010591
0.25 6.4 Spherical 00-011385 X.XS 00-011386 X.XS 00-011387 X.XS 5 0.375 9.5 None 00-010438

Cylindrical 00-011385 Y.YC 00-011386 Y.YC 00-011387 Y.YC 0.5 12.7 None 00-010475

None 00-011388 NF 00-011389 NF 00-011390 NF

2.25 0.375 9.5 Spherical 00-011388 X.XS 00-011389 X.XS 00-011390 X.XS
Cylindrical 00-011388 Y.YC 00-011389 Y.YC 00-011390 Y.YC
None 00-011391 NF 00-011392 NF 00-011393 NF
0.5 12.7 Spherical 00-011391 X.XS 00-011392 X.XS 00-011393 X.XS
Cylindrical 00-011391 Y.YC 00-011392 Y.YC 00-011393 Y.YC
None 00-011394 NF 00-011395 NF 00-011396 NF
0.25 6.4 Spherical 00-011394 X.XS 00-011395 X.XS 00-011396 X.XS
Cylindrical 00-011394 Y.YC 00-011395 Y.YC 00-011396 Y.YC
None 00-011397 NF 00-011398 NF 00-011399 NF
5 0.375 9.5 Spherical 00-011397 X.XS 00-011398 X.XS 00-011399 X.XS
Cylindrical 00-011397 Y.YC 00-011398 Y.YC 00-011399 Y.YC
None 00-011400 NF 00-011401 NF 00-011402 NF
0.5 12.7 Spherical 00-011400 X.XS 00-011401 X.XS 00-011402 X.XS
Cylindrical 00-011400 Y.YC 00-011401 Y.YC 00-011402 Y.YC D

CASE DIMENSIONS
B
Element Ø A
inch mm A B C D
0.25 6.4 5/8 - 24 UNEF 0.75 in. 19 mm 0.75 in. 19 mm 0.94 in. 23.9 mm
0.375 9.5 5/8 - 24 UNEF 0.75 in. 19 mm 0.75 in. 19 mm 0.94 in. 23.9 mm
C
0.5 12.7 5/8 - 24 UNEF 0.75 in. 19 mm 0.75 in. 19 mm 0.94 in. 23.9 mm

* GP = General Purpose; HR = High Resolution; C = Composite.

* See appendix for technical details. 47
 Immersion Transducers
Paintbrush

PAINTBRUSH IMMERSION

Paintbrush Transducers are single-element immersion transducers which give a

greater scanning width than conventional transducers with round or rectangular
elements. They are often used in scanning tanks where large plates, bars, and other
parts are tested which have large surface areas. Their large coverage decreases scan time
dramatically. Like other conventional probes, they can be ordered with GP*, HR* or C*
performance and are available in flat or cylindrical focuses.

PART NUMBERS

Frequency Element Dimensions Part Number

Focus
(MHz) Short Axis Long Axis HR
0.25 in 2.5 in Flat 00-010590 NF
10
(6.4 mm) (63.5 mm) Cylindrical 00-010590 Y.YC
H
Element Dimensions
L
inch mm H L W W
0.25 x 2.5 6.4 x 63.5 0.65 in. 16.5 mm 2.85 in. 72.4 mm 0.75 in. 19 mm

Frequency Element Dimensions Part Number

Focus
(MHz) Short Axis Long Axis HR
0.25 in 1 in Flat 00-010175 NF
10
(6.4 mm) (25.4 mm) Cylindrical 00-010175 Y.YC
H

Element Dimensions
inch mm H W L W L
0.25 x 1 6.4 x 25.4 0.95 in. 24.1 mm 0.75 in. 19 mm 1.5 in. 38.1 mm

The majority of paintbrush transducers are built to specific customer requirements.

These are a few examples of SNI Paintbrush Transducers but do not represent our full capabilites.
Please contact us for specific transducer requests.

* GP = General Purpose; HR = High Resolution; C = Composite.

48 * See appendix for technical details.
 Membrane Transducers
MEMBRANE TRANSDUCERS

The water-filled flexible membrane transducer maximizes the defect response on

irregular entry surfaces, enhancing the ability to inspect irregularly shaped
components with better penetration and resolution.

The current low-frequency models (1.5, 2.25, and 3.5 MHz) were designed to inspect
carbon composite in the aerospace industry - but this technique is applicable to
many other applications and materials.

The transducer is customizable for an easy and accurate inspection process. The
membrane is replaceable and available in two materials - UltraFlex (for maximum
conformability) and UltraWear (for maximum wear). The membrane can also be
filled with water or Glycol liquid (for cold environments).

PART NUMBERS
Frequency Element Diameter
Part Number Mebranes
(MHz) inch mm Ring

0.25 6.4 00-013863 See H20 Membrane Chart

1.5
0.50 12.7 00-013866 See H20 Membrane Chart
0.25 6.4 00-013864 See H20 Membrane Chart
2.25 Membrane
0.50 12.7 00-013867 See H20 Membrane Chart
Transducer Body
0.25 6.4 00-013865 See H20 Membrane Chart Water Column
3.5 Body
0.50 12.7 00-013868 See H20 Membrane Chart

MEMBRANES
Part Number
Fits Thickness Material Characteristics
(Pack of 12)
Most flexible, highly conformable, most protrusion. Recommended for
01-013016 0.25" Element Transducer 50 Micron (.002") UltraFlex
static position testing due to higher coefficient of friction.
More Wear Resistant, medium conformability & protrusion.
01-012373 0.25" Element Transducer 50 Micron (.002") UltraWear
Recommended for scanning due to lower coefficient of friction.
Most wear resistant, less conformability & protrusion. Recommended for
01-012359 0.25" Element Transducer 100 Micron (.004") UltraWear
scanning on flatter objects, less likely choice.
Most flexible, highly conformable, most protrusion. Recommended for
01-013018 0.50" Element Transducer 50 Micron (.002") UltraFlex
static position testing due to higher coefficient of friction.
More Wear Resistant, medium conformability & protrusion.
01-012375 0.50" Element Transducer 50 Micron (.002") UltraWear
Recommended for scanning due to lower coefficient of friction.
Most wear resistant, less conformability & protrusion. Recommended for
01-013018 0.50" Element Transducer 100 Micron (.004") UltraWear
scanning on flatter objects, less likely choice.

49
 Co-Polymer Transducer

Co-Polymer Transducers
Co-Polymer transducers, also known as PVdF transducers, have a wide bandwidth and short impulse
response. Variations in focusing can be requested either as unfocussed, cylindrical or spherical. Standard
frequency ranges between 5MHz and 15MHz. Higher frequencies can be requested but there
are other limitations beyond 15MHz.

Typical applications include immersion scanning of components for small or near-surface defects in:

- Aerospace forgings
- Small-diameter bar stock
- Acoustic microscopy
- Thickness gauging of precision, thin-walled tubing

Element Ø
inch mm A B
0.4 10.2 0.62 in. 15.75 mm 2.05 in. 52.1 mm

A
B

Co-Polymer transducers are manufactured based on specific customer requirements.

Please contact us for co-polymer transducer requests.

50
 Dual Element
ADP

ADP Dual-Element Contact Transducers

Model ADP are small-diameter, low-profile transducers

with 2 fixed co-axial cables and come standard with potted
BNC connectors but are also available with Lemo-00. They are
especially suitable for flaw detection and thickness measurement
on pitted, curved, and irregular surfaces. Because the elements are
mounted on internal delay lines they can be contoured to fit I.D. or
O.D. curved surfaces. All ADPs are C series* which has piezocomposite
elements and offer superior penetration, resolution and signal-to-noise
ratio in highly attenuative and coarse grain materials.

Dual-Element Contacts are longitudinal-wave (straight beam)

transducers designed for near-surface and thin range flaw detection and
thickness measurement. Two elements, one transmitter and one receiver, are
mounted at an included (roof) angle to improve signal-to-noise ratio (SNR) and
optimize near-surface resolution.

PART NUMBERS
Frequency Element Diameter Part Number (Cable option)
(MHz) inch mm Potted BNC Potted Lemo-00
0.25 6.4 00-011405 00-011405-LEMO
2.25 0.375 9.5 00-011406 00-011406-LEMO
0.5 12.7 00-011407 00-011407-LEMO
0.25 6.4 00-011408 00-011408-LEMO
3.5 0.375 9.5 00-011409 00-011409-LEMO
0.5 12.7 00-011410 00-011410-LEMO
0.25 6.4 00-010656 00-010656-LEMO
5 0.375 9.5 00-010655 00-010655-LEMO
0.5 12.7 00-011411 00-011411-LEMO
0.25 6.4 00-011412 00-011412-LEMO A
10 0.375 9.5 00-011413 00-011413-LEMO
0.5 12.7 00-011414 00-011414-LEMO

B
CASE DIMENSIONS
Element Ø
inch mm A B C
C
0.25 6.4 0.50 in. 12.7 mm 0.64 in. 16.3 mm 0.28 in. 7.1 mm
0.375 9.5 0.62 in. 15.7 mm 0.64 in. 16.3 mm 0.41 in. 10.4 mm
0.5 12.7 0.75 in. 19 mm 0.68 in. 17.3 mm 0.60 in. 15.2 mm

* C = Composite.
* See appendix for technical details. 51
 Dual Element
DU

DU Dual-Element Contact Transducers

Model DU are general purpose dual-element transducers

with side-mounted Microdot connectors. Replaceable/
interchangeable delay lines and cross-talk barriers greatly
extend versatility, cost-effectiveness, service life and can be
contoured to fit I.D. or O.D. curved surfaces.

Dual-Element Contacts are longitudinal-wave (straight beam)

transducers designed for near-surface and thin-range flaw
detection and thickness measurement. Two elements, one
transmitter and one receiver, are mounted at an included (roof)
angle to improve signal-to- noise ratio and optimize near-surface
resolution.

DU PART NUMBERS
Frequency Element Dimensions Part Number C
(MHz) inch mm C Delay Set Accessories
0.5 x 0.5 12.7 x 12.7 00-012322 01-010740 Dual Cable
2.25
0.5 x 1 12.7 x 25.4 00-012323 01-010741 MD - BNC
0.5 x 0.5 12.7 x 12.7 00-010487 01-010740 6-ft (1.83 m)
5
0.5 x 1 12.7 x 25.4 00-010584 01-010741 07-010030 A

Element Dimensions
inch mm A B C
0.5 x 0.5 12.7 x 12.7 0.89 in. 22.6 mm 0.92 in. 23.4 mm 0.78 in. 19.8 mm
0.5 x 1 12.7 x 25.4 1.39 in. 35.3 mm 0.92 in. 23.4 mm 0.78 in. 19.8 mm B

DU-F PART NUMBERS

Frequency Element Dimensions Part Number
DU-F model transducers are an alternative to the regular
(MHz) inch mm C Accessories DU dual element series. They are constructed with
0.5 x 0.5 12.7 x 12.7 00-013899 Dual Cable composite ceramic and integral delays and offer a lower
2.25
0.5 x 1 12.7 x 25.4 00-013900 MD - BNC price entry point that the standard DU models. They are
0.5 x 0.5 12.7 x 12.7 00-013898 6-ft (1.83 m)
effective with coarse grain/attenuative materials when a
5 single transducer inspection is not viable.
0.5 x 1 12.7 x 25.4 00-011499 07-010012

Element Dimensions
inch mm A B C
0.5 x 0.5 12.7 x 12.7 0.89 in. 22.6 mm 0.7 in. 17.8 mm 0.78 in. 19.8 mm B
0.5 x 1 12.7 x 25.4 1.39 in. 35.3 mm 0.7 in. 17.8 mm 0.78 in. 19.8 mm

C A

52
 DHT-400
HIGH-TEMP DUAL ELEMENT

FOR THICKNESS MEASUREMENTS

ON ROUGH OR CORRODED SURFACES

The SensorScan Model DHT-400 Ultrasonic Transducer is a general-purpose

sensor for measuring the remaining wall thickness on rough metal ID and OD
surfaces due to corrosion and/or erosion. The transducer can be used
intermittently (50% duty cycle) over a wide temperature range from 0 to 932°F
(-17.8 to 500°C) and continuously from 0 to 400°F (-17.8 to 204°C). The minimum
and maximum thickness in steel is 0.04” (1.0mm) and 10” (254mm).

Typical applications include its use with common digital thickness gauges or flaw
detectors on boiler/furnace tubes, pipes, tanks, vessels, structures and other
safety-critical components at power plants, refineries, mid- and up-stream Oil & Gas
assets, and chemical facilities.

The DHT-400 is compatible with all major instruments and flaw detectors.

Extension Wand

DHT-400 ACCESSORIES
Probe & Cable Kits Cool Hand Extension Wand

DHT-400 + Lemo-00 Connector DHT-400 + Olympus Probe Rec. 06-016467 06-016468

Frequency
Cable (standard) Connector Cable (standard)
DHT-400 (Nominal) Connector
00-012543 5MHz MD Connector 01-030180 01-030182

00-030003 5MHz MCX Connector 01-030181 01-030183

Cool Hand

Cable Options
Cable Options

Lemo-00 Connector Olympus Probe Recognition Lemo-00 Connector Olympus Probe Recognition 0.749”
BNC Connector (Standard)
(Standard) Connector (Standard) (Armored) Connector (Armored) (19.0 mm)

07-010245 07-010246 07-036032 07-036033 07-036034

07-036036 07-036037 07-036038 07-036039 07-036040

2.155”
(54.7 mm)
5 Sec. Contact, 10 Sec off at 932°F 400°F Heat Up at 932°F
1.975”
(50.2 mm)

~550 Seconds
ø
0.440”
(19.0 mm)
This chart shows a 33% duty cycle at 5 seconds on At 932°F continuous surface contact temp, it takes
and 10 seconds off. The DHT-400 plateaus at over 9 minutes for the sensitive solder joints within
~270°F which keeps the sensitive elements from the transducer to get to a 400°F.
ever reaching 400°F. 53
 Thickness Gauging
Single Element, Dual Element, Phased Array

PRECISION (SINGLE ELEMENT) THICKNESS GAUGING TRANSDUCERS

For use with commercial thickness gauges and flaw detection instruments.
Transducer Contact Diameter Measuring Nominal SNI Part
Model
Type inch mm Range in Steel Frequency Number
00-010415
Alpha2 DFR +
Delay Line
0.3 7.6
0.007 to 1 inch
15 MHz 00-010417 CA211 +
Removable 0.18 to 25.4 mm
Standard 0.60 to 20 inch
CA211 + 0.75 19 5 MHz 00-010415
Contact 1.5 to 508 mm
Small 0.60 to 10 inch
Alpha2 F + 0.375 9.7 10 MHz 00-010625
Contact 1.5 to 254 mm
Alpha2 Mini Thin Range 0.005 to 0.2 inch
0.19 4.8 20 MHz 00-010589
DFR + Delay Line 0.13 to 5.1 mm
Delay Line 0.065 or 1.7 or 0.008 to 0.175 inch
Pencil Probe 15 MHz 00-011039
Pencil Case 0.090 2.3 0.20 to 0.44 mm

CORROSION (DUAL ELEMENT) THICKNESS GAUGING TRANSDUCERS

For use with commercial corrosion thickness gauges and flaw detection instruments.
For use with commercial corrosion thickness gauges and flaw detection instruments.
Transducer Contact Diameter Measuring Nominal SNI Part
Model
Type inch mm Range in Steel* Frequency Number 00-010424
0.030 to 2.0 inch FH2E +
FH2E + Fingertip 0.375 9.7 7.5 MHz 00-010424
0.76 to 50.8 mm
0.030 to 2.0 inch
FH2E + TM Fingertip 0.375 9.7 7.5 MHz 00-013934
0.76 to 50.8 mm
Fingertip 0.030 to 2.0 inch
FH2E + WR 0.55 14 7.5 MHz 00-010565
Wear Resistant 0.76 to 50.8 mm
0.030 to 2.0 inch
FH2E + MD Fingertip 0.375 9.7 7.5 MHz 00-011017
0.76 to 50.8 mm
Fingertip 0.030 to 1.0 inch
FH2E + M
Small Diameter
0.28 7.1
0.76 to 25.4 mm
7.5 MHz 00-010675
00-013934
0.030 to 2.0 inch FH2E + TM
FH2E + with BNC Fingertip 0.375 9.7 7.5 MHz 00-010532
0.76 to 50.8 mm
Studded Boiler 0.060 to 2.0 inch
FH2E + BT 0.375 9.7 7.5 MHz 00-010676
Tube 1.5 to 50.8 mm
0.024 to 2.4 inch
DA 512 + Fingertip 0.295 7.5 7.5 MHz 00-010638
0.6 to 61 mm
0.025 to 2 inch
SNI 525 Potted Fingertip 0.2 5 10 MHz 00-012223
0.6 to 50.8 mm
0.016 to 1.5 inch
FS 512+ Fingertip 0.295 7.5 15 MHz 00-013987
0.4 to 38.1 mm
Elevated 0.060 to 8.0 inch**
SNI 560 0.63 16 mm 5 MHz 00-012533
Temperature 1.52 to 203.2 mm

* The measurement range is dependent on the part’s material type, geometry, surface condition,
and temperature. Another consideration is proper selection of couplant.
** With intermittent contact, the maximum part’s surface temperature for the SNI 560 is 450°F (232°C)

54
 Thickness Gauging
Case Dimensions

Alpha2 DFR + CA211 + Alpha2 F + Alpha2 Mini DFR + FH2E +

B B
B B B

C A A
A A
A

FH2E + TM FH2E + WR FH2E + MD FH2E + M FS 512+

B B
B B B

A A C A
A A

FH2E + w/ BNC FH2E + BT DA 512 + SNI 525

B
B B B
A
A A A

Case Dimensions Case Dimensions

Case Type A B C Case Type A B C

Alpha2 DFR + 0.51 in. 13 mm 0.83 in. 21.1 mm 0.3 in. 7.6 mm FH2E + M 0.28 in. 7.1 mm 0.725 in 18.4 mm

CA211 + 0.75 in. 19.1 mm 0.65 16.5 mm FS 512+ 0.29 in. 7.4 mm 0.67 in. 17 mm

Alpha2 F + 0.5 in 12.7 mm 0.65 16.5 mm FH2E + w/ BNC 0.38 in. 9.7 mm 0.73 in. 18.5 mm

Alpha2 Mini DFR + 0.4 in. 10.2 mm 0.46 in. 11.7 mm FH2E + BT 0.38 in. 9.7 mm 2.0 in. 50.8 mm

FH2E + 0.38 in. 9.7 mm 0.73 in. 18.5 mm DA 512 + 0.29 in. 7.4 mm 0.67 in. 17 mm

FH2E + TM 0.38 in. 9.7 mm 0.93 in. 23.6 mm SNI 525 0.2 in. 5.1 mm 0.79 in. 20.1 mm

FH2E + WR 0.54 in. 13.7 mm 0.73 in. 18.5 mm Pencil Probe See page 28 for Pencil Probe Dimensions

FH2E + MD 0.38 in. 9.7 mm 1.04 in. 26.4 mm 1.0 in. 25.4 mm

55
 Accessories
Cables, Adapters, and Splitters

CABLES
Cable Material Length Part Number Cable Material Length Part Number
BNC - BNC RG58 6-ft (1.83 m) 07-010018 00-Lemo - MCX RG174 TPR 6-ft (1.83 m) 07-010035
BNC - MD RG174 TPR 6-ft (1.83 m) 07-010012 BNC - MCX (RA) RG174 TPR 6-ft (1.83 m) 07-010008
BNC - MCX RG174 TPR 6-ft (1.83 m) 07-010007 Dual BNC - Dual MD RG174 TPR 6-ft (1.83 m) 07-010030
BNC - 00-Lemo RG174 TPR 6-ft (1.83 m) 07-010014 Dual 00-Lemo - Dual MD RG174 TPR 6-ft (1.83 m) 07-010032
00-Lemo - MD RG174 TPR 6-ft (1.83 m) 07-010028 Lemo 1 - MD RG174 TPR 6-ft (1.83 m) 07-020176
00-Lemo - 00-Lemo RG174 TPR 6-ft (1.83 m) 07-010034 Lemo 1 - BNC RG174 TPR 6-ft (1.83 m) 07-020175

CONVENTIONAL ADAPTERS PAUT CONNECTORS

Adaptors Part Number • IPEX

• ZPAC
BNC Female to Female RF Adaptor 10-012572
• Hypertronics
Male Lemo-00 to Female BNC Adapter 10-010850
• Mentor
Female Lemo-00 to Male BNC Adapter 10-010891 • Phasor
Male BNC to Female Right Angle BNC Adapter 10-010938 • Others available
Female BNC to Male Lemo-00 Adapter 10-010790 upon request

(L to R) Hypertronics, ZPAC, IPEX

PAUT SPLITTERS & ADAPTERS

Sensor Networks can make splitters and extension cables

with any phased-array connector types and lengths that you
MICRODOT
need. To order a splitter or extension cable, contact us and
provide us with the information based on the prompt below.

The connector type for end A (Array Side): BNC

The connector type for end B (Instrument Side:

The cable length needed is: LEMO-00

A B LEMO 1
C
ADAPTER
MCX*

RIGHT-ANGLE MCX*

B
A
C *MCX connectors are snap-in and can swivel,
preventing the risk of back threading.

SPLITTER

56
 Screws
Wedge and Delay-Line Attachment Screws

Length
Ref # Case Captive Thread Size SNI #
in mm
.25 in. MSWS Yes #1-64 0.63 15.88
1 10-010174
.5 in. MSWS Yes #1-64 0.63 15.88
A1 Yes M3 0.39 10
A2 Yes M3 0.39 10
A4 Yes M3 0.39 10
A5 Yes M3 0.39 10
A31 Yes M3 0.39 10
2 06-010685
A32 Yes M3 0.39 10
AL Yes M3 0.39 10
AM Yes M3 0.39 10
E1 Yes M3 0.39 10
LM Yes M3 0.39 10
A10 Yes M3 0.87 22
A11 Yes M3 0.87 22
3 A12 Yes M3 0.87 22 10-010724
A14 Yes M3 0.87 22
A27 Yes M3 0.87 22
4 A15 Yes #1-64 0.19 4.76 10-010564
5 A25 Yes #0-80 0.25 6.35 06-016930
CL (Dual-Linear) NO M2 0.3 8
6 10-010895
CS NO M2 0.3 8
7 E2 Yes #1-72 0.5 12.7 06-014227
E3 Yes #4-40 0.5 12.7
8 10-010252
E4 Yes #4-40 0.5 12.7
9 E5 Yes #2-56 0.37 9.5 10-010960
10 PWZ1 Yes M3 0.63 16 06-016925
11 AWS / SWS Yes #4-40 1 25 10-010173
12 DU NO #2-56 0.56 14.29 10-010961
13 DU-F NO #2-56 0.25 6.35 10-010962
Kit Includes 10 each of all 13 screws 10-011037

#1 #2 #3 #4 #5 #6 #7 #8 #9 #10 #11 #12 #13

10-010174 06-010685 10-010724 10-010564 06-016930 10-010895 06-014227 10-010252 10-010960 06-016925 10-010173 10-010961 10-010962 57
 Appendix
High Resolution Series General Purpose Series Composite or Piezo-composite Series

HR: High Resolution Series of transducers are GP: General Purpose Series of transducers C: Composite (Piezocomposite) Series of
highly damped and recommended for are recommended for most applications and transducers have superior sensitivity and
applications where enhanced axial and have a good trade-off between sensitivity and penetration especially in highly-attenuative
near-surface resolution are more important. resolution. They have a medium frequency materials. C Series have both higher resolution,
Generally includes thickness measurement and bandwidth of 40-65% at -6db but with more sensitivity, and have wide bandwidth (60-120%
near-surface flaw detection. HR series have ring-down cycles in the waveform. at -6db) due to the lower acoustic impedance
less sensitivity than the GP or C series with of the material. They couple more efficiently
-6db frequency bandwidth of 50-100% range. into plastic wedges, delay lines, and water.

Transducer Certification

Ultrasonic Transducer Certification Ultrasonic Beam Profile

Generic Image of Transducer

Phone: 814-466-7207 Phone: 814-466-7207

Website: www.sensornetworksinc.com Website: www.installedsensors.com

Transducer Information Transducer Information Beam Profile

*Part Number: 00-010778NF *Part Number: XDCR100N
*Serial Number: 778PRETESTk2 RF Waveform Image *Serial Number: U11CA7
Transducer Description: Transducer Description: XDCR 100, .75" DIA, 5 MHz, 2.5" CYL
I-I2-5Mhz-.50"-GP-NF-UHF FCS, 13A-1967_B CASE

Frequency: 5Mhz Frequency: 5MHz

Element Size: .50" Element Size: .75"

Transducer Measurements per ASTM E1065 Transducer Measurements per ASTM E1065
Date: Jun 4, 2018 Date: Jun 4, 2019
Time: 6:44 PM Time: 10:18 AM
Operator: DEH Operator: KPR
Transducer Disposition: PASS
**Transducer Disposition: PASS
-3dB Beam length (in): 0.505"
Relative Sensitivity: 68dB
Center Frequency: 5.37MHz
-6dB Bandwidth: 67.66% Frequency Spectrum

Test Setup & Conditions

Test Procedure Number:
Test Setup & Conditions
Test Object: 1/4" SST ROD
Test Procedure Number: Tp Water Path (in): 3.0"
Test Object: 3" H20-SST Pulser Settings
Pulser Settings Repetition Rate: 4
Repetition Rate: 4 Pulse Amplitude: 5
Pulse Amplitude: 5 Pulse Energy: 2 - LowZ
Pulse Energy: 2 - LowZ Damping: 9
Damping: 9 Receiver Settings Test Equipment
Receiver Settings Test Equipment Mode: Pulse Echo Pulser/Receiver: JSR DPR300
Mode: Pulse Echo Pulser/Receiver: IDPR300 Gain: 20 + 2 Pulser Serial Number: DA0901
Gain: 10 + 1 Pulser Serial Number: DA0901 Low Pass Filter (MHz): 35 MHz Pulser Calibration Date: Dec 19, 2019
Low Pass Filter (MHz): 35 MHz Pulser Calibration Due Date: Dec 14, 2018 High Pass Filter (MHz): 1 MHz Oscilloscope Model: DPO2022B
High Pass Filter (MHz): 1 MHz Oscilloscope Model: DPO2022B Oscilloscope Serial Number: C030032
Oscilloscope Serial Number: C030032 Special Notes: Oscilloscope Calibration Date: Oct 11, 2019
Oscilloscope Calibration Due Date: Oct 12, 2018 Software: 1.0.3
Customer Software: 1.2.0 Cable: 6FT RG-58
Cable: 6FT RG-58
*Please reference Transducer Part Number and Serial Number in any correspondence
*Please reference Transducer Part Number and Serial Number in any correspondence
Customer MAC
** This item was manufactured and tested according to product specific parameters. The "Pass" Disposition confirms that all
58 steps in the manufacturing process were completed satisfactorily and that all test requirements were satisfied.
 Appendix
Phased-Array Transducer Certification

Linear Phased Array Ultrasonic Transducer Certification

Linear Phased Array Ultrasonic Transducer Certification

Image of Transducer
Image of Transducer

Phone: 814-466-7207
Phone: 814-466-7207
Website: www.sensornetworksinc.com
Website: www.sensornetworksinc.com
Transducer Information
Transducer Information *Part Number: 00-010536-SMT
*Serial Number: U115CV Typical RF Waveform and Frequency Spectrum (Element 14)
*Part Number: 00-010848
Transducer Description:
*Serial Number: U1179S Typical RF Waveform and Frequency Spectrum (Element 16) 5MHz, 28EL, 1.6mmP X 10mm, 30m
Transducer Description: CBL, Rectangular

D1, 10.0MHz, 0.6mm x 10mm Probe Type:

Housing: Rectangular

Probe Type: Frequency: 5.0MHz

D1
QUICK Element Pitch: 1.6 mm
Housing: Element Elevation: 10 mm
CONNECT Number of Elements: 28
Frequency: 10.0MHz
Cable Jacket: PU Frequency Spectrum
Element Pitch: 0.6mm Cable Length: 30M
Element Elevation: 10mm Connector Type: SAMTEC
Number of Elements: 32 Transducer Measurements per ASTM E1065
Cable Jacket: N/A Frequency Spectrum Date: 6/13/2018
Cable Length: N/A Time: 9:20:55AM
Operator: KYLE RYAN
Connector Type: DISCONNECT
**Transducer Disposition: PASS
Transducer Measurements per ASTM E1065
Average Relative Sensitivity: -45dB
Date: 10/29/2018 Average Center Frequency: 4.80MHz
Time: 9:25:00AM Average -6dB Bandwidth: 78.70%
Operator: KYLE RYAN
**Transducer Disposition: PASS
Test Setup & Conditions Test Equipment
Average Relative Sensitivity: -48dB Test Procedure Number: TP Acquisition Unit: TC3
Test Object: 20mm REX BW Acq. Unit Serial Number: 17054368
Average Center Frequency: 9.80MHz Pulser Settings Acq. Unit Calibration Due Date: April 06,2019
Average -6dB Bandwidth: 66.30% Pulse Width: 100ns Hardware Version: 1.1
Pulse Voltage: -12.3V Software: 1.2.1
Adapter: 07-020155

Test Setup & Conditions Test Equipment

Test Procedure Number: TP-010848 Acquisition Unit: TC3
Special Notes:
Test Object: 1/2" REX BW Acq. Unit Serial Number: 17054368
Pulser Settings Acq. Unit Calibration Due Date: April 06,2019
Pulse Width: 40ns Hardware Version: 1.1
Pulse Voltage: -12.3V Software: 1.2.3
*Please reference Transducer Part Number and Serial Number in any correspondence
Adapter: IPEX **This item was manufactured and tested according to product specific parameters. The "Pass" Disposition confirms that all steps in the
manufacturing process were completed satisfactorily and that all test requirements were satisfied.
Customer NDTS

Special Notes:

Document #: REF-0100036 Rev A

*Please reference Transducer Part Number and Serial Number in any correspondence
**This item was manufactured and tested according to product specific parameters. The "Pass" Disposition confirms that all steps in the

Customer
All SensorScan® Transducers carry a one-year warranty from the date of purchase, for the original
manufacturing process were completed satisfactorily and that all test requirements were satisfied.
SONOTEST
owner, covering defects in materials and workmanship.

Document #: REF-0100036 Rev A

59
 2
ULTRASONIC
SOLUTIONS

1 3
INSTALLED
SENSORS
REMOTE
VISUAL

366 Walker Drive - Suite 200

State College, PA 16801, USA
Offices In - Houston • Hong Kong • Osaka • Köln

www.sensornetworksinc.com
[email protected]
+1 (814) 466-7207
Find us on

You
© Sensor Networks, Inc. 2022. All rights reserved.
Tube Sensor Networks, Inc. and SensorScan are registered trademarks of Sensor Networks, Inc.
 高温超音波探傷用トランスデューサー
フェーズドアレイ
TOFD
腐食検査用デュアルリニアアレイ
ウエッジ

常温から高温まで、
欠陥検出とサイジングを
1つの探触子でカバー

高温材料に対するフェーズドアレイ、、
デュアルリニアアレイを用いた腐食検査や超音波
探傷をお考えなら、はより良いソリューショ
ンを提供することができます。私たちは、金属表
面の温度が℃まで動作可能なフェーズドアレ
イ探触子、ウェッジを開発し、様々なテストを行
っています。

温度変化によるトランスデューサーとウェッジ
の屈折角の変化は計算可能であり、キャリブレ
ーションを行うことで管理・補正することがで
きます。添付のデータは材料温度が減衰量、
周波数、音速、屈折角のいずれについても影響
することを示しています。新しい探触子は製油
所や発電所などの高温環境下でも使用できるよ
うに設計されており、様々な手法の超音波探傷
を行うことが可能となります。
 フェーズドアレイ
リニア: 縦波・横波

高温用アレイは、溶接部検査、チューブやパイプの検査、
レール、圧力容器など、さまざまな高温アプリケーション
を適切にサポートする汎用性の高い探触子です。これら
の探触子には、コネクタ付きのケーブルが標準
仕様で取り付けられています。ウェッジには中温用
（℃～℃）と高温用（℃～℃）のつの仕様
があります。 また、各ウェッジの種類には、屈折角 ～
°と°のモデルが用意されています。

探触子 エレメントピッチ エレベーション

ケース 周波数
エレメント数 製品コード
タイプ (MHz) in mm in mm

A10 5 16 0.024 0.6 0.39 10 00-015631

A11 5 32 0.024 0.6 0.39 10 00-015632

ウエッジ ウエッジ
ケース 使用温度範囲 屈折角* 製品コード L W H
A10 Mid Temp (100°C to 150°C) 0° 01-013350-IHC 0.98 in. 24.9 mm 1.58 in. 40.1 mm 0.79 in. 20.1 mm

A10 High Temp (150°C to 200°C) 0° 01-013351-IHC 0.98 in. 24.9 mm 1.58 in. 40.1 mm 0.79 in. 20.1 mm

A10 Mid Temp (100°C to 150°C) N55S (30-70°) 01-013352-IHC 0.91 in. 23.1 mm 1.30 in. 33 mm 0.56 in. 14.2 mm

A10 High Temp (150°C to 200°C) N55S (30-70°) 01-013353-IHCˆ 1.4 in. 35.6 mm 1.58 in. 40.1 mm 0.7 in. 17.8 mm

A11 Mid Temp (100°C to 150°C) 0° 01-013355-IHC 1.38 in. 35.1 mm 1.58 in. 40.1 mm 0.79 in. 20.1 mm

A11 High Temp (150°C to 200°C) 0° 01-013356-IHC 1.38 in. 35.1 mm 1.58 in. 40.1 mm 0.79 in. 20.1 mm

A11 Mid Temp (100°C to 150°C) N55S (30-70°) 01-013357-IHC 1.63 in. 41.4 mm 1.30 in. 33 mm 1.13 in. 28.7 mm

A11 High Temp (150°C to 200°C) N55S (30-70°) 01-013358-IHCˆ 2.25 in. 57.2 mm 1.30 mm 33 mm 1.05 in. 26.7 mm

すべてのウェッジには、ポート、ウェアピン、8mm Ø (0.315 in.) 3mm 深さのジンバルマウントホールが標準装備されています。

ご希望により、これらの機能を省いたウェッジを特別注文することも可能です。

A10 A A11 A 30-70° ウエッジ 0° ウエッジ

H H
H H
L L
W W W
L L

寸法
ケース
L W H A （固定ネジ間隔）
A10 0.91 in. 23.1 mm 0.63 in. 16 mm 0.79 in. 20.1 mm 0.67 in. 17 mm

A11 0.91 in. 23.1 mm 0.98 in. 24.9 mm 0.79 in. 20.1 mm 0.67 in. 17 mm

* ウエッジの屈折角はカスタマイズ可能 2
^
ウェッジの寸法は変更になる場合があります
 TOFD

高温用TOFD探触子は、従来のTOFD探触子と同様に使用
できますが、最高200℃までの温度に対応するように設計
されています。 TOFD法は、金属溶接部の溶接欠陥の大き
さを測定するために使用される手法です。屈折縦波（L波）
を発生させるダンピング性能が良く広帯域の探触子とウェ
ッジが必要です。高温用TOFD探触子は、ストレートマウント
のマイクロドットコネクタが標準装備されています。
また、TOFDウェッジは200℃までの温度で使用できるよう
に設計されており、2つの給水口とジンバルマウントホール
を備えています。

探触子 ケース 周波数 振動子φ

製品コード
タイプ (MHz) in mm

3/8 - 32 2.25 0.25 6.4 00-015636

3/8 - 32 5 0.25 6.4 00-015635

ウエッジ ケース
使用温度範囲 屈折角* 製品コード
タイプ

3/8 - 32 最大 200°C 45° 縦波 01-013467

3/8 - 32 最大 200°C 60° 縦波 01-013468

3/8 - 32 最大 200°C 70° 縦波 01-013469

W H
H W
L

寸法 寸法
ケース ウエッジ
L W H L W H
3/8 - 32 0.41 in. 10.4 mm 0.37 in. 9.5 mm 0.72 in. 18.3 mm 3/8 - 32 0.67 in. 17 mm 1.25 in. 31.75 mm 0.53 in. 13.5 mm

ジンバル取り付け穴 : Ø 5mm (0.2 in.) 、 深さ3mm (0.12 in.)

3 * カーボンスチールでの屈折角
カスタムの屈折角につきましてはお問い合わせください
 デュアルリニア
腐食検査用アレイ

高温用デュアルリニアアレイは、高温での腐食/浸食検査用
に設計されています。
トランスデューサーと交換可能なディレイラインは、200°C
までの温度に耐えられるように設計されています。このデ
ュアルアレイは32個の送信エレメントと32個の受信エレメ
ントを備えており、従来の二振動子探触子よりも大きなビ
ーム範囲を確保することができます。
送信エレメントと受信エレメントの間には角度がついてお
り、被検査材に焦点効果をもたせています。

探触子 ケース 周波数 エレメントピッチ エレベーション

エレメント数 製品コード
タイプ (MHz) in mm in mm
CL 5 64 (32 x 2) 0.058 1.5 0.20 5 00-015634

交換用ディレイ
セラゾール 01-014525

寸法 寸法
ケース
L W Ha Hb
CL 2.58 in. 65.5 mm 1.25 in. 31.8 mm 0.98 in. 24.9 mm 0.22 in. 5.6 mm

取り付け穴間隔 : 1.4 in. (35.6 mm)

W 距離振幅特性曲線
5
0
Ha -5

Hb
相対感度

-10
-15
-20
-25
L -30
0 0.05 0.075 0.1 0.2 0.3 0.4 0.5 0.75 1 1.25
穴の深さ (in.)

4
 中温・高温 テストデータ

中温用ウエッジ ピーク

エコー高さ 25 (°C) との 25 (°C) との

ピーク （ナチュラル）*
音速 25 (°C)との 80% 時の ビーム路程 周波数 周波数
温度 (°C) (in./uS) 音速変化率 ゲイン 変化率 (MHz) 変化率

100°c - 150°c (212 - 302

°F
)
°F 25
50
0.100
0.099
0.00
1.60
21.5
22
0.00
2.33
4.1
4.03
0.00
1.71
• A10 & A11 ケース用ウエッジ 75 0.097 3.19 22.5 4.65 3.96 3.41
• TOFDウエッジ 100 0.095 4.89 23 6.98 3.86 5.85
• デュアルリニアアレイ用ディレイライン
125 0.093 6.89 24 11.63 3.59 12.44
150 0.091 9.38 29.5 37.21 2.76 32.68

175 0.083 17.56 1.22 70.24

屈折角 vs. 温度 音速 vs. 温度 中心周波数 vs. 温度

0.015 4.5

4
屈折角（°）

0.1
3.5

中心周波数 (MHz)
0.095
音速 (in/µS)

0.09 2.5

2
温度 (°C) 0.085
1.5

0.08 1
0 50 100 150 200 0 50 100 150 200
温度 (°C) 温度 (°C)

セラゾール U-60
エコー高さ 25 (°C) との 25 (°C) との
高温用ウエッジ 温度 (°C)
音速
(in./uS)
25 (°C)との
音速変化率
80% 時の
ゲイン
ビーム路程
変化率
周波数
(MHz)
周波数
変化率

セラゾール U-60 *
25 0.117 0.00 16 0.00 4.88 0.00
50 0.116 0.77 16 0.00 4.8 1.64

150°c - 200°c (302 °F

- 392°F) 75 0.116 1.20 16.5 3.13 4.76 2.46
100 0.115 1.97 17.5 9.38 4.66 4.51
• A10 & A11 ケース用ウエッジ
125 0.114 2.65 19.5 21.88 4.27 12.50
• TOFDウエッジ
150 0.113 3.68 23.5 46.88 3.86 20.90
• デュアルリニアアレイ用ディレイライン
175 0.113 3.42 29.5 84.38 3.91 19.88
200 0.112 4.53 39 143.75 6.05 -23.98

屈折角 vs. 温度 音速 vs. 温度 中心周波数 vs. 温度

0.118 7

0.117 6
中心周波数 (MHz)

0.116 5
音速 (in/µS)
屈折角（°）

0.115 4

0.114 3

0.113 2

0.112 1
温度 (°C) 0.111 0
0 50 100 150 200 250 0 50 100 150 200 250
温度 (°C) 温度 (°C)

* このデータはトランスデューサ、ウェッジ、測定対象物のすべてが150℃（ピーク）
5 または200℃（セラゾール）で計算されています。
実際の検査では、測定対象物からトランスデューサまで温度勾配があります。
200°Cで探傷を行った直径10インチ（254mm）×厚さ3/8インチ
（9.7mm）の炭素鋼パイプの実際の溶接欠陥

画像提供： Eddyfi

高温用探触子・ウェッジ製品一覧

製品コード 商品概要

リニア 00-015631 16エレメント 高温用 200°C, 5MHz, 16EL, 0.6mmP x 10mm, 2.5mケーブル, A10, IPEXコネクタ
アレイ 00-015632 16エレメント 高温用 200°C, 5MHz, 16EL, 1.0mmP x 10mm, 2.5mケーブル, A11, IPEXコネクタ
腐食検査用
アレイ 00-015634 64エレメント 高温用 200°C, 5MHz, 腐食検査用, 1.5mmP, 3.0mケーブル, IPEXコネクタ, 脱着式ディレイライン

00-015635 一振動子, 高温用 200°C, TOFD用, 振動子径 0.25”, 5MHz, Microdotコネクタ, 3/8-32 ネジ取り付け式
TOFD
00-015636 一振動子, 高温用 200°C, TOFD用, 振動子径0.25”, 2.25MHz, Microdotコネクタ, 3/8-32 ネジ取り付け式
01-013350-IHC ピーク, 中温用, 屈折角0°（垂直探傷用）, A10
01-013351-IHC セラゾール, 高温用, 屈折角0°（垂直探傷用） , A10
01-013352-IHC ピーク, 中温用, 屈折角30-70°S, N55S, A10
01-013353-IHC セラゾール, 高温用, 屈折角30-70°S, N55S, A10
01-013355-IHC ピーク, 中温用, 屈折角0°（垂直探傷用）, A11
01-013356-IHC セラゾール, 高温用, 屈折角0°（垂直探傷用）, A11
ウエッジ*
01-013357-IHC ピーク, 中温用, 屈折角30-70°S, N55S, A11
01-013358-IHC セラゾール, 高温用, 屈折角30-70°S, N55S, A11
01-013467 ウェッジ, TOFD用, 縦波屈折角45°, 3/8-32 ネジ取り付け式, SSTハウジング, 給水口2個, 高温用200°C
01-013468 ウェッジ, TOFD用, 縦波屈折角60°, 3/8-32 ネジ取り付け式, SSTハウジング, 給水口2個, 高温用200°C
01-013469 ウェッジ, TOFD用, 縦波屈折角70°, 3/8-32 ネジ取り付け式, SSTハウジング, 給水口2個, 高温用200°C
01-014525 腐食検査アレイ用, セラゾール, 高温用
* すべてのウェッジは、屈折角のカスタマイズや曲面用のR加工が可能です。


〒541-0046
大阪市中央区平野町2丁目5-8
平野町センチュリービル2F
TEL : 06-7878-5805 © Sensor Networks, Inc. 2022. All rights reserved.
https://sensornetworksinc.jp/ Sensor Networks, Inc. is a registered trademark of Sensor Networks, Inc.
JP-Rev. 1.1 - 06/01/22