Approved in the BOS held on 16.09.
2022
20CE3103– STEEL STRUCTURAL DESIGN
(Civil Engineering)
Course
Professional Core Credits 3
Category
Course Type Theory Lecture - Tutorial - Practical 2-1-0
Prerequisite Strength of Materials, Sessional Evaluation 40
Structural Analysis 60
Semester End Exam Evaluation
Total Marks 100
Course CO Compare types of connection and select the suitable connection.
Outcomes 1
CO Design steel tension members with lugs and splices.
2
CO Design steel laced and battened compression members.
3
CO Design laterally supported beams and their connections.
4
CO Design simple laterally unsupported beams and gantry girders.
5
CO Design various types of bases and grillage foundation.
6
UNIT – I
INTRODUCTION: Properties of sections – Types of loads – Permissible
stresses in tension, compression and shear as per IS code.
Course BOLTED CONNECTIONS: Types of bolted joints – Modes of failure of
Content bolted joints – Strength and efficiency of bolted joints – Strength of lap and
butt joints – Design of Bolted joints – Design of bracket connections (beam to
column and beam to beam connections).
WELDED CONNECTIONS: Types of welded joints – Strength of fillet and
butt welds – Design of welded joints – Design of bracket connections (beam
to column and beam to beam connections).
UNIT – II
DESIGN OF TENSION MEMBERS: Design of tension members – Lug
angles – Tension splice.
UNIT – III
1
Approved in the BOS held on 16.09.2022
DESIGN OF COMPRESSION MEMBERS: Design of compression
members – Single and built-up columns – Design of lacing and battens –
Design of eccentrically loaded columns.
UNIT – IV
LATERALLY SUPPORTED BEAMS: Design of simple beams – Design
of built-up beams- Curtailment of flange plates – Connection of flange plate
with flange of beam.
UNIT – V
LATERALLY UNSUPPORTED BEAMS: Permissible bending
compressive stress – Effective length of compression flange – Design of
simple beams – Design of Gantry Girders.
UNIT – VI
DESIGN OF COLUMN BASES: Slab base – Gusseted base – Bases
subjected to moment – Grillage foundation.
Text books TEXTBOOKS:
and 1. S.K. Duggal, Design of Steel Structures, McGraw-Hill education
References publishers, 2nd edition, 2017.
2. S.S. Bhavikatti, Design of Steel Structures, I K International
Publishing house, 4th edition, 2014.
3. N. Subramanian, Design of Steel Structures, Oxford University press,
2nd edition, 2018.
REFERENCE BOOKS:
1. M.R. Shiyekar, Limit State Design in Structural Steel, PHI Learning
publishers, 3rd edition, 2016.
2. Dr. V.L.Shah & Dr. S.R.Karve, Limit State Design of Steel
Structures, Jain Book Agency, 3rd edition, 2012.
3. P.Dayaratnam, Design of Steel Structures, S Chand Publishers,3rd
edition, 2012.
CO-PO Mapping: 3-High Mapping, 2-Moderate Mapping, 1-Low Mapping, - -Not Mapping
PSO1
PSO2
PSO3
PO10
PO11
PO12
PO1
PO2
PO3
PO4
PO5
PO6
PO7
PO8
PO9
CO1 2 1 1 1 - - - - - - - 2 - - -
CO2 3 - 2 - 1 - - 1 - - - 2 1 1 -
CO3 3 1 2 - 1 - - 1 - - - 3 1 1 -
CO4 3 1 2 - 1 - - 1 - - - 2 1 1 -
CO5 3 1 2 - 1 - - 1 - - - 1 1 1 -
2
Approved in the BOS held on 16.09.2022
CO6 3 - 2 - 1 - - 1 - - - 2 1 - -
