-|Transparent Guide|-

Safety Door Lock Switch

Cautions during Use Specifications Contact Composition and Operation

SFDL Series
• Follow instructions in ‘Cautions during Use’. Otherwise, it may cause unexpected accidents. Model SFDL-□□□-□□ SFDL-□□□-C□□ Connection diagram represents the locked status with the operation key inserted.
• Use the switch with the dedicated controller. Do not use the switch with another controller randomly. Directing opening force ≥ 80 N ( : ON, : OFF)
• This unit may be used in the following environments. Directing opening distance ≥ 10 mm : Direct opening action possible

INSTRUCTION MANUAL
- Indoors (in the environment condition rated in ‘Specifications’)
- Altitude max. 2,000m Locking pullout strength ≥ 1,300 N
- Pollution degree 3 Operating speed 0.05 to 1 m/s Contact Connection diagram
- Installation category Ⅲ Operating frequency ≤ 20/min Model (lock monitor+ Contact operation
Lock monitor Door monitor
- Enclosure Type Ⅰ door monitor)
Machanical life cycle ≥ 1,000,000 operations (20/min)
0.35mm amplitude at frequency of 10 to 55 Hz (for 1 min) 9 E1(+) E2(-) 10 Operation key Operation
Vibration (malfunction) complete key
in each X, Y, Z direction for 10 min
Product Components
insertion extraction
TCD210162AD Shock 1,000 m/s2 (≈ 100 G) in each X, Y, Z direction for 3 times
Shock (malfunction) 80 m/s2 (≈ 8 G) in each X, Y, Z direction for 3 times
• Product • Instruction manual • Special type release key -10 to 55℃ 01), storage: -25 to 65 ℃
(Special type release key model) Ambient temperature
(a non freezing or condensation environment)
Thank you for choosing our Autonics product. Lock position
35 to 85 %RH , storage: 35 to 85 %RH 2 42 41 12 11 1
Read and understand the instruction manual and manual thoroughly before using the product. Ambient humidity 42-11
(a non freezing or condensation environment)
Sold Separately
For your safety, read and follow the below safety considerations before using. 1 N.C. /1 N.O. +
SFDL-□A-□□□
For your safety, read and follow the considerations written in the instruction manual, other Protection structure IP67 02) (IEC standard, except for head) 1 N.C./1 N.O. 34-33
8 64 63 34 33 5
manuals and Autonics website. Material Head: zinc, case: polyamide 66, operation key: stainless steel 304 7 6 64-63
Keep this instruction manual in a place where you can find easily. • Operation key: SFD-K▭ Approval ᜨᜪ ᜫ
The specifications, dimensions, etc. are subject to change without notice for product • Slide key unit: SFDL-SDK Lock position
Accessory SFDL-□□□-□□K (Special type release keyse key) : rotating key 2 42 41 12 11 1
GB/T14048.5

improvement. Some models may be discontinued without notice.

• Connector cable for the connector type: SFDL-CND10-□ 42-11
Follow Autonics website for the latest information. Applicable cable AWG22 -
SFDL-□B-□□□ 2 N.C. + 1 N.C./1 N.O.
Connection type Terminal type Connector type 34-33
8 62 61 34 33 5

Safety Considerations Ordering Information Unit weight (packaged) ≈ 375 g (≈ 440 g) ≈ 325 g (≈ 395 g) 7 6 62-61
01) UL approved ambient temperature: 50℃ Lock position
2 42 41 12 11 1
• Observe all ‘Safety Considerations’ for safe and proper operation to avoid hazards. This is only for reference, the actual product does not support all combinations. 02) R
 ated protection structure is for the switch body. Be cautious about preventing the head part from entering the foreign
42-11
materials such as dust and water.
• ᜸ symbol indicates caution due to special circumstances in which hazards may occur. For selecting the specified model, follow the Autonics website. SFDL-□C-□□□ 1 N.C./1 N.O. + 2 N.C.
Contact block 32-31

᜸ Warning
8 64 63 32 31 5
Failure to follow instructions may result in serious injury or death. SFDL - ❶ ❷ ❸ - ❹ ❺ ❻ Rated voltage/current for load
Resistive load: 1 A/120 VACᜠ, 0.22 A/125 VDCᜡ
Inductive load (IEC): AC-15 1 A/120 VACᜠ, DC-13 0.22 A/125 VDCᜡ
7 6 64-63

Inductive load (UL): C150, R150 Lock position

01. F
 ail-safe device must be installed when using the unit with machinery that may cause 2 42 41 12 11 1
serious injury or substantial economic loss. (e.g. nuclear power control, medical equipment, ❶ Lock/Release method ❹ Connection type Between the terminals of same polarity: 1.5 kV 42-11
ships, vehicles, railways, aircraft, combustion apparatus, safety equipment, crime/disaster M: Mechanical Lock/Solenoid Release No-mark: Terminal type Impulse dielectric strength Between the terminals of different polarity: 1.5 kV SFDL-□D-□□□ 2 N.C.+2 N.C.
32-31
prevention devices, etc.) S: Solenoid Lock/Mechanical Release C: Connector type Between each terminal and non-live part: 2.5kV 8 62 61 32 31 5
Failure to follow this instruction may result in personal injury, economic loss or fire. 7 6 62-61
Insulation resistance ≥ 100 MΩ (500 VDCᜡ megger)
02. System manager means followings; ❷ Contact ❺ Connection outlet specification
- a personnel who is fully aware of installation, setting, operation, and maintenance of the No-mark: 4-contct (connected) M20: M20 thread Contact resistance ≤ 200 mΩ Lock position
product 2 42 41 1
C: 4-contact (not connected) G1/2: G1/2 thread Electrical life cycle ≥ 100,000 operations (125 VACᜠ/1 A) 42-41
- a personnel who well observes standard/regulation/statute on the product by type of 1 N.C./1 N.O. + 4 22 21 3
machine the product installed in and nation/region the product used in 5: 5-contact Conditional short-circuit current 100 A SFDL-□CA-□□□ 22-21
❻ Release key type 1 N.C./1 N.O.
Machine user means a personnel who is appropriately trained about using machine by the 6: 6-contact 8 64 63 34 33 5 34-33
No-mark: Cross type Solenoid
system manager, so that machine user can operate the machine correctly. 7 6 64-63
System manager has duty to train the machine user about operation of the product. K: Special type Rated voltage 24 VDCᜡ, class 2
Supplying power: 0.26A Lock position
Machine user has to report directly to the system manager when unusual status has been 2 42 41 1
found while system is operating. ❸ Contact composition Current consumption
Normal: max. 0.2A (approx. 3 seconds after supplying power) 42-41
Failure to follow this instruction may result in personal injury, economic loss or fire. 4 22 21 3
Insulation class Class E SFDL-□CB-□□□ 2 N.C. + 1 N.C./1 N.O. 22-21
03. The product has to be installed, set, and combined with machine control system by the 4-contact 5-contact 6-contact
8 62 61 34 33 5 34-33
qualified system manager. Lock 1 N.C. / 1 N.O. + Lock 1 N.C. / 1 N.O. + Lock 2 N.C. /1 N.O. + 7 6
Failure to follow this instruction may result in personal injury due to unintended operation and A 62-61
Door 1 N.C. / 1 N.O. Door N.C. 2 / N.O. 1 Door 2 N.C. /1 N.O.
unstable detection. Lock position
04. Before using the product, check that function of the product operates as intended while
machine is turned off after installation.
B Lock N.C. 2 + Door N.C. 1 / N.O. 1 Lock N.C. 2 + Door N.C. 2 / N.O. 1 Lock N.C. 3 + Door N.C. 2/N.O. 1 Installation 2 42 41 1
4 22
42-41
21 3
Failure to follow this instruction may result in personal injury due to unintended operation and C Lock N.C. 1 / N.O. 1 + Door N.C. 2 Lock N.C. 1 / N.O. 1 + Door N.C. 3 Lock N.C. 2/N.O. 1 + Door N.C. 3 SFDL-□CC-□□□ 1 N.C./1 N.O. + 2 N.C. 22-21
unstable detection.
• The head of the switch can be rotated by loosening the four screws from th e corners of the 8 64 63 32 31 5
D Lock N.C. 2 + Door N.C. 2 Lock N.C. 2 + Door N.C. 3 Lock N.C. 3 + Door N.C. 3 32-31
05. Do not use the unit in the place where flammable/explosive/corrosive gas, high humidity, head and reinstalling the head in the desired orientation. 7 6 64-63
direct sunlight, radiant heat, vibration, impact, salinity, moisture, or steam, or dust may be • Be sure to install the switch with the minimum radius at a hinged door as shown in the table.
present. Lock position
2 42 41 1
Dimensions
Failure to follow this instruction may result in explosion or fire. Door hinge Operation Minimum radius 42-41
06. Do not disassemble or modify the unit. 4 22 21 3
key R1 R2 SFDL-□CD-□□□ 2 N.C.+2 N.C. 22-21
Failure to follow this instruction may result in personal injury or fire due to loss of safety function. R2 8 62 61 32 31 5 32-31
07. Do not defeat, tamper, modify, or bypass the switch and enter the door. • Unit: mm, For the detailed dimensions of the product, follow the Autonics web site. R1 SFD-KH 300 mm 300 mm 7 6
Failure to follow this instruction may result in personal injury. 62-61
08. Be cautious about the installing place of the operation key in order to protect worker from ■ Terminal type ■ Connector type SFD-KL 300 mm 300 mm
Lock position
hitting the operation key when the door is opened. SFD-KHR 300 mm 300 mm 2 42 41 12 11 1
Failure to follow this instruction may result in personal injury. Door hinge SFD-KLR 300 mm 300 mm 1 N.C./1 N.O. + 4 22 21 3
42-11
09. Do not use a head of other product. SFDL-□5A-□□□
8 11.5

8 11.5 22-21
4

2 N.C./1 N.O.
Failure to follow this instruction may result in personal injury or fire due to loss of safety function. 4 SFD-KLF 50 mm 300 mm 8 64 63 34 33 5 34-33
34.5

34.5

10. Install separate safety device to fix door closed, or door can be opened because of vibration SFD-KLF2 50 mm 300 mm 7 6 64-63
or weight of the door.
Failure to follow this instruction may result in personal injury. • Inspect the inserted operation key remains • Install the operation key within ±1 mm from Lock position
2 42 41 12 11 1
11. Check the installed status of the switch, operating status of the switch, and signs of damage, within the set zone (0.5 to 3 mm). the center of the operation key hole.
modification, tampering of the switch at the following situation and on a weekly basis. □39 □39 4 22 21 3
42-11
□30 □30 SFDL-□5B-□□□ 2 N.C. + 2 N.C./1 N.O. 22-21
- when operating the safety system at first ±1 mm ±1 mm 8 62 61 34 33 5
- when replacing component of the system 16.8 16.8 34-33
- when the system has not been operated for a long time Set zone: 0.5 to 3 mm 7 6 62-61
Failure to follow this instruction may result in personal injury due to malfunction of the product Lock position
and safety function. 2 42 41 12 11 1
12. Solenoid Lock/Mechanical Release type switch is locked with power connected and is 42-11
38.5

4 22 21 3
4
38.5
4

SFDL-□5C-□□□ 1 N.C./1 N.O. + 3 N.C.

31.5
31.5

unlocked without power. Be cautious that the switch can be unlocked before complete stop 22-21
of the machine when blackout occurs. 8 64 63 32 31 5 32-31
Failure to follow this instruction may result in personal injury. 7 6 64-63
13. Check ‘Connections’ before wiring.
10

10

Failure to follow this instruction may result in fire. Lock position

4.2
4.2
8

35
8

2 42 41 12 11 1
35
᜸ Caution
42-11
Failure to follow instructions may result in injury or product damage. • Recommended screw tightening torque • Cable gland specification and recommended SFDL-□5D-□□□ 2N.C. +3 N.C.
4 22 21 3
22-21
product
180

8 62 61 32 31 5
Screw Tightening torque 32-31
155

01. Use the unit within the rated specifications. Thread 7 6 62-61
Failure to follow this instruction may result in fire or product damage. Terminal screw 0.4 N.m MFR Model Cable Ø
spec
116.5

02. Since solenoid has polarity, wire cables and supply voltage ensuring correct polarity. Do not Lock position
Head mounting screw (M3) 0.7 to 0.9 N.m CP FCGL-G12B 4 - 8 mm 2 42 41 12 11 1
supply voltage above the rated voltage specification. G1/2 42-11
141.5

Failure to follow this instruction may result in fire or solenoid damage. Cable cover 0.5 to 0.7 N.m SYSTEM FCGL-G16B 7 - 12.3 mm 2 N.C./1 N.O. + 4 52 51 22 21 3
SFDL-□6A-□□□ 52-21
03. Use a dry cloth to clean the unit, and do not use water or organic solvent. 2 N.C./1 N.O.
Cable gland 2.7 to 3.3 N.m ST-M20X1.5 8 64 63 34 33 5 34-33
Failure to follow this instruction may result in fire. M20 LAPP 6 - 13 mm
04. Keep the door switch away from debris and tighten the screw securely when replacing the / 5311-1020 7 6 64-63
head. In case of using the cable gland with the 9 Lock position
Failure to follow this instruction may result in malfunction. mm screw thread or longer, a gap between
2 42 41 12 11 1
05. Keep the product away from metal chip, dust, and wire residue which might flow into the 42-11
unit. the switch and cable may affect the SFDL-□6B-□□□ 3 N.C. + 2 N.C./1 N.O.
4 52 51 22 21 3
52-21
Failure to follow this instruction may result in fire, product damage or malfunction. Ø25 protection structure. 8 62 61 34 33 5 34-33
06. Do not use metallic cable gland. 7 6 62-61
Failure to follow this instruction may result in electric shock due to the damage on the service
entrance. Ø25 Lock position
Release Key
2 42 41 12 11 1
07. Do not use the switch as a guard door stopper. Install separate mechanical stopper. 42-11
Failure to follow this instruction may result in product damage. SFDL-□6C-□□□ 2 N.C./1 N.O. + 3 N.C.
4 52 51 22 21 3
08. Carefully manage the spare operation key in order to prevent use of the key without 52-21
2

8 64 63 32 31 5
2

permission. Release key type Normal position Manual unlock position 32-31
Failure to follow this instruction may result in loss of safety function due to insertion of the spare 7 6 64-63
operation key. Lock position
09. Use only Autonics operation key. 2 42 41 12 11 1
Cross type
Failure to follow this instruction may result in product damage. 42-11
10. Install the operation key tightly within the range written in ‘Installation’ with welding, rivet, ■ Panel cut out SFDL-□6D-□□□ 3 N.C.+3 N.C.
4 52 51 22 21 3
52-21
or special bolt in order not to be easily released from the switch. 8 62 61 32 31 5 32-31
Failure to follow this instruction may result in product damage. 30 7 6 62-61
11. When it comes to the Solenoid Lock/Mechanical Release model, make it to be locked by 22
supplying power after the door is closed. Special type
Failure to follow this instruction result in malfunction, if the power is supplied when the door is
opened.
12. When changing the direction of the head, make sure that the cam inside the head does not • You can manually unlock the switch in the emergency situation such as blackout, when wiring,
rotate. 4-M4 before supplying power, or when testing operation of the switch.
Failure to follow this instruction result in malfunction.
10

13. Do not apply the power over 0.2 N·m on the release key and do not use tools that may apply • When using the release key, turn it to the marked position completely.
strong force, such as an electric screwdrivers. Otherwise (under 90˚), switch can be damaged or malfunction. 18, Bansong-ro 513Beon-gil, Haeundae-gu, Busan, Republic of Korea, 48002
Failure to follow this instruction may result in product damage. www.autonics.com | +82-2-2048-1577 | [email protected]
30