PROJECT:- MAJOR UPGRADATION OF SECUNDERABAD RAILWAY STATION

BOQ FOR WATER TREATMENT PLANT & PLUMBING PUMPS

WTP - 545 KLD FOR NORTH SIDE BUILDING & 363 KLD FOR SOUTH SIDE BUILDING

Rate Amount
S.NO. DESCRIPTION Unit Qty.
(Rs.) (Rs.)

A. SUB HEAD - I - WTP, WATER SUPPLY, DRAINAGE, PUMPS & EQUIPMENT

1 FILTER FEED PUMPS

Providing and fixing horizontical/vertical monobloc centrifugal pumping set. The
pumps shall be made of Casing cast-iron, Impellers shall be one-piece, zinc free
bronze and dynamically balanced Shaft for pumps with suffing boxes shall be of
stainless steel mechanical seal cast iron (C.I) volute and bronze impeller connected
to a IE3 induction motor suitable for 400/440 volts, 3 phase, 50 cycles A.C. supply
with 150 mm dia pressure gauge with gunmetal isolation cock, vibration eliminating
for each pump including necessary structual supports, clamps, bolts, nuts washers
and 1:2:4 plain cement concreate (PCC) foundations

For North Side Building

Considered Total Domestic Water - 545 KLD
No. of Working Hours - 12 Hrs.
1.1 Filter Feed pump ( 1 Set = 2 working + 1 standby) (North Side Building)
Location - Plumbing Plant Room
Capacity 380 LPM (Each Pump)
Head 35 m
HP/kW Load 4.9 HP or As required (Each Pump) Set 1

For South Side Building

Considered Total Domestic Water - 363 KLD
No. of Working Hours - 12 Hrs.
1.2 Filter Feed pump ( 1 Set = 2 working + 1 standby) (South Side Building)
Location - Plumbing Plant Room
Capacity 250 LPM (Each Pump)
Head 35 m
HP/kW Load 3.25 HP or As required (Each Pump) Set 1

Plumbing Plant Room - Railway Station (Assumed for filling up two trains of 24
coach simultaneously)
No. of Working minutes - 5 Min.
1.3 Coach Filling pump ( 1 Set = 3 working + 1 standby)
Location - Plumbing Plant Room
Capacity 3460 LPM (Each Pump)
Head 60 m
HP/kW Load 77.0 HP / 57.45 kW (Each Pump) Set 1

Page 1
 Rate Amount
S.NO. DESCRIPTION Unit Qty.
(Rs.) (Rs.)
2 Variable Frequency Drive System:
Vertical centrifugal (direct coupled) pumps cast-iron Casing material, Impellers shall
be one-piece, zinc free bronze and dynamically balanced Shaft for pumps with
suffing boxes shall be of stainless steel with IE3 motor mounted on a common M.S.
structural frame work, including common suction header with flange for inlet
connection, common outlet, header with flange for outlet connections and
interconnecting piping with isolating valves, non-return valves, pressure gauges with
isolation cock etc.
Precharged diaphragm pressure vessel FRP of suitable size (minimum 400 Ltrs
capacity (approx.) or as per manufacturer calculation / recommendation) for the
system mentioned below with charging connection, connected to outlet header with
necessary flanges, gaskets, isolating, valves, nuts/bolts etc. complete.
Fully automatic control panel including starters, instruments, incoming isolator, level
control for low water gaurd for pumps, microprocess based PLC, variable frequency
drive (VFD) and all controls, pressure transmitter, low and high system pressure
switch with alarm auto/manual selector switches, interconnecting power /control
cabling etc. all accessories which are required to complete the system for working
conditions as per specifications.
Hydropneumatic system as described above and as under given capacities:

For North Side Building

Considered Total Domestic Water - 545 KLD
No. of Working Hours - 12 Hrs.
2.1 Cold Water Supply Pumps : ( 1 set = 2 W + 1 SB) (North Side Building)
Location - Plumbing Plant Room
Capacity 380 LPM (Each Pump)
Head 60 m
HP/kW Load 8.5 HP or As required (Each Pump) Set 1

For South Side Building

Considered Total Domestic Water - 363 KLD
No. of Working Hours - 12 Hrs.
2.2 Cold Water Supply Pumps : ( 1 set = 2 W + 1 SB) (South Side Building)
Location - Plumbing Plant Room
Capacity 250 LPM (Each Pump)
Head 65 m
HP/kW Load 6.1 HP or As required (Each Pump) Set 1

Supplying, installing, testing and commissioning single stage, submersible centrifugal

pumps of closed coupled construction with SS-304 casing, SS-304 Impellar, SS-304
shaft connected to a fully submersible water/oil cooled motor suitable to operate with
380-415 volts 3 phase 50 cycles AC power supply with class F insulation and built -in
3 temperature protection, pump connector unit with rubber diaphram & bend, vertical
discharge pipe, guide pipe, stainless steel chain/rope, water -proof power cable and
level controller complete in all respects for fixed installation.

For Sump Pump (1 Working + 1 Standby) For Drainage (Plant Room) (North Side
3.1
Building)
Discharge 380 lpm
Head 15 m
HP/kw Load 2.2 hp (approx.) Set 1

For Sump Pump (1 Working + 1 Standby) For Drainage (Plant Room) (South Side
3.2
Building)
Discharge 250 lpm
Head 15 m

Page 2
 Rate Amount
S.NO. DESCRIPTION Unit Qty.
(Rs.) (Rs.)
HP/kw Load 1.4 hp (approx.) Set 1

Supplying, installing, testing and commissioning single stage, submersible centrifugal

pumps of closed coupled construction with SS-304 casing, SS-304 Impellar, SS-304
shaft connected to a fully submersible water/oil cooled motor suitable to operate with
380-415 volts 3 phase 50 cycles AC power supply with class F insulation and built -in
temperature protection, pump connector unit with rubber diaphram & bend, vertical
4
discharge pipe, guide pipe, stainless steel chain/rope, water -proof power cable, The
item shall include with wiring connection between panel & pumps and level
controller complete in all respects for fixed installation.

For Sump Pump (1 Working + 1 Standby) For Drainage (Station Building Supply at
4.1
PRS)
(Pumps to be suitable to handle solids upto 10-15 mm size)
Discharge 420 lpm
Head 75 m
HP/kw Load 11.6 hp (approx.) Set 1

Electric Panel For Basement Drainage Sump Pump (Station Building Supply at
a
PRS)

One incoming main MCCB unit of 32 amps rating.

All switch gear/panels shall be suitable for 25 KA rating.
Copper bus bar is separate chamber fully taped of 32 amps capacity.
Two MCB units of 25 amps (1w+1sb )
Two fully automatic DOL starters with push buttons and on/off indicating lights.
One rotary duty selector switch
Two manual/auto/off switches.
Two single phasing presenters.
One panel type voltmeter with rotary selector switch for reading voltage between
phases.
Two ampere meters one for each motor.
Three neon phase indicating lights on the incoming mains.
Space for one liquid level controllers.

All internal wiring colour coded from incoming mains to various switchgear, starters,
meters, indicating lamps and bus bar with a changeover facility to run each pump
alternatively with an alarm bell in case of both pump’s running at one time.
Switchegear offered must be compatible with the HP of the motors offered.
Motor control centre as described above Set 1

4.2 For Sump Pump (1 Working + 1 Standby) For Drainage (South Side Basement)
(Pumps to be suitable to handle solids upto 10-15 mm size)
Discharge 500 lpm
Head 30 m
HP/kw Load 5.6 hp (approx.) Set 3

a Electric Panel For Basement Drainage Sump Pump (South Side Basement)

One incoming main MCCB unit of 25 amps rating.

All switch gear/panels shall be suitable for 25 KA rating.
Copper bus bar is separate chamber fully taped of 25 amps capacity.
Two MCB units of 16 amps (1w+1sb )
Two fully automatic DOL starters with push buttons and on/off indicating lights.

One rotary duty selector switch

Two manual/auto/off switches.
Two single phasing presenters.
One panel type voltmeter with rotary selector switch for reading voltage between
phases.
Two ampere meters one for each motor.
Three neon phase indicating lights on the incoming mains.
Space for one liquid level controllers.

All internal wiring colour coded from incoming mains to various switchgear, starters,
meters, indicating lamps and bus bar with a changeover facility to run each pump
alternatively with an alarm bell in case of both pump’s running at one time.
Switchegear offered must be compatible with the HP of the motors offered.
Motor control centre as described above Set 3

4.3 For Sump Pump (1 Working + 1 Standby) For Drainage (North Side Basement)

Page 3
 Rate Amount
S.NO. DESCRIPTION Unit Qty.
(Rs.) (Rs.)
(Pumps to be suitable to handle solids upto 10-15 mm size)
Discharge 300 lpm
Head 30 m
HP/kw Load 3.4 hp (approx.) Set 4

Electric Panel For Basement Drainage Sump Pump (North Side Basement)
a

One incoming main MCCB unit of 25 amps rating.

All switch gear/panels shall be suitable for 25 KA rating.
Copper bus bar is separate chamber fully taped of 25 amps capacity.
Two MCB units of 16 amps (1w+1sb )
Two fully automatic DOL starters with push buttons and on/off indicating lights.

One rotary duty selector switch

Two manual/auto/off switches.
Two single phasing presenters.
One panel type voltmeter with rotary selector switch for reading voltage between
phases.
Two ampere meters one for each motor.
Three neon phase indicating lights on the incoming mains.
Space for one liquid level controllers.

All internal wiring colour coded from incoming mains to various switchgear, starters,
meters, indicating lamps and bus bar with a changeover facility to run each pump
alternatively with an alarm bell in case of both pump’s running at one time.
Switchegear offered must be compatible with the HP of the motors offered.
Motor control centre as described above Set 4

4.4 For Sump Pump (1 Working + 1 Standby) For Drainage (MLCP Basement)
(Pumps to be suitable to handle solids upto 10-15 mm size)
Discharge 1150 lpm
Head 80 m
HP/kw Load 10.6 hp (approx.) Set 1

a Electric Panel For Basement Drainage Sump Pump (MLCP Basement)

One incoming main MCCB unit of 32 amps rating.

All switch gear/panels shall be suitable for 25 KA rating.
Copper bus bar is separate chamber fully taped of 32 amps capacity.
Two MCB units of 25 amps (1w+1sb )
Two fully automatic DOL starters with push buttons and on/off indicating lights.
One rotary duty selector switch
Two manual/auto/off switches.
Two single phasing presenters.
One panel type voltmeter with rotary selector switch for reading voltage between
phases.
Two ampere meters one for each motor.
Three neon phase indicating lights on the incoming mains.
Space for one liquid level controllers.

All internal wiring colour coded from incoming mains to various switchgear, starters,
meters, indicating lamps and bus bar with a changeover facility to run each pump
alternatively with an alarm bell in case of both pump’s running at one time.
Switchegear offered must be compatible with the HP of the motors offered.
Motor control centre as described above Set 1

For Sump Pump (1 Working + 1 Standby) For Sewerage (South Side Basement) For
4.5
Solid handling capacity upto 40mm
Discharge 220 lpm
Head 25 m
HP/kw Load 2.1 hp (approx.) Set 1

Electric Panel For Basement Sewerage Sump Pump (North Side Basement)
a

One incoming main MCCB unit of 25 amps rating.

All switch gear/panels shall be suitable for 25 KA rating.
Copper bus bar is separate chamber fully taped of 25 amps capacity.
Two MCB units of 16 amps (1w+1sb )
Two fully automatic DOL starters with push buttons and on/off indicating lights.

Page 4
 Rate Amount
S.NO. DESCRIPTION Unit Qty.
(Rs.) (Rs.)
One rotary duty selector switch
Two manual/auto/off switches.
Two single phasing presenters.
One panel type voltmeter with rotary selector switch for reading voltage between
phases.
Two ampere meters one for each motor.
Three neon phase indicating lights on the incoming mains.
Space for one liquid level controllers.

All internal wiring colour coded from incoming mains to various switchgear, starters,
meters, indicating lamps and bus bar with a changeover facility to run each pump
alternatively with an alarm bell in case of both pump’s running at one time.
Switchegear offered must be compatible with the HP of the motors offered.
Motor control centre as described above Set 1

For Sump Pump (1 Working + 1 Standby) For Sewerage (North Side Basement
4.6
Right Side) For Solid handling capacity upto 40mm
Discharge 190 lpm
Head 20 m
HP/kw Load 2.1 hp (approx.) Set 1

Electric Panel For Basement Sewerage Sump Pump (North Side Basement
a
Right Side)

One incoming main MCCB unit of 25 amps rating.

All switch gear/panels shall be suitable for 25 KA rating.
Copper bus bar is separate chamber fully taped of 25 amps capacity.
Two MCB units of 16 amps (1w+1sb )
Two fully automatic DOL starters with push buttons and on/off indicating lights.

One rotary duty selector switch

Two manual/auto/off switches.
Two single phasing presenters.
One panel type voltmeter with rotary selector switch for reading voltage between
phases.
Two ampere meters one for each motor.
Three neon phase indicating lights on the incoming mains.
Space for one liquid level controllers.

All internal wiring colour coded from incoming mains to various switchgear, starters,
meters, indicating lamps and bus bar with a changeover facility to run each pump
alternatively with an alarm bell in case of both pump’s running at one time.
Switchegear offered must be compatible with the HP of the motors offered.
Motor control centre as described above Set 1

For Sump Pump (1 Working + 1 Standby) For Sewerage (North Side Basement
4.7
South Side) For Solid handling capacity upto 40mm
Discharge 230 lpm
Head 20 m
HP/kw Load 1.8 hp (approx.) Set 1

Electric Panel For Basement Sewerage Sump Pump (North Side Basement
a
South Side)

One incoming main MCCB unit of 25 amps rating.

All switch gear/panels shall be suitable for 25 KA rating.
Copper bus bar is separate chamber fully taped of 25 amps capacity.
Two MCB units of 16 amps (1w+1sb )
Two fully automatic DOL starters with push buttons and on/off indicating lights.

One rotary duty selector switch

Two manual/auto/off switches.
Two single phasing presenters.
One panel type voltmeter with rotary selector switch for reading voltage between
phases.
Two ampere meters one for each motor.
Three neon phase indicating lights on the incoming mains.
Space for one liquid level controllers.

All internal wiring colour coded from incoming mains to various switchgear, starters,
meters, indicating lamps and bus bar with a changeover facility to run each pump
alternatively with an alarm bell in case of both pump’s running at one time.
Switchegear offered must be compatible with the HP of the motors offered.

Page 5
 Rate Amount
S.NO. DESCRIPTION Unit Qty.
(Rs.) (Rs.)
Motor control centre as described above Set 1

5 MULTIGRADE PRESSURE SAND FILTER: (For Domestic Water)

Location - Plumbing Plant Room
Supply, installation, testing & commissioning of vertical self supporting multi grade
pressure filter (MGF) (Dual media filter) fabricated from MS sheet as per IS Code,
pressure gauges at inlet & outlet, sample cock, air vent valve with piping, GI face
piping distribution pipe with diffuser on top, CI butterfly valves and all accessories,
with initial charge of filter media for filter, painting inside with food grade epoxy paint
and outside with two coat of red oxide primer and two or more coat of synthetic
enamel paint complete with bypass arrangement including piping and valves (3 Nos.)
of required size.

For North Side Building

Considered Total Domestic Water - 545 KLD
No. of Working Hours - 12 Hrs.
a Capacity/Flow rate : 45.6 M3/hr ( North Side Building )
Filtration rate/velocity : 18-20 M3/M2/hr
Max. operating pressure : 3.5 kg/Sq.cm
Test pressure : 5.5 kg/Sq.cm
Suggested diameter : 1700 mm Each 1

For South Side Building

Considered Total Domestic Water - 363 KLD
No. of Working Hours - 12 Hrs.
b Capacity/Flow rate : 30.0 M3/hr ( For South Side Building )
Filtration rate/velocity : 18-20 M3/M2/hr
Max. operating pressure : 3.5 kg/Sq.cm
Test pressure : 5.5 kg/Sq.cm
Suggested diameter : 1400 mm Each 1

6 ACTIVATED CARBON FILTER: (For Domestic Water)

Location - Plumbing Plant Room
Supply, installation, testing & commissioning vertical self supporting Activated
Carbon Filter (ACF) fabricated from M.S. Sheet as per IS Code, pressure gauge at
inlet & outlet, sample cock, GI face piping, C.I. Butterfly valve and all accessories, air
vent valve with piping, with initial charge of filter media for activated carbon filter,
painting inside with epoxy paint and outside with two coat of synthetic enamel paint
complete with bypass arrangement including piping, CI Valves (3 Nos.) of required
size.

For North Side Building

Considered Total Domestic Water - 545 KLD
No. of Working Hours - 12 Hrs.
a Capacity/Flow rate : 45.6 M3/hr ( North Side Building )
Filtration rate/velocity : 18-20 M3/M2/hr
Max. operating pressure : 3.5 kg/Sq.cm
Test pressure : 5.5 kg/Sq.cm
Suggested diameter : 1700 mm Each 1

For South Side Building

Considered Total Domestic Water - 363 KLD
No. of Working Hours - 12 Hrs.
b Capacity/Flow rate : 30.0 M3/hr ( For South Side Building )
Filtration rate/velocity : 18-20 M3/M2/hr
Max. operating pressure : 3.5 kg/Sq.cm
Test pressure : 5.5 kg/Sq.cm
Suggested diameter : 1400 mm Each 1

Supplying, installing, testing and commissioning electronic chlorine solution dosing

system comprising of F.R.P/ chemical grade HDPE solution tank of 200 litres
7 capacity electronic dosing pump of capacity 0-6 LPH against 4.5 Kg/Sq.cm dosing
valves, flexible teflon tube pipes etc. complete for dosing of chlorine solution into
water on line.
7.1 Chlorine Dosing For North Side Building Each 1
7.2 Chlorine Dosing For South Side Building Each 1

Page 6
 Rate Amount
S.NO. DESCRIPTION Unit Qty.
(Rs.) (Rs.)
Supplying, installing, testing & commissioning of ultravoilet dis-infection unit. The unit
shall have over 99.9 % bacterial reduction from inlet to outlet. The dis-infection
chamber shall be constructed of SS 316L on all welted parts. The UV lamp shall be
8 of low pressure mercury vapour type with hard glass enclosure, the sockets shall be
water tight & vibration resistant. The lamp life shall be rated for 6000 hours. The unit
shall be complete with temperature safety control and lamp out alert circuit.

The UV unit shall have with reactor, cabinet housing, cabinet cooling, treatment
chamber, electrical panel, temperature safety control, lampout alert. The UV Dosage
should be > 30,000 uW – Sec / sq.cm. The lamps should be selected based upon
the flow requirement of respective unit.
8.1 Flow rate - 45.6 m3/hr (For North Side Building) No 1
8.2 Flow rate - 30 m3/hr (For South Side Building) No 1

Supply, installation, testing and commissioning of Digital Turbine Type flow meter
9
with online sensor and cable at WTP outlet for flow monitoring.
9.1 Flow rate - 45.6 m3/hr (For North Side Building) No 1
9.2 Flow rate - 30 m3/hr (For South Side Building) No 1

Supplying, installing, testing and commissioning of pH Correction dosing system (for

domestic water treatment plant) consisting of one HDPE tank of 100 litres capacity
with a positive displacement diphragm dosing pump having variable flowrate of 0-6
10 lph. The motor shall be suitable for operation at 240 V / single phase / 50 Hz. Supply.
The pump shall be supplied complete with necessary polypropylene piping, valves,
strainers, low level switch and injection fittings.
10.1 Flow rate - 45.6 m3/hr (For North Side Building) No 1
10.2 Flow rate - 30 m3/hr (For South Side Building) No 1

Supplying, installing, testing and commissioning of pH Controller with meter, sensor

11 and cable for monitoring and controlling online pH ranging between 0 to 14.

11.1 Flow rate - 45.6 m3/hr (For North Side Building) No 1

11.2 Flow rate - 30 m3/hr (For South Side Building) No 1

Providing and fixing mild steel (MS) puddle flanges of required size with 5mm thick
12 mild steel (MS) plate including necessary welding as per details shown on drawings
and directions of Engineer-in-charge for water tanks.
12.1 25mm dia (4mm wall thickness) Each 16
12.2 50mm dia (4mm wall thickness) Each 4
12.3 80mm dia (4mm wall thickness) Each 8
12.4 100mm dia (4mm wall thickness) Each 20
12.5 150mm dia (4mm wall thickness) Each 18

Supply, installation, testing & commissioning of Hot dipped galvanised 'Y' Strainer of
13
following sizes as per specification:
13.1 100 mm dia Each 4
13.2 150mm dia Each 2

Supplying, assembly, erection, testing and commissioning of magnetic level sensors

and controllers, Chlorinated Polyvinyl Chloride (CPVC) probe tube, PP actuating
float and all other equipment required for the performance of the system to the
satisfaction of the engineer in charge complete including providing and fixing wiring
14 from control junction box near the Under Ground tank to probes of required length, Job 14
interconnection wiring between level controller and the concerned contactor in the
starter panel as required. Level of all tanks (Under Ground and overhead tank) will
be included in this item. The level controller will perform the following functions.

To switch on the pumps when the level of water in the supply water tank is low and to
cut off the pump when the level in the recieving water tank is high and switch off the
pumps when the level of water in the supply water tank is low .
To indicate 5 levels of water in all tanks through a control panle with LEDs
To start the pumps in a cyclic order.
The system shall be complete to ensure automatic quotation of pump in accordance
to water level in respective tanks.

Supply, fixing, testing and commissioning of Site Tube (of 3.0 - 5 M) with isolation
15 valve at top and bottom demarcation on tube for making the installation of level Each 14
indication on the RCC water tank complete.

Providing, fixing, testing & commissioning of 100 mm dia Burden type, Stainless
16 Steel dial type pressure gauge including brass isolation valve and pipe having Each 14
caliberation of 0-16 Kg/cm2.

Page 7
 Rate Amount
S.NO. DESCRIPTION Unit Qty.
(Rs.) (Rs.)
Providing, laying, testing & commissioning of 'C' class Heavy duty G.I. pipe
conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers,
17 nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable
clamp/support frame and painting with two or more coats of synthetic enamel paint of
required shade complete as required :
17.1 65mm dia Meter 80
17.2 80mm dia Meter 60
17.3 100 mm dia Meter 65
17.4 150 mm dia Meter 50

Providing and fixing gun metal gate valve with C.I. wheel of approved quality
18 Each
(screwed end) :
a 40 mm nominal bore Each 4
b 50 mm nominal bore Each 15
c 65 mm nominal bore Each 16
d 80 mm nominal bore Each 10
e 100 mm nominal bore Each 10

Supplying, Installation, testing & commissioning complete testing kit with all
19 chemicals complete suitable for conducting test on water quantity. The test kit shall L.S 2
be suitable for measuring, TDS, PH, hardness, iron content etc.

Providing and fixing Butterfly valve Rated for PN16 pressure rating including rubber
20
gasket, flanges, nuts, bolts, washers & painting complete as required.
20.1 50 mm dia Nos. 10
20.2 65 mm dia Nos. 20
20.3 80 mm dia Nos. 8
20.4 100 mm dia Nos. 4
20.5 150 mm dia Nos. 4

Providing & fixing C.I. dual plate type check valve tested to a pressure of 15Kg/sqcm.
21 Including rubber gasket, flanges, union, nuts, bolts, washers & painting complete as
required.
21.1 50 mm dia Nos. 6
21.2 65 mm dia Nos. 8
21.3 80 mm dia Nos. 6
21.4 100 mm dia Nos. 6
21.5 150 mm dia Nos. 6

22 VIBRATION ELIMINATORS :
Providing, fixing, testing & commissioning of rubber neoprene lined style arch
vibration eliminators suitable pressure.
22.1 Pressure Rating PN 16 :
22.2 40 mm dia Each R.O.
22.3 50 mm dia Each 4
22.4 65 mm dia Each 6
22.5 80 mm dia Each 6
22.6 100 mm dia Each 4
22.7 150 mm dia Each 4

Supply, installation, testing and commissioning of tanker inlet connection complete

with 80 mm dia GI inlet piping, hose inlet connection, MS cabinet enclosure (epoxy
23 painted after fabrication), pad locking arrangement, inlet flexible hose complete with Nos. 2
all necessary arrangement.

ELECTRIC PANEL FOR WATER SUPPLY PUMPS AT PLUMBING PLANT ROOM

24
FOR NORTH SIDE BUILDING
Design, fabrication, assembling, wiring, supply, installation, testing and
commissioning of control panels for filter feed pump, hydropneumatic system &
Sump pump fabricated out of 14 gauge CRCA sheet steel in cubicle
compartmentised, free standing floor mounted, with a base channel of 100x 50 x 6
mm MS channel dust and vermin proof with reinforcement of suitable size angle iron
channel sections and or flats wherever necessary 3mm thick cable gland plates shall
be provided on top as well as at the bottom of the panels. Panels shall be treated
with seven tank process before painting as per specifications and a final approved
shade of powder coated paint 2 Nos earthing terminals shall be provided for all
distribution panels. Panels shall be suitable for 415 V 3 phase 4 wire, 50 HZ supply
system, switchboard with IP42 protection with hinged and lockable doors, Lifting
hooks shall also be provided in case of large panels. Control panel included with
earthing pit itself. Approval shall be taken for each panel in the form of shop
drawings before fabrication. Galvanized hard wares with Zinc passivation shall be
used in fabrication of panels. ( Pump room panel)(Including earthing).

Page 8
 Rate Amount
S.NO. DESCRIPTION Unit Qty.
(Rs.) (Rs.)
Incoming
1 No. - 630A 4P ATS
1 No. - 630A 4P MCCB of fault breaking capacity 25 kA (Ics = Icu upto 415V), fitted
with interlocked door, automatic safety shutters, mechanical ON/OFF and
service/test/isolated position indicators and frame earthing contact, conforming to IS-
13947-2 1993 as amended up-to-date complete with following accessories for each
MCCB.
Dual core calibrated digital Multifunctional meter of class 1.0 to record demand
(KVA), energy (KWH & KVAH), power factor, current (in each phase and the neutral),
voltage (between phases and between each phase and neutral) and 3 Nos. dual core
CT of A Class 1.0 accuracy and 15 VA burden.
Following indicating lamps and push buttons for each MCCB with back up 2A SP
MCB .
3 No. Phase indicating Lamps .
Indicating Lamps for the following;
Bus Bar
630 Amp. 25 kA, TPN Copper Bus Bar
One No. 630 amps 4P incoming MCCB complete with the following:
1 No. 0-500 volts 96x96 sq. mm ammeter with selector switch and fuses. (1 set).
1 No. 0-630 amps 96x96sq.mm ammeter with 630/5 amps ratio CT's and selector
switch.
Over voltage and under voltage tripping machanism for persistent voltage fluctations
of more than ±10% of the rated voltage for more than 5 minutes. (1set)

Phase indicating lamps with toggle switches.

Indication lamps for ON/OFF/TRIP status of motors.
Copper bus bar of 630 amps for three phase and neutral.
Outgoing Feeders/Starters.
16 amps TP MCCB with Dol starter each suitable 5.0 HP filter feed pumps (3 Nos).

4 No Fully Star Delta starters suitable for 77 H.P. Pump Motor with over load
relay,contractors, time, push buttons, Auto/Manual selector switch and phase
indication light with MCB Ammeter (0- 160 Amp) with selector switch an CT’s of ratio
160/5A, 5VA class 1.0 and including 160A MCCB complete; as required .(for coach
filling transfer pumps )
25 amps TP MCCB with Dol starter each suitable 8.5 HP hydropneumatic pumps (3
Nos) (Only connection to inbuilt panel of Domestic water hydropneumatic system)

16 amps TP MCCB With Dol starter each suitable for 2.0 HP sump pumps in Plant
Room (2 Nos)
32 amps TP MCCB With Dol starter each suitable for 16.5 HP sump pumps Coach
Watering (2 Nos)
6A DP MCB with ON/OFF selector switch for Dosing Pumps - 1 No.
16A DP MCB with ON/OFF Selector switch for UV - 1 No.
MCB for PH Controller, Flow Meter
Spares
160 amps TPN MCCB - 2 Nos.
25 amps TPN MCCB - 1 Nos.
32 amps TPN MCCB - 1 Nos.
16 amps TPN MCCB - 2 Nos.
Note :
All switch gear/panels shall be suitable for 25 KA rating.
All outgoing will have 96 sq. mm size ammeter and CT.
All starter will have spare 25/16/32/160 amps 230 V coil auxiliary contractor for
building Automation system.
All starter units for pumps to be provided with 3 level liquid level contractor.
Lamps.
All pumps to be provided with duty selector switch.
All pumps to be provided with sequence timer 220/440 V AC/DC and alternate
working of pumps between 6 to 8 hours or alternate use of pumps after one service
in sequence.
All pumps to be provided with over load relay.
All starter to be provided with single phase preventor.
Necessary cable alleys for space switches, level controller internal wiring and copper
earthing of all equipment shall also be included. All switch gears/control gears shall
be motor duty rating.
Provisions of BMS system for pumps to be included in electrical control panel. The
panel manufacuturer shall include the following:
PF contact at Pumps Starter panels for Pumps Start/Stop Command for all pumps
indicated above.

Page 9
 Rate Amount
S.NO. DESCRIPTION Unit Qty.
(Rs.) (Rs.)
PF contact at Pumps Starter panels for Pumps Run Status for all pumps indicated
above.
PF contact at Pumps Starter panels for AUTO/MANUAL switches for all pumps
indicated above.
PF contact at Pumps Starter panels for over load relay trip signals for all pumps
indicated above.
24.1 Cabling from BMS system to this panels will be done by BMS contractor. Set 1

Providing and fixing Electrical Cabling for all equipment feed supplies & Copper
25 Lot 1
flexible for control cabling including GI wires & strips for earthing .

Providing and fixing GI Cable Trays and supports of suitable sizes for all equipment
26 Lot 1
feed supplies.

ELECTRIC PANEL FOR WATER SUPPLY PUMPS AT PLUMBING PLANT ROOM

27
FOR SOUTH SIDE BUILDING
Design, fabrication, assembling, wiring, supply, installation, testing and
commissioning of control panels for filter feed pump, hydropneumatic system &
Sump pump fabricated out of 14 gauge CRCA sheet steel in cubicle
compartmentised, free standing floor mounted, with a base channel of 100x 50 x 6
mm MS channel dust and vermin proof with reinforcement of suitable size angle iron
channel sections and or flats wherever necessary 3mm thick cable gland plates shall
be provided on top as well as at the bottom of the panels. Panels shall be treated
with seven tank process before painting as per specifications and a final approved
shade of powder coated paint 2 Nos earthing terminals shall be provided for all
distribution panels. Panels shall be suitable for 415 V 3 phase 4 wire, 50 HZ supply
system, switchboard with IP42 protection with hinged and lockable doors, Lifting
hooks shall also be provided in case of large panels. Control panel included with
earthing pit itself. Approval shall be taken for each panel in the form of shop
drawings before fabrication. Galvanized hard wares with Zinc passivation shall be
used in fabrication of panels. ( Pump room panel)(Including earthing).

Incoming
1 No. - 100A 4P ATS
1 No. - 100A 4P MCCB of fault breaking capacity 25 kA (Ics = Icu upto 415V), fitted
with interlocked door, automatic safety shutters, mechanical ON/OFF and
service/test/isolated position indicators and frame earthing contact, conforming to IS-
13947-2 1993 as amended up-to-date complete with following accessories for each
MCCB.
Dual core calibrated digital Multifunctional meter of class 1.0 to record demand
(KVA), energy (KWH & KVAH), power factor, current (in each phase and the neutral),
voltage (between phases and between each phase and neutral) and 3 Nos. dual core
CT of A Class 1.0 accuracy and 15 VA burden.
Following indicating lamps and push buttons for each MCCB with back up 2A SP
MCB .
3 No. Phase indicating Lamps .
Indicating Lamps for the following;
Bus Bar
100 Amp. 25 kA, TPN Copper Bus Bar
One No. 100 amps 4P incoming MCCB complete with the following:
1 No. 0-500 volts 96x96 sq. mm ammeter with selector switch and fuses. (1 set).
1 No. 0-100 amps 96x96sq.mm ammeter with 100/5 amps ratio CT's and selector
switch.
Over voltage and under voltage tripping machanism for persistent voltage fluctations
of more than ±10% of the rated voltage for more than 5 minutes. (1set)

Phase indicating lamps with toggle switches.

Indication lamps for ON/OFF/TRIP status of motors.
Copper bus bar of 100 amps for three phase and neutral.
Outgoing Feeders/Starters.
16 amps TP MCCB with Dol starter each suitable 3.25 HP filter feed pumps (3 Nos).

25 amps TP MCCB with Dol starter each suitable 6.1 HP hydropneumatic pumps (3
Nos) (Only connection to inbuilt panel of Domestic water hydropneumatic system)

16 amps TP MCCB With Dol starter each suitable for 2.0 HP sump pumps (2 Nos)

6A DP MCB with ON/OFF selector switch for Dosing Pumps - 1 No.

16A DP MCB with ON/OFF Selector switch for UV - 1 No.
MCB for PH Controller, Flow Meter
Spares
25 amps TPN MCCB - 1 Nos.

Page 10
 Rate Amount
S.NO. DESCRIPTION Unit Qty.
(Rs.) (Rs.)
16 amps TPN MCCB - 2 Nos.
Note :
All switch gear/panels shall be suitable for 25KA rating.
All outgoing will have 96 sq. mm size ammeter and CT.
All starter will have spare 25/16 amps 230 V coil auxiliary contractor for building
Automation system.

Page 11
 Rate Amount
S.NO. DESCRIPTION Unit Qty.
(Rs.) (Rs.)
All starter units for pumps to be provided with 3 level liquid level contractor.
Lamps.
All pumps to be provided with duty selector switch.
All pumps to be provided with sequence timer 220/440 V AC/DC and alternate
working of pumps between 6 to 8 hours or alternate use of pumps after one service
in sequence.
All pumps to be provided with over load relay.
All starter to be provided with single phase preventor.
Necessary cable alleys for space switches, level controller internal wiring and copper
earthing of all equipment shall also be included. All switch gears/control gears shall
be motor duty rating.
Provisions of BMS system for pumps to be included in electrical control panel. The
panel manufacuturer shall include the following:
PF contact at Pumps Starter panels for Pumps Start/Stop Command for all pumps
indicated above.
PF contact at Pumps Starter panels for Pumps Run Status for all pumps indicated
above.
PF contact at Pumps Starter panels for AUTO/MANUAL switches for all pumps
indicated above.
PF contact at Pumps Starter panels for over load relay trip signals for all pumps
indicated above.
27.1 Cabling from BMS system to this panels will be done by BMS contractor. Set 1

Providing and fixing Electrical Cabling for all equipment feed supplies & Copper
28 Lot 1
flexible for control cabling including GI wires & strips for earthing .

Providing and fixing GI Cable Trays and supports of suitable sizes for all equipment
29 Lot 1
feed supplies.

Note: Actual requiment of MGF and ACF shall be design only after the water quality
report.

Total C/F to Summary

Page 12