DUAL TECHNOLOGY SENSOR
(PIR + Microwave)
Outdoor use
INSTALLATION MANUAL
1. DESCRIPTION
Dual Technology Sensor (PIR + Microwave).
AND operation in the prevention of "false alarms".
IP65 (indoor and outdoor).
Mount directly to the wall or by "L" bracket.
Sensibility adjustable PIR with angular aperture of about 6 °.
Microwave K-band 24 GHz.
IR range adjustable from 0 to 12m.
MW range adjustable from 0 to 12m.
Function and output ANTI-MASKING for infrared and microwave.
High immunity to false alarms.
RF immunity up to 2Ghz.
Pet Immunity.
Small size (135mm x 33mm x 40mm)
Processing digital signals of PIR and MW.
Security Function.
Digital Filter 100Hz.
Temperature Autocompensation.
Environmental Autocompensation.
Operativity Self scanning of PIR technology.
Operativity Self scanning of MW technology.
Tamper output combined anti- removal and anti-tear.
Dip-Switch programming.
Politec S.r.l. | Man NAT– Ver. 1.5 2
NAT MOTHERBOARD
1 4
10-30 Vcc – GND
2 5 1 POWER SUPPLY Pay attention to the
polarity.
ANTI-MASK Negative always
3 2 (anti open collector opens in the event of
negative) masking.
the system is
SBY
3 inhibited if an + is
(positive input)
connected
6 TAMPER
It opens in case of
4 (N.C. tamper
sensor tampering.
7 output)
ALARM It opens in case of
5
(N.C. alarm output) detection MW+IR.
TAMPER
8 9 BUTTONS If they get open give
6
(anti-removal and the opening of N.C.
anti-tear)
System
12 7 DIP SWITCHES
10 configuration.
rotating in clockwise
8 TRIMMER MW increases the range
(sensibility) of MW.
11
rotating in clockwise
9 TRIMMER IR increases the range
(sensibility) of IR.
13 lit up when there is a
RED LED
10 general alarm, if
(ALARM)
enabled.
lit up when there is a
ORANGE LED
11 PIR alarm, if
(PIR)
enabled.
lit up when there is a
GREEN LED
12 Microwave alarm, if
(MW)
enabled.
14
MICROWAVE Detection sensor
13
24GHZ MW.
PYROELECTRIC
14 Detection sensor IR.
SENSOR
Politec S.r.l. | Man NAT– Ver. 1.5 3
2. MOUNTING
The mounting of the NAT can occur in two modes or directly to the wall through the plate or "L"
through the mounting bracket angular.
WALL MOUNTING
1
3
2
5
4 6
1. Insert the shielded cable alarm in the fixing plate;
2. Fix the plate at wall ;
3. Drill hole in the rubber nut and slide inside the cable;
4. Screw the base on the plate;
5. Fix the NAT motherboard on the support base and connect wires;
6. After the wiring and operation test close NAT sure that the seals and the O-rings are present and
not damaged to ensure the integrity of the product.
Politec S.r.l. | Man NAT– Ver. 1.5 4
WALL MOUNT WITH “L” BRACKET
4 2
6
3
1. Insert the shielded alarm cable into the slots of the bracket angle and fasten it to the wall;
2. pass the cable through the mounting plate;
3. fix the plate to the fastening bracket angle;
4. Drill hole in the rubber nut and slide inside the cable;
5. Screw the base on the plate;
6. Fix the NAT motherboard on the support base and connect wires;
7. After the wiring and operation test close (7) NAT sure that the seals and the O-rings are present and
not damaged to ensure the integrity of the product.
Politec S.r.l. | Man NAT– Ver. 1.5 5
3. COVERAGE AREA
SIDE VIEW
VIEW FROM ABOVE
NB: The system can also detect the areas underlying the sensor Nat adjusting the range (sensitivity) of
the two technologies (see below).
Politec S.r.l. | Man NAT– Ver. 1.5 6
4. PROGRAMMIN AND OPERATION
Install the sensor Nat between 2 and 3 meters in height from the floor concerned following the
instructions on page 4. Connect the power supply according to polarity (10-30V) and connect the
outputs Alarm, Tamper and Anti-Mask in central according to their usage requirements.
1 Power supply of NAT
1 5 2 +/GND 10/30Vdc.
2 6 ANTI- Open collector negative.Opens
3
3 7 MASK in the event of masking.
4 8 STAND- Positive input. the system is
4 inhibited if an + is connected.
BY
5 N.C. Tamper output. It opens
TMP in case of sensor tampering.
6
7 N.C. Alarm output. It opens in
ALARM case of detection MW+IR.
8
POWER LED ON FOR DETECTION TEST
Turn on the dipswitch number 4 for the
functionality of the LEDs detection.
MW RANGE
(SENSITIVITY) 1-12m 1 2 3 4
REGULATION ON
TRIMMER: Adjust the
microwave range through
the trimmer, implementing Power on for the duration of about 30 seconds if
with crossing test. the DIP4 of the LEDs is activated you will see an
Submitting GREEN LED alternate flashing of these,for the stabilization
will help to verify the of the system. Term of flashes you can proceed
detection of the passage in with the following settings.
different areas (exp. 0m, 4m,
7m, 12m). Test the goodness
of the coverage of the
affected areas, by adjusting
the PIR.
PIR RANGE (SENSITIVITY) 1-12m
REGULATION TRIMMER: Adjust the
PIR range through the trimmer,
implementing with crossing test. Submitting
ORANGE LED will help to verify the
detection of the passage in different areas
(exp. 0m, 4m, 7m, 12m). Test the goodness
of the coverage of the affected areas, by
adjusting the MW.
Politec S.r.l. | Man NAT– Ver. 1.5 7
5. ADDITIONAL FEATURES
FILTER DISTURBS
Turn the DIP switch number 1 to filter and reduce noise at 100Hz. caused by external agents such as
NEON lights.
N.B.: Use this feature (reduced sensitivity) ONLY in the presence of such a source of disturbance in the
extreme vicinity.
Carry out a repetition of the MW range adjustment and test the goodness of the coverage of the affected
areas by adjusting the PIR.
1 2 3 4
ON
ANTI-MASK
Turn the dipswitch number 2 for the functionality ANTI-MASK. Activating this function when an object is
placed in front of the sensor to blind it and make it ineffective, an active infrared system checks for the
presence of these in 3 seconds and gives an output signal through dedicated. The anti-mask microwave
verification of the presence of an object check in 20 seconds the presence of an object and gives an output
dedicated.
N.B.: If DIP 2 (anti-mask) and 4 (LED) are activated when it comes in a stealth mode, led blinking green-
orange alert the opening of the contact ANTI-MASK.
WARNING: When activated the DIP 2 before leaving the installation spot, you MUST close the sensor
NAT and you MUST power down and power up the entire system.
1 2 3 4
ON
SECURITY FUNCTION
Turn the dipswitch number 3 functionality SECURITY. Activating this function if the MW sensor
provides at least 7 distinct surveys in 30 seconds, the alarm signal from a system independently of the PIR
sensor readings. Dually the IR sensor provides at least 4 separate surveys in 30 seconds, the system by an
alarm signal regardless of the sensor readings MW.
1 2 3 4
ON
When the test and programming are ended turn off the LED settings provide to secure the cover.
Politec S.r.l. | Man NAT– Ver. 1.5 8
6. DESCRIPTION OF NOT SETTABLE FUNCTION
PET IMMUNITY SYSTEM
The system of pet immunity is able to discriminate the small animals up to a maximum of 10kg and not to
give an alarm signal. In the case of animals such as dogs and cats perform function tests.
SELF-DIAGNOSIS SYSTEM
The system will periodically check every 50sec about the functionality of the microwave and PIR system.
In case of Malfunction of one of the two detection equipment, this is signaled by the flashing of the LED
dedicated (GREEN and ORANGE for MW for IR), steadily. In this condition the system excludes the
operation of the technology is not working and the detection will continue to be present in the OR mode.
AUTO-THERMAL SYSTEM
The system detects the temperature of the surrounding environment through a dedicated sensor and modify
the detection parameters of the IR sensor in order to adapt to extreme environmental conditions.
AUTO-ENVIRONMENTAL SYSTEM
The system locates in the case of heavy rains and snowfall an environmental condition "different" after
about 20 seconds and is able to adapt the system to the detection threshold by changing the parameters of
both technologies for the duration of the event.
Politec S.r.l. | Man NAT– Ver. 1.5 9
7. APPLICATION
Example 1: "wall covering"
The sensor can be commonly used for the protection of facades using the bracket to "L", and thanks to the
new system of AUTO-ENVIRONMENTAL is able to reduce to zero the possibility of "false alarms". The
installation MUST be carried out at height between 2 and 3m by adjusting the range and sensitivity of the
two technologies (MW + IR).
Example 2: “Curtain for windows or doors”
Politec S.r.l. | Man NAT– Ver. 1.5 10
8. TECNICAL SPECIFICATION
Description Value
Max range detection IR Adjustable 1-12m
Max range detection MW Adjustable 1-12m
MW Frequency / 24.125Ghz
80° vertical –
Angle IR coverage /
6° horizontal
80° vertical –
Angle MW coverage /
30° horizontal
Power supply / 10 – 30 Vdc
Absorption on alarm / 42mA
Absorption standby / 40mA
Alarm Output N.C. /
Tamper Output N.C. /
Max range detection IR Open collector - /
Stand-by input INPUT + /
Operating Temperature -20°+65° C
Dimensions 135mm X 33mm X 40mm
Weight 150gr
Mounting brackets
TOTAL WARRANTY 2 YEARS
Politec S.r.l. | Man NAT– Ver. 1.5 11
Politec S.r.l. | Man NAT– Ver. 1.5 12
