STRUCTURAL NOTES :-

NOTE-;FIXING DETAIL C/W APPROVEDMECHANICAL VENDER DRAWING

1. ALL DIMENSIONS ARE GIVEN IN MM.
2. ALL WRITTEN DIMENSIONS SHOULD BE FOLLOWED.
60mm thick p.c.c. of 3. DRAWINGS SHOULD BE CHECKED AND VERIFIED AS PER SITE
3-20Ø MM GI PIPE
1500 M-10 grade 40mm thick c.c. ANCHOR FASTENERS TANK WALL CONDITION BEFORE EXECUTION OF THE WORK BY THE EXECUTIVE
flooring with M-15 ENGINEER CONCERNED.
aggregate
grade
1000 4. ANY DISCREPANCY OR DOUBTS ARISING FROM THE STUDY OF ALL
RELEVANT DRAWING SHALL BE BROUGHT TO THE NOTICE OF THE
F.G.L 915 85 ENGINEER IN CHARGE FOR CLARIFICATION BEFORE COMMENCEMENT

1000
OF CONCRETING.
M S ANGLE IRON POST WALKWAY SLAB 5. THE CONTRACTOR SHALL FULLY SATISFY AND OBTAIN PRIOR

℄
(50 X 50 X 6) APPROVAL OF THE ENGINEER IN CHARGE REGARDING ALL ASPECTS
@ 1500 C/C 2- Brick edge protection OF THE SPECIFICATION WORK MAIN SHIP AND ISI STANDARD BEFORE
Well compacted 100mm COMMENCEMENT AND PLACEMENT OF ALL.
6. THE CONTRACTOR SHOULD NOT BE PERMITTED TO INSTALL
subgrade with coarse CONDUITS PIPES ,DUCTS, SLEEVES OR ANY CUTTING WORK THAT
EL +12000mm sand ARE NOT SHOWN ON THE PLANS OR NOT APPROVED BY THE
ENGINEER OR ARCHITECT.
WALKWAY Plinth Protection (section 3-3) 7- GRADE OF CONCRETE SHALL BE M25 WITH MINIMUM CEMENT ON
LIGHTNING ARRESTER MAIN RING BEAM 715 300Kg/m CUB WITH NOMINAL AGGREGATE SIZE OF 20mm.
8-ALL REINFORCEMENT BARS SHALL BE HYSD BARS OF GRADE Fe500
BEAM (RB1) CONFORMING TO IS:1786.
9-CLEAR COVER TO MAIN REINFORCEMENT SHALL BE :
TANK DIA=5690 a) COLUMN =40mm
b) BEAMS=30mm
c) SLABS=30mm
COLUMN d) PILE =50mm, PILECAP 75MM
e) STAIRCASE=30mm
MAN HOLE RAILING MAN HOLE 10- ALL LAPS SHALL BE 49 TIMES DIA OF BAR FOR M25 GARDE OF
CONCRETE .
11- PIPE DETAILS SHOWN ARE TENTATIVE. PIPE DETAILS REFER
DETAIL OF M S POSTS AND PIPES FOR RAILING COLUMN MECHANICAL G.A DRAWINGS
12- NET PILE CAPACITY CONSIDERED SHALL BE 360KN OF 500MM DIA PILE.
+ 4950 + 3300 13- OVER EXCAVATION SHALL BE FILLED WITH PCC 100mm
100MM EXTRA PCC SHOULD BE PROVIDED AT PILE CAP

M.W.L
LVL. LVL. LIGHTNING ARRESTER &WATER INDICATOR:-
447 10X300=3000 447 SPOT DETAIL -D
EXTERNAL LADDER 5 96 Lightening Arrestor:-Shall be of copper bars 25 mm dia and 1000 mm long to be
96 5
10 60 10 provided at the top periphery of OHT. This is to be connected by aluminium Strip of 25
WITH CAGE OVER FLOW PIPE mm wide and 3 mm thick.This conductor strip shall be connected to a 450x450x3mm
INLET PIPE
80X80X8 THK. thick copper plate to be embedded below the average ground level by digging a pit.

1000
7

44
B1
INSERT

44
30°

B1
Water level indicator:- Providing and fixing water level indicator consisting of an

7
30°

20
SS
approved G.I. float and iron counter weight connected by steel flexible wire rope
PLATE(M.S)

SS
passing over frictionless aluminum pulleys will be fixed as provided in elevation. The
4250

scale shall be calibrated in centimeters and should consist of iron sheet 8 gauge fixed
over wooden planks with in angle iron frame of 35x35x5 mm and painted with white
2 2

10
0
enamel base and letters in black and red fluorescent paint

00
INTERNAL LADDER

X3

20 40
1

=3

00
00
00

=3
OUTLET PIPE 10

X3
DRAIN PIPE

00
10
10 2NO.8Ø LUG

0
00

2537
200
EL +12000mm DETAIL OF HAND RAIL INSERT PLATE
(T.O.C.)

44
44

7
90
°

°
600

90
715 + 6600 600 1000

5074
+ 1650 80X80X8 THK.

965

965
SSB1
SPOT DETAIL -A 2 LVL. SSB1 LVL. INSERT PLATE
RB1 6
GB1/GB2

40 8
44

7
52
2537

7
SPOT DETAIL -D 3300
40 8Ø LUG

10

00
SECTION 2-2

X
0

30
00

30
1

0=
0=
3

30
30

30°
EL +8700mm

X
00

10
SS 0.5
B1
(T.O.C.) +0
0L M S ANGLE FRAME

SS
30° VL 35 X 35 X 4 MM 1.0
.

B1
TB3 TB3 TB3

44
7
LEVEL INDICATOR FLEXIBLE STEEL
96
5 TWISTED FLOAT WIRE 1.5

+ 8250 447
3300

2.0
LVL. BRACING AT

SPOT DETAIL -C
1465 2930 1465 EVERY
900 MM APART BE
5860 WELDED 2.5

EL +5400mm 6Ø MM RING WELDED 3.0

A B C D FOR FLOAT WIRE
(T.O.C.)
STAIR PLAN 3.5
Ø6 MM RING FOR GUIDE WIRE
TB2 TB2 TB2
3300

8 GAUGE GUIDE WIRE

1

+ 12000
2537

EL +2100mm LVL.

60
MS SHEET PAINTED WITH
(T.O.C.) 1

0
B ENAMEL PAINT
SS SPOT DETAIL -C

62
90

2
°
TB1 TB1 TB1
600 1000
5074

+ 11550

1113
PLINTH PROTECTION ALL
2575

AROUND
2 SSB1 LVL. LIGHTNING ARRESTER UNIVERSAL MEP PROJECTS & ENGINEERING
SERVICES LTD - A TATA ENTERPRISE
EGL +00mm
3 CLIENT :
STATE WATER AND SANITATION MISSION (SWSM), UTTAR

7
TANK

44
PRADESH NAMAMI GANGE AND RURAL WATER SUPPLY
2537

DEPARTMENT GOVERNMENT OF UTTAR PRADESH

PROJECT :IMPLEMENTATION OF VARIOUS RURAL WATER
3 SUPPLY PROJECTS IN THE STATE OF UTTAR PRADESH UNDER

0
EL -475mm
1575

THE JAL JEEVAN MISSION.

00
THIS DRAWING IS UNDER COPYRIGHT OF
(T.O.C.) =3 CONSULTING & RESEARCH PRIVATE LIMITED
00
3 & NOT TO BE REPRODUCED OR COPIED HANDED
X3

GRADE BEAM
OUTLET PIPE OVER TO THIRD PARTY OR USES FOR ANY PURPOSE
10

THAN THAT FOR IT HAS BEEN LOANED

WALKWAY SLAB
B1
SS

30° 30°
SS
B1

7
44

44
7

96 PUDDLE COLLER
5 5
96 + 9900
+ 8250 447 10X300=3000 447 TITLE-: NUMERATION & RC DETAILING OF 100KL
LVL. RB1 12M STAGING KONHAWALIA BABURAI-TARKULWA-DEORIA
LVL. C1 JOB NO.- DWG. REF. NO.- SHEET SIZE
1465 2930 1465 A2
SCALE- REVISION-
1465 2930 1465 5860 GENERAL DETAIL-A FOR PIPE
NTS R0
DATE OF ISSUE-
05-02-24
5860 PLACEMENT DWG.NO.-
43/JJM/DWP/TATA/100/12/2024
1 2 3 4 A B C D N
DESIGN BY- JN SHEET NO- 1/3
STAIR PLAN
FOUNDATION PLAN DRAWN BY- MS CHECKED BY- SK
 Balcony Level BEAM STRUCTURAL NOTES :-
SECTION AT SUPPORT SECTION AT MIDSPAN T.O.C. OF BEAM STIRRUPS 1. ALL DIMENSIONS ARE GIVEN IN MM.
MARKED 2. ALL WRITTEN DIMENSIONS SHOULD BE FOLLOWED.
PILE CAP 3. DRAWINGS SHOULD BE CHECKED AND VERIFIED AS PER SITE

700
TOP LEVEL

>H/4
CONDITION BEFORE EXECUTION OF THE WORK BY THE EXECUTIVE
PILE CAP
COLUMN #10Ø@150C/C COLUMN
PILE CAP 450 450
ENGINEER CONCERNED.
4-#16Ø
#10Ø@100C/C 4-No. #16Ø 4-No. #16Ø 4. ANY DISCREPANCY OR DOUBTS ARISING FROM THE STUDY OF ALL
RELEVANT DRAWING SHALL BE BROUGHT TO THE NOTICE OF THE

H
. .
GRADE 4-No. #10Ø 4-No. #10Ø EL(-475MM) ENGINEER IN CHARGE FOR CLARIFICATION BEFORE COMMENCEMENT
#8Ø@150C/C
. . .

600

600
OF CONCRETING.
BEAM

1100

1100
#10Ø100C/C #10Ø150C/C
. . . . . . . . . . . . . .

5. THE CONTRACTOR SHALL FULLY SATISFY AND OBTAIN PRIOR

. .

APPROVAL OF THE ENGINEER IN CHARGE REGARDING ALL ASPECTS

1100
OF THE SPECIFICATION WORK MAIN SHIP AND ISI STANDARD BEFORE

800
PILE CUT-OFF Lvl.

>H/4
770 770 #10Ø100/150C/C

700
#8Ø@100C/C 4-No. #16Ø COMMENCEMENT AND PLACEMENT OF ALL.

CONFINEMENT
-1500 4-#16Ø TB3 4-No. #16Ø 6. THE CONTRACTOR SHOULD NOT BE PERMITTED TO INSTALL
CONDUITS PIPES ,DUCTS, SLEEVES OR ANY CUTTING WORK THAT

ZONE
2-10Ø ON EITHER 400 400 ARE NOT SHOWN ON THE PLANS OR NOT APPROVED BY THE
100 THK. LEVELING 100 THK. LEVELING ENGINEER OR ARCHITECT.

700
FACE 4-No. #12Ø 4-No. #12Ø 7- GRADE OF CONCRETE SHALL BE M25 WITH MINIMUM CEMENT ON
COURSE COURSE 300Kg/m CUB WITH NOMINAL AGGREGATE SIZE OF 20mm.
EL(+12000MM)
75
4-No. #10Ø 4-No. #10Ø 8-ALL REINFORCEMENT BARS SHALL BE HYSD BARS OF GRADE Fe500

600

600
RB1 CONFORMING TO IS:1786.
100 THK. LEVELING #8Ø100C/C #8Ø150C/C 9-CLEAR COVER TO MAIN REINFORCEMENT SHALL BE :
a) COLUMN =40mm
COURSE b) BEAMS=30mm

>H/4
#8Ø@100C/C
LONGITUDINAL SECTION OF GRADE BEAM

700
#8Ø100/150C/C c) SLABS=30mm

CONFINEMENT
TB2
4-No. #12Ø 4-No. #12Ø d) PILE =50mm, PILECAP 75MM
e) STAIRCASE=30mm

ZONE
COLUMN 10- ALL LAPS SHALL BE 49 TIMES DIA OF BAR FOR M25 GARDE OF
5000

400 400 CONCRETE .

6-No. #16Ø

700
>H/4
4-No. #16Ø 11- PIPE DETAILS SHOWN ARE TENTATIVE. PIPE DETAILS REFER
8Ø@100C/C MECHANICAL G.A DRAWINGS
12- NET PILE CAPACITY CONSIDERED SHALL BE 360KN OF 500MM DIA PILE.
COLUMN 4-No. #10Ø 4-No. #10Ø EL(+12000MM) 13- OVER EXCAVATION SHALL BE FILLED WITH PCC 100mm

600

600
GRID BEAM 100MM EXTRA PCC SHOULD BE PROVIDED AT PILE CAP
LAP LENGTH #10Ø100C/C #10Ø150C/C
LEGENDS:

700
700
#10Ø100/150C/C
#8Ø@150C/C SCHEMATIC LAP 4-No. #16Ø 4-No. #16Ø FGL- FINISHED GROUND LEVEL
2-#16Ø EGL- EXISTING GROUND LEVEL

LAP ZONE
2-#16Ø 2-#16Ø
735 735 BOC- BOTTOM OF CONCRETE
A A 200
2-No. #16Ø
200
2-No. #16Ø
TOC- TOP OF CONCRETE
GB-GRID BEAM
EL- ELEVATION
#8Ø@150C/C SSB- STAIRCASE SUPPORTING BEAM
. . . . . .

2-No. #16Ø PB- PLINTH BEAM

EL(+2100MM)

>H/4
#8Ø@100C/C TB1,TB2

600

600
2-No. #10Ø 2-No. #10Ø

700
. . . . . . . . . . . .

EL(+5400MM) TB- TIE BEAM

TB3 RB- RING BEAM

CONFINEMENT
TB1 #8Ø100C/C EL(+8700MM)
#8Ø150C/C BOF-BOTTOM OF FOOTING
2-No. #16Ø TOL-TOP OF LANDING

ZONE
#8Ø@100C/C 1-10Ø ON 2-No. #16Ø 2-No. #16Ø #8Ø100C/C COC- CENTER OF CONCRETE
8Ø@150C/C 2-#16Ø 2-#16Ø EITHER FACE
2-#16Ø #8Ø150C/C

700
>H/4
230 230 EL(+00MM)
3-No. #16Ø 3-No. #16Ø EL(+1650MM)
(7+8+7)-#8ØSTIRRUPS EL(+3300MM)

400
COLUMN

400
8Ø@150C/C 8Ø@150C/C EL(+4950MM)
SSB1 EL(+6600MM)
10 No.-16Ø LONGITUDINAL SECTION OF TIE BEAM (TB) 3-No. #12Ø 3-No. #12Ø EL(+8250MM)
15000

H
#8Ø@150C/C EL(+9900MM)
EL(+11550MM) #8Ø150C/C
EL(+12000MM)

SCHEDULE OF COLUMN
FGL
0 0
15 15
825 COLUMN MARKED C1
500

>H/4
TOP LEVEL PILE CAP
TOP OF COLUMN EL+12M FROM E.G.L.

700
#8Ø@100C/C
BEAM SSB1 VERTICAL REINF. 7No. #16Ø
10000

8Ø @ 150 MM C/C
TIES #8Ø@100/150c/c
LATERALLY
10 No.-16Ø 300 PILE CUT-OFF Lvl. -1500
7-12Ø
8Ø@100/150C/C CROSS SECTION

400
OF COLUMN

#16Ø @ 1500C/C 150 #8Ø@100/150c/c

150 mm thick
STIFFNER BARS COLUMN SIZE 400Dia.
825 7-12Ø 100 THK. LEVELING COLUMN STARTING
COLUMN TOP OF THE FOOTING

PILE COURSE LEVEL

7-12Ø

8Ø @ 150 MM C/C LATERALLY

0 0 #10Ø@150 links outside confinement zone for C1 column
15 15
#10Ø@100 links in lap zone 75MM THICK R.C.C
Provide lapping of main reinforcement in lap zone
BEAM SSB1
and staggered lapping of alternate bars as shown PRECAST SLAB

300
900
REINFORCEMENT DETAIL OF 1 TO 4 FLIGHTS OF STAIR CASE E.G.L
230 230

12mm inner plaster

SECTION OF PILE SLUICE
VALVE

900
COLUMN
°

60
60

A
°

20Ø@140C/C MAIN CORE

PIPE
CORE
PIPE

16Ø@150C/C DIST.

125MM M15
2537

GRADE BEAM 12Ø@150C/C P.C.C.

10Ø-4L@150C/C LACER BAR GENERAL SECTION(2-2) OF VALVE
1100

CHAMBER
5074

3No.#8Ø #8Ø@250C/C

200

.
.

.
16Ø@150C/C DIST. 100mm P.C.C 1360 UNIVERSAL MEP PROJECTS & ENGINEERING
20Ø@140C/C MAIN R.C. DETAIL OF PRECAST SLAB SERVICES LTD - A TATA ENTERPRISE
(TOP VIEW) CLIENT :
STATE WATER AND SANITATION MISSION (SWSM), UTTAR
PILE
2537

PRADESH NAMAMI GANGE AND RURAL WATER SUPPLY

230 900 230 DEPARTMENT GOVERNMENT OF UTTAR PRADESH
PROJECT :IMPLEMENTATION OF VARIOUS RURAL WATER

230
125 SUPPLY PROJECTS IN THE STATE OF UTTAR PRADESH UNDER
SECTION A-A' THE JAL JEEVAN MISSION.
THIS DRAWING IS UNDER COPYRIGHT OF
CONSULTING & RESEARCH PRIVATE LIMITED
& NOT TO BE REPRODUCED OR COPIED HANDED
2300 (PILE CAP) OVER TO THIRD PARTY OR USES FOR ANY PURPOSE
C THAN THAT FOR IT HAS BEEN LOANED
°
60

60
°

2
400 400

1200
A 2
A'
800
.
.

500 Ø PILE
TITLE-: NUMERATION & RC DETAILING OF 100KL
PILE CAP 12M STAGING KONHAWALIA BABURAI-TARKULWA-DEORIA
5860 JOB NO.- DWG. REF. NO.- SHEET SIZE
1465 2930 1465 100 MM THK. PCC A2
400 1500 C/C PILE 400 SCALE- REVISION- DATE OF ISSUE-

230
NTS R0 05-02-24
1 2 3 4 DWG.NO.-
43/JJM/DWP/TATA/100/12/2024
2 PILE GROUP PILE CAP TOP VIEW OF VALVE CHAMBER
N DESIGN BY-
JN
SHEET NO-
2/3
FOUNDATION PLAN WITH GRADE BEAM DRAWN BY- CHECKED BY-
MS SK
 STRUCTURAL NOTES :-
#10Ø@150C/C(circumferential) #10Ø@150C/C(circumferential) #10Ø@150C/C(circumferential)
1. ALL DIMENSIONS ARE GIVEN IN MM.
#10/10Ø@280C/C #10/10Ø@280C/C #10/10Ø@280C/C #10/10Ø@280C/C 2. ALL WRITTEN DIMENSIONS SHOULD BE FOLLOWED.
3. DRAWINGS SHOULD BE CHECKED AND VERIFIED AS PER SITE
#10Ø@150C/C(circumferential) #10/10Ø@280C/C #10/10Ø@280C/C CONDITION BEFORE EXECUTION OF THE WORK BY THE EXECUTIVE
1300 1300 ENGINEER CONCERNED.
#10/10Ø@280C/C #10/10Ø@280C/C
700 700 4. ANY DISCREPANCY OR DOUBTS ARISING FROM THE STUDY OF ALL
RELEVANT DRAWING SHALL BE BROUGHT TO THE NOTICE OF THE
ENGINEER IN CHARGE FOR CLARIFICATION BEFORE COMMENCEMENT
OF CONCRETING.
5. THE CONTRACTOR SHALL FULLY SATISFY AND OBTAIN PRIOR
APPROVAL OF THE ENGINEER IN CHARGE REGARDING ALL ASPECTS

150

150
OF THE SPECIFICATION WORK MAIN SHIP AND ISI STANDARD BEFORE
COMMENCEMENT AND PLACEMENT OF ALL.
6. THE CONTRACTOR SHOULD NOT BE PERMITTED TO INSTALL
715 600

600

600

600

600
715 CONDUITS PIPES ,DUCTS, SLEEVES OR ANY CUTTING WORK THAT
600 #10/10Ø@280C/C ARE NOT SHOWN ON THE PLANS OR NOT APPROVED BY THE
#10/10Ø@280C/C ENGINEER OR ARCHITECT.

200

200
7- GRADE OF CONCRETE SHALL BE M25 WITH MINIMUM CEMENT ON
RING BEAM GRID BEAM GRID BEAM 300Kg/m CUB WITH NOMINAL AGGREGATE SIZE OF 20mm.
8-ALL REINFORCEMENT BARS SHALL BE HYSD BARS OF GRADE Fe500
(400X600) (400X550) (400X550) RING BEAM CONFORMING TO IS:1786.
9-CLEAR COVER TO MAIN REINFORCEMENT SHALL BE :
(400X600) a) COLUMN =40mm
b) BEAMS=30mm
SECTION 1-1 c) SLABS=30mm
d) PILE =50mm, PILECAP 75MM
e) STAIRCASE=30mm
400 400 400 400 10- ALL LAPS SHALL BE 49 TIMES DIA OF BAR FOR M25 GARDE OF
CONCRETE .
COLUMN 11- PIPE DETAILS SHOWN ARE TENTATIVE. PIPE DETAILS REFER
COLUMN MECHANICAL G.A DRAWINGS
12- NET PILE CAPACITY CONSIDERED SHALL BE 360KN OF 500MM DIA PILE.
13- OVER EXCAVATION SHALL BE FILLED WITH PCC 100mm
100MM EXTRA PCC SHOULD BE PROVIDED AT PILE CAP
LEGENDS:
FGL- FINISHED GROUND LEVEL
EGL- EXISTING GROUND LEVEL
BOC- BOTTOM OF CONCRETE

3No. of 10Øcircumferential bar at 150c/c WALKWAY SLAB WALKWAY SLAB

TOC- TOP OF CONCRETE
GB-GRID BEAM
EL- ELEVATION
SSB- STAIRCASE SUPPORTING BEAM
PB- PLINTH BEAM
TB- TIE BEAM
tial) RB- RING BEAM
( c ir c u mferen BOF-BOTTOM OF FOOTING
150C/C TOL-TOP OF LANDING
#10Ø@ COC- CENTER OF CONCRETE

5
71
#10Ø@280C/C at beam outer face

600
#10Ø@280C/C at beam outer face
5
71

70
#10Ø@150C/C(circumferential)

0
13
2000

600

00

1450
00
13
3343

3343

60
60
#10Ø@280C/C
.

0
GB1

0
GB1 1 1
#10Ø@280C/C B

62
SB

62
800 2530 800 S SS

2
3790

1
888 888

2
3805

1 GB2 1 200THK.

1113
1113
SSB1 SSB1

5523
500
#10Ø@280C/C 500
200THK. #10Ø@280C/C
#10Ø@280C/C #10Ø@280C/C

7
600 600

44
44
888 888

3790

600
600 #10Ø@280C/C

1450
2000

#10Ø@280C/C

0
3316

3343

00

00
0
10

=3
10

=3
00 00

00
600

00

X3
X3

10
10

600
R.C. DETAIL OF SLAB AT (+) 12.0M LEVEL
R.C. DETAIL OF SLAB AT (+) 12.0M LEVEL (TOP MESH)
(BOTTOM MESH)

GRID BEAM(GB1) GRID BEAM(GB1) 2-#16Ø

2-#16Ø #10Ø@150C/C 2-10Ø ON EITHER
4-#16Ø
RING BEAM 1065 FACE 1065 RING BEAM
Ld Ld
. . . . . . . . . .. .. .. .. . . .. .. .

. . . . . . . . . . . . . . . . . . . .

UNIVERSAL MEP PROJECTS & ENGINEERING

#10Ø@150C/C #10Ø@150C/C
700

4-#16Ø SERVICES LTD - A TATA ENTERPRISE

#10Ø@100C/C #10Ø@100C/C
CLIENT :
STATE WATER AND SANITATION MISSION (SWSM), UTTAR
(11+17+11)-#10ØSTIRRUPS PRADESH NAMAMI GANGE AND RURAL WATER SUPPLY
DEPARTMENT GOVERNMENT OF UTTAR PRADESH
COLUMN LONGITUDINAL SECTION OF GRID BEAM (GB2)
PROJECT :IMPLEMENTATION OF VARIOUS RURAL WATER
SUPPLY PROJECTS IN THE STATE OF UTTAR PRADESH UNDER
THE JAL JEEVAN MISSION.
THIS DRAWING IS UNDER COPYRIGHT OF
CONSULTING & RESEARCH PRIVATE LIMITED
& NOT TO BE REPRODUCED OR COPIED HANDED
OVER TO THIRD PARTY OR USES FOR ANY PURPOSE
THAN THAT FOR IT HAS BEEN LOANED
770 4-#12Ø 770 2-10Ø ON EITHER GRID BEAM(GB2) 2-#16Ø RING BEAM
2-#16Ø FACE 4-#16Ø
4-#16Ø
RING BEAM 1300 1300
. . . . . .. .. . . . . . . . . . . . . . . .

Ld Ld
. . . . . . . .

. . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . .

#8Ø@100C/C 2-10Ø ON EITHER TITLE-: NUMERATION & RC DETAILING OF 100KL

700

4-#12Ø #8Ø@150C/C
FACE 12M STAGING KONHAWALIA BABURAI-TARKULWA-DEORIA
700

#10Ø@150C/C 4-#16Ø #10Ø@150C/C JOB NO.- DWG. REF. NO.- SHEET SIZE
#10Ø@100C/C #10Ø@100C/C A2
(8+8+8)-#8ØSTIRRUPS SCALE- REVISION- DATE OF ISSUE-
NTS R0 05-02-24
COLUMN DWG.NO.- 43/JJM/DWP/TATA/100/12/2024
COLUMN COLUMN
(13+7+7+13)-#10ØSTIRRUPS N DESIGN BY- SHEET NO-
JN 3/3
LONGITUDINAL SECTION OF RING BEAM (RB1) DRAWN BY- CHECKED BY-
LONGITUDINAL SECTION OF GRID BEAM (GB1) MS SK