SERVICE MANUAL

AG-D9260
AV Digital Home Theater Receiver

NOTES

● PC boards shown are viewed from parts side.

● The parts with no reference number or no parts number in the
exploded views are not supplied.
● As regards the resistors and capacitors, refer to the circuit diagrams

contained in this manual.

● £ Parts marked with this sign are safety critical components. They

must be replaced with identical components - refer to the appropriate

parts list and ensure exact replacement.
● Parts of [ ] mark can be used only with the version designated.

[US]:U.S.A. [C]:CANADA [E]:EUROPE [UK]:U.K.

Effective : January, 2002 S-0000A

 CONTENTS

SPECIFICATIONS.................................................................................................................................3

SAFETY INSTRUCTIONS ...................................................................................................................4

MEASUREMENTS AND ADJUSTMENTS ........................................................................................5

FIP DISPLAY ........................................................................................................................................8

DISPLAY PIN CONNECTION ..............................................................................................................9

IC BLOCK DIAGRAMS AND PIN FUNCTIONS ................................................................................10

EXPLODED VIEWS AND PARTS LIST .............................................................................................22

PC BOARDS AND PARTS LIST ........................................................................................................ 24

INCLUDED ACCESSORIES ...............................................................................................................29

2
 SPECIFICATIONS

Amplifier Section AM Tuner Section

Surround Output Power (0.9 % THD, 1 kHz, 8 ohms): Tuning Range:
100 + 100 watts (Front) 522 kHz – 1,620 kHz (10 kHz steps)
100 watts (Center) 539 kHz – 1,720 kHz (10 kHz steps: [us/c] )
100 + 100 watts (Rear) Usable Sensitivity: 55 dB/m
Delay Time: Total Harmonic Distortion: 0.8% at 85 dB/m
DOLBY DIGITAL: REAR 0 – 15 ms Signal-to-Noise Ratio: 45 dB at 85 dB/m
CENTER 0 – 5 ms
DOLBY PRO LOGIC: REAR 15 – 30 ms Video Section
Audio Input Sensitivity/Impedance: Input Sensitivity/Impedance: 1.0 Vp-p/75 ohms
*LINE: 220 mV/47 k ohms Output Level/Impedance: 1.0 Vp-p/75 ohms
Output Level/Impedance:
CD-R/TAPE REC: 200 mV/2.2 k ohms General
Frequency Response: Power Requirements:
*LINE: 20 Hz – 65 kHz, +1/ –3 dB [E/UK] : 230V AC, 50Hz
Signal-to-Noise Ratio: [US/C] : 120V AC, 60Hz
*LINE: 95dB (IHF-A)
Tone Control: Power Consumption:
BASS: ± 10 dB at 100 Hz [E/UK] : 300W
TREBLE: ± 10 dB at 10 kHz [US/C] : 2.8A
Digital Audio Section AC Outlets:
Sampling Frequency: 32 kHz, 44.1 kHz, 48 kHz, 96 kHz Switched x 2, Total 100 W max. (1 A max.)
DIGITAL Input Level/Impedance: (U.S.A./Canada model)
DIGITAL 1, 2 (OPTICAL): –15 dBm — –21 dBm Dimensions (W x H x D)
DIGITAL 3 (COAXIAL): 0.5 Vp-p / 75 ohms 435 x 165 x 350 mm (17-1/8" x 6-1/2" x 13-3/4")
Weight (net):
FM Tuner Section [E/UK] : 9.5kg
(Without notes 100.1 MHz, 65 dBf) [US/C] : 9.4kg(20-11/16lb)
Tuning Range:
87.5 MHz – 108.0 MHz (50 kHz steps, [us/c]:100kHz steps) Standard Accessories:
Usable Sensitivity (IHF): AM Loop Antenna x 1
Mono: 11.2 dBf FM T-type Antenna x 1[E/uk]
50 dB Quieting Sensitivity: FM T-type Antenna x 1
Mono: 15.3 dBf Remote Control Unit (UR-417) x 1
Stereo: 38.5 dBf
Capture Ratio: 2.0 dB
Image Rejection Ratio: 80 dB ( [us/c]: 45dB ) * LINE means CD, CD-R/TAPE, VCR/VIDEO 1, DBS/VIDEO 2,
AM Suppression Ratio: 55 dB DVD/VIDEO 3 and AUX/VIDEO 4.
Total Harmonic Distortion (1 kHz):
Mono: 0.4% < Improvements may result in specifications and features
Stereo: 0.5% changing without notice.
Frequency Response: 30 Hz – 15 kHz, +1/ –1.5 dB < Illustrations may differ slightly from production models.
Stereo Separation (1 kHz): 40 dB
Signal-to-Noise Ratio:
Mono: 75 dB
Stereo: 70 dB

3
SAFETY INSTRUCTIONS
PRECAUTIONS DURING SERVICING The leakage-current should be less than 0.5mA rms AC.
1. Parts identifide by the ( )symbol parts are critical The resistance measurement should be done between
for safety. Replace only with parts number specified. accessible exposed metal parts and power cord plug
2. In addition to safety, other parts and assemblies are prongs with the power switch (if included) "ON". The
specified for conformance with such regulations as resistance should be more than 2.2M Ohms.
those applying to spurious radiation. PRECAUTIONS IN REPAIRING
These must also be replaced only with specifide When repairing or adjusting the unit, please note the
replacements. following points.
Examples :RF converters, tuner units, antenna 1. Do not put excessive pressure on the mechanical
selectswitches, RF cables, noise blocking capacitors, part (operation part), including the pick-up block, as
noise blocking filters, etc. extremely high mechanical precision is required in
3. Use specified internal wiring. Note especially : these parts.
1) Wires covered with PVC tubing 2. When the base is removed for repair adjustment,
2) Double insulated wires make sure that there are no metal obiects in the
3) High voltage leads narrow gap between the P. C. board or the mecha
4. Use specified insulating materials for hazardous live parts and the base
parts. Note especially: 3. The Micro-Computer and the CD signal processing
1) Insulation Tape ICs can be damaged by static electricity or leakage
2) PVC tubing from a soldering iron during repairing. While
3) Spacers(insulating barriers) soldering, please take the precautions against
4) Insulation sheets for transistors leakage as in the illustration.
5) Plastic screws for fixing micro switches
5. When replacing AC primary side components
(transformers, power cords, noise blocking
capacitors, etc.), wrap ends of wires securely about
the terminals before soldering.

GND
6. Make sure that wires to do not contact heat 4. Do not loosen any screws in the pick-up block.
producing parts (heat sinks, oxide metal film When handing the pick-up block, please refer to the
resistors, fusible resistors, etc.). points to NOTE when replacing the pick-up block.
7. Check that replaced wires do not contact sharp 5. Keep safety for hazardous invisible Laser Radiation,
edged or pointed parts. DO NOT watch the Laser Beam (Objective lens)
8. Also check areas surrounding repaired locations. directly.
9. Make sure that foreign objects (screws, solder 6. Models for some countries, laser warning labels are
droplets, etc.) do not remain inside the set. affixed on the unit and inside of the unit, as shown
MAKE YOUR CONTRIBUTION TO PROTECT below. Read it carefully for your safety, when
THE ENVIRONMENT repairing or adjusting the unit.
Used batteries with the ISO symbol for recycling
as well as small accumulators (rechargeable
batteries), mini-batteries (cells) and starter
batteries should not be thrown into the garbage
can.
Please leave them at an appropriate depot. All other house-
hold batteries can be thrown out with the household waste.
SAFETY CHECK AFTER SERVICING
After servicing, make measurements of leakage-current
or resistance in order to determine that exposed parts
are acceptably insulated from the supply circuit.
The leakage-current measurement should be done
between accessible metal parts (such as chassis,
ground terminal, microphone jacks, signal input/output
connectors, etc.) and the earth ground through a
resister of 1500 ohms paralleled with a 0.15
capacitor, under the unit's normal working conditions.
4
MEASUREMENTS AND ADJUSTMENTS

ALIGNMENT INSTRUCTIONS
EQUIPMENT NEEDED:
AM Signal Generator
FM Signal Generator
Oscilloscope
VTVM(AC, DC)
Test loop antenna (AM Adjustment)
Dummy antenna (FM Adjustment)
Distortion analyser

IMPORTANT
1. Check power-source voltage.
2. Set the function switch to band aligned.
3. Keep the signal input as low as possible to adjust accurately.
4. Modulation and modulation frequency.

Item
Modulation Modulation frequency
Band

AM 30% 400Hz

100% (40 kHz Dev.) [E/UK]

FM 400Hz
100% (75 kHz Dev.) [US]

ADJUSTMENT POINT

AM LOOP ANT FM ANT

<PACK DETAIL>
(FOR EUR version)
ANT TERMINAL
L2 L1 L1
FM ANT COIL
PACK1 L2
L4 L3

L104 CT10 L105

L5 L3
IFT L4 FM RF COIL
L6

J205 L5
L7 L6
L7 FM OSC COIL
J207 (FOR UL version)

L3 L3 FM ANT COIL
L5 L4

T102 L6 L4
IC12

T1 L5 FM RF COIL
L6
VR13

T101 L7 FM OSC COIL

L7
T1 FM IFT
VR11

CT10 AM ANT TRIMMER (1503kHz/1510kHz)

J208

L104 AM ANT COIL

VR12

L105 AM OSC COIL

T101 FM IFT COIL
T102 AM IFT COIL (612kHz/610kHz)
IC11 VR13 FM SD ADJUSTMENT
VR12 AM SD ADJUSTMENT
VR11 FM SEPARATION ADJ
J208 FM/AM VT
J205
FM OFFSET ADJ TP
J207

5
1. TUNING FREQUENCY RANGE ADJUSTMENTS
(FM) DC VOLTMETER ................ CONNECT TO TEST POINT J208 and GND

NO. Band Frequency Adjust for Adjustment

1 FM 87.50MHz 1.6V L7

J208 2 AM 530 kHz 1V L105

[US/C] [530 kHz] [1V] [L105]

2. AM TRACKING ADJUSTMENT
Signal Generator ........................ Connects to the AM ANT. Coil through the loop antenna.
Adjust for the indication of VTVM of the wave form of scope to be maximum.

BAND Step Frequency Adjust for Adjustment

1 610 kHz Maximum sensitivity T102, L104
[US/C] [610 kHz] Maximum sensitivity T102, L104
AM 2 1510 kHz Maximum sensitivity CT10
[US/C] [1510 kHz] Maximum sensitivity CT10
3 Repeat steps 1 and 2 several times.

3. FM-RF ADJUSTMENT
Signal Generator ........................ Connect to FM ANT JACK (FM IN) through the dummy.

NO. Frequency Adjust for Adjustment

1 90.10MHz Maximum Sensitivity L3, L5, L6

2 Repeat step 1 several times.

6
4. FM MONO DISTORTION ADJUSTMENT
DC VOLT METER ........................Connect to J205 (-), J207 (+) through the chock coil (100uH).
Signal Generator ........................Connect to FM ANT Jack (FM IN) through the dummy.
Distortion Meter .........................Connect to the output.

NO. Frequency Adjust for Adjustment

1 100.10MHz
DC Voltmeter 0V T101

J205
2 100.10MHz DC Voltmeter 0V
T101
J207 Minimum T.H.D
3 Repeat steps 1 and 2 several times.

5. FM/AM AUTO STOP LEVEL ADJUSTMENT

FM Signal Generator..................Connect to FM ANT Jack (FM IN) through the dummy.
AM Signal Generator .................Connect to AM ANT. Coil through the Loop antenna.

BAND Step Signal Generator Adjust for Adjustment

1 990KHz 82dB TUNED Display ON VR12
AM
[US/C] [990KHz]
2 990KHz 81dB TUNED Display OFF VR12
[US/C] [990KHz]
FM 1 100.1MHz 32dB TUNED Display ON VR13

2 100.1MHz 31dB TUNED Display OFF VR13

7
FIP DISPLAY

ANODE CONNECTION
10G 9G 8G 7G 6G 5G 4G 3G 2G 1G
P1 SOURCE d2 d2 d2 d2 d2 d2 d2 d2 kHz
P2 AUX d1 d1 d1 d1 d1 d1 d1 d1 1d
P3 LD e e e e e e e e 1e
P4 DVD r r r r r r r r 1c
P5 VCR 1 p p p p p p p p 1g
P6 REC n n n n n n n n 1f
P7 c c c c c c c c 1b
P8 SP. f f f f f f f f 1a
P9 A g g g g g g g g M
P10 B m m m m m m m m 2d
P11 CHURCH h h h h h h h h 2e
P12 DISCO j j j j j j j j 2c
P13 STADIUM k k k k k k k k 2g
P14 HALL b b b b b b b b 2f
P15 THEATER a2 a2 a2 a2 a2 a2 a2 a2 2b
P16 PCM a1 a1 a1 a1 a1 a1 a1 a1 2a
P17 AC-3 S1 S1 S1 S1 S1 S1 S1 S1 DELAY.T
P18 STEREO S2 S2 S2 S2 S2 S2 S2 S2 PRESET CH.
P19 3 S3 S3 S3 S3 S3 S3 S3 S3 MEMO
P20 S4 S4 S4 S4 S4 S4 S4 S4 TAPE
P21 DIGITAL RDS Dp TA MHz
P22 PRO LOGIC DTS TUNED STEREO PTY RT TP mS

8
PIN CONNECTION

47 1

Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Connection F2 F2 NP NX NX NX NX P22 P21 P20 P19 P18 P17 P16 P15

Pin No. 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

Connection P14 P13 P12 P11 P10 P9 P8 P7 P6 P5 P4 P3 P2 P1 NX

Pin No. 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45

Connection NX NX NX NX 1G 2G 3G 4G 5G 6G 7G 8G 9G 10G NP

Pin No. 46 47

Connection F1 F1

9
IC PIN FUNCTION (u-COM : ANAM1308AT,O.T.P :TMP87PM78F) : IC71

PIN No. SYMBOL I/O DESCRIPTION

1,25 VDD - Power Supply Port(+5V)
2,3 Function SW1,SW2 I Function Encoder Control Port
4 Speaker ON/OFF O Front Speaker Relay Drive Port(“H”)
5 NC - Not Use(No connection)
6 DSP Reset O Reset (Initial Clear) Port for YSS912
7 Surr. CLK O Surr. CLK Output Port
8 DATA OUT O Data Output Port for YSS912
9 Surr. DATA O Surr. DATA Output Port
10 CS O Chip Selector Port for YSS912
11 CS O Chip Selector Port for AK4112
12 CSBN O Sub DSP Chip Selector for YSS912
13,14 RDS CLK/DATA I RDS IC(SA6579TV1) CLK/DATA Port
15 Stereo IN I Stereo Display Control Port("L")
16 Tuned IN I Tuned Display Control Port("L")
17 ~ 21 KEY Matrix I Resistor Divide Key Control Input (17,18 Pin: NOT USE)
22,30 Vss - Device GND Port
23 Vass - Device Analog GND Port
24 Varef - A/D Converter Reference Voltage
26 BACKUP I Back Up Mode Control Input
27 TEST - NC(GND)
28,29 VOLUME UP/DOWN I Master Volume Up/Down Control Port
31 X IN I
8MHz Crystal Connection Port
32 X OUT O
33 RESET (L) I Reset Input
34 REMOTE IN I Remote Control Sensor Data Input
35 BUS IN(NC) I System Remote Control Input(No Connection))
36 HEADPHONE IN O Headphone JACK INPUT(“H”) - Connet to GND
37 E.VOL.DATA O
38 E.VOL.CLK I Electronic Vol. IC(M62446FP) DATA/CLK/STB Port
39 E.VOL.CE O
40 PLL.DATA IN I PLL IC (LC72131) DATA Input Port
41 PLL.CE O PLL IC (LC72131) Chip Enable Control Port
42 DATA 3 O Function IC Data Input Port
43 CLK 3 O Func./PLL IC CLK Control Port
44 FUNC. STB O Function Strobe Control Output
45 FUNC. MUTE O Function Mute Control Output(“H”)
46 SURR. MUTE O Surrounc Mute Control Output(“H”)
47 Power ON/OFF O Power ON/OFF Control Port("H")
48 SURR. H O Surr. ON/OFF Contol Port("H")
49 PROTECT IN I Protect Input Port("L")
50 FIP Vkk - FIP (FLT) -28V Negative Power Supply For FIP Blinking
51 ~ 60 FIP Grid O FIP (FLT) Grid Control Outputs
61 ~ 82 FIP Segment O FIP (FLT) Segment Control Outputs
83 ~ 86 Option l Area/Function Option Ports
87 ~ 94 N.C - Not Use(No connection)
95 SUB. LED O Subwoofer LED Drive Port
96 MUTE LED O MUTE LED Drive Port
97 ~ 99 VIDED A/B/C O Video IC(NJM2296M/LA7952) Control Ports
100 N.C - Not Use(No connection)

10
11
 Dolby Digital/Pro Logic DTS DECODER (YSS912C:INPUT IC43)

PIN No. SYMBOL I/O DESCRIPTION

1,31,71 VDD1 - +5V Power Supply(for I/Os)
2 RAMCEN O External SRAM interface /CE
3 RAMA16 O External SRAM interface address 16
4 RAMA15 O External SRAM interface address 15
5 SDIB0 I+ PCM input 0 to Sub DSP(not use)
6 SDIB1 I+ PCM input 1 to Sub DSP(not use)
7 SDIB2 I+ PCM input 2 to Sub DSP(not use)
8 XI I+
Crystal oscillator connection(12.288MHz)
9 XO O
10, 30 VSS - Ground
11 AVDD - +3.3V power supply (for PLL circuit)
12 SDIB3 I+ PCM input 3 to Sub DSP(not use)
13 TEST - Test terminal(to be open in normal use)
14 TEST - Test terminal(to be open in normal use)
15 OVFB O Detection of overflow at Sub DSP (not use)
16 DTSDATA O Detection of DTS data (not use)
17 AC3DATA O Detection of AC-3 data (not use)
18 SDOB3 O PCM output from Sub DSP
19 CPO A Output terminal for PLL,to be connected to ground through the external analog filter circuit
20 AVSS - Ground for PLL circuit)
21,41,51,81,91 VDD2 - +3.3V power supply (for core logic)
22 SDOA2 O PCM output from Main DSP (C,LFE)
23 SDOA1 O PCM output from Main DSP (LS,RS)
24 SDOA0 O PCM output from Main DSP (L,R)
25 ~ 29 RAMA 14~10 O External SRAM interface address 14~10
32 ~ 35 OPORT 0~3 O Output port for general purpose
36 ~ 39 OPORT 4~7 O Output port for general purpose (not use)
40,50,60,80,90,100 VSS - Ground
42 ~ 44 RAAM 9~7 O External SRAM interface address 9~7
45 ~ 47 SDOB 2~0 O PCM output from Sub DSP
48 SDBCK1 I+ Bit clock input for SDOA,SDIB,SDOB (not use)
49 SDWCK1 I+ Word clock input for SDOA,SDIB,SDOB (not use)
52 NONPCM O Detection of non-PCM data (not use)
53 CRC O Detection of AC-3 CRC error (not use)
54 MUTE O Detection of auto mute (not use)
55 KARAOKE O Detection of AC-3 karaoke data (not use)
56 SURENC O Detection of AC-3 2/0 mode Dolby surround encoded input (not use)
57 /SDBCK 0 O Inverted SDBCK0 clock output (refer to Block diagram)
58 RAMA6 O External SRAM interface address 6
59 RAMA5 O External SRAM interface address 5
61 RAMA4 O External SRAM interface address 4
62 /IC Is Initial clear
63 TEST - Test terminal (to be ofen in normal use)
64 RAMA3 O External SRAM interface address 3
65 /CSB Is+ Sub DSP Chip select
66 /CS Is Microprocessor interface Chip select input
67 SO Ot Microprocessor interface serial data output
68 SI Is Microprocessor interface /Sub DSP Serial data input
69 SCK Is Microprocessor interface /Sub DSP clock input

12
PIN No. SYMBOL I/O DESCRIPTION
70 RAMA2 O External SRAM interface address 2
72 ~ 79 RAMD0~7 I+/O External SRAM interface data (STREAM0~7 output when External SRAM is not in use)
82 SDWCK0 I Word clock input for SDIA, SDOA, SDIB, SDOB
83 SDBCK0 I Bit clock input for SDIA,SDOA,SDIB,SDOB
84 SDIA0 I AC-3 Bitstream (or PCM) data input for Main DSP
85 SDIA1 I AC-3 Bitstream (or PCM) data input for Main DSP
86 RAMA1 O External SRAM interface address 1
87 RAMA0 O External SRAM interface address 0
88 RAMWEN O External SRAM interface /WE
89 RAMOEN O External SRAM interface /OE
92 ~ 99 IPORT7~0 I+ Input port for general purpose (not use)

NOTE) Is: Schmidt trigger input terminal It: Input terminal with pull-up resistor
O: Digital output terminal Ot: Tri-state digital output terminal
A: Analog terminal

YSS912C PIN CONFIGURATION

RAMWEN
RAMOEN

SDWCK0
SDBCK0
IPORT0
IPORT1
IPORT2
IPORT3
IPORT4
IPORT5
IPORT6
IPORT7

RAMA0
RAMA1
SDIA1
SDIA0
VDD2

VDD2
VSS
VSS

100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81
VDD1 1 80 VSS
RAMCEN 2 79 RAMD7
RAMA16 3 78 RAMD6
RAMA15 4 77 RAMD5
SDIB0 5 76 RAMD4
SDIB1 6 75 RAMD3
SDIB2 7 74 RAMD2
XI 8 73 RAMD1
XO 9 72 RAMD0
VSS 10 71 VDD1
AVDD 11 70 RAMA2
SDIB3 12 69 SCK
TEST 13 68 SI
TEST 14 67 SO
OVFB 15 66 /CS
DTSDATA 16 65 /CSB
AC3DATA 17 64 RAMA3
SDOB3 18 63 TEST
CPO 19 62 /IC
AVSS 20 61 RAMA4
VDD2 21 60 VSS
SDOA2 22 59 RAMA5
SDOA1 23 58 RAMA6
SDOA0 24 57 /SDBCK0
RAMA14 25 56 SURENC
RAMA13 26 55 KARAOKE
RAMA12 27 54 MUTE
RAMA11 28 53 CRC
RAMA10 29 52 NONPCM
VSS 30 51 VDD2
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
VDD1
OPORT0
OPORT1
OPORT2
OPORT3
OPORT4
OPORT5
OPORT6
OPORT7
VSS
VDD2
RAMA9
RAMA8
RAMA7
SDOB2
SDOB1
SDOB0
SDBCK1
SDWCK1
VSS

13
14
IPORT 0~7
/CS
SO
SI
SCK
OPORT 0~7
/CSB
SCK

SI
Microprocessor Coefficient
Interface Program RAM
YSS912C BLOCK DIAGRAM

Control Signals Control Signals

Control Registers SDBCK1

SDWCK1
/SDBCK0
SDBCK0
SDWCK0

SDOACKSEL SDOBCKSEL SDOBCKSEL

L,R
SDOB0
LS,RS
SDIA0 SDOB1
C, LFE
SDIBSEL

24 * 16
24 * 16

decoder
SDOB2
Sub DSP

SDIASEL
Main DSP

Input Buffer
SDIA1

SDIA Interface
SDIB Interface

SDOA Interface
SDOB Interface

AC-3/Pro Logic/DTS
SDOB3

SURENC STREAM 0~7

External RAM
KARAOKE Operating clock interface
MUTE Data RAM
(30MHz)
CRC
AC3DATA ERAMUSE
Delay RAM

SDIA Interface
DTSDATA PLL
NONPCM

XI
XO
CPO
OVFB

SDIB0
SDIB1
SDIB2
SDIB3

SDOA0
SDOA1
SDOA2
RAMCEN
RAMOEN
RAMWEN

RAMA 0~7
RAMA 0~16
M62446FP (ELECTRONIC VOLUME/INPUT IC31)

OUT4 1 42 DVoo

OUT3 2 OUTPUT 41 CLK

PORT volume
OUT2 MCU I/F
3 40 DATA

OUT1 4 39 LATCH

AVoo 5 volume 38 DGND

SWin 6 37 AGND

GNDS 7 36 SWout
volume
SRin 8 35 SRout

SLin 9 34 SLout

GNDC 10 33 Cout
volume
Cin 11 32 Rout

GNDR 12 31 Lout

Rin 13 volume 30 AVss

GNDL 14 29 CL1

Lin 15 28 CL2

BYPASSR 16 volume 27 CR1

BYPASSL 17 26 CR2

LTRE 18 25 RTRE

LBASS3 19 tone tone 24 RBASS3

LBASS2 20 23 RBASS2

LBASS1 21 22 RBASS1

AV4527VQ (ADC/DAC/INPUT IC42)

RX1 RX2 RX3 RX4

Audio
LIN+ I/F XTI
LIN- ADC HPF XTO
RIN+ MCLK DIR
ADC HPF MCLK MCKO
RIN- LRCK LRCK AK4110
BICK
BICK
LRCK DAUX
LOUT1 LPF DAC DATT SDTO
BICK
FOMAT
ROUT1 LPF DAC DATT CONVERTER
SDOUT
LRCK
LOUT2 LPF DAC DATT SDOS
SDIN1 BICK
AC3
SDIN2 SDTO
ROUT2 LPF DAC DATT SDIN3 SDIN
SDTI1
SDOUT1
SDTI2
LOUT3 LPF DAC DATT SDOUT2
SDTI3
SDOUT3
ROUT3 LPF DAC DATT AK4527

15
 PIN ASSIGNMENT (74HCU04AFN : IC40 )

1A 1 14 Vcc
1Y 2 13 6A
2A 3 12 6Y
2Y 4 11 5A
3A 5 10 5Y
3Y 6 9 4A
GND 7 8 4Y

LOGIC SYMBOL

(1) (2)
1A 1Y
(3) (4)
2A 2Y
(5) (6)
3A 3Y
(9) (8)
4A 4Y
(11) (10)
5A 5Y
(13) (12)
6A 6Y

TRUTH TABLE

A Y
L H
H L

16
AK4112AVF (DIR/INPUT IC41)

AVSS AVDD R MCKO1 MCKO2 XTI XTO

RX1 Clock Clock X’tal

RX2 Input Recovery Generator Oscillator
RX3 Selector
RX4 96kHz FS96
Detect
DAUX
LRCK
Audio BICK
V/TX DAIF SDTO
DEM I/F
Decoder

DVDD
DVSS
TVDD
CSN
System uP CCLK
Control AC-3/MPEG Error I/F CDTO
PDN Detect Detect CDTI

AUTO ERF P/S="L"

[Serial Control Mode]

AVSS AVDD R MCKO1 MCKO2 XTI XTO

Clock Clock X’tal

RX1 Recovery Generator Oscillator

96kHz FS96
Detect
DAUX
LRCK
BICK
V DAIF SDTO
DEM
Decoder Audio DIF0
I/F DIF1
DVDD DIF2
DVSS 4
TVDD
OCKS0
OCKS1 OCKSO
CMO System OCKS1
CM1 Control AC-3/MPEG Error CM0
PDN Detect Detect CM1

AUTO ERF P/S="H"

[Parallel Control Mode]

17
LC72131 (PLL SYNTHESIZER/ TUNER IC11)

XIN REFERENCE PHASE DETECTOR PD

DIVIDER CHARGE PUMP
XOUT

AIN
SAMLLOM COUNTER UNLOCK
FMIN 1/16, 1/17 4bits DETECTOR AOUT

12bits PROGRAMMABLE
AMIN DIVIDER

CE

DI CCB
DATA SHIFT REGISTER UNIVERSAL
IFIN
LATCH COUNTER
I/F
CL

DO
POWER
VDD ON
RESET
VSS

BO1 BO2 BO3 BO4 I01 I02

LA1837 (MPX + IF / TUNER IC12)

AM SD
ADJ

3 rd 5 th
DECODER
ANTI-BIRDIE
FM

18
KIC9164AF (FUNCTION/INPUT IC20)

BLOCK DIAGRAM
Vss GND VDD
1 14 28

L-S 1 2 27 R-S 1

L-S 2 3 26 R-S 2

L-COM 1 4 25 R-COM1

L-S 3 5 24 R-S 3

LATCH CIRCUIT
LEVEL SHIFTER

LEVEL SHIFTER
LATCH CIRCUIT
L-S 4 6 23 R-S 4

L-COM 2 7 22 R-COM2

L-S 5 8 21 R-S 5

L-S 6 9 20 R-S 6

L-COM 3 10 19 R-COM3

L-S 7 11 18 R-S 7

L-COM 4 12 17 R-COM4

ST 13 16 DATA

15 CK
SHIFT REGISTER

KIC9163AF (FUNCTION/INPUT IC21)

BLOCK DIAGRAM

Vss GND VDD

1 14 28

L-S 1 2 27 R-S 1

L-S 2 3 26 R-S 2

L-COM 1 4 25 R-COM1

L-S 3 5 24 R-S 3
LATCH CIRCUIT
LEVEL SHIFTER

LEVEL SHIFTER
LATCH CIRCUIT

L-S 4 6 23 R-S 4

L-COM 2 7 22 R-COM2

L-S 5 8 21 R-S 5

L-S 6 9 20 R-S 6

L-COM 3 10 19 R-COM3

L-S 7 11 18 R-S 7

L-COM 4 12 17 R-COM4

ST 13 16 DATA

15 CK
SHIFT REGISTER

19
 BLOCK DIAGAM (NJM2296M /MAIN IC96)

V+ SW2 SW1 SW5

16 10 14 2

Vin1 13
20K

S5
Vin2 9 S1
6.2dB
Amp
75
dirver 1 Vout1
20K S2
20K

Vin3 7 S6
S4
20K 6.2dB 75
Amp dirver 15 Vout2
20K
Vin4 5
20K S3
6.2dB 75
S7 Amp dirver 11 Vout3
Vin5 3
20K 20K

4 6 12 8

SW3 SW4 V-
GND

LA6462M/6458M

PIN CONFIGURATION

• PIN FUNCITON
1 8
1. A OUTPUT
A 2. A-INPUT
2 7 3. A+INPUT
B 4. V
5. B+INPUT
3 6
6. B-INPUT
7. B OUTPUT
4 5 8. V

LA6462M/
LA6458M

20
TRANSISTOR, REGULATOR IC BLOCK DIAGRAM

TO-92S TO-92 TO-220 TO-92L

1. Emitter 1. Emitter 1. INPUT 1. Emitter

2. Collector 2. Collector 2. OUTPUT 2. Collector
3. Base 3. Base 3. GND 3. Base
123 123
123 123

KSA1175Y KRC114M KTD1302T KTA1268GR MC7912C KSA916Y KSC2316Y

KTA1271Y KSD811Y KTC3200GR KSC2785Y
DTC144ES DTA144ES KTC31940
DTA114YS DTC114YS
DTC143TS DTA144TS

TO-126 TO-220 TO-220 TO-3P

1. Emitter 1. Base 1. INPUT 1. Base

2. Collector 2. Collector 2. GND 2. Collector
3. Base 3. Emitter 3. OUTPUT 3. Emitter

123 123 123 1 2 3

2SC4137V 2SC34230 KSA614Y KSD288Y MC7812C MC7805C 2SC4468

2SA1360O 2SB1186AE 2SD1763AE 2SA1695

LA7952(I.C, Video sw/ Input: IC51, IC52)

BLOCK DIAGAM/ PIN CONFIGURATION

6dB
amp

video switch
driver control
(4 input 1 output)

1 2 3 4 5 6 7 8 9
VIDEO A B VIN1 GND VIN2 VCC VIN3 VIN4

21
 EXPLODED VIEW (AG-D9260)

36
35
S4
S5
S10 x21
24
S13
40

S4
32
34

33
S11 x4

S5 x5
S13 x2
S12 x2
S6 x2 S4
S7 x2

30 x2
37 S7 x4

S6 x4
S7 x2

25 x2 S13 x2
38
8
S7 x2
42
N0. DESCRIPION PARTS-No. Q,ty
41 1 FRONT PANEL CGW2A287YH10 1
26
12 2 BADGE KGB1A056H12 1
3 STANDBY KNOB KBT2A450 1
7 4 MODE KNOB CBT1A723 2
27 5 TONE KNOB CBT1A724 1
6
31 6 PHONES PCB ASS'Y 1
x2 7 PCB BRACKET KMK1A010 1
3
S4 x5 29 8 FRONT PCB ASS'Y 1
19 S4 x2
x2 9 JACK PCB ASS'Y 1
S1 x11
1 S1 28 10 VOLUME PCB ASS'Y 1
S1 x2
x2 S1 11 LED SHEET KGX1A293Z 1
2 12 POWER KNOB KBC1A095 1
S5 13 LED SHEET(3P) KGX1A243X 1
x2
14 WASHER 2
15 NUT 2
16 VOLUME KNOB KBN1A082K76 2
4 x2 23 x2
17 BALANCE KNOB KBN2A083Z 3
S13 18 WINDOW FIP CGU1A235A5Y 1
x2
19 TOP BRACKET KMD1A355 2
20 BOTTOM CHASSIS CUA1A185 1
21 FOOT FRONT KKL2A042H11 2
22 CUSHION FOOT KHG1A050 2
S1 x2 23 FOOT RUBBER KKL1A012 2
24 REAR PANEL CKF3A203Z 1
25 HOLDER PCB KHE170 2
11 20 26 CUSHION SUPPORT KHG1A104 1
27 MAIN PCB ASS'Y
13 No. DESCRIPION PARTS-No. Q,ty 28 HEAT SINK KMY1A161 1
21 x2 S1 SCREW KTB3+10G 18 29 PCB BRACKET KMD1A417 2
18 S1 S2 SCREW KTB3+14J 30 PCB BRACKET KMD1A416 2
x2 22 x2
S3 SCREW KTB3+6JFZ 31 WIRE HOLDER PCB 2
S13 x2 S4 SCREW KTB3+6J 8 32 INPUT PCB ASS'Y 1
39 S5 SCREW KTB3+8JFZ 15 33 TRANS PCB ASS'Y 1
10 x2
S6 SCREW KTB4+6FFZ 6 34 TR BRACKET KMD1A350 1
17 x3 9 S7 7 35 AC CORD KJA2A013Z 1
x2 SCREW KTB3+8J
S8 SCREW KTB4+10JFZ 36 AC CORD BUSHING KHR1A028 1
5 x2 S9 SCREW KTWS3+10G 37 TOP CABINET KKC1B109S1 1
19 S10 SCREW KTB3+10GFZ 21 38 RUBBER KHG1A113 4
14 x2
S11 SCREW KTB4+8F 4 39 FUNCTION KNOB CBN1A127 1
15 S5 x2 S12 SCREW KTW3+12J 2 40 SPEAKER JACK PCB ASS'Y 1
16 S13 SCREW KTW3+8J 13 39 POWER BRACKET KMD1A415 1
S5 x5 S14 SCREW KTB3+10J 40 POWER PUSH PCB ASS'Y 1

22
EXPLODED VIEW
REF.NO. PARTS NO. DESCRIPTION REF.NO. PARTS NO. DESCRIPTION
1 9A08904800 PANEL,FRONT [US,C,UK(B)] 38 9A08885700 RUBBER
9A08904810 PANEL,FRONT [E] 39 9A08904200 KNOB,FUNCTION [Except UK(N)]
9A08959600 PANEL,FRONT [UK(N)] 9A08958500 KNOB,FUNCTION [UK(N)]
2 9A07047400 BADGE [Except UK(N)] 40 ---------- SPEAKER JACK PCB ASSY
9A08887100 BADGE [UK(N)] 41 9A08957700 BRACKET,POWER [UK]
42 ---------- POWER PUSH PCB ASSY
3 9A06777500 KNOB,POWER [Except UK(N)]
9A08959500 KNOB,STANDBY [UK(N)] 9A08038100 RING,FERRITE
4 9A08904600 KNOB,MODE [Except UK(N)] CN10 9A08887300 CABLE,CARD
9A08959300 KNOB,MODE [UK(N)] CN11 9A08887400 CABLE,CARD
5 9A08904700 KNOB,TONE [Except UK(N)] F901 £ 9A06756100 FUSE,2.5A 250V [US,C,E]
9A08959400 KNOB,TONE [UK(N)]
F902 £ 9A06537400 FUSE,4A 250V [E,UK]
6 ---------- PHONES PCB ASSY F902 £ 9A07371000 FUSE,6.3A 250V [US,C]
7 9A08886900 BRACKET,PCB F903,F904 £ 9A07044800 FUSE,8A 250V
8 9A08905000 FRONT PCB ASSY [US,C]
9A08905010 FRONT PCB ASSY [E,UK]
9 ---------- JACK PCB ASSY
Note
10 ---------- VOLUME PCB ASSY UK(B): Black Version, UK(N): Gold Version
11 9A08887200 SHEET,LED
12 9A06783600 KNOB,POWER [E,UK(B)]
9A08959100 KNOB,POWER [UK(N)]
13 9A08045300 SHEET,LED(3P)

16 9A07045100 KNOB,FUNCTION [Except UK(N)]

9A08958400 KNOB,VOLUME [UK(N)]
17 9A08937100 KNOB,BASS [Except UK(N)]
9A08958600 KNOB,ROTARY [UK(N)]
18 9A08904300 WINDOW,FIP

19 9A08886800 BRACKET,TOP
20 9A08888100 CHASSIS,BOTTOM
21 9A08887600 FOOT,FRONT
22 9A06754800 RUBBER,CUSHION
23 9A06755300 FOOT,RUBBER(BLACK)

24 9A08938900 PANEL,REAR [US,C]

9A08938910 PANEL,REAR [E]
9A08938920 PANEL,REAR [UK]
25 9A01375500 PCB HOLDER
26 9A06327100 SUPPORT,CUSHION

27 9A08939400 MAIN PCB ASSY [US,C]

9A08939410 MAIN PCB ASSY [E]
9A08939420 MAIN PCB ASSY [UK]
28 9A08952200 HEAT SINK
29 9A08952300 BRACKET,PCB

30 9A08745400 BRACKET,PCB(H/T)
31 ---------- WIRE HOLDER PCB
32 9A08939500 INPUT PCB ASSY [US,C]
9A08939510 INPUT PCB ASSY [E,UK]

33 £ 9A08904000 TRANSFORMER,POWER [E,UK(B)]

£ 9A08939300 TRANSFORMER,POWER [US,C]
£ 9A08959700 TRANSFORMER,POWER [UK(N)]
34 9A08887800 BRACKET,TR

35 £ 9A07872600 POWER CORD [US,C]

£ 9A07916800 POWER CORD [UK]
£ 9A08956900 POWER CORD [E]
36 £ 9A06754900 BUSHING,AC CORD
37 9A08810200 CABINET,TOP [Except UK(N)]
9A08885800 CABINET,TOP [UK(N)]

23
24
25
26
INPUT PCB ASSY FRONT PCB ASSY
REF.NO. PARTS NO. DESCRIPTION REF.NO. PARTS NO. DESCRIPTION
9A08939500 INPUT PCB ASSY [US,C] 9A08905000 FRONT PCB ASSY [US,C]
9A08939510 INPUT PCB ASSY [E,UK] 9A08905010 FRONT PCB ASSY [E,UK]
9A08953300 INPUT PCB 9A08905200 FRONT PCB
9A08215300 PACK,FRONT END [US,C] BK71,BK72 9A08888700 BRACKET,FLT
9A08957300 PACK,TUNER [E,UK] CH94,CH95 9A08889400 CONNECTOR,HOUSING

ANT1 9A07371900 TERMINAL,ANT [US,C] CN10 9A08889500 WAFER,CARDCABLE

ANT1 9A08957400 TERMINAL,ANT [E,UK] CN11 9A08889600 WAFER,CARDCABLE
BN13,BN14 9A08036700 WAFER CN16 9A08036300 WAFER
CF11,CF12 9A06544600 FILTER,CERAMIC E107MSHAT CN17 9A07335100 WAFER,MOLEX 53015
CF22 9A07006300 FILTER,CERAMIC PBF450JR3 CN71 9A07049700 WAFER

CN10 9A08947300 WAFER,CARDCABLE CN74 9A07049500 WAFER,MOLEX 53015-0310

CN11 9A08947400 WAFER,CARDCABLE CN83 9A05329100 WAFER,MOLEX 5267-03A
CN41 9A05356300 WAFER,04GA19ZM CN90 9A06785000 WAFER [E,UK]
CT10 9A01405900 C,VARIABLE 20PF CN91 9A06759300 WAFER
D101 9A08163000 DIODE,VARICAP SVC342-L-AA CN92 9A05329300 WAFER,MOLEX 5267-04A

D110,D113 9A08878200 DIODE,1SS133T-77 CW13,CW14 9A08036600 WAFER,MOLEX 35336-1010

D150 9A07892400 DIODE,ZENER 9.1V 1/2W C931 £ 9A08882700 C,CERAMIC(KH TYPE) [E,UK]
D190 9A08954100 DIODE,ZENER MTZJ5.1BT D701-D703 9A08147300 LED,SLR342VCTB7(RED)
D301,D302 9A08951100 DIODE,ZENER MTZJ6.8BT D704-D707 9A08878200 DIODE,1SS133T-77
D303 9A08954100 DIODE,ZENER MTZJ5.1BT D901 £ 9A08889700 DIODE,BRIDGE

D401 9A08954200 DIODE,1N4148T D903-D908 £ 9A05194700 DIODE,1N4003ST

D451 9A08954300 DIODE,ZENER MTZJ4.7BT D911 9A08905700 DIODE,ZENER MTZJ30BT
IC11 9A08947500 IC,PLL D912 9A07887100 DIODE,ZENER 6.2V
IC12 9A08033000 IC,LA1837 EP71 9A05961500 PLATE,EARTH
IC20 9A08947600 IC,KIC9164AF FIP1 9A08034600 FIP,SVA-10MS11

IC21 9A08947700 IC,KIC9163AF F903,F904 9A05328200 HOLDER,FUSE

IC22 9A08889900 IC,LA6462M IC71 9A08889800 IC,TMP87PM78F
IC23-IC26 9A08947800 IC,LA6458M IC73 9A08889900 IC,LA6462M
IC31 9A08947900 IC,M62446FP IC74 9A08033400 IC,SAA6579T/V1 [E,UK]
IC32,IC34 9A08889900 IC,LA6462M JK71-JK73 9A08890000 JACK,VCR

IC33,IC35 9A08947800 IC,LA6458M JK73 9A07491600 JACK

IC40 9A08948000 IC,TC74HCU04AFN L701 9A07886600 COIL,10UH
IC41 9A08948100 IC,AK4112A-VF-E2 Q701 9A08905800 TR,KRA104MT
IC42 9A08903900 IC,AK4527VQ Q702 9A08905900 TR,KRC114MT
IC43 9A08033700 IC,YSS912C-F Q703,Q704 9A08878300 TR,KRC107M

IC45 9A08032900 IC,IS61C256AH-15J Q705 9A07887900 TR,KSB811YT

IC51,IC52 9A08948200 IC,LA7952 Q706-Q708 9A08878300 TR,KRC107M
JK11,JK12 9A07425400 JACK,IN/OUT Q901 9A08906000 TR,KTA1271YT
JK13 9A07425500 TERMINAL,IN/OUT RS71 9A08563600 SENSOR,REMOCON
JK15,JK16 9A08948300 MODULE,OPTICAL TORX178A R901-R904 £ 9A05897200 R,FUSE 0.47 OHM 1W

JK17 9A08948400 JACK,BOARD(2P) SW91 £ 9A06784700 SW,PUSH [E,UK]

JK51 9A08948500 JACK,S-VIDEO(3P/H) S701-S718 9A07878500 SW,TACT SKHV10910G
L104 9A08948600 COIL,MW ANT VE71 9A08890200 VR,ENCODER 2A004Z
L105 9A07873300 COIL,AM OSC VE72 9A08890300 VR,ENCODER 2A006Z
L108,L109 9A08957500 COIL,MPX [E,UK] VR71 9A08890400 R,VARIABLE(BALANCE)

L403 9A08037600 COIL,10UH J VR72,VR73 9A08890500 R,VARIABLE(TONE)

L405,L408 9A08037600 COIL,10UH J X701 9A08879000 CRYSTAL
L406,L407 9A07050600 BEAD,CORE X702 9A07501700 CRYSTAL [E,UK]
Q106 9A08954400 TR,KTC3194OT
Q112 9A08884100 TR,KRA107M

Q114 9A08878300 TR,KRC107M

Q401 9A07888000 TR,KSC2316YT
R102 £ 9A08948700 R,CARBON 4.7 OHM 1/2W J
T101 9A08125500 IFT,FM
T102 9A08125400 IFT,AM

VR11,VR13 9A08040600 R,SEMI-FIXED 10K OHM

VR12 9A08040700 R,SEMI-FIXED 22K OHM
X101 9A08883700 CRYSTAL
X401 9A08949000 CRYSTAL

27
MAIN PCB ASSY MAIN PCB ASSY
REF.NO. PARTS NO. DESCRIPTION REF.NO. PARTS NO. DESCRIPTION
9A08939400 MAIN PCB ASSY [US,C] Q511-Q520 9A08951200 TR,KTA1268GRT
9A08939410 MAIN PCB ASSY [E] Q541-Q545 9A08951200 TR,KTA1268GRT
9A08939420 MAIN PCB ASSY [UK] Q556-Q565 9A08951300 TR,KTC3200GRT
9A08950900 MAIN PCB Q581-Q585 9A08951200 TR,KTA1268GRT
9A08952200 HEAT SINK Q611-Q615 9A08952400 TR,KTD600K

9A08745400 BRACKET,PCB(H/T) Q621-Q625 9A08946200 TR,2SA1360O

9A08952300 BRACKET,PCB Q626-Q630 9A08946300 TR,2SC3423O
CN17 9A06250600 WAFER,02GA19ZM Q642-Q645 £ 9A08946400 TR,KTD2061Y
CN73 9A05356500 WAFER,MOLEX 53014-0710 Q646-Q650 £ 9A08946500 TR,KTB1369Y
CN91 9A06674400 WAFER Q656 £ 9A08946400 TR,KTD2061Y

CN92 9A06785000 WAFER Q657-Q660 £ 9A08952600 TR,2SC4468

CN94,CN95 9A08891200 WAFER,08GA98ZM Q661-Q665 £ 9A08952700 TR,2SA1695
CN96 9A05330000 WAFER,MOLEX 5267-07A Q670 £ 9A08952600 TR,2SC4468
CN97 9A07049600 WAFER Q681-Q685 9A03745000 TR,KSC2785-YTA
CN98 9A05973000 WAFER,8P Q901,Q935 9A08884100 TR,KRA107M

CN99 9A05967700 WAFER Q938-Q940 9A08884100 TR,KRA107M

C903 £ 9A08032200 C,LINE ACROSS 0.1UF 250V Q942,Q943 9A03745000 TR,KSC2785-YTA
C904 £ 9A08882700 C,CERAMIC DE7150-610F472M Q951 9A08878300 TR,KRC107M
C906 £ 9A08944600 C,ELECT 1000UF 25V Q952 9A08884100 TR,KRA107M
C915,C916 £ 9A08944700 C,ELECT 8200UF 63V Q953-Q956 9A07888500 TR,KTD1302T

C917 £ 9A08944800 C,ELECT 3300UF 25V Q969-Q973 9A07888500 TR,KTD1302T

C918 £ 9A07897200 C,ELECT 2200UF 25V Q991 9A08878300 TR,KRC107M
C961 £ 9A08944900 C,ELECT 3300UF 16V Q992 9A08884100 TR,KRA107M
D501,D502 9A08878200 DIODE,1SS133T-77 RY93 £ 9A08946600 RELAY,4A004ZU
D507,D508 9A08878200 DIODE,1SS133T-77 RY94 £ 9A08946700 RELAY,1A008ZE

D511-D516 9A08878200 DIODE,1SS133T-77 R656-R660 £ 9A07331100 R,CEMENT 0.22X2 5W

D581-D585 9A08878200 DIODE,1SS133T-77 R904 £ 9A06761000 R,CARBON 3.3M K 1/2W [US,C]
D901 £ 9A05194700 DIODE,1N4003ST R905 £ 9A05338000 R,METAL 10 OHM 1W J
D902 9A08878200 DIODE,1SS133T-77 R907,R908 £ 9A07309700 R,METAL 470 OHM 1W J
D903-D906 £ 9A05194700 DIODE,1N4003ST R958,R959 £ 9A08946800 R,CARBON 120 OHM 1/2W J

D911,D912 9A08878200 DIODE,1SS133T-77 R993-R997 £ 9A05338000 R,METAL 10 OHM 1W J

D914-D917 9A08878200 DIODE,1SS133T-77 TH91 9A08039800 THERMAL SENSOR,POSISTOR
D931 9A08878200 DIODE,1SS133T-77 T901 £ 9A08956600 TRANSFORMER,SUB [US,C]
D951,D952 9A08951100 DIODE,ZENER MTZJ6.8BT T901 £ 9A08956610 TRANSFORMER,SUB [E,UK]
D953 9A08878200 DIODE,1SS133T-77

ET01 9A08945000 PLATE,EARTH

ET02 9A08945100 BRACKET,PCB
ET03 9A05333900 PLATE,EARTH
F901 9A05328200 HOLDER,FUSE [US,C,E]
F902 9A05328200 HOLDER,FUSE

IC91 9A08952900 HEAT SINK

IC91 £ 9A07898500 IC,KA7812-ABTU
IC92 9A08952900 HEAT SINK
IC92 £ 9A08953100 IC,KA7912-ABTU
IC93 9A08953200 HEAT SINK

IC93 £ 9A08218600 IC,KA7805-ABTU

IC95 £ 9A08218600 IC,KA7805-ABTU
IC96 9A08945500 IC,NJM2296M
JK93 9A08956300 TERMINAL,SPEAKER
JK94 9A08956400 JACK,LINE IN TERMINAL

JK97 9A07427800 JACK,VCR

JK98 9A08945800 JACK,BOARD
L501-L505 9A08946000 COIL,SPEAKER
OL01 £ 9A08946100 OUTLET,2P [US,C]
OL91 £ 9A08957100 OUTLET,2P [E]

28
INCLUDED ACCESSORIES
REF.NO. PARTS NO. DESCRIPTION REMARKS
9A08584400 OWNER'S MNL,E/F [US,C]
9A08523500 OWNER'S MNL,E/F/G/I/S [E,UK(B)]
9A08688800 OWNER'S MNL,E/F [UK(N)]
9A08763300 REMOTE CONTROL UNIT,UR-417

9A08886100 AM LOOP ANTENNA ASSY [US,C]

9A08880900 AM LOOP ANTENNA ASSY [E,UK]
9A08886000 ANT,FM T [US,C]
9A04883100 ANT,FM WIRE [UK]

29
 SCHEMATIC DIAGRAM AG-D9260
1 2 3 4 5 6 7 8

NOTES:
1. Resistor values are in ohms (k=kilo-ohms, M=megohms).
2. Capacitor values are in microfarads (p=picofarads).
3. £Parts marked with this sign are safety critical components.
They must always be replaced with identical components-refer
to the appropriate parts list and ensure exact replacement.
A

AG-D9260
AV Digital Home Theater Receiver
1 st Issue; June 2001
 SCHEMATIC DIAGRAM AG-D9260
1 2 3 4 5 6 7 8

NOTES:
1. Resistor values are in ohms (k=kilo-ohms, M=megohms).
2. Capacitor values are in microfarads (p=picofarads).
3. £Parts marked with this sign are safety critical components.
They must always be replaced with identical components-refer
to the appropriate parts list and ensure exact replacement.
A

AG-D9260
AV Digital Home Theater Receiver
1 st Issue; June 2001
 SCHEMATIC DIAGRAM AG-D9260
1 2 3 4 5 6 7 8

INSTRUCTIONS FOR SERVICE PERSONNEL

BEFORE RETURNING APPLIANCE TO THE CUSTOMER, MAKE LEAKAGE-
CURRENT OR RESISTANCE MEASUREMENTS TO DETERMINE THAT EXPOSED
NOTES:
1. Resistor values are in ohms (k=kilo-ohms, M=megohms).
2. Capacitor values are in microfarads (p=picofarads).
3. £Parts marked with this sign are safety critical components.
AG-D9260
PARTS ARE ACCEPTABLY INSULATED FROM THE SUPPLY CIRCUIT.
They must always be replaced with identical components-refer
to the appropriate parts list and ensure exact replacement. AV Digital Home Theater Receiver
1 st Issue; June 2001